XP-600 Program Manual

XP-600 Program Manual
XP-600 Programming Instructions
®
Note: These Programming Instruction are intended to be used in conjunction with WI847C,
please refer to WI847C for additional information, instructions and definitions.
DEALER PROGRAM MODE
Hexadecimal Data Entry
To Enter a hexadecimal digit
enter the following:
A=
B=
C=
D=
E=
F=
Scroll Key
Use this key to scroll
through data that has been
entered in Programming
Enter
NOTE:
Entering Dealer Program Mode is not permitted while the panel
is Armed, Reporting, or the Bell Output is on. To Enter Dealer
Mode while the Bell is ON or the panel is Reporting or Armed;
power up the panel and enter Dealer Mode within the first 3
key clears the 3 minute timer.
minutes. Pressing the
"
Exiting Dealer Program Mode
DEFAULTING THE PANEL
After 15 minutes of keypad inactivity the keypad
will emit a steady tone indicating the panel has been
left in Dealer Program Mode. Enter Dealer Code to
key to return to Dealer
exit or press the
Program mode.
- KEYPAD KEY DEFINITION
Entering Dealer Program Mode
NOTE:
$50('
5($'<
6<67(0
),5(
$&
*
*
Set Key
Press this key before
entering a Programming Block Number.
=21( =21( =21( =21( Blank Key
Press this key to disable all features within a LED type Programming Block or to blank out digits in
a Direct Entry type Programming
Block.
=21( =21( 1$3&2
+
1. Remove power from the panel.
2. Remove all wiring from terminal
15 (PGM) and terminal 3.
3. Connect terminal 15 (PGM) to
terminal 3.
4. Apply power to the XP-600 control panel.
5. After a few seconds the ARMED,
READY and
SYSTEM TROUBLE LEDs will flash.
6. The keypad will beep 3 times
indicating the panel default values have been loaded.
7. Remove wiring between terminal
15 (PGM) and terminal 3.
8. Re-install original wiring for terminal 15 (PGM) and terminal 3.
Note: Any programming in
Dealer Options 1 [96] and Dealer
Options 2 [97] will not be defaulted. If Dealer Code Lockout
has been programmed the panel
will not default the Dealer Code.
The Event Log will be erased
when the panel is defaulted.
Dealer Code
(4) (5) (6) (7)
ARMED
ON
READY
OFF
9
SYSTEM
Indicates the panel is in Dealer
Program Mode. The panel is
ready for a programming block
number to be entered.
FLASHING
Default Dealer Code shown in parentheses
Enter
Dealer Code
(4) (5) (6) (7)
ARMED
FLASHING
READY
FLASHING
9
SYSTEM
FLASHING
Indicates the panel is
Ready to exit Dealer
Program Mode. Enter
the Dealer Code to exit.
WI847C 8/97
Wi847c
page 1
Tuesday, September 16, 1997 08:35
7\SHV RI 3URJUDPPLQJ %ORFNV
LED Programming Block
Enable features by pressing the key that corresponds to the associated feature; the LED will turn ON. To disable a feature press the key
again; the LED will turn OFF. To disable all features within a LED Type Programming Block press the
key; all LEDs will turn OFF.
LED Programming Block Example
Program zones 2 and 3 as Follower Zones.
1
02 Exit/Entry Follower
OFF
1. Enter Programming Block 02, by pressing
(Beep), then
(Beep).
2. Press the
key to select zone 2.
3. Press the
key to select zone 3.
OFF
OFF
OFF
OFF
OFF
Direct Entry Programming Block
Enter data directly. For hexadecimal entries of A-F, use the
1
²
²
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
key +
through
=21( =21( =21( =21( =21( =21( keys, respectively. Use the
key to blank out digits in Direct Entry type programming blocks. Default values are shown in parentheses.
Direct Entry Programming Example 1
Program the panel for a 60 second Exit Delay.
1. Press
2. Press
2
Zone 2 and Zone 3
LED Type
Programming LEDs are ON indicating that zones 2
Block
and 3 have been
programmed as follower zones.
Default
(Beep)
(Beep)
2
Wi847c
page 2
Press
Press
Press
Press
0
6
0 Exit Delay, seconds
Direct Entry
Type
Programming
Blocks
(0) (4) (5) Maximum Entry 255
.
Direct Entry Programming Example 2
(Hexadecimal data entry)
Program Telephone Prefix Number with a 9E.
1.
2.
3.
4.
10 Exit Delay
(Beep)
(Beep).
44 Dialing Prefix
9
ARMED
OFF
READY
FLASHING
9
SYSTEM
E
FLASHING
Indicates the panel is in
Dealer Program Mode and
the next digit entered will be
interpreted as a Hexadecimal digit. Valid entries are
1-6 (A-F).
Tuesday, September 16, 1997 08:35
Viewing Data in Programming Blocks
To view data within a programming Block, enter the Program Block Number, then press the
key, continue pressing the
the Programming Block have been viewed. Data will be displayed in the binary format shown in the table below:
0/Blank
1
2
3
4
5
6
7
8
9
*A/0
B
C
D
E
F
*
ZONE 1
ZONE 2
ZONE 3
In the following Programming Blocks, data that has
been entered as a ‘0’ will
be displayed as an ‘A’:
Subscriber ID Numbers,
Phone Numbers, Pager
Leading and Trailing digits
and Report Codes.
Press
to enter Programming Block 44. The 1st
digit of Programming Block 44 is displayed.
44 Dialing Prefix
Data = 9
ZONE 1
Press the
(800) 645-9440
ZONE 4
key to view the 2nd digit.
9
E
NOTE:
The Following Programming Options are not
permitted for UL installations: [05], [06], [23-2],
[26-3] and [26-4].
ZONE 2
ZONE 3
2
For Technical Assistance, Contact
the Napco Toll
Free Helpline ZONE LED OFF
Example: Viewing the Dialing Prefix
A Dialing Prefix of 9E has been programmed at Programming Block Number 44 (outside access number). Follow the steps below to view the data.:
1
key until all digits within
NOTE:
ZONE 4
ZONE LED ON
The UL symbol by a
programming Block indicates the programming
option is not permitted
for UL installations.
Data = E
ZONE 1
ZONE 2
ZONE 3
NOTE:
For information about
programming blocks refer to XP-600 Installation
Manual WI846C.
ZONE 4
3
Wi847c
page 3
Tuesday, September 16, 1997 08:35
=RQH )HDWXUHV
03 Auto Bypass Reentry Zones
00 Exit/Entry Zones
Default
Default
UL
06 Open Circuit Zones
Default
Default
ON
Zone 1
OFF
Zone 1
OFF
Zone 1
OFF
Zone 2
OFF
Zone 2
OFF
Zone 2
OFF
Zone 3
OFF
Zone 3
OFF
Zone 3
OFF
OFF
OFF
Zone 4
Zone 5
OFF
OFF
Zone 4
Zone 5
OFF
Zone 4
Zone 5
OFF
Zone 6
OFF
Zone 6
OFF
Zone 6
04 24 Hour Protection Zones
01 Home/Away with Delay Zones
Default
Default
OFF
Zone 1
ON
Zone 1
OFF
Zone 2
OFF
Zone 2
ON
Zone 2
OFF
Zone 3
OFF
Zone 3
ON
Zone 3
OFF
OFF
OFF
Zone 4
Zone 5
ON
OFF
Zone 4
Zone 5
ON
Zone 4
Zone 5
OFF
Zone 6
OFF
Zone 6
ON
Zone 6
UL
ON
Zone 1
ON
Zone 2
ON
Zone 3
ON
ON
Zone 4
Zone 5
ON
Zone 6
Default
Zone 1
Default
See wiring
diagram for
Open Circuit
wiring.
07 Burg (Steady) Output
OFF
02 Exit/Entry Follower Zones
09 Selective Bypass
05 40 ms Loop Response Zones
Default
08 Programmable Output (PGM)
Default
OFF
Zone 1
OFF
Zone 1
ON
Zone 1
OFF
Zone 2
OFF
Zone 2
ON
Zone 2
OFF
Zone 3
OFF
Zone 3
ON
Zone 3
OFF
OFF
OFF
Zone 4
Zone 5
ON
OFF
Zone 4
Zone 5
ON
Zone 4
Zone 5
OFF
Zone 6
OFF
Zone 6
ON
Zone 6
4
Wi847c
page 4
Tuesday, September 16, 1997 08:35
6\VWHP 7LPHV
10 Exit Delay
23 Programmable Output (PGM) Features 1
17 Wireless Smoke Supervisory Timer
Default
Smoke Supervisory Timer, hours
Exit Delay, seconds
(0)
(4)
(5)
Maximum Entry 255
11 Entry Delay
(8)
18 Test Timer Offset
(3)
(0)
Maximum Entry 255
12 Burg (Steady) Output Time-out
Bell Time-out, minutes
(0)
(0)
(5)
Maximum Entry 255
(1)
(2)
13 Fire (Pulsed) Output Time-out
Bell Time-out, minutes
(0)
(0)
(0)
Maximum Entry 255
14 Test Timer Interval
OFF
Zn 1 LED ON = *Keypad Fire (
)
OFF
(0)
(1)
Zn 2 LED ON = *Keypad AUX (
)
ON
Zn 3 LED ON = *Keypad Panic (
OFF
Zn 4 LED ON = *Ambush (6th User Code)
*See Note 1
ON
Zn 1 LED ON = Audible panic
Maximum Entry 255
OFF
Zn 2 LED ON = Exit/Entry with Urgency
ON
Zn 3 LED ON = Display Bypass (ARMED)
Line Cut Time-to-Fail, seconds
(0) (0) (0) Enable Feature-Valid Entries 10-255
16 Wireless Supervisory Timer
Supervisory Timer, hours
(1)
(2) Maximum Entry 26
Zn 4 LED ON = Disable Code Entry Beeps
22 Miscellaneous Features 1
Zn 1 LED ON = Fire
OFF
Zn 2 LED ON = AUX
OFF
Zn 3 LED ON = Panic
OFF
Zn 4 LED ON = Test Timer
OFF
Zn 1 LED ON = AC Fail
OFF
Zn 2 LED ON = Low Battery
OFF
Zn 3 LED ON = *Trouble
26 Miscellaneous Features 2
Default
OFF
Zn 1 LED ON = Momentary Keyswitch Arming
OFF
Zn 2 LED ON = Reserved
UL
OFF
Zn 3 LED ON = Inhibit Fail to Communicate
UL
OFF
Zn 4 LED ON = Inhibit Low Battery Display
Default
OFF
Zn 1 LED ON = Abort Delay
ON
Zn 2 LED ON = Easy Arm/Easy Exit
ON
Zn 3 LED ON = Swinger Shutdown
OFF
Zn 4 LED ON = Bell on Line Cut (Armed)
NOTE 1:
Additional programming required for reporting, see Blocks [36]&[56].
UL Installations: If Keypad Fire [20-1] is enabled, the keypad must be mounted
within (3) three feet from the Control Panel.
Wi847c
page 5
OFF
OFF
Zn 4 LED ON = Armed
*See Note 3
21 Keypad Features 2
OFF
)
Default
)
Test Timer, days
15 Line Cut Time-to-Fail (Disabled = 000)
Zn 3 LED ON = *Follow Keypad Sounder
25 Programmable Output (PGM) Features 3
Default
(0)
Zn 2 LED ON = *Access Output (
OFF
Default
6\VWHP )HDWXUHV
Default
Zn 1 LED ON = Audio Verification
OFF
24 Programmable Output (PGM) Features 2
Maximum Entry 23
20 Keypad Features 1
OFF
OFF
Zn 4 LED ON = *Keyfob/Keyswitch Chirp
*See Note 2
Test Timer Offset, hours
Entry Delay, seconds
(0)
UL
Maximum Entry 8
NOTE 2:
Cannot be programmed with any other Programmable Output (PGM) Feature.
NOTE 3:
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Faliure,
Wireless Smoke Low Battery and Wireless Smoke Supervisory Failure.
