Cisco | NAS200 | User guide | Cisco NAS200 User guide

USER GUIDE
Network Storage System
with 2 Bays
Model: NAS200
About This Guide
About This Guide
Icon Descriptions
While reading through the User Guide you may see
various icons that call attention to specific items. Below is
a description of these icons:
NOTE: This check mark indicates that there is
a note of interest and is something that you
should pay special attention to while using the
product.
WARNING: This exclamation point indicates
that there is a caution or warning and it is
something that could damage your property or
product.
WEB: This globe icon indicates a noteworthy
website address or e-mail address.
Online Resources
Website addresses in this document are listed without
http:// in front of the address because most current web
browsers do not require it. If you use an older web browser,
you may have to add http:// in front of the web address.
Resource
Website
Linksys
www.linksys.com
Linksys International
www.linksys.com/international
Glossary
www.linksys.com/glossary
Network Security
www.linksys.com/security
Copyright and Trademarks
Linksys, Cisco and the Cisco Logo are
registered trademarks or trademarks of
Cisco Systems, Inc. and/or its affiliates
in the U.S. and certain other countries.
Copyright © 2008 Cisco Systems, Inc. All
rights reserved. Other brands and product
names are trademarks or registered
trademarks of their respective holders.
Network Storage System with 2 Bays
i
Table of Contents
Chapter 1: Product Overview
1
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Drive Bay Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Notification Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chapter 2: Configuration Using the Setup Wizard
3
How to Access the Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Set up Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Set up Second Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Backup Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Advanced Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Install Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 3: Advanced Configuration
11
How to Access the Web-Based Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
My Files > Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
My Files > My Downloads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
My Files > Personal Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Administration > Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Administration > Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Administration > Shared Folders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Administration > System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
E-Mail Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Media Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Disk Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Disk Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Chapter 4: Use
26
Access to the Network Storage System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
How to Access the Network Storage System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
USB Storage Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
How to Use the Network Drive Mapping Utility . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Appendix A: Troubleshooting
31
Appendix B: Specifications
33
Appendix C: Warranty Information
34
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Appendix D: Regulatory Information
36
FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Network Storage System with 2 Bays
ii
Table of Contents
Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste
Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Appendix E: Software License Agreement
41
Software in Linksys Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Software Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Network Storage System with 2 Bays
iii
Product Overview
Chapter 1
Chapter 1:
Product Overview
Thank you for choosing the Linksys Network Storage
System with 2 Bays. It features two SATA hard drive bays
so you can add storage space to your network. There are
also two USB ports that let you add USB hard drives for
additional storage space, or you can connect a USB flash
disk to access your portable files. (USB hard drives may
require external power supplies.)
WARNING: Do not block the air vents, and do
not stack devices on top of the Network Storage
System; otherwise, overheating can occur.
(Air vents are located on the sides of the
Network Storage System. Keep the area around
the Network Storage System clear.)
Front Panel
DISK 1 (Green) The DISK 1 LED serves two
purposes. The LED is continuously lit when
the hard drive in the top bay is ready for use. It
flashes when the hard drive is reformatting or
rebuilding with Disk 2 (RAID 1 mode).
DISK 2 (Green) The DISK 2 LED serves two
purposes. The LED is continuously lit when the
hard drive in the bottom bay is ready for use. It
flashes when the hard drive is reformatting or
rebuilding with Disk 1 (RAID 1 mode).
USB 1-2 (Green) The USB LED serves multiple
purposes. The LED is continuously lit when
the USB device is connected through the
corresponding port. It flashes when the
Network Storage System is accessing the USB
device. After the LED powers off, the USB device
can be removed.
Back Up Button Press the Back Up button to
initiate backup jobs specified by the backup
software on your computer. (Your computer
must be powered on for the jobs to run.)
Back Panel
POWER (Green/Orange) The POWER LED
serves multiple purposes. It flashes green
when the Network Storage System boots up,
shuts down, prepares a disk, or scans a disk.
The LED flashes green and orange when the
Network Storage System upgrades its firmware.
It is continuously lit green when the Network
Storage System is ready for use. The LED is
continuously lit orange when there is an error.
(See “Appendix A: Troubleshooting” for more
information.)
ETHERNET (Green) The ETHERNET LED serves
two purposes. The LED is continuously lit when
a device is connected through the Ethernet
port. It flashes to indicate network activity.
DISK ACT (Green) The DISK ACT LED flashes
when the Network Storage System is accessing
data on the disk.
DISK FULL (Green) The DISK FULL LED flashes
when available disk capacity is less than 2% of
total capacity or lower than the number you set
through the web-based utility.
Network Storage System with 2 Bays
POWER Button Push the POWER button to
power on or off the Network Storage System.
POWER The POWER port connects to the
included power adapter.
ETHERNET The ETHERNET port connects to
an Ethernet network device, such as a router or
switch.
USB 1 The USB 1 port connects to your USB
storage device. Press the USB 1 button to
eject the device from the USB 1 port. After
the Network Storage System beeps once and
the USB 1 LED powers off, you can remove the
device.
1
Product Overview
Chapter 1
USB 2 The USB 2 port connects to your second
USB storage device. Press the USB 2 button
to eject the device from the USB 2 port. After
the Network Storage System beeps once and
the USB 2 LED powers off, you can remove the
device.
RESET The RESET button has two functions:
•• To reset the network settings, such as
the IP address, of the Network Storage
System, press and hold this button for
two seconds. The Network Storage
System resets to DHCP and tries to
get an IP address from the DHCP
server on your network. If there is no
DHCP server on your network, the
Network Storage System will be set to
its default IP address, 169.254.xx.xx
(the x’s represent randomly generated
numbers). The Network Storage System
beeps once to indicate that the reset
has occurred.
•• To reset the password of the Network
Storage System to its default value
of admin, press and hold this button
for 10 seconds. The Network Storage
System beeps twice to indicate that the
reset has occurred.
Drive Bay Doors
The drive bay door covers the opening of the drive bay,
which holds the hard drive. Push together the clips to
remove the drive bay door. Disk 1 is inserted into the
upper bay, and Disk 2 is inserted into the lower bay.
Notification Sounds
The Network Storage System emits sounds to indicate
different activities or status information.
Notification Sounds
Sound
Meaning
Power
or
Reset
button
pushed
1 beep
USB device ready to be removed
2 beeps
Reset button pushed and held for over
10 seconds
3 beeps every Available disk capacity is less than 2%
15 seconds for 3 of total capacity or the number you set
through the web‑based utility (2 or 5 GB)
minutes
Network Storage System with 2 Bays
2
Configuration Using the Setup Wizard
Chapter 2
Chapter 2:
Configuration Using the
Setup Wizard
3. You have multiple options on this screen:
After first-time installation of the Network Storage
System with the Setup Wizard (located on the CD-ROM),
the Network Storage System is ready for use. However,
additional configuration is available with the Setup Wizard
and web-based utility.
Use the Setup Wizard for the following tasks:
•• Configure another computer to use the Network
Storage System
•• Add a second hard drive to the already configured
Network Storage System
•• Install backup software on your computer
•• Access the web-based utility
•• Install the Linksys Network Drive Mapping Utility
•• Access the User Guide on the CD
Welcome Screen with Options
–– Set up NAS200 Install the Network Storage
System for the first time. (The instructions are
covered in the Quick Installation.)
–– Set up Computer Configure another computer to
use the Network Storage System.
Use the web-based utility for advanced configuration
(refer to “Chapter 3: Advanced Configuration” for details).
–– Set up Second Drive Add a second hard drive to
How to Access the Setup Wizard
–– Exit Use this option to close the Setup Wizard.
1. Insert the Setup Wizard CD-ROM into your PC’s CD‑ROM
drive. The Setup Wizard should run automatically,
and the Welcome screen should appear. If it does not,
click Start and then Run. In the field provided, enter
D:\SetupUtility.exe (if “D” is the letter of your CD-ROM
drive).
2. Click the Click Here to Start button.
the already configured Network Storage System.
–– Backup Software Install a third-party program to
run backup jobs.
–– Advanced Setup Use this option to access the
web-based utility.
–– Install Utility Use this option to install the Network
Drive Mapping Utility.
–– User Guide Use this option to open the pdf of this
User Guide.
Set up Computer
Follow these instructions to configure another computer
to use the Network Storage System.
1. Click Set up Computer.
Welcome Screen
Network Storage System with 2 Bays
3
Configuration Using the Setup Wizard
Chapter 2
2. For the public folder, keep the default drive letter, or
select a different letter from the drop-down menu.
Click Next.
5. The network drive(s) are mapped to your computer.
Click Exit to exit the Setup Wizard, or click Next to
return to the Welcome screen.
Map Network Drive
3. To install the Linksys Network Drive Mapping Utility on
your computer, click Yes.
Network Drive Mapped
The computer has been configured.
Set up Second Drive
Install Drive Mapping Utility
4. The Setup Wizard automatically installs the utility.
Click OK.
Drive Mapping Utility Installed
NOTE: Make sure your second hard drive
is a 3.5-inch, Serial-ATA (SATA) hard drive.
If you plan to stripe (RAID 0) or mirror
(RAID 1) your drives, then match the drive sizes
for maximum drive use.
WARNING: Low-profile or half-height hard
drives can be used at your own risk; however,
Linksys does not support the use of these drives
as they are not securely held in place inside the
Network Storage System.
Follow the instructions to add a second hard drive to
your previously configured Network Storage System. If
you physically install a second drive without running the
Setup Wizard, then the second drive will not be formatted.
It will have to be manually formatted using the web-based
utility (refer to “Chapter 3: Advanced Configuration”).
Network Storage System with 2 Bays
4
Configuration Using the Setup Wizard
Chapter 2
1. Click Set up Second Drive.
Physical Installation of the Second Hard Drive
Set up Second Drive
2. The Setup Wizard explains that these instructions
cover the physical installation and drive configuration.
Click Next.
4. The Setup Wizard automatically searches for any
Network Storage System on your network. If it is not
detected, check its cable connections, and make sure
it is powered on. Click Search Again to locate the
Network Storage System.
Select the appropriate Network Storage System. Click
Next.
Overview
3. To install the second hard drive:
a. Power off the Network Storage System.
Network Storage System Detected
b. Push together the clips, and remove the lower
drive bay door.
c. Lift up the ribbon.
d. Make sure the connector side of the drive faces the
bay, and the label side faces up.
e. Make sure the drive is inserted under the ribbon.
Push the drive in until it snugly fits in the bay.
f. Replace the drive bay door.
g. Wait until you hear the Network Storage System
beep twice. Then click Next.
Network Storage System with 2 Bays
5
Configuration Using the Setup Wizard
Chapter 2
5. Select the appropriate configuration for your drive
usage:
6. Review the new settings. If they are correct, click Save.
If you would like to change them, click Back to return
to the previous screen.
NOTE: If you change the drive configuration
setting (for example, from Separate Disks to
RAID 1), both drives will be reformatted and all
current data will be erased. Back up any preexisting data before reconfiguring your drives.
–– Maximum Storage - Separate Disks Drives seen
separately.
–– Maximum
Storage
Multiple
Disks
(JBOD/LVM) Drives seen as a single virtual drive.
–– Maximum Security - Mirroring (RAID 1) Requires
two hard drives.
–– Maximum Speed - Striping (RAID 0) Requires
two hard drives.
Click Next.
Confirm New Settings
7. To confirm that you want to format your drives and
erase all data on them, click Next.
WARNING: Before you format drive(s), back
up pre-existing data because all data on
your drive(s) will be erased when they are
formatted.
If the drives have been previously formatted by the
Network Storage System, click Skip to continue
without reformatting.
Select Drive Configuration
Confirm Formatting
Network Storage System with 2 Bays
6
Configuration Using the Setup Wizard
Chapter 2
8. Click Set up Computer.
12.The network drive(s) are mapped to your computer.
Click Exit to exit the Setup Wizard, or click Next to
return to the Welcome screen.
Set up Computer
9. For the public folder of the second hard drive, keep the
default drive letter, or select a different letter from the
drop-down menu. Click Next.
Network Drive Mapped
NOTE: If the utility is already installed on your
computer (you can see it in your list of programs),
the Setup Wizard will skip the installation.
Program Folder
The second hard drive has been installed.
Backup Software
Follow these instructions to install a third-party program
to run backup jobs.
Map Network Drive
1. Click Backup Software.
10.To install the Linksys Network Drive Mapping Utility on
your computer, click Yes.
Install Drive Mapping Utility
11.The Setup Wizard automatically installs the utility.
Click OK.
Drive Mapping Utility Installed
Network Storage System with 2 Bays
Backup Software
7
Configuration Using the Setup Wizard
Chapter 2
2. Click Install.
5. Enter your information in the User Name and Company
Name fields. Then select the users of the backup
software:
•• Anyone who uses this computer (all users)
•• Only for me
Install Backup Software
Click Next.
3. The InstallShield Wizard appears. Click Next.
User Information
Begin Installation of Backup Software
6. Keep the default installation folder, or click Browse to
select a different folder. Click Next.
4. To accept the license agreement, click Yes.
Choose Destination Location
License Agreement
7. The backup software is installed. Click Finish.
Backup Software Installed
Network Storage System with 2 Bays
8
Configuration Using the Setup Wizard
Chapter 2
Double-click the desktop icon to access the software.
3. The Setup Wizard notifies you that a user name and
password are required for access. Click OK.
Desktop Icon for Backup Software
For more information, click Help on the main menu of the
backup software.
Advanced Setup
Follow the instructions to access the web-based utility
through the Setup Wizard.
1. Click Advanced Setup.
User Name and Password Required
4. Enter your information in the User Name and Password
fields. Click OK.
Login Screen
Advanced Setup
2. The Setup Wizard automatically searches for any
Network Storage System on your network. If it is not
detected, check its cable connections, and make sure
it is powered on. Click Search Again to locate the
Network Storage System.
Select the appropriate Network Storage System. Click
Next.
Refer to “Chapter 3: Advanced Configuration” for details
about the web-based utility.
Install Utility
Follow these instructions to install the Network Drive
Mapping Utility.
1. Click Install Utility.
Install Utility
Network Storage System Detected
Network Storage System with 2 Bays
9
Configuration Using the Setup Wizard
Chapter 2
2. Click Yes.
9. The shared folder automatically opens in a separate
window.
Repeat steps 5-8 to map additional network drives.
Install Drive Mapping Utility
3. The Setup Wizard automatically installs the utility.
Click OK.
10.To exit the utility, click Close on the Shared Folder
Mapping screen.
For more information about the utility, refer to “Chapter  4:
Use”.
User Guide
Click this option to access the pdf of this User Guide.
Drive Mapping Utility Installed
4. On the Shared Folder Mapping screen, select the
appropriate Network Storage System.
User Guide
Map Network Drive
To install Adobe Reader, click Yes. To cancel, click No.
5. Select the appropriate shared folder. If you do not see
the folder you want, click Refresh.
6. Keep the default drive letter, or select a different letter
from the drop-down menu. Then click Map.
7. Enter your information in the User Name and Password
fields. Click OK.
Adobe Reader
Login Screen
8. You are notified when the shared folder has been
mapped. Click OK.
Shared Folder Mapped
Network Storage System with 2 Bays
10
Advanced Configuration
Chapter 3
Chapter 3:
Advanced Configuration
The web-based utility appears.
NOTE: When first installing the Network Storage
System, you should use the Setup Wizard on
the Setup CD-ROM. If you want to configure
advanced settings, use this chapter.
After setting up the Network Storage System with the
Setup Wizard (located on the CD-ROM), it is ready for use.
If you want to change its advanced settings, use the webbased utility. This chapter describes each web page of the
utility and each page’s key functions. You can access the
utility via a web browser on a computer connected to your
network router.
Home Screen
Home
On the homepage of the web-based utility, you have
two options, Access My Files and Administration Login.
Additional tabs will be available after you click one of the
main options.
On the homepage of the web-based utility, you have two
options:
How to Access the Web-Based Utility
Administration Login Click this option to manage the
Network Storage System through the web-based utility.
To access the Network Storage System from any computer
using a web browser, follow these instructions:
1. Open your web browser.
2. In the Address field, enter http://<IP_address_of_
the_Network_Storage_System>. Press Enter.
If you do not know its IP address, then run the Setup
Wizard. Click the Click Here to Start button. Then click
Advanced Setup. Select the appropriate Network
Storage System, and its IP address will be displayed. (For
more information, refer to “Chapter 2: Configuration
Using the Setup Wizard”.)
3. A login screen appears. (Non-Windows XP users will
see a similar screen.) The first time you open the
web-based utility, enter admin in the User name and
Password fields. (The default user name and password
is admin. You can set a new password for the admin
user on the Access My Files > Personal Info screen.) Click
OK to continue.
Access My Files Click this option to access folders or
change your password.
My Files > Files
To access folders or change your password:
1. Click Access My Files.
2. Enter your information in the User Name and Password
fields.
3. Click OK.
The Files screen automatically appears. You have two
options available, Files and Personal Info, in the My Files
column. If the Download Manager feature has been
enabled through the Administration > System Options
screen and your login has Download Manager access,
then the My Downloads option will also be displayed.
NOTE: The Download Manager feature lets you
specify download tasks for the Network Storage
System. The advantage is that the Network
Storage System can run the download task
separately, without using your computer. For
example, if you order a movie online, then you
can have the Network Storage System—instead
of your computer—download the movie.
Login Screen
Network Storage System with 2 Bays
11
Advanced Configuration
Chapter 3
Login
My Files > My Downloads
The login you use to access your files is displayed.
If the Download Manager feature has been enabled
through the Administration > System Options screen and
your login has Download Manager access, then the My
Downloads screen will be available. Configure download
tasks on this screen.
My Files > Files
Shared Folders
The Files screen displays a list of shared folders that you
can access, according to your user account. Within a
shared folder, users with access to that shared folder can
create other folders and files.
Public Folders These are shared folders accessible to all
users. Disk 1 and Disk 2 are listed as PUBLIC DISK 1 (Public
Data) and PUBLIC DISK 2 (Public Data).
Private Folders These are your personal folder
and the shared folders associated with your login.
(The administrator controls folder access using the
Administration > Shared Folders screen.)
USB Storage Devices All users have access to the devices
connected to the Network Storage System.
My Files > My Downloads
Download Manager The status of the Download
Manager feature is displayed.
User Name Your login name is displayed.
Maximum Concurrent Tasks The maximum number of
tasks that can run at the same time is displayed.
For each download task, the screen lists the File Name, File
Size, Progress, Speed, and Status information.
Add Task Click this option to add a new download task. A
new screen appears.
Current Folder
The shared folder you are currently accessing is displayed.
The sub-folders available to you are listed with the
following information: Type, Name, Size, and Last Modified
date and time.
Click the folder you want to access. To view a file, click the
filename. To download a file, right-click the filename and
select Save Target as...
Create New Download Task
Click Refresh for the most up-to-date information.
Source
•• URL Enter the URL of the FTP or HTTP URL.
•• Destination Click Browse. The Folders Browser screen
appears.
Network Storage System with 2 Bays
12
Advanced Configuration
Chapter 3
My Files > Personal Info
Change your password on this screen.
Folders Browser
–– Current Folder Select the location of the shared
folder that you want to specify as the current
folder.
–– New Folder To create a new folder, enter its name,
and then click Create. Select the new folder from
the list, and its path appears in the Current Folder
field.
Click Apply to save the location. Click Close to exit this
screen.
•• The Remote Server Requires Authentication If
authentication is required to access the URL, select this
option, and complete the following:
–– User Name Enter the user name used to access
the URL.
–– Password Enter the password used to access the
URL.
NOTE: For more information about
authentication for the remote server, contact
the administrator of the remote server.
Click Save to save the new download task, or click
Cancel to clear your changes.
My Files > Personal Info
User Name Your login name is displayed.
Current Password Enter your current password.
New Password Enter your new password.
Confirm New Password Enter your new password
again.
Click Save to save your new password, or click Cancel to
clear your change.
Administration > Status
To manage the Network Storage System:
1. Click Administration Login.
2. Enter your information in the User Name and Password
fields.
3. Click OK.
The Status screen shows information about the Network
Storage System.
Start/Stop Select the appropriate download task, and
then click Start/Stop to start or stop the selected task.
Cancel If you want to delete a download task, select it,
and then click Cancel.
Refresh Click Refresh to update the on-screen status
information.
Administration > Status
Network Storage System with 2 Bays
13
Advanced Configuration
Chapter 3
Disk Status
Information about the hard drive(s) is displayed.
Internal Disks
Volume Mode The disk configuration is displayed.
Volume Status The format status of each hard drive is
displayed.
Disk 1-2, LVM, RAID 1, or RAID 0 The amount of free and
total space is displayed.
Information The Model number and Status of each hard
drive are displayed.
External Disks
Log File
Click Refresh for the most up-to-date information.
Click Clear to remove all entries. Click Close to exit this
screen and return to the Status screen.
USB Port
For each USB storage device, the Partition, File System,
Shared Folder, Total Size, and Free Size information is
displayed.
System Status
For the Network Storage System, the Server Name,
Firmware Version, Hardware Address, IP Address, Date,
Time, and Current Status information is displayed.
Administration > Users
The Users screen allows you to manage all Network Storage
System users. Linksys recommends that you create a user
account for each user, so each user has a unique login and
personal folder. (The user has automatic read/write access
to the personal folder, which uses the login name as the
folder name.)
Administration > Users
User List
Disk and System Status
Click Refresh for the most up-to-date information. Click
View Log to view a list of system activities. The Log File
screen appears.
The User List shows all existing users. (The admin and
guest users are pre-defined and cannot be deleted.)
New
Click this option to add a user account. The Create User
screen appears.
New User
•• Name Create a unique login name for the user.
Punctuation and other special characters (for example,
* / | \ ) cannot be used in the name.
Network Storage System with 2 Bays
14
Advanced Configuration
Chapter 3
•• Password Enter the password this user will use to
access the Network Storage System.
•• Verify Password Enter the password again.
•• Allow Download Manager Access If you want to
allow this user to use the Download Manager, then
select this option.
•• Allow Download Manager Access If you want to
allow this user to use the Download Manager, then
select this option.
•• Restrict Disk Quota to __ MB Select this option if you
want to set a maximum amount of disk space for this
user. Then enter the number of MB you want to allow.
NOTE: The Download Manager feature lets you
specify download tasks for the Network Storage
System. The advantage is that the Network
Storage System can run the download task
separately, without using your computer. For
example, if you order a movie online, then you
can have the Network Storage System—instead
of your computer—download the movie.
•• Restrict Disk Quota to __ MB Select this option if you
want to set a maximum amount of disk space for this
user. Then enter the number of MB you want to allow.
•• Create Personal Folder Linksys recommends that you
keep this option enabled, so each user has a personal
folder. (The user has automatic read/write access to
the personal folder, which uses the login name as the
folder name.)
User Properties
Click Save to save your changes, or click Cancel to
clear your changes.
Delete To delete a user, select the user on the User List. Then click
this option. A confirmation screen appears.
Confirm Deletion
Click OK to confirm the deletion, or click Cancel to
cancel the deletion.
New User
Another screen appears, asking if you want to delete
the user’s corresponding personal folder.
Click Save to create a new user, or click Cancel to clear
your changes.
Edit Click this option to change the settings of a user account.
The User Properties screen appears.
User Properties
Confirm Deletion of Personal Folder
Click OK to delete the personal folder, or click Cancel
to keep the personal folder and its contents.
•• Name Change the login name of the user. Punctuation
and other special characters (for example, * / | \ ) cannot
be used in the name.
•• Password Change the password this user will use to
access the Network Storage System.
•• Verify Password Enter the password again.
Network Storage System with 2 Bays
15
Advanced Configuration
Chapter 3
Administration > Shared Folders
The Shared Folders screen allows you to create and manage
shared folders. Within a shared folder, users with access to
that shared folder can create other folders and files.
Folders Browser
–– Current Folder Select the location of the shared
folder that you want to specify as the current
folder.
–– New Folder To create a new folder, enter its name,
and then click Create. Select the new folder from
the list, and its path appears in the Current Folder
field.
Administration > Shared Folders
Shared Folder List
The Shared Folder List shows all existing shared folders.
A user has access to the following:
•• Public folders accessible to all users
•• Private folders: personal folder and shared folders
specified by the administrator
•• USB storage devices accessible to all users
Share
Only users with administrative rights can create shared
folders. Click this option to create a new shared folder.
New Shared Folder
Once the shared folder is created, the location cannot be
changed.
Click Apply to save the location. Click Close to exit this
screen.
•• Display Name Enter the display name of the folder.
Punctuation and other special characters (for example,
* / | \ ) cannot be used in the name.
•• Description Enter a description of the folder.
Click Save to create a new shared folder, or click Cancel to
clear your changes. The shared folder will appear on the
My Files > Files screen of users who have access to that
shared folder.
Edit
Only users with administrative rights can edit shared
folders. To change the properties of a shared folder, select
the folder on the Shared Folder List, and then click this
option. The Shared Folder Properties screen appears.
Shared Folder Properties
Change the display name or description on this screen.
New Shared Folder
•• Location Click Browse. The Folders Browser screen
appears.
Shared Folder Properties
Network Storage System with 2 Bays
16
Advanced Configuration
Chapter 3
•• Location The location cannot be changed.
•• WINS
•• Display Name Change the display name of the folder.
•• DDNS
Punctuation and other special characters (for example,
* / | \ ) cannot be used in the name.
•• Description Change the description of the folder.
Click Save to save your changes, or click Cancel to
clear your changes.
•• Date & Time
•• E-Mail Alert
•• Scheduled Shutdown
•• Download Manager
•• UPnP
Delete
To delete a shared folder, select the shared folder on the
Shared Folder List. Then click this option. A confirmation
screen appears.
•• Options
NOTE: In most cases you do not need to change
the settings on this screen.
Confirm Deletion of Shared Folder
Click OK to confirm the deletion, or click Cancel to
cancel the deletion.
Another screen appears, asking if you want to delete
the content of the shared folder.
Administration > System Options
Confirm Deletion of Contents
Click OK to delete the content, or click Cancel to keep
the content.
Index
A list of links to the different sections of the System Options
screen is displayed. Click the link to the settings you want
to configure.
User List
To change the access rights of users, select the appropriate
shared folder. Then select No Access, Read Only, or
Read/Write for each user. All users have Read/Write access
to the shared folders of USB storage devices. The admin
user has Read/Write access to all shared folders.
Click Save to save your changes, or click Cancel to clear
all changes.
Administration > System Options
The current settings of the Network Storage System
appear on this screen. You can change any of the settings
in the following sections:
•• Identification
•• IP Address
•• DNS Server
Network Storage System with 2 Bays
17
Advanced Configuration
Chapter 3
•• Network Mask Enter the Network or Subnet Mask,
which must match the Subnet Mask of the other devices
on your network. The default is 255.255.255.0.
Gateway If you have a router on your network, enter its
IP address. The default is 192.168.1.1.
DNS Server
Obtain DNS Server Addresses from DHCP Server If
you have a router or other DHCP server on your network,
select this option.
Use Fixed DNS Server Addresses If you want to set
specific DNS settings, select this option. Then enter the
following information:
•• Primary Enter the IP address of your network’s DNS
server.
•• Backup 1-2 (Optional) Enter the IP addresses of
your network’s backup DNS servers. If you have listed
multiple DNS servers, the first available server will be
used.
WINS
Identification, IP Address, DNS Server, and WINS
Identification
Server Name Enter a different name for the Network
Storage System. Punctuation and other special characters
(for example, * / | \ ) cannot be used in the name.
Enable WINS If your network has a WINS server, select
this option to register the Network Storage System with
the WINS server.
WINS Server Enter the IP address of your WINS server.
Comment Enter a description of the Network Storage
System, such as its location.
Workgroup Enter the Workgroup name of the computers
on your network. If the Workgroup name of the Network
Storage System does not match the Workgroup name
of the computers on your network, then access to the
Network Storage System is still possible, but the Network
Storage System will not appear when you double-click
My Network Places or Network Neighborhood. (For
more information about the Workgroup name of your
computers, refer to Windows Help.)
IP Address
Obtain IP Address Automatically (DHCP Client) If
you have a router or other DHCP server automatically
assigning IP addresses, select this option.
Fixed IP Address If you want to set specific network
settings, select this option. Then enter the following
information:
•• IP Address Enter the Network Storage System’s IP
address, and make sure that it is on the same local area
network (LAN) segment as the computer running the
Setup Wizard.
Network Storage System with 2 Bays
DDNS, Date & Time, and E-Mail Alert
18
Advanced Configuration
Chapter 3
DDNS
•• NTP Server To use a pre-selected NTP server, select
The Network Storage System offers a Dynamic Domain
Name System (DDNS) feature. DDNS lets you assign a fixed
host and domain name to a dynamic Internet IP address,
so you can locate the Network Storage System without
knowing its dynamic Internet IP address.
For example, assign the Network Storage System the fixed
host and domain name of www.mystorage.com. When
you travel, you can find the Network Storage System at
www.mystorage.com (the DDNS service provider keeps
track of the dynamic Internet IP address of the Network
Storage System.)
Before you can use this feature, you need to sign up
for DDNS service with TZO, a DDNS service provider at
www.tzo.com. Click Sign up for a TZO DDNS account.
NOTE: To use the DDNS feature of the Network
Storage System, configure port forwarding on
your network router. For more information,
refer to the router’s documentation.
Enable TZO DDNS Select this option to use the DDNS
feature.
E-Mail Address, TZO Key, and Domain Name Enter the
settings of the account you set up with TZO.
Update Period Select how often you want your Internet
IP address to be updated with TZO.
Update Now To manually trigger an immediate IP
address update, click this option.
Choose and select an NTP server from the drop-down
menu.
To manually select an NTP server, select Specify and
enter the URL or IP address of an NTP server.
•• NTP Status The status of the NTP server is displayed.
•• Synchronize with NTP Server Select how often you
want the Network Storage System to synchronize
with the NTP server. Then enter the time you want the
synchronization to begin.
•• Synchronize Now If you want the Network Storage
System to synchronize with the NTP server at this time,
click this option.
E-Mail Alert
Send E-Mail Alerts when Problems are Detected Select
this option if you want the Network Storage System to
send e-mails sent when it is experiencing problems. (The
problem will be described in the e-mail.)
E-Mail Address (1-3) Enter the e-mail addresses that
should receive e-mail alerts.
From Address Enter the return e-mail address you want
used in the e-mails. (This can be a dummy address.)
Subject Enter the subject heading you want the e-mails
to use.
SMTP Port Enter the SMTP port number that you want
the e-mail alerts to use. If you are not sure which SMTP
port number to use, then keep the default, 25.
Date & Time
Time Zone Select your local time zone.
Enable Daylight Saving Click this option if your location
uses daylight saving.
Change System Time as Following To manually set the
date and time of the Network Storage System, select this
option. Then select the date and time.
•• Date Configure today’s date (Month, Day, Year). The
Network Storage System will set its own calendar
according to the date you provide.
•• Time Enter the current time (hour, minute, am or pm).
The Network Storage System will set its own clock
according to the time you provide. Remember that the
time you enter is not saved until you click Save.
Enable NTP (Network Time Protocol) NTP servers are
frequently used to synchronize clocks. To use an NTP
server, select this option. Then configure the following
settings:
Network Storage System with 2 Bays
Scheduled Shutdown, Download Manager, UPnP, and Options
19
Chapter 3
Scheduled Shutdown
Shutdown Select the day and time you want the
automatic shutdown to occur. Keep the default, Never, if
you want to manually initiate the shutdown. (When the
Network Storage System is shut down, you will have to
manually power on the Network Storage System.)
Shutdown Now Click this option to shut down the
Network Storage System immediately.
Download Manager
Use this section to enable and configure the Download
Manager feature, which lets you specify download tasks
for the Network Storage System. The advantage is that
the Network Storage System can run the download task
separately, without using your computer. For example, if
you order a movie online, then you can have the Network
Storage System—instead of your computer—download
the movie.
Advanced Configuration
Convert Failed Logins to “guest” Logins (Windows
Networks) If you want to allow all Windows users to
access the Network Storage System with guest access
rights, then select this feature. By default, the guest user
has Read/Write access to public data on each disk (this
cannot be changed by the administrator).
Enable FTP Server If you want to allow use of an FTP
server, then select this option.
•• Port Number Select the port number for the FTP
server. The default is 21.
•• Language Support for Clients Select the appropriate
language from the drop-down menu.
Allow Anonymous FTP Login (“guest” rights) If you
want to allow FTP users to log in anonymously, then select
this option. Any FTP user can use the word “Anonymous” as
the user name, and any combination of letters or numbers
can be used as the password.
Speed Limit Per Task Enter the maximum download
speed of each task. If you keep the default, 0, then there
is no speed limit.
HTTP (Web Browser) Port Number Enter the port
number used for HTTP connections to the Network
Storage System. This will be used for remote access of the
Network Storage System. The default is 80. If you want
to change this number, then you should use a number
greater than 1024 (8080 is often used). Also, if the port is
not 80, you must specify the port in your web browser in
order to connect. To do this, add a colon (“:”) and the port
number after the address, such as http://192.168.1.77:808
0. (This example assumes the Network Storage System’s IP
address is 192.168.1.77, and the port number is 8080.)
Language Support for URLs Select the appropriate
language from the drop-down menu.
Click Save to save your changes, or click Cancel to clear
all changes.
Enable Schedule Select this option if you want the
Download Manager to run only during the specified time
period. If this option is not selected, then the Download
Manager always runs.
Click Reset to Default to reset the settings on the System
Options screen to the factory defaults.
Enable Download Manager Select this option to enable
the Download Manager feature. Users with Download
Manager access can schedule download tasks through
the My Files > My Downloads screen.
Maximum Concurrent Tasks Select the maximum
number of tasks that can run at the same time.
•• Day Select Every Day, or select a specific day of the
week.
•• Time Select the hours during which you want the
Download Manager to run.
Firmware Upgrade
Use this screen to upgrade the firmware of the Network
Storage System. You can also back up or restore its
configuration file, which includes the settings of the
Network Storage System.
UPnP
Enable UPnP Support Select this option if you want the
Network Storage System to broadcast its availability to
users and have its own desktop icon on computers that
support UPnP (such as Windows Vista or XP).
Options
Enable Guest Logins If you want to allow users to use
the word “guest” as a login name, then select Enable Guest
Logins.
Administration > Firmware Upgrade
Network Storage System with 2 Bays
20
Advanced Configuration
Chapter 3
Current Firmware
Use this section to search for updated firmware.
Restore Click Restore to restore a previously saved
configuration file. The Restore Configuration File screen
appears.
Current Firmware Version The firmware version of the
Network Storage System is displayed.
Check for Upgrade Click this option to visit the Linksys
website, www.linksys.com, and check for updated
firmware. Follow the on-screen instructions. After you
have downloaded the new firmware file, extract it on your
computer. Then proceed to the “Upgrade” section when
you are ready to upgrade the firmware.
Upgrade
Use this section to proceed with the firmware upgrade.
Restore Configuration File
Upgrade File Click Browse to select the extracted
firmware file.
•• Select File Click Browse to select the configuration
Click Start Upgrade to begin the firmware upgrade. Then
follow the on-screen instructions.
•• Options Select
file on your computer.
the information you want to
restore: System Options, Users, Shared Folders,
and/or Utility Settings. Select All Settings to restore
all configuration information except for the disk
configuration setting, which cannot be restored.
•• Restore Click this option to restore the previously
saved settings you selected in the Options section.
•• Restore to Default Click this option to reset the
settings you selected in the Options section to their
factory defaults. (Custom settings will be deleted.)
•• Cancel Click this option to exit this screen without
making any changes.
Current Firmware, Upgrade, and Configuration Backup
Configuration Backup
Back Up Click Back Up to download the current
configuration file onto your computer. The File Download
screen appears.
Media Server
If you use a media adapter to send content to your
entertainment system, then you can use the Network
Storage System as a media server.
The Network Storage System can be located by compatible
media adapters using the UPnP AV standard. Media
content on the Network Storage System can then be
accessed and played by the media adapters.
Configure the Network Storage System as a media server
on the Media Server screen.
File Download
Click Save to save the configuration file on your
computer, and then follow the on-screen instructions.
Click Cancel to cancel the file download.
Network Storage System with 2 Bays
21
Advanced Configuration
Chapter 3
Directory The path and name of the selected folder are
displayed.
All If you wish, each directory can be limited to a specific
media type. The default setting, All, scans for all content
types. Select the appropriate media type(s): All, Music,
Picture, or Video.
Content Scan
Specify the scan behavior of the media server.
Administration > Media Server
Media Server
Enable Media Server If enabled, the Network Storage
System can be located by compatible media adapters
using the UPnP AV standard. Media content on the
Network Storage System can then be accessed and played
by the media adapters.
Server Name Enter the name of the media server as it
should be displayed on client devices.
Content Directory
By default, the root directory of each drive is displayed
when the Media Server feature is enabled.
Continuous Scan Select this option if you want the
media server to automatically rescan media files when
they change.
Scheduled Scan in __ Minutes Select this option if you
want the media server to scan media files at the specified
interval. Then enter the number of minutes in each
interval.
Scan Now If you want the media server to scan media
files at this time, click this option.
Click Save to save your changes, or click Cancel to clear
all changes.
Disk Utility
Use this screen to format or maintain the installed
drive(s).
You can specify up to four directories that the media server
should scan for media content. Select the appropriate
check box to select or deselect a directory.
Browse Click Browse. The Folders Browser screen
appears.
Administration > Disk Utility
Format Disk
Use this option to partition and format a newly installed
drive if you did not run the Setup Wizard when you
physically installed the new drive.
Folders Browser
•• Current Folder Select the location of the shared
folder that you want to specify as the current folder.
•• New Folder To create a new folder, enter its name,
NOTE: If you physically install a new drive
without running the Setup Wizard, then it will
not be formatted. You must manually format
the new drive using the Format Disk feature.
and then click Create. Select the new folder from the
list, and its path appears in the Current Folder field.
Click Apply to save the location. Click Close to exit this
screen.
Network Storage System with 2 Bays
22
Advanced Configuration
Chapter 3
WARNING: Before you format drive(s), back
up pre-existing data because all data on
your drive(s) will be erased when they are
formatted.
remaining memory, and additional partitions cannot
be created.
Click Apply to save your changes, or click Cancel to
clear all changes.
NOTE: The settings on this screen will vary
depending on the disk configuration. A single
drive is listed as Disk 1. Two drives are listed
as Disk 1 and 2 when they are configured as
Separate Disks. Two drives are listed as LVM
when they are configured as JBOD/LVM.
Two drives are listed as RAID 1 when they are
configured as RAID 1 (Mirroring). The drives are
listed as RAID 0 when they are configured as
RAID 0 (Striping).
Disk 1-2, LVM, RAID 1, or RAID 0 The status of the drive
is displayed. If the drive is not formatted, click Format. A
confirmation screen appears.
Format Disk, Scandisk, S.M.A.R.T., Standby, and Disk Full
Scandisk
Confirm Reformatting
Click OK to confirm the formatting. Click Cancel to
cancel the formatting.
USB 1-2 The status of the drive is displayed. If the drive is
not formatted, click Format. The Partition & Format screen
appears.
The Scandisk program checks the drive(s) for errors and
corrects errors when possible. It will run automatically
if an error is detected, such as a shutdown due to an
unexpected loss of power. While the Scandisk program
is running, you will not be able to access the drive being
scanned.
Disk 1-2, LVM, RAID 1, or RAID 0 The Scandisk status
of the drive is displayed. Click Start/Stop to begin the
Scandisk program. A confirmation screen appears.
Confirm Scandisk
Partition & Format
•• Model The name of the USB drive is displayed.
•• Total Disk Size The number of MB on the drive is
displayed.
•• New Partitions You can specify up to four partitions.
For each selected partition, specify its size in MB, or
select Fill Up Free Space. If the Fill Up Free Space
option is selected, then the partition occupies all
Network Storage System with 2 Bays
Click OK to confirm running the Scandisk program.
Click Cancel to cancel running the Scandisk program.
If you need to access the drive while the Scandisk program
is running, click Start/Stop to stop the Scandisk program.
Run Scandisk You can schedule the Scandisk program
to run on a regular schedule. Select the day and time you
want the Scandisk program to run. Keep the default, Never,
if you want to manually initiate the Scandisk program.
S.M.A.R.T.
23
Advanced Configuration
Chapter 3
Self-Monitoring Analysis and Reporting Technology
(S.M.A.R.T.) can warn you of impending drive problems
before the drive fails.
Disk 1-2, LVM, RAID 1, or RAID 0 The S.M.A.R.T. status
of the drive is displayed. Click Test Now to begin the
S.M.A.R.T. check.
Standby
The drive(s) go into standby mode after the specified
period of idle time. During standby mode, the Network
Storage System uses less energy and emits less heat. If the
fan powers off, then noise is also reduced.
Set Hard Disk to Standby Mode after Keep the default,
Idle 30 minutes, if you want the period of idle time to be
30 minutes. Select Idle 10 minutes, if you want the period
of idle time to be 10 minutes.
Power off the fan after All Hard Drives are in Standby
Mode The fan of the Network Storage System powers
off when the drive(s) are idle for a period of time. Keep
the default, 20 Minutes, if you want the fan to power off
after 20 minutes of inactivity. Select 40 Minutes if you
want the fan to power off after 40 minutes of inactivity.
Select 10 Minutes if you want the fan to power off after
10 minutes of inactivity. Select Never if you want the fan
to always be powered on as long as the Network Storage
System is powered on.
Disk Log
Click Refresh to update the on-screen information.
Click Close to exit this window.
Disk Configuration
Use this screen to change the configuration of your
installed drive(s), which are initially configured during the
Setup Wizard. If you change the configuration, then the
drive(s) must be reformatted; make sure you back up all
data on the drive(s) before they are reformatted.
NOTE: During standby mode, the hard drive(s)
and fan may activate for a capacity check or
other network activity. When there is no more
activity, the hard drive(s) will return to standby
mode, and then the fan will stop.
Administration > Disk Configuration
Disk Full
When drive capacity is nearly full, the Network Storage
System will log it and send an e-mail alert.
Send E-Mail Alert when Disk Available Capacity is Less
than Keep the default, 2%, if you want to be alerted
when less than 2% of the total drive capacity is available.
Select 2GB, if you want to be alerted when less than 2 GB
is available. Select 5GB, if you want to be alerted when
less than 5 GB is available. (After you have finished making
changes to the Disk Utility screen, click System Options to
enter e-mail address(es) in the E-Mail Alert section.)
Click Save to save your changes, or click Cancel to clear all
changes. (Clicking Cancel does not affect any operations
in progress, including drive formatting, the Scandisk
program, and the S.M.A.R.T. check.)
Click Disk Log to view a list of disk activities, including
Scandisk and S.M.A.R.T. results. The Disk Log screen
appears.
Network Storage System with 2 Bays
Volume Mode
Select the appropriate configuration for your drive usage.
WARNING: Before you format drive(s), back
up pre-existing data because all data on
your drive(s) will be erased when they are
formatted.
Maximum Storage
Separate Disks Disk 1 and Disk 2 work separately.
Multiple Disks (JBOD/LVM) Disk 1 and Disk 2 are bound
into one logical volume. Total capacity is equal to the
capacity of the existing disk(s). If this configuration is
selected with only one disk installed, then the second disk
will be configured to extend the capacity of the logical
volume when it is installed.
24
Chapter 3
Advanced Configuration
Maximum Security
Mirroring (RAID 1) Disk 1 is mirrored into Disk 2. Total
capacity is equal to the capacity of the smaller disk.
NOTE: Mirroring (RAID 1) and Striping (RAID 0)
require two hard drives.
Maximum Speed
Striping (RAID 0) Disk 1 and Disk 2 are striped into one
logical volume. Total capacity is equal to two times the
smaller capacity of the two disks.
Click Save to save your change.
Network Storage System with 2 Bays
25
Use
Chapter 4
Chapter 4: Use
This chapter describes access rights, access methods, and
use of USB storage devices.
WARNING: Do not block the air vents, and do
not stack devices on top of the Network Storage
System; otherwise, overheating can occur.
(Air vents are located on the sides of the
Network Storage System. Keep the area around
the Network Storage System clear.)
Web Access
To access the Network Storage System from any computer
using a web browser, follow these instructions:
1. Open your web browser.
2. In the Address field, enter http://<IP_address_of_
the_Network_Storage_System>.
If you do not know its IP address, then run the Setup
Wizard. Click the Click Here to Start button. Then click
Advanced Setup. Select the appropriate Network
Storage System, and its IP address will be displayed. (For
more information, refer to “Chapter 2: Configuration
Using the Setup Wizard”.)
Access to the Network Storage System
3. The web-based utility appears.
All Windows users can access the Network Storage
System with guest access rights. Specifically, guest users
can access any shared folders with access rights for guest
users and any connected USB storage devices.
Access My Files Click this option to access folders or
change your password.
Linksys recommends that you create a user account
for each user, so each user will have a unique login and
personal folder. (The login name will be used as the name
of the personal folder.)
On the homepage, you have two options:
Administration Login Click this option to manage the
Network Storage System through the web-based utility.
For more information, refer to “Chapter 3: Advanced
Configuration”.
How to Access the Network Storage System
There are two ways to access the Network Storage System.
The first way uses the My Network Places or Network
Neighborhood icon on the desktop of your Windows
operating system. The second way uses your web
browser.
Access is controlled by login name and password.
Windows Access
To access the Network Storage System from a Windowsbased computer, follow these instructions:
1. Double-click the My Network Places or Network
Neighborhood icon.
2. Double-click the Network Storage System. If you
do not see it, then change the Workgroup of the
Network Storage System to match the Workgroup
of your computer (refer to the Administration >
Systems Options section of “Chapter 3: Advanced
Configuration”).
Home Screen
My Files
Any user has access to the My Files section. To access
folders or change your password:
1. Click Access My Files.
2. Enter your information in the User name and Password
fields.
3. Click OK.
3. If prompted, enter your login name and password. If
you do not have a login, enter guest for the user name.
Leave the Password field blank.
4. The Files screen appears. You have two options
available, Files and Personal Info, in the My Files
column.
If you want to map a shared folder to a drive letter on your
computer, refer to Windows Help for details, or use the
Network Drive Mapping Utility (refer to the section, “How
to Use the Network Drive Mapping Utility”).
If the Download Manager feature has been enabled
through the Administration > System Options screen
and your login has Download Manager access, then
the My Downloads option will also be displayed.
Network Storage System with 2 Bays
26
Use
Chapter 4
NOTE: The Download Manager feature lets you
specify download tasks for the Network Storage
System. The advantage is that the Network
Storage System can run the download task
separately, without using your computer. For
example, if you order a movie online, then you
can have the Network Storage System—instead
of your computer—download the movie.
My Files > Files
The Files screen displays a list of folders that you can
access, according to your user account.
My Files > My Downloads
Download Manager The status of the Download
Manager feature is displayed.
User Name Your login name is displayed.
Maximum Concurrent Tasks The maximum number of
tasks that can run at the same time is displayed.
For each download task, the screen lists the File Name, File
Size, Progress, Speed, and Status information.
Add Task Click this option to add a new download task to
the Network Storage System. A new screen appears.
My Files > Files
Public Folders These are shared folders accessible to
everyone. Disk 1 and Disk 2 are listed as PUBLIC DISK 1
(Public Data) and PUBLIC DISK 2 (Public Data).
Private Folders These are your personal folder and the
folders associated with your login.
USB Storage Devices All users have access to the devices
connected to the Network Storage System. USB devices
can be used to add or move content.
Create New Download Task
Click the folder you want to access. To view a file, click the
filename. To download a file, right-click the filename and
select Save Target as...
Source
Click Refresh for the most up-to-date information about
the folders.
•• Destination Click Browse. The Folders Browser screen
My Files > My Downloads
•• URL Enter the URL of the FTP or HTTP URL.
appears.
If the Download Manager feature has been enabled
through the Administration > System Options screen and
your login has Download Manager access, then the My
Downloads screen will be available.
Network Storage System with 2 Bays
27
Use
Chapter 4
4. Enter your new password in the New Password and
Confirm New Password fields.
5. Click Save to save your new password, or click Cancel
to clear your change.
Folders Browser
–– Current Folder Select the location of the shared
folder that you want to specify as the current
folder.
–– New Folder To create a new folder, enter its name,
and then click Create. Select the new folder from
the list, and its path appears in the Current Folder
field.
Click Apply to save the location. Click Close to exit this
screen.
•• The Remote Server Requires Authentication If
authentication is required to access the URL, select this
feature, and complete the following:
–– User Name Enter the user name used to access
the URL.
–– Password Enter the password used to access the
URL.
NOTE: For more information about
authentication for the remote server, contact
the administrator of the remote server.
Click Save to save the new download task, or click
Cancel to clear your changes.
Start/Stop Select the appropriate download task, and
then click Start/Stop to start or stop the selected task.
Cancel If you want to delete a download task, select it, and
then click Cancel. (Completed tasks are not automatically
deleted, so you will have to manually delete them.)
Refresh Click Refresh to update the on-screen status
information.
My Files > Personal Info
USB Storage Devices
You can connect USB storage devices to the USB ports
at any time. User accounts do not apply to USB storage
devices. All folders and files on those devices are available
to all users while the USB storage devices are connected
to the Network Storage System.
For convenience, you can use the Network Drive Mapping
Utility to map a connected USB storage device as a
network drive on your computer. You can also use the
utility to remove the device.
How to Add a USB Storage Device
To add a USB storage device, connect the device to the
USB 1 or USB 2 port. When the corresponding USB LED
lights up, the USB device is available for use.
How to Remove a USB Storage Device
To safely remove a USB storage device:
1. Linksys recommends that you wait until the device is
not being used, when its USB LED is continuously lit.
Press the USB 1 button to eject the device from the
USB 1 port, or press the USB 2 button to eject the
device from the USB 2 port.
My Files > Personal Info
Any user can change the password to the My Files section.
To change your password:
1. Click Personal Info.
2. Enter your login name in the User Name field.
3. Enter your current password in the Current Password
field.
Network Storage System with 2 Bays
Back Panel
28
Use
Chapter 4
2. After the Network Storage System beeps once and
the appropriate USB LED powers off, disconnect the
device.
3. The Shared Folder Mapping screen appears. Select the
appropriate Network Storage System.
You can also use the Network Drive Mapping Utility to
remove the device. This is explained in the following
section, “How to Use the Network Drive Mapping Utility”.
How to Use the Network Drive Mapping
Utility
Any user can use the Network Drive Mapping Utility to do
the following:
•• Map a shared folder to a drive letter on a computer
Shared Folder Mapping
•• Map a USB storage device to a drive letter on a
computer
•• Safely remove a USB storage device from the Network
Storage System
(If you do not have this utility installed, you can still use
Windows to manually map a shared folder or USB storage
device to a drive letter. Refer to Windows Help for more
information.)
4. Select the appropriate shared folder. If you do not see
the folder you want, click Refresh.
5. Keep the default drive letter, or select a different letter
from the drop-down menu. Then click Map.
6. The shared folder automatically opens, and a new
window appears to notify you that the shared folder
has been mapped. Click OK.
If the utility has not been installed, run the Setup Wizard.
Refer to “Chapter 2: Configuration Using the Setup
Wizard”.
System Tray Icon
While the utility is running, its icon is displayed in the
system tray, which is located in the lower right corner of
your desktop.
Shared Folder Mapped
7. On the Shared Folder Mapping screen, click Close.
8. Double-click My Computer. The shared folder is
displayed as a network drive.
How to Map a USB Storage Device
System Tray Icon
If the utility is not running, proceed to the “Desktop Icon”
or “Program Folder” section for information on how to
activate the utility.
How to Map a Shared Folder
1. Right-click the icon in the system tray.
2. Click USB Device Mapping.
3. The Map Network Drive screen appears. Keep the
default drive letter or enter a different letter in the
Drive field.
1. Right-click the system tray icon.
Map Network Drive
Right-Click Icon
2. Click Shared Folder Mapping.
4. Keep the default, Reconnect at logon, if you want the
USB storage device to re-connect automatically.
5. Click OK.
6. Double-click My Computer. The USB storage device
displays as a network drive.
Network Storage System with 2 Bays
29
Use
Chapter 4
How to Remove a USB Storage Device
Program Folder
1. Right-click the icon in the system tray.
2. Click Safely Remove USB Device.
If the utility is inactive, its icon is not displayed in the
system tray.
3. Select the appropriate USB storage device, and click
Eject. If you do not see the device you want, click
Refresh.
If you need to map a shared folder or USB storage device,
or you need to remove a USB storage device, then proceed
to the “Activate the Utility” section.
Activate the Utility
1. Click Start.
2. Select All Programs.
3. Select Network Drive Mapping Utility.
4. Click Network Drive Mapping Utility.
Program Folder
The utility runs, and its icon appears in the system tray.
Refer to the section, “System Tray Icon”, for details.
Uninstall the Utility
Select USB Device
4. A message notifies you when the device can be
removed. Click OK.
To remove the utility from your computer:
1. Click Start.
2. Select All Programs.
3. Select Network Drive Mapping Utility.
4. Click Uninstall.
USB Device Can Be Removed
5. A confirmation screen appears. Click Yes to confirm
removal of the utility, or click No to cancel removal of
the utility.
To exit the utility, right-click the icon in the system. Then
click Exit.
Desktop Icon
If the utility is inactive, its icon is not displayed in the
system tray.
If you need to map a shared folder or USB storage device,
or you need to remove a USB storage device, then doubleclick the desktop icon.
Desktop Icon
The utility runs, and its icon appears in the system tray.
Refer to the section, “System Tray Icon”, for details.
Network Storage System with 2 Bays
30
Appendix A
Appendix A:
Troubleshooting
The Setup Wizard does not detect any Network Storage
Systems.
Follow these instructions until your problem is solved:
1. Make sure the Network Storage System is powered
on.
2. Check the cable connections of the Network Storage
System.
3. Make sure your computer and the Network Storage
System are on the same network segment. (If you do
not have a router, then skip this step.)
4. In all Windows operating systems, the TCP/IP protocol
is installed by default. If you have uninstalled the
TCP/IP protocol, refer to Windows Help for instructions
on how to re-install the TCP/IP protocol.
5. During the Setup Wizard, select Automatically obtain
an IP address (DHCP recommended) if your local
network has a DHCP server (usually a router) assigning
IP addresses, or select Set IP configuration manually
if your local network does not have a DHCP server.
If you selected Set IP configuration manually, then
complete the IP Address, Subnet Mask, and Gateway
fields. The range commonly used for IP addresses is
192.168.1.1 to 192.168.1.254, with a Subnet Mask of
255.255.255.0. (Each device on your local network
requires a unique IP address and the same Subnet
Mask.)
You cannot access the web-based utility of the Network
Storage System.
Check the IP address of the Network Storage System. By
default, the Network Storage System uses a dynamic IP
address assigned by your DHCP server (usually a router);
run the Setup Wizard or check the router’s utility for the
current IP address of the Network Storage System. If your
network does not have a DHCP server, run the Setup
Wizard to assign an appropriate static IP address to the
Network Storage System (make sure this static IP address
is within the IP address range used by your network).
You have configured the Network Storage System is
configured, but you do not see it in My Network Places or
Network Neighborhood.
Change the Workgroup of the Network Storage System
to match the Workgroup of your computer (refer to the
Administration > System Options section of “Chapter 3:
Advanced Configuration”). If this does not work, follow
these instructions until your problem is solved:
Network Storage System with 2 Bays
Troubleshooting
1. Click Start. Click Search. Click Computers or people.
Click A computer on the network. Enter the name of
the Network Storage System, and click Search.
2. In all Windows operating systems, the TCP/IP protocol
is installed by default. If you have uninstalled the
TCP/IP protocol, refer to Windows Help for instructions
on how to re-install the TCP/IP protocol.
3. Click Start. Select Control Panel. Right-click Network
Connections. Click Open. Click Advanced. Click
Advanced Settings. Select the Local Area Connection
you are using. In the Bindings for Local Area Connection
section, make sure these two settings, File and Printer
Sharing for Microsoft Networks and Client for Microsoft
Networks, are selected. If not, select them. Then click
OK.
4. If your local network has a DHCP server (usually a
router), run the Setup Wizard and make sure the
Network Storage System is on the same network
segment as your computer. (If you do not have a router,
then skip this step.)
5. If your local network does not have a DHCP server
(usually a router), make sure the IP address of your
computer is compatible with the IP address of the
Network Storage System. The range commonly used
for IP addresses is 192.168.1.1 to 192.168.1.254, with
a Subnet Mask of 255.255.255.0. (Each device on your
local network requires a unique IP address and the
same Subnet Mask.)
When you click the Network Storage System icon in My
Network Places or Network Neighborhood, you are
prompted for a password.
One of the following situations may have occurred:
•• The Network Storage System recognizes the Windows
user name you used to log into your computer, but it
does not recognize the password. At the prompt, enter
your password for the Network Storage System. (Later
you can change your Windows password to make it
match the Network Storage System password.)
•• The Network Storage System does not recognize
the Windows user name you used to log into your
computer, so it recognizes you as a guest with guest
access rights. Use the Setup Wizard or web-based
utility of the Network Storage system to create an
account for your Windows user name.
•• You do NOT have permission to access the Network
Storage System. Use the Setup Wizard or web-based
utility to assign the appropriate level of access to your
account.
31
Appendix A
NOTE: Windows uses the computer name as
the default user name on the login screen. To
create a new Windows user name, enter a new
user name and password on the login screen.
Troubleshooting
WEB: If your questions are not addressed here,
refer to the Linksys website, www.linksys.com
You connected the USB flash disk to the Network
Storage System and mapped it as a drive. Now you
have disconnected the USB flash disk from the Network
Storage System and connected it directly to your
computer. The USB flash disk reads as a disconnected
network drive.
Windows maps both the network drive (USB flash disk
connected through the Network Storage System) and
local drive (USB flash disk connected directly to the
computer) to the same drive letter. You can still doubleclick the disconnected network drive to access the USB
flash disk. You can also follow these instructions to map
the local USB flash disk to a different drive letter:
1. Right-click My Computer.
2. Click Manage.
3. Click Disk Management.
4. Right-click the USB flash disk.
5. Click Change Drive Letter and Paths.
6. Select a different drive letter, and click OK.
7. Click OK to confirm the change.
8. Click OK again. If you wish, you can reassign the former
drive letter after the computer is restarted.
You were not able to map a shared folder using the
Network Drive Mapping Utility.
Your computer is not able to locate the Network Storage
System by using its device name, so instead you have to
use its IP address and manually map a shared folder in
Windows. (If the Network Storage System uses a dynamic
IP address assigned by your network router, then run the
Setup Wizard or check the router’s utility for the current
IP address of the Network Storage System.) Follow these
instructions:
1. Right-click the My Network Places icon.
2. Click Map Network Drive.
3. On the Map Network Drive screen, enter the folder
location using the IP address, \\<IP_address_of_
Network_Storage_System\<folder_name>
(for
example, \\192.168.1.100\holidaypictures), instead of
the device name.
4. Click different user name.
5. The Connect As... screen appears. Enter your user name
and password. Click OK.
6. On the Map Network Drive screen, click Finish.
Network Storage System with 2 Bays
32
Specifications
Appendix B
Appendix B:
Specifications
Model
NAS200
Standards
IEEE 802.3, IEEE 802.3u
Ports
Power, Ethernet, USB 1,
USB 2
Buttons
Power, USB 1, USB 2,
RESET, BACK UP
LEDs
Power, Ethernet, Disk (Act,
Full, 1, 2), USB 1, USB 2
Cabling Type
UTP CAT5 or Better
Security Features
User Name and Password
for Both System
Administration and
File Access
Environmental
Dimensions
6.69" x 4.49" x 7.68"
(170 x 114 x 195 mm)
Weight
1.97 lb (893 g)
Power
12V DC, 5A, Switching,
100-240V AC, 50-60Hz,
Power Adapter Provided
Certification
FCC, CE
Operating Temp.
41 to 104ºF (5 to 40ºC)
Storage Temp.
14 to 140ºF (–10 to 60ºC)
Operating Humidity
10 to 80% Noncondensing
Storage Humidity
5 to 90% Noncondensing
Network Storage System with 2 Bays
33
Appendix C
Appendix C:
Warranty Information
Limited Warranty
Linksys warrants this Linksys hardware product against
defects in materials and workmanship under normal
use for the Warranty Period, which begins on the date of
purchase by the original end-user purchaser and lasts for
the period specified below:
•• One (1) year for new product
•• Ninety (90) days for refurbished product
This limited warranty is non-transferable and extends only
to the original end-user purchaser. Your exclusive remedy
and Linksys’ entire liability under this limited warranty
will be for Linksys, at its option, to (a) repair the product
with new or refurbished parts, (b) replace the product
with a reasonably available equivalent new or refurbished
Linksys product, or (c) refund the purchase price of the
product less any rebates. Any repaired or replacement
products will be warranted for the remainder of the
original Warranty Period or thirty (30) days, whichever is
longer. All products and parts that are replaced become
the property of Linksys.
Exclusions and Limitations
This limited warranty does not apply if: (a) the product
assembly seal has been removed or damaged, (b) the
product has been altered or modified, except by Linksys, (c)
the product damage was caused by use with non‑Linksys
products, (d) the product has not been installed, operated,
repaired, or maintained in accordance with instructions
supplied by Linksys, (e) the product has been subjected to
abnormal physical or electrical stress, misuse, negligence,
or accident, (f ) the serial number on the Product has been
altered, defaced, or removed, or (g) the product is supplied
or licensed for beta, evaluation, testing or demonstration
purposes for which Linksys does not charge a purchase
price or license fee.
ALL SOFTWARE PROVIDED BY LINKSYS WITH THE
PRODUCT, WHETHER FACTORY LOADED ON THE
PRODUCT OR CONTAINED ON MEDIA ACCOMPANYING
THE PRODUCT, IS PROVIDED “AS IS” WITHOUT WARRANTY
OF ANY KIND. Without limiting the foregoing, Linksys does
not warrant that the operation of the product or software
will be uninterrupted or error free. Also, due to the
continual development of new techniques for intruding
upon and attacking networks, Linksys does not warrant
that the product, software or any equipment, system or
network on which the product or software is used will be
free of vulnerability to intrusion or attack. The product
may include or be bundled with third party software or
Network Storage System with 2 Bays
Warranty Information
service offerings. This limited warranty shall not apply to
such third party software or service offerings. This limited
warranty does not guarantee any continued availability
of a third party’s service for which this product’s use or
operation may require.
TO THE EXTENT NOT PROHIBITED BY LAW, ALL IMPLIED
WARRANTIES AND CONDITIONS OF MERCHANTABILITY,
SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED TO THE DURATION OF THE
WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED
CONDITIONS, REPRESENTATIONS AND WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED.
Some jurisdictions do not allow limitations on how long
an implied warranty lasts, so the above limitation may not
apply to you. This limited warranty gives you specific legal
rights, and you may also have other rights which vary by
jurisdiction.
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT
WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE
OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,
INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE
THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING
OUT OF OR RELATED TO THE USE OF OR INABILITY TO
USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN
IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY
EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT.
The foregoing limitations will apply even if any warranty
or remedy provided under this limited warranty fails of
its essential purpose. Some jurisdictions do not allow
the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not
apply to you.
Obtaining Warranty Service
If you have a question about your product or experience a
problem with it, please go to www.linksys.com/support
where you will find a variety of online support tools and
information to assist you with your product. If the product
proves defective during the Warranty Period, contact
Linksys Technical Support for instructions on how to
obtain warranty service. The telephone number for Linksys
Technical Support in your area can be found in the product
User Guide and at www.linksys.com. Have your product
serial number and proof of purchase on hand when calling.
A DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED
TO PROCESS WARRANTY CLAIMS. If you are requested to
return your product, you will be given a Return Materials
Authorization (RMA) number. You are responsible for
properly packaging and shipping your product to Linksys
at your cost and risk. You must include the RMA number
and a copy of your dated proof of original purchase when
returning your product. Products received without a RMA
number and dated proof of original purchase will be
34
Appendix C
Warranty Information
rejected. Do not include any other items with the product
you are returning to Linksys. Defective product covered
by this limited warranty will be repaired or replaced and
returned to you without charge. Customers outside of
the United States of America and Canada are responsible
for all shipping and handling charges, custom duties,
VAT and other associated taxes and charges. Repairs or
replacements not covered under this limited warranty will
be subject to charge at Linksys’ then-current rates.
Technical Support
This limited warranty is neither a service nor a support
contract. Information about Linksys’ current technical
support offerings and policies (including any fees for
support services) can be found at: www.linksys.com/support.
This limited warranty is governed by the laws of the
jurisdiction in which the Product was purchased by you.
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,
CA 92623.
Network Storage System with 2 Bays
35
Appendix D
Appendix D:
Regulatory Information
FCC Statement
This product has been tested and complies with the
specifications for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which is found by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
Regulatory Information
Avis d’Industrie Canada
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
Le fonctionnement est soumis aux conditions suivantes :
1. Ce périphérique ne doit pas causer d’interférences;
2. Ce périphérique doit accepter toutes les interférences
reçues, y compris celles qui risquent d’entraîner un
fonctionnement indésirable.
•• Reorient or relocate the receiving antenna
•• Increase the separation between the equipment or
devices
•• Connect the equipment to an outlet other than the
receiver’s
•• Consult a dealer or an experienced radio/TV technician
for assistance
Safety Notices
•• Caution: To reduce the risk of fire, use only No.26 AWG
or larger telecommunication line cord.
•• Do not use this product near water, for example, in a
wet basement or near a swimming pool.
•• Avoid using this product during an electrical storm.
There may be a remote risk of electric shock from
lightning.
WARNING: This product contains lead, known
to the State of California to cause cancer, and
birth defects or other reproductive harm. Wash
hands after handling.
Industry Canada Statement
This Class B digital apparatus complies with Canadian
ICES-003.
Operation is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including
interference that may cause undesired operation of
the device.
Network Storage System with 2 Bays
36
Appendix D
User Information for Consumer Products
Covered by EU Directive 2002/96/EC on
Waste Electric and Electronic Equipment
(WEEE)
This document contains important information for users
with regards to the proper disposal and recycling of
Linksys products. Consumers are required to comply with
this notice for all electronic products bearing the following
symbol:
Regulatory Information
Čeština (Czech) - Informace o ochraně životního
prostředí pro zákazníky v zemích Evropské unie
Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené
tímto symbolem na produktu anebo na obalu bylo likvidováno
s netříděným komunálním odpadem. Tento symbol udává,
že daný produkt musí být likvidován odděleně od běžného
komunálního odpadu. Odpovídáte za likvidaci tohoto produktu
a dalších elektrických a elektronických zařízení prostřednictvím
určených sběrných míst stanovených vládou nebo místními
úřady. Správná likvidace a recyklace pomáhá předcházet
potenciálním negativním dopadům na životní prostředí a lidské
zdraví. Podrobnější informace o likvidaci starého vybavení si
laskavě vyžádejte od místních úřadů, podniku zabývajícího se
likvidací komunálních odpadů nebo obchodu, kde jste produkt
zakoupili.
Dansk (Danish) - Miljøinformation for kunder i EU
English - Environmental Information for Customers in
the European Union
European Directive 2002/96/EC requires that the equipment
bearing this symbol on the product and/or its packaging must
not be disposed of with unsorted municipal waste. The symbol
indicates that this product should be disposed of separately
from regular household waste streams. It is your responsibility to
dispose of this and other electric and electronic equipment via
designated collection facilities appointed by the government or
local authorities. Correct disposal and recycling will help prevent
potential negative consequences to the environment and
human health. For more detailed information about the disposal
of your old equipment, please contact your local authorities,
waste disposal service, or the shop where you purchased the
product.
Български (Bulgarian) - Информация относно
опазването на околната среда за потребители в
Европейския съюз
Европейска директива 2002/96/EC изисква уредите, носещи
този символ върху изделието и/или опаковката му, да не
се изхвърля т с несортирани битови отпадъци. Символът
обозначава, че изделието трябва да се изхвърля отделно от
сметосъбирането на обикновените битови отпадъци. Ваша
е отговорността този и другите електрически и електронни
уреди да се изхвърлят в предварително определени от
държавните или общински органи специализирани пунктове
за събиране. Правилното изхвърляне и рециклиране
ще спомогнат да се предотвратят евентуални вредни за
околната среда и здравето на населението последствия. За
по-подробна информация относно изхвърлянето на вашите
стари уреди се обърнете към местните власти, службите за
сметосъбиране или магазина, от който сте закупили уреда.
Network Storage System with 2 Bays
EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol
på produktet og/eller emballagen ikke må bortskaffes som
usorteret kommunalt affald. Symbolet betyder, at dette produkt
skal bortskaffes adskilt fra det almindelige husholdningsaffald.
Det er dit ansvar at bortskaffe dette og andet elektrisk og
elektronisk udstyr via bestemte indsamlingssteder udpeget
af staten eller de lokale myndigheder. Korrekt bortskaffelse
og genvinding vil hjælpe med til at undgå mulige skader for
miljøet og menneskers sundhed. Kontakt venligst de lokale
myndigheder, renovationstjenesten eller den butik, hvor du
har købt produktet, angående mere detaljeret information om
bortskaffelse af dit gamle udstyr.
Deutsch (German) - Umweltinformation für Kunden
innerhalb der Europäischen Union
Die Europäische Richtlinie 2002/96/EC verlangt, dass technische
Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit
diesem Symbol versehen ist , nicht zusammen mit unsortiertem
Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf
hin, dass das Produkt von regulärem Haushaltmüll getrennt
entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses
Gerät und andere elektrische und elektronische Geräte über
die dafür zuständigen und von der Regierung oder örtlichen
Behörden dazu bestimmten Sammelstellen zu entsorgen.
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,
potentielle negative Folgen für Umwelt und die menschliche
Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur
Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an
die örtlichen Behörden oder städtischen Entsorgungsdienste
oder an den Händler, bei dem Sie das Produkt erworben haben.
37
Appendix D
Regulatory Information
Eesti (Estonian) - Keskkonnaalane informatsioon
Euroopa Liidus asuvatele klientidele
Français (French) - Informations environnementales
pour les clients de l’Union européenne
Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on
seadmeid, millel on tootel või pakendil käesolev sümbol ,
keelatud kõrvaldada koos sorteerimata olmejäätmetega. See
sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest
olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva
ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike
ametiasutuste poolt ette nähtud kogumispunktide kaudu.
Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida
võimalikke negatiivseid tagajärgi keskkonnale ning inimeste
tervisele. Vanade seadmete kõrvaldamise kohta täpsema
informatsiooni saamiseks võtke palun ühendust kohalike
ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te
toote ostsite.
La directive européenne 2002/96/CE exige que l’équipement
sur lequel est apposé ce symbole sur le produit et/ou son
emballage ne soit pas jeté avec les autres ordures ménagères. Ce
symbole indique que le produit doit être éliminé dans un circuit
distinct de celui pour les déchets des ménages. Il est de votre
responsabilité de jeter ce matériel ainsi que tout autre matériel
électrique ou électronique par les moyens de collecte indiqués
par le gouvernement et les pouvoirs publics des collectivités
territoriales. L’élimination et le recyclage en bonne et due forme
ont pour but de lutter contre l’impact néfaste potentiel de ce
type de produits sur l’environnement et la santé publique. Pour
plus d’informations sur le mode d’élimination de votre ancien
équipement, veuillez prendre contact avec les pouvoirs publics
locaux, le service de traitement des déchets, ou l’endroit où vous
avez acheté le produit.
Español (Spanish) - Información medioambiental para
clientes de la Unión Europea
La Directiva 2002/96/CE de la UE exige que los equipos que
lleven este símbolo en el propio aparato y/o en su embalaje
no deben eliminarse junto con otros residuos urbanos no
seleccionados. El símbolo indica que el producto en cuestión
debe separarse de los residuos domésticos convencionales con
vistas a su eliminación. Es responsabilidad suya desechar este y
cualesquiera otros aparatos eléctricos y electrónicos a través de
los puntos de recogida que ponen a su disposición el gobierno y
las autoridades locales. Al desechar y reciclar correctamente estos
aparatos estará contribuyendo a evitar posibles consecuencias
negativas para el medio ambiente y la salud de las personas. Si
desea obtener información más detallada sobre la eliminación
segura de su aparato usado, consulte a las autoridades locales,
al servicio de recogida y eliminación de residuos de su zona o
pregunte en la tienda donde adquirió el producto.
Ελληνικά (Greek) - Στοιχεία περιβαλλοντικής
προστασίας για πελάτες εντός της Ευρωπαϊκής
Ένωσης
Σύμφωνα με την Κοινοτική Οδηγία 2002/96/EC, ο εξοπλισμός που
φέρει αυτό το σύμβολο στο προϊόν ή/και τη συσκευασία του
δεν πρέπει να απορρίπτεται μαζί με τα μη διαχωρισμένα αστικά
απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα
πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά
απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος
και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των
καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων,
οι οποίες ορίζονται από το κράτος ή τις αρμόδιες τοπικές αρχές.
Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη
ενδεχόμενων αρνητικών επιπτώσεων στο περιβάλλον και την
υγεία. Για περισσότερες πληροφορίες σχετικά με την απόρριψη
του παλαιού σας εξοπλισμού, επικοινωνήστε με τις τοπικές αρχές,
τις υπηρεσίες αποκομιδής απορριμμάτων ή το κατάστημα από
το οποίο αγοράσατε το προϊόν.
Network Storage System with 2 Bays
Italiano (Italian) - Informazioni relative all’ambiente
per i clienti residenti nell’Unione Europea
La direttiva europea 2002/96/EC richiede che le apparecchiature
contrassegnate con questo simbolo
sul prodotto e/o
sull’imballaggio non siano smaltite insieme ai rifiuti urbani
non differenziati. Il simbolo indica che questo prodotto non
deve essere smaltito insieme ai normali rifiuti domestici. È
responsabilità del proprietario smaltire sia questi prodotti sia
le altre apparecchiature elettriche ed elettroniche mediante
le specifiche strutture di raccolta indicate dal governo o dagli
enti pubblici locali. Il corretto smaltimento ed il riciclaggio
aiuteranno a prevenire conseguenze potenzialmente negative
per l’ambiente e per la salute dell’essere umano. Per ricevere
informazioni più dettagliate circa lo smaltimento delle vecchie
apparecchiature in Vostro possesso, Vi invitiamo a contattare gli
enti pubblici di competenza, il servizio di smaltimento rifiuti o il
negozio nel quale avete acquistato il prodotto.
Latviešu valoda (Latvian) - Ekoloģiska informācija
klientiem Eiropas Savienības jurisdikcijā
Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota
zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst
izmest nešķirotā veidā kopā ar komunālajiem atkritumiem
(tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē
to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar
parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo
un citas elektriskas un elektroniskas ierīces izmest atkritumos,
izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko
nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos
un pārstrāde tiek veikta pareizi, tad mazinās iespējamais
kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par
novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt
vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā,
kur iegādājāties šo izstrādājumu.
38
Appendix D
Regulatory Information
Lietuvškai (Lithuanian) - Aplinkosaugos informacija,
skirta Europos Sąjungos vartotojams
Nederlands (Dutch) - Milieu-informatie voor klanten
in de Europese Unie
Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir
kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį),
negalima šalinti kartu su nerūšiuotomis komunalinėmis
atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai
nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad
ši ir kita elektros ar elektroninė įranga būtų šalinama per tam
tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo
sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta
galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos
apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios
institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose
įsigijote tą gaminį.
De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die
is voorzien van dit symbool op het product of de verpakking,
niet mag worden ingezameld met niet-gescheiden huishoudelijk
afval. Dit symbool geeft aan dat het product apart moet worden
ingezameld. U bent zelf verantwoordelijk voor de vernietiging
van deze en andere elektrische en elektronische apparatuur via de
daarvoor door de landelijke of plaatselijke overheid aangewezen
inzamelingskanalen. De juiste vernietiging en recycling van
deze apparatuur voorkomt mogelijke negatieve gevolgen voor
het milieu en de gezondheid. Voor meer informatie over het
vernietigen van uw oude apparatuur neemt u contact op met
de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de
winkel waar u het product hebt aangeschaft.
Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti
fl-Unjoni Ewropea
Norsk (Norwegian) - Miljøinformasjon for kunder i EU
Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih issimbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema
ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika
li dan il-prodott għandu jintrema separatament minn ma’ liskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi
dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku
permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew
mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin
jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u
għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata
dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja
lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew
il-ħanut minn fejn xtrajt il-prodott.
EU-direktiv 2002/96/EF krever at utstyr med følgende symbol
avbildet på produktet og/eller pakningen, ikke må kastes
sammen med usortert avfall. Symbolet indikerer at dette
produktet skal håndteres atskilt fra ordinær avfallsinnsamling
for husholdningsavfall. Det er ditt ansvar å kvitte deg med
dette produktet og annet elektrisk og elektronisk avfall via egne
innsamlingsordninger slik myndighetene eller kommunene
bestemmer. Korrekt avfallshåndtering og gjenvinning vil
være med på å forhindre mulige negative konsekvenser for
miljø og helse. For nærmere informasjon om håndtering av
det kasserte utstyret ditt, kan du ta kontakt med kommunen,
en innsamlingsstasjon for avfall eller butikken der du kjøpte
produktet.
Magyar (Hungarian) - Környezetvédelmi információ az
európai uniós vásárlók számára
Polski (Polish) - Informacja dla klientów w Unii
Europejskiej o przepisach dotyczących ochrony
środowiska
A 2002/96/EC számú európai uniós irányelv megkívánja, hogy
azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán
az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági
hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott
termék kidobásakor a szokványos háztartási hulladékelszállítási
rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön
felelõssége, hogy ezt, és más elektromos és elektronikus
berendezéseit a kormányzati vagy a helyi hatóságok által
kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ
hulladékfeldolgozás segít a környezetre és az emberi egészségre
potenciálisan ártalmas negatív hatások megelõzésében. Ha
elavult berendezéseinek felszámolásához további részletes
információra van szüksége, kérjük, lépjen kapcsolatba a helyi
hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal
üzlettel, ahol a terméket vásárolta.
Network Storage System with 2 Bays
Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt
oznaczony symbolem znajdującym się na produkcie i/lub jego
opakowaniu nie był wyrzucany razem z innymi niesortowanymi
odpadami komunalnymi. Symbol ten wskazuje, że produkt
nie powinien być usuwany razem ze zwykłymi odpadami z
gospodarstw domowych. Na Państwu spoczywa obowiązek
wyrzucania tego i innych urządzeń elektrycznych oraz
elektronicznych w punktach odbioru wyznaczonych przez władze
krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób
i jego recykling pomogą zapobiec potencjalnie negatywnym
konsekwencjom dla środowiska i zdrowia ludzkiego. W celu
uzyskania szczegółowych informacji o usuwaniu starego sprzętu,
prosimy zwrócić się do lokalnych władz, służb oczyszczania
miasta lub sklepu, w którym produkt został nabyty.
39
Appendix D
Regulatory Information
Português (Portuguese) - Informação ambiental para
clientes da União Europeia
Slovenščina (Slovene) - Okoljske informacije za stranke
v Evropski uniji
A Directiva Europeia 2002/96/CE exige que o equipamento
que exibe este símbolo no produto e/ou na sua embalagem
não seja eliminado junto com os resíduos municipais não
separados. O símbolo indica que este produto deve ser
eliminado separadamente dos resíduos domésticos regulares.
É da sua responsabilidade eliminar este e qualquer outro
equipamento eléctrico e electrónico através das instalações
de recolha designadas pelas autoridades governamentais ou
locais. A eliminação e reciclagem correctas ajudarão a prevenir
as consequências negativas para o ambiente e para a saúde
humana. Para obter informações mais detalhadas sobre a
forma de eliminar o seu equipamento antigo, contacte as
autoridades locais, os serviços de eliminação de resíduos ou o
estabelecimento comercial onde adquiriu o produto.
Evropska direktiva 2002/96/ES prepoveduje odlaganje opreme s
tem simbolom – na izdelku in/ali na embalaži z nesortiranimi
komunalnimi odpadki. Ta simbol opozarja, da je treba izdelek
zavreči ločeno od preostalih gospodinjskih odpadkov. Vaša
odgovornost je, da to in preostalo električno in elektronsko
opremo oddate na posebna zbirališča, ki jih določijo državne
ustanove ali lokalne oblasti. S pravilnim odlaganjem in
recikliranjem boste preprečili morebitne škodljive vplive na
okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare
opreme, se obrnite na lokalne oblasti, odlagališče odpadkov ali
trgovino, kjer ste izdelek kupili.
Română (Romanian) - Informaţii de mediu pentru
clienţii din Uniunea Europeană
Directiva europeană 2002/96/CE impune ca echipamentele care
prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să
nu fie casate împreună cu gunoiul menajer municipal. Simbolul
indică faptul că acest produs trebuie să fie casat separat de
gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi
acest produs şi alte echipamente electrice şi electronice prin
intermediul unităţilor de colectare special desemnate de guvern
sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta
la prevenirea potenţialelor consecinţe negative asupra sănătăţii
mediului şi a oamenilor. Pentru mai multe informaţii detaliate
cu privire la casarea acestui echipament vechi, contactaţi
autorităţile locale, serviciul de salubrizare sau magazinul de la
care aţi achiziţionat produsul.
Slovenčina (Slovak) - Informácie o ochrane životného
prostredia pre zákazníkov v Európskej únii
Podľa európskej smernice 2002/96/ES zariadenie s týmto
symbolom
na produkte a/alebo jeho balení nesmie byť
likvidované spolu s netriedeným komunálnym odpadom.
Symbol znamená, že produkt by sa mal likvidovať oddelene
od bežného odpadu z domácností. Je vašou povinnosťou
likvidovať toto i ostatné elektrické a elektronické zariadenia
prostredníctvom špecializovaných zberných zariadení určených
vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia
pomôže zabrániť prípadným negatívnym dopadom na životné
prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie
informácie o likvidácii starého zariadenia, obráťte sa, prosím, na
miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov
alebo obchod, v ktorom ste si produkt zakúpili.
Network Storage System with 2 Bays
Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille
EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä
symboli
itse tuotteessa ja/tai sen pakkauksessa, laitteistoa
ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana.
Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään
tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää
tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet
viemällä tuote tai tuotteet viranomaisten määräämään
keräyspisteeseen. Laitteiston oikea hävittäminen estää
mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten
terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta
saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä
myymälästä, josta ostit tuotteen.
Svenska (Swedish) - Miljöinformation för kunder i
Europeiska unionen
Det europeiska direktivet 2002/96/EC kräver att utrustning med
denna symbol på produkten och/eller förpackningen inte får
kastas med osorterat kommunalt avfall. Symbolen visar att denna
produkt bör kastas efter att den avskiljts från vanligt hushållsavfall.
Det faller på ditt ansvar att kasta denna och annan elektrisk och
elektronisk utrustning på fastställda insamlingsplatser utsedda
av regeringen eller lokala myndigheter. Korrekt kassering och
återvinning skyddar mot eventuella negativa konsekvenser
för miljön och personhälsa. För mer detaljerad information om
kassering av din gamla utrustning kontaktar du dina lokala
myndigheter, avfallshanteringen eller butiken där du köpte
produkten.
WEB: For additional information, please visit
www.linksys.com
40
Appendix E
Appendix E: Software
License Agreement
Software in Linksys Products
This product from Cisco-Linksys LLC or from one of its
affiliates Cisco Systems-Linksys (Asia) Pte Ltd. or CiscoLinksys K.K. (“Linksys”) contains software (including
firmware) originating from Linksys and its suppliers
and may also contain software from the open source
community. Any software originating from Linksys and its
suppliers is licensed under the Linksys Software License
Agreement contained at Schedule 1 below. You may also
be prompted to review and accept that Linksys Software
License Agreement upon installation of the software
Any software from the open source community is licensed
under the specific license terms applicable to that software
made available by Linksys at www.linksys.com/gpl or as
provided for in Schedules 2, 3 and 4 below.
Where such specific license terms entitle you to the source
code of such software, that source code is upon request
available at cost from Linksys for at least three years
from the purchase date of this product and may also be
available for download from www.linksys.com/gpl. For
detailed license terms and additional information on
open source software in Linksys products please look at
the Linksys public web site at: www.linksys.com/gpl/ or
Schedules 2, 3 or 4 below as applicable.
BY DOWNLOADING OR INSTALLING THE SOFTWARE,
OR USING THE PRODUCT CONTAINING THE SOFTWARE,
YOU ARE CONSENTING TO BE BOUND BY THE SOFTWARE
LICENSE AGREEMENTS BELOW. IF YOU DO NOT AGREE TO
ALL OF THESE TERMS, THEN YOU MAY NOT DOWNLOAD,
INSTALL OR USE THE SOFTWARE. YOU MAY RETURN
UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED
AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT)
FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINAL
PURCHASE, SUBJECT TO THE RETURN PROCESS AND
POLICIES OF THE PARTY FROM WHICH YOU PURCHASED
SUCH PRODUCT OR SOFTWARE.
Software Licenses
The software Licenses applicable to software from Linksys
are made available at the Linksys public web site at:
www.linksys.com. For your convenience of reference, a
copy of the Linksys Software License Agreement and the
main open source code licenses used by Linksys in its
products are contained in the Schedules below.
Network Storage System with 2 Bays
Software License Agreement
Schedule 1 - Linksys Software License Agreement
THIS LICENSE AGREEMENT IS BETWEEN YOU AND
CISCO-LINKSYS LLC OR ONE OF ITS AFFILIATES CISCO
SYSTEMS-LINKSYS (ASIA) PTE LTD. OR CISCO-LINKSYS
K.K. (“LINKSYS”) LICENSING THE SOFTWARE INSTEAD OF
CISCO-LINKSYS LLC. BY DOWNLOADING OR INSTALLING
THE SOFTWARE, OR USING THE PRODUCT CONTAINING
THE SOFTWARE, YOU ARE CONSENTING TO BE BOUND BY
THIS AGREEMENT. IF YOU DO NOT AGREE TO ALL OF THESE
TERMS, THEN YOU MAY NOT DOWNLOAD, INSTALL OR USE
THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE
(OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER
PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND
UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO
THE RETURN PROCESS AND POLICIES OF THE PARTY FROM
WHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE.
License. Subject to the terms and conditions of this
Agreement, Linksys grants the original end user purchaser
of the Linksys product containing the Software (“You”)
a nonexclusive license to use the Software solely as
embedded in or (where authorized in the applicable
documentation) for communication with such product.
This license may not be sublicensed, and is not transferable
except to a person or entity to which you transfer
ownership of the complete Linksys product containing
the Software, provided you permanently transfer all rights
under this Agreement and do not retain any full or partial
copies of the Software, and the recipient agrees to the
terms of this Agreement.
“Software” includes, and this Agreement will apply to
(a) the software of Linksys or its suppliers provided in or
with the applicable Linksys product, excluding technology
from the open source community, and (b) any upgrades,
updates, bug fixes or modified versions (“Upgrades”) or
backup copies of the Software supplied to You by Linksys
or an authorized reseller, provided you already hold a
valid license to the original software and have paid any
applicable fee for the Upgrade.
Protection of Information. The Software and
documentation contain trade secrets and/or copyrighted
materials of Linksys or its suppliers. You will not copy
or modify the Software or decompile, decrypt, reverse
engineer or disassemble the Software (except to the
extent expressly permitted by law notwithstanding this
provision), and You will not disclose or make available
such trade secrets or copyrighted material in any form
to any third party. Title to and ownership of the Software
and documentation and any portion thereof, will remain
solely with Linksys or its suppliers.
Collection and Processing of Information. You agree that
Linksys and/or its affiliates may, from time to time, collect
and process information about your Linksys product and/
or the Software and/or your use of either in order (i) to
enable Linksys to offer you Upgrades; (ii) to ensure that
41
Software License Agreement
Appendix E
your Linksys product and/or the Software is being used in
accordance with the terms of this Agreement; (iii) to provide
improvements to the way Linksys delivers technology to
you and to other Linksys customers; (iv) to enable Linksys
to comply with the terms of any agreements it has with
any third parties regarding your Linksys product and/or
Software and/or (v) to enable Linksys to comply with all
applicable laws and/or regulations, or the requirements
of any regulatory authority or government agency.
Linksys and/ or its affiliates may collect and process
this information provided that it does not identify you
personally. Your use of your Linksys product and/or the
Software constitutes this consent by you to Linksys and/
or its affiliates’ collection and use of such information and,
for EEA customers, to the transfer of such information to a
location outside the EEA.
Software Upgrades etc. If the Software enables you to
receive Upgrades, you may elect at any time to receive
these Upgrades either automatically or manually. If you
elect to receive Upgrades manually or you otherwise
elect not to receive or be notified of any Upgrades, you
may expose your Linksys product and/or the Software
to serious security threats and/or some features within
your Linksys product and/or Software may become
inaccessible. There may be circumstances where we
apply an Upgrade automatically in order to comply with
changes in legislation, legal or regulatory requirements
or as a result of requirements to comply with the terms
of any agreements Linksys has with any third parties
regarding your Linksys product and/or the Software. You
will always be notified of any Upgrades being delivered
to you. The terms of this license will apply to any such
Upgrade unless the Upgrade in question is accompanied
by a separate license, in which event the terms of that
license will apply.
Open Source Software. The GPL or other open source
code incorporated into the Software and the open source
license for such source code are available for free download
at http://www.linksys.com/gpl. If You would like a copy
of the GPL or other open source code in this Software on a
CD, Linksys will mail to You a CD with such code for $9.99
plus the cost of shipping, upon request.
Term and Termination. You may terminate this License
at any time by destroying all copies of the Software
and documentation. Your rights under this License will
terminate immediately without notice from Linksys if You
fail to comply with any provision of this Agreement.
Limited Warranty. The warranty terms and period
specified in the applicable Linksys Product User Guide
shall also apply to the Software.
Disclaimer of Liabilities. IN NO EVENT WILL LINKSYS OR
ITS SUPPLIERS BE LIABLE FOR ANY LOST DATA, REVENUE
OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,
INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF
CAUSE (INCLUDING NEGLIGENCE), ARISING OUT OF
Network Storage System with 2 Bays
OR RELATED TO THE USE OF OR INABILITY TO USE THE
SOFTWARE, EVEN IF LINKSYS HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL
LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU
FOR THE PRODUCT. The foregoing limitations will apply
even if any warranty or remedy under this Agreement fails
of its essential purpose. Some jurisdictions do not allow
the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not
apply to You.
Export. Software, including technical data, may be subject
to U.S. export control laws and regulations and/or export
or import regulations in other countries. You agree to
comply strictly with all such laws and regulations.
U.S. Government Users. The Software and documentation
qualify as “commercial items” as defined at 48 C.F.R. 2.101
and 48 C.F.R. 12.212. All Government users acquire the
Software and documentation with only those rights
herein that apply to non-governmental customers.
General Terms. This Agreement will be governed by and
construed in accordance with the laws of the State of
California, without reference to conflict of laws principles.
The United Nations Convention on Contracts for the
International Sale of Goods will not apply. If any portion
of this Agreement is found to be void or unenforceable,
the remaining provisions will remain in full force and
effect. This Agreement constitutes the entire agreement
between the parties with respect to the Software and
supersedes any conflicting or additional terms contained
in any purchase order or elsewhere.
END OF SCHEDULE 1
Schedule 2
If this Linksys product contains open source software
licensed under Version 2 of the “GNU General Public
License” then the license terms below in this Schedule 2
will apply to that open source software. The license terms
below in this Schedule 2 are from the public web site at
http://www.gnu.org/copyleft/gpl.html
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright © 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,
USA
Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not
allowed.
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the
42
Appendix E
GNU General Public License is intended to guarantee your
freedom to share and change free software–to make sure
the software is free for all its users. This General Public
License applies to most of the Free Software Foundation’s
software and to any other program whose authors
commit to using it. (Some other Free Software Foundation
software is covered by the GNU Lesser General Public
License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to
freedom, not price. Our General Public Licenses are
designed to make sure that you have the freedom to
distribute copies of free software (and charge for this
service if you wish), that you receive source code or can
get it if you want it, that you can change the software or
use pieces of it in new free programs; and that you know
you can do these things.
To protect your rights, we need to make restrictions that
forbid anyone to deny you these rights or to ask you to
surrender the rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the
software, or if you modify it.
For example, if you distribute copies of such a program,
whether gratis or for a fee, you must give the recipients
all the rights that you have. You must make sure that they,
too, receive or can get the source code. And you must
show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the
software, and (2) offer you this license which gives you
legal permission to copy, distribute and/or modify the
software.
Also, for each author’s protection and ours, we want to
make certain that everyone understands that there is no
warranty for this free software. If the software is modified
by someone else and passed on, we want its recipients
to know that what they have is not the original, so that
any problems introduced by others will not reflect on the
original authors’ reputations.
Finally, any free program is threatened constantly by
software patents. We wish to avoid the danger that
redistributors of a free program will individually obtain
patent licenses, in effect making the program proprietary.
To prevent this, we have made it clear that any patent must
be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution
and modification follow.
Network Storage System with 2 Bays
Software License Agreement
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License applies to any program or other work
which contains a notice placed by the copyright
holder saying it may be distributed under the terms
of this General Public License. The “Program”, below,
refers to any such program or work, and a “work
based on the Program” means either the Program
or any derivative work under copyright law: that is
to say, a work containing the Program or a portion
of it, either verbatim or with modifications and/
or translated into another language. (Hereinafter,
translation is included without limitation in the term
“modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and
modification are not covered by this License; they
are outside its scope. The act of running the Program
is not restricted, and the output from the Program is
covered only if its contents constitute a work based on
the Program (independent of having been made by
running the Program). Whether that is true depends
on what the Program does.
1. You may copy and distribute verbatim copies of the
Program’s source code as you receive it, in any medium,
provided that you conspicuously and appropriately
publish on each copy an appropriate copyright
notice and disclaimer of warranty; keep intact all the
notices that refer to this License and to the absence
of any warranty; and give any other recipients of the
Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring
a copy, and you may at your option offer warranty
protection in exchange for a fee.
2. You may modify your copy or copies of the Program
or any portion of it, thus forming a work based on the
Program, and copy and distribute such modifications
or work under the terms of Section 1 above, provided
that you also meet all of these conditions:
a. You must cause the modified files to carry
prominent notices stating that you changed the
files and the date of any change.
b. You must cause any work that you distribute or
publish, that in whole or in part contains or is
derived from the Program or any part thereof, to be
licensed as a whole at no charge to all third parties
under the terms of this License.
43
Appendix E
c. If the modified program normally reads commands
interactively when run, you must cause it, when
started running for such interactive use in the most
ordinary way, to print or display an announcement
including an appropriate copyright notice and
a notice that there is no warranty (or else, saying
that you provide a warranty) and that users may
redistribute the program under these conditions,
and telling the user how to view a copy of
this License. (Exception: if the Program itself is
interactive but does not normally print such an
announcement, your work based on the Program
is not required to print an announcement.)
These requirements apply to the modified work as
a whole. If identifiable sections of that work are not
derived from the Program, and can be reasonably
considered independent and separate works in
themselves, then this License, and its terms, do not
apply to those sections when you distribute them as
separate works. But when you distribute the same
sections as part of a whole which is a work based on
the Program, the distribution of the whole must be on
the terms of this License, whose permissions for other
licensees extend to the entire whole, and thus to each
and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights
or contest your rights to work written entirely by you;
rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on
the Program.
In addition, mere aggregation of another work not
based on the Program with the Program (or with a
work based on the Program) on a volume of a storage
or distribution medium does not bring the other work
under the scope of this License.
3. You may copy and distribute the Program (or a
work based on it, under Section 2) in object code or
executable form under the terms of Sections 1 and 2
above provided that you also do one of the following:
a. Accompany it with the complete corresponding
machine-readable source code, which must be
distributed under the terms of Sections 1 and 2
above on a medium customarily used for software
interchange; or,
b. Accompany it with a written offer, valid for at least
three years, to give any third party, for a charge
no more than your cost of physically performing
source distribution, a complete machine-readable
copy of the corresponding source code, to be
distributed under the terms of Sections 1 and 2
above on a medium customarily used for software
interchange; or,
Network Storage System with 2 Bays
Software License Agreement
c. Accompany it with the information you received as
to the offer to distribute corresponding source code.
(This alternative is allowed only for noncommercial
distribution and only if you received the program
in object code or executable form with such an
offer, in accord with Subsection b above.)
The source code for a work means the preferred form
of the work for making modifications to it. For an
executable work, complete source code means all
the source code for all modules it contains, plus any
associated interface definition files, plus the scripts
used to control compilation and installation of the
executable. However, as a special exception, the source
code distributed need not include anything that is
normally distributed (in either source or binary form)
with the major components (compiler, kernel, and so
on) of the operating system on which the executable
runs, unless that component itself accompanies the
executable.
If distribution of executable or object code is made
by offering access to copy from a designated place,
then offering equivalent access to copy the source
code from the same place counts as distribution of
the source code, even though third parties are not
compelled to copy the source along with the object
code.
4. You may not copy, modify, sublicense, or distribute
the Program except as expressly provided under
this License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will
automatically terminate your rights under this License.
However, parties who have received copies, or rights,
from you under this License will not have their licenses
terminated so long as such parties remain in full
compliance.
5. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Program or its
derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying
or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License
to do so, and all its terms and conditions for copying,
distributing or modifying the Program or works based
on it.
6. Each time you redistribute the Program (or any work
based on the Program), the recipient automatically
receives a license from the original licensor to copy,
distribute or modify the Program subject to these
terms and conditions. You may not impose any further
restrictions on the recipients’ exercise of the rights
granted herein. You are not responsible for enforcing
compliance by third parties to this License.
44
Software License Agreement
Appendix E
7. If, as a consequence of a court judgment or allegation
of patent infringement or for any other reason (not
limited to patent issues), conditions are imposed on
you (whether by court order, agreement or otherwise)
that contradict the conditions of this License, they do
not excuse you from the conditions of this License. If
you cannot distribute so as to satisfy simultaneously
your obligations under this License and any other
pertinent obligations, then as a consequence you
may not distribute the Program at all. For example,
if a patent license would not permit royalty-free
redistribution of the Program by all those who receive
copies directly or indirectly through you, then the only
way you could satisfy both it and this License would be
to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or
unenforceable under any particular circumstance,
the balance of the section is intended to apply and
the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or
to contest validity of any such claims; this section has
the sole purpose of protecting the integrity of the free
software distribution system, which is implemented
by public license practices. Many people have
made generous contributions to the wide range of
software distributed through that system in reliance
on consistent application of that system; it is up to
the author/donor to decide if he or she is willing to
distribute software through any other system and a
licensee cannot impose that choice.
This section is intended to make thoroughly clear
what is believed to be a consequence of the rest of this
License.
8. If the distribution and/or use of the Program is
restricted in certain countries either by patents or by
copyrighted interfaces, the original copyright holder
who places the Program under this License may add an
explicit geographical distribution limitation excluding
those countries, so that distribution is permitted only
in or among countries not thus excluded. In such case,
this License incorporates the limitation as if written in
the body of this License.
9. The Free Software Foundation may publish revised
and/or new versions of the General Public License
from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to
address new problems or concerns.
Each version is given a distinguishing version number.
If the Program specifies a version number of this
License which applies to it and “any later version”, you
have the option of following the terms and conditions
either of that version or of any later version published
by the Free Software Foundation. If the Program does
Network Storage System with 2 Bays
not specify a version number of this License, you
may choose any version ever published by the Free
Software Foundation.
10.If you wish to incorporate parts of the Program into
other free programs whose distribution conditions are
different, write to the author to ask for permission. For
software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will
be guided by the two goals of preserving the free status
of all derivatives of our free software and of promoting
the sharing and reuse of software generally.
NO WARRANTY
11.BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU.
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU
ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE,
BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY TO
USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR
A FAILURE OF THE PROGRAM TO OPERATE WITH ANY
OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER
PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
END OF TERMS AND CONDITIONS
END OF SCHEDULE 2
Schedule 3
If this Linksys product contains open source software
licensed under Version 2.1 of the“GNU Lesser General Public
License” then the license terms below in this Schedule 3
will apply to that open source software. The license terms
below in this Schedule 3 are from the public web site at
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html.
45
Appendix E
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,
USA
Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not
allowed.
[This is the first released version of the Lesser GPL. It also
counts as the successor of the GNU Library Public License,
version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the GNU
General Public Licenses are intended to guarantee your
freedom to share and change free software—to make
sure the software is free for all its users.
This license, the Lesser General Public License, applies to
some specially designated software packages—typically
libraries—of the Free Software Foundation and other
authors who decide to use it. You can use it too, but we
suggest you first think carefully about whether this license
or the ordinary General Public License is the better strategy
to use in any particular case, based on the explanations
below.
When we speak of free software, we are referring to
freedom of use, not price. Our General Public Licenses
are designed to make sure that you have the freedom
to distribute copies of free software (and charge for this
service if you wish); that you receive source code or can
get it if you want it; that you can change the software and
use pieces of it in new free programs; and that you are
informed that you can do these things.
To protect your rights, we need to make restrictions that
forbid distributors to deny you these rights or to ask you
to surrender these rights. These restrictions translate to
certain responsibilities for you if you distribute copies of
the library or if you modify it.
For example, if you distribute copies of the library,
whether gratis or for a fee, you must give the recipients
all the rights that we gave you. You must make sure that
they, too, receive or can get the source code. If you link
other code with the library, you must provide complete
object files to the recipients, so that they can relink them
with the library after making changes to the library and
recompiling it. And you must show them these terms so
they know their rights.
We protect your rights with a two-step method: (1) we
copyright the library, and (2) we offer you this license,
which gives you legal permission to copy, distribute and/
or modify the library.
Network Storage System with 2 Bays
Software License Agreement
To protect each distributor, we want to make it very clear
that there is no warranty for the free library. Also, if the
library is modified by someone else and passed on, the
recipients should know that what they have is not the
original version, so that the original author’s reputation
will not be affected by problems that might be introduced
by others.
Finally, software patents pose a constant threat to the
existence of any free program. We wish to make sure
that a company cannot effectively restrict the users of
a free program by obtaining a restrictive license from a
patent holder. Therefore, we insist that any patent license
obtained for a version of the library must be consistent
with the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered
by the ordinary GNU General Public License. This license,
the GNU Lesser General Public License, applies to certain
designated libraries, and is quite different from the
ordinary General Public License. We use this license for
certain libraries in order to permit linking those libraries
into non-free programs.
When a program is linked with a library, whether
statically or using a shared library, the combination of
the two is legally speaking a combined work, a derivative
of the original library. The ordinary General Public
License therefore permits such linking only if the entire
combination fits its criteria of freedom. The Lesser General
Public License permits more lax criteria for linking other
code with the library.
We call this license the “Lesser” General Public License
because it does Less to protect the user’s freedom than
the ordinary General Public License. It also provides
other free software developers Less of an advantage over
competing non-free programs. These disadvantages are
the reason we use the ordinary General Public License
for many libraries. However, the Lesser license provides
advantages in certain special circumstances.
For example, on rare occasions, there may be a special
need to encourage the widest possible use of a certain
library, so that it becomes a de-facto standard. To achieve
this, non-free programs must be allowed to use the library.
A more frequent case is that a free library does the same
job as widely used non-free libraries. In this case, there is
little to gain by limiting the free library to free software
only, so we use the Lesser General Public License.
In other cases, permission to use a particular library in nonfree programs enables a greater number of people to use
a large body of free software. For example, permission to
use the GNU C Library in non-free programs enables many
more people to use the whole GNU operating system, as
well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less
protective of the users’ freedom, it does ensure that the
user of a program that is linked with the Library has the
46
Appendix E
freedom and the wherewithal to run that program using a
modified version of the Library.
The precise terms and conditions for copying, distribution
and modification follow. Pay close attention to the
difference between a “work based on the library” and a
“work that uses the library”. The former contains code
derived from the library, whereas the latter must be
combined with the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License Agreement applies to any software library
or other program which contains a notice placed by
the copyright holder or other authorized party saying
it may be distributed under the terms of this Lesser
General Public License (also called “this License”). Each
licensee is addressed as “you”.
A “library” means a collection of software functions
and/or data prepared so as to be conveniently linked
with application programs (which use some of those
functions and data) to form executables.
The “Library”, below, refers to any such software library
or work which has been distributed under these terms.
A “work based on the Library” means either the Library
or any derivative work under copyright law: that is to
say, a work containing the Library or a portion of it,
either verbatim or with modifications and/or translated
straightforwardly into another language. (Hereinafter,
translation is included without limitation in the term
“modification”.)
“Source code” for a work means the preferred form of
the work for making modifications to it. For a library,
complete source code means all the source code for
all modules it contains, plus any associated interface
definition files, plus the scripts used to control
compilation and installation of the library.
Activities other than copying, distribution and
modification are not covered by this License; they are
outside its scope. The act of running a program using
the Library is not restricted, and output from such a
program is covered only if its contents constitute a
work based on the Library (independent of the use
of the Library in a tool for writing it). Whether that is
true depends on what the Library does and what the
program that uses the Library does.
Network Storage System with 2 Bays
Software License Agreement
1. You may copy and distribute verbatim copies of the
Library’s complete source code as you receive it, in
any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep
intact all the notices that refer to this License and to
the absence of any warranty; and distribute a copy of
this License along with the Library.
You may charge a fee for the physical act of transferring
a copy, and you may at your option offer warranty
protection in exchange for a fee.
2. You may modify your copy or copies of the Library or
any portion of it, thus forming a work based on the
Library, and copy and distribute such modifications
or work under the terms of Section 1 above, provided
that you also meet all of these conditions:
a) The modified work must itself be a software
library.
b) You must cause the files modified to carry
prominent notices stating that you changed the
files and the date of any change.
c) You must cause the whole of the work to be
licensed at no charge to all third parties under the
terms of this License.
d) If a facility in the modified Library refers to a function
or a table of data to be supplied by an application
program that uses the facility, other than as an
argument passed when the facility is invoked, then
you must make a good faith effort to ensure that,
in the event an application does not supply such
function or table, the facility still operates, and
performs whatever part of its purpose remains
meaningful.
(For example, a function in a library to compute
square roots has a purpose that is entirely welldefined independent of the application. Therefore,
Subsection 2d requires that any applicationsupplied function or table used by this function
must be optional: if the application does not supply
it, the square root function must still compute
square roots.)
These requirements apply to the modified work as
a whole. If identifiable sections of that work are not
derived from the Library, and can be reasonably
considered independent and separate works in
themselves, then this License, and its terms, do
not apply to those sections when you distribute
them as separate works. But when you distribute
the same sections as part of a whole which is a
work based on the Library, the distribution of the
whole must be on the terms of this License, whose
permissions for other licensees extend to the entire
whole, and thus to each and every part regardless
of who wrote it.
47
Appendix E
Thus, it is not the intent of this section to claim
rights or contest your rights to work written entirely
by you; rather, the intent is to exercise the right to
control the distribution of derivative or collective
works based on the Library.
In addition, mere aggregation of another work
not based on the Library with the Library (or with
a work based on the Library) on a volume of a
storage or distribution medium does not bring the
other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU
General Public License instead of this License to a
given copy of the Library. To do this, you must alter all
the notices that refer to this License, so that they refer
to the ordinary GNU General Public License, version
2, instead of to this License. (If a newer version than
version 2 of the ordinary GNU General Public License
has appeared, then you can specify that version
instead if you wish.) Do not make any other change in
these notices.
Once this change is made in a given copy, it is
irreversible for that copy, so the ordinary GNU General
Public License applies to all subsequent copies and
derivative works made from that copy.
This option is useful when you wish to copy part of the
code of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion
or derivative of it, under Section 2) in object code or
executable form under the terms of Sections 1 and
2 above provided that you accompany it with the
complete corresponding machine-readable source
code, which must be distributed under the terms of
Sections 1 and 2 above on a medium customarily used
for software interchange.
If distribution of object code is made by offering
access to copy from a designated place, then offering
equivalent access to copy the source code from the
same place satisfies the requirement to distribute
the source code, even though third parties are not
compelled to copy the source along with the object
code.
5. A program that contains no derivative of any portion
of the Library, but is designed to work with the Library
by being compiled or linked with it, is called a “work
that uses the Library”. Such a work, in isolation, is not
a derivative work of the Library, and therefore falls
outside the scope of this License.
However, linking a “work that uses the Library” with
the Library creates an executable that is a derivative
of the Library (because it contains portions of the
Library), rather than a “work that uses the library”. The
executable is therefore covered by this License. Section
6 states terms for distribution of such executables.
Network Storage System with 2 Bays
Software License Agreement
When a “work that uses the Library” uses material from
a header file that is part of the Library, the object code
for the work may be a derivative work of the Library
even though the source code is not. Whether this is
true is especially significant if the work can be linked
without the Library, or if the work is itself a library. The
threshold for this to be true is not precisely defined by
law.
If such an object file uses only numerical parameters,
data structure layouts and accessors, and small macros
and small inline functions (ten lines or less in length),
then the use of the object file is unrestricted, regardless
of whether it is legally a derivative work. (Executables
containing this object code plus portions of the Library
will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you
may distribute the object code for the work under the
terms of Section 6. Any executables containing that
work also fall under Section 6, whether or not they are
linked directly with the Library itself.
6. As an exception to the Sections above, you may also
combine or link a “work that uses the Library” with the
Library to produce a work containing portions of the
Library, and distribute that work under terms of your
choice, provided that the terms permit modification
of the work for the customer’s own use and reverse
engineering for debugging such modifications.
You must give prominent notice with each copy of
the work that the Library is used in it and that the
Library and its use are covered by this License. You
must supply a copy of this License. If the work during
execution displays copyright notices, you must include
the copyright notice for the Library among them, as
well as a reference directing the user to the copy of this
License. Also, you must do one of these things:
a) Accompany the work with the complete
corresponding machine-readable source code
for the Library including whatever changes were
used in the work (which must be distributed
under Sections 1 and 2 above); and, if the work
is an executable linked with the Library, with the
complete machine-readable “work that uses the
Library”, as object code and/or source code, so that
the user can modify the Library and then relink
to produce a modified executable containing the
modified Library. (It is understood that the user
who changes the contents of definitions files in the
Library will not necessarily be able to recompile the
application to use the modified definitions.)
48
Appendix E
Software License Agreement
b) Use a suitable shared library mechanism for linking
with the Library. A suitable mechanism is one that
(1) uses at run time a copy of the library already
present on the user’s computer system, rather than
copying library functions into the executable, and
(2) will operate properly with a modified version of
the library, if the user installs one, as long as the
modified version is interface-compatible with the
version that the work was made with.
8. You may not copy, modify, sublicense, link with, or
distribute the Library except as expressly provided
under this License. Any attempt otherwise to copy,
modify, sublicense, link with, or distribute the Library
is void, and will automatically terminate your rights
under this License. However, parties who have received
copies, or rights, from you under this License will not
have their licenses terminated so long as such parties
remain in full compliance.
c) Accompany the work with a written offer, valid
for at least three years, to give the same user the
materials specified in Subsection 6a, above, for a
charge no more than the cost of performing this
distribution.
9. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Library or its
derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying
or distributing the Library (or any work based on the
Library), you indicate your acceptance of this License
to do so, and all its terms and conditions for copying,
distributing or modifying the Library or works based
on it.
d) If distribution of the work is made by offering access
to copy from a designated place, offer equivalent
access to copy the above specified materials from
the same place.
e) Verify that the user has already received a copy of
these materials or that you have already sent this
user a copy.
For an executable, the required form of the “work that
uses the Library” must include any data and utility
programs needed for reproducing the executable from
it. However, as a special exception, the materials to be
distributed need not include anything that is normally
distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless
that component itself accompanies the executable.
It may happen that this requirement contradicts the
license restrictions of other proprietary libraries that
do not normally accompany the operating system.
Such a contradiction means you cannot use both
them and the Library together in an executable that
you distribute.
7. You may place library facilities that are a work based
on the Library side-by-side in a single library together
with other library facilities not covered by this License,
and distribute such a combined library, provided that
the separate distribution of the work based on the
Library and of the other library facilities is otherwise
permitted, and provided that you do these two
things:
a) Accompany the combined library with a copy of the
same work based on the Library, uncombined with
any other library facilities. This must be distributed
under the terms of the Sections above.
b) Give prominent notice with the combined library of
the fact that part of it is a work based on the Library,
and explaining where to find the accompanying
uncombined form of the same work.
Network Storage System with 2 Bays
10.Each time you redistribute the Library (or any work
based on the Library), the recipient automatically
receives a license from the original licensor to copy,
distribute, link with or modify the Library subject
to these terms and conditions. You may not impose
any further restrictions on the recipients’ exercise of
the rights granted herein. You are not responsible
for enforcing compliance by third parties with this
License.
11.If, as a consequence of a court judgment or allegation
of patent infringement or for any other reason (not
limited to patent issues), conditions are imposed on
you (whether by court order, agreement or otherwise)
that contradict the conditions of this License, they do
not excuse you from the conditions of this License. If
you cannot distribute so as to satisfy simultaneously
your obligations under this License and any other
pertinent obligations, then as a consequence you may
not distribute the Library at all. For example, if a patent
license would not permit royalty-free redistribution of
the Library by all those who receive copies directly or
indirectly through you, then the only way you could
satisfy both it and this License would be to refrain
entirely from distribution of the Library.
If any portion of this section is held invalid or
unenforceable under any particular circumstance,
the balance of the section is intended to apply, and
the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or
to contest validity of any such claims; this section has
the sole purpose of protecting the integrity of the free
software distribution system which is implemented
by public license practices. Many people have
made generous contributions to the wide range of
49
Software License Agreement
Appendix E
software distributed through that system in reliance
on consistent application of that system; it is up to
the author/donor to decide if he or she is willing to
distribute software through any other system and a
licensee cannot impose that choice.
This section is intended to make thoroughly clear
what is believed to be a consequence of the rest of this
License.
12.If the distribution and/or use of the Library is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places
the Library under this License may add an explicit
geographical distribution limitation excluding those
countries, so that distribution is permitted only in or
among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the
body of this License.
13.The Free Software Foundation may publish revised
and/or new versions of the Lesser General Public
License from time to time. Such new versions will be
similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number.
If the Library specifies a version number of this License
which applies to it and “any later version”, you have the
option of following the terms and conditions either of
that version or of any later version published by the Free
Software Foundation. If the Library does not specify a
license version number, you may choose any version
ever published by the Free Software Foundation.
15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE LIBRARY, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE
LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD
THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE
COST OF ALL NECESSARY SERVICING, REPAIR OR
CORRECTION.
16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW
OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY
AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE
USE OR INABILITY TO USE THE LIBRARY (INCLUDING
BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY
YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY
TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
END OF SCHEDULE 3
14.If you wish to incorporate parts of the Library into
other free programs whose distribution conditions are
incompatible with these, write to the author to ask for
permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for
this. Our decision will be guided by the two goals of
preserving the free status of all derivatives of our free
software and of promoting the sharing and reuse of
software generally.
Schedule 4
NO WARRANTY
This product includes software written by Tim Hudson
(tjh@cryptsoft.com).
If this Linksys product contains open source software
licensed under the OpenSSL license:
This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit.
(http://www.openssl.org/).
This product includes cryptographic software written by
Eric Young (eay@cryptsoft.com).
In addition, if this Linksys product contains open
source software licensed under the OpenSSL license
then the license terms below in this Schedule 3 will
apply to that open source software. The license terms
below in this Schedule 3 are from the public web site at
http://www.openssl.org/source/license.html.
The OpenSSL toolkit stays under a dual license, i.e. both
the conditions of the OpenSSL License and the original
SSLeay license apply to the toolkit. See below for the
actual license texts. Actually both licenses are BSD-style
Open Source licenses. In case of any license issues related
to OpenSSL please contact openssl-core@openssl.org.
Network Storage System with 2 Bays
50
Appendix E
Software License Agreement
OpenSSL License
Original SSLeay License
Copyright © 1998-2007 The OpenSSL Project. All rights
reserved.
Copyright © 1995-1998 Eric Young (eay@cryptsoft.com)All
rights reserved.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
This package is an SSL implementation written by Eric
Young (eay@cryptsoft.com).
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or
other materials provided with the distribution.
3. All advertising materials mentioning features or
use of this software must display the following
acknowledgment: “This product includes software
developed by the OpenSSL Project for use in the
OpenSSL Toolkit. (http://www.openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project”
must not be used to endorse or promote products
derived from this software without prior written
permission. For written permission, please contact
openssl-core@openssl.org.
5. Products derived from this software may not be called
“OpenSSL” nor may “OpenSSL” appear in their names
without prior written permission of the OpenSSL
Project.
6. Redistributions of any form whatsoever must retain
the following acknowledgment: “This product includes
software developed by the OpenSSL Project for use in
the OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT
“AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
This product includes cryptographic software written by
Eric Young (eay@cryptsoft.com). This product includes
software written by Tim Hudson (tjh@cryptsoft.com).
Network Storage System with 2 Bays
The implementation was written so as to conform with
Netscape’s SSL.
This library is free for commercial and non-commercial
use as long as the following conditions are adhered to.
The following conditions apply to all code found in this
distribution, be it the RC4, RSA, lhash, DES, etc., code; not
just the SSL code. The SSL documentation included with
this distribution is covered by the same copyright terms
except that the holder is Tim Hudson (tjh@cryptsoft.
com).
Copyright remains Eric Young’s, and as such any Copyright
notices in the code are not to be removed.
If this package is used in a product, Eric Young should be
given attribution as the author of the parts of the library
used. This can be in the form of a textual message at
program startup or in documentation (online or textual)
provided with the package.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the
copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or
other materials provided with the distribution.
3. All advertising materials mentioning features or
use of this software must display the following
acknowledgement:
“This product includes cryptographic software written
by Eric Young (eay@cryptsoft.com)”
The word ‘cryptographic’ can be left out if the routines
from the library being used are not cryptographic
related.
4. If you include any Windows specific code (or a derivative
thereof ) from the apps directory (application code)
you must include an acknowledgement: “This product
includes software written by Tim Hudson (tjh@
cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY
51
Appendix E
Software License Agreement
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The license and distribution terms for any publicly available
version or derivative of this code cannot be changed. i.e.
this code cannot simply be copied and put under another
distribution license [including the GNU Public License.]
END OF SCHEDULE 4
8101010B-ST
Network Storage System with 2 Bays
52
Download PDF