Sharp | AL-1000 Series | Specifications | Sharp AL-1000 Series Specifications

FOR YOUR PROTECTION...
To aid in reporting this compact copier in case of loss or theft, please record below the model
number and serial number located on the back of the unit. We also suggest you record all the
information listed and retain for future reference.
MODEL NUMBER
SERIAL NUMBER
DATE OF PURCHASE
Dealer
Address
City
State
Zip
Telephone
Service Station
Address
City
State
Zip
Telephone
For location of the nearest Sharp Authorized Service, or to
obtain product literature, accessories, supplies or customer
assistance,
please call
1 - 800 - BE-SHARP
For product information or customer assistance, please visit
http://www.sharp-usa.com on the World Wide Web or call
1-800-BE-SHARP.
CONTENTS
1
GETTING STARTED
INTRODUCTION
CAUTIONS
3
3
MAIN FEATURES
PART NAMES
4
6
OPERATION PANEL
2
7
INSTALLATION
COPIER INSTALLATION
8
CAUTIONS ON HANDLING
9
CHECKING PACKED COMPONENTS AND
ACCESSORIES 10
UNPACKING 10
REMOVING PROTECTIVE PACKING MATERIALS
INSTALLING THE TD CARTRIDGE
11
LOADING COPY PAPER (installing the paper tray)
POWER TO COPIER
POWER ON
16
16
MAKING COPIES
PAPER
17
NORMAL COPYING
18
– Setting a large original
19
EXPOSURE ADJUSTMENT/PHOTO COPYING
REDUCTION/ENLARGEMENT/ZOOM
BYPASS FEED (special paper)
TWO-SIDED COPYING
4
13
15
– Initial settings of operation panel
3
11
20
20
21
22
SPECIAL FUNCTIONS
DESCRIPTION OF SPECIAL FUNCTIONS
TONER SAVE MODE
23
23
USER PROGRAMS
(power save modes, auto clear time) 24
– Setting the power save modes and auto clear time
24
1
CONTENTS
5
SUPPLIES AND USER MAINTENANCE
TD CARTRIDGE REPLACEMENT
26
DRUM CARTRIDGE REPLACEMENT
USER MAINTENANCE
– Cabinet
28
28
– Original table and original cover
– Transfer charger
28
29
– When copier is not in use
– Copier lens cleaning
6
27
29
30
COPIER TROUBLE?
MISFEED REMOVAL
31
– Misfeed in the paper feed area
– Misfeed in the fusing area
32
– Misfeed in the transport area
TROUBLESHOOTING
34
STATUS INDICATORS
35
31
33
DISPLAYING TOTAL NUMBER OF COPIES
AUTOMATIC EXPOSURE ADJUSTMENT
7
35
36
APPENDIX
SPECIFICATIONS
37
OPTION AND SUPPLY PART NUMBERS AND STORAGE
MOVING INSTRUCTIONS
INDEX
2
39
38
1
GETTING STARTED
This chapter provides basic information for using the copier.
1
INTRODUCTION
Getting Started
This copier has been designed to provide intuitive operating ease while requiring a minimum
amount of space. To get full use of all copier features, be sure to familiarize yourself with this
manual and the copier.
For quick reference during copier use, keep this manual in a handy location.
Conventions used in this manual
In this manual, the following icons are used to provide the user with information pertinent to
the use of the copier.
Warns the user that injury to the user or damage to the copier may result if
the contents of the warning are not properly followed.
Cautions the user that damage to the copier or one of its components may
result if the contents of the caution are not properly followed.
Notes provide information relevant to the copier regarding specifications,
functions, performance, operation and such, that may be useful to the user.
Indicates a letter displayed in the display.
CAUTIONS
Follow the cautions below when using this copier.
●
Place the copier on a firm, level surface.
●
Do not install the copier in a humid or dusty location.
●
When the copier is not used for long time, for example for consecutive
holidays, turn the power switch off and remove the power cord from the
outlet.
●
The fusing area is hot. Exercise care in this area when removing misfed
paper.
When moving the copier, be sure to turn the power switch off and remove
the power cord from the outlet.
● Do not look directly at the light source. Doing so may damage your eyes.
●
●
Do not cover the copier with a dust cover, cloth or plastic film while the
power is on. Doing so may prevent heat radiation, damaging the copier.
3
CAUTIONS
SAFETY PRECAUTIONS
This Digital Copier is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of
the CDRH standards. This means that the copier does not produce hazardous laser
radiation. For your safety, observe the precautions below.
● Do not remove the cabinet, operation panel or any other covers.
● The copier's exterior covers contain several safety interlock switches. Do not bypass
any safety interlock by inserting wedges or other items into switch slots.
1
Getting Started
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
MAIN FEATURES
q High-speed laser copying
●
Since warm-up time is zero, copying can be started immediately after the power switch
is turned on.
●
First-copy time is only 9.6 seconds (normal mode).
●
Copying speed is 10 copies/min., which adapts to business use, allowing improvement
of working efficiency.
w High-quality digital image
●
High-quality image copying at 600 dpi can be performed.
●
In addition to the automatic exposure mode, the manual exposure can be adjusted in
five steps.
●
The photo mode copying function allows clear copying of delicate halftone original
images such as monochrome photos and color photos.
e Substantial copying functions
●
Zoom copying from 50% to 200% in 1% increments can be performed.
●
Continuous copying of maximum 99 sheets can also be performed.
●
Toner save mode reduces toner consumption by approximately 10%.
●
User programs allow setting/modification of functions for customer's needs.
r Scan once/ Print many (AL-1010 only)
●
4
The AL-1010 is equipped with a 1-page memory buffer. This Memory allows the AL1010 to scan an original 1 time only and make up to 99 copies. This feature allows for
improved workflow, reduced operating noise from the copier and reduced wear and
tear on the scanning mechanism. This feature provides for a higher reliability.
MAIN FEATURES
t Printer feature
●
This copier can be used as a laser printer by installing an optional printer upgrade kit.
y Environmentally friendly design
●
Paper output tray is housed in the copier for space saving.
●
Preheat mode and auto power shut-off mode are provided to reduce power consumption
in standby mode.
1
Getting Started
This copier does not have an internal calendar or clock.
This copier will not be affected by the year 2000.
5
PART NAMES
Original table
Original cover
1
Getting Started
Side cover
Operation
panel
Manual bypass
Paper tray
Paper guides
Front cover
Side cover
open button
Cover for optional
printer interface
Handle
Paper output
tray
Paper output tray
extension
Power cord socket
Power switch
TD cartridge lock release
button
TD cartridge
Drum cartridge handle
Transfer charger
Paper feed roller
Fusing unit
release lever
6
Drum cartridge
Charger cleaner
Handle
OPERATION PANEL
q
w
e
r
y
i
u
o
1
MAX.
51/2 x 81/2 81/2 x11
100%
81/2 x14 81/2 x 11
81/2 x11 51/2 x 81/2
MIN.
ZOOM
!0
q Exposure mode selector key and
indicators
Use to sequentially select the exposure
modes: AUTO, MANUAL or PHOTO.
Selected mode is shown by a lit indicator.
(p. 20)
w Light and dark keys and exposure
indicators
Use to adjust the MANUAL or PHOTO
exposure level. Selected exposure level
is shown by a lit indicator. (p.20)
Use to start and terminate user program
setting. (p. 24)
e Alarm indicators
: Drum replacement required
indicator (p. 27)
: Misfeed indicator (p. 31)
: TD cartridge replacement required
indicator (p. 26)
r Copy ratio selector key and copy ratio
indicators
Use to sequentially select preset
reduction/enlargement copy ratios.
Selected copy ratio is shown by a lit
indicator. (p. 20)
t Zoom indicator (p. 20)
y Copy ratio display (%) key (p. 20)
u Display
Displays the specified copy quantity, zoom
copy ratio, user program code, and error
code.
Getting Started
200%
129%
100%
78%
64%
50%
t
!1
!2
!3
i ON LINE indicator
Lights up when the machine is used as a
printer. To use this machine as a printer,
an optional printer upgrade kit is needed.
Lit: Indicates the machine is ready for
printing or data is being received or
printed.
o Power save indicator
Lights up when the copier is in a power
save mode. (p. 23, 24)
!0 Zoom keys
Use to select any reduction or enlargement copy ratio from 50 to 200% in 1%
increments. (p. 20)
!1 Copy quantity keys
● Use to select the desired copy quantity
(1 to 99). (p. 19)
● Use to make user program entries.
(p. 24)
!2 Clear key
● Press to clear the display, or press
during a copy run to terminate copying.
(p. 18)
● Press and hold down during standby to
display the total number of copies made
to date. (p. 35)
!3 Print key and ready indicator
● Copying is possible when the indicator
is on.
● Use to set a user program.
7
2
INSTALLATION
Follow the installation procedure below to use the copier properly.
COPIER INSTALLATION
2
Improper installation may damage the copier. Please note the following during initial installation
and whenever the copier is moved.
Installation
If the copier is moved from a cool place to a warm place, condensation may
form inside the copier. Operation in this condition will cause poor copy quality
and malfunctions. Leave the copier at room temperature for at least 2 hours
before use.
Do not install your copier in areas that are:
8
●
damp, humid, or very dusty
●
exposed to direct sunlight
●
poorly ventilated
●
subject to extreme temperature or humidity
changes, e.g., near an air conditioner or heater.
COPIER INSTALLATION
Be sure to allow the required space
around the machine for servicing and
proper ventilation.
4"
(10 cm)
8" (20 cm)
8" (20 cm)
4"
(10 cm)
A small amount of ozone is produced within the copier during operation. The emission
level is insufficient to cause any health hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3)
calculated as an 8 hr. time-weighted average concentration.
However, since the small amount that is emitted may have an objectionable odor, it is
advisable to place the copier in a ventilated area.
2
Installation
CAUTIONS ON HANDLING
Be careful in handling the copier as follows to maintain the performance of this copier.
Do not drop the copier, subject it to shock
or strike it against any object.
Do not expose the drum cartridge to direct
sunlight.
Doing so will damage the surface (green portion)
of the drum cartridge, causing smudges on copies.
Store spare supplies such as drum cartridges and TD cartridges in a dark place
without removing from the package before use.
If they are exposed to direct sunlight, smudges on copies may result.
Do not touch the surface (green portion) of the drum cartridge.
Doing so will damage the surface of the cartridge, causing smudges on copies.
9
CHECKING PACKED COMPONENTS AND
ACCESSORIES
Open the carton and check if the following components and accessories are included.
Power cord
2
Installation
Operation manual
TD cartridge
Copier
Drum cartridge
(installed in copier)
●
If anything is not included or is damaged, contact your Sharp dealer.
●
Save the carton and packing materials. These can be re-used for transporting
the machine, should it be necessary.
UNPACKING
Be sure to hold the handles on both sides of the copier to unpack the copier and carry it to the
installation location.
10
REMOVING PROTECTIVE PACKING MATERIALS
Remove pieces of tape , , , , and
and protective cover
the original cover and remove protective materials
and .
1
c
g
. Then open
h
a
e
f
2
d
Installation
b
2
Use a coin (or suitable object) to remove the screw.
Store the screw in the paper tray because it will be used if the copier has to be
moved. (p. 14)
INSTALLING THE TD CARTRIDGE
1
Open the side cover while pressing the side cover open button.
11
INSTALLING THE TD CARTRIDGE
2
Remove the CAUTION tape from the front cover and remove the two protective pins
from the fusing unit by pulling the strings upward one at a time.
2
Protective pins
Installation
CAUTION tape
3
Push gently on both sides of the front cover to open the cover.
4
Remove the TD cartridge from the bag. Remove the protective paper. Hold the
cartridge on both sides and shake it horizontally four or five times.
4 or 5 times
5
12
Hold the tab of the protective cover and pull the tab to your side to remove the cover.
INSTALLING THE TD CARTRIDGE
6
Gently insert the TD cartridge until it locks in place.
7
Close the front cover and then the side cover by pressing the round projections near
the side cover open button.
2
Installation
When closing the covers, be sure to close the front cover securely and then
close the side cover. If the covers are closed in the wrong order, the covers
may be damaged.
LOADING COPY PAPER (installing the paper
tray)
1
Raise the handle of the paper tray and pull the paper tray out until it stops.
13
LOADING COPY PAPER
2
Remove the pressure plate lock. Rotate the pressure plate lock in the direction of
the arrow to remove it while pressing down the pressure plate of the paper tray.
3
Store the pressure plate lock which has been removed in step 2 and the screw
which has been removed when unpacking (see page 11, step 2 of REMOVING
PROTECTIVE PACKING MATERIALS) in the front of the paper tray. To store the
pressure plate lock, rotate the lock to fix it on the relevant location.
2
Installation
Pressure plate lock
4
Screw
Adjust the paper guides on the paper tray to the copy paper width and length.
Squeeze the lever of paper guide
and slide the guide to match with the width of
the paper.
Move paper guide
to the appropriate slot as marked on the tray.
Paper guide B
5
Fan the copy paper and insert it into the tray. Make sure the edges go under the
corner hooks.
Do not load paper above the maximum height line (
will cause a paper misfeed.
14
Paper guide A
). Exceeding the line
LOADING COPY PAPER
6
Gently push the paper tray back into the copier.
After loading copy paper, to cancel the blinking "P" without restarting copying,
press the clear ( ) key. The "P" in the display will go out and the ready (
)
indicator will light up.
2
Installation
POWER TO COPIER
1
Ensure that the power switch of the copier is in the OFF position. Insert the attached
power cord into the power cord socket at the rear of the copier.
If you use the copier in a country other than the country where the copier was
purchased, you will need to make sure that your local power supply is
compatible with your model. If you plug the copier into an incompatible power
supply, irreparable damage to the copier will result.
2
Plug the other end of the power cord into the nearest outlet.
Only insert the power cord into a properly grounded wall socket.
Do not use extension cords or power strips.
15
POWER ON
Turn the power switch on the left side of the copier to the "ON" position. The ready (
)
indicator will light up and other indicators which show the initial settings of the operation
panel will also light up to indicate the ready condition. For the initial settings, see the "Initial
settings of operation panel" described below.
●
The copier will enter a power save mode once the set time has elapsed
without any copier operation after the last copy of a run is made or power is
turned on.
The settings of the power save modes can be modified. See page 24, USER
PROGRAMS.
●
The copier will return to the initial settings a preset amount of time after the
last copy is made. The preset amount of time (auto clear time) can be
changed. See page 24, USER PROGRAMS.
2
Installation
Initial settings of operation panel
The copier assumes the initial settings when the copier is turned on or a preset time (auto
clear time) elapses after the last copy is made. The initial settings of the operation panel are
shown below.
200%
129%
100%
78%
64%
50%
MAX.
51/2 x 81/2 81/2 x11
100%
81/2 x14 81/2 x 11
81/2 x11 51/2 x 81/2
MIN.
ZOOM
"0" is displayed in the
display.
16
3
MAKING COPIES
This chapter describes basic copying functions and some other copying functions using the
manual bypass.
PAPER
For best results, use only paper recommended by SHARP.
Type of paper
feeding
Paper tray
Size
3
Weight
Standard paper
Letter (8-1/2" x 11")
15 lbs. to 21 lbs.
Legal (8-1/2" x 14")
Invoice (5-1/2" x 8-1/2")
A4 (210mm x 297mm)
B5 (182mm x 257mm)
Standard paper and
thick paper
Letter (8-1/2" x 11")
14 lbs. to 34.5
Legal (8-1/2" x 14")
lbs.**
Invoice (5-1/2" x 8-1/2")
A4 (210mm x 297mm)
B5 (182mm x 257mm)
Special
media
Transparency
film
Letter (8-1/2" x 11")
A4 (210mm x 297mm)
Envelope*
Commercial 10
(4-1/8" x 9-1/2")
Monarch
(3-7/8" x 7-1/2")
International DL
(110mm x 279.4mm)
International C5
(162mm x 229mm)
Making copies
Manual bypass
Type of media
* Do not use envelopes that have metal clasps, plastic snappers, string closures, windows,
linings, self-adhesive, patches or synthetic materials. These will cause physical damage
to the copier.
** For paper weighing from 28 to 34.5 lbs., 8-1/2" x 11" is the maximum size that can be fed
through the manual bypass.
●
Special papers such as transparency film and labels must be fed one sheet at a time
through the manual bypass.
17
NORMAL COPYING
3
Ensure that paper of the desired size is set in the paper tray. See page 13, LOADING
COPY PAPER. When copying onto 8-1/2" x 11" paper or a larger size, pull out the
paper output tray extension.
2
Turn the power switch on.
3
Open the original cover.
4
Place the original face down on the original table. Align it with the original scale and
the centering ( ) mark.
Making copies
1
Original scale
mark
5
Gently close the original cover. When copying a book or an original which has been
folded or a crumpled original, press down the original cover lightly. If the original
cover is not securely closed, the copies may be striped or blurred.
A book, an original which has been
folded, a crumpled original
18
NORMAL COPYING
6
Set the number of copies using the two copy quantity (
●
●
) keys.
Press the clear ( ) key to clear an entry if a mistake is made.
A single copy can be made with the initial setting, i.e., when “0” is displayed.
●
Press the right copy quantity key to set the unit
digit from 0 to 9. This key will not change the
tens digit.
●
Press the left copy quantity key to set the tens
digit from 1 to 9.
ZOOM
Tens digit
7
,
Unit digit
Press the print (
3
) key.
To display the number of copies made in a continuous run, press the left
copy quantity key.
●
To stop copying in the middle of a run, press the clear (
stop and the number in the display will be reset to “0”.
Making copies
●
) key. Copying will
Setting a large original
The original cover can be removed to allow copying of bulky objects.
Simply lift the original cover straight up.
1
2
To reattach the original cover, reverse the above procedure.
19
EXPOSURE ADJUSTMENT/PHOTO COPYING
Copy density adjustment is not required for most originals in the automatic exposure mode.
To adjust the copy density manually or to copy photographs, the exposure level can be adjusted
in five steps manually.
1
Set the original and check the copy paper size.
2
Press the exposure mode selector key to select the manual (
( )mode.
3
Use the light ( ) and dark ( ) keys to adjust the exposure level.
If exposure level 2 is selected, the two left-handmost indicators for that level will
light up simultaneously. Also, if level 4 is selected, the two right-handmost indicators
for that level will light up simultaneously.
4
Set the number of copies using the copy quantity (
(
) key.
) mode or photo
3
Making copies
,
) keys and press the print
REDUCTION/ENLARGEMENT/ZOOM
Three preset reduction ratios and two enlargement ratios can be selected. The zoom function
enables copy ratio selection from 50% to 200% in 1% increments.
20
1
Set the original and check the copy paper size.
2
Use the copy ratio selector key and/or zoom (
copy ratio.
,
) keys to select the desired
●
To verify a zoom setting without changing the zoom ratio, press and hold
down the copy ratio display (%) key. When the key is released, the display
will return to the copy quantity display.
●
To reset the ratio to 100%, press the copy ratio selector key repeatedly until
the 100% indicator lights up.
REDUCTION/ENLARGEMENT/ZOOM
To select a preset copy ratio:
Preset reduction and enlargement
ratios are: 50%, 64%, 78%, 129%, and
200%
To select a zoom ratio:
When a zoom (
or
) key is pressed,
the ZOOM indicator will light up and the
zoom ratio will be displayed in the display.
To decrease or increase the zoom ratio rapidly, press and hold down the
or
key. However the value will stop at the preset reduction or enlargement
ratios. To move beyond these ratios, release the key and then press and hold
it down again.
200%
129%
100%
78%
64%
50%
100%
81/2 x14 81/2 x 11
81/2 x11 51/2 x 81/2
MIN.
MAX.
51/2 x 81/2 81/2 x11
100%
81/2 x14 81/2 x 11
81/2 x11 51/2 x 81/2
MIN.
Set the number of copies using the copy quantity (
(
) key.
3
ZOOM
,
Making copies
3
MAX.
51/2 x 81/2 81/2 x11
) keys and press the print
BYPASS FEED (special paper)
The single-sheet manual bypass can be used to feed standard paper, transparency film,
labels, and other special purpose papers measuring from 3-1/2" x 5-1/2" to 8-1/2" x 14" and
in the weight range of 14 to 34.5 lbs. (For paper weighing from 28 to 34.5 lbs., 8-1/2" x 11" is
the maximum size.)
1
Place the original face down on the original table. Align it with the original scale and
close the original cover.
The original image must be smaller than the paper or media for copying.
If the original image is bigger than the paper or media, this may cause
smudges on the edges of the copies.
2
Set the paper guides to the copy paper width. Insert a single sheet of copy paper
(print face down) into the feed slot of the manual bypass.
Copying will begin automatically.
●
●
Paper must be fed narrow side into the feed slot.
When copying onto transparency film, remove each copy promptly. Do not
let copies stack up.
Print face
21
TWO-SIDED COPYING
Two-sided copying can be made on this copier using the manual bypass.
Example: The following two originals will be copied onto two sides of copy paper.
Face up or face down
Face up
First original
3
Face down
Second original
Place the first original on the original table and make a copy.
The first copy can be made using either the paper tray or the manual bypass.
2
Replace the first original with the second original on the original table and close the
original cover. Make sure that the first and second originals are oriented in the same
way on the original table.
3
For tablet binding, turn the first copy over left to right as shown below. For booklet
binding, turn the first copy over top to bottom (not shown). Feed the first copy into
the manual bypass.
Copying will begin automatically.
Making copies
1
22
4
SPECIAL FUNCTIONS
DESCRIPTION OF SPECIAL FUNCTIONS
This chapter describes the special functions of this copier. Use these functions as needed.
Toner save mode (page 23)
Reduces toner consumption by approximately 10%.
Power save modes (page 24)
The copier has two power save modes of operation: preheat mode and auto power shut-off
mode.
Preheat mode
When the copier enters the preheat mode, the power save ( ) indicator will light up and
other indicators will remain on or off as before. In this condition, the fuser in the copier is
maintained at a lower heat level, thereby saving power. To copy from the preheat mode,
make desired copier selections and press the print (
) key using the normal copying
procedure.
●
Auto power shut-off mode
When the copier enters the auto power shut-off mode, the power save ( ) indicator will
light up and other indicators will go out. The auto power shut-off mode saves more power
than the preheat mode but requires a longer time before starting copying. To copy from the
auto power shut-off mode, press the print (
) key. Then make desired copier selections
and press the print (
) key using the normal copying procedure.
4
Special functions
●
Auto clear (page 24)
The copier returns to the initial settings a preset amount of time after the last copy is made.
This preset amount of time (auto clear time) can be changed.
TONER SAVE MODE
1
Press the exposure mode selector key to select the manual (
) mode.
23
TONER SAVE MODE
2
Press and hold down the exposure mode selector key for approximately 5 seconds.
The manual (
) indicator will go out and the photo ( ) indicator will begin to
blink. The exposure indicator marked “5” will light up, indicating the standard toner
mode is active.
3
To enter the toner save mode, press the light ( ) key.
The exposure indicator marked “1” will light up, indicating the toner save mode is
selected.
4
Press the exposure mode selector key twice. The photo ( ) indicator will stop
blinking and the AUTO indicator will light up steadily. The toner save mode is now
active.
4
Special functions
To return to the standard mode, repeat the procedure but use the dark (
key to select exposure level “5” in step 3.
)
USER PROGRAMS
(power save modes, auto clear time)
The user programs allow the parameters of certain functions to be set, changed, or canceled
as desired.
Setting the power save modes and auto clear time
24
1
Press and hold down the light ( ) and dark ( ) keys simultaneously for more
than 5 seconds until all the alarm indicators ( , , ) blink and “– –” appears in
the display.
2
Use the left copy quantity ( ) key to select a user program number (1: auto clear
time, 2: preheat mode, 3: auto power shut-off timer, 5: auto power shut-off mode).
The selected number will blink in the left side of the display.
USER PROGRAMS
3
Press the print (
) key. The entered program number will be steadily lit and the
currently selected parameter number for the program will blink on the right side of
the display.
4
Select the desired parameter using the right copy quantity (
parameter number will blink on the right of the display.
Program
Mode
No.
1
Auto clear time
2
3
5
Preheat mode
Auto power shutoff timer
Auto power shutoff mode
) key. The entered
Parameters
0 e OFF
3 e 90 sec.
0 e 30 sec.
0 e 2 min.
3 e 30 min.
0 e OFF
1 e 30 sec.
4 e 120 sec.
1 e 60 sec.
* 1 e 5 min.
4 e 60 min.
* 1 e ON
* 2 e 60 sec.
* 2 e 90 sec.
2 e 15 min.
5 e 120 min.
4
Factory default settings are indicated with an asterisk (*).
Press the print (
) key. The right-hand number in the display will be steadily lit
and the entered value will be stored.
To change the setting or to set another mode, press the clear (
copier will return to step 2.
6
Press the light (
) or dark (
Special functions
5
) key. The
) key to return to the normal copy mode.
25
5
SUPPLIES AND USER MAINTENANCE
This chapter describes how to replace the TD cartridge and the drum cartridge and how to
check the total number of copies.
TD CARTRIDGE REPLACEMENT
The TD cartridge replacement required ( ) indicator will light up when toner is needed. For
more information on purchasing the TD cartridge, see OPTION AND SUPPLY PART
NUMBERS AND STORAGE on page 38. If copying is continued while the
indicator is lit,
copies will gradually become lighter until the copier stops and the indicator begins blinking.
Replace the old TD cartridge by following the procedure given below.
After the copier stops, it may be possible to make a few more copies by
taking the TD cartridge out of the copier, shaking it horizontally, then
reinstalling it. If copying is not possible after this operation, replace the TD
cartridge.
● During long copy run of a dark original, the ready (
) indicator may blink,
the
indicator light up, and the copier stop, even though toner is left. The
copier will feed toner up to 2 minutes and then the ready ( ) indicator will
light up. Press the print ( ) key to restart copying.
●
5
Supplies and user maintenance
1
Open the side cover while pressing the side cover open button.
Then, push gently on both sides of the front cover to open the cover.
2
Gently pull the TD cartridge out while pressing the lock release button. Dispose of
the old TD cartridge in accordance with local regulations.
Lock release button
26
TD CARTRIDGE REPLACEMENT
3
Install a new TD cartridge. To install the new cartridge, see page 11, INSTALLING
THE TD CARTRIDGE.
4
Close the front cover and then the side cover by pressing the round projections near
the side cover open button. The indicator will go out and the ready ( ) indicator
will light up.
When closing the covers, be sure to close the front cover securely and then
close the side cover. If the covers are closed in the wrong order, the covers
may be damaged.
DRUM CARTRIDGE REPLACEMENT
The useful life of the drum cartridge is approximately 18,000 copies. When the internal counter
reaches approximately 17,000 copies, the drum replacement required ( ) indicator will light
up indicating that replacement of the drum cartridge will be needed soon. For more information
on purchasing the drum cartridge, see OPTION AND SUPPLY PART NUMBERS AND
STORAGE on page 38. When the indicator begins to blink, the copier will stop operating until
the cartridge is replaced. Replace the drum cartridge at this time.
5
1
Open the side cover while pressing the side cover open button.
Then, push gently on both sides of the front cover to open the cover.
2
Gently pull the TD cartridge out while pressing the lock release button. To remove
the TD cartridge, see page 26, step 2.
3
Hold the handle of the drum cartridge and gently pull the cartridge out. Dispose of
the old drum cartridge in accordance with local regulations.
Supplies and user maintenance
Do not remove the protective cover on the drum portion (black paper) of a new
drum cartridge before use. The cover protects the drum against external light.
27
DRUM CARTRIDGE REPLACEMENT
4
Remove the new drum cartridge from the protective bag and remove the protective
cover from the cartridge. Then gently install the new drum cartridge.
Do not touch the surface of the drum (green portion) of the cartridge. Doing so
may cause smudges on the copies.
5
Gently install the TD cartridge. To install the TD cartridge, see page 11, INSTALLING
THE TD CARTRIDGE.
6
Close the front cover and then the side cover by pressing the round projections near
the side cover open button. The drum replacement required ( ) indicator will go
out and the (
) indicator will light up.
When closing the covers, be sure to close the front cover securely and then
close the side cover. If the covers are closed in the wrong order, the covers
may be damaged.
5
Supplies and user maintenance
USER MAINTENANCE
Proper care is essential in order to get clean, sharp copies. Be sure to take a few minutes to
regularly clean the copier.
Do not use thinner, benzene or other volatile cleaning agents. Doing so may
cause deformation, discoloration, deterioration or malfunction.
● Before cleaning, be sure to turn the power switch off and remove the power
cord from the outlet.
●
Cabinet
Wipe the cabinet with a soft, clean cloth.
Original table and original cover
Stains on the glass or cover will also be copied. Wipe the glass and the cover with a soft,
clean cloth. If necessary, dampen the cloth with water or a glass cleaner.
Original table
28
Original cover
USER MAINTENANCE
Transfer charger
If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the
charger using the following procedure.
1
Turn the power switch off.
2
Open the side cover while pressing the side cover open button.
3
Take the charger cleaner out by holding the tab.
Set the charger cleaner onto the transfer charger and gently slide the cleaner back
and forth two or three times.
Slide the charger cleaner from one end to the other end along the groove of
the transfer charger. If the cleaner is stopped on the way, smudges on copies
may occur.
5
Return the charger cleaner to its original position. Close the side cover by pressing
the round projections near the side cover open button.
5
Turn the power switch on.
Supplies and user maintenance
4
When copier is not in use
To prevent entry of dust and foreign matter, store the copier as follows.
1
Remove the power cord and secure the copier using tape (two locations).
29
USER MAINTENANCE
Copier lens cleaning
If white lines appear on copies in the direction of paper travel, make a reduction or enlargement
copy and check to see if the position of the white lines change on the copy paper.
If the lines appear in the same position, clean the copier lens using the following procedure.
When you open the front cover to clean the lens, be sure to finish cleaning
and close the front cover as soon as possible in order to minimize exposure of
the drum cartridge to external light.
1
Pull the paper tray out and take the lens cleaning tool out of the tray. Be careful not
to handle the brush portion of the tool.
Lens cleaning tool
5
Supplies and user maintenance
2
Press the side cover open button to open the cover. Push gently on both sides of the
front cover and open the cover.
3
Press the lock release button on the TD cartridge and remove the cartridge from the
machine (refer to page 26, step 2) and then grasp the handle of the drum cartridge
and gently pull the cartridge to remove it from the machine (refer to page 27, step 3).
Handle the cleaning tool by holding the end of the lens cleaner rod
and the rod
guide .
4
Place the L-shaped hole of the rod guide
onto the projection on the copier frame
and align the positioning groove
on the right side of the cleaning brush with
the guide inside the copier. Use the lens cleaner rod to push the lens cleaner all the
way into the copier and then pull it back. Make sure that the positioning groove
follows the guide within the copier. Repeat this action 2 or 3 times.
Positioning groove
Rod guide
L-shaped hole
Guide
5
Replace the lens cleaning tool into the front of the paper tray. Gently push the paper
tray back into the copier.
6
Reinstall the drum cartridge (refer to page 28, step 4) and the TD cartridge (refer to
page 13, step 6).
7
Close the front cover and then close the side cover by pressing the round projections
near the side cover open button.
When closing the covers, be sure to close the front cover securely and then
close the side cover. If the covers are closed in the wrong order, the covers
may be damaged.
30
6
COPIER TROUBLE?
This chapter describes misfeed removal and troubleshooting.
MISFEED REMOVAL
When the misfeed ( ) indicator blinks or
because of a misfeed.
blinks in the display, the copier will stop
1
Open the side cover while pressing the side cover open button.
2
Check the misfeed location. Remove the misfed paper following the instructions for
each location in the illustration below.
If
blinks in the display, proceed to “A Misfeed in the paper feed area”. (p. 31)
If paper is misfed here, proceed to “B
Misfeed in the fusing area”. (p. 32)
Copier trouble?
If the misfed paper is seen from
this side, proceed to “C Misfeed in
the transport area”. (p. 33)
6
If paper is misfed here, proceed to “A
Misfeed in the paper feed area”. (p. 31)
A Misfeed in the paper feed area
1
Gently remove the misfed paper from the paper feed area as shown in the illustration.
When
blinks in the display and the misfed paper is not seen from the paper
feed area, pull out the paper tray and remove the misfed paper. If the paper cannot
be removed, proceed to “B Misfeed in the fusing area”.
The fusing unit is hot. Do not touch the fusing unit when removing misfed
paper. Doing so may cause a burn or other injury.
Do not touch the surface of the drum (green portion) of the drum cartridge
when removing the misfed paper. Doing so may damage the drum and cause
smudges on copies.
● If the paper has been fed through the manual bypass, do not remove the
misfed paper through the manual bypass. Toner on the paper may stain the
paper transport area, resulting in smudges on copies.
●
31
MISFEED REMOVAL
2
Close the side cover by pressing the round projections near the side cover open
button. The misfeed ( ) indicator will go out and the ready (
) indicator will light
up.
B Misfeed in the fusing area
1
Lower the fusing unit release lever.
Fusing unit release lever
6
2
Gently remove the misfed paper from under the fusing unit as shown in the illustration.
If the paper cannot be removed, proceed to “C Misfeed in the transport area”.
Copier trouble?
The fusing unit is hot. Do not touch the fusing unit when removing misfed
paper. Doing so may cause a burn or other injury.
32
●
Do not touch the surface of the drum (green portion) of the drum cartridge
when removing the misfed paper. Doing so may cause smudges on copies.
●
Do not remove the misfed paper from above the fusing unit. Unfixed toner
on the paper may stain the paper transport area, resulting in smudges on
copies.
MISFEED REMOVAL
3
Raise the fusing unit release lever and then close the side cover by pressing the
round projections near the side cover open button. The misfeed ( ) indicator will
go out and the ready (
) indicator will light up.
C Misfeed in the transport area
1
Lower the fusing unit release lever.
Fusing unit release lever
2
Push gently on both sides of the front cover to open the cover.
3
Rotate the feeding roller in the direction of the arrow and gently remove the misfed
paper from the exit area.
6
Feeding roller
Copier trouble?
4
Raise the fusing unit release lever, close the front cover and then close the side
cover by pressing the round projections near the side cover open button. The misfeed
( ) indicator will go out and the ready (
) indicator will light up.
When closing the covers, be sure to close the front cover securely and then
close the side cover. If the covers are closed in the wrong order, the covers
may be damaged.
33
TROUBLESHOOTING
If any problem occurs, check the list below before contacting the Sharp Service Center.
Problem
Possible cause
Copier plugged in?
Copier does not
operate.
Blank copies
Power save (
indicator on.
Power switch on?
Side cover closed
securely?
Front cover closed?
Is the original placed face
down on the original
table?
Is the copier in the
) preheat mode?
Is the copier in the auto
power shut-off mode?
Is original image too dark
or too light?
Is the copier in the
Copies are too
dark or too light. automatic exposure
mode?
Is the copier in the photo
exposure mode?
Original table or original
Dust, dirt,
cover dirty?
smudges appear
Original
smudged or
on copies.
blotchy?
Is transfer charger clean?
Striped copies
6
Copier trouble?
White lines in the Is the copier lens clean?
copies
Non-standard paper
used?
Paper misfeeds
frequently.
Images rub off
the copy easily.
34
Paper curled or damp?
Pieces of paper inside
copier?
Paper guides in the paper
tray not set properly?
Too much paper in the
paper tray?
Is the copy paper too
heavy?
Paper damp?
Solution
See
page:
Plug the copier into a grounded
outlet.
Turn the power switch on.
Gently close the side cover.
15
Gently close the front cover and
then close the side cover.
Place the original face down on
the original table.
–
16
–
18
Press any key to cancel the
preheat mode.
Press the print (
) key to
cancel the auto power shut-off
mode.
Adjust the exposure manually.
23
Adjust the automatic exposure
level.
36
Cancel the photo exposure
mode.
Clean regularly.
20
Use a clean original.
–
Clean the transfer charger.
29
Clean the copier lens.
30
Use standard paper. If using
special papers, feed the paper
through the manual bypass.
Store copy paper flat in the
wrapper in a dry location.
Remove all pieces of misfed
paper.
Set the guides properly
depending on the paper size.
Remove excessive paper from
the paper tray.
Use copy paper within the
specified range.
Replace with dry copy paper. If
the copier is not used for long
time, remove the paper from the
paper tray and store it in its
wrapper in a dry location.
17
23
20
28
–
31
13
14
17
38
STATUS INDICATORS
When the following indicators light up or blink on the operation panel or the following
alphanumeric codes appear in the display, solve the problem immediately referring to both
the table below and the relevant page.
Indication
Drum replacement
required indicator
TD cartridge
replacement
required indicator
Misfeed indicator
Cause and remedy
See
page:
Steadily Replacement of drum cartridge will be needed
lit
soon. Prepare a new cartridge.
38
Blinking Drum cartridge must be replaced. Replace it
with a new one.
27
Steadily Replacement of TD cartridge will be needed
soon. Prepare a new cartridge.
lit
38
Blinking TD cartridge must be replaced. Replace it with
a new one.
26
A misfeed has occurred. Remove the misfed
Blinking paper referring to the description of "Misfeed
removal."
31
"CH" is blinking in the display. The TD cartridge is not installed. Check if the
cartridge is installed.
"CH" is steadily lit in the
display.
"P" is blinking in the display.
26
–
Paper tray is empty. Load copy paper.
13
A misfeed has occurred in the paper tray.
Remove the misfed paper.
31
Paper tray is not securely installed. Push the
tray in securely.
–
The copier will not function. Turn the power
A letter and a number appear switch off, remove the power cord from the
alternately.
outlet, and contact your authorized service
representative.
6
Copier trouble?
Side cover is open. Close the side cover
securely by pressing the round projections
near the side cover open button.
–
DISPLAYING TOTAL NUMBER OF COPIES
Use the following procedure to display the total number of copies.
1
Press the clear (
) key to reset the display to zero.
2
Press and hold down the clear ( ) key for approximately 5 seconds. The total
number of copies will appear in two steps, each with three digits.
Example: Total number of copies is 1,234.
35
AUTOMATIC EXPOSURE ADJUSTMENT
The automatic exposure level can be adjusted to suit your copying needs.
1
Press the exposure mode selector key to select the photo (
2
Press and hold down the exposure mode selector key for approximately 5 seconds.
The photo ( ) indicator will go out and the AUTO indicator will begin to blink. One
or two exposure indicators corresponding to the automatic exposure level which
has been selected will light up.
3
Press the light ( ) or dark ( ) key to lighten or darken the automatic exposure
level as desired.
If exposure level 2 is selected, the two left-handmost indicators for that level will
light up simultaneously. Also, if level 4 is selected, the two right-handmost indicators
for that level will light up simultaneously.
4
Press the exposure selector key. The AUTO indicator will stop blinking and light up
steadily.
6
) mode.
Copier trouble?
This automatic exposure level will remain in effect until you change it again by
this procedure.
36
7
APPENDIX
SPECIFICATIONS
Type
Copy system
Originals
Original size
Copy sizes
Digital copying machine, desk-top type
Dry, electrostatic transfer
Sheets, bound documents
Max. 10" x 14"
8-1/2" x 14" to 3-1/2" x 5-1/2"
(Feed copy paper lengthwise only.)
Image loss: Max. 5/32" (4 mm) (leading and trailing edges)
Max. 1/8" (3 mm) (either of the other edges)
Copy speed
10 copies/min.
Continuous copying
Max. 99 copies; subtractive counter
First-copy time
9.6 sec. (normal copying mode)
16.0 sec. or less (copying from preheat mode)
23.0 sec. or less (copying from auto power shut-off mode)
23.0 sec. or less (copying immediately after power on)
Copy ratio
Variable: 50% to 200% in 1% increments (total 151 steps)
Fixed: 50%, 64%, 78%, 100%, 129%, 200%
Exposure system
Moving optical source, slit exposure (stationary platen) with
automatic exposure
Copy paper feed
One paper tray with automatic feed (250 sheets); one singlesheet manual bypass
Fusing system
Heat rollers
Development system
Magnetic brush development
Light source
Xenon lamp
Resolution
Scan: 400 dpi
Output: 600 dpi
Gradation
Scan: 256 levels
Output: 2 levels
Memory
AL-1000: N/A
AL-1010: 6MB
Power supply
AC 120V (±10%), 60 Hz (±2%)
Power consumption
1,000 W
Overall dimensions
23.9" (W) x 17.5" (D) (607 mm (W) x 445 mm (D))
Weight
Approx. 39.7 lbs. (18 kg), TD and drum cartridges included
Copier dimensions
20.4" (W) x 17.5" (D) x 11.5" (H)
(518 mm (W) x 445 mm (D) x 293 mm (H))
Operating conditions
Temperature: 50°F to 86°F (10°C to 30°C)
Humidity: 20% to 85%
Noise level
Sound Power Level LWA (1B=10dB)
Copying: 6.6 [B (A)], Standby: Background noise level
Sound Pressure Level LPA (bystander positions)
Copying: 40 [dB (A)], Standby: Background noise level
Noise emission measurement in accordance with ISO 7779.
First-copy time may differ depending on operating conditions, such as power-supply voltage
and room temperature.
As a part of our policy of continuous improvement, SHARP reserves the right
to make design and specification changes for product improvement without
prior notice. The performance specification figures indicated are nominal values
of production units. There may be some deviation from these values in individual
units.
7
Appendix
37
OPTION AND SUPPLY PART NUMBERS AND STORAGE
When ordering supplies and option, please use the correct part numbers as listed below.
Be sure to use only genuine SHARP parts and supplies.
Supply list
Supply
Part number
Usable life
TD cartridge
Drum cartridge
AL-100TD
AL-100DR
Approx. 6,000 sheets*
Approx. 18,000 sheets
* Based on copying onto letter-type paper at 5% toned area
(The life of the TD cartridge which has been included in the copier at the factory is
approximately 2,000 sheets.)
Option list
When purchasing an optional printer upgrade kit, be sure to select the kit which is compatible
to your copier. If the printer upgrade kit is not proper, your copier cannot be used as a printer.
7
Part name
Part number
Contents
AL-1000
Printer upgrade kit
(with memory)
AL-11PK
Printer board,
printer driver (CD-ROM),
printer memory,
interface cable
(for IBM PC/AT or compatible
computers)
AL-1010
Printer upgrade kit
AL-10PK
Printer board,
printer driver (CD-ROM),
interface cable
(for IBM PC/AT or compatible
computers)
Appendix
Copier model
Proper storage
1. Store the supplies in a location that is:
●
clean and dry,
●
at a stable temperature,
●
not exposed to direct sunlight.
2. Store copy paper in the wrapper and lying flat.
●
38
Paper stored out of the wrapper or in packages standing on end may curl or get damp,
resulting in paper misfeeds.
MOVING INSTRUCTIONS
When moving this copier, follow the procedure below.
When moving this copier, be sure to remove the TD cartridge in advance.
1
Turn the power switch off and disconnect the power cord.
2
q Open the side cover while pressing the side cover open button. w Push gently
on both sides of the front cover to open the cover.
3
Gently pull the TD cartridge out while pressing the lock release button. See page
26, TD CARTRIDGE REPLACEMENT.
4
Close the front cover and then the side cover by pressing the round projections near
the side cover open buttton.
When closing the covers, be sure to close the front cover securely and then
close the side cover. If the covers are closed in the wrong order, the covers
may be damaged.
5
Raise the handle of the paper tray and pull the paper tray out until it stops.
6
Push the center of the pressure plate down until it locks in place and lock the plate
using the pressure plate lock which has been stored in the front of the paper tray.
7
Use a coin (or suitable object) to attach to the left side of the copier the screw that
has been stored in the front of the paper tray.
Appendix
7
When shipping the copier, the screw must be reinstalled to prevent shipping
damage.
8
Push the paper tray back into the copier.
9
Close the paper output tray extension, and attach the packing materials and tape
which were removed during installation of the copier. See page 11, REMOVING
PROTECTIVE PACKING MATERIALS.
10
Pack the copier into the carton. See page 10, CHECKING PACKED COMPONENTS
AND ACCESSORIES.
39
INDEX
A
Auto clear . . . . . . . . . . . . . . . . . . . . 23, 24
Automatic exposure adjustment . . . . . . 36
Auto power shut-off mode . . . . . . . . 23, 24
C
Cautions . . . . . . . . . . . . . . . . . . . . . . . . . 3
Cautions on handling . . . . . . . . . . . . . . . 9
Charger cleaner . . . . . . . . . . . . . . . . . . 29
Copier trouble? . . . . . . . . . . . . . . . . . . . 31
Copying
- large original . . . . . . . . . . . . . . . . . . . . 19
- normal. . . . . . . . . . . . . . . . . . . . . . . . . 18
- reduction/enlargement . . . . . . . . . . . . 20
- through manual bypass . . . . . . . . . . . 21
- two-sided . . . . . . . . . . . . . . . . . . . . . . 22
Copy paper . . . . . . . . . . . . . . . . . . . . . . 17
Copy quantity . . . . . . . . . . . . . . . . . . . . 18
Copy ratio . . . . . . . . . . . . . . . . . . . . . . . 20
D
Dark key . . . . . . . . . . . . . . . . . . . . . . . . 20
Drum cartridge
- indicator . . . . . . . . . . . . . . . . . . . . . 7, 35
- replacement . . . . . . . . . . . . . . . . . . . . 27
E
Enlargement . . . . . . . . . . . . . . . . . . . . . 20
Exposure adjustment . . . . . . . . . . . . . . 20
F
Features . . . . . . . . . . . . . . . . . . . . . . . . . 4
Fixed copy ratio . . . . . . . . . . . . . . . . . . . 21
Fusing unit release lever . . . . . . . . . . 6, 32
I
Initial settings . . . . . . . . . . . . . . . . . . . . 16
Installation
- location . . . . . . . . . . . . . . . . . . . . . . . . . 8
- TD cartridge . . . . . . . . . . . . . . . . . . . . 11
L
Lens cleaning tool . . . . . . . . . . . . . . . . . 30
Light key . . . . . . . . . . . . . . . . . . . . . . . . 20
Loading copy paper . . . . . . . . . . . . . . . . 13
M
Maintenance . . . . . . . . . . . . . . . . . . . . . 28
Manual bypass . . . . . . . . . . . . . . . . . 6, 21
Manual exposure . . . . . . . . . . . . . . . . . . 20
Manual feeding . . . . . . . . . . . . . . . . . . . 21
Misfeed removal
- fusing area . . . . . . . . . . . . . . . . . . . . . 32
- paper feed area . . . . . . . . . . . . . . . . . 31
- transport area . . . . . . . . . . . . . . . . . . . 33
Moving instructions . . . . . . . . . . . . . . . . 39
N
Names
- operation panel . . . . . . . . . . . . . . . . . . . 7
- part . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
O
ON LINE . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operation panel
- initial settings . . . . . . . . . . . . . . . . . . . 16
- part names . . . . . . . . . . . . . . . . . . . . . . 7
Options . . . . . . . . . . . . . . . . . . . . . . . . . 38
Original cover . . . . . . . . . . . . . . . . . . . . . 6
Original table . . . . . . . . . . . . . . . . . . . . . . 6
P
Packed components . . . . . . . . . . . . . . . 10
Paper
- loading . . . . . . . . . . . . . . . . . . . . . . . . 13
- special . . . . . . . . . . . . . . . . . . . . . . . . 17
- specifications . . . . . . . . . . . . . . . . . . . 17
Paper feed area . . . . . . . . . . . . . . . . . . 31
Paper output tray . . . . . . . . . . . . . . . . . . . 6
Paper output tray extension . . . . . . . 6, 18
Paper size . . . . . . . . . . . . . . . . . . . . . . . 17
Paper transport area . . . . . . . . . . . . . . . 33
Paper tray . . . . . . . . . . . . . . . . . . . . . . . . 6
Part names . . . . . . . . . . . . . . . . . . . . . . . 6
Photo mode . . . . . . . . . . . . . . . . . . . . 7, 20
Power cord . . . . . . . . . . . . . . . . . . . 10, 15
Power on . . . . . . . . . . . . . . . . . . . . . . . . 16
Power save modes . . . . . . . . . . . . . 23, 24
Power switch . . . . . . . . . . . . . . . . . . . 6, 16
Preheat mode . . . . . . . . . . . . . . . . . . 23,24
INDEX
Print key . . . . . . . . . . . . . . . . . . . . . . . . 18
Protective packing materials . . . . . . . . . 11
R
Ready indicator . . . . . . . . . . . . . . . . . . . . 7
Reduction . . . . . . . . . . . . . . . . . . . . . . . 20
Replacement
- drum cartridge . . . . . . . . . . . . . . . . . . 27
- TD cartridge . . . . . . . . . . . . . . . . . . . . 26
S
Screw . . . . . . . . . . . . . . . . . . . . . . . 11, 14
Special paper . . . . . . . . . . . . . . . . . . . . 17
Specifications
- copier . . . . . . . . . . . . . . . . . . . . . . . . . 37
- paper . . . . . . . . . . . . . . . . . . . . . . . . . 17
Status indicators . . . . . . . . . . . . . . . . . . 35
Supply
- life . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
- part number . . . . . . . . . . . . . . . . . . . . 38
- storage . . . . . . . . . . . . . . . . . . . . . . . . 38
T
TD cartridge
- indicator . . . . . . . . . . . . . . . . . . . . . 7, 35
- installation . . . . . . . . . . . . . . . . . . . . . . 11
- replacement . . . . . . . . . . . . . . . . . . . . 26
Toner save mode . . . . . . . . . . . . . . . . . . 23
Total number of copies . . . . . . . . . . . . . 35
Transfer charger . . . . . . . . . . . . . . . . 6, 29
Troubleshooting . . . . . . . . . . . . . . . . . . 34
Two-sided copying . . . . . . . . . . . . . . . . 22
U
User maintenance
- cabinet . . . . . . . . . . . . . . . . . . . . . . . .
- copier lens cleaning . . . . . . . . . . . . . .
- original cover . . . . . . . . . . . . . . . . . . .
- original table . . . . . . . . . . . . . . . . . . . .
- transfer charger . . . . . . . . . . . . . . . . .
28
30
28
28
29
Z
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
MEMO
MEMO
MEMO
♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this
equipment not expressly approved by the manufacturer could void the user’s
authority to operate this equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠
♠
♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠ ♠
♠
♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠ ♠
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135.
SHARP CORPORATION
© 1995 SHARP CORPORATION
PRINTED IN JAPAN
TINSE0067QSZZw
Download PDF