5
Tuesday, September 16, 1997 08:35
7HOHSKRQH 1XPEHU 3URJUDPPLQJ
30 Subscriber ID Number
34 Zone Report, Telco 1
37 System Reporting, Telco 1
Default
31 Telephone Number 1
Default
ON
Zone 1
OFF
Zn 1 LED ON = AC Fail Report (15 min. report delay)
ON
Zone 2
ON
Zn 2 LED ON = Low Battery Report
ON
Zone 3
OFF
Zn 3 LED ON = *Trouble Report
ON
ON
Zone 4
Zone 5
ON
Zn 4 LED ON = Fire Report
*See Note 2
ON
Zone 6
38 System Restore Report, Telco 1
NOTE:
Default
A fixed Dial Tone Detection (E) is included prior to the Dialing Prefix (Block
Number 44). Programming an E is not required for Telco 1, Telco 2 and
Telco 3. If dial tone detection is not desired select No Dial Tone Detection in
Communicator Features (Block Number 46). Program a D if a 4 second
delay is required.
35 Zone Restore Report, Telco 1
Default
32 Receiver Format
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Disabled
Ademco Slow
Radionics Slow
Silent Knight Fast
Universal High Speed
Reserved
Point ID
Pager
(4)
OFF
Zone 1
OFF
Zone 2
OFF
Zone 3
OFF
OFF
Zone 4
Zone 5
OFF
Zone 6
Zn 2 LED ON = Battery Restore Report
OFF
Zn 3 LED ON = Trbl Restore Report
OFF
Zn 4 LED ON = Fire Restore Report
Default
Default
OFF
Zn 1 LED ON = *KP Fire
ON
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
OFF
OFF
Zn 2 LED ON = Sumcheck
ON
Zn 2 LED ON = *KP AUX (
Zn 3 LED ON = *KP Panic (
OFF
Zn 3 LED ON = Single Digit
OFF
Zn 4 LED ON = No Handshake
OFF
Zn 4 LED ON = Test Timer
*See Note 1
Default
Zn 1 LED ON = AC Restore Report
OFF
39 Opening Closing Report, Telco 1
36 System Reporting, Telco 1
33 Receiver Options
OFF
(
)
)/Ambush
OFF
Zn 1 LED ON = User 1 Reporting
OFF
Zn 2 LED ON = User 2 Reporting
OFF
Zn 3 LED ON = User 3 Reporting
OFF
OFF
Zn 4 LED ON = User 4 Reporting
Zn 5 LED ON = User 5 Reporting
OFF
Zn 6 LED ON = User 6 Reporting
NOTE 1:
Requires features to be enabled, see block [20].
)
NOTE 2:
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Faliure,
Wireless Smoke Low Battery, Wireless Smoke Supervisory Failure.
ZONE 3 TX LOW BATTERY
SMOKE 2 LOW BATTERY
“RF TRAN LOW BAT, ZN03”
“RF TRAN LOW BAT, ZN10”
6
Wi847c
page 6
Tuesday, September 16, 1997 08:35
%DFNXS 7HOHSKRQH 3URJUDPPLQJ
3DJHU 3URJUDPPLQJ
40 Subscriber ID Number (Telco 2)
47
44 Dialing Prefix
Dialing Prefix for Telco 1, Telco 2
& Telco 3.
Leading Digits
(0)
(0)
(0)
(0)
41 Telephone Number 2
45 Communicator Features 1
Default
NOTE:
A fixed Dial Tone Detection (E) is included prior to the Dialing Prefix (Block
Number 44). Programming an E is not required for Telco 1, Telco 2 and
Telco 3. If dial tone detection is not desired select No Dial Tone Detection in
Communicator Features (Block Number 46). Program a D if a 4 second
delay is required.
ON
Zn 1 LED ON = Communicator Enabled
ON
Zn 2 LED ON = DTMF w/ Rotary Back up
OFF
Zn 3 LED ON = DTMF only
OFF
Zn 4 LED ON = Backup to Telco 2
48
Trailing Digits
42 Receiver Format
46 Communicator Features 2
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Ademco Slow
Radionics Slow
Silent Knight Fast
Universal High Speed
Reserved
Point ID
Pager
Default
(4)
OFF
Zn 1 LED ON = No Dial Tone Detection
OFF
Zn 2 LED ON = 2:1 Rotary Dialing
OFF
Zn 3 LED ON = Backup if < 4 attempts
OFF
Zn 4 LED ON = Reserved
*(C) *See Note 1
49 Pager Option
Default
OFF
Zn 1 LED ON = Skip Alarm Data
OFF
Zn 2 LED ON = Reserved
OFF
Zn 3 LED ON = Reserved
OFF
Zn 4 LED ON = Reserved
43 Receiver Options
Default
ON
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
OFF
Zn 2 LED ON = Sumcheck
OFF
Zn 3 LED ON = Single Digit
OFF
Zn 4 LED ON = No Handshake
NOTE 1:
C = TouchTone #. This is the typical terminating digit for
most paging systems. Recommended, but may not be
required by paging system. D = 2 second delay.
