XP-600 Installation Manual

XP-600 Installation Manual
®
XP-600
Control Panel/Communicator
Installation Instructions
© NAPCO 1997
Wi846c
page 1
WI846C 8/97
Tuesday, September 16, 1997 10:36
WI846C XP-600 Installation Instructions
7DEOH RI &RQWHQWV
*HQHUDO ,QIRUPDWLRQ
;3 )HDWXUHV
General Information..........................................2
GEM-P800 Features.........................................2
Specifications ...................................................3
UL Compatible Smoke Detectors......................4
Listings and Approvals .....................................4
Ordering Information ........................................4
Optional Accessories........................................4
Programming the Panel....................................5
Installation........................................................6
Wiring...............................................................6
Keypad Operation ............................................7
Panel Operation ...............................................8
Bypassing ........................................................9
User Program Mode .........................................10
GEM-P800 Commands ....................................10
Dealer Commands ..........................................11
Wireless Operation (Signal Strength) .............12
Zone Features ..................................................13
System Times ..................................................14
System Features ..............................................15
Telephone Number 1 Programming..................16
Backup Telephone Programming .....................17
Pager Programming .........................................18
Telephone Number 3 Programming..................18
Report Codes ...................................................19
Enhanced Communicator Features ..................19
Wireless ...........................................................20
Downloading.....................................................21
Dealer Programming ........................................22
System Troubles ..............................................23
Troubleshooting................................................25
GEM-P800 WIRING DIAGRAM ........................27
The NAPCO EXPRESS XP-600 control panel provides up to 6 hardwired/wireless zones and 2-wire
fire. Up to six 4-digit user codes can be programmed.
Ambush, when selected, uses User 6 code as an
Ambush code.
Control Panel
The XP-600 is wireless ready. When used with a
GEM-RECV-XP8 receiver, the control panel can support up to 6 wireless zones, 4 wireless smoke detectors and 4 Keyfobs.
The RPX-6 keypad provides complete control of the
XP-600 control panel. Information on system status,
bypassed zones, system troubles etc. can be viewed
at the keypad.
The control panel can be easily and quickly programmed from the keypad. The panel can also be
locally or remotely downloaded using PCD3000 software and a PCI 2000/3000 interface or PCL2000A
local Download cable. See Downloading Section (pg.
5) for more information.
• 6 Zones
• 2-wire Fire Zone
• 3 Keypad Panics
• Wireless Ready
• Bell Supervision
• Line Cut Detection
• Answering Machine Override (Second Call)
• 50 Event Log
Communicator
• 2 Telephone Numbers
• Backup Reporting
• Pager Format
• Point ID Format
• Individually Report 6 Users
• Opening after Alarm Report (Cancel Code)
NAPCO Security Systems, Inc.
333 Bayview Avenue z Amityville, New York 11701
For Sales and Repairs, call Toll Free: (800) 645-9445
For Technical Assistance, Contact the NAPCO Toll Free Helpline (800) 645-9440
2
Wi846c
page 2
Tuesday, September 16, 1997 10:36
6SHFLILFDWLRQV
&XUUHQW 9ROWDJH 5DWLQJV
Alarm Output ---------------------------Burg:
Fire:
/RRS &KDUDFWHULVWLFV
12 VDC, 2A (max.)
12 VDC, 65 mA
Output Current Limiting --------------Burg/Fire:
AUX Power:
2.25 A
750 mA
Combined Standby Current: --------350 mA maximum
(Remote PWR, AUX Output, PGM)
4 Hour Standby:------------------------350 mA Standby Current
Bell Output 65 mA
(Using Rechargeable 12 VDC 4 AH BATTERY, minimal requirement)
24 Hour Standby: ----------------------120 mA Standby Current
Bell Output 95 mA
(Using Rechargeable 12 VDC 7 AH BATTERY, Optional)
7UDQVIRUPHU DQG %DWWHU\
Required Transformer: --------------NAPCO TRF12 OR
BASLER 16.5 VAC 20VA
Required Battery: ---------------------12V 4 AH Rechargeable
Change Battery every 5 years or as required
Loop Voltage: ------------------------- 5 Volts
Loop Current :-------------------------- Zones 1, 2, 3: 0.9 mA
Zones 4, 5, 6: 0.5 mA
Loop Resistance: --------------------- 100Ω per zone (max.)
'HYLFH 6SHFLILFDWLRQV
Max # keypads:------------------------ 4, RPX-6 current = 65 mA
Max # of receivers: ------------------- 2, GEM-RECV-XP8
current = 65 mA each
Max # of compatible
2-wire smoke detectors:------------- 10
Max Keypad wire length:------------ 1000’ total wire length
0LVFHOODQHRXV
Housing Dimensions : -------------- 11" x 121/8" x 3"
(28 x 30.8 x 7.6) HxWxD
Maximum Charging Current: -------165 mA
Shipping Weight: -------------------- XP-600/4 15.5 lbs.
Maximum Input Current: -------------2.58 A
Operating Temperature: ------------ 0-49ºC (32-120°F)
3
Wi846c
page 3
Tuesday, September 16, 1997 10:36
WI846C XP-600 Installation Instructions
8/ &RPSDWLEOH 6PRNH 'HWHFWRUV
2UGHULQJ ,QIRUPDWLRQ
XP-600 Compatible Smoke Detectors
Mfg
Sentrol
System
Sensor
4-Wire
Smoke Detector
2-Wire
Smoke Detector
449AT
449C
449CRT
449CST
449CSRT
449CSRH
449CSST
449CLT
449CSLT
449CTE
741U
742U
712U
722U
732U
711U
721U
721UT
731U
1112
2112
2112T
2112TSRB
2100
2100T
1100
Smoke Detector
Base
701U
702U
702RE
702RU
/LVWLQJV DQG $SSURYDOV
UL HOUSEHOLD FIRE AND BURGLARY WARNING SYSTEM CONTROL UNIT
STANDARDS # 1023, 985
XP-600
RPX-6
ZDR
OI218
WI847C
2SWLRQDO $FFHVVRULHV
GEM-RECV-XP8:
GEM-TRANS2:
GEM-KEYF:
GEM-SMK:
GEM-PIR:
GEM-DT:
GEM-GB:
RB1000:
Veriphone:
PCD3000:
PCI2000/3000:
VERIFIED TO COMPLY WITH F.C.C. PART 15 AS CLASS B : DIGITAL DEVICE
(XURSHDQ (0& 5HJXODWLRQV &( &HUWLILFDWLRQ
6 zone Control Panel with 2-wire fire
Keypad
Zone Doubling Resistor (2.2K & 3.9K)
Operating Instructions XP-600
Programming Instructions XP-600
PCL2000A:
*Wireless Receiver
Window/Door Transmitter
Keyfob Transmitter
Wireless Smoke Detector
Wireless PIR
Wireless Dual-Technology Sensor
Wireless Glass-Break Detector
Relay Board
Audio Verification Module
Downloading Software for IBM PC Compatibles
Software with Interface for IBM PC Compatibles
(includes PCL2000A local download cable)
Local Download cable
*Supports up to 8 zones, 4 Key Fobs, 4 Smoke Detectors
HARMONIZED STANDARDS: EN50081-1 and EN50082-1
EC DIRECTIVES: 89/336/EEC, Electromagnetic Compatibility Directive
4
Wi846c
page 4
Tuesday, September 16, 1997 10:36
3URJUDPPLQJ WKH 3DQHO
Refer to XP-600 Programming Instructions (WI8547C)
Defaulting the Panel
1. Remove power from the panel.
2. Remove all wiring from terminal 15 (PGM)
and terminal 3.
3. Connect terminal 15 (PGM) to terminal 3.
4. Apply power to the XP-600 control panel.
5. After a few seconds the ARMED, READY and
SYSTEM TROUBLE LEDs will flash.
6. The keypad will beep 3 times indicating the
panel default values have been loaded.
7. Remove wiring between terminal 15 (PGM)
and terminal 3.
8. Re-install original wiring for terminal 15 (PGM)
and terminal 3.
*
ing PCD2000 Software running PCPreset. For
Site Initiated Downloaded, see Auto Download
ID Number [93].
Local Downloading
Wire as shown in Figure 1. Use the power up or
method of establishing a connection. The
power up method is recommended if the panel is
attempting to report.
+12
+PWR
-13
14
15
16
17
18
19
GND
GREEN
PGM
(-)
TIP
RING
TIP
RING
-13
14
15
16
17
18
19
GND
GREEN
PGM
(-)
TIP
RING
TIP
RING
TELCO
PHONE
GRY
TELCO
BRN
RJ31X
PHONE
XP-600 Panel at the site
RED
RED
GREEN
BLACK
TELCO
PCI2000
PCL2000A
MODEM
Keypad Programming
FIGURE 1 LOCAL DOWNLOAD
Refer to WI847C for information on keypad programming.
Remote Downloading
+PWR
GREEN
Any programming in Dealer Options 1 [96] and Dealer
Options 2 [97] will not be defaulted. If Dealer Code
Lockout has been programmed the panel will not default
the Dealer Code.
The XP-600 panel can be download/uploaded
with PCD3000 software using the Ring Method,
Answering Machine Override (Second Call) or
Method of downloading. The panel can
also be automatically downloaded/uploaded us-
+12
RED
NOTE:
Downloading
4. Site-Initiated (PCPreset &
)
5. Automatic Downloading (Using PCPreset)
Wire as shown in Figure 2. The panel can
be remotely download/uploaded using any
one of the following methods:
1. The
method
2. Call-in method
3. Answering Machine Override (Second
Call)
J1
J2
TO COMPUTER
TO EXTERNAL
MODEM
J3
LOCAL
TO
J4
TELCO
J5 LINE
OUT TO
MODEM
FIGURE 2 REMOTE DOWNLOAD
5
Wi846c
page 5
Tuesday, September 16, 1997 10:36
WI846C XP-600 Installation Instructions
,QVWDOODWLRQ
Mounting the Panel
Mount the Panel close to an unswitched AC
source, a cold-water pipe ground, and a telephone line connection.
Mounting the Keypad
A keypad should be located near an exit/entry
door. To remove the keypad from the backplate,
insert a small screwdriver into the square hole at
the bottom of the keypad. Pull up on the screwdriver to pop off the cover.
For increased protection, additional detectors
should be installed in areas other than those
required, such as the dining room, bedrooms
and utility room. Heat detectors, rather than
smoke detectors, are recommended in
kitchens, attics, and garages due to conditions
that may result in false alarms and improper
operation.
Refer to NFPA Standard 74 (National Fire Protection Association, Batterymarch Park,
Quincy, MA 02269) for additional information,
including proper mounting methods.
Grounding the Panel
Connect the control-panel EARTH GROUND
screw to a metal cold-water pipe. Do not use a
gas pipe, plastic pipe or AC ground connections.
Use at least #16 AWG wire. Connect a wire with
a ground lug crimped or soldered onto one end
and connect it to the EARTH GROUND screw in
the cabinet.
AC Power and Battery Wiring
Complete all wiring before connecting the battery
or AC Power. Do not plug the transformer into a
switched outlet.
Up to 4 keypads can be connected on individual
wire runs with #22 AWG wire with a maximum
total cable length of 1000 feet. Each keypad
draws approximately 65 mA.
Keypad Wire Color
:LULQJ
Telephone Wiring
Wire as shown in the wiring diagram in the back
of this manual.
Control Panel Terminal
RED
12 (+PWR)
WARNING
BLACK
13 (GND)
GREEN
14 (GREEN)
The FCC restricts the use of this equipment on
certain telephone lines. Read the FCC statement on the back of this manual to ensure
compliance.
TABLE 1 KEYPAD W IRING
Typical Fire Installation
(Where permitted by local codes)
Install smoke detectors outside each sleeping
area and on each floor, including the basement.
Install the living room and basement smoke detectors near the stairway of the next upper level.
FIGURE 3 Typical Fire Installation
6
Wi846c
page 6
Tuesday, September 16, 1997 10:36
Burglary Zone Wiring
NAPCO’s EZ Zone DoublingTM is simple. Each
terminal has 2 zones, use an E (2.2 K) type Zone
Doubling Resistor for the primary zone and a Z
(3.9 K) type Zone Doubling Resistor for the
secondary zone.
Terminals
Primary
Secondary
3&4
Zone 1
Zone 4
5&4
Zone 2
Zone 5
6&7
Zone 3
Zone 6
TABLE 2 EZ
Fire Zone Wiring
Keypad Sounder
Wire the Fire Zone as shown in the Wiring
Diagram in the back of this manual. An EOL
resistor must be installed, even if the Fire Zone
is not used.
3 QUICK BEEPS
Fire Zone Normal
13.0 V
Fire Trouble
13.8V
Fire
0.0 V
TABLE 4 VOLTAGE AT FIRE ZONE (Terminals 8&9)
PGM Wiring
ZONE DOUBLINGTM
Wire zones as shown in the wiring diagram at the
back of this manual (pg. 27). All resistors must
be installed, even if the zone is not used. If
required, unsupervised open circuit devices may
be used instead of closed circuit devices. Program the zone as an Open Circuit Zone [06]
(Zone Doubling Resistor required). If necessary,
use the voltage chart below to verify proper
voltages.
Primary and Secondary zones normal
1.9 V
Secondary open
2.5 V
Primary open
3.2 V
Primary and Secondary open
5.0 V
Primary and Secondary shorted (Sys. Trbl 7Zone Trbl)
0.0 V
The PGM is a switched negative output that is
activated depending on the programming option(s) that have been selected [08], [23] - [25].
Connect the device controlled by the PGM
between +PWR and the PGM terminal
(maximum load of 50 mA).
.H\SDG 2SHUDWLRQ
Keypad zone LEDs indicate zone status.
ARMED, READY and
SYSTEM LEDs provide system status. The keypad sounder provides feedback beeps for correct and incorrect
entries.
Panel Armed (System ON)
Chime ON
Fault Find Mode ON
Keypad Sounder ON
Zone Bypassed
6 QUICK BEEPS
Panel Disarmed (System OFF)
Chime OFF
Fault Find Mode OFF
Keypad Sounder OFF
Zone Un-Bypassed
1 SECOND - STEADY TONE
Incorrect Code Entered
Invalid key entry
4 LONG BEEPS (PRIORITY CONDITION)
1. Entering an Arm Code with a faulted zone
(Not an Auto-Bypass Reentry Zone).
2. Entering an Arm Code when the Bell or
PGM is ON (Bell and PGM will turn OFF).
3. Arming with the Fire LED ON - reset required. Press the
key.
TABLE 3 VOLTAGE AT TERMINALS 3&4, 5&4, 6&7
7
Wi846c
page 7
Tuesday, September 16, 1997 10:36
WI846C XP-600 Installation Instructions
Keypad LEDs
3DQHO 2SHUDWLRQ
ARMED LED DEFINITION
Armed
Instant Mode
Zone in Alarm
ON
Rapid Flash
Flashing
READY LED DEFINITION
Ready to be Armed
Zone faulted
ON
OFF
SYSTEM LED DEFINITION
AC Failure
System Trouble(s)
Flashing
ON
FIRE LED DEFINITION
Fire Alarm
Fire Memory/*Fire Trbl
*See Note 1
Flashing
ON
ON
OFF
ZONE LED DEFINITION
Faulted Zone
Bypassed Zone
Zone in Alarm
Before arming the system close all protected
zones (unless programmed as Auto-Bypass
Reentry Zones). Enter a 4-digit Arm/Disarm
code, the keypad will provide a feedback beep
for each key pressed. If a valid Arm/Disarm
code is entered, the keypad will beep 3 times.
If an incorrect Arm/Disarm code is entered, the
keypad will sound a 1-second tone indicating an
incorrect entry.
Arming without Entry Delay (Instant
Mode)
Enter the
to eliminate the entry delay.
The ARMED LED will flash rapidly to indicate
the panel is in Instant Mode. If an Exit/Entry
Zone is tripped while the panel is in Instant
Mode the panel will go into alarm immediately.
Arming/Disarming with a Keyswitch
The system can be armed/disarmed by using a
momentary Keyswitch wired to Zone 6. Program
Keyfob/Keyswitch Chirp [23-4] for an audible
indication of system arming and disarming.
NOTE:
Faulted Keyswitch or silent 24 hour zone normally do not
display at the keypad. If a silent 24 hour zone or Keyswitch
is faulted at the time of arming the faulted zone will display
only while the priority sound is ON.
Arming Instant with a Keyfob
AC LED DEFINITION
AC Present
AC Failure
Arming (System ON)
[81-84]. To arm the system with all zones protected press the
key. Press and hold the
or
key for 1.5s to fully set the system
(The LED on the Keyfob indicate the Keyfob has
transmitted the signal).
Program Keyfob/
Keyswitch Chirp [23-4] for an audible indication
of system arming and disarming.
ON
Slow Flash
Flashing
NOTE:
* If Fire Trouble on Fire LED [96-4] has been enabled, a steady
Fire LED will indicate Fire Trouble.
Arming/Disarming with a Keyfob
The system can be armed by pressing the
key, and disarmed by pressing the
key on
the Keyfob. Zones programmed as Exit/Entry
Follower Zones can be bypassed when the
or
keys on the Keyfob have been programmed for Interior [81-84]. Zones programmed as Home/Away with Delay Zones can
be armed regardless of the state of the Exit/
Entry Zones when the
or
keys on the
Keyfob have been programmed for Full Set
The panel can be ARMED INSTANT when the
or
keys on the Keyfob have been
programmed for Instant [81-84]. To arm the
system with Instant protection press the
key, then press and hold the
or
key for
1.5s to arm the panel with INSTANT protection.
Disarming (System OFF)
After entering the premises through an Exit/Entry
Zone, the keypad will sound the Entry Delay
Tone. Enter a valid Arm/Disarm code. If a valid
8
Wi846c
page 8
Tuesday, September 16, 1997 10:36
Arm/Disarm code is entered, the keypad will
beep 6 times, indicating the panel has been
disarmed. The red Armed LED will go out. If an
incorrect Arm/Disarm Code is entered, the keypad will sound a 1-second tone, indicating incorrect entry. Press the
key and re-enter the
code.
Disarming after an Alarm (Alarm Memory)
The armed LED and the zone(s) that caused the
alarm will be be flashing. Disarm the panel. The
system is currently not detecting zone faults or
displaying system trouble. The zone(s) that
caused the alarm will continue to flash. The
Ready and
SYSTEM TRBL LEDs are out
indicating:
Press the
Bypassing a zone
Exit/Entry Zone is not violated
Zones selected as Home/Away with Delay
Zones will be bypassed automatically.
Press the
key, then the zone number to be
bypassed. While the panel is DISARMED, the
bypassed zone LED will flash slowly; indicating
the zone has been bypassed. While the panel is
ARMED, the bypassed zones will only be displayed if the Display Bypassed [21-3] option has
been selected.
Away with Delay
Exit/Entry Zone is violated
Zones selected as Home/Away with Delay
Zones will have a fixed 20-second entry
delay when violated before an Exit/Entry
Zone.
Full Setting the System with Automatic
Bypassing - Home/Away with Delay
Zones
From the Keypad
The system is displaying Alarm Memory.
key to clear Alarm Memory.
%\SDVVLQJ
Press
to return protection to
Home/Away with Delay Zones that have
been automatically bypassed. Three minutes are allowed to walk through Exit/Entry
and Exit/Entry Follower Zones.
Using A Keyfob (GEM-KF)
Automatic Bypassing
Home/Away with Delay Zones
This zone type has the following operation depending on whether an Exit/Entry Zone has been
violated during the Exit Delay time.
Home
All zones in the system can be armed
regardless of the state of the Exit/Entry
Zone when arming with a Keyfob and using
an AUX key programmed as Full Set.
Press
and press and hold the
or
keys for 1.5s when leaving the
premises. All zones, including Home/Away
Zones are armed.
Unbypassing a zone (Disarmed only)
Press the
key then the number of the
zone to be unbypassed.
Group Bypass
Press
to Bypass all Exit/Entry Follower Zones [02] or Home/Away Zones [01]
(only if the system is programmed exclusively for Home/Away with Delay zones).
.
Using A Keyfob (GEM-KF)
Hold the
or
key on the Keyfob to
Bypass all Exit/Entry Follower Zones [02] or
Home/Away Zones [01] (only if the system is
programmed exclusively for Home/Away with
Delay zones).
8VHU 3URJUDP 0RGH
To prevent the loss of the User 1 Code, the panel
default program includes User 1 Code Lockout
[96-2].
To change the User 1 Code from its default value
9
Wi846c
page 9
Tuesday, September 16, 1997 10:36
WI846C XP-600 Installation Instructions
of 1234, program the 4-digit User 1 Code through
Dealer Programming [95]. User 1 Arm/Disarm
code is also used to program User Codes 2 - 6.
By default, the User 1 code cannot be reprogrammed by the user.
If it is necessary to change the User 1 code, it
can be changed through downloading or Dealer
keypad programming. From Dealer Program
Mode, change the User 1 Code Lockout ([96-2]
LED=OFF) to disabled.
Entering User Program Mode
1. Enter
2. Enter User 1 Code
(
)
(Default)
While in User Program Mode the Armed,
READY and JSYSTEM Trouble LEDs will continue to flash, follow the example below to
program User 2’s code to 1923.
User Mode Programming Example:
1. Press
, Zone 2 LED will Flash
2. Enter
, Zone 2 LED will
continue to flash until the 4th digit is entered. The keypad will beep 4 times confirming a valid entry (Zone LED steady).
Deleting a User Code
$50('
5($'<
6<67(0
),5(
$&
*
Press the number of the User to be deleted, the
zone LED will be flashing indicating that the
user has been selected. Press the
, the
LED associated with the user will now be OFF.
Exiting User Program Mode
To exit User Program Mode press the
Zone LED Meaning
OFF
User Arm/Disarm Code not programmed
Flashing
User Arm/Code is currently being programmed
Steady
User Arm/Disarm Code has been programmed
TABLE 5 ZONE LED DEFINITION-USER PROGRAM MODE
"
key.
;3 &RPPDQGV
User Commands
Bell Test
battery operation under load. The Alarm output
requires a battery in order to supply the specified
output. If the battery cannot sustain the load, a
low battery indication will be displayed. A battery
test is also performed on power-up after a 3
minute delay.
*A battery test occurs every 4 hours when
Household Fire [96-3] has been selected.
Group Bypass
Enter this command to bypass all Exit/Entry
Follower Zones or Home/Away Zones (only if the
system is programmed exclusively for Home/
Away with Delay zones).
Instant
Enter this command before or after arming to
remove the entry delay on Entry/Exit Zones. The
keypad ARMED LED will flicker rapidly. Faulting
a Exit/Entry Zone will result in an immediate
alarm.
Chime ON/OFF
Enter this command to turn chime ON/OFF. The
Keypad will chime on any zone that has not been
selected as an Exit/Entry Follower Zone, Home/
Away with Delay Zones, or 24 Hour Zone.
Enter this command to turn on the Bell, keypad
sounder and keypad LEDs for 2 seconds. The
battery is tested during a Bell Test, and automatically every *24 hours to ensure proper
10
Wi846c
page 10
Tuesday, September 16, 1997 10:36
+ User 1 Code - User Program
Mode
Keypad Sleep Mode ON/OFF
Enter this command to turn the keypad sounder
ON/OFF. When the keypad is in Sleep mode all
keypad sounds will be silenced except for keypad feedback beeps and Keypad Sounder on
Alarm.
User Commands - Optional
Easy Exit/Easy Arm
If enabled in Dealer programming, enter this
command while the panel is Armed to allow 3
minutes to exit the premises through Exit/Entry
and Exit/Entry Follower Zones. Enter
to
arm the panel.
To disarm the panel a valid
Arm/Disarm code must be entered. Requires
Easy Exit/Easy Arm [21-2] to be enabled.
!
Access on PGM
If enabled in Dealer programming, enter this
command to activate the PGM output (Terminal
15) for 5 seconds.
'HDOHU &RPPDQGV
Download (Programming Re-
quired)
Establish a connection between the PCD phone
line and the Control Panel phone line. When
ready, tell the installer to arm, then disarm.
Then enter
in order to establish a
connection. Phone connection to installer will
go "dead" as downloader and panel connect.
Fault Find ON/OFF
Hardwired Zone Operation
Enter this command to turn Fault Find ON/OFF.
While in Fault Find mode, the loop response for
all zones will be set to the faster response of 40
ms. The keypad will beep for .25-seconds when
hardwired zones are faulted and for 1-second
when zones are restored.
SIGNAL STRENGTH
.25S BEEP
4
5
6-7
BEEP
8-10
BEEP BEEP BEEP BEEP
BEEP BEEP
BEEP BEEP BEEP
TABLE 6 AUDIBLE SIGNAL STRENGTH INDICATION
=21( =21( =21( =21( =21( =21( =21( =21( =21( =21( =21( =21( =21( =21( =21( =21( 6-7
8-10
4
:LUHOHVV 2SHUDWLRQ
6LJQDO 6WUHQJWK
While in Fault Find mode the keypad will provide an audible (Table 6) and visual (Figure 5)
indication of each transmitter’s signal strength.
The signal strength metering is based on a
scale of 4 to 10, with 4 being marginal and 10
being excellent.
The keypad will beep out a number, from 1-4,
corresponding to the signal strength of the
transmitter. See Table 6. Each beep is 1second long. The keypad will sound a short
beep for transmitters with signal strengths of 3
or less.
KEYPAD SOUNDER
3 or less
5
FIGURE 5 VISUAL SIGNAL STRENGTH INDICATION
Signal Strength Logging Mode
The Signal Strength Logging Mode is a troubleshooting tool which allows the collection of
signal strength information for all transmitters on
the system. Normally the Signal Strength of Supervisory Signals are not logged; during Signal
Strength Logging Mode the signal strength information for all supervisory signals received over a
two hour period will be saved to the LOG.
Local Activation
Enable [92-4=ON], this will initiate a two hour test
period where all supervisory signals will log signal strength information.
11
Wi846c
page 11
Tuesday, September 16, 1997 10:36
WI846C XP-600 Installation Instructions
Remote Activation
Using NAPCO’s Quickloader Software
(Version 3.26 or higher), follow the instructions below:
From the Status Screen
Press F6
Select Miscellaneous Control
Select Enable Signal Strength Logging
Uploading Signal Strength Information
from the Log
After approximately (2) two hours, reestablish a connection with the panel. Signal strength log information ranges from 1
to 10. The logging of signal strength should
appear similar to the sample LOG below:
07/24/97 17:44
07/24/97 17:42
07/24/97 15:23
07/24/97 15:13
07/24/97 15:13
07/24/97 14:27
07/24/97 14:25
07/24/97 14:25
07/24/97 14:25
07/24/97 14:24
07/24/97 14:24
07/24/97 13:13
QL: Full Program Uploaded
QL: Technical Connection
(callback) Technician 2
Transmitter Status: GEM_SMK
1(7A0DB5): SS=7
Transmitter Status: GEM_SMK
2(768447): SS=8
Transmitter Status: Zone 2,
SS=6
Trouble: RF Link,
GEM_RECV 1
Panic: Keypad
Panic: Keyfob 1(933780)
SS=8
Dealer Program Mode Entered
Instant: Keyfob 1(933780)
SS=8
QL: Connection Terminated
(10 MIN T/O)
QL: Full Program Downloaded
=RQH )HDWXUHV
from a Keyfob. Program the Keyfob AUX
1 or AUX 2 button for Full Set [81-7].
[00]Exit/Entry Zones
NOTE:
If
is Entered during Exit Time, Home/Away with
Delay Zones will be automatically bypassed, even if the
Exit/Entry Zone is violated. Easy Exit/Easy Arm [22-2] must
be enabled.
Delay allows exit and entry through an Exit/
Entry Zone after the system is armed
without setting off an immediate alarm.
Exit Delay allows the user to leave the
premises after arming. Entry Delay allows
the user time to enter and disarm. The
entry delay may be canceled by pressing
.
!
[01]Home/Away with Delay Zones
Zones that automatically bypass at the expiration of the exit delay if the EXIT/ENTRY
zone(s) are not violated. Zones of this type
have a three (3) minute power-up delay,
and do not display or cause an alarm if
faulted when the system powers up.
Pressing the
key cancels the 3 minute
timer.
"
If Exit/Entry zone(s) are violated during the
exit delay, zones programmed as Home/
Away with Delay Zone(s) will have a fixed
20-second entry delay, if violated before the
Exit/Entry zone.
To eliminate this fixed 20-second entry delay, also program zones as Exit/Entry Follower Zones [02].
To return protection to zones of this type,
press
from the keypad or
or
#"
[02]Exit/Entry Follower Zones
Entry Delay allows the user time to enter and
disarm. Allows exit after the panel is armed
without setting off an immediate alarm and
allows entry only if an Exit/Entry Zone [00]
has been violated first. Zones of this type
have a three (3) minute power-up delay, and
do not display or cause an alarm if faulted
when the system powers up. Pressing the
key cancels the 3 minute timer.
"
##
Group Bypassing - Zones programmed as
Exit/Entry Follower Zones will be Group bypassed if the
is pressed while
disarmed or within the Exit Delay.
Auto Interior Bypassing - Also program
zones as Home/Away with Delay Zone(s)
[01] to automatically bypass at the expiration
of the exit delay if the EXIT/ENTRY Zone(s)
are not violated during the exit delay.
[03]Auto-Bypass Reentry Zones
Zones programmed as this zone type are
permitted to be faulted at the time of arming.
Once the zone is restored, while the control
panel is still armed, the zone will automati-
12
Wi846c
page 12
Tuesday, September 16, 1997 10:36
cally be unbypassed and any subsequent
violations of the zone will cause an alarm
condition.
[04]24-Hour Protection
A zone that provides protection at all times,
whether or not the system is armed.
[05]40 ms Loop Response
Normally loop response is 750 ms, select
this option to change the loop response to 40
ms. The slower the loop response, the less
sensitive the system will be to intermittents
(swingers). The programming option is not
permitted for UL installations.
Enables the Bell Output on a zone trip for each
zone selected. The Bell Output will remain ON
for the length of time programmed for Burg
(Steady) Output [07] or it will remain ON until
turned off by entering a valid Arm/Disarm
Code; 0 means output will stay ON until reset.
[08]PGM Output
Enables the PGM Output on a zone trip for
each zone selected. The PGM Output will remain ON until reset.
[11]Entry Delay
Delay time permits entry through Exit/Entry
Zone(s) after the system is armed without
setting off an immediate alarm. Entry Delay
allows the user time to enter and disarm the
system. Upon entering, the keypad sounder
will sound a steady tone (Entry Sound) to
remind the user to disarm the system. Entry
Delay Time [11] may be programmed for up
to 255 seconds (4¼ minutes); a value of 0
defaults to 30 seconds. Entry Delay may be
before or after
canceled by pressing
arming.
!
[09]Selective Bypass
[06]Open Circuit Zones
Program this zone type if unsupervised normally open circuit devices are required The
programming option is not permitted for UL
installations.
Enables the ability of the User to bypass
zones. By default, all zones are permitted
to be bypassed.
Can be programmed from 1 to 255 min (4¼
hours); 0 means output will stay ON until
turned off by entering an Arm/Disarm Code.
[13]Fire (Pulsed) Output Time-out
[10]Exit Delay
.
Wire the normally
open contact
as shown (Zone 4).
[12]Burg (Steady) Output Time-out
6\VWHP 7LPHV
Normally Open Zone Wiring
(Z)
TM
ZONE 4
.
EZ Zone Doubling
resistor
is required.
Program the
zone for
Open Circuit [06].
[07]Burg (Steady) Output
(E)
ZONE 1
The delay time which permits exit through an
Exit/Entry Zone [00] after the system is armed,
allows a user to leave the premises without
setting off an immediate alarm. Exit Delay
may be programmed for up to 255 seconds
(4¼ minutes); a value of 0 defaults to 60 seconds.
Can be programmed from 1 to 255 min (4¼
hours); 0 means output will stay ON until
turned off by entering an Arm/Disarm Code.
[14]Test Timer Interval
Program the interval, in days, between Test
Timer reports. Test Timer Interval may be
programmed from 1 to 255 days.
FIGURE 6 OPEN CIRCUIT W IRIING
13
Wi846c
page 13
Tuesday, September 16, 1997 10:36
WI846C XP-600 Installation Instructions
[15]Line Cut Time-to-Fail
Enable this feature by programming the delay time required to declare a line cut failure.
Programming 000 will disable line cut detection.
[16]Wireless Supervisory Timer
A transmitter will send a transmission every
time it is tripped; when there is no activity,
the transmitter sends a supervisory transmission about once an hour. If the receiver does
not receive any signal (either a trip or a
status) from a transmitter in the time specified, a system trouble ‘RF Supervisory Failure' will be indicated at the keypad. Timer is
programmable from 1-26 hours; 0 means NO
supervision.
[18]Test Timer Offset
Enter the time, in hours, that a Test Timer
will be reported after Dealer Mode has been
exited. With the default value of 12, the
test timer will be sent 12 hours after exiting
Dealer Mode. The test timer can also be
offset using NAPCO PCD3000 Downloading Software. On power up the test timer is
sent immediately. Follow the commands
below to offset the test timer using Quickloader Software:
From the Status Screen
Press F6
Select Miscellaneous Control
Select Test Timer Offset
Enter
New Test Timer Offset: 12 hours
Enter
to advance the test timer due
in time by 12 hours.
X
[17]Wireless Smoke Supervisory Timer
A smoke detector will send a transmission
every time it is tripped; when there is NO
activity, the smoke detector sends a supervisory transmission about once an hour. If the
receiver does not receive a signal (either a
trip or a status) from a transmitter in the time
specified, a system trouble ‘RF Supervisory
Failure' will be indicated at the keypad. The
Supervisory timer is programmable from 1-8
hours; 0 means NO supervision.
6\VWHP )HDWXUHV
[20]Keypad Features 1
%%
&&
'
)
(1) Enable Keypad Fire (
Additional Programming required:
Select reporting to Telco 1 [36-1] or Telco 3
[56-1].
(2) Enable Keypad AUX (
)
Additional Programming required:
Select reporting to Telco 1 [36-2] or Telco 3
[56-2].
(3) Enable Keypad Panic (
)
Additional Programming required:
Select reporting to Telco 1 [36-3] or Telco 3
[56-3].
(4) Enable Ambush - If enabled, the 6th
User Code will send an Ambush report when
entered to disarm the system.
Additional Programming required:
Program User 6 Arm/Disarm Code.
Select reporting to Telco 1 [36-2] or Telco 3
[56-2].
UL Installations: If Keypad Fire [20-1] is
enabled, the keypad must be mounted within
(3) three feet from the Control Panel.
[21]Keypad Features 2
(1) Audible Panic - Keypad Panic will not
turn the Bell on unless this option is programmed.
(2) Exit/Entry with Urgency - select to give
an audible indication of Exit and Entry times.
During the last 10 seconds of entry and exit
time, the keypad sounds a distinct sound to
indicate the premises must be left or the
panel must be disarmed.
(3) Display Bypassed (Armed) - Select to
display bypassed zones while the panel is
armed.
(4) Disable Code Entry Beeps - Program to
disable keypad beeping on valid code and
function entries.
14
Wi846c
page 14
Tuesday, September 16, 1997 10:36
[22]Miscellaneous Features 1
(1) Abort Delay - Program to allow a 15
second Delay (except 24 Hour Zones) after
a zone trip before reporting. Disarm the
system within 15 seconds to prevent reporting.
(2) Easy Exit/Easy Arm - Enables
command. While the system is armed, entering this command allows 3 minutes to Exit
through Exit/Entry and Exit/Entry Follower
Zones. Enabling this option also enables
Easy Arm, enter
to arm the system.
(3) Swinger Shutdown - Automatically disables armed zones with excessive alarm/
restores (swingers). Non-24-Hour Protection
zones: allows only 3 alarms and 2 restores
per zone per arming before the zone is disabled.
(4) Bell on Line Cut (Armed) - Program to
turn the Bell Output on if the telephone line
has been cut while the panel is armed.
!
[23]Programmable Output Features 1
(1) Audio Verification - Program to activate
the PGM during reporting. Select specific
zones for audio verification by programming
the required zones in PGM Output [08],
PGM Features 2 [24] and PGM Features 3
[25]. Connect the PGM to the VeriphoneTM
trigger low input.
(2) Access Output - Activates the PGM
output for 5 seconds using the
command.
(3) Follow Keypad Sounder - The following keypad sounds will activate the PGM
output: Entry Sounder, Keypad Pulsing
Sounder, Keypad Output on Alarm, Chime,
Fault Find.
(4) Keyfob/Keyswitch Chirp - Program to
chirp the PGM Output (1) one time when
the panel is armed or (2) two times when
the panel is disarmed. Wire as shown in
Figure 7.
PGM
BLK
+AUX
RED
K1
COM
+AUX
N/C
[25]Programmable Output Features 3
(1) AC Fail - Program to activate the PGM on
the loss of AC. (15 minute delay)
(2) Low Battery - Program to activate the
PGM on a Low Battery condition.
(3) *Trouble - Program to activate the PGM
on a Trouble condition.
(4) Armed - Program to activate the PGM
when the panel is Armed. The PGM output
will flash when the panel has gone into
alarm.
*Includes Bell Cut, Fire Trouble, Receiver
Fail-to-Respond, Receiver Tamper, Receiver
JAM, Wireless Smoke Low Battery, Wireless
Smoke Supervisory Fail.
N/O
Siren Driver
Steady Input
FIGURE 7 KEYFOB/KEYSWITCH CHIRP
[24]Programmable Output Features 2
(1) Fire - Program to activate the PGM on a
Fire alarm.
(2) AUX - Program to activate the PGM on
a AUX alarm.
(3) Panic - Program to activate the PGM on
a Panic alarm.
(4) Test Timer - Program to activate the
PGM during a Test Timer report.
[26]Miscellaneous Features 2
(1) Momentary Keyswitch Arming - Typically, connect a normally-open Keyswitch
across the zone AND its 3.3K zone-doubling
resistor.
(2) Reserved.
(3) Inhibit Fail-to-Communicate Display This option prevents the keypad from either
indicating or sounding when a Fail to Communicate has occurred.
(4) Inhibit Low Battery Display - Program
to inhibit the Low Battery Display at the
keypad. Low Battery Reporting is not inhibited. The programming option is not permitted for UL installations.
15
Wi846c
page 15
Tuesday, September 16, 1997 10:36
WI846C XP-600 Installation Instructions
7HOHSKRQH 1XPEHU 3URJUDPPLQJ
[30]Subscriber ID Number
)
For 4/2 format enter a 4 digit number. If 3/1
format is required, enter a 3 digit number,
then press the
key to blank the last digit.
[31]Telephone Number 1
Program the phone number to be dialed for
Telephone Number 1. Program the number
directly, just as it is entered on a TouchTone
phone. A fixed Dial Tone Detection (E) is
included prior to the Dialing Prefix (Block
Number 44). Programming an E is not required for Telco 1, Telco 2 and Telco 3. If
dial tone detection is not desired select No
Dial Tone Detection in Communicator Features [46-1].s Use the
key to blank out
remaining digits in the phone number.
)
[32]Receiver Format
Select the receiver format to be used to
report for Telephone Number 1: Program a
0 to disable reporting to Telco 1.
[0] Disabled
[1] Ademco Slow
[2] Radionics Slow
[3] Silent Knight Fast
[4] Universal High Speed
[5] Reserved
[6] Point ID
[7] Pager
[33]Receiver Options
(1) 2300 Hz HS/Kissoff - Select 2300 Hz
Handshake and Kissoff.
(2) Sumcheck - Only used for the following
Receiver Formats: Ademco Slow, Radionics Fast, Silent Knight Fast and Universal
High Speed. This is a sophisticated data
format used to enhance the speed and
check the accuracy of the received transmission. This format should be used whenever the central station has this capability.
Instead of sending a second round to verify
correct data, the panel sends a Sumcheck
digit after sending the Subscriber ID and
Alarm Code.(3) Single Digit - 3/1 Format.
3-digit Subscriber ID number and a 1-digit
Alarm Code will be transmitted.
(4) No Handshake - (All receiver formats
except Pager Format)
If programmed no Handshake/Kissoff is required by the panel.
[34]Zone Report, Telco 1
Select zone(s) required to send an alarm
report to Telephone Number 1.
[35]Zone Restore Report, Telco 1
Select zone(s) required to send a restore
report to Telephone Number 1. The zones
will send a restore after Bell time-out, unless programmed as silent zones.
[36]System Reporting, Telco 1
%%
&&
(1) Keypad Fire - Program to activate a
).
Keypad Fire report (
(2) AUX/AMBUSH - Program to activate an
).
AUX or AMBUSH report (
(3) Panic - Program to activate a Panic
).
report (
(4) Test Timer - Program to activate a Test
Timer report.
'
[37]System Reporting, Telco 1
(1) AC Fail Report - Program to activate an
AC Fail report (15 minute fixed report delay).
(2) Low Battery Report - Program to activate a Low Battery report.
(3) *Trouble Report - Program to activate a
Trouble report.
(4) Fire Report - Program to activate a Fire
report.
*Includes Bell Cut, Fire Trouble, Receiver
Fail-to-Respond, Receiver Tamper, Receiver
JAM, Wireless Smoke Low Battery, Wireless
Smoke Supervisory Fail. Point ID format will
report trouble(s) by device and ID number.
[38]System Restore Report, Telco 1
(1) AC Restore - Program to activate an AC
Restore report.
16
Wi846c
page 16
Tuesday, September 16, 1997 10:36
(2) Battery Restore - Program to activate a
Battery Restore report.
(3) Trouble Restore - Program to activate a
Trouble Restore report.
(4) Fire Restore - Program to activate a Fire
Restore report.
[39]Opening/Closing Report, Telco 1
Select users required to send opening and
closing reports to Telephone Number 1.
Do not program for users that are intended
to send an Opening After Alarm (Cancel
Code) or Conditional Closing reports.
[42]Receiver Format (Telco 2)
Select the format that will be used to report
for Telco 2 (Backup reporting). Refer to
section [32].
[43]Receiver Options (Telco 2)
Refer to section [33] Receiver Options.
[44]Dialing Prefix
Dialing prefix for Telco 1, Telco 2, and
Telco 3. Program if using an Outside
access number.
[45]Communicator Features 1
%DFNXS 7HOHSKRQH 3URJUDPPLQJ
[40]Subscriber ID Number (Telco 2)
For 4/2 format enter a 4 digit number. If 3/1
format is required enter a 3 digit number then
key.
press the
)
[41]Telephone Number 2
Program the phone number to be dialed for
Telephone Number 2. A fixed dial tone detection (E) is included prior to the Dialing
Prefix [44]. Dial tone detection can be disabled by programming No Dial Tone Detection [46-1]. To program any additional delay
enter a "D" where required in the phone
number.
(1) Communicator Enabled - Program to
enable the communicator.
(2) DTMF with Rotary Backup - The first
attempt to communicate is dialed using the
TouchTone method of dialing, subsequent
attempts are dialed using the pulse method
of dialing. Disable this feature to dial using
only rotary dialing.
(3) DTMF only - All attempts to communicate dial using the TouchTone method of
dialing.
(4) Backup Reporting to Telco 2 - After 2
attempts are made to communicate to
Telco 1 the backup phone number is dialed
(Telco 2).
[46]Communicator Features 2
(1) No Dial Tone Detection - Program to
disable dial tone detection for Telco 1, Telco
2 and Telco 3.
(2) 2:1 Rotary Dialing - Changes the make
break ratio when rotary dialing from 1.5:1 to
2:1.
(3) Backup if < 4 attemps - If Backup
Reporting [45-4] has been enabled, the
communicator will use Telephone Number 2 [41] for the remaining retries when
there are less than 4 retries remaining.
(4) Reserved
3DJHU 3URJUDPPLQJ
If Pager Format ([32]and/or[42]and/or[52] =
7) is selected, pager data will be displayed
as shown in Figure 8. If Pager Format is
selected 4/2 format must be programmed
and Sumcheck is not permitted. If a PIN
number is required refer to Leading Digits
[47].
Leading Digits
Report Code
Subscriber ID Number
FIGURE 8 DEFAULT PAGER DISPLAY
17
Wi846c
page 17
Tuesday, September 16, 1997 10:36
WI846C XP-600 Installation Instructions
Pager Alarm data is the same as 4/2 format
with the exception that the 2 digit Report
Code is transmitted before the 4 digit Subscriber ID.
NOTE:
Digits in Report Codes and subscriber IDs that are programmed with "B" through "F" will be converted to "0"s.
[47]Leading Digits
Pager PIN Number - If a PIN number is
required by the paging system, program the
PIN number in the Leading Digits location.
See sample program below.
If a 7-digit PIN number is required, program
the panel as follows:
[31]/[41]/[51] - Pager Telephone number
[32]/[42]/[52] - Select Pager Format
[47] - X X X X X X X C
7-digit PIN Number
Terminating Digit (#)
Leading and Trailing digits can be letters B,
C or D. B = the * button on a telephone, C =
the # button on a telephone, D = 2 second
delay.
[48]Trailing Digits
Transmitted after alarm data. Refer to section [47] for programming information.
[49]Pager Options
(1) Skip Alarm Data - Once pager format is
selected, program this option to skip alarm
data. If this option is selected, all the
programmed Leading and Trailing digits are
sent, but the event code and subscriber ID
are not transmitted. With this option selected, a telephone number programmed
in Leading Digits or Trailing Digits would
send the telephone number to the pager
each time a report is sent.
(2) Reserved
(3) Reserved
(4) Reserved
7HOHSKRQH 1XPEHU 3URJUDPPLQJ
[50] - [59]
Programming is the same as for Telco 1.
Program to split/double report to Telco 3.
Refer to sections [30] through [39].
5HSRUW &RGHV
[60]Zone Report Codes
Report Code for Zones 1 through 6.
4/2 format - The Zone Report Code is the
1st digit of the report code sent, the second digit is the zone number of the reporting zone. For example, if zone 2 has a
report code of 3, the report code would be
32.
3/1 format - Sends only the report Code and
does not append it with the zone number.
[61]Point ID Report Codes
Point ID Report Codes are defaulted to Burglary for zones 1 through 8. Optionally, Point
ID codes for zones 1 through 8 can be
programmed as follows:
[1] Fire
[2] Panic
[3] Burglary
[4] Holdup
[5] General Alarm
[6] Reserved
[7] Gas Alarm
[8] Heat Alarm
[9] Reserved
[A] Auxiliary
[B] 24 Hour
[62]Zone Codes
[62-1] Restore code - Zones 1 through 8.
The second digit of the restore code is the
zone number of the restored zone. For
example, if the Zone Restore Code [62] is
programmed to E, the restore code for that
zone would be E4 (4/2 format).
[62-2] Trouble Code - Conditional Closing Reports. Zones that are bypassed at
the time of arming send this code along
with the zone number of the bypassed
zone(s). For example a conditional closing
by User 2, with zones 2 and 3 bypassed
would be as follows: 1234 C2
F2
F3
18
Wi846c
page 18
Tuesday, September 16, 1997 10:36
[63]System Report Codes
Program a 2-digit report code for Keypad
Fire, Keypad AUX, Keypad Panic, Test
Timer, AC Fail, Low Battery, Trouble and
Fire.
[64]System Restore Code
The code sent when a system condition
restores. The second digit of the 2-digit
restore code is the second digit of the System Report Code [63]. For example, if a Low
Battery System Report Code is F8 the Battery Restore would be E8 (4/2 format).
[65]Opening and Closing Codes
Program Opening and Closing Codes for
Users 1 through 6. The second digit of the
report code is the number of the user that
armed or disarmed the system. For example, if the Closing Code [65] is programmed
with a C, the closing code for User 2 would
be C2 (4/2 format).
[66]Ambush Report Code
Program a 2-digit report code for Ambush.
To send an ambush report, program a User
Code for User 6, Program report User 6 as
Ambush [20-4] and Select reporting for Telco
1 [36-2] and/or Telco 3 [56-2].
(QKDQFHG &RPPXQLFDWRU )HDWXUHV
[67]Telephone Number 1
(1) Opening After Alarm (Cancel Code) When enabled, all users that are not selected to report on Opening/Closing [39] will
report an Opening only when opening after
an alarm has occurred.
(2) Conditional Closing Telephone 1 When enabled, all users that are not selected to report an Opening/Closing ([39],
[59]) will report a Closing only when zones
have been bypassed. The Zone Trouble
Code [62-2] is used to report zones that
have been bypassed at the time of the
closing report.
(3) Reserved
(4) Reserved
[68]Telephone Number 3
(1) Opening after Alarm (Cancel Code) see [67-1].
(2) Conditional Closing Telco 3 - see
[67-1].
(3) Reserved
(4) Reserved
:LUHOHVV
Up to two receivers can be wired to the
XP-600. Each wireless transmitter can be
mapped to a zone. Only 1 wireless device is
permitted per zone, however, the use of both
hardwired and wireless on a zone is permitted.
To Map a transmitter to a zone:
1. Enter the Programming Block Number
that the transmitter is to be mapped to.
2. Enter the 7-digit RF ID number directly,
just as it is shown on the device label.
After the 7th digit is entered the keypad
will beep.
A transmitter will send a transmission every
time it is tripped. The transmitter also sends
a supervisory transmission about once every
hour. If the receiver does not receive a
signal from a transmitter in the time programmed in Wireless Supervisory Timer, a
system trouble ’RF Supervisory Failure' will
be indicated at the keypad.
Program Wireless Supervisory Timer [16] to
change the supervisory time from the default
of 12 hours.
The Signal strength of a transmitter can be
Fault
checked at the keypad (see
19
Wi846c
page 19
Tuesday, September 16, 1997 10:36
WI846C XP-600 Installation Instructions
Find Mode) or saved to the LOG (see Signal
Strength Logging Mode - pg. 11).
[71-76] Wireless Transmitters
Enter the RF ID# and the point number that
is to be mapped to the zone.
Programming Example
Map point 1 of a window door transmitter with
an RF ID# of 0012B0:0 to Zone 3.
1. Enter Dealer Mode.
(beeps)
2. Enter
3. Enter
4. Enter
(beeps)
(beeps)
Note: If the RF ID# in step 3 is not entered
correctly the keypad will emit a 1 second
tone indicating incorrect entry. Repeat steps
2 - 4 above.
[81] - [84] Wireless Keyfobs
The GEM-KF is a hand held wireless transmitter capable of Arming and Disarming the
control panel and/or activating 2 Auxiliary
Functions. To activate the auxiliary funcor
key for
tions, press and hold the
1.5 seconds (see WI752 for more information).
Enter the RF ID# and AUX 1 and AUX 2
options for each Keyfob.
AUX 1 & AUX 2
Programming Options:
1 Panic
Program a 1 in the AUX 1 and/or AUX 2
option to initiate a panic alarm when the
or
buttons on the Keyfob are
pressed.
Additional programming required:
) [20-3]
Keypad Panic (
Panic Report to Telco 1[36-2] and/or Telco
3 [56-3].
Audible Panic (Optional) [21-1]
2 AUX
Program a 2 in the AUX 1 and/or AUX 2
option to initiate a AUX alarm when the
or
buttons on the Keyfob are pressed.
Additional programming required:
) [20-2]
Keypad AUX (
AUX Report to Telco 1[36-2] and/or Telco 3
[56-2].
3 Bell ON
Program a 3 in the AUX 1 and/or AUX 2
or
option to turn the Bell ON when the
buttons on the Keyfob are pressed.
Press the
button to turn the Bell OFF.
4 PGM
Program a 4 in the AUX 1 and/or AUX 2
option to activate the PGM Output when the
or
buttons on the Keyfob are
pressed. Press the
PGM Output OFF.
button to turn the
5 Instant
Program a 5 in the AUX 1 and/or AUX 2
option to activate Instant Mode when the
or
buttons on the Keyfob are
pressed.
6 Access on PGM
Program a 6 in the AUX 1 and/or AUX 2
option to activate the PGM Output for 5
or
buttons on the
seconds when the
Keyfob are pressed.
Addition programming required:
Enable Access Output [23-2]
7 Full Set System
Program a 7 in the AUX 1 and/or AUX 2
option to Fully Set the System when the
and the
or
buttons on the Keyfob
are pressed, or when the
or
buttons
20
Wi846c
page 20
Tuesday, September 16, 1997 10:36
are pressed when the system is armed with
Exit/Entry Follower Zones or Home/Away
with Delay Zones that have been bypassed.
8 Interior
Program an 8 in the AUX 1 and/or AUX 2
option to Bypass Exit/Entry Follower Zones
or Home/Away with Delay Zones when the
or
buttons on the Keyfob are
pressed (only if the system is programmed
exclusively for Home/Away with Delay
Zones).
[85] - [88] Wireless Smoke Detectors
Enter the RF ID# of the smoke detector.
A wireless smoke detector sends a supervisory transmission about once every hour. If
the receiver does not receive a signal from a
transmitter in the time programmed in Wireless Smoke Supervisory Timer, a system
trouble ‘RF Smoke Supervisory Failure' will
be indicated on the keypad.
Program Wireless Smoke Supervisory Timer
[17] to change the time from the default time
of 8 hours. Refer to Household Fire [96-3].
Note: Mark Smoke Detectors (Smoke 1
through Smoke 4) in order to identify them in
the event of a supervisory or battery failure.
If Household Fire [96-4] is selected, Wireless
Smoke Supervisory Time is fixed at 4 hours.
'RZQORDGLQJ
[90]Callback Telephone Number
Program the phone number of the downloading computer to be dialed by the panel
during a high security download.
[91]Ring Count
Program the number of rings before the
panel will pickup. Ring Method [92-1]
(Downloading Features) must also be selected.
[92]Downloading Features
(1) Ring Method - Enable the ring method
of downloading. The panel will pick-up on
the number of rings programmed in Ring
Count [91].
(2) Answering Machine Override - Using
the downloading computer, call the panel.
When the operator has determined that the
panel has received 1-2 rings, pressing the
key will cause the downloading computer to immediately re-dial the panel. The
panel will pick-up on the first ring.
(3) Command 6 Download - Select to
method of downloading
enable the
(pg. 8).
(4) Signal Strength Test Mode - Program
X
to initiate a 2 hour test period. The signal
strength information for all supervisory signals received over a two hour period will be
saved to the LOG.
[93]Auto Download ID Number
Enter the Number that is used by PCPreset
when downloading using Site Initiated Auto
).
Downloading (
The requirements for Site Initiated Auto
Downloading are as follows:
1. Download Computer running PCPreset.
2. Program the telephone number of the
Download Computer in location [90] Callback Telephone Number.
3. Program location [93] with the number of
the PCPreset account that is to be downloaded.
PCPreset
1. Create the XP-600 account to be downloaded using PCD3000 Quickloader
Software.
2. Create a List using PCPreset.
.
3. Select the account by pressing
Select the desired account from the list
of PCD3000 accounts available. (The
location in the list is the Auto Download
ID Number [93])
4. Tag the list by entering
(download)
WW
D'
21
Wi846c
page 21
Tuesday, September 16, 1997 10:36
WI846C XP-600 Installation Instructions
5. Enter Standby Mode by entering
R
.
The Computer is now in STANDBY
Site
At the site perform the following three steps:
1. Arm the panel.
2. Disarm the panel.
The panel will now call the
3. Enter
download computer running PCPreset.
PCPreset will answer the call, establish
a connection, and then download the
account that matches the Auto Download ID Number [93] with the account of
the same number in the list that PCPreset is currently running.
'HDOHU 3URJUDPPLQJ
[94]Dealer Code
The default Dealer Code is 4567. Program
a new 4-digit Dealer Code. When the panel
is defaulted the Dealer Code will be changed
back to the default Dealer Code of 4567
only if Dealer Code Lockout [96-1] has not
been programmed.
[95]User 1 Code
The 1st User code is a program code as
well as an Arm/Disarm code. The default
User Code is 1234. If User 1 Code Lockout is programmed the User 1 Code cannot
be programmed from User Program Mode.
[96]Dealer Options 1
(1) Dealer Code Lockout - Program to
prevent the Dealer Code from changing
with a panel default.
(2) User 1 Code Lockout - If programmed
the User 1 Code cannot be programmed
from User Program Mode.
(3) Household Fire - Activates the following UL required features:
There is a 4 hour re-sound of wireless
Smoke Low Battery and wireless Smoke
Supervisory system troubles.
• An active System Battery test performed every 4 hours instead of 24
hours and Wireless Smoke Supervisory
Timer is set to 4 hours.
• Fire Bell Timing is March Time.
• Wireless Smoke Supervisory Time is
fixed at 4 hours.
(4) Fire Trouble on Fire LED - Normally
SYSall troubles are displayed on the
TEM TROUBLE LED, including Fire Trouble. If required Fire Trouble can be dis-
*
played on the Fire LED. Fire Trouble is
indicated by a steady Fire LED.
[97]Dealer Options 2
(1) International Dialing Protocol - No dialing if no dial tone, 60 s between attempts
and 4 s wait for dial tone.
(2) Invert Bell Output - Inverts the Bell
polarity and removes supervision from the
bell circuit.
(3) System Trouble Auto Restore - Normally, System troubles require acknowledgment (View System Trouble) in order to restore. If this option is selected troubles will
restore without requiring acknowledgment.
(4) User 1 Code-Program only - If enabled
User 1 Code will function only as the User
Program Code and will not Arm/Disarm the
panel.
Note: All programming within Programming
Blocks [96] & [97] will not change if the panel
is defaulted.
[98] Number of Re-Dials
The Number of re-dial attempts made by the
panel
before
indicating
a
Fail-toCommunicate.
22
Wi846c
page 22
Tuesday, September 16, 1997 10:36
6\VWHP 7URXEOHV
EXAMPLE
Use the System Trouble chart on the following
page to determine the specific System Trouble(s).
Press the
*
During normal panel operation the
SYSTEM
TROUBLE LED has the following two modes of
operation:
STEADY
FLASHING
1-7 possible trouble
groups, AC is present
1-7 possible trouble
groups, AC is not present
9LHZLQJ 6\VWHP 7URXEOHV
*
Press the SYSTEM on the keypad.
To determine the System Trouble Group Number, count the number of times the
SYSTEM
LED blinks. The keypad sounder will beep at the
same rate that the
SYSTEM LED blinks.
To determine the System Trouble, note the zone
LED that is ON. Look up the specific system
trouble on the chart on the following page.
The SYSTEM LED and keypad sounder will
continue to flash and beep. To view the next
System Trouble, if any, press the
key. Continue pressing the
key, if there are no more
system troubles to view, the system will return to
normal operation.
)
- LOW BATTERY SYSTEM TROUBLE DISPLAY
to enter System Trouble mode and
determine the specific trouble. Press any key to view
all system troubles.
Flashing
(System
Trouble
Group
Number)
Beeping
(System
Trouble
Group
Number)
System Trouble
Group #
Keypad SYSTEM Trouble LED is flashing 1
time indicating System
Trouble Group 1.
Keypad Sounder beeps
1 time indicating System
Trouble Group 1.
*
$50(
5($'<
6<67(0
),5(
$&
=21( =21( =21( =21( =21( =21( 1$3&2
Zone LED(s) is ON
indicates
(Specific Trouble)
Specific Trouble
Zone 2 LED is ON indicating
Low Battery. (1 Beep, LED 2)
FIGURE 9 SYSTEM TROUBLE EXAMPLE
Note: System Troubles Groups 3 through 7 System Trouble Groups that have a zone or
smoke detector associated with the trouble,
such as RF low battery. The zone(s) of the
device with a low battery will be displayed by
the ZONE LED. For example, a wireless low
battery on zone 2 would beep the keypad
sounder 3 times and turn on zone 2 LED.
Audible System Trouble Indication - For all
system troubles, except when the only system
trouble is the loss of AC, the keypad will beep
once every 10 seconds. The keypad will continue
to beep until the reset button is pressed or the
trouble has been acknowledged by pressing the
key.
)
System Trouble Reporting
The following system troubles, when enabled to
report to Telco 1 [37-3] or Telco 3 [57-3], will send
the report code programmed in Trouble Report
[63] if reporting using a pulse format:
System Trouble
Pulse Report Code
Bell Cut
2-Wire Fire Trouble
Rcvr Fail-to-Respond
Receiver Tamper
Receiver JAM
Tx Low Battery
Tx Supervisory Failure
Smoke Low Battery
Smoke Sup. Failure
F1
F1
F1
F1
F1
F1
F1
F1
F1
If reporting using Point ID, a unique code will be
sent for each of the following System Troubles.
System Trouble
Point ID Report Codes
Bell Cut
2-Wire Fire Trouble
Rcvr Fail-to-Respond
Receiver Tamper
Receiver JAM
Tx Low Battery
Tx Supervisory Failure
*Smoke Low Battery
*Smoke Sup. Failure
CODE 1 321 G00 ZN000-BELL 1 TROUBLE
CODE 1 373 G00 ZN000-FIRE LOOP TRBLE
CODE 1 382 G00 ZN000-SENSOR TROUBLE
CODE 1 145 G00 ZN000-EXP. MODL. TAMPER
CODE 1 373 G00 ZN000-FIRE LOOP TRBLE
CODE 1 384 G00 ZN00n-RF TRAN LOW BATT
CODE 1 381 G00 ZN00n-SUPERVSN LOSS RF
CODE 1 384 G00 ZN00n-RF TRAN LOW BATT
CODE 1 381 G00 ZN00n-SUPERVSN LOSS RF
*Smoke Detectors 1 - 4 report as ZN009 - ZN012
A 300 (SYSTEM TROUBLE RST) code is sent if a restore is
reported after multiple troubles.
23
Wi846c
page 23
Tuesday, September 16, 1997 10:36
WI846C XP-600 Installation Instructions
6\VWHP 7URXEOHV
*
Keypad Beeps or
SYSTEM
Flashes
1 Beep
2 Beeps
Zone LED
ON
System Trouble
Condition
Cause/Action
1
2
AC Power Failure
Low Battery
This trouble will occur if AC power is not present. Ensure that the transformer is connected to an unswitched power source.
3
Communication
Failure/PCPreset Fail
The system was not able to report to central station. Check panel programming and telephone line wiring. The trouble will
clear after it has been acknowledged by viewing the system trouble as long as the telephone line has passed a line cut test
(tested automatically by the panel). The Panel did not sucsessfully connect and download/upload with the commputer
running PCPreset - check Auto Download ID number, Callback Number or PCPreset Setup.
4
Telephone Line Cut
1
2
3
Bell/Siren line Cut
2-wire Fire Trouble
Rcvr Fail-to-Respond/Rcvr
Tamper
Receiver Jam
The telephone line has failed. If telephone service has been temporarily interrupted, the trouble will clear when restored and
acknowledged by viewing the system trouble.
There is a problem with the Bell or Siren wiring. EOL2.2K resistor must be installed.
4
If there has been a recent power failure, the battery may be partially depleted and must be recharged by the control panel. If
the trouble does not go away in 24 hours, replace the battery.
There is a problem with the wiring of the Fire Zone.
The receiver is not responding to the panel. The red LED on the receiver should be flashing, refer to WI848. The cover is off
the receiver causing a tamper signal to be transmitted.
A signal is blocking the normal reception of transmissions from the wireless devices. Ensure that the green LED on the
receiver is not on continuously, refer to receiver manual WI848.
The battery in the wireless transmitter is low and should be replaced. This transmitter is on the zone corresponding to the
number of the zone light flashing. The replacement battery for the GEM Trans2 door/window transmitter and the GEM PIR
wireless motion detector is the Duracell DL123A. (2 required for the GEM-PIR) WARNING: Replace batteries only with the
same type as specified above. Use of another battery may present a risk of fire or explosion. Do not recharge or disassemble
battery or dispose of in fire.
3 Beeps
1-6
Wireless
Transmitter Low Battery
4 Beeps
1-6
The panel has not received a supervisory signal from the transmitter within the time programmed. Check Wireless
Supervisory Timer [16] Programming. Check the placement of the transmitter and receiver, refer to WI848.
5 Beeps
1-4
Wireless
Transmitter
Supervisory Failure
Wireless Smoke Detector Low
Battery
6 Beeps
1-4
Wireless Smoke Detector Supervisory
The panel has not received a supervisory signal from the wireless smoke detector within the programmed time. Check
Wireless Smoke Supervisory Timer [17] Programming. Check the placement of the wireless smoke detector and receiver,
refer to WI848.
7 Beeps
1-6
Zone Trouble
The panel has one or more of the following 3 possible troubles: Zone Short, Transmitter Tamper or Dual Tech Self Test Fail.
The battery in the wireless smoke detector is low and should be replaced. This wireless smoke detector should be marked
with a number corresponding to the number of the zone light flashing. The replacement batteries required are *Duracell 9 Volt
Alkaline (2).
24
Wi846c
page 24
Tuesday, September 16, 1997 10:36
7URXEOHVKRRWLQJ
1. The bell output drops to about 3 volts in
alarm.
The battery/bell circuit is protected by a PC
board trace which may have burned open
by reversal of the battery leads. It is on the
back of the PC board just adjacent to the
red & black battery leads. Send in for service if this occurs.
2. How do I remove the Keypad Sounder
on Alarm?
The keypad sounder follows the Burg Output. If you need to remove the Keypad
Sounder, then you must remove the Burg
Output from that zone.
3. How do I activate Chime by Zone?
The Chime feature will automatically be
assigned to all zones, except for the following:
1. Zones programmed as Home/Away
with Delay.
Zones programmed as Exit/Entry
Followers
2. Zones programmed for 24 Hour Protection. To Activate/Deactivate the
.
chime mode, Press
4. When using a piezo on the Bell Output,
it constantly buzzes.
This is due to the fact that there is a
constant loop current flowing through the
Bell circuit for supervision. To eliminate
this, cut resistor R26 which is located
directly above Terminal 9 just below the
heat sink.
5. Where are the fuses?
The control panel incorporates advanced
circuitry which automatically limits the current when an over current condition exists
without the use of traditional fuses. The
circuit will restore automatically when the
over current condition is corrected.
6. The PGM Output Pulses in Alarm.
When the PGM lug of the control panel is
programmed for an Armed indication it also
incorporates an Alarm Memory function
which will indicate that the system is in an
Alarm condition. If this output is being used
to trigger a long range radio, it can be
converted to a steady output with the use of
a capacitor, negative to PGM Terminal 15,
Pos to Aux. Pwr. Term 12. (220 mF Electrolytic Capacitor, 25 Volts. Increase to 470
mF if necessary)
7. I short out the bell and the system does
not indicate Bell Trouble.
The Bell Supervision circuit is only designed to detect a "Bell Cut", it does not
supervise for a short on the Bell.
25
Wi846c
page 25
Tuesday, September 16, 1997 10:36
WI846C XP-600 Installation Instructions
8. How do I remove Keypad Sounder on
Alarm?
The keypad sounder follows the Burg Output. If you need to remove the Keypad
Sounder, then you must remove the Burg
Output from that zone.
9. Transmitters not responding?
Open Transmitter case - Keypad should go
into X-Mitter Tamper Trouble. If not:
Check Receiver Red LED should be
flashing once approx. once a second.
Check Receiver wiring.
Check Programming of Transmitter ID.
If Keypad does go into X-Mitter Tamper
Trouble, check:
Transmitter point is programmed correctly.
Transmitter is wired correctly:
If using external switch, make sure it is
wired to point 1, and point 2 is jumped
out.
If using internal reed, make sure J1 is
cut and both Point 1 and Point 2 terminals are jumped out.
10. Keypad LEDs Flicker.
The Keypad is not receiving a POLL from
the Panel.
Check Keypad wiring.
1. The Panel is in the process of being
Uploaded/Downloaded.
2. The panel is powering up. LED’s
will flicker until panel has reset and
is polling the keypad.
3. The connection from the control
panel to the keypad is open.
12. No Keypad Chime?
The keypad sounder is turned off with the
command. This command will si-
lence all Keypad sounds except keypad
to turn
sounder on alarm. Enter
keypad sounds back on.
11. No Keypad Entry Sounder during Entry Time?
The keypad sounder is turned off with the
command. This command will
silence all Keypad sounds except keypad
to turn
sounder on alarm. Enter
keypad sounds back on.
26
Wi846c
page 26
Tuesday, September 16, 1997 10:36
XP-600 WIRING DIAGRAM
This equipment should be installed in accordance with Chapter 2
of the National Fire Alarm Code, ANSI/NFPA 72-1993 (National
Fire Protection Association Batterymarch Park, Quincy MA
02269). and local codes. Information describing proper installation, operation, testing, maintenance, evacuation planning, and
repair service is to be provided with this equipment. UL Listed
Energy Cable is required.
(REFER TO INSTALLATION INSTRUCTIONS WI47C)
E1
RED
RESIDENTIAL BURG (4 HOUR STANDBY)
COMBINED STANDBY = 500 mA
BELL = 2.0 AMP
RECHARGEABLE
BATTERY
12 VDC 4AH OR 7AH
E2
(2)
RESIDENTIAL FIRE (4 HOUR STANDBY)
COMBINED STANDBY = 500 mA
BELL = 65 mA
BLACK
(3)
RESIDENTIAL FIRE (24 HOUR STANDBY)
COMBINED STANDBY = 120 mA
BELL = 95 mA
COLD WATER GROUND
CONNECTION
USE ONLY COLD-WATER
PIPE OR BURIED GROUND
ROD. USE AT LEAST #16
AWG WIRE.
-7
BELL
GND
(2)
COMBINED STANDBY = KEYPAD CURRENT +
AUX POWER CURRENT + FIRE POWER + PGM
CURRENT.
ZONE 2
ZONE 3
RING
.
2.2K EOLR
(SUPERVISED)
TELCO
PHONE
To RJ31X
(Supervised)
RPX-6
WARNING
TO PREVENT RISK
OF ELECTRIC SHOCK
DISCONNECT TELEPHONE
LINES PRIOR TO SERVICING
GEM-RECV-XP8
12
+PWR
(E)
Normally Open Zone Wiring
Wire the normally open contact
as shown (Zone 4). Program
the zone for Open Circuit [06]
operation.
.
24 HOUR STANDBY REQUIRES A 7AH BATTERY.
ZONE 1
19
TIP
BRN
ALL ZONE RESISTORS MUST BE INSTALLED,
EVEN IF ZONE IS NOT USED.
.
(1)
(E)
18
RING
GRAY
(E)
.
17
TIP
GRN
(E)
.
(E)
ZONE 6
A'
ZONE 5
.
.
*2/'
ZONE 4
/2
(1)
16
Programmable
Output
+
P$ 0$;
(Z)
%/.
(Z)
15
GND GREEN PGM
(-)
REMOTE BUS
*51
+
(Z)
14
+PWR
+
2.2K EOLR
(3)
+10 -11 +12 -13
+
(Z)
:+,7( 5('
-9
FIRE
+
3.9K
25$1*(
+8
5('
EARTH
GROUND
+6
.
GOLD
RED RED
+5
.
RED
-4
FIRE
PWR
.
Zone
TM
Doubling
Resistors
+3
AUX POWER OUTPUT 10-12.5 VDC
EZ
2
RED
2.2K
(E)
1
16 VAC 20 VA
TRANSFORMER
NAPCO TRF12
(OR EQUIVALENT
SEE WI850).
Class 2
Transformer.
DO NOT
connect to
switched
outlet.
ALL OUTPUTS ARE CURRENT LIMITED
FT2200
ZONE 4
XP-600 Terminals
RED
(Z)
4-Wire Fire Wiring
BLACK
BROWN
(E)
BROWN
Power
Out (+)
Power
Out (-)
Power
In (+)
Power
In (-)
Fire Loop Fire Loop
Out
In
8 Fire Power
7 Ground
8 Fire Power
9 Fire
ZONE 1
27
Wi846c
page 27
Tuesday, September 16, 1997 10:36
WI846C XP-600 Installation Instructions
NAPCO LIMITED WARRANTY
NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from manufacturing defects in materials and workmanship for thirty-six months following the date of manufacture.
NAPCO will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user.
This warranty shall not apply to any equipment, or any part thereof, which has been repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to acts of God, or
on which any serial numbers have been altered, defaced or removed. Seller will not be responsible for any dismantling or reinstallation charges.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF
MERCHANTABILITY OR A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE
PART OF NAPCO.
Any action for breach of warranty, including but not limited to any implied warranty of merchantability, must be brought within the six months following the end of the warranty period. IN NO CASE
SHALL NAPCO BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF
THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.
In case of defect, contact the security professional who installed and maintains your security system. In order to exercise the warranty, the product must be returned by the security professional,
shipping costs prepaid and insured to NAPCO. After repair or replacement, NAPCO assumes the cost of returning products under warranty. NAPCO shall have no obligation under this warranty, or
otherwise, if the product has been repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to accident, nuisance, flood, fire or acts of God, or on which any
serial numbers have been altered, defaced or removed. NAPCO will not be responsible for any dismantling, reassembly or reinstallation charges. This warranty contains the entire warranty. It is the
sole warranty and any prior agreements or representations, whether oral or written, are either merged herein or are expressly canceled. NAPCO neither assumes, nor authorizes any other person
purporting to act on its behalf to modify, to change, or to assume for it, any other warranty or liability concerning its products. In no event shall NAPCO be liable for an amount in excess of NAPCO's
original selling price of the product, for any loss or damage, whether direct, indirect, incidental, consequential, or otherwise arising out of any failure of the product. Seller's warranty, as hereinabove
set forth, shall not be enlarged, diminished or affected by and no obligation or liability shall arise or grow out of Seller's rendering of technical advice or service in connection with Buyer's order of the
goods furnished hereunder.
NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED WEEKLY.
Warning: Despite frequent testing, and due to, but not limited to, any or all of the following; criminal tampering, electrical or communications disruption, it is possible for the system to fail to perform
as expected. NAPCO does not represent that the product/system may not be compromised or circumvented; or that the product or system will prevent any personal injury or property loss by burglary,
robbery, fire or otherwise; nor that the product or system will in all cases provide adequate warning or protection. A properly installed and maintained alarm may only reduce risk of burglary, robbery,
fire or otherwise but it is not insurance or a guarantee that these events will not occur. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY
DAMAGE, OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. Therefore, the installer should in turn advise the consumer to take any and all precautions for his
or her safety including, but not limited to, fleeing the premises and calling police or fire department, in order to mitigate the possibilities of harm and/or damage. NAPCO is not an insurer of either the
property or safety of the user's family or employees, and limits its liability for any loss or damage including incidental or consequential damages to NAPCO's original selling price of the product
regardless of the cause of such loss or damage.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation of incidental or consequential damages, or differentiate in their treatment of
limitations of liability for ordinary or gross negligence, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC.
This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio
and television reception. It has been type tested and found to comply with the limits for a Class-B computing device in accordance with the specifications in Subpart J of Part 15 of FCC Rules, which
are designed to provide reasonable protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: reorient the receiving antenna; relocate the computer with respect to the
receiver; move the computer away from the receiver; plug the computer into a different outlet so that computer and receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal
Communications Commission helpful: <169>How to Identify and Resolve Radio-TV Interference Problems.<170> This booklet is available from the U.S. Government Printing Office, Washington, DC
20402; Stock No. 004-000-00345-4.
28
Wi846c
page 28
Tuesday, September 16, 1997 10:36
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement