Station
User Guide
Including Attendant Features
STARPLUS STS
Telephone Systems
Station User Guide
December, 2002 - Issue 1.0
P/N: 3552-00
I
Issue
Release
Date
1.0
12-02
Changes
Initial Release
LIFE SUPPORT APPLICATIONS POLICY
VODAVI Technology, Inc. products are not authorized for
and should not be used within Life Support applications.
Life Support systems are equipment intended to support or
sustain life and whose failure to perform when properly
used in accordance with instructions provided can be
reasonably expected to result in significant personal injury
or death.
VODAVI Technology, Inc. warranty is limited to
replacement of defective components and does not cover
injury to persons or property or other consequential
damages.
Copyright © 2002 VODAVI Technology, Inc.
All Rights Reserved
This material is copyrighted by VODAVI Technology, Inc. Any
unauthorized reproductions, use or disclosure of this material,
or any part thereof, is strictly prohibited and is a violation of
the Copyright Laws of the United States (17 U.S.C. Section 101
et. seq.).
VODAVI reserves the right to make changes in specifications
at any time and without notice. The information furnished by
VODAVI in this material is believed to be accurate and reliable,
but is not warranted to be true in all cases.
STARPLUS and STS are registered trademarks of
VODAVI Technology, Inc.
mj/2002
Vodavi STS Telephone Systems
FIXED FEATURE BUTTONS
•
•
•
•
•
•
CAMP ON Button -- Enables you to alert a busy
party that an outside line is on hold and waiting
for them.
CONF (CONFERENCE) Button -- Used to
establish and build conference calls.
FLASH Button -- Used to terminate an outside
call and restore dial tone without having to
hang up the handset. It is also used to transfer
calls behind a PBX or Centrex within those
systems.
FWD (FORWARD) Button -- Allows you to
forward your calls to another station.
HOLD Button -- Enables you to place an outside
caller on hold.
H-T-P Switch -- Allows the user to select the ICM
signaling mode: Handsfree, Tone, or Privacy.
Quick Reference Card
•
•
•
•
•
•
MSG (MESSAGE WAIT) Button -- Allows you to
initiate a message waiting indication at stations
that are busy, unattended, or in Do Not Disturb.
Message Waiting Callback request left at your
station is indicated by a flashing MSG WAIT LED.
MUTE Button -- Allows you to switch the builtin microphone on or off when using the
speakerphone, or the handset microphone
when using the handset.
ON/OFF Button -- Enables you to make a
telephone call without lifting the handset. It
turns the telephone on and off when using the
speakerphone.
SPEED Button -- Provides you with access to
speed dialing, save number redial and last
number redial. This button is also used to
access flexible button programming.
TRANS (TRANSFER) Button -- Used to transfer
an outside call from one station to another.
VOLUME BAR -- Allows the user to adjust
speakerphone and handset volume.
CALL FORWARDING
UNSCREENED TRANSFER
1. Press the FWD button or dial [640].
2. Dial the desired Call Forward code:
[6] = All Calls
[7] = No Answer
[8] = Busy
[9] = Busy/No Answer
3. Dial station number where calls are to be
forwarded. Confirmation tone sounds.
4. Replace handset or press ON/OFF button.
1. Press TRANS button and dial station number.
2. When the called extension begins to signal,
hang up to transfer the call.
3. Replace handset or press ON/OFF button.
ESTABLISHING A CONFERENCE
Only stations that have Conference enabled will be
able to initiate a Conference.
1. Lift the handset.
2. Select intercom station or dial desired outside
party. When called party answers, press the
CONF button.
3. Add next conference party by selecting
another outside line or intercom station.
4. Press the CONF button again and repeat
previous step in a cycle, until all parties are
contacted.
5. When last party answers, press the CONF
button twice. All parties are connected.
TERMINATING A CONFERENCE
To terminate a Supervised Conference, the conference initiator, replaces handset or presses ON/OFF
button.
To terminate an Unsupervised Conference, press
the flashing CONF button while on-hook.
SCREENED TRANSFER
While connected to an outside line:
1. Press station button where call is to be
t ra n s f e r r e d ( i f pr o g ra m m e d o n y ou r
telephone),
-orPress the TRANS button and dial the desired
station number.
(The called extension signals according to the
intercom signal switch position.)
2. When that extension answers, announce the
transfer.
3. Hang up to complete transfer.
LEAVING A MSG WAITING INDICATION
If you dial a station that is busy, unattended, or in
Do Not Disturb, you can leave a message waiting
indication.
1. Press the ON/OFF button.
2. Dial the desired intercom station. A busy tone
or DND tone is heard.
3. Press the MSG button. The called party’s MSG
button LED will flash slowly.
4. Press the ON/Off button to end the call.
Quick Reference Card
Vodavi STS Telephone Systems
PLACING AN OUTSIDE LINE ON HOLD
To transfer a call using Directory Dialing
•
1. Press the TRANS button.
2. Dial Directory Dial Code [680],
-orPress the DIRECTORY DIAL flexible button.
3. Press the digit associated with the person’s
name. When the name displays, press the
SPEED button to automatically dial the station.
4. Press the ON/OFF button to complete transfer.
Calls may only be transferred to internal stations.
•
If your system is programmed for Exclusive
Hold Preference, press the HOLD button once
for Exclusive Hold or twice for System Hold.
If your system is programmed for System Hold
Preference, press the HOLD button once for
System Hold or twice for Exclusive Hold.
STORING SPEED NUMBERS
1. Press the SPEED button twice.
2. Dial the speed bin location.
• 9000 to 9019 = Station Speed numbers
• 9020 to 9099 = System Speed numbers
3. Dial desired telephone number.
4. Press the SPEED button.
5. Press the ON/OFF button to end speed dial
programming.
To clear an existing speed bin:
1. Press the SPEED button twice.
2. Dial the speed bin location.
3. Press the SPEED button again. Confirmation
tone sounds.
DIALING A SPEED NUMBER
1. Press the SPEED button and dial the speed bin
location,
-orPress preprogrammed speed bin button.
• 9000 to 9019 = Station Speed numbers
• 9020 to 9099 = System Speed numbers
2. When called party answers, pick up handset or
use speakerphone.
DIRECTORY DIALING
Users with display telephones may view a list of
individuals on the telephone system and have the
system automatically dial that person. Directory
Dialing may also be used to transfer a call from one
station to another.
1. Dial the Directory List dial code [680],
-orPress the DIRECTORY DIAL flexible button.
2. Press a button on the keypad once, twice, or
three times, to represent the letter of the
alphabet, to begin viewing the list of names.
3. Scroll through the Directory List to select a
name as follows:
• Press [. ] to scroll up to next entry,
-or• Press [#] to scroll down to previous entry.
4. Press the SPEED button at the desired name to
automatically dial the destination station or
outside phone number (via Speed Dial).
PROGRAMMING FLEXIBLE BUTTONS
1. Press the SPEED button twice.
2. Press the flexible button to be programmed.
3. Dial the desired code from the following chart.
Confirmation tone sounds.
4. Press the ON/OFF button.
All Call Page (Internal & External)700
Background Music
632
Call Back
622
Call Park Location (System)
43+[C]
Call Park Location (Station)
439+[XXX]
Call (Park) Pickup
#6+[XXX]
Caller ID Review (Answered)
659
Caller ID Review (Unanswered) 635
Directory Dial
680
Do Not Disturb
631
Extension Numbers
100-149
External Page Zone
761
Last Number Redial
[SPEED]+[#]
Line Queue
621
Personal Park
438
Speed Dial Access
[SPEED]+[YYYY]
Save Number Redial
[SPEED]+[.]
VM Group Pilot Numbers
44 [V]
________________________________________
C = Call Park Location (0-7)
V = Voice Mail Group Number (0-7)
XXX = Station Extension Numbers
YYYY = Speed Dial Bin Numbers
(9000-9019 Station) (9020-9099 System)
To erase a flexible button:
1. Press the SPEED button twice.
2. Press the flexible button to be erased.
3. Press the FLASH button. Confirmation tone
sounds.
4. Press the ON/OFF button.
December, 2002
i
Contents
About This User Guide.............................................................. 1
911 Alert...................................................................................... 2
Account Codes ......................................................................... 3
Using Account Codes...................................................... 3
Verified Account Codes.................................................. 3
Account Codes - Traveling COS (Verified) ............... 4
Answering Machine Emulation .......................................... 5
Notification Methods ...................................................... 5
Attendant Features................................................................. 7
Attendant Clear Alarm.................................................... 7
Attendant CO Line External (Off-Net) Forward ..... 7
Attendant Custom Message......................................... 8
Attendant Day/Night/Special ...................................... 9
Attendant Directory List Programming ................... 10
Attendant Disable Outgoing CO Line....................... 13
Attendant Override ......................................................... 14
Attendant Setting Time and Date .............................. 14
Attendant Speed Dial - System Storing ................... 15
Attendant Unavailable ................................................... 16
Attendant Voice Mail Alarm Clear .............................. 16
Background Music (Optional) ............................................. 17
Call Back ...................................................................................... 18
Call Coverage ............................................................................ 19
Call Forward............................................................................... 20
Call Forward - External (Off-Net)................................. 21
Call Forward - Follow Me............................................... 22
Call Park....................................................................................... 24
Call Park - Personal........................................................... 24
Call Park - Station ............................................................. 25
Call Park - System ............................................................. 26
ii
December, 2002
Call Pickup.................................................................................. 28
Directed Call Pickup ........................................................ 28
Group Call Pickup............................................................. 29
Call Transfer ............................................................................... 30
Executive/Secretary Transfer ....................................... 30
PBX/Centrex Transfer...................................................... 30
Screened Transfer ............................................................ 31
Transfer Search.................................................................. 31
Unanswered CO Call Transfer ...................................... 32
Unscreened Transfer ....................................................... 32
Caller ID Display ....................................................................... 32
Caller ID Display (Answered Calls).............................. 32
Caller ID Display (Unanswered Calls) ........................ 33
Caller ID Name/Number ....................................................... 34
Calling Forward Override...................................................... 34
Calling Station Handsfree Mode Override...................... 35
Calling Station Tone Mode Override................................ 35
Camp On..................................................................................... 36
CO Line - Access ....................................................................... 37
CO Line Queue.......................................................................... 38
Conference................................................................................. 39
Conference Combinations............................................ 39
Conference Procedures.................................................. 39
Dial-By-Name ............................................................................ 42
Directory Dial ............................................................................ 43
Do Not Disturb.......................................................................... 45
Executive Override.................................................................. 47
Flash ............................................................................................. 47
Flash Key on Intercom .................................................... 47
Flexible Button Programming ............................................ 48
Group Listening ....................................................................... 49
Headset Mode .......................................................................... 49
December, 2002
Intercom ..................................................................................... 51
Using an Intercom Button ............................................ 51
Answering an Intercom Call ......................................... 52
Intercom Transfer............................................................. 52
Intercom Calls.................................................................... 53
Keyset Mode.............................................................................. 54
Last Number Redial................................................................. 55
LCR Operation........................................................................... 56
Loop Key ..................................................................................... 57
Mailbox Buttons....................................................................... 57
Message Wait ............................................................................ 58
Modem ........................................................................................ 59
Voice Mail Modem Access............................................. 59
Telephone System Modem Access ............................ 59
Mute ............................................................................................. 60
Name In Display ....................................................................... 60
Night Service ............................................................................. 61
Off-Hook Voice Over (OHVO) .............................................. 62
Outside Calls.............................................................................. 64
Placing an Outside Line on Hold ................................ 64
Answering a Recall........................................................... 64
Answering an Outside Call............................................ 64
Placing an Outside Call................................................... 64
Paging.......................................................................................... 65
Paging - Meet Me ............................................................. 66
Personalized Messages.......................................................... 66
Pre-assigned Messages .................................................. 66
Custom Messages ............................................................ 67
Date and Time Entry Messages ................................... 68
Scrollable Canned Messages........................................ 70
Personal Messages Flexible Button ........................... 71
PBX/Centrex Codes on a Flex Button ............................... 72
iii
iv
December, 2002
Release Button.......................................................................... 72
Redial ........................................................................................... 72
Last Number Redial ......................................................... 72
Save Number For Redial ................................................ 73
Redial a Saved Number.................................................. 73
Repeat Redial .................................................................... 73
Ring Down / Hot Line / Off-Hook Preference ................ 74
Ring Tone ................................................................................... 76
School Zone............................................................................... 77
Software Version...................................................................... 79
Speakerphone .......................................................................... 79
Speed Dial .................................................................................. 80
System Speed Dial Access............................................. 82
Station/Port Fixed Number.................................................. 82
Station Relocate ....................................................................... 83
Text Messaging (Silent Response)..................................... 83
Uniform Call Distribution...................................................... 85
UCD Calls In Queue Display.......................................... 85
UCD Available/Unavailable Mode.............................. 85
UCD Overflow Station Forward................................... 86
Universal Day/Night Answer ............................................... 87
Voice Mail ................................................................................... 87
Call Forwarding to Voice Mail Groups ...................... 87
Retrieving Voice Messages ........................................... 88
Voice Mail Transfer with ID Digits .............................. 88
Voice Mailbox Button ..................................................... 88
Voice Mail Group Button ............................................... 89
Voice Mail Group Access................................................ 89
Voice Mail One-Touch Recording............................... 89
Voice Mail (Flash-Based) Quick Reference...................... 91
Quick Start for First-Time Users .......................................... 92
Volume Control ........................................................................ 93
December, 2002
Worksheets ................................................................................ 95
Flexible Button Programming Worksheet .............. 95
Speed Dial Bin Programming Worksheet................ 95
Default Numbering Plan ....................................................... 96
v
vi
December, 2002
Digital Telephone Features
2
18
1
19
3
9
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PRS
TUV
WXY
7
8
9
OPER
*
0
8
FLASH
TRANS
SPEED
CONF
MSG
FWD
MUTE
CAMP ON
ON/OFF
HOLD
6
7
5
4
#
10
11
12
VOLUME
13
16
17
15
14
Digital Key Telephone Buttons
Number
Feature
Description
1
Display
Displays information about telephone
status, dialing directories, and text
message information.
2
Message
Indicator
Programmable indication for Ring Line,
Voice Mail, Message Wait, or handset
operation.
December, 2002
vii
Digital Key Telephone Buttons
Number
Feature
Description
3
Flexible Button
Keys
Used to access outside lines or access
call-handling features.
4
MSG Key
Used for Auto-CallBack to a phone that has
left a text message or to access voice
messages.
5
FWD Key
Used to forward your calls to another
station or voice mail.
6
SPEED Key
Used to access speed dialing, save number
redial, and last number redial. Buton is also
used to access flexible button
programming.
7
CONF Key
Used to establish conference calls.
8
TRANS Key
Used to transfer an outside call from one
station to another.
9
FLASH Key
Used to end an outside call and to restore
dial tone without hanging up receiver.
10
CAMP ON Key
Used to alert a busy station that an outside
line is on hold and waiting for them.
11
MUTE Key
Used to activate/deactivate MUTE
function. When activated, the party on the
other end cannot hear you.
12
HOLD Key
Used to hold calls or to retrieve held calls.
13
ON/OFF Key
Used to make a call without lifting the
handset.
14
VOLUME Key
Used to adjust level of tones, background
music, ringing, receiver volume, and
display contrast.
15
Speaker
Outputs tones and voice at your extension.
16
Microphone
Used to talk with other party without using
the handset.
17
HPT
Used to select mode of operation:
Handsfree, Privacy, or Tone.
18
Interactive Soft
Keys
Used to work in conjunction with fixed and
flexible features.
19
Headset Jack
2.5 mm Headset Jack is located on the left
side of the telephone.
» » » » » » » » NOTES » » » » » » »
1
ABOUT THIS USER GUIDE
The features described in this User Guide apply to Vodavi
STS Digital and Vodavi Single Line Telephone Systems.
GUIDELINES
Flexible Buttons -- Most system features can be set up on a
flexible button for easy one-button access. (For more details,
refer to “Flexible Button Programming” on page 48.)
This “Flex Btn” symbol indicates those features that
need a preprogrammed button to function properly.
- EXCEPTION When the “Soft Key” symbol is also present, use of
either a preprogrammed button or a Soft Key is
permitted.
Soft Key
Flexible Numbering -- This feature allows the system
numbering plan to be modified, as well as the length of the
feature access codes (2-4 digits).
For consistency, the following programming and operating
procedures refer to “3-digit” default codes.
To verify the numbering plan for your system, consult
with your System Administrator.
Single Line Telephones -- A “telephone” symbol
appears when the Single Line Telephone (SLT)
operation differs from the Digital Telephone.
If your SLT has a FLASH key … use that key instead
of “depressing the hookswitch” when instructed.
SLT
2
911 Alert
911 Alert
Any station user or attendant who programs a flexible button
for 911 ALERT (feature code 608) will be alerted of internal
stations placing 911 calls. The system can store the 16 most
recent 911 calls. Calling information includes the time/date of
the call and the station number from which the call was placed.
The initial 911 Alert indications include:
Audible ringing tone
Green flashing 911 ALERT flexible button LED
Automatic LCD display of 911 call information
E 9 1 1 C AL L
M M / DD / Y Y
XX:
S TA X X XX
HH:MM
XX = Index number (01-16)
Station users and attendants can press the flexible button as
necessary to view additional 911 call information in the stored
list. Once a station user or attendant views the information for
all 911 calls in the system list:
LEDs at all stations will change to a solid red indication.
Audible ringing tone at all stations ceases.
LCDs at all stations will revert to a normal display.
The list remains available for review by pressing the 911
ALERT flexible button until all messages are deleted.
To delete logged 911 Alert messages:
An attendant must use the following steps to delete the
messages on a system-wide basis.
1. Press the 911 ALERT flexible button to display the 911
call information for deletion.
2. Press FLASH to delete that message.
Dialing 911 from any station overrides previously
enabled features such as Do Not Disturb.
Account Codes
3
Account Codes
Using Account Codes
Prior to placing, or during, an outside line call:
1. Press the preprogrammed ACCOUNT CODE button (627).
2. Dial account code up to 12 digits. (The other party does not
hear the digits being dialed).
If account code is less than 12 digits, an [.] must be
entered to return to the call.
If account codes are forced, the account code must be
entered prior to dialing the outside number.
3. Dial [9] or CO Access code. A dial tone will sound.
4. Dial the desired number.
Verified Account Codes
Prior to placing an outside line call:
1. Press the preprogrammed ACCOUNT CODE button (627).
2. Dial account code up to 12-digits.
To
1.
2.
3.
SINGLE LINE TELEPHONE
enter an Account Code before a call:
Lift the handset.
Dial [627].
Dial the account code.
.
If the account code contains fewer than 12 digits, dial [ ]
to automatically return to the call.
4. Dial [9] or CO Access code. A dial tone will sound.
5. Dial the desired number.
4
Account Codes
To enter an Account Code during a call:
1. Depress the hookswitch momentarily. Call is placed on
executive hold while you enter your account code.
2. Dial [627].
3. Dial the account code.
.
If the account code contains fewer than 12 digits, dial [ ]
to automatically return to the call.
Account Codes - Traveling COS (Verified)
To use Verified Account Codes:
1. Press preprogrammed ACCOUNT CODE button (627) before
accessing a CO line.
2. Dial account code up to 12-digits. If account code matches
a verified account code, intercom dial tone is returned.
Otherwise an error tone is presented.
3. Access an outside CO line, or dial the LCR code, and then
dial the desired number.
To
1.
2.
3.
SMDR must be enabled for the Account Code
feature to operate, and become part of the SMDR
record.
SINGLE LINE TELEPHONE
enter an Account Code before a call:
Lift handset.
Dial [627].
Dial account code.
If Account Code contains fewer than 12 digits, dial
[ ] to return to intercom dial tone.
.
4. Dial [9] or CO Access code. A dial tone will sound.
5. Dial desired number.
Answering Machine Emulation
5
Answering Machine Emulation
When a call is sent to your voice mailbox, you can press a
preprogrammed flexible button to listen to the caller leaving
the voice mail message. If you decide to speak with the caller,
you can press the preprogrammed button to be connected to
the caller.
Notification Methods
There are two methods of notification, a Ring Mode or a
Speaker Mode. These methods are controlled by the type of
flexible button assigned on the telephone.
The preprogrammed button type (654+0=Ring Mode,
654+1=Spkr Mode) defines the operation mode. An incoming
CO call rings at a station and forwards (except busy type) to the
station’s VM mailbox.
Ring Mode
The preprogrammed flexible button flashes red while the caller
is in your mailbox. You can press the flashing button and the
audio is broadcast over the speaker of the keyset. The MUTE
key is also enabled and the LED lights solid green. When the
call is ringing the station in the ring mode, the display shows:
S CR E E N IN G R I N G
M M M DD Y Y
H H : M M am
6
Answering Machine Emulation
Speaker Mode
The VM message is broadcast over the speaker. The MUTE key
is enabled and the LED lights solid green. When the station is
monitoring the caller in VM, the display shows.
S CR E E N IN G
M M M DD Y Y
H H : M M am
MAILBOX Options
The Mailbox Owner can select from the following options when
a call is sent to their voice mailbox.
To leave caller in VM and turn off speaker:
Press the ON/OFF button and continue to listen to message
being left without taking action at the keyset. After the VM
message is left, the preprogrammed button will be solid red
and the keyset will return to idle.
To talk to party leaving the message:
Press the MUTE key. Station is still in CONF and caller can
hear VM and you.
To pick up call:
Press the flexible button. When the call is picked up, the
voice mail system will disconnect from the call.
Attendant Features
7
Attendant Features
If your station is designated as the attendant station, the
following features are available to assist you in efficiently
operating your telephone.
Attendant Clear Alarm
The attendant can dial feature code [606] to clear any T-1 alarm.
This function does not clear the condition, only the display.
Attendant CO Line External (Off-Net) Forward
To activate off-net forwarding:
1. Dial [603] on the dial pad,
-orPress the preprogrammed CO OFF-NET FORWARD button.
2. Dial the CO group access code of group to be forwarded:
[801-823] = CO Group 1-23
[824] = All CO Groups
3. Dial the speed bin number that contains the number where
calls are to forward. A confirmation tone will sound.
To cancel off-net forwarding:
1. Dial [603] on the dial pad,
-orPress preprogrammed CO OFF-NET FORWARD button.
2. Dial the CO group access code.
3. Dial [#] on the dial pad. A confirmation tone will sound.
8
Attendant Features
Attendant Custom Message
Program the ten custom messages for system-wide use at the
first Attendant station as follows:
1. Dial the Custom Message program code [694] on the dial
pad. The following message displays:
ENTER MSG NO
MMM DD YY
H H :M M a m
2. Enter a valid message bin number [21–30]. The following
message displays after the bin number has been selected.
m m m m m m m m m m . ..
ENTER MSG:
3. Enter the letters for the custom message using the dial pad
keys as shown:
Other Codes
1
A - 21
B - 22
C - 23
D - 31
E - 32
F - 33
G - 41
H - 42
I - 43
J - 51
K - 52
L - 53
M - 61
N - 62
O - 63
P - 71
R - 72
S - 73
Q - 74
T - 81
U - 82
V - 83
W - 91
X - 92
Y - 93
Z - 94
0PER
*
0
1 = 1#
8 = 8#
“ = 01
* = *#
2 = 2#
9 = 9#
, = 02
( = #1
3 = 3#
0 = 0#
? = 03
) = #2
4 = 4#
Space = 11
/ = 04
+ = #3
5 = 5#
: = 12
! = *1
= = #4
6 = 6#
- = 13
$ = *2
# = ##
7 = 7#
‘ = 14
& = *4
. = 24
#
Up to 24 alphanumeric characters may be entered
(represents 48 digits). Characters display when entered.
Attendant must go idle after programming a message
before another message may be programmed.
4. Press the HOLD button to enter the message. A
confirmation tone will sound.
Attendant Features
Attendant Day/Night/Special
9
OR
The system’s Automatic Night Mode Feature can be overridden
by the Attendant station. Any Attendant station user can press
their DND button or a Soft Key to place the system into Night
Mode.
The Night Service feature provides a means to put the
system in night mode or remove the system from
night mode from any keyset, providing the system
was put in night mode by the night service feature
flexible button [604].
If the system was placed in night mode by the
Attendant using the DND button or if the system was
placed in night mode by the automatic schedule, the
night service flexible button cannot remove the
system from night mode.
To use this feature:
1. Press the preprogrammed NIGHT SERVICE button (631, DND
by default) once to activate the Night mode or use the Soft
Key’s DND option when in an idle condition (LED is lit solid).
2. Press the DND button or Soft Key again to activate the
Special mode (LED flashes).
The DND button (by default) or Soft Key acts as a rotary
in this manner, starting in the Day mode, Night mode,
and Special mode.
When one Attendant activates this mode, other
Attendant stations’ DND buttons are lit accordingly.
10
Attendant Features
Attendant Directory List Programming
The Attendant can program up to 200 names in the directory
list. When the directory list is accessed by any display
telephone user, the system displays the name associated with a
speed dial number so when the desired name is shown, the
user may then have the system dial the number.
To access Directory List Programming:
Dial the Directory List program code [693].
The HOLD button will illuminate and the first entry (000) in
the Directory List will display:
D I R LS T A A A B I N/ IC M : XX X X
n nn nn nn nn n nn nn nn nn nn nn n
AAA = Directory List entry number (000-199)
XXXX = One of the following:
» 3- or 4-digit station number (100-8999)
» 3-digit local number/name translation table number
(600-799 minus station numbers that would overlap)
» 4-digit system speed bin number (9020-9099)
nnn = Programmed Name (blank, if none)
Directory List
The following procedure is used to enter, edit, and erase names
in the Directory List for stations or speed dial numbers.
To modify the Directory List:
1. Enter desired 3-digit Directory List number (000-199), or
dial [.] to scroll up (next entry) or [#] to scroll down
(previous entry) through the list.
If changing a name already associated with an existing
station, skip to step 4.
2. Press TRANS.
Attendant Features
11
3. Enter the 3- or 4-digit station intercom number.
4. Press the MUTE button.
5. Enter the name (up to 24 characters may be entered) by
using the keys. The display updates as the name is entered.
Other Codes
1
A - 21
B - 22
C - 23
D - 31
E - 32
F - 33
G - 41
H - 42
I - 43
J - 51
K - 52
L - 53
M - 61
N - 62
O - 63
P - 71
R - 72
S - 73
Q - 74
T - 81
U - 82
V - 83
W - 91
X - 92
Y - 93
Z - 94
0PER
*
0
1 = 1#
8 = 8#
“ = 01
* = *#
2 = 2#
9 = 9#
, = 02
( = #1
3 = 3#
0 = 0#
? = 03
) = #2
4 = 4#
Space = 11
/ = 04
+ = #3
5 = 5#
: = 12
! = *1
= = #4
6 = 6#
- = 13
$ = *2
# = ##
7 = 7#
‘ = 14
& = *4
. = 24
#
6. Press SPEED when finished. Confirmation tone sounds and
the display shows the new or changed name.
7. Press HOLD, then use [.] or [#] to scroll to next entry.
-orHang up to end programming.
To
1.
2.
3.
clear an entry:
Select the desired entry.
Press TRANS., then press FLASH.
Press SPEED, a confirmation tone will sound and entry is
erased.
12
Attendant Features
Local Translation Table
The following procedure is used to associate names to the
Local Number/Name Translation Table number only.
To add names to Local Translation number:
1. Enter desired three-digit Directory List number (000-199),
or dial [.] to scroll up (next entry) or [#] to scroll down
(previous entry) through the list.
If changing a name already associated with an existing
Table entry, skip to step 4.
2. Press TRANS.
3. Dial three-digit Local Number/Name Translation Table
number (600-799) that represents the desired telephone
number.
4. Press MUTE.
5. Use keys on the dial pad to enter the name (up to
24 characters may be entered). The display updates as the
name is entered.
If an error is made during keystroke entry, press
FLASH to clear the current name.
6. Press SPEED when finished. Confirmation tone sounds and
the display shows the new or changed name.
7. Press HOLD, then use [.] or [#] to scroll to next entry.
-orHang up to end programming.
Attendant Features
13
Speed Dial Bin
The following procedure is used to associate names to a system
speed dial bin only.
To add names to a System Speed Bin:
1. Enter desired 3-digit Directory List number (000-199), or
dial [.] to scroll up (next entry) or [#] to scroll down
(previous entry) through the list.
If just changing a name associated with an existing System
Speed Dial Bin entry, skip to step 4.
2. Press TRANS.
3. Dial system speed dial bin location (9020-9099).
4. Press MUTE.
5. Use keys on the dial pad to enter the name (up to
24 characters may be entered). The display updates as the
name is entered.
6. Press SPEED when finished. Confirmation tone sounds and
the display updates.
7. Press HOLD, then use [.] or [#] to scroll to next entry.
-orHang up to end programming.
Attendant Disable Outgoing CO Line
The first Attendant can disable CO lines to prevent outgoing
access to those lines.
To
1.
2.
3.
disable CO Lines:
Lift handset or press ON/OFF button.
Dial [602] on the dial pad. A confirmation tone will sound.
Press the line button(s) of the CO Line(s) to disable. The CO
Line button(s) LED flashes; a confirmation tone sounds.
To reactivate the CO Line(s):
Repeat Steps 1-3 to disable this feature.
14
Attendant Features
Attendant Override
When Attendant Override is enabled, Attendant stations may
override or call stations that are busy or in Do Not Disturb.
To call a station busy on a CO call:
Press the preprogrammed ATTN OVERRIDE button [601].
Three short tone bursts are presented to the called party.
After five (5) seconds, the station’s CO line is automatically
placed on hold and the Attendant is cut-through.
To call a station in Do Not Disturb mode:
Press the preprogrammed ATTN OVERRIDE button. The
station is signaled with a Camp On tone.
Attendant Setting Time and Date
System Time/Date must be set by the first programmed
Attendant via admin programming or using feature code 692.
To set using the feature code:
1. Dial [692] on the dial pad. A confirmation tone will sound.
2. Enter date and time as follows: YYMMDDHHMM
YY = Year (00-99)
MM = Month (01-12)
DD = Day (01-31)
HH = Hour (00-23)
MM = Minute (00-59)
When the correct number of digits are entered, a
confirmation tone will sound.
3. Press the ON/OFF button to OFF to update the display.
Attendant Features
15
Attendant Speed Dial - System Storing
System Speed numbers must be entered by the first
programmed Attendant. If an Attendant is not specified, enter
at Station 100.
1. Press SPEED once, then press the desired outside line key,
-orPress SPEED twice to select an outside line automatically.
2. Dial the System Speed bin location (9020-9099).
3. Dial telephone number.
4. Press SPEED.
5. Hang up.
Speed Dial Options
To use the following speed dial options, enter as shown:
Initiate a Pulse-To-Tone
Switchover
Press TRANS during number entry.
Insert a Pause
Press HOLD during number entry.
Insert a Flash into the
Speed Number
Press FLASH.
Insert a Non-Display
Character
Press TRANS as the first entry in the
speed bin.
This causes the numbers stored in the
bin not to display on the Digital
Telephones when the bin is accessed.
Speed Bin numbers 9060-9099 are not monitored by
Toll Restriction.
16
Attendant Features
Attendant Unavailable
The Attendant Unavailable feature lets Attendant stations have
a button that places their station in an Unavailable Mode.
When the station is in the Unavailable Mode, the next
Attendant station receives dial “0” calls and recalls.
To activate Unavailable Mode:
As the (first programmed) Attendant …
Press the preprogrammed UNAVAILABLE flexible button,
-orDial the Attendant Unavailable code [607] on the dial pad,
and the following results occur:
The flexible button LED will light solid, if programmed.
Recalls and dial “0” calls will ring at the second
Attendant’s station.
If the second Attendant places their phone in
unavailable, the third Attendant will receive recalls and
dial “0” calls.
To deactivate Unavailable Mode:
As the (first programmed) Attendant …
Repeat activation process shown above (press Unavailable
button or dial code 607), the following results will occur:
The flexible button LED, if programmed, will extinguish.
The First Attendant will resume normal operation.
The Second and third Attendants will not receive recalls
or dial “0” calls.
Attendant Voice Mail Alarm Clear
The Attendant display shows an alarm condition when the
system detects that the digital voice mail is out of service.
Dial feature code [656] to clear any alarm from the display.
This function does not clear the condition, only the display.
Background Music (Optional)
17
Background Music (Optional)
To activate Background Music,either:
1. Dial [632] or press the preprogrammed BGM flexible button,
then enter [1] on the keypad.
-orUse the Soft Key’s BGM option as a toggle.
0 : OF F
1 : CH -1
M M M DD Y Y
H H :M M a m
A confirmation tone will sound, and the music is audible
through the speaker.
2. Press Volume Bar to change the volume. The LCD displays:
S PEA K E R B G M [ ### ## ### #]
M M M DD Y Y
H H : M M am
To deactivate Background Music:
1. Dial [632] again or press BGM flexible button, then enter [0].
-orUse the Soft Key’s BGM option as a toggle.
2. A confirmation tone will sound and the music will
discontinue.
SINGLE LINE TELEPHONE
The Background Music feature is not compatible with Single
Line Telephones.
18
Call Back
Call Back
A station can initiate a call back request to another busy
station. Once that station becomes idle, the station that left the
call back request is signaled.
To leave a Call Back request when a number is busy:
1. Press the preprogrammed CALL BACK flexible button or use
the Soft Key’s CALL-BK option.
2. Replace the handset or press the ON/OFF button. When the
busy station hangs up, you will be signaled.
3. Answer the call; the station you called will then be signaled.
(If your station is busy when signaled, an automatic MSG
will be placed at your phone.) Only one Call Back request
can be left at a station; the second request will leave a
message wait callback request.
When the Automatic Call Back Timer is enabled, a
call back request is automatically invoked anytime
you listen to a busy intercom tone for a preset
period of time (default = 3 seconds).
SINGLE LINE TELEPHONE
To leave a Call Back request when a number is busy:
1. Briefly depress and release the hookswitch.
2. Dial [622] and replace the handset.
Only one Call Back request can be left at a station;
the second request will convert to a message
waiting request.
Call Coverage
19
Call Coverage
The Call Coverage feature provides the functionality for
stations to answer calls for other stations by utilizing call
coverage buttons. Visual and Audible status of ringing stations
to an assigned coverage station are provided.
To
1.
2.
3.
assign a Call Coverage Button:
Press [SPEED] + [SPEED].
Press a desired flexible button.
Dial [647] for Non-Ringing or [646] for Ringing, followed by
the station number to cover. A confirmation tone will
sound.
After button is assigned, and that station receives a call:
1. You will receive audible and/or visual indications after a
programmable period of time: an internal ring tone, and/or
the same flash rate as the incoming CO line ringing rate.
Ringing option = ringing, flashing Call Coverage LED,
LCD display as in following illustration:
C A LL F O R S TA X X X X
M M M DD Y Y
H H :M M a m
Non-Ringing option = flashing Call Coverage LED only
(no ringing or change to LCD)
2. Then press the flashing COVERAGE flexible button,
-orPress the ON/OFF button.
The call is answered and will cease to ring at any other
stations that may have the same coverage appearance.
20
Call Forward
The following message displays after the call is answered.
C A LL F O R S TA X X X X
F R O M S TA Y Y Y Y
H H :M M a m
SINGLE LINE TELEPHONE
This feature can cover SLT extensions, however an SLT cannot
perform the call coverage function. The SLT extension need
not be physically installed, only the SLT card must be installed.
Call Forward
The Call Forward feature allows a station the ability to have
calls (internal or external) forwarded to a designated station, a
UCD group pilot number, Voice Mail group number, or Hunt
group. This feature must be enabled in admin programming.
To activate Call Forwarding:
1. Lift the handset or press the ON/OFF button, press the FWD
button or dial [640], then dial the appropriate forwarding
condition code.
[6] = All Calls
[8] = Busy
[7] = No Answer
[9] = Busy/No Answer
-orUse the applicable Soft Key’s ALL-FWD, N/A-FWD, BSY-FWD,
or B/NA-FWD option.
2. Press the DSS button of desired station,
-orDial the desired extension number where to forward calls,
including UCD, Voice Mail, Hunt Group pilot numbers and
Speed Dial bins for off-net forwarding.
3. Replace the handset or press the ON/OFF button.
Call Forward
21
To remove Call Forwarding:
1. Lift handset or press ON/OFF button.
2. Either press the FWD button, dial [640] or [662], or use the
Soft Key’s CLR-FWD option. A confirmation tone sounds
and the FWD LED extinguishes.
SINGLE LINE TELEPHONE
The SLT operation uses the same procedures as the Digital
Telephone, except there is no FWD button or Soft Keys. You
must use feature codes 640 and 662.
Call Forward - External (Off-Net)
Stations are allowed to forward intercom and transferred CO
line calls to an off-net location. The Call Forward Off-Net feature
allows a station to reroute calls that would normally be lost.
Calls can be forwarded to home or another off-net site. Initially
ringing CO calls cannot be forwarded with this feature.
To
1.
2.
3.
activate Off-Net Call Forwarding:
Lift the handset or press the ON/OFF button.
Press the FWD button or dial [640] on the dial pad.
Dial [.] on the dial pad. Dial the speed bin number
(9000-9019 or 9020-9099) that contains the number where
calls are to be forwarded. A confirmation tone will sound
and the FWD button LED is flashing.
4. Replace the handset or press the ON/OFF button.
To remove Off-Net Call Forwarding:
1. Lift the handset or press the ON/OFF button.
2. Press the FWD button or dial either [640] or [662]. A
confirmation tone sounds and the FWD LED extinguishes.
SINGLE LINE TELEPHONE
The SLT operation uses the same procedures as the Digital
Telephone, except there is no FWD button. The user must use
the 640 feature code to activate and 662 to clear.
22
Call Forward
Call Forward - Follow Me
The Follow Me feature lets a user who is away from their
station, activate/deactivate call forwarding from another
station in the system. This lets the user forward their calls to
their current location or into Voice Mail, UCD, Hunt Groups, any
other station in the system, or to an off-net location. When this
call forward is activated, all calls presented to the forwarded
station forward to the destination station immediately.
To
1.
2.
3.
activate Follow Me Call Forwarding:
Lift the handset or press the ON/OFF button.
Dial the Follow Me Forward code [642] on the dial pad.
Dial station number of the station from which forwarding is
desired.
4. Dial the appropriate forwarding condition code.
[6] = All Calls
[8] = Busy
[.] = Off-Net
[7] = No Answer [9] = Busy/No Answer
5. Dial the three- or four-digit destination number where calls
are to be forwarded. (Station, Voice Mail, UCD, Hunt Group,
or speed bin (only for off-net)).
6. Replace the handset or press the ON/OFF button.
To
1.
2.
3.
remove Follow Me Call Forwarding:
Lift the handset or press the ON/OFF button.
Dial the Follow Me Forward code [642] on the dial pad.
Dial the station number of the station that forwarding is to
be cancelled.
4. Dial [6] (regardless of the forward condition).
5. Redial the same station number. Confirmation tone sounds
and FWD LED extinguishes.
Call Forward
23
To establish Follow Me Call Forwarding (off-site location):
1. Dial into the system on a DISA or TIE trunk. Enter the DISA
access code, if applicable.
2. Dial the Follow Me Forward code [642] on the dial pad.
3. Dial the station number of the station from which
forwarding is desired.
4. Dial the appropriate forwarding condition code.
[6] = All Calls
[8] = Busy
[.] = Off-Net
[7] = No Answer [9] = Busy/No Answer
5. Dial the three- or four-digit destination number where calls
are to be forwarded (System Speed Bin (off-net only),
Station, Voice Mail, UCD, or Hunt Groups). A confirmation
tone sounds; five seconds later a dial tone is received.
To remove Follow Me Call Forwarding (off-site location):
1. Dial into the system on a DISA or TIE trunk. Enter the DISA
access code, if applicable.
2. Dial the Follow Me Forward code [642] on the dial pad.
3. Dial the station number of the station that forwarding is to
be cancelled.
4. Dial [6] (regardless of the forward condition).
5. Redial the same station number. Confirmation tone sounds;
5 secs later = dial tone.
24
Call Park
Call Park
Call Park - Personal
Each digital telephone in the system can place a call into a
personal park location and then later retrieve that call from the
originating station. Intercom calls and CO line calls can be
placed into the stations’ personal park location. Calls parked in
a personal park location are subject to the system call park
recall timer. A station retrieving a personal parked CO call must
have either a direct CO line appearance or an available loop
button to retrieve the parked call.
To park a call, while connected to an outside line:
1. Press the TRANS button. The caller is put on Exclusive Hold.
2. Dial the Personal Park location [438] on the dial pad,
-orPress the preprogrammed PERSONAL PARK button. A dial
tone will sound.
To retrieve a Parked Call:
Dial Personal Call Park location code [438] on the dial pad,
-orPress the preprogrammed PERSONAL PARK button. A talk
path will be established between the two parties.
SINGLE LINE TELEPHONE
While connected to first call:
1. Depress the hookswitch momentarily. An intercom dial
tone will sound.
2. Dial [438]. The call is placed in personal park.
3. Dial desired number for second call.
Call Park
25
4. Depress the hookswitch momentarily. An intercom dial
tone will sound.
5. Dial [438]. The first call is returned and the second call will
be placed into personal park.
The user can alternately connect to the other call
by doing a hook flash and dialing [438] as many
times as necessary.
Call Park - Station
Call Park (by station number) allows calls to be parked at a
station other than you own, thus allowing for expanded park
locations.
To
1.
2.
3.
create a CALL PARK (Station) button:
Press [SPEED] + [SPEED].
Press the desired flexible button.
Dial [439] + [#]. A confirmation tone sounds.
26
Call Park
While connected to an outside line:
1. Press the TRANS button.
2. Dial [439] + [XXX] (XXX = station number).
-or1. Press the TRANS button.
2. Press the preprogrammed CALL PARK (Station) button.
3. Dial [XXX] (XXX = station number).
To retrieve a Call Park (Station) call:
Dial [#6] + [XXX] while at any telephone in the system,
including the initiator’s. [XXX] = the station number used to
park the call.
-orDial [438] from the initiator’s station.
SINGLE LINE TELEPHONE
The SLT operation uses the same procedures as used in
Digital Telephone operation described above, except there is
no TRANS button. The user must use 438 and hookflash 439
feature codes.
Call Park - System
An outside line can be placed into one of eight parking
locations and can be retrieved by any station that has a direct
line appearance or an available Loop button. Parked calls have
their own recall timer that recalls the originating station, and if
still unanswered, the Attendant(s).
An outside line may also be placed into a station park location.
The station user then dials a code followed by their station
number to retrieve the call.
Call Park
27
To consult, page, or call an internal party while connected
to an outside line:
1. Press the TRANS button, or press the CALL PARK flexible
button. The caller will be put on hold.
2. Dial the parking location (430 to 437), or press the
preprogrammed CALL PARK flexible button. A confirmation
tone will sound.
3. If a busy tone is received, press TRANS twice and dial
another park location, or press the CALL PARK flexible
button for a different parking location.
To
1.
2.
3.
retrieve a Parked Call,either:
Lift the handset or press the ON/OFF button.
Press [#].
Dial the parking location (430 to 437) where the call was
parked, or press the preprogrammed CALL PARK flexible
button.
-orUse the Soft Key’s PK-PICK1 option when in an idle condition
(to pick up group 1 only).
SINGLE LINE TELEPHONE
To place an outside call on hold and consult with, page, or
call an internal party before transferring the outside call:
1. Depress and release the hookswitch. The caller is put on
Exclusive Hold.
2. Dial parking location (430-437). A confirmation tone will
sound.
3. If busy, depress and release hookswitch twice, dial another
park location, then hang up.
To retrieve a parked call:
1. Lift the handset and press the [#] button.
2. Dial parking location (430 to 437) where call was parked.
28
Call Pickup
Call Pickup
A station can pickup a call ringing to any specific unattended
station by using the Directed Call Pickup procedure.
A station can pickup a call ringing to an unattended station
within the same UCD group by using the Group Call Pickup
Procedure.
Directed Call Pickup
To create a Pickup Button:
1. Press [SPEED] + [SPEED].
2. Press the desired flexible button, then dial #0.
To use Directed Call Pickup:
1. Dial the station number of the known ringing telephone.
Receive ringback tone or call announce tone depending on
the intercom selector switch setting.
2. Press the preprogrammed PICKUP button to answer the call.
To
1.
2.
3.
SINGLE LINE TELEPHONE
use Directed Call Pickup:
Lift the handset.
Dial [#1].
Dial station number of ringing telephone.
You MUST have access to the specific outside line
or a LOOP button to do a directed call pickup.
Call Pickup
29
Group Call Pickup
To
1.
2.
3.
create a Pickup Button:
Press [SPEED] + [SPEED].
Press the desired flexible button.
Dial #0.
To use Group Call Pickup:
1. Lift the handset or press the ON/OFF button.
2. Dial [#0] on the dial pad,
-orPress preprogrammed PICKUP button to connect to calling
party.
SINGLE LINE TELEPHONE
To use Group Call Pickup:
1. Lift the handset.
2. Dial [#0]. You will be connected to the incoming intercom
or outside line call.
You must be in the same Pickup group as the
ringing telephone to pickup the call.
You MUST have access to the specific outside line
or LOOP button to use Group Call Pickup.
30
Call Transfer
Call Transfer
Outside lines can be transferred from one phone to another
within the system. The transfer can be either screened
(announced) or unscreened to either an idle or busy station, a
UCD Group, or a Hunt Group.
Executive/Secretary Transfer
If you are designated the Executive station and your phone
is busy or in DND, all calls will be routed to the Secretary
station.
If you are the designated Secretary station, you can signal
the Executive that is busy or in DND by using the Camp On
feature.
PBX/Centrex Transfer
While connected to an outside line (PBX/Centrex):
1. Press FLASH. The transfer dial tone will be heard.
2. Dial the PBX/Centrex station number.
3. Hang up to complete the transfer.
SINGLE LINE TELEPHONE
To make a PBX/Centrex Transfer:
1. Briefly depress and release the hookswitch. An intercom
dial tone will sound.
2. Dial [660]. A Flash command is presented to the PBX or
Centrex CO Line (a stutter tone will sound).
3. Dial the desired telephone number.
4. Replace the handset to complete transfer.
Call Transfer
31
Screened Transfer
To conduct the transfer, while connected to an outside line:
1. Press the station button where call is to be transferred (if
programmed on your telephone) or press TRANS and dial
station number.
The called extension signals according to the intercom
signal switch position.
2. When that extension answers, announce the transfer.
3. Hang up to complete the transfer.
To answer the Screened Transfer:
Your intercom will be signaling according to the intercom
signal switch position.
1. Answer the intercom and receive the transfer notice.
2. Press OUTSIDE LINE or flashing LOOP button on hold.
If the Direct Transfer feature is enabled, the
screened transfer will go directly to the handset.
You do not have to press a LINE or LOOP button to
answer.
Transfer Search
When attempting to locate a party:
1. Press a station DSS button to signal the station or press
TRANS and dial desired station.
2. If the station is unavailable, press another station DSS
button to enter a new station number or press TRANS twice
and dial the station number.
3. When the station answers, hang up to complete transfer.
32
Caller ID Display
Unanswered CO Call Transfer
While idle or on an internal/external call and an incoming or
transferred CO call is ringing at your station:
1. If on another call, place the current call on hold and replace
the handset or press ON/OFF.
2. Dial the INC CO XSFR code [639] or press preprogrammed
INC CO XSFR flexible button.
3. Press a DSS, Group button, or dial a station or group
number. Call automatically transfers to that destination.
4. You can then return to the call placed on hold.
Unscreened Transfer
1. Press the TRANS button.
2. When the called extension begins to signal, hang up to
transfer the call (the Recall Timer start).
3. Replace the handset or press ON/OFF.
Caller ID Display
Caller ID Display (Answered Calls)
The Answered Caller ID Table feature can store up to
100 system-wide entries of the most recently answered calls
with caller ID. A station may dial a unique access code to view
the entries, scroll through the entries, and dial a desired entry
back. The table displays the caller ID number and the identity of
the station that answered the call.
This table may be accessed from any user station display
phone. Any Attendant station can delete a table entry, one
entry at a time.
To start the review process at the beginning of the table:
Dial [659].
Caller ID Display
33
Caller ID Display (Unanswered Calls)
An Unanswered Call Management Table with 100 system-wide
entry capacity is maintained in the system. The calling number/
name information pertaining to any unanswered call is placed
in this table at the time the system determines the call was
abandoned.
This table may be accessed from any display telephone to
review unanswered calls. Only an Attendant station(s) can
delete an entry from this table.
To start the review process at the beginning of the table:
Dial [635].
Keypad Functions
The following functions apply to both Answered and
Unanswered Call Management Tables:
Function
Button
Review next item in table entry
MUTE
Step to next table entry
HOLD
Delete table entry (Attendant only)
FLASH
Exit table review function
ON/OFF
Step to previous table entry
TRANSFER
Call Back
SPEED
34
Caller ID Name/Number
Caller ID Name/Number
This feature allows you to program a flexible button [653] to
view both the number and name on the LCD when receiving a
Caller ID CO call. When the feature is enabled, the flexible
button LED is lit solid and the name and number is displayed.
During the call, press the flexible button to toggle between the
normal call information display and the name/number display.
The top line of the LCD displays the number of the caller and
the bottom line of the LCD displays the name.
Calling Forward Override
The Call Forward Override feature allows a user to reach a busy
station that is call forwarded. This allows the calling station to
override the forwarding which allows the user to use Off Hook
Voice Over (OHVO), Executive Override, Monitor, Message Wait
Indication, Camp On, or Call Back Request at that station rather
than forwarding to another destination.
1. Dial [5#] followed by the desired station extension.
2. Press the appropriate preprogrammed button.
Call Back = [622]
Camp On = [620]
Executive Override = [625]
Message Wait = [623]
OHVO = [628]
Calling Station Handsfree Mode Override
35
Calling Station Handsfree Mode Override
This feature enables a calling station to override a called
station’s T intercom setting.
When placing a call to a station and handsfree is desired:
1. Dial [7#] on the dial pad.
2. Dial the extension number,
-orPress the DSS button of desired station (call connects to the
station in a handsfree mode).
Calling Station Tone Mode Override
This feature enables a calling station to override a called
station’s H or P intercom settings.
When placing a call to a station and tone ringing is desired:
1. Dial [6#] on the dial pad.
2. Dial the extension number,
-orPress the DSS button of the desired station (call tone rings
station).
36
Camp On
Camp On
OR
A station may alert a busy party that an outside line is on hold
and waiting for them by using the CAMP ON button.
To camp on a call, press the TRANS button to transfer the call to
the desired busy station, then press the CAMP ON button.
The busy party will receive a muted ring over the keyset
speaker, and a visual flashing CAMP ON LED. By pressing the
CAMP ON button, the person called places their existing
outside call on hold and is connected to the person placing the
Camp On. They can then pick up the call on the appropriate
line.
To alert a busy station of your call:
1. Press the CAMP ON button or use the Soft Key’s CAMP-ON
option. The called station will receive one burst of ringing.
2. When the called party answers, consult with them or hang
up to transfer call.
If a station is in DND, only the Attendant can Camp
On using the Attendant override feature. Camp On
or Override drops any internal callers to which
that station is talking.
To answer a call that is waiting:
1. Press your flashing CAMP ON button when you hear one
burst of muted ringing. Any outside line you are connected
to will be placed on hold.
2. Converse with the station placing the call,
-orIf a call is being transferred, press the flashing OUTSIDE
LINE button.
CO Line - Access
37
SINGLE LINE TELEPHONE
To alert a busy station of your call:
1. Briefly depress and release the hookswitch.
2. Dial [620]. When the called line is alerted, they can choose
to pick up your call or remain on original call.
To answer a call that is waiting (while on a CO line call):
1. Receive Camp On warning tone through the handset.
2. Choose desired call (hang up on present call and take new
call, or ignore Camp On signal).
CO Line - Access
To access an outside line:
1. Press an idle CO line button or a POOL button,
-orDial a CO line group access code or an LCR code: 9, 801-823,
88+LLL (LLL = CO Line number).
2. Dial the desired number for outside call.
3. Lift the handset to converse or use the speakerphone.
To
1.
2.
3.
SINGLE LINE TELEPHONE
access an outside line:
Lift the handset.
Dial access code: 9, 801-823, 88+LLL (LLL = CO line number).
Dial telephone number.
38
CO Line Queue
CO Line Queue
If you wish to be placed on a waiting list for an outside line
to become available:
1. Press desired busy OUTSIDE LINE button,
-orPress the POOL button. (A busy tone will sound.)
2. Press the preprogrammed CO LINE QUEUE button (621).
3. Replace the handset or press the ON/OFF button.
To answer a queue:
If you hear ringing and an outside line of the line group or a
LOOP button you queued onto is rapidly flashing:
1. Lift the handset or press the ON/OFF button.
2. Press the flashing OUTSIDE LINE button, or LOOP button.
To cancel a call back request:
1. Dial the CO Line Queue Cancel code [626] on the dial pad.
2. Replace handset or press ON/OFF button.
SINGLE LINE TELEPHONE
1. Dial an outside line access code, a busy tone will sound.
2. Briefly depress and release the hookswitch.
3. Dial [621]. A confirmation tone will sound.
Conference
39
Conference
Conference Combinations
Only stations that have conference enabled can institute a
conference.
Add-On Conference -- Up to eight internal parties can
engage in a conference, or seven internal parties with one
external party. A maximum of five 8-party conferences (five
external parties maximum) can be established.
Multi-Line Conference -- One internal station can engage in
a conference with up to four outside parties.
A maximum of eight parties can be included in a
conference.
Conference Procedures
To
1.
2.
3.
4.
establish a Conference:
Lift the handset.
Select an intercom station or dial desired outside party.
When called party answers, press the CONF button.
Add the next conference party by selecting another
outside line or intercom station, or by using the Soft Key’s
ADD MEM option.
5. If the next conference party is an outside line and a busy or
wrong number is encountered, press one of the conference
parties on hold. This drops the busy or wrong number
party. Press the conference button again and repeat step 4.
6. When the last party answers, press the CONF button twice.
(All parties will be connected.)
40
Conference
To exit a Conference (controller only):
For a Single-line conference …
1. Press the ON/OFF button to ON.
2. Press the MUTE button, then replace the handset to
monitor the conference.
For a Multi-line conference …
1. Press the HOLD button to place outside parties on hold.
The Hold Timer starts. If one of the two parties is internal,
that party is dropped.
2. Either press CONF and hang up or press the ON/OFF button
or use the Soft Key’s EXIT option to leave the other
conference parties still connected in an unsupervised
conference. The CONF button flashes and the timer starts.
There is a warning tone before the other parties are
dropped.
To re-enter a Conference:
When the controller re-enters the conference, the disconnect
timer is reset.
1. Lift the handset to re-enter a monitored conference.
2. To re-enter a conference placed on hold, repeat steps for
establishing a conference.
3. To re-enter an unsupervised conference, lift the handset
and press the flashing CONF button or use the Soft Key’s
RE-ENTER option. The CONF button will light steady and a
confirmation tone will sound.
To terminate a Conference, the conference initiator who is
actively in the conference must:
Replace the handset or press the ON/OFF button to OFF.
To terminate an Unsupervised Conference:
Press the flashing CONF button or use the Soft Key’s END
option while on-hook, all parties will be dropped.
Conference
To
1.
2.
3.
4.
41
terminate a party during a Conference call:
Press the line button of the party you wish to drop.
Replace the handset or press the ON/OFF button.
Lift the handset or press the ON/OFF button.
Press the flashing CONF button.
SINGLE LINE TELEPHONE
To set up a Conference with one external and one other
internal station:
1. Place an outside call.
2. Briefly depress and release the hookswitch to put the call
on hold.
3. Dial the number of the internal station you wish to add.
4. When that station answers, briefly depress and release the
hookswitch again. All three parties will be connected.
To set up a Conference with Personal Park:
1. While connected to an outside line, depress the hookswitch
momentarily. The intercom dial tone will sound.
2. Dial [438]. The first call will be placed in personal park.
3. Dial the desired number for the second call.
4. Depress the hookswitch momentarily. The Intercom dial
tone will sound.
5. Dial the code for SLT Conference Park [664]. All three parties
will be conferenced.
6. Hang up to terminate the conference.
42
Dial-By-Name
Dial-By-Name
The system allows station users to dial extension numbers, or
speed bins, by entering the name of a person that has been
programmed for that station.
The system database allows entry of a name (alphanumeric) up
to 24 characters in length for each station. The programmed
name can be used for dial-by-name station users and in
directory dialing.
(NOTE … This feature should not be confused with the Name In
Display function.)
1. Dial the Dial-By-Name
code [6.] on the dial pad,
-orPress the preprogrammed
DIAL-BY-NAME flexible
button.
2. Dial the person’s last name
on the keypad as shown.
1
A-2
B-2
C-2
D-3
E-3
F-3
G-4
H-4
I-4
J-5
K-5
L-5
M-6
N-6
O-6
P-7
R-7
S-7
Q-7
T-8
U-8
V-8
W-9
X-9
Y-9
Z-9
OPER
#
0
Example …
To search for the name BROWN, press [2] [7] [6] [9] [6].
*
When the system finds a numeric match for the name
being dialed:
A call will be placed to the station matching the name.
An intercom call will signal the station according to the
intercom mode selected: H, T, or P.
If fewer than 8 digits are dialed, the numeric match is
dialed after a 10-second interdigit time-out occurs, or
when the [#] key is pressed.
Directory Dial
43
Directory Dial
Display telephone users may view a list of up to 200 names
from the System Directory on the station’s LCD display. You can
dial the station or speed dial bin by pressing a single button.
Names placed in the Directory List may be associated to
intercom numbers, System Speed dial bins, or entries in the
Local Number/Name Translation Table. You may view the
Directory List beginning with any letter of the alphabet, then
scroll through the list either forward or backwards.
Directory Dialing may also be used to transfer a call from one
station to another.
To view the Directory List:
1. Dial the Directory List dial code [680] on the dial pad,
-orPress flexible button programmed as a directory dialing
button,
-orUse the Soft Key’s DIR-DIAL option when in an idle
condition.
2. Press a button on the keypad that represents the letter of
the alphabet, to begin viewing the list of names.
For example … pressing 2 once will produce names
starting with A. When 2 is pressed a second time, names
that start with B will display. Pressing 2 a third time will
display names that start with C.
44
Directory Dial
3. The alphabet is represented on the keypad as shown:
A=2
B = 22
C = 222
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
*
OPER
0
#
Names beginning with the letter chosen will show on the
LCD display.
If there are no names in the Directory List
beginning with the desired letter, a name with the
next higher letter displays on the LCD display.
Letters “Q” and “Z” are not marked on many
telephone keypads; however, the illustration
above shows the correct keys used to access these
letters.
4. Dial [.] to scroll up (next entry) through the list,
-orDial [#] to scroll down (previous entry) through the list,
-orPress another key to view the list for a different letter of the
alphabet.
5. When the desired name displays on the LCD, press the
SPEED button to automatically dial the destination station
or outside phone number (via speed dial).
Do Not Disturb
45
To transfer a call using Directory Dialing while on a call:
1. Press the TRANS button.
2. Dial the Directory Dial Code [680] on the dial pad,
-orPress the flexible button programmed for directory dialing.
3. Press the digit associated with the person’s name and when
it displays, press SPEED to automatically dial the
destination station.
4. Hang up to complete the transfer.
Calls may be transferred to internal stations only.
An attempt to transfer a call off-net (via a speed
dial bin) results in the call recalling upon going
on-hook.
SINGLE LINE TELEPHONE
Not applicable
Do Not Disturb
To activate Do Not Disturb:
Press preprogrammed DND button (button lights steady),
-orUse the Soft Key’s DND option when in an idle mode,
-orDial [631] on the 8-button keyset. The DND button can be
pressed while the phone is ringing to stop the ringing.
46
Do Not Disturb
To remove Do Not Disturb:
Press preprogrammed DND button,
-orUse the Soft Key’s DND option,
-orDial either [631] or [662]. The button LED will extinguish
and DND is cancelled.
To activate One-time Do Not Disturb:
Press the preprogrammed DND button while you are off-hook
and connected to a CO line or intercom call. The DND button LED
will light, and off-hook tones at your station are cancelled.
To cancel One-time Do Not Disturb:
Replace the handset. The DND button LED will extinguish
and DND will be cancelled.
SINGLE LINE TELEPHONE
To
1.
2.
3.
activate Do Not Disturb:
Lift the handset.
Dial [631].
Replace the handset.
To
1.
2.
3.
remove Do Not Disturb:
Lift the handset.
Dial [631] or [662].
Replace the handset.
Executive Override
47
Executive Override
Use of this feature when the executive override
warning tone is disabled may be a violation of Federal,
State or Local Laws, and an invasion of privacy. Check
applicable laws in your area before using this feature.
Executive Override allows stations designated as “Executive”
the ability to override and “barge in” on other keysets engaged
in CO Line conversations. A change in volume may occur on the
CO Line or intercom call after the barge-in occurs.
If you call a busy station:
1. Press the preprogrammed EXECUTIVE OVERRIDE button
(625). The Executive station is bridged onto the CO line
conversation in progress at the called station. An optional
warning tone is presented to all parties prior to cut-thru.
2. Replace the Executive station handset to terminate the
override.
Flash
When connected to an outside line:
Press FLASH to disconnect the outside line and reseize an
outside line dial tone.
Flash Key on Intercom
When connected to a page zone or another internal party:
Press FLASH to disconnect page or intercom call. An
intercom dial tone will sound.
48
Flexible Button Programming
Flexible Button Programming
To program a flexible button (to use feature codes):
1. Press SPEED twice.
2. Press the button to be programmed (must be programmed
in database as a flexible button).
3. Dial the desired code. A confirmation tone will sound. (Refer
to the “Default Numbering Plan” on page 96, and the feature’s
description for any additional digits to enter).
4. Press the ON/OFF button.
To program a flexible button (to use speed bin dialing):
1. Press SPEED twice.
2. Press the button to be programmed (must be programmed
in database as a flexible button).
3. Press the SPEED button.
4. Dial the speed bin number. A confirmation tone will sound.
5. Press the ON/OFF button.
To
1.
2.
3.
4.
To
1.
2.
3.
4.
erase a flexible button:
Press SPEED twice.
Press the flexible button to be erased.
Press FLASH. A confirmation tone will sound.
Press the ON/OFF button.
check flexible button programming:
Lift handset.
Press SPEED, then dial [7] + [#].
Dial [2] to select the KEYBTN option.
Press the desired flexible button(s) to display programming
for the button(s) on the LCD.
5. When finished, replace the handset.
Group Listening
49
Group Listening
All digital key stations have a built-in speakerphone. You can
use the speaker to monitor a call while using the handset to
consult with the outside party. This enables other people in the
room to listen to both parties in the conversation.
To activate Group Listening:
While conversing on the handset, press the ON/OFF button.
Both parties of the conversation can then be heard on the
digital station's speaker. The speakerphone microphone is
muted while the handset is off-hook.
To deactivate Group Listening:
While off-hook, press the ON/OFF button.
Group Listening is NOT available when the station
is in the Headset Mode.
Headset Mode
A modular headset may be used by connecting the headset to
the handset jack on the telephone (leaving the handset in
place). The ON/OFF button on the Digital Telephone is used to
initiate and end calls while using the headset.
To activate Headset Mode:
Dial [634] on the dial pad,
-orPress the preprogrammed HEADSET MODE button.
-orUse the Soft Key’s HEADSET option when in an idle
condition.
50
Headset Mode
The LED will light steady.
While Headset mode is active, the ON/OFF button
activates the headset and disables speakerphone and
intercom call announce operation at your station.
To install the headset, see the Installation Manual.
To deactivate Headset Mode:
Dial [634] on the dial pad,
-orPress the preprogrammed HEADSET MODE button.
-orUse the Soft Key’s HEADSET option when in an idle
condition.
The LED will extinguish.
Station must be programmed in database
programming for headset operation before the
flexible button can be programmed.
SINGLE LINE TELEPHONE
Not applicable
Intercom
51
Intercom
Using an Intercom Button
To
1.
2.
3.
program a Flexible Button as an Intercom Button:
Press the SPEED button twice.
Press the desired flexible button to program.
Dial [645] on the dial pad. A confirmation tone will sound. If
an error was made during entry, an error tone will sound.
When intercom call rings a busy station (w/intercom btn):
1. The calling station receives ringback tone instead of busy
tone. The called station hears muted or reminder ring and
their intercom button LED starts flashing at the incoming
CO line rate. This indicates an incoming intercom call.
2. The called station can place the current CO call on hold by
pressing the HOLD button,
-orPlace the current intercom call on hold by pressing the
HOLD button. The intercom call is placed on hold on the
available intercom button.
3. The called station then presses the flashing intercom
button to answer incoming intercom call. When answered,
the following message displays on the called station LCD:
C A LL F R O M S TA X X X
M M M DD Y Y
H H : MM a m
Sta XXX can be a programmed station name.
SINGLE LINE TELEPHONE
Not applicable
52
Intercom
Answering an Intercom Call
Depending on the position of your intercom button signal
switch, answer the intercom call as indicated:
H Mode (No LED) Handsfree Mode -- You will hear three bursts
of tone and an announcement.
Reply handsfree or lift handset for privacy.
P Mode (LED Flashing) Privacy Mode -- You will hear three
bursts of tone and a one-way announcement. The calling party
cannot hear conversations in progress.
Lift handset or press ON/OFF to answer.
-orPosition the H-T-P switch to the H mode to answer.
T Mode (LED On) Tone Mode -- You will hear repeated bursts of
intercom tone ringing and HOLD button slow flashes.
Lift the handset or press the ON/OFF button to answer.
-orPosition the H-T-P switch to the H mode to answer.
Intercom Transfer
To
1.
2.
3.
4.
use Intercom Transfer without DSS Buttons:
Receive or make an intercom call.
Press the TRANS button. An intercom dial tone will sound.
Dial the desired station number.
When the second station answers, you are in a supervised
transfer mode (first station is staged for transfer).
5. Hang up (stations 1 and 2 will be connected).
To
1.
2.
3.
4.
use Intercom Transfer with DSS Buttons:
Receive or make an intercom call using a DSS button.
Press the TRANS button. An intercom dial tone will sound.
Press the DSS button where to transfer the call.
Hang up (stations 1 and 2 will be connected).
Intercom
53
Intercom Calls
To place an Intercom Call:
1. Press the DSS button of the party to be called (if
programmed at your phone),
-orDial the extension number.
Dialing a number in the numbering plan activates
the telephone automatically.
(You will hear ringing if the called station is in the T mode;
or three bursts of tone if called station is in H or P mode.)
2. Lift the handset or use the speakerphone after the tone
bursts stop.
3. Hang up to end the call.
To answer an Intercom Call:
In the T mode (LED On), you will hear repeated bursts of
intercom tone ringing and the HOLD button slow flashes.
Lift the handset or press the ON/OFF button to answer,
-orPosition the H-T-P switch to the H mode to reply.
In the P mode (LED flashes), you will hear three bursts of tone
and one-way announcement. The calling party cannot hear
conversations in progress.
Lift the handset or press the ON/OFF button to answer,
-orPosition the H-T-P switch to the H mode to reply.
In the H mode (No LED), you will hear three bursts of tone and
an announcement.
Reply handsfree or lift the handset for privacy.
54
Keyset Mode
SINGLE LINE TELEPHONE
To place an intercom call:
1. Lift the handset.
2. Dial the intercom number. You will hear ringing if the called
station is in the “T” answering mode or two bursts of tone if
the called station is in the “H” or “P” modes.
3. Hang up to end the call.
To answer an intercom call:
Lift the handset,
-orIf your SLT is equipped with a speakerphone, press the
Speaker button to converse in a handsfree mode.
Keyset Mode
This feature allows you to determine the mode and baud rate
of the optional CTI Module connected to your phone. This
setting is stored in back-up memory in the case of a power
outage or system reset. When telephone is set to AT command
mode, these AT commands are supported.
Mode
Description
Inactive
No CTI information is sent/received by the telephone.
ATD
Modem Dialing Command -- The telephone will recognize the
ATD and accept digits after the command.
ATH or
Modem On-Hook/Off-Hook Command -- ATH or ATH0 will
ATHX
force the telephone to go to the on-hook state from its current
(X= 0 or 1) state. ATH1 will force the telephone to go to the off-hook state
from it’s current state.
CKTU
Command used with Wanderer (a cordless key telephone unit).
The baud rate is not used in this mode; no change is necessary.
PC Phone
CTI information used with Discovery Desktop and Discovery
PCPhone software must be set to 4800 baud rate.
SPI
Service Provider Interface -- Command used with TAPI
applications such as Discovery Link
Last Number Redial
55
At an idle station:
1. Dial the Keyset Mode code [648] on the dial pad,
-orPress the preprogrammed KEYSET MODE button, the
following displays:
I NAC TI V E
2400
M O DE = S AVE = H OL D B AU D= #
.
2. Press [.] to scroll through the keyset modes.
3. Press [#] to scroll through the baud rates.
4. Press the HOLD button to save the desired entries.
SINGLE LINE TELEPHONE
Not applicable
Last Number Redial
The Last Number Redial (LNR) feature permits the automatic
redialing of the last telephone number dialed on an outside
line. Up to 24-digits can be stored. Outside line selection of the
same line used is automatic.
To use Last Number Redial, either:
1. Press the SPEED button.
2. Press [#].
-orUse the Soft Key’s LNR option when in an idle condition.
56
LCR Operation
The system automatically selects the original line used to place
the call and redials the last number dialed.
If that line is busy, the system will select another line
from the same group and redial the number.
If no lines are available in the same group, you will
receive a busy tone and can queue for a line.
If you preselect a line before activating LNR, the
preselection will override the line used originally.
SINGLE LINE TELEPHONE
Not applicable
LCR Operation
To place an outside call when LCR is enabled in the system:
1. Dial [9] on the dial pad or press the preprogrammed LCR
button.
2. Dial the desired telephone number.
3. Wait for an answer. Lift the handset or use the
speakerphone to converse.
If all available lines are busy, remain off-hook for four
seconds to automatically be queued onto LCR for an
available line, then hang up.
To answer an LCR Queue Call Back:
1. When your telephone is signaled, answer the call.
2. The desired telephone number will be automatically
redialed.
Only one LCR Queue Call Back request may be
initiated by a station. When a second request is
made, the first request is cancelled.
If the 911 feature is enabled, the LCR access code
is 800 instead of 9.
Loop Key
57
CO Line Queue Cancel
To cancel a Call Back Request:
1. Dial the CO Line Queue Cancel code [626] on the dial pad.
2. Replace the handset or press the ON/OFF button.
Loop Key
A station not having a direct appearance for a CO line will
receive incoming CO calls and transferred CO calls under the
LOOP button. Only one call at a time can be connected to a
keyset on the LOOP button.
To
1.
2.
3.
4.
make a Loop button:
Press the SPEED button twice.
Press the desired flexible button.
Dial [89].
Press HOLD.
Mailbox Buttons
To
1.
2.
3.
program a station’s mailbox on a flexible button:
Press the SPEED button twice.
Press the desired flexible button to be programmed.
Dial the mailbox feature access code (460-467 = voice mail
group 1-8).
4. Dial the VMID number. A confirmation tone will sound. If an
error is made during entry, an error tone will sound.
Example -- 4606037 represents a voice mail button
(group 1) for VMID 6037 that is in the system with the
centralized voice mail installed.
58
Message Wait
To use a mailbox button:
The called station presses the MAILBOX flexible button and
goes on-hook. The internal or external call is then
transferred to the VM port by the telephone system.
Message Wait
OR
Stations that are busy, unattended, or in DND can be left a
message indication by other stations in the system. Up to five
messages can be left at one keyset. Upon return to the station,
the user can press the flashing MSG WAIT button to ring each
party in sequential order.
To leave a message waiting indication:
If you dial a station that is busy, unattended, or in DND, you can
leave a message waiting indication.
1. Lift the handset or press the ON/OFF button.
2. Dial the desired intercom station.
3. Press the MSG button or use the Soft Key’s MSG option. A
confirmation tone will sound. The called party's MSG
button will flash slowly.
4. Replace the handset or press ON/OFF to end the call.
Up to five messages can be left at any Station.
To answer a message waiting indication:
If your MSG button is lit, you have a message waiting for you.
The first message left is the first one called.
1. Press the MSG button or use the Soft Key’s MSG option. The
station that left message will be signaled with tone ringing.
2. If the called station does not answer, press the MSG button
once to leave message.
Modem
59
SINGLE LINE TELEPHONE
To
1.
2.
3.
leave a message waiting indication:
Lift the handset.
Dial the desired intercom station.
If you do not receive an answer, or a DND tone sounds,
briefly depress and release the hookswitch.
4. Dial [623].
5. Hang up.
To answer a message waiting indication (your message
waiting lamp is flashing or there is an interrupted dial tone
when you lift the handset):
1. Lift the handset.
2. Dial [663]. The station that left message will ring.
Modem
Voice Mail Modem Access
You can program Vodavi voice mail systems using the
telephone system modem.
To access the voice mail system, you can either:
Dial [498], ring directly to 498, be transferred to 498.
Telephone System Modem Access
Feature code 499 is used for access to the telephone system
modem. This modem allows remote telephone system
programming via an SLT or externally by having a call
transferred to extension 499. COs and DIDs (if applicable) can
also be programmed to ring directly to extension 499.
60
Mute
Mute
Pressing the MUTE button while in the speakerphone mode or
using the handset disables the microphone but does not affect
the speech coming over the speaker or handset. Pressing the
illuminated MUTE button again reactivates the microphone.
To disable the microphone:
1. Press MUTE while off-hook on speakerphone or handset to
activate.
2. Press MUTE again to deactivate. Mute automatically
deactivates upon call termination.
Name In Display
Every extension (Key or SLT) has the capability to program your
name so that people using display telephones will see your
name instead of your station number.
To create your name:
1. Dial [690] on the dial pad.
2. Use dial pad keys to enter your name (up to 7 characters).
1
A - 21
B - 22
C - 23
D - 31
E - 32
F - 33
G - 41
H - 42
I - 43
J - 51
K - 52
L - 53
M - 61
N - 62
O - 63
P - 71
R - 72
S - 73
Q - 74
T - 81
U - 82
V - 83
W - 91
X - 92
Y - 93
Z - 94
Other Codes
1 = 1#
8 = 8#
“ = 01
* = *#
2 = 2#
9 = 9#
, = 02
( = #1
3 = 3#
0 = 0#
? = 03
) = #2
4 = 4#
Space = 11
/ = 04
+ = #3
5 = 5#
: = 12
! = *1
= = #4
6 = 6#
- = 13
$ = *2
# = ##
7 = 7#
‘ = 14
& = *4
. = 24
0PER
*
0
#
3. Press the SPEED button to complete programming process.
Night Service
61
To erase your name:
1. Dial [690] on the dial pad.
2. Press the SPEED button to complete the erasing process.
SINGLE LINE TELEPHONE
To create your name:
1. Dial [690] on the dial pad.
2. Enter the name (up to 7 characters may be entered) by
using keys on the dial pad.
3. Briefly depress the hookswitch and release to complete the
programming process.
To erase your name:
1. Dial [690] on the dial pad.
2. Briefly depress the hookswitch and release to erase.
Night Service
To enter Night Service Mode, from an idle station:
Press the preprogrammed NIGHT SERVICE flexible button
[604]. The system is now in the Night Service Mode.
To remove Night Service Mode:
Press the preprogrammed NIGHT SERVICE flexible button
[604] again. The system is now removed from the Night
Service Mode.
62
Off-Hook Voice Over (OHVO)
Off-Hook Voice Over (OHVO)
OR
While off-hook on a call (CO or Intercom), this feature allows
you to receive a voice announcement through the handset
receiver without interrupting the existing call. You may then
respond to the calling party using CAMP ON procedures to talk
to the calling party or use Silent Text Messaging to respond to
the calling party via LCD Displays.
The calling station is placed in a one-time DND mode upon
initiating the voice-over. One-Time DND cannot be toggled
during the OHVO call. The station receiving the OHVO call must
be off-hook and in the “H” mode.
To place an Off-hook Voice Over call:
When an OHVO station calls a busy OHVO station and a busy
tone is received, the calling OHVO station must:
Press a preprogrammed OHVO button [628] or use the Soft
Key’s OHVO option to initiate an OHVO announcement, and
the following occurs:
The HOLD button LED flashes at the called OHVO
station.
The OHVO receiving station receives a one-beep
warning tone. The station receiving the OHVO call must
be off-hook and in H or P mode, then the calling OHVO
party may begin the voice announcement to the called
OHVO party. The called OHVO station’s existing
conversation is uninterrupted and the voice over
announcement does not drown out the existing
conversation. If the receiving station is call forwarded,
use [5#] to override forwarding.
Off-Hook Voice Over (OHVO)
63
The calling OHVO station is not connected or able to
hear the called station’s conversation (connection only
allows calling station to transmit to the called station).
The calling station is placed in a one-time DND
mode upon initiating the Voice Over. One-Time
DND cannot be toggled during the OHVO call.
The station receiving the OHVO call must be
off-hook and in H mode.
To respond to an Off-hook Voice Over:
After receiving an OHVO announcement, three options are
available to respond to the caller:
Option 1 -- This method lets the receiving station respond to
an OHVO announcement utilizing the MUTE feature button.
This button is pressed to carry on a two-way conversation with
the OHVO initiator while still listening to the original call.
Option 2 -- The OHVO receiving station may respond to the
calling station by using the Silent Text Messaging (this feature
is only available to digital key telephones, and the calling
station must be a digital display telephone). The OHVO
receiving station may press a preprogrammed Message button
to respond to the voice over announcement without being
released from the current call (e.g., by pressing a flexible button
preprogrammed for the message IN MEETING, the calling
station receives this message on the LCD display).
Option 3 -- The OHVO receiving station may respond to the
calling OHVO station by using the Camp On feature. The OHVO
receiving station presses the flashing HOLD button to consult
with the calling station. The existing call (CO line) goes on
Exclusive Hold automatically. This method then follows Camp
On procedures and operation.
SINGLE LINE TELEPHONE
Not applicable
64
Outside Calls
Outside Calls
Placing an Outside Line on Hold
If Exclusive Hold Preference is programmed, press HOLD
once for Exclusive Hold or twice for System Hold.
-orIf System Hold Preference is programmed, press HOLD
once for System Hold or twice for Exclusive Hold.
Answering a Recall
When an outside line has remained on hold for an extended
period of time, you are reminded with a recalling ring. (If
Preferred Line Answer is enabled, skip step 1.)
1. Press the OUTSIDE LINE, LOOP, or POOL button (flashes at a
very fast rate).
2. Lift the handset or press ON/OFF to converse with party.
Answering an Outside Call
1. Lift the handset or press the ON/OFF button.
2. Press slow flashing OUTSIDE LINE button or LOOP button.
(If Preferred Line Answer is programmed, you may answer
an outside line by lifting the handset or pressing ON/OFF.)
Placing an Outside Call
To access an outside line for dialing out:
1. Press idle CO line button, POOL button,
-orDial access code: 9, 801-823, 88+LLL. (LLL = CO Line Number)
2. Dial number for outside call.
3. Lift handset or use speakerphone to converse with party.
Paging
65
Paging
If you are given the ability to make page announcements:
1. Lift the handset or press the ON/OFF button.
2. Dial a three-digit paging code,
-or3. Press the preprogrammed PAGING flexible button.
-orUse the Soft Key’s ALLPG IN or ALLPG EX options (versus
codes 709 or 761) when in an idle condition.
Code
Zone
Code
Zone
700
Int/Ext All Call
706
Internal Zone 6
701
Internal Zone 1
707
Internal Zone 7
702
Internal Zone 2
708
Internal Zone 8
703
Internal Zone 3
709
Internal All Call
704
Internal Zone 4
761
External Page Zone
705
Internal Zone 5
4. Speak in a normal tone of voice to deliver message.
Stations receiving a page Announcement can press the
Volume Bar to change Paging Volume. The display shows:
S PEA K E R PAG E [#########]
M M M DD Y Y
H H : M M am
5. Replace the handset to terminate the page announcement.
Stations off-hook or in DND will not hear the
page announcement.
66
Personalized Messages
Paging - Meet Me
To
1.
2.
3.
request another party meet you on a page:
Dial the desired three-digit paging code.
Request the party to meet you on the page.
Do not hang up; wait for the requested party to answer.
To answer a Meet Me Page:
1. Go to the nearest phone.
2. Dial [770] or press the preprogrammed MEET ME flexible
button. You will be connected to party that paged you.
Personalized Messages
Pre-assigned Messages
Each station can select a pre-assigned message to display on
the LCD of any key telephone calling that station. There are ten
messages available.
This feature is unavailable at Attendant stations.
Stations cannot be call forwarded or in DND and have
this feature active.
To select a pre-assigned message:
1. Dial [633] on the dial pad,
-orPress the a preprogrammed PERSONAL MESSAGES button.
2. Dial the 2-digit code for the message that displays. A
confirmation tone will sound; DND button LED will flash.
00 = (clears msgs)
04 = Return Tomorrow
08 = At Home
01 = On Vacation
05 = Return Next Week
09 = On Break
02 = Return AM
06 = On Trip
10 = At Lunch
03 = Return PM
07 = In Meeting
Personalized Messages
67
To cancel a pre-assigned message:
1. Either dial the Personal Messages code [633] + [00], dial
[662], or press the DND button.
2. Replace the handset. The DND button LED will extinguish.
Custom Messages
Each station can select from ten possible custom messages to
display on the LCD of a key telephone calling that station.
These messages are programmed from the first attendant
station for system-wide use.
Each station can also program three unique custom messages.
The Custom Messages feature is not available for use
by attendant stations.
To select a custom message:
1. Dial [633] on the dial pad,
-orPress a preprogrammed PERSONAL MESSAGES button.
2. Dial a valid message number (21-30) for the desired custom
message.
The first Attendant should provide a list of messages to
each station user.
To program a unique custom message:
1. Dial [633] on the dial pad.
2. Dial a valid message number (18-20) for the desired custom
message.
3. Enter a custom message, up to eight characters.
4. Press the HOLD button to save the message.
68
Personalized Messages
To use a unique custom message:
1. Dial [633] on the dial pad.
-orPress a preprogrammed PERSONAL MESSAGES button.
2. Dial a valid message number (18-20) for the desired custom
message.
To cancel a custom message:
1. Either dial the Personal Messages code [633] + [00], dial
[662], or press the DND button.
2. Replace handset. DND button LED extinguishes.
SINGLE LINE TELEPHONE
SLT users can use custom messages (21-30) as described
above. Unique custom messages (18-20) are not applicable.
SLT users cancel the use of a custom message by using
feature code 662.
Date and Time Entry Messages
Station users can activate certain messages that let users enter
a specific time or return date. These messages appear on the
calling station’s display to alert them of the desired party’s
return time or date.
To activate a message with a custom return time or date:
1. Dial the Message Access code [633] on the dial pad.
2. Then dial the desired message number [11- 17].
Users may activate the following messages and be
prompted to enter a return time or date:
[11] = Vacation Until: MM/DD
[15] = At Home Until: HH:MM xm
[12] = Return: HH:MM xm or MM/DD [16] = On Break Until: HH:MM xm
[13] = On Trip Until: MM/DD
[17] = At Lunch Until: HH:MM xm
[14] = Meeting Until: HH:MM xm
Personalized Messages
69
3. Enter the date/time on the dial pad as shown:
Other Codes
1
A - 21
B - 22
C - 23
D - 31
E - 32
F - 33
G - 41
H - 42
I - 43
J - 51
K - 52
L - 53
M - 61
N - 62
O - 63
PRSQ-
T - 81
U - 82
V - 83
W - 91
X - 92
Y - 93
Z - 94
71
72
73
74
0PER
*
0
1 = 1#
8 = 8#
“ = 01
* = *#
2 = 2#
9 = 9#
, = 02
( = #1
3 = 3#
0 = 0#
? = 03
) = #2
4 = 4#
Space = 11
/ = 04
+ = #3
5 = 5#
: = 12
! = *1
= = #4
6 = 6#
- = 13
$ = *2
# = ##
7 = 7#
‘ = 14
& = *4
. = 24
#
4. Press the HOLD button to enter message. A confirmation
tone will sound and the DND button LED will flash.
To cancel the message:
1. Either dial the Personal Messages code [633] + [00], dial
[662], or press the DND button.
2. Replace the handset. The DND button LED will extinguish.
SINGLE LINE TELEPHONE
Not applicable
70
Personalized Messages
Scrollable Canned Messages
The Scrollable Canned Message feature allows you to use a
single digit [#] or [.] to scroll through the canned messages
and select one. When the desired message is displayed,
pressing the hold button places that message on the station
LCD. This feature operates when the phone is in the idle mode
only. This feature cannot be activated if the station is in the Call
Forward or DND mode(s). This feature is not available to
Attendant stations.
To select a Scrollable Canned Message:
1. Dial [633]+[#] on the dial pad,
-orUse the Soft Key’s PERS-MSG option.
-orPress the PERSONAL MESSAGES button. Clear Messages is
always first. The following message displays:
C LE A R ME S S AG E S
N E X T = # PR E V= * S AV E = H O LD
2. Press [#] to scroll through the messages or press [ .] to
scroll backward through the list.
3. Scroll forward through the messages in the following order.
The scroll is a rolodex-type scroll.
1
2
3
4
5
6
-
(Clear Messages)
At Home
At Lunch
In Meeting
On Break
On Trip
7
8
9
10
11
-
On Vacation
Return AM
Return PM
Return Next Week
Return Tomorrow
4. When the desired message displays on the LCD, press the
HOLD button to activate that message on your station. A
confirmation tone will sound; DND button LED will flash.
Personalized Messages
71
To cancel the message:
1. Either dial the Personal Messages code [633] + [00], dial
[662], or press the DND button.
2. Replace the handset. The DND button LED will extinguish.
SINGLE LINE TELEPHONE
Not applicable
Personal Messages Flexible Button
You can program the code [633] onto a flexible button to
speed access to select and use messages.
To
1.
2.
3.
program the Personal Messages Flexible Button:
Press the SPEED button twice.
Press the desired flexible button. The LED will flash.
Dial [633]+[#] on the dial pad. A confirmation tone will
sound.
To use the flexible button, press that flexible button, then
either:
Dial the 2-digit message number (00-10 or 18-30) to
activate the message. Confirmation tone sounds and DND
button LED flashes.
-orPress [#] to scroll forward or [.] to scroll backward through
the list. When desired message is shown on the LCD, press
HOLD to activate that message on your station.
Confirmation tone sounds and DND button LED flashes.
SINGLE LINE TELEPHONE
Not applicable
72
PBX/Centrex Codes on a Flex Button
PBX/Centrex Codes on a Flex Button
For one-button access to Centrex or PBX features:
1. Program Centrex or PBX code into a Station or System
Speed Dial bin, including hook-flash (FLASH key), [.], and
[#] commands (refer to “Speed Dial” on page 80).
2. Program that speed bin onto a flexible button (refer to
“Flexible Button Programming” on page 48).
Release Button
The Release Button feature allows the station user to speed up
call handling time by disconnecting calls while being off-hook.
Using the handset, while off-hook (not the speakerphone):
Press the preprogrammed RELEASE button [641] to
terminate intercom call, transfer sequence, page
announcement or CO call.
Redial
Last Number Redial
To use Last Number Redial, either:
1. Press the SPEED button.
2. Press the pound [#] key. The last number dialed over an
outside line will be automatically redialed.
-orUse the Soft Key’s LNR option when in an idle condition.
Redial
73
Save Number For Redial
If you wish to save the last number you dialed,either:
1. After placing an outside call, keep the handset off-hook.
2. Press the SPEED button twice,
-orUse the Soft Key’s STORE NO option.
Redial a Saved Number
To dial a number that was saved for redial, either:
Press the SPEED button, then press the [.] key.
-orUse the Soft Key’s SNR option when in an idle condition.
The saved number is automatically dialed.
Repeat Redial
When you place a CO call and a Busy or No Answer is
received:
1. Press the preprogrammed RPT REDIAL flexible button [643].
You will receive an LCD prompt for a timer value.
EN TER R P T RE DI A L TI M E R :
XXX
006 -9 99
2. Enter a valid number (006-999 seconds) for the Repeat
Redial Timer. The default value is 060 (one minute). A
confirmation tone will sound when you go on-hook. The
flexible button LED will be lit steady.
When the timer expires, you will receive a signal via a CO
line queue indication on the RPT REDIAL flexible button.
During the Queue Call Back, the LCD display will indicate
that this is a Redial Call Back. Once the line queue is
answered, the LCD will indicate an outgoing CO line.
74
Ring Down / Hot Line / Off-Hook Preference
To activate a redial:
Press the preprogrammed REDIAL flexible button,
-orPress the ON/OFF button,
-orLift the handset, the line will be seized and number is
dialed. If you receive a busy/no answer, you may repeat the
step to activate another redial.
To cancel the operation:
Press the preprogrammed REDIAL flexible button. A
confirmation tone will sound and the Auto Redial function
is cancelled.
SINGLE LINE TELEPHONE
Not applicable
Ring Down / Hot Line / Off-Hook
Preference
If your phone has been programmed for Off-Hook Preference,
you can access an outside line, or a feature by going off-hook or
pressing the ON/OFF button. It simulates the depression of a
specific button and can be programed by a station user or a
database administration programmer using code [691] + the
button number.
Ring Down / Hot Line / Off-Hook Preference
75
While Off-Hook Preference is enabled, you may access
internal intercom dial tone as follows:
1. Press the preprogrammed ICM button,
-orDial your intercom number. (Do not lift the handset or press
the ON/OFF button before dialing intercom number.) The
LED will light steady and an intercom dial tone will sound.
2. Dial an internal station or feature access code.
Off-Hook Preference Programming (Via a Station)
If your phone is programmed for Off-Hook Preference and you
were given the ability to enable or change the prime flexible
button:
1. Dial [691] on the dial pad.
2. Dial desired button number. Refer to the following chart:
F
F
F
F
F
F
01
05
09
13
17
21
F
F
F
F
F
F
02
06
10
14
18
22
F
F
F
F
F
F
03
07
11
15
19
23
F
F
F
F
F
F
04
08
12
16
20
24
To disable Off-Hook Preference:
1. Dial [691] on the dial pad.
2. Dial [00] on the dial pad.
SINGLE LINE TELEPHONES
When establishing an Off-hook Preference for SLT stations, it
is necessary to program the SLTs CO line or line group, to
access when going off-hook.
Single line telephones can bypass Off-hook Preference by
doing a hookflash and then dialing their extension number.
76
Ring Tone
Ring Tone
To select a distinctive ring tone for a station:
1. Dial the Ring Tone program code [695] on the dial pad. The
following message displays:
E N TE R R I NG TO NE S
00-36
X X P R E S S S P E E D T O S AV E
2. Enter a valid tone number. The speaker will sound a steady
tone that correlates to the 2-digit entry. The 2-digit tone
number will display in the lower left corner of the LCD.
The ringing choices are as follows:
CO RING TONE*/FREQUENCY
Tone (#)
Freq
Tone (#)
Freq
Tone (#)
Freq
00
697/770
13
770/1633
26
1209/1336
01
697/852
14
770/0
27
1209/1477
02
697/941
15
852/941
28
1209/1633
03
697/1209
16
852/1209
29
1209/0
04
697/1336
17
852/1336
30
1336/1477
05
697/1477
18
852/1477
31
1336/1633
06
697/1633
19
852/1633
32
1336/0
07
697/0
20
852/0
33
1477/1633
08
770/852
21
941/1209
34
1477/0
09
770/941
22
941/1336
35
1633/0
10
770/1209
23
941/1477
36
OFF
11
770/1336
24
941/1633
12
770/1477
25
941/0
Tone Duration* =
50 ms/50 ms
3. When the desired tone is selected (default ringing code is
set to 00), press the SPEED button to save it as the tone to
present to callers. A confirmation tone will sound.
School Zone
77
School Zone
Description
The School Zone feature allows a person at a station(s)
specified as an Administrator to control incoming calls for all
stations specified as a Classroom. The Administrator controls
the type of call forwarding and the call forwarding destination.
Call forwarding types include All Call Forward, No Answer Call
Forward, Busy Call Forward, and Busy / No Answer Call Forward.
Valid call forwarding destinations include station numbers,
hunt groups, UCD groups, and Voice Mail groups.
Stations to be included as part of the School Zone feature must
be assigned in Admin programming as either an Administrator
station or as a Classroom station. After these assignments have
been established, the Administrator can easily control call
forwarding for the specified Classroom stations by using
feature code 630.
Operation
To control School Zone call forwarding (at an
Administrator station):
1. Dial [630] + a call forward condition code (0 or 6-9) + a valid
destination number
Call Forward Condition Codes:
0 = Disabled
6 = All Call Forward
7 = No Answer Call Forward
8 = Busy Call Forward
9 = Busy / No Answer Call Fwd
Valid Destinations:
Station Numbers
Hunt Groups
UCD Groups
Voice Mail Groups
2. Press [HOLD]. A confirmation tone sounds.
78
School Zone
To view call forwarding status of Classroom telephones:
1. The Administrator uses a station assigned as an
Administrator station and dials feature code [630] + [#]. A
confirmation tone sounds and the LCD updates to show
one of the following displays:
C LA S S R O O M S TATU S
B S Y F W D TO X XX X
CL A S S R O OM S TATU S
B / NA F W D TO X XX X
C LA S S R O O M S TATU S
N A F W D TO X X X X
CL A S S R O OM S TATU S
F W D TO X X X X
2. Press [ON/OFF] to return to an idle status.
Conditions
»
A station can be assigned as an Administrator or as a
Classroom, but not as both.
»
A call from an Administrator station to a Classroom station
overrides any School Zone call forward settings and the call
rings at the Classroom station.
»
School Zone call forwarding overrides station user call
forwarding and DND.
»
If an E-911 button is programmed, both audible and visual
alert indications will be provided, regardless of School Zone
call forward settings.
»
The School Zone call forwarding feature does not apply to a
Classroom station that is in a hunt group or a UCD group.
Software Version
79
Software Version
The current system software version can be viewed. The display
shows the version number and level of software.
To view the Software Version Display:
Dial the S/W Display code [605] on the dial pad. The top line
of the LCD shows the engineering version of the software.
The bottom line of the LCD shows the features that are
enabled for your software, e.g., BASIC.
Speakerphone
1. Press the ON/OFF button to ON (An intercom dial tone will
sound).
2. Press the DSS key of the desired party or press an available
OUTSIDE LINE button and dial the number.
The speakerphone will be activated.
3. Press the ON/OFF button to end the call.
80
Speed Dial
Speed Dial
A keyset user can associate up to 20 frequently dialed numbers
as Station Speed Numbers (9000-9019). Telephone numbers
can be up to 24 digits including pauses, flash commands,
pulse-to-tone switchover, and non-display characters. A pause
is automatically inserted after a flash.
To use speed dial:
1. If an outside line was not specified in programming, one
can be selected now or the system will assign the line.
2. Press the SPEED button and dial speed bin location,
-orPress the preprogrammed the speed bin button,
-orUse the Soft Key’s SPD option and then dial a speed bin
location when in an idle condition.
To store speed dial numbers:
1. Press the SPEED button once.
2. Press an OUTSIDE LINE button or the POOL button.
-orSelect an outside line by pressing the SPEED button again.
3. Dial the speed bin location.
Speed Dial
81
4. Dial the desired telephone number and include these
special codes:
TRANS -- Initiates a Pulse-To-Tone switchover.
HOLD -- Inserts a Pause.
FLASH -- Inserts a Flash into the speed number.
TRANS -- When used as the first entry in the speed bin, this
inserts a non-display character causing numbers stored in
the bin not to appear on the digital telephone’s display
when bin is accessed.
5. Press the SPEED button.
6. Replace the handset to end the speed bin programming.
To program multiple speed numbers:
1. Press the SPEED button twice to conclude programming a
number.
2. Enter the next speed number bin to program.
If the station has no line appearance for the line
programmed into the speed bin, that line comes up under
the LOOP button or POOL button when accessed.
To
1.
2.
3.
erase an existing speed bin:
Press the SPEED button twice.
Dial the speed bin location.
Press the SPEED button again. A confirmation tone will
sound.
To
1.
2.
3.
SINGLE LINE TELEPHONE
use speed dial:
Lift the handset.
Dial [668] on the dial pad.
Dial the desired station or system speed bin number
(9000-9099).
4. Replace the handset to end the call.
82
To
1.
2.
3.
4.
5.
Station/Port Fixed Number
store speed dial numbers:
Lift the handset.
Dial [661] on the dial pad.
Dial desired station speed number (9000-9019).
Dial the telephone number to store.
Briefly press and release the hookswitch. A confirmation
tone will sound.
Line Group 1 is programmed along with SLT speed
numbers, and thus Line Group 1 is used when
activating station speed dial from an SLT.
System Speed Dial Access
Stations can be individually allowed or denied the ability to use
system speed dial (9020-9099) numbers. (System speed numbers
9060-9099 are not monitored by toll restriction.) Stations cannot
be prevented from using station speed dial.
The first programmed attendant must enter the System Speed
numbers (9020-9099). If an attendant was not specified, system
speed numbers are entered at Station 100.
Station/Port Fixed Number
When a station dials the feature code 611 on a display
telephone, it will display the Fixed Station/Port Number for that
telephone. For example, when using flexible numbering some
programming steps require the “FIXED” code. This code allows
you to dial 611 and quickly determine the fixed port.
S TATI ON P O R T:
XXX
SINGLE LINE TELEPHONE
Not applicable
Station Relocate
83
Station Relocate
The Station Relocation Feature allows you to dial a code
followed by the old station number to bring all the station
attributes including extension number, button mapping, speed
dial, and class of service to the new location.
1. A station can be relocated by unplugging it, then plugging
it into a new location.
2. Dial [636] on the dial pad. Then, dial the extension number
of the station being relocated. Once this is done, all station
attributes are copied to the current station.
If a station is assigned to a specific port and that
station user unplugs their station and plugs it in at
another location, the database administration
programming is updated to reflect the new port
change. Station lock will prevent this feature from
working correctly.
SINGLE LINE TELEPHONE
Not applicable
Text Messaging (Silent Response)
The Text Messaging feature allows you to use text messages to
respond to a caller that has either Camped On or has used the
off-hook voice over (OHVO) feature to alert a busy station of a
waiting call or message. The Camped On station may respond
to the caller via the canned, custom, and silent response text
(LCD) messages. Text messages appear on the calling party LCD
display. The calling (originating) station and receiving station
MUST be digital telephones. The receiving station MUST also be
programmed to allow OHVO calls.
84
Text Messaging (Silent Response)
While receiving a Camp On or OHVO call:
The called party may press a preprogrammed Text Message
button with a specific message [633+XX].
For Example … [633] + [38] means a telephone calling the
station receives the message WHO IS IT ?
Code
Text Message
Code
Text Message
31
I Will Take Call
42
Is It Important?
32
Take Message
43
Is It Urgent?
33
Transfer To Secretary
44
Send Call To Voice Mail
34
Put Call On Hold
45
Park Call
35
Call Back
46
Out Of Office
36
One Moment Please
47
Put Call Through
37
I Will Call Back
48
I Am Busy
38
Who Is It?
49
O.K.
39
Is It Long Distance?
50
No
40
Is It Personal?
51
Yes
41
Is It An Emergency?
SINGLE LINE TELEPHONE
Not applicable
Uniform Call Distribution
85
Uniform Call Distribution
The Uniform Call Distribution (UCD) features are described in
the following sections.
UCD Calls In Queue Display
From an idle display key telephone:
1. Dial [567] followed by the UCD group number (55X),
-orPress the preprogrammed flexible button. The ON/OFF
button LED lights steady.
This idle display prompts a Supervisor that a group is
having problems answering their calls.
The display tells the agent and their supervisor how
many calls are in queue.
The agent automatically receives the calls in queue
display whenever there is a call in queue.
2. Replace the handset or press ON/OFF to terminate display.
This feature cannot be used with a call in progress.
The station is considered busy for incoming calls
during this operation.
UCD Available/Unavailable Mode
If you are a UCD Agent, you can place your station in the
Available mode to receive UCD type calls or in the Unavailable
mode to block UCD calls from ringing to your station.
To enter Available Mode:
Dial [566] on the dial pad to start receiving UCD calls,
-orPress the preprogrammed AVAILABLE/UNAVAILABLE button.
86
Uniform Call Distribution
To enter Unavailable Mode:
Dial [566] on the dial pad to block incoming UCD calls,
-orPress the preprogrammed AVAILABLE/UNAVAILABLE button.
UCD Overflow Station Forward
An enhancement allows UCD calls reaching the Overflow
Station to call forward to another station:
1. Lift the handset or press the ON/OFF button.
2. Press the FWD button or dial [640].
3. Dial the desired code:
[6] = All Calls
[8] = Busy
[7] = No Answer
[9] = Busy/No Answer
4. Dial the 3- or 4-digit destination number where calls are to
be forwarded (Station, Voice Mail, UCD groups, Hunt
group). A confirmation tone will sound.
5. Replace the handset or press the ON/OFF button.
To remove call forwarding:
1. Lift the handset or press the ON/OFF button.
2. Press the FWD button. A confirmation tone will sound and
the FWD LED will extinguish.
Universal Day/Night Answer
87
Universal Day/Night Answer
Incoming CO lines can be programmed for Universal Day
Answer (UDA) or Universal Night Answer (UNA). UDA/UNA
assigned CO lines can also signal over the external page port(s).
If External Day programming is enabled and the system is in
the day mode, the assigned external page port(s) present a
ringing signal. UDA/UNA is established on a per CO line basis in
admin programming.
When the system is in Day or Night mode and an outside
line rings at another station, and you wish to answer it:
Dial [#5] or use the Soft Key’s UDA/UNA option. The
connected outside line can be transferred or disconnected.
Each telephone utilizing Universal Day/Night Answer
must have a loop button appearance if the ringing
outside line does not display at their phone.
Voice Mail
Call Forwarding to Voice Mail Groups
Callers may be routed directly to your mailbox by forwarding
your phone to a voice mail group.
1. Lift handset or press ON/OFF.
2. Press FWD or dial [640].
3. Dial the desired code:
[6] = All Calls
[8] = Busy
[7] = No Answer
[9] = Busy/No Answer
4. Dial the 3-digit Voice Mail group pilot number where calls
are to be forwarded (440-447 = voice mail groups 1-8). A
confirmation tone will sound.
5. Replace handset or press ON/OFF.
88
Voice Mail
Retrieving Voice Messages
To enter the Voice Mail system to check for mail:
Either dial Voice Mail group number, press preprogrammed
VM GROUP flexible button, press flashing MESSAGE WAIT
button, or use the Soft Key’s VM1 option (group 440 only).
You will be prompted to enter your mailbox password.
Voice Mail Transfer with ID Digits
While on a call and the caller on the other end wishes to leave a
Voice Message for another VM user:
1. At the initiating station, press the TRANS. button.
2. Dial the Voice Mail Group number or press the
preprogrammed VM GROUP flexible button.
3. Dial the VMID (Mailbox location) of the desired party and
go on-hook.
Voice Mailbox Button
To
1.
2.
3.
program a Mailbox flexible button:
Press the SPEED button twice.
Press the desired flexible button to be programmed.
Dial the Mailbox feature code (460-467 = voice mail
locations 1-8).
4. Dial the VMID number.
SINGLE LINE TELEPHONE
Not applicable
Voice Mail
89
Voice Mail Group Button
To
1.
2.
3.
4.
program a VM GROUP flexible button:
Press the SPEED button twice.
Press the desired flexible button to be programmed.
Dial a 3-digit VM Group number (440-447=VM groups 1-8).
Dial the VMID number.
Voice Mail Group Access
To access a VM Group:
Dial VM Group number (440-447),
-orPress preprogrammed VM Group flexible button,
-orUse the Soft Key’s VM1 option when in an idle condition (to
access group 440 only).
Voice Mail One-Touch Recording
OR
The Voice Mail One-Touch Recording feature allows the station
user, while on an internal/external call, to press a
preprogrammed flexible button or Soft Key and have the
system record the conversation in the station user’s mailbox.
Use of this feature when the One-Touch Recording
Warning Tone is disabled may be interpreted as a
violation of federal, state or local laws, and an
invasion of privacy. Check applicable laws in your
area before recording calls using this feature.
The “MiniVoice” system does not support Voice Mail
One-Touch Recording.
90
To
1.
2.
3.
Voice Mail
make a VM RECORD flexible button:
Press the SPEED button twice.
Press the desired flexible button to be programmed.
Dial feature code [649] + [VVV] (where VVV = 440-447 for
desired VM group.
While on an internal or external call:
1. Press the preprogrammed VM RECORD button or use the
Soft Key’s REC option (for VM Group 440 only). The LED will
flutter red during the setup and the following message will
display:
R E COR D I NG S E T U P
MMM DD YY
0 0 :0 0 a m
2. Once the system makes the connection, your mailbox and
the flexible button LED will light solid green. The LCD will
display the following message:
R E COR D I NG
MMM DD YY
0 0 :0 0 a m
To pause or resume recording after a pause, press the
preprogrammed 655 key.
3. When you finish recording, press the preprogrammed VM
RECORD button or the Soft Key’s STOP option. The LED will
extinguish and the normal LCD call information will display.
SINGLE LINE TELEPHONE
Not applicable
Voice Mail (Flash-Based) Quick Reference
91
Voice Mail (Flash-Based) Quick Reference
------------------------ MAIN MENU -------------------------Review
Messages
1
While
Playing Msgs...
[1] Rewind
[6] Pause
[7] Rewind (5 sec)
[9] Fast Fwd (5 sec)
[#] Skip to next msg
[.] Cancel play
of message
Send a Mailbox
Message Options
ABC
2
[2] Record Msg
[#] End Msg
[1] Review
[2] Re-record
[3] Append
[.] Cancel
[#] Accept Msg
After
Listening...
[1] Replay
[2] Save
[3] Delete
[4] Forward
[5] Reply
[8] More Info
[#] Confirm Delete
DEF
3
1
Confirm
Cancel
#
*
Mailbox Greeting
[1] Review
[2] Record
[3] Delete
[1] Name
[2] MB Greeting
[3] Temp Greeting
[#] End Recording
2
Password
Enter New Password
Outcall (Pager)
Enter Mailbox
Number
[.] Wrong
number entry
[#] Send Msg
3
[1] Activate/
Deactivate
[4] Enter Outcall #
[1] Review
[2] Change
[3] Delete
4
Direct Transfer
[1] Extension
[2] Mailbox
92
Quick Start for First-Time Users
Voice Mail (Flash-Based)
Quick Start for First-Time Users
1. Obtain System Administrator information:
Voice mail system access number
Your mailbox number
Your temporary password
2. Dial voice mail system access number,
-orCall into the auto attendant, then
press # and enter your mailbox number.
3. After prompt, enter temporary password.
4. Press 3 to access Mailbox Options.
5. Press 2
to access Passwords.
6. After prompt, enter new password.
7. Press 1
to access Greeting Options.
8. Press 2
to select the Record option.
9. Press 1
to record your Name.
10. Press 2
press #
to record your Greeting, then
to end recording.
Volume Control
93
Volume Control
The volume control on the Digital Key Telephone controls
ringing, handset, and speakerphone volumes. It also affects the
receive volume of the “Wanderer” cordless unit.
Display Messages -- While using these function/features, Digital
Key Telephones display the following messages:
Using the speakerphone on
an Intercom call …
SP EA K E R CA LL
MMM DD YY
[#########]
H H : M M am
Using the handset on an
Intercom call …
H A ND SE T IC M
MMM DD YY
[#########]
H H : M M am
Using the speakerphone on a
CO call …
SP EA K E R CA LL
MMM DD YY
[#########]
H H : M M am
Using the handset on a CO
call …
H A ND SE T CO
MMM DD YY
[#########]
H H : M M am
Receiving a page
announcement …
S P E A K E R PAG E
MMM DD YY
H H : M M am
Receiving an incoming tone
ringing Intercom or CO call …
SP EA K E R R IN G
MMM DD YY
[#########]
H H :M M am
94
Volume Control
SINGLE LINE TELEPHONE
The volume control on the Single Line Telephone is located
on the right side of the telephone. The slider switch options
are HI for loud volume, LO for low volume, and OFF to turn
the ringer off. Two-line models have a volume switch for each
line. Certain models do not have an OFF option.
Speakerphone models have a sliding volume switch to adjust
speakerphone volume. Slide the switch toward you for lower
volume or away from you for increased speakerphone
volume.
Each model has a volume button that can be pressed to
increase or decrease the handset volume.
The B/Z ringer switch is located on the bottom of the
telephone near the line jacks. This switch should be set to the
Z mode for business/hospitality applications and to the B
mode for residential applications.
The MSG light and the Line In Use (LIU) LEDs will not
operate when set in the B ringer mode.
For single line telephones that are not equipped with a
volume control slider switch or to increase the volume
greater than that allowed by the slider switch, use the
following steps.
While on a CO line call or an intercom call:
1. Briefly depress and release the hookswitch.
2. Dial 638.
3. Dial a valid number (0-9) to select a volume level.
-orUse [F] or [#] to scroll to increase or decrease volume level.
4. Briefly depress and release the hookswitch to return to the
call.
Worksheets
95
Worksheets
Flexible Button Programming Worksheet
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Speed Dial Bin Programming Worksheet
BIN 9000
BIN 9010
BIN 9001
BIN 9011
BIN 9002
BIN 9012
BIN 9003
BIN 9013
BIN 9004
BIN 9014
BIN 9005
BIN 9015
BIN 9006
BIN 9016
BIN 9007
BIN 9017
BIN 9008
BIN 9018
BIN 9009
BIN 9019
96
Default Numbering Plan
Attendant
608/608+FLASH
●
●
Account Code (reqs btn)
627
●
●
Answering Machine Ring
654+[0]
●
●
Answering Machine Speaker
654+[1]
●
●
Attnd
0
●
Attnd Clear Alarm (T-1)
606
●
Attnd CO Line Ext (Off-Net) Fwd
603+[NNN]+[YYYY]
●
Attnd Custom Message
694+[XX]+message
●
Attnd Day/Night/Special (reqs btn)
631 (DND key)
●
Attnd Directory List Programming
693
●
Attnd Disable Outgoing CO Line
602+press CO line btn
●
Attnd Override (reqs btn)
601
●
Attnd Setting Time and Date
692+date & time
●
Attnd Unavailable
607
●
Attnd Voice Mail Alarm Clear
656
●
Background Music
632+[0] or [1] (off/on)
●
●
Call Back
622
●
●
Call Coverage - Non-Ring (reqs btn)
647+[XXX]
●
●
Call Coverage - Ringing (reqs btn)
646+[XXX]
●
●
Call Forward
640+[C]
●
●
●
Call Forward - External (Off-Net)
[640]+[.]+[YYYY]
●
●
●
Call Forward - Follow Me
642+[XXX]+[C]+dest
●
●
●
Call Park (location 1-8)
430-437
●
●
●
Call Park - Personal
438
●
●
●
Function
911 Alert View/Del (reqs btn)
Code
SLT
Digital
Default Numbering Plan
●
●
●
Attendant
SLT
97
Digital
Default Numbering Plan
439+[XXX]
●
●
●
Call Park Pickup - Station
#6+[XXX]
●
●
●
Call Park Pickup - System (location 1-8)
#430-#437
●
●
●
Call Pickup (reqs btn)
#0
●
●
●
Caller ID Display (Answered Calls)
659
●
●
Caller ID Display (Unans Calls)
635
●
●
Caller ID Name/Number (reqs btn)
653
●
●
Calling Forward Override
5#+[XXX]+press[B]
●
●
●
Calling Sta Handsfree Mode Override
7#+[XXX]
●
●
●
Calling Sta Tone Mode Override
6#+[XXX]
●
●
●
Clear Call Fwd, DND, Personal Msg
662
●
●
●
CO Line (Idle) Direct Access
88+[LLL]
●
●
●
CO Line Grp Access Code (grp 1-23)
801-823
●
●
●
CO Line Grp Access Code (all grps)
824
●
●
●
CO Line Queue
621
●
●
●
CO Line Queue Cancel
626
●
●
●
Dial-By-Name
6
.
●
●
Directory Dial
680
●
●
Do Not Disturb
631
●
DTMF Receiver Test
657
●
●
●
Executive Override
625
●
●
●
Flash (Centrex)
660
Headset Mode
634
●
●
Hunt Group (group 1-8)
450-457
●
●
Intercom Button (reqs btn)
645
●
●
Keyset Mode
648+[#,.]
●
●
Last Number Redial
[SPEED]+[#]
●
●
Function
Call Park - Station
Code
●
●
●
Attendant
SLT
Default Numbering Plan
Digital
98
800
●
●
●
LCR (if active) or CO Line Group 1
9
●
●
●
Loop Key (reqs btn)
89
●
●
Message Wait
623
●
●
Modem
499
●
Modem - Voice Mail Access
498
●
Name in Display
690
●
●
Night Service (reqs btn)
604
●
●
Off Hook Voice Over (reqs btn)
628
●
●
Page - All Call
700
●
●
●
Page - Ext Zone
761
●
●
●
Page - Internal Zones 1-8, All
701-709
●
●
●
Page - Meet Me (Answer)
770
●
●
●
Personal Messages
633+[ZZ]
●
Release Button (reqs btn)
641
●
●
Repeat Redial
643
●
●
Ring Down / Hot Line / Off-Hook Pref
691+[BB]
●
●
Ring Tone
695+[RR]
●
●
Save Number Redial
[SPEED]+[.]
●
●
School Zone
630
●
●
SLT Conference Park
664
●
SLT Directed Call Pickup
#1
●
SLT Message Wait Answer
663
●
SLT Speed Dial
668+[YYYY]
●
SLT Speed Programming
661+[YYYY]
●
SLT Volume
638+[V]
●
Software Version
605
Function
LCR (E911 active on CO Line)
Code
●
●
●
●
●
●
[SPEED]+[YYYY]
●
●
Station Numbers (Fixed)
100-149
●
●
Station/Port Fixed Number
611
●
●
Station Relocate
636+[XXX]
●
●
Stop Trace
658
●
●
UCD Avail/Unavail
566
●
●
UCD CIQ Sta Display (any grp)
567+[UUU]
●
●
UCD Group (grp 1-8)
550-557
●
●
Unanswered CO Call Transfer
639
Function
Speed Dial
Code
SLT
Attendant
99
Digital
Default Numbering Plan
●
●
●
●
Universal Day/Night Answer
#5
●
Voice Mail Group (grp 1-8)
440-447
●
●
Voice Mailbox Btn (reqs btn)
460-467+[VMID]
●
●
VM Msg Cancel (VM Port only)
421+[MMMM]
●
VM Msg Set (VM Port only)
420+[MMMM]
●
VM Msg Set w/cnt (VM Port only)
422+[MMMM]
●
VM One Touch Record (reqs btn)
649+[VVV]
●
●
VM Pse/Res Rec (Dig VM) (reqs btn)
655
●
●
TABLE LEGEND
B = Button w/ feature code:
622 = Call Back
620 = Camp On
625 = Exec Override
623 = Message Wait
628 = OHVO
BB = Button Number
C = Call Forward Condition Code
6 = All Calls
7 = No Answer
8 = Busy
9 = Busy / No Answer)
. = Off-Net (for Follow Me only)
LLL = CO Line Number (001-028)
MMMM = 2- to 4-digit Mailbox Number
●
●
●
NNN = CO Line Group Access Code
of group to be forwarded
801- 823 = CO Group 1-23
824 = All CO Groups
RR = Ring Tone Number (00-36)
V = Volume Control Level (0-9)
VVV =Voice MailGroup Number(440-447)
XX = Custom Message Number (21-30)
XXX = Intercom Station Numbers
YYYY = Speed Dial Bin Numbers
(9000-9099)
ZZ = Personalized Messages
» » » » » » » » NOTES » » » » » » »
www.vodavi.com
©2002 Vodavi Technology, Inc.
VODAVI is a registered trademark of Vodavi Technology, Inc.
P/N: 3552-00
Download PDF
Similar pages
BT Products - Electrocomponents
I6725 Quick Start Guide
CAV-72B/CDT-180
SB67108 Spec Sheet
E5939B
Parts Check List
MI6879 Quick Start Guide
81109 Spec Sheet
82109 Spec Sheet
Aastra 9143i