Commell FS-97A User's Manual
Commell FS-97A is a full-size single board computer that combines high performance and rich features into a compact form factor. Powered by Intel Mobile solutions with 855GME chipset, it supports Intel Pentium M processor with socket479 and up to 2GB of DDR266/333 SDRAM. Onboard Intel Extreme Graphics 2 Technology provides versatile display options, including CRT, LCD, and analog displays. Additionally, FS-97A offers AC97 2-channel audio, USB2.0 interfaces, one Gigabit Ethernet controller, and a Compact Flash Type II socket for embedded operating system support.
advertisement
FS-97A
Full-size Single Board Computer
User’s manual
Edition 1.3
2009/9/15
FS-97A User’s Manual
Copyright
Copyright
©
2003 - 2004. All rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products.
This document contains proprietary information and protected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are property of their respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at http://www.commell.com.tw
.
2
FS-97A User’s Manual Packing List
Packing List:
Please check the package material before you install the system.
Hardware:
FS-97A Single Board Computer x 1
Cable Kit:
Floppy flat cable x 1
40-pin ATA100 IDE flat cable x 2
DB25 & DB9 cable with bracket x 1
(FS-97AVL only)
Dual DB9 cable with bracket x 1
(FS-97AVL2 only)
DB25 cable with bracket x 1
(FS-97AVL2 only)
Dual USB cable with bracket x 2
3
FS-97A User’s Manual
CPU Cooler x 1
Audio cable with bracket x 1
4-pin to 3-pin ATX cable x 1
Other Accessories:
Divers CD (including User’s Manual)
PS/2 Keyboard & Mouse Cable x 1
4
FS-97A User’s Manual Index
Index
Chapter 1 <Introductions> ................................................................................... 7
1.1 < Product Overview>................................................................................ 7
1.2 <Product Specifications>.......................................................................... 8
1.3 <Component Placement> ...................................................................... 10
1.4 <Block Diagram>.................................................................................... 11
Chapter 2 <Hardware Setup>............................................................................. 13
2.1 <Connectors Location> .......................................................................... 13
2.2 <Jumper Reference> ............................................................................. 14
2.3 <Connectors Reference> ....................................................................... 15
2.3.1 <Internal Connectors> ................................................................ 15
2.3.2 <External Connectors>............................................................... 15
2.4 <System Setup>..................................................................................... 16
2.4.1 <CPU Installation>...................................................................... 16
2.4.2 <Memory Module Installation> ................................................... 17
2.4.3 <CPU Cooler Installation> .......................................................... 18
2.4.4 <Complete the system installation> ........................................... 19
2.5 <CMOS Setup> ...................................................................................... 20
2.6 <Watchdog Timer Setting>..................................................................... 21
2.7 <Embedded Solid State Disk> ............................................................... 22
2.8 <Power and Fan Setup> ........................................................................ 23
2.9 <Display Interface> ................................................................................ 24
2.9.1 <Analog VGA interface> ............................................................. 24
2.9.2 <Digital VGA interface> .............................................................. 25
2.10 < Ethernet Network Interface> ............................................................. 29
2.11 <Audio Interface> ................................................................................. 30
2.12 <GPIO interface> ................................................................................. 31
2.13 <Switch and Indicator>......................................................................... 32
5
FS-97A User’s Manual Index
Chapter 3 <Display Mode Setup> ...................................................................... 33
Chapter 4 <BIOS Setup> .................................................................................... 37
Appendix A <I/O ports pin assignment>........................................................... 39
A.1 <IDE Port> ............................................................................................. 39
A.2 <Floppy Port> ........................................................................................ 40
A.3 < Parallel Port> ...................................................................................... 41
A.4 <Serial Port> .......................................................................................... 42
A.4.1 <External DB9 COM> ................................................................ 42
A.4.2 <Internal COM2>........................................................................ 42
A.5 <USB Port>............................................................................................ 43
A.6 <IrDA Port> ............................................................................................ 43
A.7 <VGA Port>............................................................................................ 44
A.8 <LAN Port> ............................................................................................ 45
A.8.1 <Gigabit Ethernet Controller> .................................................... 45
A.8.2 <Ethernet Controller>................................................................. 45
A.9 <AT Keyboard Port> .............................................................................. 46
A.10 <PS/2 Keyboard & Mouse Port>.......................................................... 46
Appendix B <Flash BIOS>.................................................................................. 47
Appendix C <Watchdog Timer Programming Guide>..................................... 49
6
FS-97A User’s Manual Introduction
Chapter 1 <Introductions>
1.1 < Product Overview>
The FS-97A is an all-in-one single board computer with PICMG interface. Based on Intel
Mobile solutions with 855GME chipset, it supports Intel Pentium M processor with socket479, DDR266/333 SDRAM up to 2GB of capacity, Intel Extreme Graphics 2
Technology of onboard VGA display interface, AC97 2 channel audio, USB2.0 interface and one Gigabit Ethernet controller.
To be a powerful multimedia platform, FS-97A is also integrated with 24-bit dual channel
LVDS interface and one Compact Flash Type II socket. For these features FS-97A can be easily used for industrial multimedia platform like POS or KIOSK system.
