AT&T | E6014B | User`s manual | AT&T E6014B User`s manual

Quick start guide
E6012B/E6013B/E6014B/E3813B
5.8 GHz cordless telephone/
answering system with caller ID/
call waiting
TONE
MUTE
REDIAL
DELETE
PAUSE
Installation and setup
Choose a central location close to a telephone jack and a power outlet not
connected to a wall switch. The telephone base can be placed on a flat surface or mounted on a standard wall plate. For optimum range and better
reception, place the telephone base in a high and open location.
Avoid placing the telephone base too close to:
• Communication devices such as: personal computers, computer routers, television sets, VCRs, wireless routers (wireless broadband, wi-fi, or 802.11) or
other cordless telephones.
• Excessive heat sources.
• Noise sources such as a window with traffic outside, motors, microwave
ovens, refrigerators, or fluorescent lighting.
• Excessive dust sources such as a workshop or garage.
• Excessive moisture.
• Extremely low temperature.
• Mechanical vibration or shock such as on top of the washing machine or
work bench.
1. Plug one end of the telephone line
cord into the telephone jack at the
bot­tom of the telephone base.
5. Plug the other end
2. Plug the small end of the larger power adapter
into the power jack at the bottom of the telephone
base.
3. Route cords through slots.
of the telephone line
cord into a telephone
jack.
Telephone line cord
DSL filter
(Optional for DSL users, see number
four in the NOTES section, below.)
4. Plug the large end of the larger power
adapter into an electrical outlet not controlled by a wall switch.
NOTES:
1. The mounting bracket must be used for both tabletop use and wall mounting positions.
2. Use only the power cord supplied with this product, if you need a replacement, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada dial 1 (866) 288-4268.
3. Be sure to use an electrical outlet not controlled by a wall switch.
4. This power adapter is intended to be plugged into a vertical wall outlet or a floor outlet. The
prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-thetable or cabinet outlet.
5. If you receive high speed internet through your telephone line (commonly referred to as DSL),
and you are experiencing interference during telephone conversations and/or your caller ID
features are not functioning properly, install a DSL filter to the telephone line between the telephone base and the telephone wall jack. Contact your DSL service provider for a DSL filter.
Installation and setup
After battery installation, the battery may have enough charge to allow some
calls. For best performance, place the handsets in the telephone base or the
charger and allow to charge for 16 hours before use.
You can keep the battery charged by returning the handsets to the telephone
base or the charger after use. When the battery is fully depleted, a recharge
takes about 12 hours. The average talk time on a fully charged battery is
about eight hours, and the standby time is approximately five days. Actual
battery life depends on usage conditions and age of battery.
1. Plug the battery securely
into the plug inside the
handset battery compartment, match­ing the colorcoded label.
2. Place the battery
and wires neatly inside
the compartment.
4. The battery may have
enough charge to allow
for some calls. For best
performance, place handset in telephone base or
charger to charge for at
least 16 hours before first
use.
3. Slide battery com­partment
cover towards the center
until it clicks into place.
To replace the battery,
press in and push outward
on the tab to open the battery compartment cover.
Lift out the old battery
and disconnect it from the
compartment. Follow the
instructions on this page to
install and charge the new
battery.
TONE
MUTE
REDIAL
DELETE
PAUSE
Caution: Use only the supplied rechargeable battery or replacement battery (model 27910,
part number 89-0099-00-00). To order a replacement battery, visit our website at
www.telephones.att.com or call 1 (800) 222-3111. In Canada dial 1 (866) 288-4268.
Quick reference guide
Handset
CENTER
UP
CID
Press to display caller ID
information.
RIGHT
LEFT
DOWN
PHONE/FLASH
Press to make or
answer a call. During
a call, press to receive
an incoming call if call
waiting is activated.
MENU/SELECT
Press to display the menu. Once
in a menu, press to select an item
or save an entry or setting. Press
or
to scroll up or down
while in menus. While entering
names or numbers, press
or
to move the cursor.
MUTE/DELETE
While on a call, press to
mute microphone. While
reviewing the call log,
press to delete an individual entry, or press and hold
to clear the caller ID log.
While predialing, press to
delete digits from a string.
DIR
Press to display directory entries.
OFF/CLEAR
Press to cancel an operation, back
up to the previous menu, or exit
the menu display.
SPEAKER
Press to activate handset speakerphone.
Press again to resume
normal handset use.
REDIAL/PAUSE
Press to view redial memory. While
entering numbers, press and hold
to insert a dialing pause.
TONE
MUTE
REDIAL
DELETE
PAUSE
INT
Press to initiate an intercom conversation or transfer a call.
Feature menu
shows a highlighted item
DIRECTORY
Feature menu
DIRECTORY
CALL LOG
SETTINGS
SOUNDS
DISPLAY
RINGER VOLUME
Menu
Using menus
Press
items.
to scroll through menu
Press MENU/SELECT to select or modify a highlighted item.
Press OFF/CLEAR to cancel an operation, back up to the previous menu,
or exit the menu display
NOTE: For more information, please refer to the user’s manual.
Quick reference guide
Telephone base
CHARGE
VOICEMAIL
On when the cordless handset is
properly positioned to charge in
the telephone base.
IN USE
On when handset is in use, the
answering system is answering an
incoming call or you are registering
a handset.
Flashes while an incoming call is
ringing, when another telephone is
in use on the same line, or you are
de-registering a handset from the
telephone base.
SETUP
Flashes when you have
new voice mail (different
voice mail system from the
answering system on the
telephone base, requires
voice mail service from
your local telephone company.)
HANDSET LOCATOR
Press to make handsets
beep.
ANNC
Press to hear setup
options.
Press to review or record
announcement; press
again to quit.
MESSAGE COUNTER
Number of messages (or
during playback, message
number currently playing).
RECORD
Press to record a memo
or after pressing ANNC
to record an outgoing
announcement.
CLOCK
Press to review or set
clock.
X/DELETE
Press to delete message
currently playing; press
and hold to delete all
old messages.
Press to repeat message.
Press twice to hear previous message.
/REPEAT
Press to repeat message; press twice to
play previous message.
PLAY/STOP
Press to start or stop
message playback.
NOTE: For more information, please refer to the user’s manual.
ANSWER ON
Press to turn answering
system on or off.
VOLUME
Press to adjust playback
volume.
/SKIP
Press to skip message.
www.telephones.att.com
Copyright © 2007 Advanced American Telephones. All rights reserved.
AT&T and the AT&T logo are trademarks of AT&T Knowledge Ventures,
licensed to Advanced American Telephones. Printed in China. Issue 4 AT&T 02/07.
96-006310-010-100
Download PDF