PANPTDS12KEJ_Specs 1.74 mb

PANPTDS12KEJ_Specs 1.74 mb

S

P E C

F

I L E

P r o d u c t N u m b e r :

PT-DS12K

P r o d u c t N a m e :

3-Chip DLP ™ Projector

As of April 2013. Specifications and appearance are subject to change without notice.

SFD12M021

1 / 1 8

S

P E C

F

I L E

3-Chip DLP ™ Projector

PT-DS12K

Specifications

Main unit

Power supply

Power consumption

DLP™ chip

Lens

Lamp

Screen size

Brightness* 2

Center-to-corner uniformity* 2

Contrast* 2

Resolution

Scanning frequency

120 V AC, 50/60 Hz

220–240 V AC, 50/60 Hz

Panel size

Display method

Pixels

SDI

HDMI/DVI-D/RGB

YP

B

P

R

(YC

B

C

Video/S-Video

R

)

120 V AC, 9.1 A, 50/60 Hz

220–240 V AC, 4.8 A, 50/60 Hz

980 W (1,010 VA) (0.2 W with standby mode set to eco.*

1

6 W with standby mode set to normal. Both with fan stopped.)

950 W (980 VA) (0.3 W with standby mode set to eco.*

1

9 W with standby mode set to normal. Both with fan stopped.)

24.1 mm (0.95 inches) diagonal (4:3 aspect ratio)

DLP™ chip × 3 (R, G, B), DLP™ projection system

1,470,000 (1,400 × 1,050) × 3, total of 4,410,000 pixels

Optional powered zoom/focus lenses

380 W UHM lamps (× 2) (dual lamp, high mode)

1.78–25.4 m (70 – 1,000 inches) (1.78–15.24 m (70 – 600 inches) with the

ET-D75LE8), 4:3 aspect ratio

12,000 lumens (dual lamp, high mode)

90%

10,000:1 (full on/full off, in dynamic iris 3 mode)

1,400 × 1,050 pixels (Input signals that exceed this resolution will be converted to 1,400 × 1,050 pixels.)

Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit):

SMPTE ST 372 compliant: 1125(1080)/60i, 1125(1080)/50i,

1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p

Dual-link HD-SDI signal (X Y Z 4:4:4 12-bit):

SMPTE ST 372 compliant: 2048 × 1080/24p, 2048 × 1080/24sF,

3G-SDI signal (RGB 4:4:4 12-bit/10-bit):

SMPTE ST 424 compliant: 1125(1080)/60i, 1125(1080)/50i,

1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p

3G-SDI signal (YP

B

P

R

4:2:2 10-bit):

SMPTE ST 424 compliant: 1125(1080)/60p, 1125(1080)/50p

HD-SDI signal (YP

B

P

R

4:2:2 10-bit):

SMPTE ST 292 compliant: 750(720)/60p, 750(720)/50p, 1125(1035)/60i,

1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p,

1125(1080)/24sF, 1125(1080)/30p

SD-SDI signal (YC

B

C

R

4:2:2 10-bit):

SMPTE ST 259 compliant: 525i(480i), 625i(576i)

Horizontal: 15 kHz–100 kHz, vertical: 24 Hz – 120 Hz, dot clock: 25–162 MHz or lower (HDMI/DVI: 25 MHz – 162 MHz)

525i (480i):

625i (576i):

525p (480p):

625p (576p): f

H

15.75 kHz; f

V

60 Hz, f

H

15.63 kHz; f

V

50 Hz, f

H

31.50 kHz; f

V

60 Hz, f

H

31.25 kHz; f

V

50 Hz,

750 (720)/60p: f

H

45.00 kHz; f

V

60 Hz,

750 (720)/50p: f

H

37.50 kHz; f

V

50 Hz,

1125 (1035)/60i: f

H

33.75 kHz; f

V

60 Hz,

1125 (1080)/60i: f

H

33.75 kHz; f

V

60 Hz,

1125 (1080)/50i: f

H

28.13 kHz; f

V

50 Hz,

1125 (1080)/25p: f

H

28.13 kHz; f

V

25 Hz,

1125 (1080)/24p: f

H

27.00 kHz; f

V

24 Hz,

1125 (1080)/24sF: f

H

27.00 kHz; f

V

48 Hz,

1125 (1080)/30p: f

H

33.75 kHz; f

V

30 Hz,

1125 (1080)/60p: f

H

67.50 kHz; f

V

60 Hz,

1125 (1080)/50p: f

H

56.25 kHz; f

V

50 Hz f

H

: 15.75 kHz, f

V

: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60] f

H

: 15.63 kHz, f

V

: 50 Hz [PAL/PAL-N/SECAM]

As of April 2013

SFD12M021

2 / 1 8

S

P E C

F

I L E

3-Chip DLP ™ Projector

PT-DS12K

Optical axis shift

Keystone correction range

Installation

Terminals

Vertical

Horizontal

SDI IN 1

SDI IN 2

HDMI IN

DVI-D IN

RGB 1 IN

R, G, B

Y, P

B

, P

R

(Y, C

B

, C

R

)

S-Video signal

RGB 2 IN

R, G, B

Y, P

B

, P

R

(Y, C

B

, C

R

)

±50% (±40% with the ET-D75LE6) from center of screen, powered

±30% (±20% with the ET-D75LE6) from center of screen, powered

NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50.

Vertical ±40°, horizontal ±15°

(vertical ±22° and horizontal ±15° with the ET-D75LE5/LE50, vertical ±28° and horizontal ±15° with the ET-D75LE6)

When using only the KEYSTONE correction of the Geometric Adjustment function: Vertical ±40°, horizontal ±15°

When using the optional upgrade kit ET-UK20* 3 :

Vertical ±40° and horizontal ±40° with the ET-D75LE1/LE2/LE10/LE20, vertical ±45°and horizontal ±40° with the ET-D75LE3/LE4/LE30/LE40, vertical ±22° and horizontal ±15° with the ET-D75LE5/LE50, vertical ±28° and horizontal ±15° with the ET-D75LE6

When using both the KEYSTONE and CURVED corrections of the Geometric

Adjustment function: Vertical ±20°, horizontal ±15°

(vertical ±8° and horizontal ±8° with the ET-D75LE5/50, vertical ±10° and horizontal ±10° with the ET-D75LE6)

Ceiling/floor, front/rear

BNC × 1,

Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-A)

3G-SDI signal: SMPTE ST 424 compliant

HD-SDI signal: SMPTE ST 292 compliant

SD-SDI signal: SMPTE ST 259 compliant

BNC × 1,

Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-B)

HD-SDI signal: SMPTE ST 292 compliant

SD-SDI signal: SMPTE ST 259 compliant

HDMI 19-pin × 1, Deep Color, compatible with HDCP,

525i(480i)* 4 , 625i(576i)* 4 , 525p(480p), 625p(576p), 750(720)/60p,

750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p,

1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p,

1125(1080)/50p

VGA (640 × 480) – WUXGA*

5

(1,920 × 1,200), dot clock: 25 MHz –162 MHz

NOTE: Compatible with non-interlaced signals only.

DVI-D 24-pin × 1, DVI 1.0 compliant, HDCP compatible, for single link only

525i(480i)* 4 , 625i(576i)* 4 , 525p(480p), 625p(576p), 750(720)/60p,

750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p,

1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p,

1125(1080)/50p

VGA (640 × 480) – WUXGA* 5 (1,920 × 1,200), dot clock: 25 MHz –162 MHz

NOTE: Compatible with non-interlaced signals only.

BNC × 5

R: 0.7 Vp-p, 75 ohms,

G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,

B: 0.7 Vp-p, 75 ohms

HD, VD/SYNC: TTL, high impedance, positive/negative automatic

NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.

Y: 1.0 Vp-p (including sync signal), P

B

/P

R

(C

B

/C

R

): 0.7 Vp-p, 75 ohms

Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms

D-sub HD 15-pin (female) × 1

R: 0.7 Vp-p, 75 ohms,

G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,

B: 0.7 Vp-p, 75 ohms

HD, VD/SYNC: TTL, high impedance, positive/negative automatic

NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.

Y: 1.0 Vp-p (including sync signal), P

B

/P

R

(C

B

/C

R

): 0.7 Vp-p, 75 ohms

As of April 2013

SFD12M021

3 / 1 8

S

P E C

F

I L E

3-Chip DLP

Projector

PT-

DS12K

Power cord length

Cabinet materials

Dimensions (W × H × D):

Weight*

7

Operation noise*

2

Operating temperature

Operating humidity

VIDEO IN

3D SYNC 1 IN/OUT

3D SYNC 2 OUT

SERIAL IN

SERIAL OUT

REMOTE 1 IN

REMOTE 1 OUT

REMOTE 2 IN

LAN

BNC × 1, 1.0 Vp-p, 75 ohms

BNC × 1, 1.0 Vp-p, 75 ohms

Input: TTL, high impedance. Output: TTL, max. 10 mA

BNC × 1, 1.0 Vp-p, 75 ohms, TTL, max. 10 mA

D-sub 9-pin (female) × 1 for external control (RS-232C compliant)

D-sub 9-pin (male) × 1 for link control (RS-232C compliant)

M3 jack × 1 for wired remote control

M3 jack × 1 for link control

D-sub 9-pin × 1 for external control (parallel)

RJ-45 × 1 for network connection, 100Base-TX/10Base-T, compliant with PJLink™ (class 1)

3.0 m (9 10 in)

Molded plastic

530 × 200*

6

× 548.5 mm

(20-7/8 × 7-7/8*

6

× 21-19/32 inches) (without lens)

24 kg (52.9 lbs) (without lens)

45 dB (high mode), 43 dB (middle mode), 37 dB (eco mode)

0°– 45°C (32°–113°F) *

8

10%– 80% (no condensation)

Remote control unit

Power supply

Operation range*

9

Dimensions (W × H × D)

Weight

3 V DC (AA/R6 type battery × 2)

Approx. 30 m (98 5 in) when operated from directly in front of the signal receptor

51 × 176 × 28 mm (2 × 6-15/16 × 1-3/32 inches)

Approx. 134 g (4.7 oz) (including batteries)

Supplied accessories

Power cord (×1) (x2 for PT-DS12KE)

Wireless/wired remote control unit (× 1)

Batteries for remote control (AA/R6 type × 2)

Lens drop-prevention screw (× 1)

Softwar e CD-ROM (Logo Transfer Software, Multi Projector Monitoring

& Control Software) (× 1)

Optional accessories

Zoom lens (1.0 –1.2:1)

Zoom lens (1.4 –1.8:1)

Zoom lens (1.8 – 2.6:1)

Zoom lens (2.6 – 5.1:1)

Zoom lens (5.0 – 8.0:1)

Zoom lens (7.9 –15.0:1)

Fixed-focus lens (0.8:1)

Lens motor cover

Ceiling mount bracket

Attachment for ceiling mount bracket

Frame

Smoke cut filter

Replacement smoke cut filter

Upgrade kit

Replacement lamp unit

Replacement lamp unit for portrait mode

Replacement filter unit

ET-D75LE6

ET-D75LE10

ET-D75LE20

ET-D75LE30

ET-D75LE40

ET-D75LE8

ET-D75LE50

ET-D75MC1

ET-PKD310H (for high ceilings)

ET-PKD310S (for low ceilings)

ET-PAD310

ET -PFD310

ET -SFD320

ET-SFR320

ET-UK20

ET-LAD310A (one bulb)

ET-LAD310AW (a set of two bulbs)

ET-LAD320P (one bulb)

ET-LAD320PW (a set of two bulbs)

ET-EMF320

Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.

*1 When the standby mode is set to eco, network functions such as power on over the LAN network will not operate, and the serial output terminal cannot be used. Also, only certain commands can be received for external control using the serial terminal.

As of April 2013

SFD12M021

4 / 1 8

S

P E C

F

I L E

3-Chip DLP

Projector

PT-

DS12K

*2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.

*3 Up to a total of ±55° during simultaneous horizontal and vertical correction.

*4 Only compatible with dot clock frequency of 27 MHz (pixel repetition signal)

*5 WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).

*6 With legs at shortest position.

*7 Average value (excluding the optional lens). May differ depending on models.

*8 The operating temperature range is 0 °C to 40 °C (32 °F to 104 °F) when the FAN CONTROL is set to HIGH ALTITUDE MODE (for altitudes from

1,400 m to 2,700 m (4,593 ft to 8,858 ft) above sea level). When the projector is used with the ET-SFD320 Smoke Cut Filter, the operating temperature range is 0 °C to 35 °C (32 °F to 95 °F), and the projector cannot be used in places at high altitude. The operating temperature range is 0 °C to 40 °C

(32 °F to 104 °F) when the ET-LAD320P/LAD320PW lamp is mounted and the projector is used in portrait configuration. The operating temperature range is 0 °C to 35 °C (32 °F to 95 °F) when the FAN CONTROL is set to HIGH ALTITUDE MODE (for altitudes from 1,400 m to 2,700 m (4,593 ft to

8,858 ft) above sea level). When the projector is used with the ET-SFD320 Smoke Cut Filter, the operating temperature range is 0 °C to 30 °C (32 °F to 86 °F).

*9 Operation range differs depending on environments.

Dimensions

Terminals

As of April 2013

SFD12M021

462 (18-3/16)

530 (20-7/8)

unit : mm (inch)

NOTE: This illustration is not drawn to scale.

26

(1-1/32)

468 (18-7/16)

6

7

4

5

1

2

3

Remote 1 input

Remote 1 output

Remote 2 input

Serial input

Serial output

SDI 1 input

SDI 2 input

8

9

HDMI input

RGB 1 input

10 RGB 2 Input

11 DVI-D input

12 Video input

13 3D sync 1 input/output

14 3D sync 2 output

15 LAN connector

5 / 1 8

S

P E C

F

I L E

3-Chip DLP

Projector

Standard setting-up position

Upper edge of projected image

L

Projected image

L

Lower edge of projected image

φ

60.5

(12-3/8)

* 1 198 342

(7-25/32) (13-15/32)

PT-

DS12K

*1 When the lens protrudes to the maximum.

212 mm (8-11/32) with the ET-D75LE6

125 mm (4-29/32) with the ET-D75LE10

121 mm (4-3/4) with the ET-D75LE20

121 mm (4-3/4) with the ET-D75LE30

124 mm (4-7/8) with the ET-D75LE40

254 mm (10) with the ET-D75LE8

203 mm (8) with the ET-D75LE50

*2 Adjustable in 40 mm (1-9/16) steps.

unit : mm (inch)

Projected image

L

100

(3-15/16)

100

(3-15/16)

NOTE:

Illustrations show the projector installed using optional ceiling mount bracket

ET-PKD310H and an optional lens.

This illustration is not drawn to scale.

C a u t i o n :

• All construction work should be done by a qualified technician.

• When mounting to the ceiling, use the special mounting bracket.

Furthermore, in order to prevent it from falling down from the ceiling, use the supplied wire on the mounting bracket.

As of April 2013

SFD12M021

6 / 1 8

S

P E C

F

I L E

3-Chip DLP ™ Projector

PT-DS12K

Projection distance for 4:3 aspect ratio screen

(ET-D75LE6/D75LE10/D75LE20/D75LE30/D75LE40/D75LE8/D75LE50)

Screen size

(diagonal)

ET-D75LE6

Zoom lens min.

max.

ET-D75LE10

Zoom lens min.

max.

Distance to screen (L)

ET-D75LE20

Zoom lens min.

max.

Zoom

ET-D75LE30

Zoom lens min.

max.

ET-D75LE40

Zoom lens min.

max.

Unit: meters

Fixed-focus

Height from the edge of screen to center of lens (H)

ET-D75LE8

Zoom lens min.

max.

ET-D75LE50

Fixed-focus lens

Zoom lenses

Except

ET-D75LE6

ET-D75LE6

Fixedfocus lens

[m] / [in]

1.78

/

2.03

/

70

80

1.39

1.60

1.66

1.91

1.95

2.24

2.52

2.89

2.52

2.89

3.66

4.20

3.64

4.17

7.10

8.13

7.02

8.05

11.29

12.92

11.09

12.73

21.14

24.22

1.03

1.19

0.00

– 1.07

0.00

– 1.22

0.11

– 0.96

0.12

– 1.10

0.53

0.61

2.29

2.54

3.05

3.81

5.08

6.35

7.62

10.16

12.70

15.24

17.78

/ 700 14.43 17.29 20.23 26.15 25.91 37.65 37.38 72.54 71.64 114.30 114.38

20.32

/

/

/

/

/

/

/

/

/

/

/

90

100

120

150

200

250

300

400

500

600

800

1.81

2.01

2.43

3.05

4.08

5.12

6.15

8.22

10.29

12.36

16.50

2.16

2.41

2.90

3.65

4.89

6.13

7.37

9.85

12.33

14.81

19.77

2.53

2.82

3.40

4.27

5.72

7.17

8.62

11.52

14.42

17.33

23.13

3.27

3.64

4.39

5.52

7.39

9.27

11.14

14.90

18.65

22.40

29.90

3.26

3.63

4.37

5.49

7.34

9.20

11.06

14.77

18.48

22.20

29.62

4.74

5.28

6.36

7.98

10.67

13.37

16.07

21.46

26.86

32.25

43.05

4.71

9.17

10.21

5.24

6.32

12.29

15.41

7.92

10.60

20.60

13.28

15.96

21.31

26.67

32.03

42.74

25.80

30.99

41.38

51.77

62.15

82.93

9.07

14.56

16.19

10.10

12.15

19.46

24.37

15.23

20.36

32.54

25.48

30.61

40.87

51.12

61.38

40.72

48.89

65.25

81.60

97.95

81.89 130.65

14.37

16.01

19.29

24.21

32.40

40.60

48.80

65.19

81.59

97.98

130.77

27.29

30.36

36.50

45.72

61.08

76.44

91.79

122.51

153.23

183.95

1.35

1.50

1.82

2.29

3.08

3.87

4.65

6.23

7.81

9.38

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

1.37

1.52

1.83

2.29

3.05

3.81

4.57

6.10

7.62

9.14

0.14

0.15

0.18

0.23

0.31

0.38

0.46

0.61

0.76

0.91

1.23

1.37

1.65

2.06

2.74

3.43

4.12

5.49

6.86

8.23

0.69

0.76

0.91

1.14

1.52

1.91

2.29

3.05

3.81

4.57

– 10.96 0.00 – 10.67 1.07 – 9.60 5.33

– 12.53 0.00 – 12.19 1.22 – 10.97 6.10

22.86

/ 900 18.57 22.25 26.03 33.65 33.33 48.44 48.10 93.32 92.15 147.01 147.17

20.64 24.73 28.93 37.40 37.05 53.84 53.45 103.71 102.41 163.36 163.56

– 14.11 0.00 – 13.72 1.37 – 12.34 6.86

– 15.68 0.00 – 15.24 1.52 – 13.72 7.62

Screen size

(diagonal)

ET-D75LE6

Zoom lens min.

max.

ET-D75LE10

Zoom lens min.

max.

Distance to screen (L)

ET-D75LE20

Zoom lens min.

max.

Zoom

ET-D75LE30

Zoom lens min.

max.

ET-D75LE40

Zoom lens min.

max.

Unit: feet

Fixed-focus

Height from the edge of screen to center of lens (H)

ET-D75LE8

Zoom lens min.

max.

ET-D75LE50

Fixed-focus lens

Zoom lenses

Except

ET-D75LE6

ET-D75LE6

Fixedfocus lens

[m] / [in]

1.78

2.03

/

/

70

80

4.6

5.2

5.5

6.3

6.4

7.3

8.3

9.5

8.3

9.5

12.0

13.8

11.9

13.7

23.3

26.7

23.0

26.4

37.0

42.4

36.4

41.8

69.4

79.4

3.4

3.9

0.0

0.0

3.5

4.0

2.29

2.54

3.05

3.81

/

/

/

/ 90

100

120

150

5.9

6.6

8.0

10.0

13.4

16.8

27.0

33.8

7.1

7.9

9.5

12.0

16.0

8.3

9.2

11.1

14.0

18.8

23.5

37.8

47.3

10.7

11.9

14.4

18.1

24.3

10.7

11.9

14.3

18.0

24.1

30.2

48.5

60.6

15.5

17.3

20.9

26.2

35.0

15.4

17.2

20.7

26.0

34.8

43.6

69.9

87.5

30.1

33.5

40.3

50.5

169.8

203.9

29.8

47.8

53.1

33.1

39.9

63.8

79.9

50.0

66.8

106.8

47.1

52.5

63.3

79.4

106.3

133.2

160.1

213.9

267.7

89.5

99.6

119.8

150.0

4.4

4.9

6.0

7.5

10.1

0.0

0.0

0.0

0.0

4.5

5.0

6.0

7.5

5.08

6.35

7.62

10.16

12.70

15.24

/

/

/

/

/

/

200

250

300

400

500

600

20.2

40.6

20.1

24.2

32.3

40.4

48.6

28.3

56.8

30.4

36.6

48.9

61.2

73.5

36.3

72.8

43.9

52.7

70.4

88.1

105.8

52.4

105.1

67.6

84.6

101.7

135.8

83.6

100.4

160.4

134.1

167.7

201.4

133.6

214.1

267.7

321.4

321.5

17.78

/ 700 47.4 56.7 66.4 85.8 85.0 123.5 122.6 238.0 235.0 375.0 375.3

200.4

0.0

– 10.0

250.8

301.2

12.7

15.3

20.4

0.0

0.0

12.5

15.0

401.9

502.7

0.0

– 20.0

25.6

30.8

0.0

– 25.0

603.5

0.0

– 30.0

– 35.9 0.0

20.32

/ 800 54.1 64.8 75.9 98.1 97.2 141.2 140.2 272.1 268.7 428.7 429.0

22.86

/ 900 60.9 73.0 85.4 110.4 109.4 158.9 157.8 306.2 302.3 482.3 482.8

67.7 81.1 94.9 122.7 121.5 176.6 175.4 340.2 336.0 535.9 536.6

41.1

46.3

51.4

0.0

0.0

0.0

0.4

0.4

0.4

0.5

0.6

0.8

1.0

1.3

1.5

2.0

2.5

3.0

5.4

6.7

9.0

– 11.3

– 13.5

50.0 5.0

3.1

3.6

4.0

4.5

18.0

22.5

27.0

7.5

10.0

12.5

15.0

2.5

3.0

3.8

5.0

6.3

1.7

2.0

2.3

• The value for L (distance to screen) varies slightly within ±5% depending on the zoom lens characteristics.

• At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.

• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.

NOTE: When the ET-D75LE50 is mounted, the optical lens shift function cannot be used.

As of April 2013

SFD12M021

7 / 1 8

S

P E C

F

I L E

3-Chip DLP ™ Projector

PT-DS12K

Calculation of the projection distance

For a screen size different from the above, use the equation below to calculate the projection distance.

Aspect ratio 4:3

Zoom lenses

ET-D75LE6

ET-D75LE10

ET-D75LE20

ET-D75LE30

ET-D75LE40

ET-D75LE8 minimum maximum minimum maximum minimum maximum minimum maximum minimum maximum minimum maximum

Fixed-focus lens

ET-D75LE50

L (m) = (diagonal screen size in inches) × 0.0207 – 0.0566

L (m) = (diagonal screen size in inches) × 0.0248 – 0.0736

L (m) = (diagonal screen size in inches) × 0.0290 – 0.0857

L (m) = (diagonal screen size in inches) × 0.0375 – 0.1085

L (m) = (diagonal screen size in inches) × 0.0371 – 0.0832

L (m) = (diagonal screen size in inches) × 0.0540 – 0.1162

L (m) = (diagonal screen size in inches) × 0.0536 – 0.1131

L (m) = (diagonal screen size in inches) × 0.1039 – 0.1765

L (m) = (diagonal screen size in inches) × 0.1026 – 0.1577

L (m) = (diagonal screen size in inches) × 0.1635 – 0.1615

L (m) = (diagonal screen size in inches) × 0.1640 – 0.3862

L (m) = (diagonal screen size in inches) × 0.3072 – 0.3598

L (m) = (diagonal screen size in inches) × 0.0158 – 0.0713

• Distances calculated with the above equations will include slight deviations.

As of April 2013

SFD12M021

8 / 1 8

S

P E C

F

I L E

3-Chip DLP ™ Projector

PT-DS12K

Shift range

Optical axis shift function allows to shift the position of a projected image as shown below.

When the lens except the ET-D75LE6 is mounted

0.3H

H

(Width of projected image) 0.3H

When the ET-D75LE6 is mounted

0.2H

H

(Width of projected image) 0.2H

Standard postition of projected image Standard postition of projected image

NOTE: Because the ET-D75LE50 is a fixed short-throw lens, the lens shift function cannot be used with it.

Installable angle

Install the projector at an angle within the range shown below.

• Vertical direction

The projector may be installed at a vertical angle of 360°.

• Horizontal direction

The projector may be installed at a horizontal angle of ±15°.

360°

+15°

-15°

• Vertical direction in portrait mode with the

ET-LAD320P/LAD320PW mounted

The projector may be installed at a vertical angle of ±15°.

• Horizontal direction in portrait mode with the ET-LAD320P/LAD320PW mounted

The projector may be installed at a horizontal angle of ±15°.

-15°

+15°

+15°

NOTE: The projector cannot be vertically installed all by itself. Also, the terminal side must face downward when vertically installed.

As of April 2013

SFD12M021

9 / 1 8

S

P E C

F

I L E

3-Chip DLP ™ Projector

PT-DS12K

List of compatible signals

The signals that can be input to this projector are shown in the table below. Horizontal scanning frequencies of 15 kHz to 100 kHz, vertical scanning frequencies of 24 Hz to 120 Hz, and a dot clock of

162 MHz maximum can be input.

NOTE: The native resolution of this projector is 1,400 × 1,050 pixels. If the display resolution of the input signal is different from the native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.

Display mode Display resolution

(dots)*

1

NTSC/NTSC4.43/PAL-M/PAL60

PAL/PAL-N/SECAM

525i (480i)

625i (576i)

525i (480i)

625i (576i)

525p (480p)

625p (576p)

750 (720)/60p

750 (720)/50p

720 × 480i

720 × 576i

720 × 480i

720 × 576i

720(1440) × 480i *

2

720(1440) × 576i

* 2

720 × 483

720 × 576

1280 × 720

1920 × 1080i 1125 (1080)/60i

1125 (1080)/50i

1125 (1080)/25p

1125 (1080)/24p

1125 (1080)/24sF

1125 (1080)/30p

1920 × 1080

1920 × 1080i

1920 × 1080

1125 (1080)/60p

1125 (1080)/50p

2K/24p

2K/24sF

VGA400

2048 × 1080

640 × 400

VGA480

SVGA

MAC16

XGA

MXGA

640 × 480

800 × 600

832 × 624

1024 × 768

1152 × 864

MAC21

1152 × 870

*1 The “i” appearing after the resolution indicates an interlaced signal.

*2 Pixel repetition signal only.

*3 SDI 1 only.

*4 For dual-link connection only.

56.5

60.0

65.5

68.7

81.4

98.8

53.7

64.0

67.5

76.7

68.7

35.2

37.9

48.1

46.9

53.7

49.7

39.6

48.4

31.5

37.9

31.5

35.0

37.9

37.5

43.3

Scanning frequency

H V

(kHz) (kHz)

15.7

15.6

15.7

15.6

15.7

15.6

31.5

31.3

45.0

37.5

33.8

28.1

28.1

27.0

27.0

33.8

67.5

56.3

27.0

59.9

50.0

59.9

50.0

59.9

50.0

59.9

50.0

60.0

50.0

60.0

50.0

25.0

24.0

48.0

30.0

60.0

50.0

24.0

75.0

85.1

74.6

50.0

60.0

70.1

75.0

81.6

70.1

85.1

59.9

66.7

72.8

75.0

85.0

56.3

60.3

72.2

85.0

100.0

120.0

60.0

70.0

74.9

85.0

75.1

148.5

74.3

49.5

56.3

57.3

51.9

65.0

75.0

78.8

86.0

25.2

31.5

25.2

30.2

31.5

31.5

36.0

36.0

40.0

50.0

94.5

113.3

139.1

81.6

94.2

108.0

121.5

100.0

Dot clock frequency

(MHz)

13.5

13.5

27.0

27.0

74.3

Format

VIDEO/S-VIDEO

SDI/RGB/YC

B

C

R

HDMI/DVI-D

HDMI/DVI-D/

RGB/YC

B

C

R

SDI/HDMI/DVI-D/

RGB/YP

B

P

R

SDI*

3

/HDMI/DVI-D/

RGB/YP

B

P

R

SDI*

4

HDMI/DVI-D/RGB

As of April 2013

SFD12M021

1 0 / 1 8

S

P E C

F

I L E

3-Chip DLP ™ Projector

Display mode

1280 × 720

1280 × 768

1280 × 800

MSXGA

SXGA

1366×768

SXGA+

WXGA+

UXGA60

WSXGA+

Display resolution

(dots)

1280 × 720

1280 × 768

1280 × 768

1280 × 768

1280 × 800

1280 × 800

1280 × 800

1280 × 960

1280 × 1024

1366 × 768

1400 × 1050

1440 × 900

1600 × 1200

1680 × 1050

*

*

Scanning frequency

H V

(kHz) (kHz)

1920×1080

WUXGA

1920 × 1080

1920 × 1080 *

1920 × 1080

1920 × 1200

1920 × 1200 *

1920 × 1200

*

Compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).

59.9

49.9

60.0

60.0

50.0

49.9

59.9

60.0

49.9

60.0

59.9

59.8

49.9

50.0

60.0

60.0

60.0

72.0

75.0

84.8

50.0

59.8

59.9

74.9

84.9

60.0

50.0

49.8

59.9

100.0

120.0

49.9

59.9

60.0

74.9

60.0

66.3

72.0

75.0

85.0

47.7

39.6

54.1

64.0

65.2

65.3

78.8

82.2

55.9

71.6

60.0

52.4

64.0

72.3

78.2

80.0

91.1

46.3

75.0

65.3

54.1

55.6

66.6

67.2

61.8

74.0

74.6

37.1

44.8

76.3

92.6

39.6

47.8

47.4

60.3

68.6

41.3

49.7

49.3

62.8

PT-DS12K

Format Dot clock frequency

(MHz)

108.0

122.6

121.8

149.3

155.9

106.5

86.8

162.0

108.0

125.0

135.1

135.0

157.5

85.5

69.0

99.9

146.3

119.5

141.5

138.5

173.0

158.3

154.0

193.3

117.5

68.0

83.5

71.0

106.5

122.5

108.0

88.0

60.5

74.5

131.8

161.6

65.3

79.5

68.3

102.3

HDMI/DVI-D/RGB

RGB

HDMI/DVI-D/RGB

RGB

As of April 2013

SFD12M021

1 1 / 1 8

S

P E C

F

I L E

3-Chip DLP ™ Projector

PT-DS12K

List of compatible 3D signals

The 3D signals that can be input to this projector are shown in the table below.

Display mode

750 (720)/60p

750 (720)/50p

1125 (1080)/60i

1125 (1080)/50i

1125 (1080)/25p

1125 (1080)/24p

1125 (1080)/24sF

1125 (1080)/30p

1125 (1080)/60p

1125 (1080)/50p

VGA480

SVGA

XGA

MXGA

1280 × 720

1280 × 768

1280 × 800

MSXGA

SXGA

1366 × 768

SXGA+

WXGA+

UXGA60

WSXGA+

1920 × 1080

WUXGA

Display resolution

(dots)*

1

1280 × 720

1920 × 1080i

1920 × 1080

1920 × 1080i

1920 × 1080

640 × 480

800 × 600

1024 × 768

1152 × 864

1280 × 720

1280 × 768

1280 × 768

1280 × 800

1280 × 800

1280 × 960

1280 × 1024

1366 × 768

1400 × 1050

1440 × 900

1600 × 1200

1680 × 1050

1920 × 1080

1920 × 1080

1920 × 1200

1920 × 1200

*

*

3

*

3

*

3

3

Scanning frequency

H

(kHz)

53.7

37.1

44.8

76.3

92.6

39.6

47.8

47.4

67.5

56.3

31.5

37.9

39.6

48.4

81.4

98.8

45.0

37.5

33.8

28.1

28.1

27.0

27.0

33.8

41.3

49.7

49.3

60.0

52.4

64.0

47.7

39.6

54.1

64.0

65.2

65.3

55.9

46.3

75.0

65.3

54.1

55.6

66.6

61.8

74.0

V

(kHz)

60.0

50.0

60.0

50.0

25.0

24.0

48.0

30.0

60.0

50.0

59.9

60.3

50.0

60.0

100.0

120.0

60.0

49.8

59.9

100.0

120.0

49.9

59.9

60.0

50.0

59.8

59.9

60.0

50.0

60.0

59.8

49.9

50.0

60.0

60.0

60.0

59.9

49.9

60.0

60.0

50.0

49.9

59.9

49.9

60.0

Dot clock frequency

(MHz)

HDMI

Frame packing

Yes

Side by side*

2

Top and bottom

DVI

Side by side*

2

Top and bottom

Line by line

Yes Yes Yes Yes Yes

Frame sequential

71.0

108.0

88.0

108.0

85.5

69.0

99.9

108.0

74.5

131.8

161.6

65.3

79.5

68.3

68.0

83.5

148.5

148.5

25.2

40.0

51.9

65.0

113.3

139.1

81.6

60.5

74.3

74.3

74.3

74.3

74.3

74.3

74.3

74.3

122.6

121.8

106.5

86.8

162.0

146.3

119.5

141.5

138.5

158.3

154.0

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

*1 The “i” appearing after the resolution indicates an interlaced signal.

*2 Compatible with half-resolution signals.

*3 Compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).

As of April 2013

SFD12M021

1 2 / 1 8

S

P E C

F

I L E

3-Chip DLP ™ Projector

PT-DS12K

Display mode Display resolution

(dots)*

1

Scanning frequency

H

(kHz)

V

(kHz)

Dot clock frequency

(MHz)

RGB1/RGB2

750 (720)/60p

750 (720)/50p

1125 (1080)/60i

1125 (1080)/50i

1125 (1080)/25p

1125 (1080)/24p

1125 (1080)/24sF

1125 (1080)/30p

1125 (1080)/60p

1125 (1080)/50p

VGA480

SVGA

XGA

1280 × 720

1920 × 1080i

1920 × 1080

1920 × 1080i

1920 × 1080

640 × 480

800 × 600

1024 × 768

Side by side*

2

Yes

Top and bottom

Yes

Line by line

Yes

MXGA

1280 × 720

1280 × 768

1280 × 800

MSXGA

SXGA

1366 × 768

SXGA+

WXGA+

UXGA60

WSXGA+

1920 × 1080

WUXGA

1152 × 864

1280 × 720

1280 × 768

1280 × 768

1280 × 800

1280 × 800

1280 × 960

1280 × 1024

1366 × 768

1400 × 1050

1440 × 900

1600 × 1200

1680 × 1050

*

*

4

4

1920 × 1080

1920 × 1080 * 4

1920 × 1200

1920 × 1200 * 4

68.0

83.5

71.0

108.0

88.0

108.0

85.5

69.0

99.9

81.6

60.5

74.5

131.8

161.6

65.3

79.5

68.3

108.0

122.6

121.8

106.5

86.8

162.0

146.3

119.5

141.5

138.5

158.3

154.0

148.5

148.5

25.2

40.0

51.9

65.0

113.3

139.1

74.3

74.3

74.3

74.3

74.3

74.3

74.3

74.3

39.6

47.8

47.4

41.3

49.7

49.3

60.0

52.4

48.4

81.4

98.8

53.7

37.1

44.8

76.3

92.6

27.0

27.0

33.8

67.5

56.3

31.5

37.9

39.6

45.0

37.5

33.8

28.1

28.1

46.3

75.0

65.3

54.1

55.6

66.6

61.8

74.0

64.0

47.7

39.6

54.1

64.0

65.2

65.3

55.9

50.0

59.8

59.9

60.0

50.0

60.0

59.8

49.9

60.0

49.8

59.9

100.0

120.0

49.9

59.9

60.0

60.0

50.0

59.9

60.3

50.0

60.0

100.0

120.0

60.0

50.0

60.0

50.0

25.0

24.0

48.0

30.0

50.0

60.0

60.0

60.0

59.9

49.9

60.0

60.0

50.0

49.9

59.9

49.9

60.0

Yes

Yes

*1 The “i” appearing after the resolution indicates an interlaced signal.

*2 Compatible with half-resolution signals.

*3 SDI 1 only.

*4 Compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).

Yes

Yes

Yes

SDI1/SDI2

Frame sequential

Side by side*

2

– Yes

Top and bottom

Yes

Line by line

Yes

Yes*

3

Yes*

3

HDMI

& DVI

RGB1

&

RGB2

SDI1

&

SDI2

3G-SDI

Level B

Simultaneous

Simultaneous

Simultaneous

Simultaneous

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes*

3

As of April 2013

SFD12M021

1 3 / 1 8

S

P E C

F

I L E

3-Chip DLP ™ Projector

PT-DS12K

Serial connector

The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below.

Pin assignments and signal names

4

5

2

3

No.

1

Signal name

TXD

RXD

GND

D-sub 9-pin (female) Serial input

Description

NC

Send data

Receive data

NC

Ground

7

8

No.

6

9

Signal name

CTS

RTS

Description

NC

Connected internally

Connected internally

NC

Pin assignments and signal names

4

5

2

3

No.

1

Signal name

RXD

TXD

GND

D-sub 9-pin (male) Serial output

Description

NC

Receive data

Send data

NC

Ground

7

8

No.

6

9

Signal name

RTS

CTS

Description

NC

Connected internally

Connected internally

NC

Communication conditions (factory setting)

Signal level

Synchronization method

Baud rate

Parity

Character length

Stop bit

X parameter

S parameter

RS-232C-compliant

Start-stop synchronization

9,600 bps

None

8 bits

1 bit

None

None

Basic format

Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according to the details of control.

STX A D I1 I2 ; C1 C2 C3 : P1 P2 ... Pn ETX

Start

(1 byte)

(2 byte) Semicolon

(1 byte)

ID: 2 characters

(2 bytes)

01 to 64: Address number

0A to 0Z: Group ID

ZZ: All units (ID ALL)

Colon

(1 byte)

End

(1 byte)

Parameters

Command

(undefined length)

(3 bytes)

(Control and/or query commands)

ID designator

CAUTION

• It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then try sending or receiving again.

• When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next command.

• Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for command response to 10 seconds or more.

• When using two or more units:

1) Set different IDs for each unit.

2) Designate only one unit as RESPONSE (ID ALL) ON and the rest as RESPONSE (ID ALL) OFF.

3) Each group should have only one RESPONSE (ID GROUP) ON and the rest should be RESPONSE (ID GROUP) OFF.

As of April 2013

SFD12M021

1 4 / 1 8

S

P E C

F

I L E

3-Chip DLP ™ Projector

Cable specifications

PT-DS12K

Control commands

Command : Parameter

LPM:2

LPM:3

OLP:0

OLP:8

OLP:1

VSE:1

VSE:2

VSE:5

VSE:6

VSE:9

VSE:10

OPP:0

OPP:1

OPP:2

OPP:3

OAS

VPM:NAT

VPM:STD

PON

POF

OSH:0

OSH:1

IIS:SD1

IIS:SD2

IIS:HD1

IIS:DVI

IIS:RG1

IIS:RG2

IIS:VID

VXX:RYC1=+00000

VXX:RYC1=+00001

LPM:0

LPM:1

VPM:DYN

VPM:CIN

VPM:GRA

VPM:DIC

VXX:DLVI0=+00000

VXX:DLVI0=+00001

VXX:DLVI0=+00002

VXX:DLVI0=+00003

OTE:4

OTE:9

OTE:10

OTE:p1p2p3p4

TSD:y1y2y3y4m1m2d1d2w

TST:h1h2m1m2s1s2

OOS:0

OOS:1

Function

POWER (STANDBY)

SHUTTER

INPUT SELECT

RGB INPUT SETTING

LAMP SELECT

Lamp power

ASPECT RATIO

SWITCHING

P IN P SELECT

AUTO SETUP

PICTURE MODE

SYSTEM DAYLIGHT VIEW

COLOR TEMPERATURE

DATE

TIME

ON SCREEN

Standby power on

Standby power off

Shutter off

Shutter on

SDI 1

SDI 2

HDMI

DVI

RGB 1

RGB 2

Video

RGB/Y ・PB・PR

S-Video

Dual (two lamps)

Single lamp

Lamp 1

Lamp 2

High

Middle

Eco

Standard/VID Auto

4:3

16:9

HV fit

H fit

V fit

Off

User 1

User 2

User 3

Natural

Standard

Dynamic

Cinema

Graphic

DICOM

Off

1

2

3

User 1

User 2

Default

3200 K – 9300 K (100 K steps)

Date setting

Time setting

On-screen display off

On-screen display on

Callback

LPM:2

LPM:3

OLP:0

OLP:8

OLP:1

VSE:1

VSE:2

VSE:5

VSE:6

VSE:9

VSE:10

OPP:0

OPP:1

OPP:2

OPP:3

OAS

PON

POF

OSH:0

OSH:1

IIS:SD1

IIS:SD2

IIS:HD1

IIS:DVI

IIS:RG1

IIS:RG2

IIS:VID

VXX:RYC1=+00000

VXX:RYC1=+00001

LPM:0

LPM:1

VPM:NAT

VPM:STD

VPM:DYN

VPM:CIN

VPM:GRA

VPM:DIC

VXX:DLVI0=+00000

VXX:DLVI0=+00001

VXX:DLVI0=+00002

VXX:DLVI0=+00003

OTE:4

OTE:9

OTE:10

OTE:p1p2p3p4

TSD:y1y2y3y4m1m2d1d2w

TST:h1h2m1m2s1s2

OOS:0

OOS:1

* Do not send PON, POF, OSH, or OLP commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle.

* When a command that cannot be executed, the projector will send an ER401 command in reply.

As of April 2013

SFD12M021

1 5 / 1 8

S

P E C

F

I L E

3-Chip DLP ™ Projector

Status request commands

Command : Parameter

QPW

QSH

QIN

QSL

QLP

QPP

QPM

QVX:DLVI0

Function

Main power status

Shutter function status

Input signal status

Lamp operation mode status

Lamp power mode status

P in P status

Picture mode status

System daylight view status

Projector run time

Lamp 1 run time

Lamp 2 run time

Temperature status

Date setting status

Time setting status

On-screen display status

Callback

1

2

1

0

1

0

8

000

001

0

1

SD1

SD2

HD1

DVI-D

RG1

RG2

VID

0

3

NAT

STD

DYN

CIN

GRA

DIC

DLVI0=+00000

DLVI0=+00001

DLVI0=+00002

DLVI0=+00003 p1p2p3p4p5 p1p2p3p4 p1p2p3p4 p1p2p3p4/p5p6p7p8

* 1

QST

Q$L:1

Q$L:2

QTM:0

QTM:1

QTM:2

QGD

QGT

QOS

0

1 y1y2y3y4m1m2d1d2w h1h2m1m2s1s2

*1 p1p2p3p4: Celsius (°C), p5p6p7p8: Fahrenheit (°F)

*2 Day of week: Monday = 1, Tuesday = 2, ... Sunday = 7

*3 Set the date and time to UTC (universal time coordinated).

*

When a wrong command is sent, the projector will send an ER401 or ER402 command in reply.

PT-DS12K

Description

Off

On

Off

On

SDI 1

SDI 2

HDMI

DVI

RGB 1

RGB 2

Video

Dual (two lamps)

Single lamp

High

Middle

Eco

Off

User 1

User 2

User 3

Natural

Standard

Dynamic

Cinema

Graphic

DICOM

Off

1

2

3

00000h – 99999h

0000h – 9999h

0000h – 9999h p0 = Intake air p1 = Around lamp p2 = Optics module yyyymmdd (day of week)

* 2 hhmmss * 3

Off

On

Command example

To set the on-screen display off, send the command as shown below.

STX ADZZ ; OOS : 0 ETX

Start ID Address Command Parameter End

NOTE: When sending commands without parameters, a colon (:) is not necessary.

As of April 2013

SFD12M021

1 6 / 1 8

S

P E C

F

I L E

3-Chip DLP ™ Projector

PT-DS12K

Notes on projector placement and operation

The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions.

1. Never place objects on top of the projector while it is operating.

2. Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector’s exhaust openings.

3. Do not stack projector units directly on top of one another. If two units must be stacked for backup use in ordinary projection, use a method as shown below and provide ample space between the units to ensure that exhaust heat does not accumulate near the intake opening or around the units.

Dual stacked projection is not recommended.

4. Make sure that nothing blocks the projector’s air intake and exhaust openings. Also, install the projector so that cool or hot air from other air conditioning equipment does not flow directly toward the projector’s air intake or exhaust openings.

5. Do not install the projector in an enclosed space. If it is necessary to install it in an enclosed space, add a separate ventilation system. If ventilation is insufficient, hot air will accumulate at the intake opening. This may cause the projector’s protective circuit to interrupt projector operation.

6. If the projector is installed in an enclosed space, ensure that the temperature of the air surrounding the projector is between 0 °C and 45 °C (32 °F and 104 °F). Also make sure that the projector’s intake and exhaust openings are not blocked. Even though the air surrounding the projector is 40 °C

(104 °F) or less, if hot exhaust air accumulates inside the space, it may cause the projector’s protective circuit to interrupt projector operation. Pay particular attention to the surrounding temperature conditions when planning the installation.

7. If the projector is not to be set on the floor using adjuster legs, install it by using the five ceilingmount screw holes (screw diameter: M6, length of each screw hole in the projector: 16 mm (5/8˝)).

Provide a space of 5 to 10 mm (3/16˝ to 13/32˝) between the projector and the mounting surface by inserting metal spacers.

500 mm (19-11/16˝ ) or more

AUTO

SETUP

100 mm

( 3 -15 / 16 in) or more

500 mm (19-11/16˝ ) or more

500 mm (19-11/16˝ ) or more

AUTO

SETUP

AUTO

SETUP

Do not stack pr ojector units directly on top of one another.

Do not support the projector unit by its top while it is in use.

As of April 2013

SFD12M021

1 7 / 1 8

S

P E C

F

I L E

3-Chip DLP ™ Projector

Direction of air intake and exhaust

PT-DS12K

Intake

Exhaust

Operating the projector continuously

1. If the projector is to be operated continuously one week, use the dual-lamp optical system’s alternating lamp operation (lamp relay) function. The projector cannot be operated continuously one week in dual-lamp mode.

Allow a minimum of two hours per day of non-operation time for each lamp if the projector is to be operated continuously for more than one week.

2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.

Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.

Product availability differs depending on region and country. This product may be subject to export control regulations.

DLP and the DLP logo are trademarks of Texas Instruments.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

P JLink is a registered trademark, or a trademark application has been filed, in Japan, the United States, and other countries and regions.

All other trademarks are the property of their respective trademark owners.

As of April 2013

SFD12M021

1 8 / 1 8

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project