7
Wi847c
page 7
Tuesday, September 16, 1997 08:35
7HOHSKRQH 1XPEHU 3URJUDPPLQJ
50 Subscriber ID Number
54 Zone Report, Telco 3
57 System Reporting, Telco 3
Default
31 Telephone Number 3
Default
OFF
Zone 1
OFF
Zn 1 LED ON = AC Fail Report (15 min. report delay)
OFF
Zone 2
OFF
Zn 2 LED ON = Low Battery Report
OFF
Zone 3
OFF
Zn 3 LED ON = *Trouble Report
OFF
OFF
Zone 4
Zone 5
OFF
Zn 4 LED ON = Fire Report
*See Note 2
OFF
Zone 6
58 System Restore Report, Telco 3
NOTE:
Default
A fixed Dial Tone Detection (E) is included prior to the Dialing Prefix (Block
Number 44). Programming an E is not required for Telco 1, Telco 2 and
Telco 3. If dial tone detection is not desired select No Dial Tone Detection in
Communicator Features (Block Number 46). Program a D if a 4 second
delay is required.
55 Zone Restore Report, Telco 3
Default
52 Receiver Format
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Disabled
Ademco Slow
Radionics Slow
Silent Knight Fast
Universal High Speed
Reserved
Point ID
Pager
(4)
OFF
Zone 1
OFF
Zone 2
OFF
Zone 3
OFF
OFF
Zone 4
Zone 5
OFF
Zone 6
Zn 2 LED ON = Battery Restore Report
OFF
Zn 3 LED ON = Trbl Restore Report
OFF
Zn 4 LED ON = Fire Restore Report
Default
Default
OFF
Zn 1 LED ON = *KP Fire
ON
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
OFF
OFF
Zn 2 LED ON = Sumcheck
ON
Zn 2 LED ON = *KP AUX (
Zn 3 LED ON = *KP Panic (
OFF
Zn 3 LED ON = Single Digit
OFF
Zn 4 LED ON = No Handshake
OFF
Zn 4 LED ON = Test Timer
*See Note 1
Default
Zn 1 LED ON = AC Restore Report
OFF
59 Opening Closing Report, Telco 3
56 System Reporting, Telco 3
53 Receiver Options
OFF
(
)
)/Ambush
OFF
Zn 1 LED ON = User 1 Reporting
OFF
Zn 2 LED ON = User 2 Reporting
OFF
Zn 3 LED ON = User 3 Reporting
OFF
OFF
Zn 4 LED ON = User 4 Reporting
Zn 5 LED ON = User 5 Reporting
OFF
Zn 6 LED ON = User 6 Reporting
NOTE 1:
Requires features to be enabled, see block [20].
)
NOTE 2:
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Faliure,
Wireless Smoke Low Battery, Wireless Smoke Supervisory Failure.
ZONE 3 TX LOW BATTERY
SMOKE 2 LOW BATTERY
“RF TRAN LOW BAT, ZN03”
“RF TRAN LOW BAT, ZN10”
8
Wi847c
page 8
Tuesday, September 16, 1997 08:35
5HSRUW &RGHV
60 Zone Report Codes
Zone 1 Alarm Code
(3)
Zone 2 Alarm Code
(3)
Zone 3 Alarm Code
62 Zone Codes
65 Opening and Closing Code
Zone 1, 2, 3, 4, 5 & 6 Restore Code
NOTE:
The second digit of the Report Code is the number of
the zone that is reporting.
For example zone 5 report
code (default of 3) would be
35.
(3)
(E)
(C) Closing Code
Zone 1, 2, 3, 4, 5 & 6 Trouble Code
(F)
(B)
63 System Report Codes
Zone 4 Alarm Code
(3)
Keypad Fire (
Zone 5 Alarm Code
(1)
(3)
(1)
Keypad AUX (
Zone 6 Alarm Code
(3)
(2)
(3)
(2)
(1)
(F)
(F)
(F)
(9)
Keypad Panic (
66 Ambush Report Code
)
(2)
)
AC Fail
(F)
(3)
Zone 2 Alarm Code
(3)
Zone 3 Alarm Code
(3)
Zone 4 Alarm Code
(3)
Zone 5 Alarm Code
(3)
1
2
3
4
5
6
7
8
9
A
B
FIRE
PANIC
BURGLARY
HOLDUP
GENERAL ALARM
RESERVED
GAS ALARM
HEAT ALARM
RESERVED
AUXILIARY
24 HOUR ALARM
(8)
*Trouble
(F)
Enhanced Communicator Features
67 Telephone Number 1
Default
Low Battery
Zone 1 Alarm Code
(2)
)
Test Timer
61 Point ID Report Codes
Opening Code
(1)
OFF
Zn 1 LED ON = Opening after Alarm (Cancel Code)
OFF
Zn 2 LED ON = Conditional Closing
OFF
Zn 3 LED ON = Reserved
OFF
Zn 4 LED ON = Reserved
Fire
(1) (1)
*See Note 1
68 Telephone Number 3
Default
64 System Restore Code
(E)
Zone 6 Alarm Code
OFF
Zn 1 LED ON = Opening after Alarm (Cancel Code)
OFF
Zn 2 LED ON = Conditional Closing
OFF
Zn 3 LED ON = Reserved
OFF
Zn 4 LED ON = Reserved
(3)
NOTE 1:
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Faliure, Wireless Smoke Low Battery and Wireless Smoke Supervisory Failure.
9
Wi847c
page 9
Tuesday, September 16, 1997 08:35
:LUHOHVV
7UDQVPLWWHUV
RF ID #
Point
71 Zone 1
:
72 Zone 2
:
73 Zone 3
:
Programming Example
Enter the RF ID# located on
the Transmitter, Key Fob and
Smoke Detector labels.
Map point 1 of a window door transmitter, with RF ID# 0012B0:0
to Zone 3.
73 Zone 3
0
0
1
:
75 Zone 5
:
4. Enter
3. Enter
:
76 Zone 6
.H\IREV
RF ID #
AUX 1 AUX 2
81 Keyfob 1
:
82 Keyfob 2
:
:
83 Keyfob 3
84 Keyfob 4
To Enter a hexadecimal digit enter the following:
Wi847c
page 10
A=
AUX 1 & 2
Programming
1
2
3
4
5
6
7
8
:
Hexadecimal Data Entry
10
Enter the point number to be
associated with the zone. If only
one point of GEM-TRANS2 is
used, enter a 1 in this location.
For GEM-GB, GEM-DT, GEMPIR enter a 1 in this location.
Panic
AUX
Bell ON
PGM
Instant
Access on PGM
Full Set System
Interior
B
0
:0
1
74 Zone 4
1. Enter Dealer Mode.
(beeps)
2. Enter
RF ID # XXXXXX:X
2
(beeps)
(beeps)
Hexadecimal B Entry
Note: If the RF ID# in step 3 is not entered correctly the
keypad will emit a 1 second tone indicating incorrect entry.
Repeat steps 2 - 4 above.
6PRNH 'HWHFWRUV
RF ID #
85 Smoke 1
:
86 Smoke 2
:
87 Smoke 3
:
88 Smoke 4
:
B=
C=
D=
E=
F=
Tuesday, September 16, 1997 08:35
'RZQORDGLQJ
'HDOHU 3URJUDPPLQJ
90 Callback Telephone Number
94 Dealer Code
97 Dealer Options 2
Default
(4) (5) (6) (7)
91 Ring Count
95 User 1 Code
OFF
Zn 1 LED ON = *International Dialing Protocol
OFF
Zn 2 LED ON = *Invert Bell Output
OFF
Zn 3 LED ON = System Trouble Auto Reset
OFF
Zn 4 LED ON = User 1 Code-Program only
*See Note 1
(0) (9) Maximum Entry 15
(1) (2) (3) (4)
98 Number of Re-Dials
92 Downloading Features
96 Dealer Options 1
Default
Default
ON
Zn 1 LED ON = Ring Method
OFF
Zn 2 LED ON = Answering Machine override
OFF
Zn 3 LED ON = Command 6(
OFF
Zn 4 LED ON = Signal Strength Test Mode
) Download
OFF
Zn 1 LED ON = Dealer Code Lockout
ON
Zn 2 LED ON = User 1 Code Lockout
OFF
Zn 3 LED ON = UL Household Fire
OFF
Zn 4 LED ON = Fire Trouble on Fire LED
(9)
NOTE 1:
International Features
93 Auto Download ID Number
11
Wi847c
page 11
Tuesday, September 16, 1997 08:35
XP-600 WIRING DIAGRAM
This equipment should be installed in accordance with Chapter 2
of the National Fire Alarm Code, ANSI/NFPA 72-1993 (National
Fire Protection Association Batterymarch Park, Quincy MA
02269). and local codes. Information describing proper installation, operation, testing, maintenance, evacuation planning, and
repair service is to be provided with this equipment. UL Listed
Energy Cable is required.
(REFER TO INSTALLATION INSTRUCTIONS WI47C)
E1
RED
RESIDENTIAL BURG (4 HOUR STANDBY)
COMBINED STANDBY = 500 mA
BELL = 2.0 AMP
RECHARGEABLE
BATTERY
12 VDC 4AH OR 7AH
E2
(2)
RESIDENTIAL FIRE (4 HOUR STANDBY)
COMBINED STANDBY = 500 mA
BELL = 65 mA
BLACK
(3)
COLD WATER GROUND
CONNECTION
USE ONLY COLD-WATER
PIPE OR BURIED GROUND
ROD. USE AT LEAST #16
AWG WIRE.
+6
-7
FIRE
GND
ALL ZONE RESISTORS MUST BE INSTALLED,
EVEN IF ZONE IS NOT USED.
(2)
COMBINED STANDBY = KEYPAD CURRENT +
AUX POWER CURRENT + FIRE POWER + PGM
CURRENT.
ZONE 2
ZONE 3
RING
.
2.2K EOLR
(SUPERVISED)
TELCO
PHONE
To RJ31X
(Supervised)
RPX-6
WARNING
TO PREVENT RISK
OF ELECTRIC SHOCK
DISCONNECT TELEPHONE
LINES PRIOR TO SERVICING
GEM-RECV-XP8
12
+PWR
(E)
Normally Open Zone Wiring
Wire the normally open contact
as shown (Zone 4). Program
the zone for Open Circuit [06]
operation.
.
24 HOUR STANDBY REQUIRES A 7AH BATTERY.
ZONE 1
.
(1)
(E)
19
TIP
BRN
(E)
.
18
RING
GRAY
(E)
ZONE 6
.
(E)
17
TIP
GRN
ZONE 5
.
.
*2/'
ZONE 4
A'
+
/2
(1)
16
Programmable
Output
(Z)
P$ 0$;
(Z)
15
GND GREEN PGM
(-)
REMOTE BUS
%/.
+
(Z)
14
+PWR
+
2.2K EOLR
(3)
BELL
*51
+
+10 -11 +12 -13
+
(Z)
:+,7( 5('
-9
FIRE
PWR
3.9K
25$1*(
+8
5('
EARTH
GROUND
+5
.
GOLD
RED RED
-4
.
RED
+3
.
Zone
TM
Doubling
Resistors
2
AUX POWER OUTPUT 10-12.5 VDC
EZ
1
16 VAC 20 VA
TRANSFORMER
NAPCO TRF12
(OR EQUIVALENT
SEE WI850A).
Class 2
Transformer.
DO NOT
connect to
switched
outlet.
ALL OUTPUTS ARE CURRENT LIMITED
RED
2.2K
(E)
RESIDENTIAL FIRE (24 HOUR STANDBY)
COMBINED STANDBY = 120 mA
BELL = 95 mA
FT2200
ZONE 4
XP-600 Terminals
RED
(Z)
4-Wire Fire Wiring
BLACK
BROWN
(E)
BROWN
Power
Out (+)
Power
Out (-)
Power
In (+)
Power
In (-)
Fire Loop Fire Loop
Out
In
8 Fire Power
7 Ground
8 Fire Power
9 Fire
ZONE 1
12
Wi847c
page 12
Tuesday, September 16, 1997 08:35
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement