3M MP7640i Projector User Guide Manual Operating Instruction Pdf

3M MP7640i Projector User Guide Manual Operating Instruction Pdf
MP7640i/MP7740i
Multimedia Projector
Operator's Guide
Downloaded from ProjectorsManual.com Manuals
MP7640i/MP7740i Multimedia Projector
Operator's Guide
Thank you for purchasing this projector.
WARNING • Please read the accompanying manual “Product Safety Guide"
and this “Operator's Guide” thoroughly to ensure correct usage through
understanding. After reading, store this instruction manual in a safe place for
future reference.
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual
• The reproduction, transmission or use of this document or contents is not permitted without express
written authority.
TRADEMARK ACKNOWLEDGEMENT :
• PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation.
• Apple, Mac and ADB are registered trademarks of Apple Computer, Inc.
• VESA and SVGA are trademarks of the Video Electronics Standard Association.
• Windows is a registered trademark of Microsoft Corporation.
• All other trademarks are the property of their respective owners.
CONTENTS
Page
Page
PROJECTOR FEATURES ............... 2
PREPARATIONS ............................. 2
PART NAMES .................................. 4
SETTING UP THE PROJECTOR .... 6
CONNECTING YOUR DEVICES ..... 8
USING
THE REMOTE CONTROL ........... 12
TURNING ON THE POWER .......... 14
TURNING OFF THE POWER ........ 16
ADJUSTING THE VOLUME ........... 17
TEMPORARILY
SOUND THE SOUND ................... 17
ADJUSTING THE POSITION ........ 18
USING THE AUTOMATIC
ADJUSTMENT FEATURE ........... 19
CORRECTING
KEYSTONE DISTORTIONS ......... 20
USING THE MAGNIFY FEATURE ... 21
FREEZING THE SCREEN ............. 21
SIGNAL SEARCHING ................... 22
SELECTING
THE ASPECT RATIO ..................... 22
TEMPORARILY
BLANKING THE SCREEN .......... 22
USING THE MENU FUCTIONS ..... 23
MULTIFUNCTIONAL
SETTINGS .................................... 24
THE LAMP ..................................... 29
THE AIR FILTER ............................ 31
OTHER CARE ................................ 33
WHAT TO DO
WHEN YOU THINK A MACHINE
DEFECT HAS OCCURRED ......... 34
SPECIFICATIONS .......................... 37
ACCESSORIES .............................. 38
Downloaded from ProjectorsManual.com Manuals
1
This liquid crystal projector is used to project
various computer signals as well as NTSC / PAL /
SECAM video signals onto a screen. Little space
is required for installation and large images can
easily be realized.
PROJECTOR
FEATURES
●Ultra High Brightness
●Keystone Distortion Correction
●Partial Magnification Function
●Whisper Mode Equipped
Crisp, ultra-bright presentations is achieved
by using a UHB (ultra high brightness) lamp
and a highly efficient optical system
Interesting parts of images can be magnified
for closer viewing
PREPARATIONS
Quick correction of distorted images electrically
Special mode is available for reducing
projector noise to achieve quieter operation
Your projector should come with the items
shown below. Check to make sure that all the
items are included. Contact your dealer if
anything is missing.
NOTE • Keep the original packing material for future reshipment.
Power cord
(US Type)
Power cord
(UK Type)
Power cord
(Europe Type)
RGB cable
Video/Audio
cable
(with white lead)
Component Video
cable
(with green lead)
Projector
(with Lens Cap)
MP7640i/MP7740i
Multimedia Projector
Product Safety Guide
MP8765 Projecteur multimedia - Guide de Securite de Produit
MP8765 Multimedia-Projektor - Sicherheitsanleitung des Gerats
MP8765 Proyector de Multimedia - Guía de Seguridad del Producto
MP8765 Proiettore Multimediale - Guida di Sicurezza del Prodotto
MP8765 Multimedia Projector - Veiligheidgids op Product
MP8765 Projector dos Multimedia - Guia da Seguranca de Produto
MP8765 Multimedia Projektør- Bruksabvisning for Produktsakerhets
Operator's Guide
Product Safety Guide
Warranty
Quick Start Guide
STANDBY/ON
VIDEO
ASPECT
RGB
SEARCH
AUTO
BLANK
VOLUME
MAGNIFY
ON
MUTE
OFF
FREEZE
KEYSTONE
Stereo Mini-Cable
POSITION
Two AA batteries
(for the
remote control)
Soft carrying case
2
Downloaded from ProjectorsManual.com Manuals
MENU
ENTER
ESC
RESET
Remote control
WARNING Precautions to observe in regards to the power cord: Please use extra
caution when connecting the projector's power cord as incorrect or faulty
connections may result in FIRE AND/OR ELECTRICAL SHOCK. Please adhere to the
following safety guidelines to insure safe operation of the projector:
• Only plug the power cord into outlets rated for use with the power cord's specified voltage range.
• Only use the power cord that came with the projector.
• NEVER ATTEMPT TO DEFEAT THE GROUND CONNECTION OF THE THREEPRONGED PLUG!
• Make sure that you firmly connect the power cord to the projector and wall outlet.
1
Connect your devices to the projector
2
Insert the batteries into the remote
control
3
Connect the power cord
Connect your computer, VCR and/or other
devices you will be using to the projector.
8
∼ 11
12
(1) Connect the connector of the electrical power cord to the AC inlet of the main unit.
(2) Firmly plug the power cord's plug into the outlet
Power outlet
(2)
(1)
Power cord
AC inlet
Downloaded from ProjectorsManual.com Manuals
3
PART NAMES
THE PROJECTOR
Indicates the corresponding
reference page
15 Zoom ring
15 Focus ring
13 Remote sensor
14 Power switch
Lens
3
AC power inlet
(to the Power Cord)
Ventilation Openings
(Intake)
14 Slide Lens Door
6
Foot Adjuster
24 RESET button
20 KEYSTONE button
15 INPUT button
14 STANDBY/ON button
6
Foot Adjuster button
25 LAMP indicator
26 TEMP indicator
14 POWER indicator
23 MENU button
Ventilation Openings
(Exhaust)
26 Air filter
Speaker
6
4
Rear Foot Adjuster
Downloaded from ProjectorsManual.com Manuals
Terminal Panel
THE TERMINAL PANEL
10 RGB port
Technical
13 Remote sensor
4 CONTROL port
11 COMPONENT
Y port
CB/PB port
CR/PR port
10 AUDIO port
10 AUDIO
R port
11 S-VIDEO port
L port
11 VIDEO port
THE REMOTE CONTROL
22 SEARCH button
14 STANDBY/ON button
RGB button 15
STANDBY/ON
VIDEO button 15
VIDEO
RGB
SEARCH
19 AUTO button
ASPECT
AUTO
BLANK
22 BLANK button
ASPECT button 22
VOLUME
MAGNIFY
17 VOLUME button
ON
MAGNIFY buttons 21
MUTE
17 MUTE button
OFF
FREEZE
KEYSTONE
FREEZE button 21
20 KEYSTONE button
POSITION
MENU
POSITION button 18
23 MENU button
ENTER
,
,
,
23
Cursor buttons
ESC
ESC button 23
RESET
24 RESET button
23 ENTER button
Downloaded from ProjectorsManual.com Manuals
5
SETTING UP THE PROJECTOR
CAUTION • Install the projector in a suitable environment according to instructions
of the accompanying manual “Product Safety Guide” and this manual.
• If you press the elevator buttons without holding the projector, the projector might
crash down, overturn, smash your fingers and possibly result in malfunction. To
prevent damaging the projector and injuring yourself, ALWAYS HOLD THE
PROJECTOR whenever using the elevator buttons to adjust the elevator feet.
Angle Adjustment
Use the foot adjusters on the bottom of the projector to adjust the projection
angle. It is variable within 0˚ to 10˚ approximately.
1
Lift up the front side of the
projector, and pressing the foot
adjuster button, adjust the
projection angle
Press the foot adjuster button
2
Release the button to lock at the
desired angle
3
Make the rear foot adjuster screw to
adjust the left-right slope
Rear Foot Adjuster
6
Downloaded from ProjectorsManual.com Manuals
Adjusting the Screen Size and Projection Distance
Refer to the illustrations and tables below to determine the screen size and
projection distance.
The values shown in the table are calculated for a full size screen
(MP7640i: 800x600 pixels / MP7740i: 1024x768 pixels).
a:Distance from the projector to the screen (±10%)
b:Distance from the lens center to the bottom of the screen (±10%)
The screen
Top view
If 4:3 aspect ratio
4
3
Screen size
[inch (m)]
Lens center
Side view
b
(1.0)
(1.5)
(2.0)
(2.5)
(3.0)
(3.8)
200 (5.0)
a
The screen
40
60
80
100
120
150
Top view
a [inch (m)]
Min.
Max.
37
57
77
96
116
145
(0.9)
(1.5)
(1.9)
(2.4)
(2.9)
(3.7)
194 (4.9)
46
69
93
116
139
174
(1.2)
(1.8)
(2.4)
(2.9)
(3.5)
(4.4)
233 (5.9)
b
[inch (cm)]
3
5
7
9
10
13
(8.7)
(13.1)
(17.4)
(21.8)
(26.1)
(32.7)
17 (43.5)
If 16:9 aspect ratio
16
9
Screen size
[inch (cm)]
Lens center
Side view
b
a
30
40
60
80
100
120
150
(0.8)
(1.0)
(1.5)
(2.0)
(2.5)
(3.0)
(3.8)
200 (5.0)
Downloaded from ProjectorsManual.com Manuals
a [inch (m)]
Min.
Max.
30
41
62
83
105
126
158
(0.8)
(1.0)
(1.6)
(2.1)
(2.7)
(3.2)
(4.0)
212 (5.4)
38
50
76
101
127
152
190
b
[inch (cm)]
(1.0)
(1.3)
(1.9)
(2.6)
(3.2)
(3.9)
(4.8)
0
0
1
1
1
1
2
(1)
(1)
(2)
(2)
(3)
(4)
(4)
254 (6.4)
2
(6)
7
CONNECTING YOUR DEVICES
Devices You Can Connect to the Projector
(Refer to this section for planning your device
configuration to use for your presentation.)
CAUTION • Incorrect connecting could result in fire or electrical shock. Please
read this manual and the separate “Product Safety Guide”.
ATTENTION Precautions to observe when connecting other devices to the projector
• Whenever attempting to connect other devices to the projector, please thoroughly
read the manual of each device to be connected.
• TURN OFF ALL DEVICES prior to connecting them to the projector. Attempting to
connect a live device to the projector may generate extremely loud noises or other
abnormalities that may result in malfunction and/or damage to the device and/or
projector. Refer to the “Technical” for the pin assignment of connectors and
RS-232C communication data.
• Make sure that you connect devices to the correct port. Incorrect connection may
result in malfunction and/or damage to the device and/or projector.
• Some cables have to be used with core set. Use the accessory cable or a designatedtype cable for the connection. For cables that have a core only at one end,
connect the core to the projector.
• Secure the screws on the connectors and tighten.
Indicates the
corresponding
reference page
11 DVD players
10 Laptop computers
11 VCRs
10 Desktop computers
8
Downloaded from ProjectorsManual.com Manuals
Ports and Cables
Refer to the table below to find out which projector port and cable to use for connecting a
given device. Use this table for determining which cables to prepare.
Function
Projector Port
Connection Cables
RGB input
RGB IN
RGB cable
with D-sub 15-pin shrink jack and
inch thread screws
AUDIO input
(from the computer)
AUDIO IN
Audio cable with stereo mini jack
RS-232C communication
CONTROL
RS-232C cable
S-video input
S-VIDEO IN
S-video cable
with mini DIN 4-pin jack
Video input
VIDEO IN
Audio/video cable
COMPONENT VIDEO Y
Component video input
COMPONENT VIDEO CB/PB
Component video cable
COMPONENT VIDEO CR/PR
Audio input
(from video equipment)
AUDIO IN L
AUDIO IN R
Audio/video cable or
Audio cable with RCA jack
NOTE About Plug-and-Play Capability
• This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be achieved by
connecting this projector to computers that are VESA DDC (display data channel)
compatible. Please take advantage of this function by connecting the accessory RGB
cable to the RGB IN port (DDC 1/2B compatible). Plug-and-Play may not work
properly if any other type of connection is attempted.
• Plug-and-Play is a system composed of the computer, its operating system and
peripheral equipment (i.e. display devices).
• Please use the standard drivers as this projector is a Plug-and-Play monitor.
Downloaded from ProjectorsManual.com Manuals
9
CONNECTING YOUR DEVICES (continued)
Connecting to a Computer
ATTENTION Whenever attempting to connect a laptop computer to the projector,
be sure to activate the laptop's RGB external image output (set the laptop to CRT
display or to simultaneous LCD and CRT display). For details on how this is done,
please refer to the instruction manual of the corresponding laptop computer.
A
B
B
A
RGB IN
RGB cable
Analogue
RGB OUT
AUDIO OUT
AUDIO cable
AUDIO IN
Laptop computer
Desktop computer
NOTE
• Some computers may have multiple display screen modes. Use of some of these
modes will not be possible with this projector.
• For some RGB input modes, the optional Mac adapter is necessary.
10
Downloaded from ProjectorsManual.com Manuals
Connecting to a DVD Player
A A A
S-VIDEO IN
S-VIDEO cable
If using a S-video
connection
S-VIDEO OUT
AUDIO/VIDEO OUT
AUDIO/VIDEO cable
COMPONENT VIDEO OUT
COMPONENT cable
If using a component
video connection
C
AUDIO/VIDEO IN
B
COMPONENT VIDEO IN
A
B B B
C
If using an audio/video
connection
DVD player
Connecting to a VCR
B
B
S-VIDEO IN
S-VIDEO cable
If using a S-video
connection
S-VIDEO OUT
AUDIO/VIDEO OUT
AUDIO/VIDEO cable
AUDIO/VIDEO IN
A
A A A
VCR
Downloaded from ProjectorsManual.com Manuals
11
USING THE REMOTE CONTROL
Putting batteries into the remote control unit
CAUTION Precautions to observe in regards to the batteries
Always handle the batteries with care and use them only as directed. Improper use may result in
battery cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.
• Keep the battery away from children and pets.
• Be sure to use only the batteries specified for use with the remote control. Do not mix new batteries with used ones.
• When inserting batteries, verify that the plus and minus terminals are aligned correctly (as indicated in the remote control).
• When you dispose the battery, you should obey the law in the relative area or country.
1
2
3
12
Remove the battery cover
Slide back and remove the battery cover in the direction of the
arrow.
Insert the batteries
Align and insert the two AA batteries (that came with the
projector) according to their plus and minus terminals (as
indicated in the remote control).
Close the battery cover
Replace the battery cover in the direction of the arrow and
snap it back into place.
Downloaded from ProjectorsManual.com Manuals
Operating the remote control
e
gr
de
es
rees
30 deg
30
s
ee
gr
de
rees
45 deg
45
• The remote control works with both
the projector's front and rear remote
sensors.
• The range of the remote sensor on
the front is 3 meters with a 90-degree
range (45 degrees to the left and
right of the remote sensor), and back
is 3 meters with a 60-degree range.
• Since the remote control uses
infrared light to send signals to the
projector (Class 1 LED), be sure to
use the remote control in an area free
from obstacles that could block the
remote control's output signal to the
projector.
ATTENTION Precautions to observe when using the remote control
• Do not drop or otherwise expose the remote control to physical impact.
• Do not get the remote control wet or place it on wet objects. Doing so may result in
malfunction.
• Remove the batteries from the remote control and store them in a safe place if you
won't be using the remote control for an extended period.
• Replace the batteries whenever the remote control starts to malfunction.
• When strong light, such as direct sunlight or light from an extremely close range
(such as from an inverter fluorescent lamp), hits the projector's remote sensor, the
remote control may cease to function. Adjust the direction of the projector to keep
light from directly hitting the projector's remote sensor.
Downloaded from ProjectorsManual.com Manuals
13
TURNING ON THE POWER
Precautions
8
Connect all devices to be used to the projector prior to turning on the power.
∼ 11
WARNING When the power is ON, a strong light is emitted. Do not look into the
lens.
1
STANDBY/ON
VIDEO
RGB
Make sure that the power cord is firmly and
correctly connected to the projector and outlet
SEARCH
ASPECT
AUTO
3
BLANK
VOLUME
MAGNIFY
ON
MUTE
2
OFF
FREEZE
Turn on the projector's
power
Set the power switch to [ | ] (ON).
The projector will go to STANDBY
mode and the POWER indicator
will light to solid orange.
KEYSTONE
Control panel
POWER indicator
KEYSTONE
RESET
LANP
POWERTENP
LANP
TENP
POWER
STANDBY/ON INPUT KEYSTONE
RESET
power switch
3
• The projector begins warming up and the POWER
indicator blinks green.
STANDBY/ON
• The POWER indicator stops blinking
and lights to solid green once the
projector's power is completely on.
NOTE Turn the
power on/off in
right order.
• Power on the
projector before the
computer or video
tape recorder.
• Power off the
projector after the
computer or video
tape recorder.
14
Press the STANDBY/ON button (control
panel or remote control)
4
Open the slide lens door
The picture is projected.
Downloaded from ProjectorsManual.com Manuals
Selecting an Input Signal
5
Using the remote control
If selecting RGB input
Press the RGB button
Press the INPUT button
Press this button to swich to the devices
connected to RGB IN as illustrated
below.
RGB
VIDEO IN
S-VIDEO IN
COMPONENT VIDEO
Press this button to toggle between the
devices connected to VIDEO IN, SVIDEO IN and COMPONENT VIDEO. As
illustrated below, each time you press
the VIDEO button, the projector
switches between VIDEO IN, S-VIDEO
IN and COMPONENT VIDEO. Select the
signal you wish to project.
VIDEO IN
As illustrated below, each time you
press the INPUT button, the projector
switches between its input signal
ports. Select the signal you wish to
project.
INPUT
RGB IN
If selecting video input
Press the VIDEO button
VIDEO
Using the projector's control panel
RGB IN
COMPONENT VIDEO
VIDEO IN
S-VIDEO IN
S-VIDEO IN
COMPONENT VIDEO
6
Use the zoom ring to adjust the
screen size
7
Use the focus ring to focus the
picture
Downloaded from ProjectorsManual.com Manuals
15
TURNING OFF THE POWER
1
The message "Power off?" will appear on the screen for approximately 5 seconds.
STANDBY/ON
VIDEO
RGB
ASPECT
STANDBY/ON
SEARCH
AUTO
Press the STANDBY/ON button (control
panel or remote control)
BLANK
VOLUME
MAGNIFY
ON
MUTE
OFF
FREEZE
2
KEYSTONE
POSITION
Press the STANDBY/ON button again while the "Power off?"
message is visible. The projector lamp goes off and starts cooling
down. The POWER indicator blinks orange while the lamp cools
down. (Pressing the STANDBY/ON button while the POWER
indicator is blinking orange has no effect.)
STANDBY/ON
The system goes into the STANDBY mode after
cooling down and the POWER indicator stops
blinking orange and then lights to solid orange.
MENU
ENTER
ESC
RESET
Control panel
3
LANP
TENP
POWER
STANDBY/ON INPUT KEYSTONE
Press the STANDBY/ON button again
(control panel or remote control)
RESET
Check that the POWER
indicator stops
blinking and lights to
solid orange.
Switch the power
switch to [O] (OFF).
POWER indicator
KEYSTONE
RESET
LANP
POWERTENP
power switch
4
NOTE
• Except in
emergencies, follow
the abovementioned
procedure for
turning power off.
16
Confirm that the POWER indicator has gone
off and then close the slide lens door.
When the projector has completed powering down, the
POWER indicator will go off.
Downloaded from ProjectorsManual.com Manuals
ADJUSTING THE VOLUME
1
STANDBY/ON
VIDEO
RGB
ASPECT
SEARCH
AUTO
BLANK
Press the VOLUME button
VOLUME
As illustrated on the right, a dialog will
appear on the screen to aid you in adjusting
the volume.
VOLUME
VOLUME
MAGNIFY
ON
MUTE
16
OFF
FREEZE
KEYSTONE
2
POSITION
MENU
,
buttons to adjust
Press the VOLUME button again to close the dialog and
complete this operation. (Even if you don't do anything, the
dialog will automatically disappear after a few seconds.)
ENTER
ESC
Press the
the volume
RESET
VOLUME
Press this to increase the volume
Press this to decrease the volume
16
TEMPORARILY MUTING THE SOUND
STANDBY/ON
VIDEO
ASPECT
RGB
SEARCH
AUTO
BLANK
VOLUME
MAGNIFY
ON
MUTE
OFF
FREEZE
1
Press the MUTE button
As illustrated on the right, a dialog will appear on the
screen indicating that you have muted the sound. Press
the VOLUME button to close the dialog. (Even if you don't
do anything, the dialog will automatically disappear after
a few seconds.)
Press the MUTE button again to restore the sound.
KEYSTONE
VOLUME
POSITION
MENU
MUTE
ENTER
ESC
RESET
16
Downloaded from ProjectorsManual.com Manuals
17
ADJUSTING THE POSITION
1
STANDBY/ON
VIDEO
ASPECT
RGB
SEARCH
AUTO
Press the POSITION button
As illustrated on the right, a dialog will appear on the screen
to aid you in adjusting the position.
BLANK
VOLUME
MAGNIFY
ON
MUTE
POSITION
OFF
FREEZE
KEYSTONE
POSITION
POSITION
MENU
ENTER
ESC
RESET
2
Use the
,
the position
,
,
buttons to adjust
When you want to initialize the position, press the RESET
button during adjustment.
Press the POSITION button again to close the dialog and
complete this operation. (Even if you don't do anything, the
dialog will automatically disappear after a few seconds.)
This function is only available for RGB IN input.
18
Downloaded from ProjectorsManual.com Manuals
USING THE AUTOMATIC ADJUSTMENT FEATURE
1
Press the AUTO button
AUTO
STANDBY/ON
VIDEO
ASPECT
RGB
SEARCH
AUTO
BLANK
VOLUME
MAGNIFY
Automatic Adjustment for RGB Input
ON
MUTE
OFF
FREEZE
KEYSTONE
POSITION
MENU
ENTER
ESC
Horizontal position (H. POSIT), vertical position (V.
POSIT), clock phase (H. PHASE) and horizontal size (H.
SIZE) are automatically adjusted.
Make sure that the application window is set to its
maximum size prior to attempting to use this feature.
Dark pictures may still be incorrectly adjusted. Use a
bright screen when adjusting.
RESET
Automatic Adjustment for Video Input
The signal type best suited for the respective input
signal is selected automatically.
This feature is available only if VIDEO is set to AUTO in
the INPUT menu.
NOTE
The automatic adjustment operation requires approximately 10 seconds. Also, please
note that it may not function correctly with some input signals.
Downloaded from ProjectorsManual.com Manuals
19
CORRECTING KEYSTONE DISTORTIONS
1
STANDBY/ON
VIDEO
ASPECT
RGB
SEARCH
AUTO
BLANK
Press the KEYSTONE button
As illustrated on the right, a dialog will appear
on the screen to aid you in correcting the
distortion.
KEYSTONE
KEYSTONE
VOLUME
MAGNIFY
ON
MUTE
16
OFF
FREEZE
KEYSTONE
POSITION
MENU
ENTER
ESC
RESET
2
Use the
distortion
,
buttons to correct the
Press the KEYSTONE button again to close the dialog and
complete this operation. (Even if you don't do anything, the
dialog will automatically disappear after a few seconds.)
NOTE
• This function may not be work well with some types of input signals.
• The adjustable range for correcting keystone distortions will vary with the type of
input signal.
20
Downloaded from ProjectorsManual.com Manuals
USING THE MAGNIFY FEATURE
1
Press the MAGNIFY (ON) button
The projector enters MAGNIFY mode.
MAGNIFY
ON
STANDBY/ON
VIDEO
ASPECT
RGB
SEARCH
AUTO
BLANK
VOLUME
MAGNIFY
ON
MUTE
the POSITION button, then use the
, ,
2 Press
,
buttons to select the area to enlarge and then
OFF
FREEZE
press the POSITION button again to confirm your
selection
KEYSTONE
POSITION
POSITION
POSITION
MENU
ENTER
ESC
RESET
3
Press the
,
buttons to zoom in and
out of the selected area.
Press the MAGNIFY (OFF) button to exit MAGNIFY mode
and restore the screen to normal. (The projector will also
automatically exit MAGNIFY mode if there is a change in the
input signal's state.)
NOTE
The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT,
AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signal's state.
FREEZING THE SCREEN
MAGNIFY
VOLUME
ON
MUTE
POSITION
KEYSTONE
Press the FREEZE button
The [II] icon appears and the screen will freeze at
the current image. Press the FREEZE button again
and the [ ] appears as the projector exits FREEZE
mode.
FREEZE
▲
OFF
FREEZE
1
MENU
NOTE
• The projector will automatically exit from FREEZE mode if either the POSITION, VOLUME, MUTE, AUTO,
BLANK ON/OFF or MENU ON/OFF feature is used, or, if there is a change in the input signal's state.
• If the projector continues projecting the same image for a long time (i.e. you forget to exit FREEZE mode),
the image might possibly remain as an afterimage. Do not leave the projector in FREEZE mode for too long.
Downloaded from ProjectorsManual.com Manuals
21
SIGNAL SEARCHING
1
STANDBY/ON
VIDEO
RGB
SEARCH
AUTO
ASPECT
BLANK
VOLUME
MAGNIFY
ON
Press the SEARCH button
When you press the SEARCH button, the projector begins
searching for input signals. If it detects an input signal, the
search will cease and the projector will project the detected
signal. If the projector is unable to find an input signal at any of
its ports, it will return to the state it was in prior to the search.
MUTE
SEARCH
OFF
FREEZE
KEYSTONE
RGB IN
COMPONENT VIDEO
VIDEO IN
S-VIDEO IN
SELECTING THE ASPECT RATIO
1
Press the ASPECT button
STANDBY/ON
VIDEO
RGB
ASPECT
ASPECT
SEARCH
AUTO
BLANK
VOLUME
MAGNIFY
ON
MUTE
RGB IN, COMPONENT VIDEO
(HDTV signals : 1125i (1035i/1080i), 750p)
4:3
16:9
VIDEO IN, S-VIDEO IN, COMPONENT VIDEO
(Non-HDTV signals : 525i, 525p,625i)
OFF
FREEZE
KEYSTONE
POSITION
MENU
4:3
ENTER
ESC
16:9
SMALL
RESET
TEMPORARILY BLANKING THE SCREEN
1
STANDBY/ON
VIDEO
ASPECT
MAGNIFY
RGB
SEARCH
AUTO
BLANK
VOLUME
ON
Press the BLANK button
The input signal screen is shut off, and a blank screen
appears. You can set the blank screen using the menu
(from the SCREEN menu, select BLANK). Press the BLANK
button again to remove the blank screen, and return to the
input signal screen.
MUTE
OFF
FREEZE
POSITION
22
KEYSTONE
BLANK
MENU
Downloaded from ProjectorsManual.com Manuals
USING THE MENU FUNCTIONS
1
Press the MENU button
2
/
Select a menu using the
buttons,
then press the
or ENTER button.
STANDBY/ON
VIDEO
ASPECT
RGB
SEARCH
AUTO
BLANK
VOLUME
MAGNIFY
ON
MUTE
MENU
The menu display appears on the screen. The
projector has the following menus: MAIN,
PICTURE-1, PICTURE-2, INPUT, SCREEN, and
OPTION. Select a menu using the
/
buttons. The
current settings of the items that can be manipulated via the
selected menu appear.
OFF
FREEZE
KEYSTONE
POSITION
MENU
The display of the selected menu appears.
[ex. Adjusting SHARPNESS]
Use the
/
buttons to select PICTURE-1, then press
the
or ENTER button.
MENU
ENTER
ESC
RESET
ENTER
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
–1
+1
–1
+1
–1
COLOR BAL R
COLOR BAL B
SHARPNESS
COLOR
TINT
: SELECT
3
Select an item using the
or ENTER button.
/
buttons, then press the
The operation display of the selected item appears. To adjust a numerical value,
press the
or ENTER button again to switch to the single menu (small display
showing only the operation display area).
[ex. Adjusting SHARPNESS]
Use the
/
buttons to select SHARPNESS, then
MENU
press the
or ENTER button.
MAIN
COLOR BAL R
ENTER
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
COLOR BAL B
SHARPNESS
COLOR
TINT
0
: SELECT
4
Press the
/
buttons to adjust the level.
Press the MENU button to hide the menu and finish your operation. Alternatively,
press the
or ESC button to return to the previous display.
[ex. Adjusting SHARPNESS]
Use the
/
buttons to adjust the SHARPNESS.
Downloaded from ProjectorsManual.com Manuals
23
MULTIFUNCTIONAL SETTINGS
This device has 6 separate menus: MAIN, PICTURE-1, PICTURE-2, INPUT,
SCREEN, OPTION. Each of these menus is operated using the same methods.
The basic operations of these menus are as follows.
Menu screen display : Press the "MENU" button.
Menu selection
: Choose a menu name using the
/
button, and press the
button or the ENTER button.
Item selection
: Choose an item using the
/
button, and press the
button or the ENTER button.
Return menu to last previous screen: Press the
button or the ESC button.
Execution of settings and/or adjustments: Operate by using the
/
button. (For further
details, read the explanation for each separate menu.)
Initialization of settings and/or adjustments: During operation, press the RESET button.
(Note that items whose functions are
performed simultaneously with the operation
of clock phase, language selection, automatic
adjustment, etc., cannot be initialized.)
End menu operations: Press the MENU button, or do not perform any operation for
several seconds.
MAIN Menu
With the MAIN menu, the seven items shown in the Table below can be
performed.
Perform each operation in accordance with the instructions in the Table.
Item
Adjust Brightness: Light
CONTRAST
Adjust Contrast: Strong
⇔
Dark
⇔
Weak
Select Aspect Ratio:
At RGB Input or Hi-Vision 1125i(1035i/1080i)/750p of COMPONENT VIDEO
Input:
4:3
⇔
16:9
At VIDEO Input, S-VIDEO Input or 525i/525p/625i of COMPONENT VIDEO Input:
4:3
⇔
16:9
⇔
SMALL
• The SMALL picture may not be displayed correctly with certain input signals.
Select Picture Position (for 16:9/SMALL Picture):
TOP
⇔
CENTER
⇔
BOTTOM
GAMMA
Select Gamma Mode:
NORMAL
⇔
CINEMA
MIRROR
Select Mirror Status:
NORMAL
⇔
H:INVERT
LANGUAGE
12
: SELECT
Description
BRIGHT
PICT.POSIT.
BRIGHT
CONTRAST
ASPECT
PICT. POSIT.
GAMMA
MIRROR
LANGUAGE
Example : MAIN Menu
(BRIGHT)
MAIN Menu
ASPECT
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
⇔
⇔
DYNAMIC
V:INVERT
⇔
H&V:INVERT
Select Menu Language:
ENGLISH
⇔
FRANÇAIS
⇔
DEUTSCH
⇔
ESPAÑOL
⇔
ITALIANO
⇔
NORSK
⇔
NEDERLANDS
⇔
日本語
⇔
POTUGUÊS
⇔
中文
⇔
Downloaded from ProjectorsManual.com Manuals
24
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
PICTURE-1 Menu
With the PICTURE-1 menu, the five items shown in the Table
below can be performed.
Perform each operation in accordance with the instructions in the
Table.
COLOR BAL R
COLOR BAL B
SHARPNESS
COLOR
TINT
12
: SELECT
Example : PICTURE-1 Menu
(COLOR BAL R)
PICTURE-1 Menu
Item
Description
COLOR BAL R
Adjust Red Color Balance: Dark
⇔
Light
COLOR BAL B
Adjust Blue Color Balance: Dark
⇔
Light
SHARPNESS
COLOR
TINT
⇔
Adjust Sharpness (for VIDEO/S-VIDEO): Clear
Soft
Adjust COLOR (for VIDEO/S-VIDEO/COMPONENT VIDEO):
Dark
⇔
Light
⇔
Adjust Tint (for VIDEO/S-VIDEO): Green
PICTURE-2 Menu
With the PICTURE-2 menu, the four items shown in the Table
below can be performed.
Perform each operation in accordance with the instructions in the
Table.
Red
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
V POSITION
H POSITION
H PHASE
H SIZE
12
: SELECT
Example : PICTURE-2 Menu
(V POSITION)
PICTURE-2 Menu
Item
Description
V POSITION
Adjust Vertical Position (for RGB): Up
H POSITION
Adjust Horizontal Position (for RGB): Left
H PHASE
H SIZE
⇔
Down
⇔
Right
Adjust Horizontal Phase (for RGB/COMPONENT VIDEO):
Right
⇔
Left
• Adjust to eliminate flicker.
Adjust Horizontal Size (for RGB): Large
⇔
Small
• If the horizontal size adjustment is excessive, the image may not be displayed
correctly. In such a case, initialize H SIZE with the RESET button.
Downloaded from ProjectorsManual.com Manuals
25
MULTIFUNCTIONAL SETTINGS (continued)
INPUT Menu
With the INPUT menu, the four items shown in the Table below can be
performed. With inputting of RGB IN signal, the horizontal and vertical
frequencies of the signal will be displayed on the initial screen of the
INPUT menu.
Perform each operation in accordance with the instructions in the Table.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
AUTO
VIDEO
HDTV
SYNC ON G
EXECUTE
: SELECT
Example : INPUT Menu
(AUTO)
INPUT Menu
Item
Description
AUTO
Auto Adjust (for RGB): Automatically adjusts H POSITION, V POSITION, H
PHASE, and H SIZE. Use this function with the maximum window size.
Auto Adjust (for VIDEO/S-VIDEO): Automatically selects the proper VIDEO
mode for the current input signal. This function is active only when the AUTO
mode is selected for the item VIDEO. Refer to the description for the item
VIDEO below.
• This function may not be available with a PAL60 signal and certain other
signals.
• The AUTO mode operation requires approximately 10 seconds.
• For COMPONENT VIDEO, the signal type is identified automatically even if
this function is inactive. For a HDTV signal, refer to the item HDTV below.
VIDEO
Select Mode of Signal Type (for VIDEO/S-VIDEO):
AUTO
⇔
NTSC
⇔
PAL
⇔
SECAM
⇔
NTSC4.43
⇔
M-PAL
⇔
N-PAL
Selecting AUTO mode activates and performs the AUTO function for VIDEO/SVIDEO. It automatically selects the proper mode from among those above.
Use this function if the image becomes unstable with VIDEO/S-VIDEO. (e.g.
The image becomes irregular, or lacks color.)
• AUTO mode may not function correctly with a PAL60 signal and certain other
signals.
• The AUTO mode operation requires approximately 10 seconds.
• For COMPONENT VIDEO, the signal type is identified automatically even if
this function is inactive. For a HDTV signal, refer to the item HDTV below.
HDTV
Select HDTV Signal Mode:
1080i
⇔
1035i
• If the selected HDTV mode is incompatible with the input signal, the picture
may be distorted.
SYNC ON G
On/Off SYNC ON G Mode:
TURN ON
⇔
TURN OFF
Selecting TURN ON turns on the SYNC ON G mode. The SYNC ON G mode
allows reception of SYNC on G.
• In the SYNC ON G mode, the picture may be distorted with certain input
signals. In such a case, remove the signal connector so that no signal is
received and turn SYNC ON G off, and then reconnect the signal.
Downloaded from ProjectorsManual.com Manuals
26
SCREEN Menu
With the SCREEN menu, the two items shown in the Table below
can be performed.
Please perform each operation in accordance with the instructions
in the Table.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
BLANK
START UP
: SELECT
Example : SCREEN Menu
(BLANK)
SCREEN Menu
Item
Description
BLANK
Selection of BLANK Screen:
.
.
⇔
.
.
⇔
.
.
The BLANK Screen may be voluntarily selected. The BLANK Screen is
displayed when the screen has been erased (i.e., made to vanish) by
manipulating the BLANK button (please refer to the “Temporarily Blanking the
Screen” section of the separate booklet, Vol. 1 (Basic)).
Option screens: Various colored non-patterned (plain) screens displayed
within the Menus.
START UP
Selection of START UP Screen:
TURN ON
⇔
TURN OFF
The START UP Screen may be voluntarily selected. The START UP Screen is
displayed when no signal has been inputted, or when spec signals are being
inputted.
TURN ON: Existing standard screens. Please make confirmation using the
actual screen(s).
TURN OFF: A non-patterned (plain) blue color screen.
• Note that if TURN OFF is selected the blank screen is displayed in blue when
there is no signal.
Downloaded from ProjectorsManual.com Manuals
27
MULTIFUNCTIONAL SETTINGS (continued)
OPTION Menu
With the OPTION menu, the five items shown in the Table below
can be performed.
Please perform each operation in accordance with the instructions
in the Table.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
VOLUME
AUTO OFF
WHISPER
LAMP TIME
FILTER TIME
12
: SELECT
Example : OPTION Menu
(VOLUME)
OPTION Menu
Item
VOLUME
Description
Adjust Volume: High
⇔
Low
AUTO OFF
Adjust AUTO OFF Time:
Long (MAX. 99 min.)
⇔
Short (Min. 1 min.)
⇔
(DISABLE: 0 min.)
The system automatically enters the standby mode if no signal is received
within the set time. This function is inactive when DISABLE (0 min.) is selected.
WHISPER
Select WHISPER Mode:
NORMAL
⇔
WHISPER
When WHISPER is selected the WHISPER mode is activated. In the WHISPER
mode, acoustic noise and screen brightness are reduced.
LAMP TIME
Refer to LAMP TIME: When set, this function displays the total time the
projector lamp has been used since new.
Reset LAMP TIME [Use this function only when the lamp has been replaced!]:
Depress the RESET button for at least 3 seconds while lamp time is being
displayed. The reset menu will then appear. After you replace the lamp with a
new lamp, select RESET on the menu with the
button.
• Do not reset the lamp time unless you have replaced the lamp. And, always
reset the lamp time when replacing the lamp. The message functions will not
operate properly if the lamp time is not reset correctly.
• Before replacing the lamp, carefully read the descriptions headed "THE
LAMP".
FILTER TIME
Refer to FILTER TIME: This function displays the total time the air-filter has
been used since new.
Reset FILTER TIME [Use this function only when the filter is cleaned or replaced!]:
Depress the RESET button for at least 3 seconds while lamp time is being
displayed. The reset menu will then appear. After you replace the filter, select
RESET on the menu with the
button.
RESET
⇔
CANCEL
• Do not reset the filter time unless you have cleaned or replaced the filter. And,
always reset the filter time when cleaning or replacing the filter. The message
functions will not operate properly if the filter time is not reset correctly.
• Before cleaning or replacing the filter, carefully read the descriptions headed "THE AIR FILTER".
Downloaded from ProjectorsManual.com Manuals
28
THE LAMP
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
Before replacing the lamp, check the serial number of the replacement lamp bulb (sold separately:
78-6969-9463-7 for MP7640i / 78-6969-9565-9 for MP7740i), then contact your local dealer.
Before replacing the lamp, turn off the power, and unplug the power cord, then wait at least
45 minutes, in order to ensure that the lamp is properly cooled. Removing the lamp bulb while
it is still hot could cause burns, or cause the lamp bulb to burst.
The LCD projector uses a glass lamp bulb. It is a mercury lamp with high
internal pressure. High-pressure mercury lamps can break with a loud
bang, or burn out, if jolted or scratched, or through wear over time. Each lamp has a
different lifetime, and some may burst or burn out soon after you start using them. In
addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing,
and for gas containing mercury to escape from the projector’s vent holes.
• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• If the replace lamp indicator (see "Related Messages" ( 34 ) and "Regarding the
indicator Lamps" ( 35 )) comes on, replace the lamp as soon as possible. Using the
lamp for long periods of time, or past the replacement date, could cause it to burst. Do
not use old (used) lamps; this is a cause of breakage.
• If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems
elsewhere besides the lamp. If this happens, contact your local dealer.
• If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make
sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.
• If the lamp should break (it will make a loud bang when it does), unplug the power cord from
the outlet, and make sure to request a replacement lamp from your local dealer. Note that
shards of glass could damage the projector’s internals, or cause injury during handling, so
please do not try to clean the projector or replace the lamp yourself.
• Obey local ordinances when disposing of used lamps. In most cases, it is possible to dispose of used
bulbs in the same manner as used glass bottles, but in some cases, bulbs are sorted separately.
• Do not use the projector with the lamp cover removed.
WARNING
Downloaded from ProjectorsManual.com Manuals
29
Replacing the lamp
All projector lamps will wear out eventually. If used for long periods of time, the image could become
darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps
early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up
the projector, the lamp needs to be replaced. (See "Related Messages" ( 34 ) and "Regarding the
Indicator Lamps" ( 35 ) for details.)
1
Turn off the projector, and unplug the
unolug the power cord.
Allow the lamp bulb to cool for at
least 45 minutes, and prepare a new
lamp.
5
Insert the new lamp, and tighten the 1
screw firmly to lock it in place
• Also steadily push the opposite side of the
screwed side of the
lamp into the unit.
2
After making sure that the projector has
cooled adequately, slowly flip over the
projector, so that the bottom is facing up
3
Unscrew the 2
screws, and
remove the
lamp cover
6
Replace the lamp
cover, and tighten
the 2 screws firmly
to lock it in place
4
Unscrew the 1 screw, and slowly pull
out the lamp by the handle
7
Slowly turn the projector so that
the top is facing up
8
Turn on the projector power, and using
the menu, reset the lamp timer
• Be careful not to touch the inside of the lamp case.
• To reset the lamp timer, from the OPTION
menu, select LAMP TIME. (See “OPTION
menu” ( 28 ) for details.)
ATTENTION • Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.
• Do not use with lamp cover removed.
• Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing
the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.
• When the lamp has been replaced after the message of "CHANGE THE LAMP ...THE POWER
WILL TURN OFF AFTER 0 hr." is displayed, or the LAMP indicator is red, complete the following
operation within 10 minutes of switching power ON.
NOTE • The LAMP indicator is also red when the lamp unit reaches high temperature.
Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power
ON again. If the LAMP indicator is still red, replace the lamp.
30
Downloaded from ProjectorsManual.com Manuals
THE AIR FILTER
Caring for the air filter
The air filter should be cleaned about every 100 hours. If the LAMP indicator and
TEMP indicator blink red simultaneously, or a message prompts you to clean the air
filter when you turn on the unit, the filter needs to be cleaned. (See "Related
Messages" ( 34 ) and "Regarding the Indicator Lamps" ( 35 ) for details.)
1
Turn off the projector, and unplug the power cord
2
Apply a vacuum cleaner to
the top of the air filter cover
to clean the air filter
Air Filter Cover
3
Turn on the projector, and use the menu to reset the filter
timer
• To reset the air filter timer, from the OPTION menu, select FILTER TIME. (See
“OPTION menu” ( 28 ) for details.)
Downloaded from ProjectorsManual.com Manuals
31
Replacing the air filter
If the soiling will not come off the air filter, or it becomes damaged, then it needs to be
replaced. Please contact your local dealer, after confirming the model of your
separately sold replacement air filter.
1
Turn off the projector, and unplug the power cord. Prepare a
new air filter (one specified for your projector)
2
Remove the air filter cover and air filter
3
Insert the new filter, and replace the
filter cover
4
Turn on the projector power, and using the menu, reset the
filter timer
• To reset the filter timer, from the OPTION menu, select FILTER TIME. (See
“OPTION menu” ( 28 ) for details.)
ATTENTION • Make sure to turn off the power and unplug the power cord before caring for the
unit. Please carefully read "Product Safety Instruction", in order to care for your projector correctly.
• Do not use with air filter cover removed.
• If the air filter becomes clogged by dust or the like, internal temperature rises and could cause
malfunction. The power is automatically turned off in order to prevent the unit from overheating
internally.
32
Downloaded from ProjectorsManual.com Manuals
OTHER CARE
Caring for the inside of the projector :
In order to ensure the safe use of your projector, please have it cleaned and inspected by
your local dealer about once every 2 years. Never try to care for the inside of the unit
yourself. Doing so is dangerous.
Caring for the lens :
Lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the
lens directly with your hand.
Caring for the cabinet and remote control transmitter :
Wipe lightly with gauze or a soft cloth. If soiling is severe, dip a soft cloth in water or a
neutral cleanser diluted in water, and wipe lightly after wringing well. Then, wipe lightly
with a soft, dry cloth.
ATTENTION • Make sure to turn off the power and unplug the power cord before caring for
the unit. Please carefully read "Product Safety Guide" in this manual, in order to care for your
projector correctly.
• Do not use cleaners or chemicals other than those listed above, including benzene and paint
thinner.
• Do not use aerosols or sprays.
• Do not polish or wipe with hard objects.
Downloaded from ProjectorsManual.com Manuals
33
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED
Related Messages
When the unit's power is ON, messages such as those shown below may be displayed. When
any such message is displayed on the screen, please respond as described below.
Message
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
(Note 1)
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER ** hr.
(Note 1)
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER 0 hr.
CLEAN THE AIR FILTER
AFTER CLEANING AIR FILTER,
RESET THE FILTER TIMER.
NO INPUT IS DETECTED
ON ***
Description
Lamp usage time is approaching 2,000 hours. (Note 2)
Preparation of a new lamp, and an early lamp change, is
recommended. After you have changed the lamp, please be
sure to reset the lamp timer.
Lamp usage time is approaching 2,000 hours. A lamp change
within ** hours is recommended. (Note 2)
When lamp usage reaches 2,000 hours, the power will
automatically be turned OFF. Please change the lamp by
referring to “THE LAMP”. 29
After you have
changed the lamp, please be sure to reset the lamp
timer. 28
As lamp use has reached 2,000 hours, the power will soon be
automatically turned OFF. (Note 2)
Please immediately turn the power OFF, and follow the
instructions in the “THE LAMP”, 29
After you have changed the lamp, please be sure to reset the
lamp timer. 28
A note of precaution when cleaning the air filter.
After cleaning the filter, operate FILTER TIME of the OPTION
Menu, and perform reset of the filter timer. 28
There is no input signal.
Please confirm the signal input connection, and the status of the
signal source.
The horizontal or vertical wavelength of the inputted signal is
SYNC IS OUT OF RANGE
outside of the response parameters of this unit. Please confirm
fV
fH
ON ***
*****kHz
*****Hz the specs for this unit or the signal source specs.
The internal portion temperature is rising. Please turn the power
OFF, and allow the unit to cool down for approximately 20
minutes. After having confirmed the following items, then please
CHECK THE AIR FLOW
resent the power to ON.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
NOTES
Note 1: Although this message will be automatically disappeared after around 3 minutes, it will be
reappeared every time the power is turned ON.
Note 2: Lamps have a finite product life. Lamps are characterized by the fact that, after long hours of
usage, a lamp will no longer light up, or the lamp will break or burst, etc. This unit is equipped
with an automatic shut-down function, such that the power will automatically be turned OFF
when lamp usage time has reached 2,000 hours. Please be aware, however, that among lamp
types, there are major differences in product lifetimes; a lamp may thus fail to light even prior
to the functioning of the automatic shut-down function of this unit.
34
Downloaded from ProjectorsManual.com Manuals
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued)
Regarding the Indicator Lamps
Lighting and flashing of the POWER indicator, the LAMP indicator, and the
TEMP indicator have the meanings as described in the Table below.
Please respond in accordance with the instructions within the Table.
POWER
indicator
LAMP
indicator
TEMP
indicator
The orange Turned OFF Turned OFF
lamp is lighted (Not lighted) (Not lighted)
Description
The STANDBY mode is set
Flashing of the green lamp
Turned OFF
Turned OFF
The unit is warming up. Please wait.
The green lamp is lighted
Turned OFF
Turned OFF
The unit is in an ON state. Ordinary operations may be performed.
Flashing of the orange lamp
Turned OFF
Turned OFF
Blinking of the
red lamp
-
-
The red lamp
Turned
OFF
The unit is cooling down. Please wait.
The unit is cooling down. Please wait.
A certain error has been detected. Wait until the POWER indicator lamp has finished
flashing, and then perform the proper response measure using the item descriptions
below as reference.
The lamp does not light.
There is a possibility that the interior portion has become heated. Turn the power OFF and wait
approximately 20 minutes. After the main unit has cooled down, please confirm whether or not
there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or
not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance,
turn the power ON again; if the same display is displayed, then please change the lamp.
The red lamp
is lighted, or
blinks
The red lamp
is lighted, or
blinks
The red lamp
is lighted, or
blinks
The red lamp is
lighted, or
blinks
The green lamp
is lighted
The green
lamp is lighted
is lighted
Blinking of the
red lamp
Turned
OFF
Either there is no lamp and/or lamp cover, or either of these has not been properly fixed
(attached). Turn the power OFF and wait approximately 45 minutes. After the main unit has
sufficiently cooled down, please make confirmation of the attachment state of the lamp and
lamp cover. After performing any needed maintenance, turn the power ON again; if the same
display is displayed, then please contact a sales store or a service company.
The cooling fan is not operating. Turn the power OFF and wait approximately 20 minutes. After the
main unit has cooled down, please make confirmation that no foreign matter has become caught in
the fan, etc. After performing any needed maintenance, turn the power ON again; if the same display
red lamp
is displayed, then please contact a sales store or a service company.
There is a possibility that the interior portion has become heated. Turn the power OFF and wait
approximately 20 minutes. After the main unit has cooled down, please confirm whether or not
Turned The red lamp is there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or
not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance,
lighted
OFF
turn the power ON again; if the same display is displayed, then please contact a sales store or a
service company.
There is a possibility that the interior portion has become overcooled. Please use the unit within
Alternative blinking
the usage temperature parameters (0°C to 35°C). After performing any needed maintenance,
turn the power ON again; if the same display is displayed, then please contact a sales store or a
with the red lamp
service company.
Turned
OFF
Blinking of the
Simultaneous blinking
with the red lamp
This is a notification that it is time to clean the filter.
After cleaning the filter, operate the FILTER TIME portion of the OPTION Menu, and perform
reset of the FILTER TIME.
NOTE
When the interior portion has become overheated, for safety purposes, the power source is automatically turned OFF, and the
indicator lamps may also be turned OFF. Press the “○” (power OFF) side of the main power switch, and wait for approximately 20
minutes. Please then use the unit only after having first confirmed that the unit has sufficiently cooled down.
Downloaded from ProjectorsManual.com Manuals
35
Phenomena That May Easily Be Mistaken for Machine Defects
Before requesting repair, check in accordance with the following chart.
If the situation cannot be corrected, then contact your dealer.
Phenomenon
Power does not
come ON
No sound or
pictures are
outputted
Pictures are
displayed, but no
sounds are heard
Sounds are
heard, but no
pictures are
displayed
Colors have a fadedout appearance
Color tone is poor
Pictures appear
dark
Pictures appear
blurry
Cases not involving a machine defect
Items to be confirmed
Reference
Page(s)
The main power source is not ON.
Turn on the main power.
The electrical power cord is not plugged in.
The input changeover settings
are mismatched.
Correctly connect the power cord.
Be sure to press the “O” (power OFF) side
of the main power switch, and leave this OFF
for approximately 20 minutes. After the unit 14
has sufficiently cooled down, turn ON the
power source.
Select the input signal, and
15
correct the settings.
No signal is being inputted.
Correctly connect the connection cord.
10, 11
The electrical wiring to this unit
is not correctly connected.
Correctly connect the connection cord.
10, 11
The volume setting has been set at (or
adjusted to) an extremely low level.
Adjust the VOLUME setting to a higher level.
17
The MUTE mode is the current setting.
Press the MUTE button to release
17
(change) the MUTE mode setting.
The electrical wiring to this unit
is not correctly connected.
Correctly connect the connection cord.
10, 11
The brightness setting has been set at
(or adjusted to) an extremely low level.
Adjust the BRIGHT setting to a
brighter level.
24
The Slide lens door has not been removed.
Remove the Slide lens door.
14
Color depth setting or color tone setting
Perform picture adjustments by changing the
COLOR BAL R, the COLOR BAL B, and/or the 25
TINT settings, etc.
The brightness setting and/or contrast
setting has not been properly adjusted.
Perform picture adjustments by changing the
24
BRIGHT and/or CONTRAST settings, etc.
The WHISPER mode is the current
setting.
Change (by releasing) from the
28
WHISPER mode.
Lamp is approaching the end of its
product lifetime.
Exchange the old lamp with a new
24, 25
lamp.
Either the FOCUS setting or the H
PHASE is not properly adjusted.
Adjust the FOCUS and H PHASE settings.
The main power source has been
interrupted during operation, such as by
a power outage (blackout), etc.
3, 14
15, 25
NOTE
Although bright spots or dark spots may appear on the screen, this is a unique characteristic of
liquid crystal displays, and such do not constitute or imply a machine defect.
36
Downloaded from ProjectorsManual.com Manuals
SPECIFICATIONS
NOTE • This specifications are subject to change without notice.
Item
Specification
Product name
Liquid
crystal
panel
Liquid crystal projector
Panel size
1.8 cm (0.7 type)
Drive system
TFT active matrix
Pixels
MP7640i:480,000 pixels (800 horizontal x600 vertical)
MP7740i:786,432 pixels (1024 horizontal x 768 vertical)
Lens
Zoom lens F=2.0 ~ 2.3 f=18 ~ 21 mm
Lamp
150 W UHB
Speaker
1.0W
Power supply
AC100 ~ 120V, 2.7A / AC220 ~ 240V, 1.3A
Power consumption
240W
Temperature range
0 ~ 35°C (Operating)
Size
289 (W) x 84 (H) x 215 (D) mm
Weight (mass)
2.4 kg
Ports
RGB Port
RGB IN ..........................1
VIDEO Ports
VIDEO IN ........................1
S-VIDEO IN ....................1
COMPONENT VIDEO
(Y, CB/PB,CR/PR) ......1
AUDIO Ports
AUDIO IN(R, L) ..............1
AUDIO IN........................1
CONTROL Port
CONTROL ......................1
215
Dimension Diagram
289
60
84
52.5
Downloaded from ProjectorsManual.com Manuals
74.5
Unit : mm
37
ACCESSORIES
Acccessories..................................................................................Part Number
UHB lamp, 150W (MP7640i) ..........................................................78-6969-9463-7
UHB lamp, 150W (MP7740i) ..........................................................78-6969-9565-9
Air Filter ..........................................................................................78-8118-8908-4
Power cord (US) .............................................................................78-8118-8102-4
Power cord (UK) .............................................................................78-8118-8101-6
Power cord (Europe) .......................................................................78-8118-8103-2
VGA cable ......................................................................................78-8118-8708-8
RCA component cable ....................................................................78-8118-8843-3
RCA audio/video cable....................................................................78-8118-3234-0
Stereo mini-cable ............................................................................78-8118-8846-6
Remote control ................................................................................78-8118-9121-3
Soft carry case ..............................................................................78-6969-9203-7
Not Included with Basic Packet....................................................Part Number
Ceiling mount ................................................................................78-6969-9206-0
Adjustable height suspension ........................................................78-6969-8312-7
Shipping case ................................................................................78-6969-9204-5
S-Video cable ................................................................................78-8118-3238-1
RS-232C control cable ..................................................................78-8118-3312-4
Mac adapter ....................................................................................78-8118-3308-2
Deluxe Mouse Emulation Kit .......................................................... 78-6969-9233-4
How to Order
Please order these parts through your dealer, or contact 3M Customer Service at the
following number :
In U.S. or Canada : 1-800-328-1371
In other locations,contact your local 3M sales office.
38
Downloaded from ProjectorsManual.com Manuals
Intended Use
Before operating this machine, please read this entire manual thoroughly. The 3MTM Multimedia Projectors are designed, built, and tested for use indoors,
using 3M lamps, 3M ceiling mount hardware, and nominal local voltages.
The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could damage the projector peripheral equipment
and/or create a potentially unsafe operating condition.
3M Multimedia projectors and Wall Display Systems are designed to operate in a normal office environment.
• 16˚ to 29˚C (60˚ to 85˚ F)
• 10- 80 %RH (without condensation)
• 0- 1828 m (0-6000 feet) above sea level
The ambient operating environment should be free of airborne smoke, grease, oil and other contaminates that can affect the operation or performance of the
projector.
Use of this product in adverse conditions will void the product warranty.
Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we're the only
transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call
us toll-free in the continental United States and Canada, 24 hours a day, or visit our Internet Website.
3M Austin Center
Building A145-5N-01
6801 River Place Blvd.
Austin, TX 78726-9000
3M Canada
P.O. Box 5757
London, Ontario
N6A 4T1
3M Mexico, S.A. de C.V.
Apartado Postal 14-139
Mexico, D.F. 07000
Mexico
3M Europe
Boulevard de l'Oise
95006 Cerge Pontoise Cedex
France
DN00381 (QR56101_OG_ENG)
Downloaded
from ProjectorsManual.com Manuals
Litho in Japan
© 3M 2002
78-6970-9166-4 Rev. A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement