Cabletron Systems | 6C105 | Installation guide | Cabletron Systems 6C105 Installation guide

Title Page
SWPIM-E1
Installation Guide
LNK
STS
9033059-02
SWPIM-E1
Only qualified personnel should perform installation
procedures.
NOTICE
Cabletron Systems reserves the right to make changes in specifications and other information
contained in this document without prior notice. The reader should in all cases consult Cabletron
Systems to determine whether any such changes have been made.
The hardware, firmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL,
INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT
NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR
THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN
ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH
DAMAGES.
Cabletron Systems, Inc.
35 Industrial Way
Rochester, NH 03867
 1999 by Cabletron Systems, Inc.
All Rights Reserved
Printed in the United States of America
Order Number: 9033059-02 October 1999
Cabletron Systems, SPECTRUM, and LANVIEW are registered trademarks and SmartSwitch is a
trademark of Cabletron Systems, Inc.
All other product names mentioned in this manual may be trademarks or registered trademarks of
their respective companies.
VCCI NOTICE
This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment,
radio disturbance may arise. When such trouble occurs, the user may be required to take corrective
actions.
SWPIM-E1 Installation Guide
i
Notice
CABLETRON SYSTEMS, INC.
PROGRAM LICENSE AGREEMENT
IMPORTANT:
THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE FOLLOWING
GEOGRAPHICAL REGIONS:
CANADA
MEXICO
CENTRAL AMERICA
SOUTH AMERICA
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,
CAREFULLY READ THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron
Systems, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron
software program (“Program”) in the package. The Program may be contained in firmware, chips or
other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME
BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND
THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT
AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED PRODUCT TO
CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE
OF RECEIPT FOR A FULL REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON
SYSTEMS +1-603-332-9400. Attn: Legal Department.
1.
LICENSE. You have the right to use only the one (1) copy of the Program provided in this
package subject to the terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2.
OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
3.
APPLICABLE LAW. This License Agreement shall be interpreted and governed under the
laws and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and
venue of the New Hampshire courts.
4.
EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to
regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which
prohibit export or diversion of certain technical products to certain countries, unless a license to export
the product is obtained from the U.S. Government or an exception from obtaining such license may be
relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under
the U.S. Export Administration Regulations, You agree that You are a civil end user of the Program
and agree that You will use the Program for civil end uses only and not for military purposes.
ii
SWPIM-E1 Installation Guide
Notice
If the Program is exported from the United States pursuant to the License Exception TSR under
the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in
Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the Program, the source
code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania,
Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan,
Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other
countries as may be designated by the United States Government), (ii) export to Country Groups D:1
or E:2 (as defined herein) the direct product of the Program or the technology, if such foreign
produced direct product is subject to national security controls as identified on the U.S. Commerce
Control List, or (iii) if the direct product of the technology is a complete plant o r any major
component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as
identified on the U.S. Commerce Control List or is subject to State Department controls under the
U.S. Munitions List.
5.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i)
was developed solely at private expense; (ii) contains “restricted computer software” submitted with
restricted rights in accordance with section 52.227-19 (a) through (d) of the Commercial Computer
Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data
belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product is considered
commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and
use, duplication, or disclosure by the Government is subject to restrictions set forth herein.
6.
EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its
documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO
YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING
WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL,
CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE
USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED
WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY
NOT APPLY TO YOU.
SWPIM-E1 Installation Guide
iii
Notice
CABLETRON SYSTEMS SALES AND SERVICE, INC.
PROGRAM LICENSE AGREEMENT
IMPORTANT:
THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE UNITED
STATES OF AMERICA AND BY UNITED STATES OF AMERICA
GOVERNMENT END USERS.
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,
CAREFULLY READ THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron Systems
Sales and Service, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the
Cabletron software program (“Program”) in the package. The Program may be contained in firmware,
chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO
BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE
LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF
YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED
PRODUCT TO CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS
FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON
SYSTEMS +1-603-332-9400. Attn: Legal Department.
1.
LICENSE. You have the right to use only the one (1) copy of the Program provided in this
package subject to the terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2.
OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
3.
APPLICABLE LAW. This License Agreement shall be interpreted and governed under the
laws and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and
venue of the New Hampshire courts.
4.
EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to
regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which
prohibit export or diversion of certain technical products to certain countries, unless a license to export
the product is obtained from the U.S. Government or an exception from obtaining such license may be
relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under
the U.S. Export Administration Regulations, You agree that You are a civil end user of the Program
and agree that You will use the Program for civil end uses only and not for military purposes.
iv
SWPIM-E1 Installation Guide
Notice
If the Program is exported from the United States pursuant to the License Exception TSR under
the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in
Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the Program, the source
code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania,
Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan,
Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other
countries as may be designated by the United States Government), (ii) export to Country Groups D:1
or E:2 (as defined herein) the direct product of the Program or the technology, if such foreign
produced direct product is subject to national security controls as identified on the U.S. Commerce
Control List, or (iii) if the direct product of the technology is a complete plant o r any major
component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as
identified on the U.S. Commerce Control List or is subject to State Department controls under the
U.S. Munitions List.
5.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i)
was developed solely at private expense; (ii) contains “restricted computer software” submitted with
restricted rights in accordance with section 52.227-19 (a) through (d) of the Commercial Computer
Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data
belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product is considered
commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and
use, duplication, or disclosure by the Government is subject to restrictions set forth herein.
6.
EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its
documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO
YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING
WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL,
CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE
USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED
WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY
NOT APPLY TO YOU.
SWPIM-E1 Installation Guide
v
Notice
CABLETRON SYSTEMS LIMITED
PROGRAM LICENSE AGREEMENT
IMPORTANT:
THIS LICENSE APPLIES FOR THE USE OF THE PRODUCT IN THE
FOLLOWING GEOGRAPHICAL REGIONS:
EUROPE
MIDDLE EAST
AFRICA
ASIA
AUSTRALIA
PACIFIC RIM
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,
CAREFULLY READ THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron
Systems Limited (“Cabletron”) that sets forth your rights and obligations with respect to the
Cabletron software program (“Program”) in the package. The Program may be contained in firmware,
chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO
BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE
LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF
YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED
PRODUCT TO CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS
FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON
SYSTEMS +1-603-332-9400. Attn: Legal Department.
1.
LICENSE. You have the right to use only the one (1) copy of the Program provided in this
package subject to the terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2.
OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
3.
APPLICABLE LAW. This License Agreement shall be governed in accordance with English
law. The English courts shall have exclusive jurisdiction in the event of any disputes.
4.
EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to
regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which
prohibit export or diversion of certain technical products to certain countries, unless a license to export
the product is obtained from the U.S. Government or an exception from obtaining such license may be
relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under
the U.S. Export Administration Regulations, You agree that You are a civil end user of the Program
and agree that You will use the Program for civil end uses only and not for military purposes.
vi
SWPIM-E1 Installation Guide
Notice
If the Program is exported from the United States pursuant to the License Exception TSR under
the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in
Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the Program, the source
code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania,
Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan,
Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other
countries as may be designated by the United States Government), (ii) export to Country Groups D:1
or E:2 (as defined herein) the direct product of the Program or the technology, if such foreign
produced direct product is subject to national security controls as identified on the U.S. Commerce
Control List, or (iii) if the direct product of the technology is a complete plant o r any major
component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as
identified on the U.S. Commerce Control List or is subject to State Department controls under the
U.S. Munitions List.
5.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i)
was developed solely at private expense; (ii) contains “restricted computer software” submitted with
restricted rights in accordance with section 52.227-19 (a) through (d) of the Commercial Computer
Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data
belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product is considered
commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and
use, duplication, or disclosure by the Government is subject to restrictions set forth herein.
6.
EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its
documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO
YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING
WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL,
CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE
USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED
WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY
NOT APPLY TO YOU.
SWPIM-E1 Installation Guide
vii
Notice
DECLARATION OF CONFORMITY
Application of Council Directive(s):
Manufacturer’s Name:
Manufacturer’s Address:
European Representative Name:
European Representative Address:
Conformance to Directive(s)/Product Standards:
Equipment Type/Environment:
89/336/EEC
73/23/EEC
Cabletron Systems, Inc.
35 Industrial Way
PO Box 5005
Rochester, NH 03867
Mr. J. Solari
Cabletron Systems Limited
Nexus House, Newbury Business Park
London Road, Newbury
Berkshire RG14 2PZ, England
EC Directive 89/336/EEC
EC Directive 73/23/EEC
EN 55022
EN 50082-1
EN 60950
Networking Equipment, for use in a
Commercial or Light Industrial
Environment.
We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged
with this notice conforms to the above directives.
Manufacturer
Legal Representative in Europe
Mr.
Ronald Fotino
___________________________________
Full Name
Mr.
J. Solari
___________________________________
Full Name
Compliance
Engineering Manager
___________________________________
Title
Managing
Director - E.M.E.A.
___________________________________
Title
Rochester,
NH, USA
___________________________________
Location
Newbury,
Berkshire, England
___________________________________
Location
viii
SWPIM-E1 Installation Guide
CONTENTS
INTRODUCTION
Using This Guide ............................................................................xi
Structure of This Guide...................................................................xi
SWPIM-E1 Features...................................................................... xii
Related Manuals........................................................................... xiii
Document Conventions ................................................................ xiv
Getting Help...................................................................................xv
CHAPTER 1
INSTALLATION
1.1 Unpacking the SWPIM-E1........................................................... 1-1
1.2 Installing the SWPIM-E1.............................................................. 1-2
1.3 LANVIEW LED Indications .......................................................... 1-4
1.4 Connecting to the Network .......................................................... 1-5
1.5 Completing the Installation .......................................................... 1-5
APPENDIX A
SPECIFICATIONS
A.1 Physical Properties......................................................................A-1
A.2 Network Interface ........................................................................A-1
A.2.1 Pinouts for the E1 Interface Connector ...........................A-2
A.3 E1 Cable Assembly .....................................................................A-2
A.4 Environmental Requirements ......................................................A-3
A.5 Regulatory Compliance ...............................................................A-3
SWPIM-E1 Installation Guide
ix
Contents
x
SWPIM-E1 Installation Guide
INTRODUCTION
Only qualified personnel should perform installation
procedures.
Welcome to the Cabletron Systems SWPIM-E1 Installation Guide. This
manual gives an introduction to the SWPIM-E1, lists features and
capabilities, details the cabling pinouts, and explains how to install the
SWPIM-E1.
The SWPIM-E1 provides a full and fractional E1 interface for a host
platform designed to receive the SWPIM (Sliding WAN Physical
Interface Module) architecture.
NOTE
The term “host platform” may be used to indicate the device or
module, such as the SSR-600 or the HSIM-SSR-600, into
which the SWPIM-E1 is installed.
USING THIS GUIDE
Read through this guide completely to understand the features and
capabilities of the SWPIM-E1.
A general working knowledge of WAN and Ethernet and IEEE 802.3 data
communications networks and their physical layer components is helpful
before using the SWPIM-E1.
STRUCTURE OF THIS GUIDE
This guide is organized as follows:
This Introduction provides preliminary information that will aid in using
this manual, lists technology and user’s guides that may help the user to
set up and manage the SWPIM-E1, gives an overview of the SWPIM-E1
and its features, and information on how to get help from Cabletron
Systems.
Chapter 1, Installation, provides instructions on how to install the device
into a host platform, and gives the LED indications.
SWPIM-E1 Installation Guide
xi
Introduction
Appendix A, Specifications, contains information on functionality and
operating specifications, connector pinout for the SWPIM-E1,
environmental requirements, and physical properties.
SWPIM-E1 FEATURES
Interfaces
The SWPIM-E1 can be installed into any Cabletron Systems product that
supports the SWPIM architecture, such as the SSR-600, or the
HSIM-SSR-600. Using software, the SWPIM-E1 is user-manageable
through the host platform. Refer to the host platform software user’s
manual for information on how to configure the SWPIM-E1 using
software.
The SWPIM-E1 uses a single RJ48 connector supporting the E1 interface.
Refer to Appendix A for the Cabletron Systems part number and pin
assignments for the E1 interface cable.
Internal CSU/DSU
The SWPIM-E1 provides an E1 interface that includes a built-in Channel
Service Unit/Digital Service Unit (CSU/DSU) for direct connection to an
E1 line. This SWPIM supports both full E1 and fractional E1 using
64 Kbps timeslots.
The E1 Channel Service Unit (CSU) meets the following specs:
•
Line Rate: 2.048 Mbps +/-50bps
•
Transmits according to G.703 pulse shaping for both short and long
haul
•
Receiver Sensitivity: +0 dB to -43 dB
•
Meets G.823 for jitter tolerance
•
Local Timing Capability
•
Supports Long Haul or Short Haul capability
xii
SWPIM-E1 Installation Guide
Introduction
The E1 Data Service Unit (DSU) meets the following specs:
•
E1 Framing Formats: FAS and CAS, with or without CRC4
•
FAS mode: Payload bandwidth is 1.984 Mbps
•
CAS mode: Payload bandwidth is 1.920 Mbps (channel 16 is reserved
for the signaling channel)
•
Line Coding: HDB3 or AMI
•
Supports both national and international bits for datalink
LEDs and Statistics
The SWPIM-E1 has two LEDs, to indicate link and status conditions.
Refer to Chapter 1 for more details.
The SWPIM-E1 also gathers statistics, such as bipolar violations and
frame errors, that are available through the management software.
RELATED MANUALS
The following Cabletron Systems manuals may help the user to set up and
manage the SWPIM-E1:
SSR-600 Installation Guide
HSIM-SSR-600 Installation Guide
6C105 SmartSwitch 6000 Overview and Setup Guide
Ethernet Technology Guide
Cabling Guide
The manuals referenced above can be obtained on the World Wide Web in
Adobe Acrobat Portable Document Format (PDF) at the following site:
http://www.cabletron.com/
SWPIM-E1 Installation Guide
xiii
Introduction
Cabletron Systems applicable software manuals for the SSR-600 and the
HSIM-SSR-600 host platforms (Cabletron Routing Software Manuals):
Bridging Configuration Guide
Event Logging System Message Guide
Network Interface Operations Guide
Routing Protocols Reference Guide
Routing Protocols User’s Guide
System Software Guide
ClearVISN Routing Configurator User’s Guide
Systems Network Architecture Guide
Quick Reference Guide
DTF (Data Trace Facility) User Guide
DOCUMENT CONVENTIONS
The following conventions may be seen in this document:
NOTE
TIP
!
Note symbol. Calls the reader’s attention to any item of
information that may be of special importance.
Tip symbol. Conveys helpful hints concerning procedures or
actions.
Caution symbol. Contains information essential to avoid
damage to the equipment.
CAUTION
Electrical Hazard Warning symbol. Warns against an action
that could result in personal injury or death due to an electrical
hazard.
xiv
SWPIM-E1 Installation Guide
Introduction
GETTING HELP
For additional support related to this device or document, contact
Cabletron Systems using one of the following methods:
World Wide Web
http://www.cabletron.com/
Phone
(603) 332-9400
Internet mail
support@cabletron.com
FTP
ftp://ftp.cabletron.com/
anonymous
your email address
Login
Password
To send comments or suggestions concerning this document, contact the
Cabletron Systems Technical Writing Department via the following
email address: TechWriting@cabletron.com
Make sure to include the document Part Number in the email message.
Before calling Cabletron Systems, have the following information
ready:
•
Your Cabletron Systems service contract number
•
A description of the failure
•
A description of any action(s) already taken to resolve the problem
(e.g., changing mode switches, rebooting the unit, etc.)
•
The serial and revision numbers of all involved Cabletron Systems
products in the network
•
A description of your network environment (layout, cable type, etc.)
•
Network load and frame size at the time of trouble (if known)
•
The device history (i.e., have you returned the device before, is this a
recurring problem, etc.)
•
Any previous Return Material Authorization (RMA) numbers
SWPIM-E1 Installation Guide
xv
Introduction
xvi
SWPIM-E1 Installation Guide
CHAPTER 1
INSTALLATION
Only qualified personnel should install the SWPIM-E1.
This chapter covers the following items:
•
Unpacking the SWPIM-E1 (Section 1.1)
•
Installing the SWPIM-E1 into the host platform (Section 1.2)
•
A description of the LANVIEW LED indications (Section 1.3)
•
Connecting the SWPIM-E1 to the network (Section 1.4)
•
What to do once the SWPIM-E1 is installed (Section 1.5)
1.1
UNPACKING THE SWPIM-E1
Use static electricity precautions when handling the SWPIM-E1.
1. Open the packing box and remove the SWPIM-E1.
2. Attach the antistatic strap (refer to the instructions in the antistatic
wrist strap package) before removing the SWPIM-E1 from the
antistatic packaging.
!
CAUTION
Failure to observe static safety precautions could cause
damage to the SWPIM-E1. Follow static safety handling rules
and wear the antistatic wrist strap shipped with the SWPIM-E1.
Do not cut the non-conductive bag to remove the device.
Damage could result from sharp objects contacting the device
or components.
3. Verify that the SWPIM-E1 is undamaged. Refer to Getting Help if
there is any damage to the device. Do not attempt to install the
SWPIM-E1 if it is damaged.
SWPIM-E1 Installation Guide
1-1
Chapter 1: Installation
1.2
INSTALLING THE SWPIM-E1
The SWPIM-E1 can be installed in any available open slot in the host
platform. To install the SWPIM-E1, proceed as follows:
1. Unfasten the screw and remove the blank panel covering the slot in the
host platform in which the SWPIM-E1 will be installed. See
Figure 1-1.
NOTE
It is not necessary to power down the host platform to install
the SWPIM-E1.
2. Ensure that the antistatic wrist strap is attached and used as
recommended.
!
Observe all precautions to prevent damage from Electrostatic
Discharge (ESD).
CAUTION
3. Remove the SWPIM-E1 from the plastic bag. (Save the bag in the
event the device must be removed from the host platform).
4. Hold the SWPIM-E1 with the faceplate facing away (right side up)
from the host platform. The 40-pin connector should be facing towards
the empty slot, with the wide part of the connector oriented down, as
shown in Figure 1-1.
5. Locate the rail guides inside the slot in which the SWPIM-E1 will be
installed. See Figure 1-1.
6. Install the SWPIM-E1 in the host platform by aligning the SWPIM-E1
with the rail guides in the host platform and sliding it in. Take care that
the SWPIM-E1 slides in straight and properly engages the backplane
host connector. Do not force the device.
1-2
SWPIM-E1 Installation Guide
Installing the SWPIM-E1
Rail Guides
Host Platform
View of Host Connector End
of SWPIM-E1
SWPIM-E1
Network Connector End
Thumbscrew
LNK
STS
SWPIM-E1
3059
Figure 1-1
Installing the SWPIM-E1 into the Host Platform
7. Fasten the SWPIM-E1 with the thumbscrew.
8. Replace power to the host platform, if necessary. Check to see that the
host platform LED indicators go to their normal configuration. If they
do not, remove the SWPIM-E1 from the host platform and contact
Cabletron Systems.
!
CAUTION
Do not connect any WAN cables until the software configuration
for the SWPIM-E1 has been done. The phone company can
shut down a line that has an unconfigured connection on it.
9. The SWPIM-E1 must be configured before the WAN connection is
made. Once the SWPIM-E1 has been configured, the host platform
must undergo a soft or hard restart in order for the SWPIM-E1 to be
recognized and for traffic to pass. Refer to the appropriate software
manual to configure the SWPIM-E1.
SWPIM-E1 Installation Guide
1-3
Chapter 1: Installation
1.3
LANVIEW LED INDICATIONS
Refer to Table 1-1 for the link LED indications for the SWPIM-E1.
Table 1-1
Link LED
Color
Indication
Off
Disabled or Not Configured
Red
No Link
Amber
Transmit or Receive Traffic
Green
Port is Active
Blinking Green
Port is in Test Mode
Refer to Table 1-2 for the status LED indications for the SWPIM-E1.
Table 1-2
Status LED
Color
Indication
Off
Normal or Disabled
Red
Receive Carrier Loss (RCL)
Amber
Receive Remote Alarm (RRA)
Receive Signaling All Zeros (RSA0)
Blinking Amber
Loopback Test Mode
Blinking Green
Receive Signaling All Ones (RSA1)
Receive Unframed All Ones (RUA1)
1-4
SWPIM-E1 Installation Guide
Connecting to the Network
1.4
CONNECTING TO THE NETWORK
Figure 1-2 depicts a typical configuration for the SWPIM-E1.
Site 1
SSR-600
WAN Cloud
SWPIM-E1
Site 2
SSR-600
SWPIM-E1
Figure 1-2
1.5
SWPIM-E1 Typical Configuration
COMPLETING THE INSTALLATION
After installation, the SWPIM-E1 will need to be configured for the
network. Refer to the host platform software documentation to set up and
manage the SWPIM-E1.
SWPIM-E1 Installation Guide
1-5
Chapter 1: Installation
1-6
SWPIM-E1 Installation Guide
APPENDIX A
SPECIFICATIONS
This section describes the environmental specifications and safety and
approval requirements for the SWPIM-E1. Cabletron Systems reserves
the right to change these specifications at any time without notice. Pinouts
and the E1 cable are also listed in this appendix.
A.1
PHYSICAL PROPERTIES
Dimensions:
1.91 H x 5.40 W x 19.05 D (cm)
0.75 H x 2.125 W x 7.50 D (in)
Weight (Unit):
.068 kg (0.15 lb)
Nominal current draw on +5V
supply from host platform:
150 mA
MTBF (Predicted):
10,119,716 hours
A.2
NETWORK INTERFACE
The connector for the RJ48 network port can be seen in Figure A-1:
12345678
strj45
Figure A-1
SWPIM-E1 Installation Guide
RJ48 Pinout
A-1
Appendix A: Specifications
A.2.1
Pinouts for the E1 Interface Connector
The network interface pin assignments for the network connector are
listed in Table A-1.
Table A-1
A.3
Pinouts for the E1 Interface Connection
Pin
Signal
1
Receive Ring
2
Receive Tip
3
Shield Ground
4
Transmit Ring
5
Transmit Tip
6
Shield Ground
7
Shield Ground
8
Shield Ground
E1 CABLE ASSEMBLY
Table A-2 lists Cabletron Systems part numbers for the interface cables
for the SWPIM-E1. A standard 20-foot cable is available or the customer
may specify the length of cable when ordering.
Table A-2
SWPIM-E1 Cable Part Numbers
Interface Cable
Cabletron Part Number
20-foot E1 Line Interface Cable
9372095-201
E1 Line Interface Cable
9372095-L2
1. Standard 20-foot E1 Line Interface Cable.
2. (L denotes length required in feet or meters). For example: 9372095-3
denotes a 3-foot cable; 9372095-3M denotes a 3-meter cable.
A-2
SWPIM-E1 Installation Guide
Environmental Requirements
The following table provides connector information for the SWPIM-E1
interface cable.
Table A-3
SWPIM-E1 Connector Information
Cabletron Systems interface cable part number
9372095-L
Description
E1 line interface cable
Connector 1
RJ45
Connector 2
RJ45
A.4
ENVIRONMENTAL REQUIREMENTS
Operating Temperature:
+5° to +40°C (41° to 104°F)
Non-operating Temperature:
-30° to +90°C (-22° to 194°F)
Operating Humidity:
5% to 90% (Non-condensing)
A.5
REGULATORY COMPLIANCE
Safety
EN 60950, IEC 950, 73/23/EEC
EMI
EN 55022 Class A,VCCI V-3, EN 50082-1,
AS/NZS 3548,89/336/EEC
Electromagnetic
Compatibility
(EMC)
Meets the EMC requirements of EN 50082-1
including:
IEC 801-2 (ESD), IEC 801-3 (Radiated
Susceptibility), and IEC 801-4 (EFT/B)
Telecom
CTR4, CTR12, TS014
SWPIM-E1 Installation Guide
A-3
Appendix A: Specifications
A-4
SWPIM-E1 Installation Guide
Download PDF