Crux VIMCF-93C VIM Activation for Select Dodge & Jeep Vehicles 2013-Up Owner's Manual
Crux VIMCF-93C is a video in-motion interface designed for Dodge, Jeep, and RAM vehicles from 2013 to 2015. It allows the passenger to access and input navigation addresses while the vehicle is in motion. The device features a simple installation process and includes a T-harness for easy connection. It also has a dip switch that can be set to permanently activate the video in-motion feature. Additionally, the Crux VIMCF-93C is compatible with various U-Connect radio types, including 8.4-inch screens, 5-inch screens with separate knobs, and 4.
advertisement
INTERFACING SOLUTIONS
VIMCF-93C
DODGE
2014 - 2015 Durango
RAM
2013 - 2015 1500
2013 - 2015 2500
2013 - 2015 3500
JEEP
2014 - 2015 Grand Cherokee
IMPORTANT:
Compatible Nav Radio Type:
U-CONNECT 8.4” SCREEN (1-Piece)
VIDEO IN-MOTION FOR DODGE, JEEP & RAM VEHICLES 2013-UP
INSTALLATION OVERVIEW We recommend reading this installation guide first before starting any work. Following these instructions from “Start” to” Finish” will ensure a smooth and hassle free installation. We offer telephone support M-F
9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.
PARTS INCLUDED:
(1) CF-93C Interface
(1) CF-93C T-Harness
(1) Instruction
PRECAUTIONS:
- Remove the negative side of the battery to avoid any short circuits
durring the installation.
- Do not install the interface near any major components or near the
HVAC system. This may cause damage or overheating to the vehicle.
- Do not disconnect the airbag connection behind the radio panel.
PRELIMINARY :
Please read the entire mannual before installing this interface.
VOLUME
TUNE
TO FACTORY
DISPLAY
SAFETY WARNING:
THIS INTERFACE IS DESIGNED TO ACTIVATE
VIDEO IN-MOTION TO ALLOW THE PASSENER
ACCESS TO THE ADDRESS INPUT WHILE THE
VEHICLE IS IN-MOTION. THIS INTERFACE MAY
CAUSE AN ERROR WHEN SERVICED AT THE OEM
DEALER. BE AWARE THAT MOST DEALERS
WILL ATTEMPT TO VOID THE MANUFACTURERS
WARANTY WHEN INSTALLING ANY AFTERMARKET
EQUIPMENT. IMPROPER USE OF THIS INTERFACE
BY THE DRIVER MAY RESULT IN CITATION. DRIVER
MUST KEEP FULL ATTENTION ON THE ROAD AND
RESPOSIBILITY ON THE SAFETY OF HIS
PASSENGERS.
INSTALLING THE INTERFACE:
1. Remove the factory display to gain access to the factory connectors.
2. Remove the 52-Pin connector from behind the display.
2. Make the T-Harness connections behind the factory display.
(if the connectors do not match please contact tech support)
4. Set dip switch “1” to permanently activate the VIM feature.
5. Test the Navigation address input while the car is in-motion to verify
the VIM is active.
TO ENABLE VIDEO
IN-MOTION
ON
1 2 3 4 5 6
1. On = Enable VIM
2. Not Used
3. Not Used
4. Not Used
5. Not Used
6. Not Used
52-PIN
TO FACTORY
DISPLAY
1 2 3 4 5 6
TUNE
SETTING THE DIP SWITCHES
TO ENABLE VIDEO
IN-MOTION
ON
1 2 3 4 5 6
1. On = Enable VIM
2. Not Used
3. Not Used
4. Not Used
5. Not Used
6. Not Used
ON
TO FACTORY
HARNESS
1 2 3 4 5 6
Rev. 012015
TROUBLE SHOOTING
TO FACTORY
HARNESS
INTERFACING SOLUTIONS
VIMCF-93C
DODGE
2014 - 2015 Durango
RAM
2013 - 2015 1500
2013 - 2015 2500
2013 - 2015 3500
JEEP
2014 - 2015 Grand Cherokee
IMPORTANT:
Compatible Nav Radio Type:
U-CONNECT 8.4” SCREEN (1-Piece)
VIDEO IN-MOTION FOR DODGE, JEEP & RAM VEHICLES 2013-UP
COMPATIBLE RADIOS:
8.4” SCREEN
(SEPARATE KNOBS)
One Piece Radio
5” SCREEN
6-BUTTON
(SEPARATE
KNOBS)
4.3” SCREEN
6-BUTTON
(2 KNOBS)
4.3” SCREEN
4-BUTTON
(2 KNOBS)
Rev. 012015
advertisement
Related manuals
advertisement
