® Controls Reference Sheet

®
Controls
Reference Sheet
by
Please use this form as a reference. Controls must be ordered using the IntelliFlex Controls Planning Sheet or the
submittal form for the shade product being specified.
Draper Part
Number
Isolating Relay
Isolating Relay allows control of single shade—one isolating relay is used per motor. However, you can also daisy
chain up to 12 Isolating Relays, and control them using a single line 15 amp voltage (110-120V) switch. The
Isolating Relay can also be used if existing motors are failing due to inadequate pre-wired installations (i.e., not
enough wires pulled to motors). Operated by line voltage switch (SPDT only).
SC1
The SC1 is a smart, addressable control designed to operate one motor with four intermediate stops. Each SC1 is
an individually addressable and programmable single motor controller which hears commands from any number
of input devices (low voltage or Bus), interprets the command, and activates the appropriate relay to the group
of motors—through RJ11 (four-conductor) modular phone cable. BUS communications system allows parallel
connection of window shade motors and can be expanded later to include other control options. Fits in a deep
single gang box. Has a switching capacity of 6 amps. Can be operated by any IntelliFlex input device, and can
control several shade motors if each motor has an Isolating Relay.
C157.012
C156.065
GC4
Four 110-120V, single-motor electronic “isolating relays”, packaged in an 8" x 8" enclosure, the GC4 is an
inexpensive way of controlling multiple motors on a single switch. (Can be grouped together in banks of three,
to control up to 12 motors, operating on a standard, SPDT 15-amp switch.) Wires stay where they are meant to
through UL-recognized, spring-loaded connection terminals—providing for an extremely fast and easy installation.
Install individual relays to allow parallel wiring of multiple motors on one switch. This system does not allow for
control/adjustment of individual motors or mid-window alignment positions, and is not suitable if different fabrics or
tube diameters are being used in a single 4 motor panel. Can be operated by any IntelliFlex input device. UL listed
enclosure included.
SGC4
C156.058
C156.059
A low voltage control system, allowing control of up to 240 motors in groups of four motors, with six subgrouping
functions which can be changed through programming. Does not allow for adjustment of mid-window alignment
of individual shade motors, and is not suitable if different fabrics or tube diameters are being used in a single 4
motor panel. This unit is basically a GC4 (see above) packaged with an SC1 in an 8" x 8" enclosure. Brings down
the cost of controlling individual motors, while enabling “smart” communications via Bus communications system.
Suitable for commercial installations where individual motor control is not essential, but flexibility of control options
and subgroup control is desired. You can program from anywhere on the Bus: no access to the electrical panel is
required and there are no cumbersome DIP switches to set. In addition, you can program the SGC4 from many
sources: IR Wireless Remote Transmitters, RF Wireless Remote Transmitters, Hardwired Key Pads with built-in IR
receiver, RF Key Pads, RS232 systems and IP sources. Can be operated by any IntelliFlex input device. UL listed
enclosure included.
SPGC4
A low voltage control system allowing control of up to 60 motors individually, with four mid-window alignment stops,
six programmable subgrouping functions which can be changed through programming, and a myriad of grouping
possibilities. Combines SC1 capabilities to control individual motors, groups of motors or ALL motors through RJ11
(four-conductor) modular phone cable. Ideal for residential and commercial installations where individual motor
control is essential, as well as flexibility of control options and subgroup control. You can program from virtually
anywhere: no access to the electrical panel is required and there are no cumbersome DIP switches to set. Program
4 automatic stops and special IntelliFlex features from many sources: IR Wireless Remote Transmitters, RF
Wireless Remote Transmitters, Hardwired Key Pads with built-in IR receiver, RF Key Pads, RS232 systems and IP
sources. Can be operated by any IntelliFlex input device. UL listed enclosure included.
®
Copyright © 2009 Draper Inc.
Form IntelliFlex_RefSheet09
Printed in U.S.A.
C156.060
Page 2 of 4
IntelliFlex Reference Sheet by Draper
Draper Part
Number
Dry Contact Wall Switch
Clearly marked for intended function. Site-specific overlay may be provided. Only one button must be
activated per function. This input device can be used with the SC1, SGC4 or SPGC4.
Fully Programmable Bus Interface Wall Switch
Switch is clearly marked for intended function. Site-specific overlay may be provided. Only one button
must be activated for each function. Switch is capable of being reprogrammed to allow for various control
scenarios. Switch may act as a group switch, an individual motor switch or any combination thereof. This
input device can be used with SC1, SGC4 or SPGC4.
Various—see
Draper's
IntelliFlex Wall
Switch Selection Guide
Fully Programmable Bus Interface RF Wall Switch
Same as above, but sends RF signal. This input device can be used with SC1, SGC4 or SPGC4. You must
also select an RF receiver.
Wall Mountable Keypad (24 Channels)
OPEN
CLOSE
OPEN
1
ALL
2
8
3
C112.081
Only one button must be activated for each function. Keypad may act as a group control, an individual motor
control or any combination thereof. This input device can be used with SC1, SGC4 or SPGC4.
CLOSE
9
4
Wall Mountable Keypad (12 Channels)
10
5
11
6
C112.083
Same as above, but 12 channels. This input device can be used with SC1, SGC4 or SPGC4.
12
7
STOP
RF Keypad (24 Channels)
C112.080
Same as above, but RF, and 24 channels. This input device can be used with SC1, SGC4 or SPGC4. You
must also select an RF receiver.
RF Keypad (12 Channels)
C112.082
RF Keypad (6 Channels)
C112.084
24 Channel Combination RF/IR Remote Control Transmitter
C072.014
Same as above, but 12 channels.
9
10
1
ST
OP
The transmitter is clearly marked for intended function, and shall send signals simultaneously via RF and IR.
Only one button must be activated for each function. May act as a group control, an individual motor control
or any combination thereof. This input device can be used with SC1, SGC4 or SPGC4. You must also select
an IR Eye or RF Receiver.
7
6
5
4
3
12
11
2
OPE
N
CL
OSE
8
AL
L
OPE
N
CL
OSE
Same as above, but 6 channels.
12 Channel Combination RF/IR Remote Control Transmitter
C072.015
Same as above, except 12 channels.
6 Channel Combination RF/IR Remote Control Transmitter
C072.016
Same as above, except 6 channels.
RF Remote Control Receiver
C081.017
Listens for a unique security code from the transmitter. Each receiver can learn up to 5 transmitter codes.
Multiple units can be installed on the Bus, extending the effective range of an RF system. Can be set up
to listen to commands from a number of sources including: RF transmitters, RF Key Pads, RF Transmitter
modules (that can send commands from Sun and Wind sensors or RS232 interfaces). One unit controls
up to 60 motors. This input device can be used with SC1, SGC4 or SPGC4. You must also select an RF or
combination IR/RF transmitter.
RF Long Range Antenna
C267.001
Replaces standard antenna to increase transmitter operation distance from receiver.
DC Power Supply for wireless Serial Interface
C258.002
Power supply converts 115V AC to 5V DC for RF operation of Transmitter and RS232 Serial Interface.
Wall Entry Plate
Designed to assist in pre-wiring. Pre-wire one per specified motor; when it's time to hook up the motors, just
plug them in.
www.draperinc.com
(765) 987-7999
C079.061
Page 3 of 4
IntelliFlex Reference Sheet by Draper
Draper Part
Number
10
1
12
C072.017
5
4
ST
OP
3
11
2
12 Channel IR Remote Control Transmitter
7
6
OP
EN
9
CL
OS
E
8
AL
L
OP
EN
CL
OS
E
24 Channel IR Remote Control Transmitter
May act as a group control, an individual motor control or any combination thereof. This input device can be
used with SC1, SGC4 or SPGC4. You must also select an IR Eye.
C072.018
Same as above, except 12 channels.
6 Channel IR Remote Control Transmitter
C072.019
Same as above, except 6 channels.
IR Remote Control Eye on 6' Modular Cable
C081.013
Tiny IR eye designed to peek out from behind a surface. 72" white modular cable provided. One eye connected to a Bus allows control of up to 60 motors. Dimensions of black part of eye: ¼" x ¼" x ¼". This device
can be used with SC1, SGC4 or SPGC4. You must also select an IR or combination IR/RF transmitter.
IR Remote Control Eye on 2' Modular Cable
C081.012
Same as above, but the length of white modular cable is 24".
IR Remote Control Eye in Plastic Box
C081.014
IR eye in a white box is designed to be wall mounted. The length of white modular cable is determined at the
job site and can be up to 100 feet. One eye connected to a Bus could allow for control of up to 60 motors.
Dimensions: 2" x1¼" x ¾". This device can be used with SC1, SGC4 or SPGC4. You must also select an IR
or combination IR/RF transmitter.
IR Remote Control Eye for J-Box with Lens
C081.015
IR eye is to be single gang junction box mounted, and appears as part of the existing junction boxes at a
project. The length of white modular cable is determined at the job site and can be up to 100 feet. A violet,
decora sized IR lens is included. One eye connected to a Bus could allow for control of up to 60 motors.
This device can be used with SC1, SGC4 or SPGC4. You must also select an IR or combination IR/RF
transmitter.
IR Remote Control Eye/SC1 J-Box Mounting Kit
C081.016
Junction box mounting kit for locating a single SC1 into a single gang junction box. Includes IR eye,
hardware and Decora sized violet IR lens. This device can be used with SC1. You must also select an IR or
combination IR/RF transmitter.
Switch
EYE
BUS
RS232
Red = Program Mode
Green = Visible Light
(Test Mode Only)
Wind Disable Light
Input Switch Sensor
PSSW
Programmable Sun Sensor with Box
C156.057
Sensor shall automatically control individual shade or groups of shades in response to the position of the
sun. This input device can be used with SC1, SGC4 or SPGC4.
Magnetic Lockout Switch
C112.085
Install at a door or window to provide SPST maintained contact back to SC1 motor control. When closed,
the SC1 operates; when open, the window treatment is opened. Adjustable cord length. Attach to Open and
Common terminals of the manual inputs. This input device can be used with SC1, SGC4 or SPGC4.
Multi Control Input Adapter for up to 2 Eyes and 2 Receivers
C103.043
Used when the number of “Eye” ports are insufficient to power all of the devices within a given SC1
system. Allows for 2 devices to be added to a Bus. Connects via “Main” to any “Eye” within a system. Aux
connections to as many as two SC1 motor controls.
Serial Port Adapter
Converts a standard DB9 serial output of a PC into an RJ11 connection providing RS232 serial commands.
www.draperinc.com
(765) 987-7999
C103.042
Page 4 of 4
IntelliFlex Reference Sheet by Draper
Mounting Bracket for SC1
C002.490
Allows installation of SC1 in North American deep single gang junction box (2" x 4" x 3¼").
PSI60 Bus Command Converter (for Dry Contact Input)
C112.086
Converts simple Dry Contact button press and outputs as an SC1 Bus command.
R2D7 RS232 Professional Integration Interface
Tech
2
7 vsimple
R2gyDmade
nolo
SYS 4
SYS 53 RS-232
SYS 6
SYS 71 SYS 2 SYS
SYS
MAIN
C156.066
Acts as additional Bus system input device allowing a facilities manager to send commands to shade
motors at any time to position shades appropriately for maximum utility and efficiency. Includes free "GUI"
software capable of scheduling timed events and global alignment positioning of shades. This input device
can be used with SC1, SGC4 or SPGC4.
USB-to-DB9 Serial Port Converter
C103.049
Serves as a bridge between USB port and standard RS232 Serial Port.
LS100 Internet Protocol Interface Device
Ethernet to Serial bridge device to control R2D7 via Ethernet. Comes with its own power supply and
instructions. The LS100 can have a static IP address assigned to it, allowing for direct access to any device
connected to it via Ethernet connection. This input device can be used with SC1, SGC4 or SPGC4.
Modular Jack Adapter
C103.045
Modular Jack Adapter for four wires converts any size wire into an RJ11 connection.
Modular Cable Coupler
C131.022
For use in extending a wire used in a Bus, this white coupler connects standard phone cable together and
keeps the wires correct. CAUTION: similar looking parts at retail stores look the same, however they flip the
wires: if used in a Bus installation will disable the Bus and kill the system.
RJ15 Modular Connector
C079.054
Standard (6 pin connectors) modular plug. Commonly known as RJ15.
Three-System Master Control Splitter
Allows for the isolation of motor controls in up to three systems. Local control sources may be installed
allowing a user to have local control only, at the same time a MASTER control location can be installed
allowing that Master location only control of the entire system. Small RJ11 part—4 jacks.
LCD Timer
CAL CLK PGM AUTORAND MAN
OFF
AM
PM
12:00 d
MO TU WE TH FR SA SU ON
MODE
NEXT/
ON/
OFF
RESET
DAY/
DST
HOUR+
YEAR-
M+
ZONEYEAR-
The timer acts as a “normally open” (NO) switching device. This delivers a closed contact in the “On Mode,”
and an open contact in the “Off Mode.” The timer may be set to deliver up to seven (7) On/Off setting pairs.
Each setting pair can be set to activate: everyday, once a week, every weekday or weekends only. The timer
can be used as a local switch. The timer is capable of many other features (including: Astronomic Feature,
Automatic Daylight Savings Time adjustment, Random Operation feature, and much more).
www.draperinc.com
(765) 987-7999
C156.062
Download PDF