MG10LEDV/H - User’s Quick Reference Guide
K
EYPAD
O
VERVIEW
Partition 1 Status Partition 2 Status
Arm (red), Sleep (yel), Stay (grn):
On
Off
Flash
= Partition armed
= Partition disarmed
= Exit Delay
Fast Flash* = Exit Delay (final 10 sec.)
Fast Flash* = Partition in alarm
On = StayD
Mode Enabled
Off Light (red):
Off = armed
AC Light
On = Power on
Off = Power off
* Audible Indicators:
Continuous beep = Alarm
Variable beep = Fire alarm
Intermittent beep = Beginning of exit delay
Fast beep = Final 10 sec. of exit delay
Zone Display:
Keys [1] to [0(10)] correspond to zones 1 to 10 respectively.
Key Lit: Open or entry delay
Key Flash: In alarm
= Press once + [
CODE
MASTER
] for Quick Menu
Programming
[ TBL ] Trouble display
On = Trouble(s) occurring
[ MEM ] Alarm memory display
On = Alarm(s) occurred
[ BYP ] Bypass programming
On = Zone(s) bypassed
TO ARM
WHEN LEAVING
...
A
RMING AND
D
ISARMING
TO ARM
WHEN STAYING
...
To Regular Arm:
1. Close all zones in the desired partition.
2. Press [ ARM ].
3. Enter your [ ACCESS CODE ]*.
To Stay Arm:
1. Press the [ STAY ] key.
2. Enter your [ ACCESS CODE ]*.
To Sleep Arm:
1. Press the [
SLEEP
] key.
2. Enter your [
ACCESS CODE
]*.
To Disarm:
[
OFF
] + [
ACCESS CODE
]*
* If needed, press button(s) corresponding to desired partition(s). For two partitions, press the other key after the confirmation beep.
P
ANIC
A
LARMS
To send a silent or audible alarm to your Security Company, press and hold one of the button combinations listed for 3 seconds.
Panic Alarm Type Button
Combinations
Police
Medical
Fire
Press [1] & [3]
Press [4] & [6]
Press [7] & [9]
A
LARM
M
EMORY
D
ISPLAY
To view the alarms that occurred during the last armed period:
1. Disarm the system.
2. Press the [ MEM ] key.
3. The corresponding zone numbers that were in alarm the last time the system was armed will illuminate.
4. Press the [ CLEAR ] key to exit.
T
ROUBLE
D
ISPLAY
When a trouble condition occurs, the
[ TBL ] key will illuminate.
1. Press the [ TBL ] key. The key will flash and number(s) corresponding to the trouble(s) will illuminate.
2. Read the corresponding explanation from the trouble list in the MG5000 User Guide.
3. Press the [ CLEAR ] key to exit.
K
EYPAD
S
ETTINGS
To mute the keypad:
Press and hold the [ CLEAR ] key for 6 seconds to enable or disable Keypad Muting.
To modify the backlight:
1. Press and hold the [ MEM ] key for
3 seconds.
2. The [ MEM ] key will illuminate.
3. Press the [ MEM ] key to set the desired backlight level.
4. Press [ CLEAR ] or [ ENTER ] to exit.
B
YPASS
P
ROGRAMMING
Bypassed zones remained unarmed when the partition is armed.
1. Press the [ BYP ] key.
2. Enter your [
ACCESS CODE
]*.
3. The corresponding key of all open zones will illuminate. Select the zone(s) you want to bypass by entering the one-digit zone number. The zone key will flash.
4. Press the [ ENTER ] key to save and exit.
C
HIME
P
ROGRAMMING
A Chime Enabled zone will advise you every time it is opened by causing your keypad to beep.
1. Press & hold the corresponding zone key for 3 seconds (Accept beep = Chime enabled, Fail beep
= Chime disabled).
© Paradox Security Systems Ltd., 2005-2006.
Magellan is a trademark or registered trademark of Paradox Security Systems Ltd. and its affiliates in Canada, the United States and/or other countries. All rights reserved.
PARADOX.COM
Printed in Canada 04/2008 MG10LED-EQ03
