XL 575
PR-2590/PR-2590M
This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference.
PR LIGHTING LTD. http://www.pr-lighting.com
INDEX
SAFE USAGE OF THE PROJECTOR
3
INSTALLING THE PROJECTOR
4
FITTING THE LAMP
4
POWER SUPPLY – MAINS
5
CONTROL CONNECTIONS
5
DMX TERMINATOR
6
SETUP OPTIONS-PROJECTOR CONFIGURATION
6
TO SET THE DMX START ADDRESS
6
OPERATION MENU
ERROR MESSAGES
REPLACING GOBOS
DMX PROTOCOL
7
10
10
11
LED INDICATION
MAINTENANCE
16
16
LUBRICATION
16
KEEPING THE PROJECTOR CLEAN
16
TROUBLESHOOTING
TECHNICAL DATA
17
18
ELECTRICAL DIAGRAM
21
COMPONENT ORDER CODES
23
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence arising from them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.
ACCESSORIES
These items are packed together with the projector:
G clamps
XLR cable
Safety cord
Spare gobos
This manual
Ω clamps
2
1
2
4
1
2
Pcs
Pc
Pcs
Pcs
Pc
Pcs
3-pin plug
Options
2/2
SAFE USAGE OF THE PROJECTOR
When unpacking and before disposing of the carton check there is no transportation damage before using the projector.
Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.
The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other liquids.
The projector is not designed or intended to be mounted directly on to inflammable surfaces.
The projector is only intended for installation, operation and maintenance by qualified personnel.
The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure that no ventilation slots are blocked.
Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle and/or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.
It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.
Do not connect this device to any other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.
Keep the lamp clean. Do not touch the lamp glass with bare hand.
The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be attached as shown in “installing the projector” section.
The lamp used in this projector is a discharge lamp. After switching off don’t attempt to restart the projector until lamp has cooled, this will require approx 15 minutes. Switching the lamp on and off at short intervals will reduce the life of both the lamp and the projector. But occasional breaks will prolong the life of the lamp and projector.
Never run the projector without a lamp.
There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the covers removed.
Always disconnect from the mains, when the device is not in use or before cleaning it or before attempting any maintenance work !
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
3/3
CLAMPS
(2PCS)
HANDLES
(2PCS)
INSTALL THE PROJECTOR
SAFETY CORD
(2PCS)
WARNING
To pass 2 SAFETY CORDS through the TRUSS for safety!
TRUSS
339
106
Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the
WARNING
on the underside of the base as shown above) To pass 2 SAFETY CORDS through the TRUSS for
safety!
Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that the structure that you are going to mount the projector is secure and is strong enough to support a weight of
XL 575.
WARNING:
1. Unlock the PAN and TILT before the 1 st
application of projector for safety.
2. The projector MUST be lifted or carried by the HANDLES instead of clamps.
3. For safety the safety cord should afford 10 times of the unit’s weight.
FITTING THE LAMP
LAMP REFLECTER
NUT
Lock the yoke before fitting/replacing the lamp.
Loosen 4 screws and open the back covers, you can see the structure as shown in the figure above.
Loosen 2 nuts at the both ends of lamp and take out the worn-out lamp. Suggest to free one end after another.
Fit new lamp and fasten 2 screws at the both ends of lamp. Note: don’t touch the bulb of the new lamp with bare hand so as not to influence the beam output; the PST (pumping stem tip off) on the bulb facing the rear cover with fans perpendicularly and being not in the beam’s way is a must and aids cooling.
Close the rear cover and fasten 4 screws.
NOTE:
The convex of the nuts should face to the side when fitting the lamp.
WARNING: The MSI series are high-pressure lamps with external igniters ( ). Care should always be taken when handling these lamps. Always read the manufacturers "Instructions for use" enclosed with the lamp.
4/4
POWER SUPPLY-MAINS
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off.
IMPORTANT
It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards.
CONTROL CONNECTION
Connection between controller and projector and between one projector and another must be made with a 2 core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via cannon 3 pin (which are included with the projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of the plug is not connected in any way. The XL 575 accepts digital control signals in protocol DMX512 (1990).
Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown in the figure below.
No.1
No.2
No. n
DMX IN
DMX OUT
DMX IN CONTROLLER
DMX IN DMX OUT DMX IN DMX OUT
TERMINATER
5/5
DMX TERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120
Ω (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. The connections are illustrated below.
2
120
3
1
DMX TERMINATOR
CONNECTION
Connect a 120 (OHM) resistor across pins 2 and 3 in an XLR plug and insert into the DMX out socket on the last unit in the chain.
PIN 2
PIN 3
SETUP OPTIONS-PROJECTOR CONFIGURATION
CODER BUTTON
UP
UP
Projector configuration can be set conveniently via pressbutton switch and LCD display. Turn the projector on and the
LCD display will show DMX address you set and save last time and it can be reset and saved again as you please.
Launch the projector. Press button ENTER more than 5 seconds to unlock panel.
Press button UP or DOWN if you want to browse through the various Setup Options. There are 8 option codes from DMX Address to Lamp Manual Control, and each code has a specific function. If you turn the coder knob clockwise, the function like as button UP . On the contrary, the function like as button DOWN .
Press button ENTER to save your settings or enter the next menu. There is same function if you push the coder knob.
Press button UP or DOWN to shift.
Press button FUNC, it will return to the upper menu one by one. If you stay for minutes defaulted will show display status automatically.
TO SET THE DMX START ADDRESS
Each XL 575 must be given a DMX start address so that the correct projector responds to the correct control signals.
This DMX start address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the controller. The XL 575 has 3 DMX modes. There are stand mode, extended mode and short mode. For example stand mode has 19 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address
020, No. 3 projector’s address 039, No. 4 projector’s address 058, and so on.
Launch the projector. Press button ENTER or coder knob more than 5 seconds to unlock panel.
Press button FUNC to display DMX address;
Press button UP and DOWN, you can set the address;
Press button ENTER to confirm; In the same time. The GREEN LED will flash one time. It means the setting has been enabled.
Press button FUNC, it will return to the upper menu one by one.
6/6
1st LEVEL
PR LIGHTING
XL SERIES
XL 575
PR LIGHTING
DMX Address
PR LIGHTING
Reset
PR LIGHTING
Config Settings
PR LIGHTING
Option Settings
OPERATION MENU
2nd LEVEL
DMX Address=001
PR LIGHTING
DMX Address
（
001-512）
PR LIGHTING
Reset
Are You Sure?
PR LIGHTING
DMX Mode
PR LIGHTING
Lamp Control
PR LIGHTING
Fixture type
(WARNING：Never change the
fixture type or the system will be damaged!)
PR LIGHTING
Colour Positions
PR LIGHTING
F-Gobo Positions
PR LIGHTING
Pan DMX Invert
3rd LEVEL
PR LIGHTING
DMX Mode
Standard 16
PR LIGHTING
DMX Mode
Extended 16
PR LIGHTING
DMX Mode
Short 8
PR LIGHTING
Lamp Control By
Control Channel
PR LIGHTING
Lamp Control By
Power On
PR LIGHTING
Lamp Control By
DMX Present
PR LIGHTING
Fixture type=
XL 1200
PR LIGHTING
Fixture type=
XL 700
PR LIGHTING
Fixture type=
XL 575
PR LIGHTING
Fixture type=
XL 1200 FS
PR LIGHTING
Fixture type=
XL 1200 Wash
PR LIGHTING
Fixture type=
XL 700 Wash
PR LIGHTING
Colour Positions
STEPPED
PR LIGHTING
Colour Positions
LINEAR
PR LIGHTING
F-Gobo Positions
STEPPED
PR LIGHTING
F-Gobo Positions
LINEAR
PR LIGHTING
Pan DMX Invert
OFF
PR LIGHTING
Pan DMX Invert
ON
7/7
4th LEVEL
PR LIGHTING
Display Options
PR LIGHTING
Tilt DMX Invert
PR LIGHTING
Pan Tilt Swap
PR LIGHTING
Dimmer Invert
PR LIGHTING
Iris Invert
PR LIGHTING
Zoom Invert
PR LIGHTING
Defaults
PR LIGHTING
Display Mode
PR LIGHTING
Display Dimming
8/8
PR LIGHTING
Tilt DMX Invert
OFF
PR LIGHTING
Tilt DMX Invert
ON
PR LIGHTING
Pan Tilt Swap
OFF
PR LIGHTING
Pan Tilt Swap
ON
PR LIGHTING
Dimmer Invert
OFF
PR LIGHTING
Dimmer Invert
ON
PR LIGHTING
Iris Invert
OFF
PR LIGHTING
Iris Invert
ON
PR LIGHTING
Zoom Invert
OFF
PR LIGHTING
Zoom Invert
ON
PR LIGHTING
Defaults
OFF
PR LIGHTING
Defaults
Restore Defaults
PR LIGHTING
Display
On Always
PR LIGHTING
Display
Off After Delay
PR LIGHTING
Disp Dim Level
Min
PR LIGHTING
Disp Dim Level
1
PR LIGHTING
Disp Dim Level
2
PR LIGHTING
Disp Dim Level
3
PR LIGHTING
Disp Dim Level
4
PR LIGHTING
Disp Dim Level
5
PR LIGHTING
Disp Dim Level
6
PR LIGHTING
Disp Dim Level
7
PR LIGHTING
Disp Dim Level
8
PR LIGHTING
Information
PR LIGHTING
Test Modes
PR LIGHTING
Lamp Manual
Control
PR LIGHTING
Display Contrast
PR LIGHTING
Display Language
PR LIGHTING
Lamp Hours
PR LIGHTING
Total Hours
PR LIGHTING
Temperature
PR LIGHTING
Software Version
PR LIGHTING
Factory Setup
PR LIGHTING
Self Test
PR LIGHTING
Lamp Status
PR LIGHTING
Turn Lamp On
PR LIGHTING
Turn Lamp Off
PR LIGHTING
Disp Dim Level
9
PR LIGHTING
Disp Dim Level
Full
PR LIGHTING
Display Contrast
XXX(1~36, Default is 16)
PR LIGHTING
Language =
English
PR LIGHTING
Language =
Chinese
PR LIGHTING
Lamp Hours =
XX
PR LIGHTING
Total Hours =
XX
PR LIGHTING
Display Board
PR LIGHTING
Driver Board 1
PR LIGHTING
Driver Board 2
PR LIGHTING
Pan and Tilt
PR LIGHTING
Display Board
PR LIGHTING
Driver Board 1
PR LIGHTING
Driver Board 2
PR LIGHTING
Pan and Tilt
PR LIGHTING
Power Board
PR LIGHTING
Factory Setup
OFF
PR LIGHTING
Factory Setup
ON
PR LIGHTING
Self Test
OFF
PR LIGHTING self test
ON
PR LIGHTING
Status = XXX
Control = X
PR LIGHTING
Reset Lamp Hours
Are You Sure?
PR LIGHTING
Display Board =
XX℃
PR LIGHTING
Driver Board 1 =
XX ℃
PR LIGHTING
Driver Board 2 =
XX ℃
PR LIGHTING
Pan and Tilt =
XX ℃
PR LIGHTING
Display Board =
X.X.X
PR LIGHTING
Driver Board 1 =
X.X.X
PR LIGHTING
Driver Board 2 =
X.X.X
PR LIGHTING
Pan and Tilt =
X.X.X
PR LIGHTING
Power Board =
X.X.X
9/9
ERROR MESSAGES
In the course of launch, XL 575 examines automatically whether there are errors and if there are, it will display information as follows:
Display
Sensor Err S1-M1
Sensor Err S1-M2
Sensor Err S1-M3
Sensor Err S1-M4
Sensor Err S2-M1
Sensor Err S2-M2
Sensor Err S2-M3
Sensor Err S2-M5
Sensor Err S2-M6
Message
Colour wheel 1 (1# drive board motor 1) error
Prism (1# drive board motor 2) error
Prism rotation (1# drive board motor 3) error
Colour wheel 2 (1# drive board motor 4) error
Rotating Gobo wheel 1 (2# drive board motor 1) error
Gobo rotation 1 (2# drive board motor 2) error
Fixed Gobo wheel (2# drive board motor 3) error
Focus (2# drive board motor 5) error
Zoom (2# drive board motor 6) error
REPLACING GOBOS
PRISM/FROST
FIXED GOBO WHEEL
ROTATING GOBO
WHEEL 1
COLOUR WHEEL 1
COLOUR WHEEL 2
Disconnect the fixture from power. Lock Tilt. Carefully lift off the cover by undoing the 6 screws.
For gobos replacement on the fixed gobo: Remove the gobo and insert the new one into the position by hands.
For gobos replacement on the rotating gobo wheel: Remove the gobo holder with gobo from gobo wheel by hands.
Pull out the spring and drop the old gobo out of the holder.
Insert the new gobo into the holder, and then insert the spring with the narrow end against the gobo.
Push the end of the spring in under lip of the holder.
Pick the spring clip up and put the gobo holder back into the position, if necessary, a small screwdriver will be helped.
Note:
If the gobo is a glass one, it should be touched with glabrous, clean and soft tissue or cloth matted between hand and glass instead of with bare hand.
Close the rear cover and fasten 6 screws.
10/10
DMX PROTOCOL
Short mode
Standard mode
Extended mode
FUNCTION DMX DESCRIPTION
000-010 Black
011-025 Open
026-225 Strobe speed from slow to fast
226-255 Open
2 2 2 Dimmer
000-255 Dimming from dark to light (0-100%)
3 3
3
4
Dimmer Fine
Colour Wheel 1
000-255
000-016
Dimmer in 16 Bit precision
White (Note: stop in DMX value 5,6 or 7 for 5s to activate the reset function)
11/11
033-040 Colour 1/colour 2
049-056 Colour 2/colour 3
065-072 Colour 3/colour 4
081-088 Colour 4/colour 5
097-104 Colour 5/colour 6
113-120 Colour 6/colour 7
121-127 white
128-133 Rainbow rotation speed 1 (slowest)
134-139 Rainbow rotation speed 2
140-145 Rainbow rotation speed 3
146-151 Rainbow rotation speed 4
152-157 Rainbow rotation speed 5
158-163 Rainbow rotation speed 6
164-169 Rainbow rotation speed 7
170-175 Rainbow rotation speed 8
176-181 Rainbow rotation speed 9
182-187 Rainbow rotation speed 10
188-195 Stop in current position
196-201
Rainbow reverse rotation speed
1(slowest)
202-207 Rainbow reverse rotation speed 2
208-213 Rainbow reverse rotation speed 3
214-219 Rainbow reverse rotation speed 4
220-225 Rainbow reverse rotation speed 5
226-231 Rainbow reverse rotation speed 6
232-237 Rainbow reverse rotation speed 7
238-243 Rainbow reverse rotation speed 8
244-249 Rainbow reverse rotation speed 9
250-255 Rainbow reverse rotation speed 10
000-016 White
033-040 Colour 1/colour 2
049-056 Colour 2/colour 3
065-072 Colour 3/colour 4
081-088 Colour 4/colour 5
097-104 Colour 5/colour 6
4 4 5 Colour Wheel 2
113-120 Colour 6/colour 7
121-127 white
128-133 Rainbow rotation speed 1 (slowest)
134-139 Rainbow rotation speed 2
140-145 Rainbow rotation speed 3
146-151 Rainbow rotation speed 4
152-157 Rainbow rotation speed 5
158-163 Rainbow rotation speed 6
164-169 Rainbow rotation speed 7
170-175 Rainbow rotation speed 8
176-181 Rainbow rotation speed 9
182-187 Rainbow rotation speed 10
188-195 Stop in current position
196-201
Rainbow reverse rotation speed
1(slowest)
202-207 Rainbow reverse rotation speed 2
208-213 Rainbow reverse rotation speed 3
214-219 Rainbow reverse rotation speed 4
220-225 Rainbow reverse rotation speed 5
226-231 Rainbow reverse rotation speed 6
232-237 Rainbow reverse rotation speed 7
238-243 Rainbow reverse rotation speed 8
244-249 Rainbow reverse rotation speed 9
250-255 Rainbow reverse rotation speed 10
5 5 6 Iris
7 Iris Fine
000-135 Iris from large to small (0-100%)
136-231 Macro
232-255 Minimal
000-255 Iris n 16 Bit precision
12/12
000-016 Clear
017-032 Gobo1
2
3
4
081-096 Gobo
6
113-127 Gobo
128-132
133-135
136-138
139-141
142-144
145-147
148-150
151-153
154-156
157-159
160-162
163-165
166-168
169-171
172-174
175-177
Reverse rotation speed 1 (slowest)
Reverse rotation speed 2
Reverse rotation speed 3
Reverse rotation speed 4
Reverse rotation speed 5
Reverse rotation speed 6
Reverse rotation speed 7(fastest)
Rotation speed 1 (slowest)
Rotation speed 2
Rotation speed 3
Rotation speed 4
Rotation speed 5
Rotation speed 6
Rotation speed 7(fastest)
Gobo 1 shake 1(slowest)
Gobo 1 shake 2
178-180
181-183
184-186
187-189
190-192
193-195
196-198
199-201
202-204
205-207
208-210
211-213
214-216
217-219
220-222
223-225
Gobo 1 shake 3
Gobo 1 shake 4（fastest）
Gobo 2 shake 1(slowest)
Gobo 2 shake 2
Gobo 2 shake 3
Gobo 2 shake 4（fastest）
Gobo 3 shake 1(slowest)
Gobo 3 shake 2
Gobo 3 shake 3
Gobo 3 shake 4（fastest）
Gobo 4 shake 1(slowest)
Gobo 4 shake 2
Gobo 4 shake 3
Gobo 4 shake 4（fastest）
Gobo 5 shake 1(slowest)
Gobo 5 shake 2
226-228
229-231
232-234
235-237
238-240
241-243
244-246
247-249
Gobo 5 shake 3
Gobo 5 shake 4（fastest）
Gobo 6 shake 1(slowest)
Gobo 6 shake 2
Gobo 6 shake 3
Gobo 6 shake 4（fastest）
Gobo 7 shake 1(slowest)
Gobo 7 shake 2
Gobo
Wheel
250-252
253-255
Gobo 7 shake 3
Gobo 7 shake 4（fastest）
000-021 white
022-042 Gobo1
2
065-085 Gobo
4
107-127 Gobo
128-134
135-142
143-149
150-156
Rotation speed 1 (slowest)
Rotation speed 2
Rotation speed 3
Rotation speed 4 (fastest)
13/13
9 10 12
Gobo rotation
Fine
Prism / Frost
157-163
164-170
171-177
178-184
185-191
192-198
199-205
206-212
Reverse rotation speed 1 (slowest)
Reverse rotation speed 2
Reverse rotation speed 3
Reverse rotation speed 4(fastest)
Gobo 1 shake slow
Gobo 1 shake fast
Gobo 2 shake slow
Gobo 2 shake fast
213-219
220-226
227-233
234-240
Gobo 3 shake slow
Gobo 3 shake fast
Gobo 4 shake slow
Gobo 4 shake fast
241-247
248-255
Gobo 5 shake slow
Gobo 5 shake fast
000-120 0~540°index
121-127 Rotation speed 1 (slowest)
128-135
136-143
144-151
152-159
Rotation speed 2
Rotation speed 3
Rotation speed 4
Rotation speed 5
160-167
168-175
Rotation speed 6
Rotation speed 7
176-183 Rotation speed 8 (fastest) rotating
192-199
200-207
208-215
216-223
224-231
232-239
240-247
248-255
Reverse rotation speed 1 (slowest)
Reverse rotation speed 2
Reverse rotation speed 3
Reverse rotation speed 4
Reverse rotation speed 5
Reverse rotation speed 6
Reverse rotation speed 7
Reverse rotation speed 8 (fastest)
000-255 Gobo rotation in 16 Bit precision
000-051 Clear
052-102
CTO
103-153
Frost
154-204 Prism
2
000-120 Prism
121-127
128-135
136-143
Reverse rotation speed 1 (slowest)
Reverse rotation speed 2
Reverse rotation speed 3
144-151
152-159
160-167
168-175
176-183
184-191
192-199
200-207
Reverse rotation speed 4
Reverse rotation speed 5
Reverse rotation speed 6
Reverse rotation speed 7
Reverse rotation speed 8 (fastest)
Stop in current position
Rotation speed 1 (slowest)
Rotation speed 2
208-215
216-223
224-231
232-239
Rotation speed 3
Rotation speed 4
Rotation speed 5
Rotation speed 6
240-247
248-255
Rotation speed 7
Rotation speed 8 (fastest)
021-255 Wheel full into beam gradually
126-141 Stop in current position
142-255 Reverse rotation speed from slow to fast
14/14
13
14
11 12 14 Focus 000-255
12 13
15
16
17
Focus Fine
Zoom
Zoom Fine
000-255
000-255
000-255
Focus in 16 precision
From large to small
Zoom in 16 precision
14
15
16
17
18
19
20
21
Pan
Pan Fine
Tilt
Tilt Fine
000-255 Pan rotation 450°
000-255 Pan rotation in 16 precision
000-255 Tilt rotation 270°
000-255 Tilt rotation in 16 precision
000-255 Pan&Tilt speed from fast to slow
000-048 Reserved
15 19 23 Control
049-080 Reset
081-112 Reserved
113-144 Lamp off ( stop in DMX value for 10 s)
145-168 Reserved
169-200 Lamp power reduced to 50%
201-223 Reserved
224-255 Lamp on (See remark below)
Remark:
If you intend to turn on/off the lamp via the last channel of the controller, don’t attempt to push the channel to value
224-255 immediately after turning it off, or push the slide bar to value 224-255 to wait it cooling. Under these 2 circumstances, the lamp can not be turned on. The right operation is: turn it off---cool down---push the slide bar to turn it on.
15/15
LED INDICATION
Green
On
Off
Flash
DMX signal OK
No DMX signal
DMX signal error
Red On
MAINTENANCE
If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in any way it must be replaced. If the light from the lamp appears dim this would normally indicate that it is reaching the end of its life and it should be changed at once, aged lamps run to the extremity of their life might explode. If the projector does not function, check the fuses on the power socket of the projector, they should only be replaced by fuses of the same specification. Should these be damaged call a qualified technician before replacement. The projector has thermal protection device that will switch off the projector in case of overheating, should either of these operate, check that the fans are not blocked, and if they are dirty clean them before switching on the projector again. Check that the fans are operational, if not call a qualified technician.
Any maintenance work should only be carried out by qualified technicians.
LUBRICATION
To ensure the continuous rotation of the rotating gobos and linear motion of the lens for focusing, it is recommended that the bearings for the rotating gobos and the 2 shafts for the focusing lens holder be lubricated periodically, preferably every two months. Use only high quality, high-temperature resistant grease instead of any type of oil. When lubricating the bearings, a syringe with a fine needle is the easiest way to introduce the grease to the bearings around each gobo.
KEEPING THE PROJECTOR CLEAN
To ensure the reliability of the projector it should be kept clean. It is recommended that the fans should be cleaned every
15 days. The lens and dichroic colour filters should also be regularly cleaned to maintain an optimum light output.
Do
NOT use any type of solvent on dichroic colour filters.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. A soft cloth and typical glass cleaning products should be used in cleaning. It is recommended to clean the external optics at least once every 20 days and clean the internal optics at least once every 30 / 60 days.
Do not use any organic solvent, e.g. alcohol, to clean the reflector mirror, dichroic colour filters or housing of the apparatus.
16/16
TROUBLESHOOTING
PROBLEM ACTION
The projector doesn’t switch on
Check the fuse on the power socket.
Replace the lamp.
The lamp comes on but the projector doesn’t respond to the controller
Make sure that the projector is correctly configurated.
Replace or repair the DMX cable.
The projector only functions intermittently
Defective projection
The project image appears to have a halo
The beam appears dim
Make sure the fan is working and not dirty.
Check the lenses are not broken.
Remove dust or grease from the lenses.
Make sure the lamp is installed correctly.
Carefully clean the optical group lenses and the projector components.
Check the optics is clean.
Replace with a new lamp of the specified type and rating.
17/17
VOLTAGES:
TECHNICAL DATA
POWER CONSUMPTION:
Electronical ballast（PR-2590）:
Magnetic ballast（PR-2590M）:
LAMP:
650W@220V
710W@220V
PHILIPS
Colour Temperature
Socket
Manufacturers Rated Lamp Life
MSI 575 HR
6000°K
SFc10-4，double ended
750 Hours replacement
Or
OSRAM HMI 575 W/GS
Colour Temperature
Socket
Manufacturers Rated Lamp Life
6000°K
SFc10-4，double ended
1000 Hours replacement
COLOURS:
2 wheel each with 6 dichroic colour filters plus white
With variable speed bi-directional rainbow effect
Step/linear colour changing is available
COLOUR TEMPERATURE CORRECTION:
Linearly colour temperature correction
GOBOS:
1 Rotating gobo wheel:
5 interchangeable gobos+ white, glass or metal gobos can be fixed
Indexable, bi-directionally rotatable at variable speeds
1 Fixed gobo wheel :
7 interchangeable gobos+ white bi-directional wheel scrolling at variable speeds
Gobo diameter: Φ36.3mm
Gobo image diameter: Φ31.5mm
PRISM/ FROST:
1x linear lens, 1x3 facet prism, indexable, bi-directionally rotatable at variable speeds
1xfrost, 1xCTO
18/18
FOCUS:
DMX controlled focus
DIMMER:
0-100% linearly adjustable
SHUTTER:
Double shutter blades, 0.3~12 F.P.S
Macros
HEAD MOVEMENT:
Pan 450º, Tilt 270º with auto position correction
BEAM ANGLE:
12°～34°, linearly adjustable
CONTROL:
DMX512, 3 pin interface
15 channels in short mode, 19 channels in stand mode, and 23 channels in extended mode.
Self-test mode
OTHER FUNCTIONS:
Adjustable Pan & Tilt speed
Fixture and lamp usage time display
LCD display with English and Chinese language menu
Energy saving function of the ballast
Built-in analyzer for easy fault finding, error messages
Built-in demo sequences
Setup options by chargeable battery inside without power connection.
Input signal isolating protection
Network interface (Reserved)
HOUSING:
Composite plastic, IP20
WEIGHT:
Electronical ballast（PR-2590）:
Magnetic ballast（PR-2590M）:
29Kg
34Kg
19/19
SIZES:
See at below
448
237
528
708
480
LIGHT OUTPUT:
34° （ lux）
12° （ lux）
16m
8m
0m
8m
16m
20m
12m
4m
4m
12m
20m
DISTANCE (m)
12° DIAMETER (m)
34° DIAMETER (m)
0
0
0
1730
15970
430
3990
190
1770
110
10000
70
640
20
4.28
12.12
25
5.35
15.15
5
1.07
3.03
10
2.14
6.06
15
3.21
9.09
424
20/20
ELECTRICAL DIAGRAM（PR-2590M）
st Balla LOW
H Bal HIG
CT ELE DC-S
C
A
D
B
C
B
A
D
C
B
A
D
D
B
C
A
C
B
A
D
D
B
C
A
D
B
C
A
C
A
B
D
C
A
D
B
C
B
A
D
D
B
C
A
C
A
B
D
C
A
D
B
C
B
A
D
C
B
A
D
D
B
C
A
1 2
2 LED 3 LED
1 LED 4 LED
21/21
J2 TI
C
A
D
B
C
A
D
B
D
B
C
A
D
B
C
A
J1 PAN
C
B
A
D
D
B
C
A
C
A
D
B
C
B
A
D
C
B
A
D
D
B
C
A
C
A
D
B
C
B
A
D
D
B
C
A
C
A
B
D
D
B
C
A
C
A
B
D
C
B
A
D
D
B
C
A
C
A
D
B
C
B
A
D
ER
ER
ER FAN-POW
GND
FAN-POW
GND
FAN-POW
GND
NS2
NS1
X-SE
X-SE
VCC
VCC
DM
DM
GND
GND
ELECTRICAL DIAGRAM（PR-2590）
ER OW FAN-P
GND
ER OW FAN-P
GND
C
A
B
D
C
A
D
B
C
B
A
D
C
B
A
D
C
A
B
D
C
A
D
B
D
B
C
A
C
A
B
D
C
B
A
D
C
B
A
D
D
B
C
A
D
B
C
A
C
A
B
D
C
A
D
B
C
B
A
D
C
B
A
D
1 2
2 LED 3 LED
1 LED 4 LED
22/22
C
A
D
B
C
A
B
D
C
B
A
D
C
B
A
D
D
B
C
A
D
B
C
A
C
B
A
D
C
B
A
D
C
A
B
D
C
A
D
B
D
B
C
A
C
A
B
D
C
A
B
D
C
A
D
B
C
B
A
D
C
B
A
D
C
A
B
D
C
A
D
B
C
A
D
B
C
B
A
D
2
1
SENS
SENS
VCC
VCC
DMX-
DMX-
GND
GND
POWER SUPPLY
BALLAST****
LAMP
TILT DRIVE BELT
PAN DRIVE BELT
FAN IN FRONT SIDE
FAN NEAR THE LAMP
FAN IN BASE****
FAN IN BACK SIDE
FAN NEAR THE CYM
PAN MOTOR
TILT MOTOR
PRISM ROTATION MOTOR
ROTATING GOBO WHEEL MOTOR
PRISM/FROST MOTOR
FOCUS MOTOR
ZOOM MOTOR
COLOUR WHEEL MOTOR1
COLOUR WHEEL MOTOR2
DIMMER MOTOR
GOBO ROTATION MOTOR
FIXED GOBO WHEEL MOTOR
SHUTTER BLADE MOTOR
IRIS MOTOR
PAN/TILT DRIVE PCB
MOTOR DRIVE PCB 1
MOTOR DRIVE PCB 2
DISPLAY PCB
POWER PCB
POWER PCB****
NOTE
:
**** Only apply to Magnetic ballast.
COMPONENT ORDER CODES
192010123 1
040070049
100050062
290151241
290151234
030060001
030060047
030069003
030060036
030060051
030040089
030040131
030040092
030040073
030040132
030040115
030040116
030040088
230020177
230020210
230020211
230020220
230020183
230020185
24V/12V
2
1
1
2
1
1
1
1
2
1
1
1
1
2
2
1
1
1
1
1
1
1
2
2
1
2
1
1
300W/ 95V 3.6A
MSI 575W HR
HTD-750-3M
HTD501-3M
KD1208PTS1-6 DC12V/2.6W
DC12V 0.38A
DC12V /1.9W
DC12V 0.3A
KDE1205PFV1 11MS
23HS2039L 6.35*25
16HY0002-02L 5*24
17HD0013-32L 5*7
17HS5003-03 5*20
17HD0013-31L 5*23
16HY7001-44 5*18
16HY7001-32L 5*15
39BYG501-4A 5*24
23/23
PR LIGHTING LTD.
571 Yingbin Road, Dashi, Panyu, Guangzhou 511430, China
TEL: +86-20-8478 1888
FAX: +86-20-8478 6023
P/N: 321010262
Last Revision: 13:10:2006
24/24
