INSTALLATION
LED RUN/BRAKE REAR FENDER TIP
3225
PARTS INCLUDED
1
1
1
Lighted Rear Fender Trim Assembly
Hardware Kit Containing
1
6 Plug Wire Harness Adapter
4
4” Nylon Cable Ties
1
Dielectric Grease Packet
2
Nylon Cord Keepers
1
Alcohol Pad
Installation Instructions
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING KϋRYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR
PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL
INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES REGARDING
THE USE AND CARE OF THIS PRODUCT.
WARNING!
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING
THE CONTENTS DESCRIBED HEREIN CAN RESULT IN
POTENTIAL DEATH OR SERIOUS INJURY
ATTENTION! This indication alerts you to the fact that ignoring the contents
described herein may negatively affect product performance and
functionality.
CAUTION!
This indication alerts you to the fact that ignoring the contents
described herein can result in potential injury or material
damage.
TOOLS SUGGESTED
Set of Metric Hex wrenches, Set of Metric Combination Wrenches, Masking tape or
Non-Permanent Marker, Cleaning Supplies, Clean Towel
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.
STEP 1
Read and understand all steps in the instructions before starting the
installation. Park the motorcycle on a hard, level surface and turn off the
ignition.
CAUTION!
Avoid potential electrical shock! Disconnect the battery before
starting this procedure.
STEP 2
Remove the four fasteners that secure the rear license plate panel. Some
earlier models may have a fifth fastener behind the license plate. Gently pull off
the back panel exposing the wiring harness. (Red and Blue plugs)
PIC 1 and PIC 2
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products
sold hereunder, shall be free of defects in
materials and workmanship for a period of one
(1) year from the date of purchase by the
consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt
showing the date the customer purchased the
product(s).
●The product must be properly installed,
maintained and operated under
normal conditions.
●Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated
products.
●Küryakyn shall not be liable for any
consequential and incidental damages, including
labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in
delivery, delivery in nonconforming condition, or
for any breech of contract or duty between
Küryakyn and a customer.
●Küryakyn products are often intended for use in
specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
●Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the
consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects
in materials and workmanship for 3 years from
the date of purchase where as all other
components shall be warranted for one(1) year.
This includes, but is not limited to; control
modules, wiring, chrome & other components.
●Küryakyn makes no warranty of any kind in
regard to other manufacturer¹s products
distributed by Küryakyn. Küryakyn will pass on
all warranties made by the manufacturer and
where possible, will expedite the claim on behalf
of the customer, but ultimately, responsibility for
disposition of the warranty claim lies
with the manufacturer.
ABOUT OUR CATALOG
For purchasing Küryakyn® products, you
can receive a complete catalog free of charge.
Send the Proof-of-Purchase below with
your address to: Küryakyn, P.O. Box 339,
Somerset, WI 54025.
Please indicate either Accessories Catalog for
Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights reserved.
-cont.3225-21GL-0111
STEP 3
Locate the stock wiring plugs, (unplug either the blue or red plugs) and insert the
supplied wiring harness in between the stock plugs. PIC 2 One of the two small
connectors shown in PIC 3 is where you will be plugging in the light. If you have
already installed additional lights in the rear, you may already have an extra
connection available to use so you will not need to install the wire harness.
PIC 1
ATTENTION!
Küryakyn recommends the use of dielectric grease on electrical
connections.
REMOVE THESE FASTENERS
ATTENTION!
Thoroughly clean the area of grease, oil, dirt, or other debris to ensure
proper adhesion. Küryakyn WILL NOT warranty any parts lost due to
improper installation.
ATTENTION!
The adhesive may not correctly bond if applied at temperatures less than
50°F. Do not attempt this installation in temperatures less than 50°F.
STEP 4
Test fit the Fender Accent. Mark the fender panel along the top with a piece of
masking tape or non-permanent marker when the bottom edge of the trim is
lined up with the bottom edge of the fender. Make sure when test fitting the trim
that the wire exits from the bottom of the trim and is not pinched between the
trim and the fender.
STEP 5
Remove any grease or debris from the installation area with soapy water and a
clean rag; allow the area to dry completely. Clean the rear fender base with the
included alcohol cleaning pad to remove any residue and allow the area to dry
completely.
STEP 6
PIC 2
PIC 3
Rub the backing on the adhesive strip to activate the adhesive before applying.
Remove the adhesive backing. Press the fender trim into place and hold for 1
minute to ensure proper adhesion. Full bond strength will occur within 24 hours.
ATTENTION!
Secure all wiring away from any moving parts, pinch points or extreme
heat. Küryakyn WILL NOT issue a warranty on any electrical component
that fails due to pinched, crimped, broken, abraded, melted or frayed
wires.
STEP 7
Route the wire harness up the inside of the rear fender panel, keeping it away
from pinch points. Make sure to check placement of cord keepers so they do not
interfere with the frame of the motorcycle when replacing the panel. Clean the
fender panel thoroughly where you need to put the included cord keepers and
attach them to the inside of the fender panel. Lift the tab on the cord keepers
and insert the wire harness. PIC 4
STEP 8
Plug in the harness to the wiring adapter installed in Step 3. Reinstall the rear
fender panel to the bike.
STEP 9
Reconnect the battery and test the lights for correct operation.
PIC 4
ATTENTION!
It is the installer’s responsibility to ensure that all of the fasteners
(including pre-assembled) are tightened before operation of the
motorcycle. Küryakyn will not issue a warranty on components lost due
to improper installation. Periodic maintenance may be required.
PAGE
2
Ride On!
LED RUN/BRAKE FENDER TRIM
INSTALLATION
">
