Zanussi | ZK 24 FX | Specifications | Zanussi ZK 24 FX Specifications

ZANUSSI
ZK 24 FX
FRIDGE FREEZER
INSTRUCTION BOOKLET
1
Important Safety Information
These warnings are provided in the interests of your safety. Ensure that you understand them all
before installing or using this appliance. If you are unsure of the meanings of these warnings
contact the Customer Care Department.
Installation
•
This appliance is heavy. Care should be taken
when moving it.
•
Do not place carbonated or fizzy drinks in the
freezer compartment.
•
It is dangerous to alter the specifications or
attempt to modify this product in any way.
•
•
Ensure that the appliance does not stand on
the electrical supply cable. If the supply cable
is damaged, it must be replaced by a cable
available from your local Service Force
Centre.
Ice lollies can cause frost/freezer burns if
consumed straight from the freezer compartment.
•
Do not remove items from the freezer compartment if your hands are damp/wet, as this
could cause skin abrasions or frost/freezer
burns.
•
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
•
Bottles and cans must not be placed in the
freezer compartment as they can burst as the
contents freeze.
•
Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall, but leaving the
required distance for ventilation, as stated in
the installation instructions.
•
Manufacturers’ recommended storage times
should be adhered to. Refer to the relevant
instructions.
•
The appliance should be left for 2 hours after
installation before it is turned on, in order to
allow the refrigerant to settle.
•
Before cleaning, always switch off the appliance and disconnect from the electrical
supply.
•
When unplugging always pull the plug from
the mains socket, do not pull on the cable.
Maintenance and Cleaning
Child Safety
•
Do not allow children to tamper with the
controls or play with the product.
•
Keep all packaging material away from
children.
During Use
2
•
This appliance is designed for domestic use
only, specifically for the storage of edible
foodstuffs only. It is not intended for commercial or industrial use.
•
Containers with flammable gases or liquids
can leak at low temperatures. Do not store
any containers with flammable materials,
such as spray cans, fire extinguisher refill
cartridges etc. in the refrigerator.
•
Frozen food should not be refrozen once it
has thawed out.
Servicing
•
This product should be serviced by an authorised engineer and only genuine spare parts
should be used.
•
Under no circumstances should you attempt
to repair the appliance yourself. Repairs
carried out by inexperienced persons may
cause injury or serious malfunction. Contact
your local Zanussi Service Force Centre.
Contents
Instructions for the Installer
Instructions for the User
Important Safety Information
2
Technical Specifications
14
Description of the Appliance
Thermostat Controls
Ice Maker
Water Dispenser
4
5
5
5
Door Removal
To remove the Freezer Door
To remove the Fridge Door
15
15
16
Using the Appliance
Before use
To Start the Appliance
Food Storage
Frozen Food Storage
Freezing Fresh Food
Ice and Water Dispenser
6
6
6
6
7
7
7
Installation Requirements
Ventillation
Levelling
17
17
17
Electrical Connection
18
Water Connection
19
Hints and Tips
Food Storage
Energy Saving Advice
In the event of a Power Failure
8
8
8
8
Maintenance and Cleaning
Internal Cleaning
Defrosting
Changing a Light Bulb
Ice Dispenser
External Cleaning
When the appliance is not in use
9
9
9
9
9
10
10
Something Not Working ?
11
Service & Spare Parts
12
Customer Care
12
Guarantee Conditions
13
3
Description of the Appliance
A
F
G
B
H
C
I
D
J
E
K
F
L
M
4
Freezer Compartment
Refrigerator Compartment
A
B
C
D
E
F
F
G
H
I
J
K
L
M
Control panel
Pizza shelf
Water, Ice Cubes & Crushed Ice
Slide out wire shelf
Adjustable storage compartment
Slide out freezer basket
Control panel
Dairy compartment
Flip & Slide glass shelf
‘Spillsafe’ adjustable shelf
Deli Drawer
Adjustable door storage compartments.
Crisper
Meat drawer
Thermostat Controls
Ice Maker
A thermostat control is located in the top panels inside
the freezer and refrigerator compartments, which
controls the temperature inside the freezer and refrigerator respectively.
The ice maker is located behind the baffle in the top
of the freezer.
The Freezer Temperature Control
The thermostat control located inside the freezer
regulates the temperature within the freezer
compartment. A change in the control setting in the
freezer compartment could affect the temperature in
the refrigerator compartment under certain
circumstances.
To start ice making, lift the flap to allow access to the
wire signal arm and lower it to the ‘ON’ position.
Off
Coldest
Cold
•
Lift Up
Lower
- Switches off cooling to the appliance
- Maximum coldness
- Minimum coldness
An intermediate position is usually the most suitable,
although the temperature will be affected by:
•
•
•
Once the freezer temperature is cold ice making can
be started.
Room temperature
How often the door is opened
How much food is stored
Position of the appliance
In determining the correct temperature control setting
all these factors have to be considered and some
experimentation may be necessary.
When altering the temperature settings, allow 24
hours for the temperature to stabilise before making
further changes.
Important
Turning the freezer control to “OFF” will shut down
cooling in BOTH the refrigerator and the freezer
compartments.
Wire Signal Arm
To stop ice making raise the wire signal arm to the
“OFF” position.
Water Dispenser
A water tank is located at the back of the refrigerator
compartment and holds approximately 1.5 ltrs (48fl
oz) of water.
To fill the water tank after installation:
Ensure the selector is positioned to “Water”. Draw
and discard one glass of water. This action will fill the
tank, it will take approximately 1 ½ minutes. Continue
to draw and discard 7 more glasses of water to ensure
that all plumbing connections have been rinsed.
The tank automatically refills as water is dispensed.
The Refrigerator Temperature Control
The thermostat control located inside the fridge
regulates the temperature within the fridge compartment, by regulating the cold air flow.
A setting midway between coldest and cold is usually
the most suitable, although some experimentation may
be necessary to obtain the correct temperature.
Coldest
Cold
To ensure fresh tasting water, we recommend you use
the water dispenser daily.
- Maximum coldness
- Minimum coldness
5
Using the Appliance
This appliance is designed for domestic use
only, specifically for storage of edible foodstuffs.
This appliance is designed to operate in
ambient temperatures (surrounding air temperature) between 16oC and 32oC. If these
temperatures are exceeded i.e. colder or
warmer, the appliance will not operate correctly.
Food Storage
To obtain the best performance from your appliance,
do not store warm food or evaporating liquids in the
refrigerator. Cover or wrap food particularly if it has a
strong flavour.
Refrigerator Shelves
To adjust the shelves in the refrigerator compartment,
lift the shelf up, unhook and remove (ensure that any
blue transit packaging has been removed), reposition
as required.
Before Use
Remove all securing tapes, and any transit packaging.
Wash the inside of the appliance with lukewarm water
with a little bicarbonate of soda added (5ml to 0.5 litre
of water). Do not use soap or detergent as the smell
may linger. Dry the appliance thoroughly.
Door Shelves.
The door shelves can be removed for cleaning or
adjustment. Lift upwards and reposition as required.
If required the tall bottle retainer can be fitted on the
shelf.
Do not use detergents, abrasive powders, highly
perfumed cleaning products, wax polishes or products
containing alcohol.
Crisper
Use the Crisper for storing fresh fruit and vegetables.
Vegetables should be washed and dried before being
placed into the Crisper. A variable humidity control
allows you to adjust the storage environment in the
Crisper.
To Start the Appliance
6
1.
Allow the appliance to stand for 2 hours after
installation.
2.
Plug in the appliance and switch on at the mains
supply. DO NOT use an extension lead or adaptor.
3.
Set the fridge and freezer controls to MIDWAY
between cold and coldest. Adjust after 24 hours if
necessary.
4.
Allow the refrigerator to operate with the doors
closed for at least 8 hours before loading with
food.
Chilled Meat Drawer
Meat, fish and poultry can be kept fresh for longer if
placed in the meat drawer. To obtain a cooler temperature slide the control on the side of the cabinet to
coldest.
Wine Rack
To install the wine rack, slide the rack onto either side
of the shelf with the curve facing inwards. To remove,
slide the wine rack out.
Frozen Food Storage
Ice & Water Dispenser
The freezer door has
storage compartments and
is suitable for the storage of commercially frozen
food. Follow the food manufacturer’s storage
instructions.
The ice and water dispenser on the freezer door
dispenses chilled water and ice.
The inner freezer compartment is
and suitable
for storage of commercially frozen food and for
freezing fresh foods.
Frozen food can be stored in any basket or drawer of
the freezer compartment
Do not exceed the storage period indicated by the
food manufacturer.
To operate the dispenser:
1.
Push the selector to “Water”, “Ice Cubes” or
“Crushed Ice”.
2.
Press a glass against the dispensing arm.
3.
Remove the glass to stop dispensing.
Note:
When dispensing ice, release the dispensing
arm before the glass is full and allow the ice
chute to clear before removing glass.
Do not open the door frequently or leave it open
longer than is necessary.
The drip tray will catch and evaporate small spills.
The drip tray is removable and dishwasher safe.
Freezing Fresh Food
DO NOT pour water directly into the drip tray, it
is not a drain.
The maximum quanitity of food you can freeze in 24
hours is 7Kg.
When freezing fresh foods, turn the thermostat control
in the freezer to Coldest 2 hours before loading fresh
foods.
Place the food to be frozen on the top shelf or in the
top drawer.
IMPORTANT
To ensure fresh tasting water we recommend the water
dispenser is used daily.
If the water tank is not used for more than one week
flush the tank through, by drawing and discarding
approximately 8 glasses of water.
When the food is frozen turn the thermostat control
back to its original position.
Do not put carbonated liquids, (fizzy drinks
etc), in the freezer compartment.
Water ices, if consumed immediately after
removal from the freezer, can cause low
temperature skin burns.
Do not remove items from the freezer if your
hands are damp/ wet as this could cause skin
abrasions or frost / freezer burns.
7
Hints and Tips
Food Storage
In the event of a Power Failure
•
To obtain the best results from your appliance.
neither hot foods nor liquids which may evaporate, should be placed in the larder compartment.
•
Avoid buying frozen food if you cannot store it
straight away. The use of an insulated container is
advisable. When you arrive home place the
frozen food in the freezer immediately.
If there is a power failure during the storage of frozen
foods, keep the door closed. If the temperature within
your freezer should rise do not refreeze the food
without checking it’s condition. The following guidelines should assist you.
•
Keep the time between buying chilled food and
placing it in your fridge as short as possible.
•
Do not push food together too much, try to allow
air to circulate around each item.
•
Do not store food uncovered.
•
Ensure that food placed in the freezer is dated and
labelled and used in date order to ensure that food
is consumed at its best.
•
Remove suspect food from your refrigerator and
clean, refer to the chapter ‘Maintenance and
Cleaning’.
Energy Saving Advice
8
•
Do not install the cabinet close to sources of heat,
such as a cooker, dishwasher or radiator.
•
Locate the appliance in a cool well ventilated
room and make sure that the air openings of the
cabinet are not obstructed.
•
Avoid unnecessary frosting in the cabinet by
packing all foodstuffs into airtight packages
before placing them in the freezer.
•
Always leave warm food to cool down to room
temperature before placing in the fridge or
freezer.
•
Food which is to be frozen (when cool) should be
placed in the fridge before being transferred to
the freezer.
•
Thaw frozen food in the fridge. This will ensure
safer defrosting of foods and reduce the work of
the refrigeration unit.
•
Try to avoid keeping the door open for long
periods, or opening the door too frequently as
warm air will enter the cabinet, and cause the
compressor to switch on unnecessarily often.
•
Ensure there are no obstructions preventing the
door closing properly.
Ice Cream:
Once thawed should be discarded.
Fruit and Vegetables:
If soft should be cooked and used up.
Bread and Cakes:
Can be refrozen without danger.
Shellfish:
Should be refrigerated and used up quickly.
Cooked Dishes:
i.e. casseroles, should be refrigerated and used.
Large Pieces of Meat:
Can be re-frozen providing there are ice crystals
remaining within them.
Small Joints:
Should be cooked and then re-frozen as cooked
dishes.
Chicken:
Should be cooked and re-frozen as a fresh dish.
Maintenance and Cleaning
Before any maintenance or cleaning work is
carried out DISCONNECT the appliance from
the ELECTRICITY supply.
Ice Dispenser
Clean the the dispenser and storage bin periodically.
1.
Internal Cleaning
Remove storage bin. Stop ice production (raise
signal arm).
Clean the inside and accessories with warm water and
bicarbonate of soda (5ml to 0.5 litre of water). Rinse
and dry thoroughly.
Regularly check the door seals and wipe clean to
ensure they are clean and free from debris.
Do not use detergents, abrasive powders,
highly perfumed cleaning products, wax
polishes or cleaning products containing
bleach or alcohol.
Wire Signal Arm
2.
Your appliance is frost free, which means there is no
need to manually defrost your appliance as this will be
carried out automatically.
Empty and clean the storage bin with a cloth and
mild solution of washing up liquid and water. DO
NOT submerge the bin in water or use abrasive
cleaners.
3.
Remove ice chips, clean the shelf and ice chute.
4.
Replace storage bin.
Changing a Light Bulb
5.
Begin ice production again (lower wire signal
arm).
Defrosting
Ensure the appliance has been disconnected
from the mains supply before changing a light
bulb. Turning the thermostat control to the
“OFF” position does not disconnect the
appliance.
Important
The Storage bin should be removed if:
•
A power failure causes the ice in the machine to
melt and then refreeze, as they may cause the ice
making mechanism to jam when the power is
resumed.
•
The ice maker is not used frequently.
It is adviseable to wear gloves or use a cloth
when changing a light bulb.
Refrigerator Compartment
Unscrew the old bulb and replace with a 220-240 Volt,
40W bulb with an E27 screw thread.
Freezer Compartment
Remove the hexagonal nut retaining the bulb cover.
Unscrew the old bulb and replace with a 220-240 Volt,
40W bulb with an E27 screw thread.
Do not put fingers up the ice chute, there may
be sharp edges.
DO NOT rotate the spiral rod, when replacing
the ice bin. To realign the spiral rod, rotate it
in 90o turn until the ice bin fits into place with
the driver mechanism.
Ice & Water Dispenser
Unscrew the old bulb and replace with a 220-240 Volt,
7W bulb with an E14 screw thread.
9
External Cleaning
Do not use abrasive products.
There may be sharp edges on the underside of
the product so care should be taken when
cleaning.
Wipe the outer cabinet with a soft cloth and warm
soapy water.
Stainless Steel Doors
Wipe the stainless steel doors with a soft cloth and
warm soapy water. Rinse with clean water and dry
with a soft cloth.
Clean any stubborn marks with an ammonia soaked
paper towel and rinse and dry. Alternatively use a
proprietary stainless steel cleaner, following the
manufacturer’s instructions.
When the appliance is not in
use
If the appliance is not in use for a long period.
•
Remove all food and ice.
•
Turn the thermostat controls to the OFF position
•
Disconnect from the electricity supply.
•
Raise the wire signal arm (of the ice maker) to
the “OFF” position.
Wire Signal Arm
•
•
•
10
Turn off the water supply.
Clean the interior thoroughly
Leave both doors open to prevent any odours or
mould build-up.
Something Not Working ?
Some problems are due to lack of simple maintenance or oversights, which can be solved easily without calling
out an engineer. If your appliance does not function correctly, please carry out the following checks before
contacting your local Service Force Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect
use or installation, a charge will be made, even if the appliance is under guarantee.
Symptom
Solution
No power to the appliance
Check there is power
Check there is not a power cut by checking the
household lights.
Check the fuse has not blown
The internal light in the fridge or freezer does not
come on
Ensure that the bulb has not blown.
Replace the bulb if it has blown
Check the door light switch is not jammed.
The temperature in the fridge or freezer section is too
high
Check the thermostat is turned to the correct setting
relative to ambient conditions.
Check the ambient temperature is within the
appliance’s operating limits of 16oC to 32oC.
Relocate the appliance if necessary.
The foods in the refrigerator are frozen
Is the temperature control set on high ?
The compressor runs continuously
Check the thermostat is turned to the correct setting
relative to ambient conditions.
Check the doors are closed properly.
Large quanitites of food have recently been placed
in the cabinet and / or door has been frequently
opened.
There is an unpleasant odour in the fridge
Check that air ventilation is not obstructed.
The food was not covered.
The freezer door will not open
Has the door just been opened ? If so leave for a
few minutes to allow the air pressure to equalise.
If after the above checks there is still a fault call your local Service Force Centre.
11
Service & Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare parts please contact your local
Zanussi Service Force Centre by telephoning:
08705 929 929
Your call will be routed to the Service Force Centre covering your post code area. The address of your local
Service Force Centre is detailed in the accompanying Customer Care Book.
Before calling out an engineer to a fault, please ensure you have read the details under the heading ‘Something
Not Working?’. If you call out an engineer to a fault caused by incorrect use or installation, a charge will be
made, even if the appliance is under guarantee.
When you contact the Service Centre you will need to give the following details:
1.
2.
3.
4.
5.
Your address and post code
Your telephone number
Clear and concise details of the fault
The model and serial number of the appliance (found on the rating plate)
The purchase date
Customer Service
For general enquiries concerning your Zanussi appliance or for futher information on Zanussi products, please
contact our Customer Care Department:
Customer Care Department
Zanussi
55 - 77 High Street
Slough
Berkshire
SL1 1DZ
08705 727 727
12
Guarantee Conditions
Standard guarantee conditions: European Guarantee:
We Zanussi undertake that if within 12 months of the
date of the purchase this Zanussi appliance or any part
thereof is proved to be defective by reason only of
faulty workmanship or materials, the company will, at
our option repair or replace the same FREE OF
CHARGE for labour, materials or carriage on
condition that:
·
The appliance has been correctly installed and
used only on the electrical supply stated on the
rating plate.
·
The appliance has been used for normal domestic
purposes only, and in accordance with the manufacturer’s instructions.
If you should move to another country within Europe
then your guarantee moves with you to your new
home subject to the following qualifications:
·
The guarantee starts from the date you first
purchased your product.
·
The guarantee is for the same period and to the
same extent for labour and parts as exists in the
new country of use for this brand or range of
products.
·
This guarantee relates to you and cannot be
transferred to another user.
·
Your new home is within the European Community (EC) or European Free Trade Area
·
The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any
person not authorised by us.
·
The product is installed and used in accordance
with our instructions and is only used domestically, i.e. a normal household.
·
All service work under this guarantee must be
undertaken by a Zanussi Service Force Centre.
·
The product is installed taking into account
regulations in your new country.
·
Any appliance or defective part replaced shall
become the Company’s property.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside
these hours in which case a premium will be charged.
Exclusions
This Guarantee does not cover:
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
·
Costs incurred for calls to put right an appliance
improperly installed or calls to appliances outside
the United Kingdom.
·
Appliances found to be in use within a commercial environment, plus those which are the subject of rental agreements.
·
Products of Zanussi manufacture which are not
marked by Zanussi.
Before you move please contact your nearest Customer Care Centre, list below, to give them details of
your new home. They will then ensure that the local
Service Organisation is aware of your move and able
to look after you and your appliances.
France
Germany
Italy
Sweden
UK
Senlis
Nurenberg
Pordenone
Stockholm
Slough
+33 (0)3 44 62 29 99
+49 (0)911 323 2600
+39 (0)1678 47053
+46 (0)8 738 79 50
+44 (0)1753 219897
This guarantee is in addition to your statutory and
legal rights.
13
Installation Instructions
Technical Specifications
Dimensions
Height
Width
Depth
Voltage
1702mm
895mm
743mm
Capacity
Gross
Net
677 Litres
Fridge
Freezer
Freezer
Freezing Capacity / 24 hours
420 Litres
24 Litres
122 Litres
Frequency
50 Hz
Average Daily Units of Electricity*
2.4Kw
*This figure is based on standard test results in the
European Standard EN. Actual consumption will
depend on how the appliance is used and where it is
located.
7 Kg
162o
147o
Important
Please ensure that when the appliance is installed it is
easily accessible for the engineer in the event of a
breakdown.
14
230-240V
Door Removal
It may be necessary to remove the doors to allow for
the delivery or installation of the appliance.
To remove the freezer door:
1.
Lift off the plastic top hinge cover.
1
2.
Trace around top hinge with soft lead pencil for
ease of relocation.
2
3.
Grip the corner and centre of base grille and pull
off.
3
4.
Remove bottom hinge cover screw. Remove
cover.
4
5.
Gently bend wiring harness connector to disconnect.
NOTE:Pull on plastic connectors, NOT on wires.
5
6.
7.
8.
9.
Disconnect water line by pushing in on grey
collar, forcing elbow down off water line from
door.
Open the door to its full position. Tape lower
hinge securely to door bottom. Loosen, but DO
NOT REMOVE lower screw on bottom hinge.
Remove top screw from bottom hinge.
6
7
Remove top hinge screws from the freezer with
an anti-clockwise motion.
Note: Hinge has a minimal spring load. Hold
bracket when removing last screw.
8
Lift door off bottom hinge screw.
9
15
To remove the fridge door
10. Lift off the top plastic hinge cover.
10
11. Remove top hinge screws
11
12. Lift refrigerator door off bottom hinge. If necessary you can remove bottom hinge by removing
grill and hinge mounting screws.
12
13. Set the refrigerator in final location.
14. Refit doors with all shims and washers in original
order and tighten screws.
Note: Do NOT over tighten .
15. To reinstall water line elbow, grip door tube
firmly and push up on elbow until it touches the
black mark on the tube and comes to a stop. This
step is critical to ensure that the water line does
not leak.
16. Check door alignment. The space between the
door and cabinet edge (gasket space) should be
¾” at the top hinge.
16
13
14
Installation Requirements
To ensure correct operation of this appliance, it must not be located where the temperatures will fall below 16oC
(61oF) or rise above 32oC (90oF).
For correct operation this appliance must be :
• In a dry atmosphere
Avoid the following locations:
• Unheated kitchen
•
Out of direct sunlight
•
Outhouse
•
Away from extreme temperature (not next to a
cooker or other source of heat).
•
Conservatory
•
Garage
•
The appliance is heavy when fully loaded, and
must be stood on a strong floor.
Ventilation
Allow a 25mm (1 inch) space behind and above the
appliance for ventilation.
In a recessed installation, allow an extra 10 - 15mm
(½ inch) on each side for ease of installation. If the
side of the unit is to be placed against a wall, allow
43mm (1¾ inch) space for proper door opening.
Levelling
The appliance has four castors. The two castors at
the front of the appliance should be adjusted to
ensure that the cabinet is level.
To adjust the front castors:
1.
Open both doors.
2.
Remove the base grille by pulling it straight out.
3.
Adjust the casters by turning the adjusting bolt
with a spanner until the refrigerator is level and
stable.
If the freezer door is higher than the refrigerator
door, raise the right corner and/or lower the left
corner until the doors align across the top of the
cabinet.
If the refrigerator door is higher than the freezer
door, raise the left corner and/or lower the right
corner until the doors align cross the top of the
cabinet.
The rear castors are not adjustable.
4.
Check both doors to ensure that the seals touch
the cabinet on all sides.
5.
Replace the bottom grille by lining up the retainers with the holes and pushing the grille straight
on.
Turn the bolt clockwise
to raise
Turn the bolt
anti-clockwise to lower
17
Electrical Connection
Any electrical work required to install this
appliance must be carried out by a qualified
electrican or competent person.
This appliance must be earthed.
The manufacturer declines any liability should
these safety measure not be observed.
Electrical Requirements
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance
rating plate.
The appliance is supplied with a 13 amp plug fitted. In
the event of having to change the fuse in the plug
supplied, a 13 amp ASTA approved (BS 1362) fuse
must be used.
Should the plug need to be replaced for any reason.
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow
: Earth
Blue
: Neutral
Brown
: Live
The wire coloured green and yellow must be
connected to the terminal marked with the letter “E”
or by the earth symbol
or coloured green and
yellow.
The wire coloured blue must be connected to the
terminal marked ‘N’ or coloured black.
The wire coloured brown must be connected to the
terminal marked “L” or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must be
secure over the outer sheath.
Important
If the mains supply cable is damaged, it must be
replaced by a cable available from your local Service
Force Centre.
18
Water Connection
The ice maker water supply tube must be connected a
a drinking water supply.
The water supply must have a water pressure within
the following limits:
Minimum pressure 2.1 bars (30psi)
Maximum pressure 8.3 bars (120 psi)
The quality of the ice is dependent upon the water
quality. It is recommended that the ice maker water is
not softened. If the ice maker is connected to softened
water ensure the softener is maintained and working
correctly.
Remove retaining screws
To connect the water supply:
1.
Turn off the water supply and disconnect the
appliance from the power supply.
2.
Remove the three retaining screws and bend the
black cover at the perforations.
3.
Connect the water hose supplied to the water
supply connection.
Bend back the
black cover
Water supply
connector
4.
Turn on the water supply and check all connections for leaks.
5.
Pull the black cover and replace the three retaining screws.
6.
Plug in the appliance.
NOTE
• Ice production will begin when the freezer
reaches normal operating temperature. See page 5
“Ice Maker” and “Water Dispenser”.
•
Air in the plumbing lines after installation may
cause the ice maker to cycle two or three times
before making a full tray of ice.
•
New plumbing may cause ice to be discoloured or
have poor flavour. Discard ice made during the
first 24 hours.
Replace retaining screws
19
Download PDF