Powerful Embedded System
FS-97A also supports Intel Pentium M FC-BGA2 for embedded, you can choose it for lower voltage and power consumption, further more, and it can be done for fan free system.
With one compact flash type II socket, you can port embedded operating system like windows CE.net or Linux Embedded for it.
Hi-Speed USB 2.0 Interface
Intel ICH4 built-in Hi-Speed USB 2.0 controller let FS-97A offering up to 480Mbps of
Hi-Speed USB 2.0 interfaces.
Product Overview 7
FS-97A User’s Manual Introductions
1.2 <Product Specifications>
General Specification
Form Factor
CPU
Memory
Chipset
BIOS
Green Function
Watchdog Timer
Real Time Clock
Enhanced IDE
Full-size PICMG CPU card
Intel Pentium M Processor with FC-PGA478/FC-BGA479
FSB: 400MHz
L2 Cache: 512KB/1MB/2MB
Battery Mode is not supported
Intel Speed Step Technology function is not supported
( The Intel® Celeron® M Processor 4xx series have been designed to work with the Mobile Intel® 945 Express Chipset
Family only .)
2GBytes DDR200/266/333 SDRAM on one 184-pin DIMM socket
ECC is supported
Intel 82855GME GMCH and 82801DB ICH4
Phoenix-Award v6.00PG 4Mb PnP flash BIOS
Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant
System reset programmable watchdog timer with 1 ~ 255 sec./min. of timeout value
Intel ICH4 built-in RTC with lithium battery
PCI enhanced IDE interface supports dual channels and up to 4
ATAPI devices at UltraATA/100
Two 40-pin IDE ports
DiskOnModule (DOM) embedded flash disk up to 1GBytes
Multi-I/O Port
Chipset
Serial Port
USB Port
Parallel Port
Floppy Port
IrDA Port
K/B & Mouse
GPIO
Intel 82801DB ICH4 and Winbond W83627HF-AW LPC Super I/O controller
Two internal RS-232 serial port with 16C550 compatible UART and 16 bytes FIFO
Four Hi-Speed USB 2.0 ports with 480 Mbps of transfer rate
One internal bi-direction parallel port with SPP/ECP/EPP mode
One FDD port supports up to two FDD
One IrDA compliant Infrared interface supports SIR
External PS/2 keyboard and mouse ports on rear I/O panel
One internal AT keyboard port
One 12-pin Digital I/O connector with 8-bit programmable I/O interface
VGA Display Interface
8
Chipset
Memory
Display Type
Intel 855GME GMCH built-in Intel Extreme Graphics 2
With 266 MHz VGA core and 256-bit 3D engine
Intel dynamic video memory up to 64Mbytes shared with system
CRT, LCD monitor and analog display
Product Specifications
FS-97A User’s Manual Introduction
Connector External DB15 female connector on rear I/O panel
Internal 40-pin LVDS connector
Ethernet Interface
Chipset
Type
Intel PRO/100+ LAN interface with Intel 82562ET
Optional secondary Gigabit LAN interface with Intel 82540EM
10Base-T / 100Base-TX/1000Base-T for 82540EM
10Base-T / 100Base-TX for 82562ET auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
External RJ45 connector with LED on rear I/O panel Connector
Audio Interface
Chipset
Interface
Connector
Intel ICH4 with Realtek ALC201A AC97 3D audio codec
2 channel 3D audio with Line-in, Line-out and MIC-in
Internal 10-pin header for line-in/-out, MIC-out, 4-pin header for
CD-in
Extended Interface
Type
Bus type
Onboard 144-pin Mini-AGP interface
4x AGP bus
Solid State Disk Interface
Flash Type
Capacity
Compact Flash Type-I/II for CFC (Compact Flash Card) or IBM
MicroDrive
Up to 1GB flash memory
Power and Environment
Power
Requirement
ATX function
Dimension
Temperature
4-pin onboard +5V/+12V power connector
Onboard 3-pin PS-ON & 5V standby connector
338 (L) x 122 (H) mm
Operating within 0 ~ 60 o
C (32 ~ 140 o
F)
Storage within -20 ~ 85 o
C (-4 ~ 185 o
F)
Ordering Code
FS-97AVL
FS-97AVL2
Full-size PICMG single board computer with Intel Socket 479
Pentium-M processor Motherboard with Intel onboard VGA, LAN,
Audio, Hi-Speed USB 2.0, Compact Flash socket and LVDS interface.
Same as above and with secondary Gigabit LAN
For further product information please visit the website at http://www.commell.com.tw
Product Overview 9
FS-97A User’s Manual Introductions
1.3 <Component Placement>
Compact Flash Socket
Super I/O
ICH4
Optional
Intel 82540EM
Gigabit LAN
Intel 82562ET
LAN
ISA Bridge
BIOS
Audio Codec
Mini-AGP
2 x DDR266/333 DIMM up to 2GB
Intel 855GME
10
Intel Pentium M Processor at 400MHz FSB
Component Placement
FS-97A User’s Manual Introduction
1.4 <Block Diagram>
Intel Pentium M processor with FC-PGA2/FC-BGA2
400MHz FSB
CRT
LCD
Mini-AGP
4xAGP
855GME
DDR266/333
2 x 184-pin
DIMM
Up to 2GB
ATAPI Devices
UltraATA100
USB Devices
USB2.0
Audio
AC97 Codec
LPC
ICH4
PHY
PCI Bus
82562ET LAN
Gigabit Ethernet
Controller
ISA Bus
IrDA
PS/2
COM Port
Parallel
Port
Floppy
Block Diagram 11
FS-97A User’s Manual
(This Page is Left for Blank)
12
(This Page is Left for Blank)
FS-97A User’s Manual Hardware Setup
Chapter 2 <Hardware Setup>
2.1 <Connectors Location>
VGA RJ45_1 RJ45_2 PS/2 (COM1 for FS-97AVL)
CN_USB2
CN_COM2
CN_USB1
CN_WOL
SYSFAN
CN_VGA
FDD
CN_LPT
CF
IDE2
IDE1
MINI_AGP
DIMM1
DIMM2
CPU
CN_PS
JFRNT
CN_PWR
CDIN
CN_LVDS
CN_INV
CN_DIO
CPUFAN
CN_ATKB
CN_IR
CN_COM1
CN_AUDIO
Connectors Location 13
FS-97A User’s Manual Hardware Setup
2.2 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting
JCFSEL Compact Flash Addressing Setting
JDOM IDE1 Pin-20 voltage setting
JVLCD
JLAN
LCD Panel Voltage Setting
Ethernet Controller Enable/Disable Setting
JCFSEL
JDOM
JRTC
JVLCD
JLAN
14 Jumper Reference
FS-97A User’s Manual Hardware Setup
2.3 <Connectors Reference>
2.3.1 <Internal Connectors>
Connector Function Remark
CPU mPGA479 CPU socket Standard
DIMM1/2
IDE1
IDE2
FDD
184 -pin DDR SDRAM DIMM socket
40-pin primary IDE connector
44-pin secondary IDE connector
34-pin floppy connector
Standard
Standard
Standard
Standard
CN_VGA 8 x 2-pin VGA connector (pitch = 2.0mm)
CN_USB1/2 5 x 2-pin USB connector (pitch =2.54mm)
CN_COM1/2 5 x 2-pin serial port connector
CN_LVDS 20 x 2-pin LVDS connector
Standard
Standard
Standard
Standard
CN_INV
CN_PS
5-pin panel inverter connector
3-pin ATX function connector
CN_PWR 4-pin power input connector
CN_AUDIO 5 x 2-pin audio connector
CDIN
CN_DIO
CN_WOL
CPUFAN
4-pin CD-ROM audio input connector
6 x 2-pin digital I/O connector
3-pin wake-on-LAN connector
3-pin CPU fan connector
SYSFAN
CN_LPT
CF
3-pin system fan connector
26-pin parallel port connector
Compact Flash Type II socket
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
Standard
2.3.2 <External Connectors>
Connector Function Remark
VGA DB15 VGA connector Standard
RJ45_1
RJ45_2
RJ45 LAN connector
RJ45 LAN connector
Standard
FS-97AVL2
COM1
PS2
Serial port connector
PS/2 Keyboard/Mouse connector
FS-97AVL
Standard
Connectors Reference 15
FS-97A User’s Manual Hardware Setup
2.4 <System Setup>
2.4.1 <CPU Installation>
FS-97A has one 479-pin CPU socket to support Intel Pentium M/Celeron M 478-pin processor. Please follow the instruction to install the processor well.
1. Use flat-type Screw Driver to unlock the CPU locket
CPU Socket
2. Find the pin direction and install the processor on the socket.
3. Lock the socket well.
Unlock
16 CPU installation
FS-97A User’s Manual Hardware Setup
2.4.2 <Memory Module Installation>
FS-97A supports two DDR266/333 SDRAM sockets up to 2GB of capacity. It also supports
ECC (error- correcting code ) function.
DIMM1/2
104-pin 80-pin
Please check the pin number to match the socket side well before installing memory module.
Memory Module Installation 17
FS-97A User’s Manual Hardware Setup
2.4.3 <CPU Cooler Installation>
There is a cooler attached with the board package, please follow the instructions to install the cooler on the processor.
1. Remove the sticker of the base.
2. Put the base through the fixing hole of the processor and paste on the solder side. Then put the cooler through the base pillar.
3. Press the both sides of the cooler shield down and push it to move front
Press here
Move forward
Press here
18 CPU cooler Installation
FS-97A User’s Manual Hardware Setup
2.4.4 <Complete the system installation>
After installing the CPU, CPU cooler and the memory module, please slot the main board into PICMG slot of the backplane carefully. If you connect an ATX power supply with the backplane, you will need to connect an ATX function cable between the main board and the backplane.
PICMG Bus Slot
Notice:
The ATX function connector may have different types on different backplanes, please check the pin assignment for the connector on the backplane before you install the ATX function cable.
To power supply
JFRNT
CN_PS
To power on the system, please check chapter 2.13 to short the power button pin on JFRNT.
Complete the system Installation 19
FS-97A User’s Manual Hardware Setup
2.5 <CMOS Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
Jumper: JRTC
Type: Onboard 3-pin jumper
JRTC Mode
2-3
Default setting
Normal Operation
JRTC
1 3
20 CMOS Setup
FS-97A User’s Manual Hardware Setup
2.6 <Watchdog Timer Setting>
The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program.
Timeout Value Range
- 1 to 255
- Second or Minute
Program Sample
Watchdog timer setup as system reset with 5 second of timeout
2E, 87
2E, 87
2E, 07
2F, 08
2E, 30
2F, 01
2E, F5
2F, 00
Logical Device 8
Activate
Set as Second*
2E, F6
2F, 05
Set as 5
* Minute: bit 3 = 0; Second: bit 3 = 1
You can select Timer setting in the BIOS, after setting the time options, the system will reset according to the period of your selection.
For more specification of watchdog timer program, please check appendix document.
Watchdog Timer Setting 21
FS-97A User’s Manual Hardware Setup
2.7 <Embedded Solid State Disk>
The FS-97A supports the IDE-based, bootable and driver free DiskOnModule (DOM) embedded flash disk. The onboard 40-pin IDE1 and 44-pin IDE2 box header supports normal DOM (DiskOnModule) or M-systems DiskOnChip IDE Pro flash disk with or without the additional VCC power cable.
The FS-97A also supports Compact Flash Card Type I/II interface. The jumper JCFSEL provides you to setup the CF card on master or slave mode.
Jumper: JCFSEL
Type: onboard 3-pin header
JCFSEL Mode
1-2 Master
2-3 Slave
Default setting
Jumper: JDOM
Type: onboard 3-pin header
JDOM Mode
ON
OFF
Default setting
IDE1 pin-20 5V power supply enable
No 5V power supply on IDE1 pin-20
JCFSEL
JDOM CF
1 3
22 Embedded Solid State Disk
FS-97A User’s Manual Hardware Setup
2.8 <Power and Fan Setup>
FS-97A has one 4-pin power input connector expect PICMG bus powering; it also has two fan connectors. For ATX function, you should connect the ATX connector on the backplane with CN_PS on FS-97A.
Connector: CN_PWR
Type: 4-pin P-type connector for +5V/+12V input
Pin Description Pin Description Pin Description Pin Description
1 +12V 2 +5V
Connector: CPUFAN, SYSFAN
Type: 3-pin fan wafer connector
Pin Description Pin Description Pin Description
1 Ground 2 +12V
Connector: CN_PS
Type: 3-pin ATX function connector
Pin Description Pin
1 5V Standby 2
Description
Ground
3
Pin
3
Fan
Description
Power On
CN_PWR
1
4
1 3
CN_PS 1
3
CPUFAN
1 3
CPUFAN
Power and Fan Setup 23
FS-97A User’s Manual Hardware Setup
2.9 <Display Interface>
2.9.1 <Analog VGA interface>
The board is integrated with Intel 855GM GMCH chipset built-in Intel Extreme Graphics
2 with 266 MHz VGA core, 256-bit 3D engine and Intel Dynamic Video Memory up to
64MBytes shared with system memory. The CRT / analog VGA interface includes one external DB15 female connector on bracket and one 8 x 2-pin header connector on board.
(The two interfaces can not be used at the same time)
Connector: CN_VGA
Type: 16-pin (2 x 8) pin header (pitch = 2.0mm)
Pin Description Pin Description
9 Green 1 Red
2 Blue
3 Ground
4 Ground
5 N/C
6 N/C
7 HSYNC
8 Clock
CN_VGA
1
16
VGA
24 Display Interface
FS-97A User’s Manual Hardware Setup
2.9.2 <Digital VGA interface>
The board provides one 20 x 2-pin LVDS interface for LCD panel, it supports 18/24-bit single/dual channel up to 1600 x 1200 of resolution. The jumper JVLCD can let you select your panel whether supports +5V or +3.3V of voltage, and the CN_INV provides panel inverter interface includes backlight controlling and powering.
1
CN_LVDS
40
JVLCD
1 3
1 5
CN_INV
Display Interface 25
FS-97A User’s Manual Hardware Setup
Connector: CN_INV
Type: 5-pin LVDS Power Header
Pin Description
1 +12V
2 GND
3 GND
Connector: JVLCD
Type: 3-pin Power select Header
Pin Description
1 VCC
2 LCDVCC
3 VCC3
4 GND
5 ENABKL
Connector: CN_LVDS
Type: onboard 40-pin connector for LVDS connector
Connector model: HIROSE DF13-40S
Pin Signal Pin Signal
2 LCDVCC 1 LCDVCC
4 GND
6 ATX0-
3 GND
5 BTX0-
8 ATX0+
10 GND
12 ATX1-
14 ATX1+
7 BTX0+
9 GND
11 BTX1-
13 BTX1+
16 GND
18 ATX2-
20 ATX2+
22 GND
15 GND
17 BTX2-
19 BTX2+
21 GND
24 ATXCK- 23 BTX3-
26 ATXCK+ 25 BTX3+
28 GND
30 ATX3-
27 GND
29 BTXCK-
32 ATX3+
34 GND
31 BTXCK+
33 GND
36 PANELCLK 35 N/C
38 PANELDATA 37 N/C
40 N/C 39 N/C
To setup the LCD, you need the components below:
1. A panel (support up to 24-bit dual channel) with LVDS interfaces.
2. An inverter for panel’s backlight power.
3. A LCD cable and an inverter cable.
For the cables, please follow the pin assignment of the connector to make a cable, because every panel has its own pin assignment, so we do not provide a standard cable; please find a local cable manufacture to make cables.
26 Display Interface
FS-97A User’s Manual Hardware Setup
LCD installing guide:
1. Prepare a panel, inverter and FS-97A.
FS-97A SBC
LCD panel Inverter
2. Please check the datasheet of the panel to see the voltage of the panel, and set the jumper JVLCD to +5V or +3.3V.
3. Prepare a LVDS type LCD cable
Panel side
4. Connect all the devices well.
To CN_LVDS
For sample illustrator only
Board side
To CN_INV
Display Interface 27
FS-97A User’s Manual Hardware Setup
After setup the devices well, you need to select the LCD panel type in the BIOS.
The panel type mapping is list below:
BIOS panel type selection form
For 18-bit color
NO. Output format
1
2
640 x 480
800 x 600
3
4
1024 x 768
1280 x 1024
10
11
5 1400 x 1050 Dual Channel @ 108Mhz 13
6 1400 x 1050 Dual Channel @ 122Mhz
7 1600 x 1200 Dual Channel
12 1024 x 768 Dual Channel
For 24-bit color
NO.
Output format
8
9
1024 x 768
1280 x 1024 Dual Channel
1400 x 1050 Dual Channel
1600 x 1200 Dual Channel
1024 x 768 Dual Channel
28 Display Interface
FS-97A User’s Manual Hardware Setup
2.10 < Ethernet Network Interface>
The FS-97A is integrated with one Intel 82562ET PRO/100+ Ethernet interface at the type of 10Base-T/100Base-TX auto-switching Ethernet with full duplex and IEEE 802.3U compliant. The optional secondary Ethernet controller is Intel 82540EM PRO/1000+ at the type of 10Base-T/100Base-TX/1000Base-T auto-switching Ethernet with full duplex and
IEEE 802.3U compliant. The jumper JLAN can let you set to enable/disable onboard primary network function.
Connector: CN_WOL
Type: onboard 3-pin (1 x 3) wafer connector
Pin 1 2 3
Ground +5V Description WOL-Ctrl
Jumper: JLAN
Type: onboard 3-pin header
1-2
2-3
Default setting
Enable Onboard LAN2 controller
Disable Onboard LAN2 controller
CN_WOL
1
3
Intel 82562ET
RJ45_1
RJ45_2
JLAN
1 3
Intel 82540EM
Ethernet Network Interface 29
FS-97A User’s Manual Hardware Setup
2.11 <Audio Interface>
FS-97A provides a stereo audio interface with Realtek ALC201A AC97 Codec. The
CN_AUDIO provides the interface to use attached audio cable, the CDIN can let you connect audio output from CD-ROM drives.
Connector: CN_AUDIO
Type: 10-pin (2 x 5) 2.54-pitch header
Pin Description Pin
1
3
Line – Right
Line – Left
5 MIC
7 N/C
9 Line Out – Right
Connector: CDIN
Type: 4-pin header
Pin Description
Description
2
4
Ground
MIC
6 Ground
8 Line Out – Left
10 Ground
1 CD – Left
2 Ground
3 Ground
4 CD – Right
10
CN AUDIO
1
30
CDIN
Line-in MIC-in Line-out
Audio Interface
FS-97A User’s Manual Hardware Setup
2.12 <GPIO interface>
The board offers 8-bit digital I/O to customize its configuration to your control needs. For example, you may configure the digital I/O to control the opening and closing of the cash drawer or to sense the warning signal from a tripped UPS. The following is a detailed description of how the digital I/O is controlled via software programming.
Connector: CN_DIO
Type: 12-pin (6 x 2) header (pitch = 2.0mm)
Pin Description Pin
1 Ground
3 LGP0
5 LGP1
7 LGP2
9 LGP3
11 VCC
Description
2 Ground
4 LGP4
6 LGP5
8 LGP6
12 +12V
GPIO Interface
1
12
CN_DIO
31
FS-97A User’s Manual Hardware Setup
2.13 <Switch and Indicator>
The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc.
Connector: JFRNT
Type: onboard 14-pin (2 x 7) 2.54-pitch header
Function Signal PIN Signal Function
IDE LED Power
LED
Reset
Power
Button
PWRBT 11
5VSB 13
12
14
N/C
N/C
SPKIN
Speaker
14
JFRNT
1
32 Switch and Indicator
FS-97A User’s Manual Display Mode Setup
Chapter 3 <Display Mode Setup>
This chapter shows you how to setup the display device under Windows OS.
Before you using your display device:
1. Check your software
Before you can use the display device properly, please install the VGA driver.
2. Check your hardware
Please setup the display device properly before you boot up the system.
For configure your Display device, please follow the instructions below:
1. Please lunch Display Properties.
You would see two Graphics Controllers. If you connect two display devices, you would be able to setup each device for color bit and resolution.
This item can let you configure which device would be the primary if you connect two display devices.
This item can let you extend your Windows Desktop to second display device.
If you click the identify button, the screen will pop up the number sequence of your device.
Display Mode Setup 33
FS-97A User’s Manual Display Mode Setup
For advanced display settings, please click Advanced… button and choose Intel(R)
Extreme Graphics.
Please click Graphics Properties button to enter the advanced setup.
34 Display Mode Setup
FS-97A User’s Manual Display Mode Setup
While you entering the Graphics Properties, you will see the options below:
This option can let you configure the CRT monitors for Colors,
Screen Area (Resolution) and
Refresh Rate.
This option can let you configure the LCD panel for Colors, Screen
Area (Resolution) and Full Screen option.
Display Mode Setup 35
FS-97A User’s Manual Display Mode Setup
This option can let you configure the Dual Display for clone mode
(same display on two devices)
This option can let you configure the Dual Display for Extended
Desktop mode
36 Display Mode Setup
FS-97A User’s Manual BIOS Setup
Chapter 4 <BIOS Setup>
The single board computer uses the Award BIOS for the system configuration. The
Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.
The BIOS setup program of the single board computer let the customers modify the basic configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting.
The BIOS section of the manual is subject to change without notice and is provided here for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as that displayed on your screen.
To activate CMOS Setup program, press ＜DEL＞ key immediately after you turn on the system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main
Menu will be displayed as Figure 5-1. You can use arrow keys to select your function, press ＜Enter＞ key to accept the selection and enter the sub-menu.
Figure 5-1 CMOS Setup Utility Main Screen
BIOS Setup 37
FS-97A User’s Manual
(This Page is Left for Blank)
38
(This Page is Left for Blank)
FS-97A User’s Manual I/O ports pin assignment
Appendix A <I/O ports pin assignment>
A.1 <IDE Port>
2
Connector: IDE1/2
Type: 40-pin (20 x 2) box header
Pin Description
1
Pin Description
1 Reset
3 D7
5 D6
7 D5
9 D4
11 D3
13 D2
15 D1
2 Ground
4 D8
6 D9
8 D10
10 D11
12 D12
14 D13
16 D14
17 D0
19 Ground
21 REQ
23 IOW-/STOP
18 D15
20 VCC
22 Ground
24 Ground
25 IOR-/HDMARDY 26 Ground
27 IORDY/DDMARDY 28 IDESEL
29 DACK-
31 IRQ
30 Ground
32 N/C
33 A1
35 A0
37 CS0 (MASTER CS)
34 CBLID
36 A2
38 CS1 (SLAVE CS)
40 Ground
IDE2
IDE1
40
39
IDE Port 39
FS-97A User’s Manual I/O port pin assignment
A.2 <Floppy Port>
Connector: FDD
Type: 34-pin (2 x 17) 2.54-pitch header
Pin Description
1
3
Ground
Ground
5 Ground
7 Ground
9 Ground
11 Ground
13 Ground
15 Ground
17 Ground
19 Ground
21 Ground
23 Ground
25 Ground
27 Ground
29 Ground
31 Ground
33 Ground
2
1
Pin Description
2
4
DRIVE DENSITY SELECT 0
DRIVE DENSITY SELECT 1
6 N/C
8 INDEX-
10 MOTOR ENABLE A-
18 DIRECTION-
20 STEP-
34
33
FDD
40 Floppy Port
FS-97A User’s Manual I/O ports pin assignment
A.3 < Parallel Port>
2
Connector: CN_LPT
Type: 26-pin (2 x 13) 2.54-pitch box header
Pin Description Pin
1
Description
1 STROBE-
2 D0
3 D1
4 D2
5 D3
6 D4
7 D5
8 D6
9 D7
10 ACKNOWLEDGE- 23 Ground
11 BUSY 24 Ground
12 PAPER 25 Ground
13 SELECT+ 26 N/C
26
25
CN_LPT
Parallel Port 41
FS-97A User’s Manual I/O port pin assignment
A.4 <Serial Port>
A.4.1 <External DB9 COM>
Connector: COM1
Type: 9-pin D-sub male connector on bracket
Pin Description Pin
1 DCD
2 SIN
3 SO
4 DTR
5 Ground
Description
6 DSR
7 RTS
8 CTS
9 RI
1
2
3
4
5
6
7
8
9
2 10
A.4.2 <Internal COM2>
Connector: CN_COM2
Type: 10-pin (2 x 5) 2.54-pitch header
Pin Description Pin
1 DCD
3 SO
5 Ground
7 RTS
9 RI
Description
2 SIN
4 DTR
6 DSR
8 CTS
1 9
CN_COM2
42
CN_COM1
COM1
Serial Port
FS-97A User’s Manual I/O ports pin assignment
A.5 <USB Port>
Connector: CN_USB1, CN_USB2
Type: 10-pin (2 x 5) header for dual USB Ports
Pin Description
1 VCC
3 Data0-
5 Data0+
7 Ground
9 Ground
Pin Description
2 VCC
4 Data1-
6 Data1+
8 Ground
2
1
10
9
CN_USB1 CN_USB2
A.6 <IrDA Port>
Connector: CN_IR
Type: 5-pin (1 x 5) 2.54-pitch header for SIR Port
Pin Description
1 VCC
2 N/C
3 IRRXD
4 Ground
5 IRTXD
1
USB Port
CN_IR
43
FS-97A User’s Manual I/O port pin assignment
A.7 <VGA Port>
Connector: VGA
Type: 15-pin D-sub female connector on bracket
3
4
1
2
5
6
11
12
13
14
Pin Description Pin Description Pin Description
1 RED 6 Ground 11 N/C
2 GREEN 7 Ground 12 5VCDA
3 BLUE
4 N/C
5 Ground
8 Ground
10 Ground
13 HSYNC
9 LVGA5V 14 VSYNC
15 5VCLK
VGA
44 VGA Port
FS-97A User’s Manual I/O ports pin assignment
A.8 <LAN Port>
A.8.1 < Fast Ethernet>
1
Connector: RJ45_1
Type: RJ45 connector with LED on bracket
Pin
8
1 2 3 4 5 6 7 8
Description TX+ TXRX+ N/C N/C RXN/C N/C
A.8.2 <Gigabit Ethernet >
1
Connector: RJ45_2 (97AVL2 Only)
Type: RJ45 connector with LED on bracket 10
Pin 1 2 3 4 5
Description TRD0+ TRD0- TRD1+ TRD1NC
Description NC TRD2+ TRD2- TRD3+ TRD3-
RJ45_1
RJ45_2
LAN Port 45
FS-97A User’s Manual I/O port pin assignment
A.9 <AT Keyboard Port>
Connector: CN_ATKB
Type: 5-pin box header
1
5
Pin 1 2 3 4 5
Description VCC Ground N/C DATA CLK
CN_ATKB
A.10 <PS/2 Keyboard & Mouse Port>
Connector: PS2
Type: 6-pin Mini-DIN connector on bracket
Pin
1
3
5
6
2
4
1 2 3 4 5 6
KBD MSD VCC KBC MSC
Note: The PS/2 connector supports standard PS/2 keyboard directly or both PS/2 keyboard and mouse through the PS/2 Y-type cable.
PS2
46 AT Keyboard Port
FS-97A User’s Manual Flash BIOS
Appendix B <Flash BIOS>
B.1 BIOS Auto Flash Tool
The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below: http://www.award.com
http://www.commell.com.tw/support/support.htm
File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the
BIOS flash ship and update the BIOS.
1. Please make a bootable floppy disk.
2. Get the last .bin files you want to update and copy it into the disk.
3. Copy awardflash.exe to the disk.
4. Power on the system and flash the BIOS. (Example: C:/ awardflash XXX.bin)
5. Re-star the system.
Any question about the BIOS re-flash please contact your distributors or visit the web-site at below: http://www.commell.com.tw/support/support.htm
Flash BIOS 47
FS-97A User’s Manual
(This Page is Left for Blank)
48
(This Page is Left for Blank)
FS-97A User’s Manual Watchdog Timer Programming Guide
Appendix C <Watchdog Timer Programming Guide>
WDT source from : WinBond 83627HF
(1) General Description
Winbond has a WDT feature inside its chip. We implement its
function into our circuit .
There are many configuration Registors ( CR ) in 83627HF. The
following sequence must be followed for CR programming :
(*1) Enter the extended function mode
(*2) Configure the configuration registers
(*3) Exit the extended function mode
EFER : Extended Function Enable Registers.( EFER=2Eh in our system )
EFIR : Extended Function Index Register. ( Same addr. with EFER. )
EFDR : Extended Function Data Register.( Located at addr.[ EFIR +1 ] )
For instance ;
(*1) Enter extended function mode
MOV DX,2EH
MOV AL,87H
CLI ; disable interrupt
OUT DX,AL
JMP $+2
OUT DX,AL
STI ; enable interrupt
(*2) Configurate logical device 1 , configuration register CRF0
MOV DX,2EH
MOV AL,07H
OUT DX,AL
; point to Logical Device Number Register
MOV DX,2FH
MOV AL,01H
OUT DX,AL
; select logical device 1
MOV DX,2EH
MOV AL,0F0H
OUT DX,AL
MOV DX,2FH
MOV AL,3CH
OUT DX,AL ; update CRF0 of LD0 with value 3Ch
(*3) Exit extended function mode
MOV DX,2EH
MOV AL,0AAH
OUT DX,AL
The Configuration Register ( CR ) Definition :
Watchdog Timer Programming Guide 49
FS-97A User’s Manual Watchdog Timer Programming Guide
** Chip ( Global ) Control Register ( CCR ) : CR02 -->CR2F.
CR07 = Logical Device Number Register ( LDNR )
** Logical Device 0 ( LD0 ) = FDC , with CR : CR30 -->CRF5 .
When LDNR (= CR07) = 00h , you can program the CR30 --CRF5
related to FDC feature .
** Logical Device 1 ( LD1 ) = Parallel Port,with CR :CR30 -->CRF0.
** LD2 = UART A ( Serial Port 1) ,with CR :CR30 -->CRF0.
** LD3 = UART B ( Serial Port 2) ,with CR :CR30 -->CRF1.
** LD5 = KBC ,with CR :CR30 -->CRF0.
** LD6 = CIR ,with CR :CR30 -->CR70.
** LD7 = GAME PORT,MIDI PORT & GP I/O Port I,with CR :CR30 -->CRF2.
** LD8 = GP I/O Port II,with CR :CR30 -->CRF7.
** LD9 = GP I/O Port III,with CR :CR30 -->CRF3.
** LDA = ACPI,with CR :CR30 -->CRFF.
** LDB = HARDWARE MONITOR, with CR : CR30 --> CRF0
(2) Related CR for WDT programming
CR2B-Bit 4 ; [0] for WDT function ( via Pin89 )
LD8-CRF5-Bit 3; Select WDT count time
0 = second.
1 = minute.
LD8-CRF6 ; WDT time-out period ,
00h = disabled
01h = 1 second/minute .
02h = 2 seconds/minutes .
03h = 3 seconds/minutes .
04h = 4 seconds/minutes .
05h = 5 seconds/minutes .
..........
FEh = 254 seconds/minutes .
FFh = 255 seconds/minutes .
When writing a non-zero value to LD8-CRF6 , this
value will be loaded into WDT counter and start
to count down .Read this register can not get the
WDT time-out period ( the orginal one written into
) , but the current value in WDT counter .
Enable and Refresh WDT : program LD8-CRF6 a
non-zero value .
Disable WDT : program LD8-CRF2 with 00h .
LD8-CRF7- Bit 4 : WDT Status
1 = WDT time-out happened
0 = WDT counting .
50 Watchdog Timer Programming Guide
FS-97A User’s Manual Watchdog Timer Programming Guide
LD8-CRF7- Bit[3..0] : Select IRQ resource for WDT time-out
( Setting of 2 selects SMI )
(3) WDT Programmimg guide
Step 1 . Enter extended function mode as mentioned as above.
Step 2 . Program WDT related CR.
(2-1) CR2B-b[4]P[0] ; Set pin output as WDT function
(2-2) CR07-P08h ; Point to LD8
(2-3) CRF6-Pxyh
; Program WDT time-out period and start
count down . xy = 00 ; No WDT time-out and counting
xy = 01 ; WDT time-out = 30 sec. and starts counting .
............
(2-4) Read CRF7-b4 if needed ; 0 : WDT counting
1 : WDT time-out happened
Step 3. Exit extended function mode as mentioned as above.
Example (ENABLE WDT AND SET WDT time-out = 5 minutes)
Step 1 .
MOV DX,2EH
MOV AL,87H
CLI ; disable interrupt
OUT DX,AL
JMP $+2
OUT DX,AL
STI ; enable interrupt
Step 2 .
MOV DX,2Eh
MOV AL,2BH
OUT DX,AL
MOV DX,2Fh
IN AL,DX ; READ CR2B
AND AL,0EFH
MOV AH,AL
MOV DX,2Eh
MOV AL,2BH
OUT DX,AL
MOV DX,2Fh
MOV AL,AH
OUT DX,AL ; CR2B-b[4]P[0]
MOV DX,2Eh
MOV AL,07H
OUT DX,AL ; point to Logical Device Number Register
Watchdog Timer Programming Guide 51
FS-97A User’s Manual Watchdog Timer Programming Guide
MOV DX,2Fh
MOV AL,08H
OUT DX,AL ; select logical device 8
;
MOV DX,2Eh
MOV AL,0F5H
OUT DX,AL
MOV DX,2Fh
IN AL,DX ;
OR AL,08h ; SELECT MINUTE
MOV AH,AL
MOV DX,2Eh
MOV AL,0F5h
OUT DX,AL
MOV DX,2Fh
MOV AL,AH
OUT DX,AL
MOV DX,2Eh ; SETTING 5 MINUTES
MOV AL,0F6h ; ( LD8-CRF6-P05h )
OUT DX,AL
MOV DX,2Fh
MOV AL,05h
OUT DX,AL
Step 3 . Exit extended function mode
MOV DX,2Eh
MOV AL,0AAH
OUT DX,AL
REMARK :
**** I/O PORT 2Eh --> Index port for programming CR .
2Fh --> Data port for programming CR .
**** LD8-CRF6-P05h :
Program CR index F6h of Logical Device 8
with the value "05h" .
52 Watchdog Timer Programming Guide
FS-97A User’s Manual Contact Information
Contact Information
Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your products, projects and business.
Taiwan Commate Computer Inc.
Address 8F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih
Taipei Hsien, Taiwan
TEL +886-2-26963909
FAX +886-2-26963911
Website
E-Mail http://www.commell.com.tw
(General Information) [email protected]
(Technical Support)
Commell is our trademark of industrial PC division
Contact Information 53
advertisement
Related manuals
advertisement