PLANET WDAP-C7400 Quick guide
Planet WDAP-C7400 is a wireless access point that provides a stable and reliable connection for various devices. With its high speed of 900Mbps, it is perfect for streaming, gaming, and other bandwidth-intensive applications. The device supports both 2.4GHz and 5GHz frequencies, ensuring a wide range of coverage and minimizing interference with other devices.
The WDAP-C7400 is easy to install and configure, making it suitable for both home and office use. It comes with a ceiling plate for convenient mounting, and its compact design allows it to blend seamlessly into any environment.
advertisement
Quick Installation Guide
WDAP-C7400
900Mbps Dual Band Ceiling Mount
Wireless Access Point
1. Package Contents
Thank you for choosing PLANET WDAP-C7400. Before installing the AP, please verify the contents inside the package box.
The WDAP-C7400 should contain the following items in the package:
Wireless AP Ceiling Plate CD-ROM
2. Physical Introduction
Hardware Description
Wi-Fi (2.4G) LED Wi-Fi (5G) LED
RESET
Power LED
PoE LAN
Quick Guide Mounting Kit x 5 x 5
Note
If there is any item missing or damaged, please contact the seller immediately.
– 1 –
3. Hardware Installation
STEP 1: Plug the Ethernet cable into the PoE port.
Reset: Press and hold the reset button for more than 7 seconds to reset to the factory default setting.
– 2 –
STEP 3: Mounting:
(1) Attach the Ceiling Plate to the ceiling.
(2) Mark each point in the Ceiling Plate for the screws.
(3) Remove the Ceiling Plate to drill the points and insert the plastic wall-mounts.
(4) Use screws to lock the Ceiling Plate by a screw driver.
STEP 2: Plug the other end of the Ethernet cable into the PoE switch.
PoE Managed Switch
2
4 6
8
1
5 7
9 10
3
802.3at PoE Switch screw
STEP 4: Attach the WDAP-C7400 to the Ceiling Plate.
Power Requirement: 802.3at 30W power source is required.
– 3 – – 4 –
4. Wired Network Configuration (Windows 7)
A computer with wired Ethernet connection is required for the first-time configuration of the Wireless AP.
1. Click “Start” button located at the lower-left corner of your computer.
2. Click “Control Panel”.
3. Double click “Network and Sharing Center” icon.
4. Click “Change Adapter Settings”.
5. Double click “Local Area Connection”.
6. Select “Internet Protocol Version 4 (TCP/IPv4)” and click “Properties”.
7. Select “Use the following IP address”, and then click
“OK” button twice to save the configuration. For example, as the default IP address of the WDAP-C7400 is
192.168.1.253 and the router is 192.168.1.254, then you may choose from 192.168.1.1 to 192.168.1.252.
5. Entering into the Web Management
Default IP Address: 192.168.1.253
Default Username: admin
Default Password: admin
Default SSID (2.4GHz): Default_2.4G
Default SSID (5GHz): Default_5G
STEP 1: The Web management allows you to access and manage the Wireless AP easily. Launch the Web browser and enter the default IP address
http://192.168.1.253.
STEP 2: When the login window pops up, please enter the
User Name and Password. The default User Name and Password are both “admin”.
Then click OK button to continue.
– 5 –
STEP 3: After you enter into the Web User Interface, go to
WLAN Settings to configure your wireless network.
For security reasons, strongly recommended to configure the Encryption Method and Passphrase of your wireless network.
For security reasons it is recommended to change the password at the first login and memorize it.
– 6 –
STEP 2: Highlight the wireless network (SSID) to connect and click [Connect] button.
STEP 4: Once the basic configuration of the WDAP-C7400 is done, click “Save” button to make the change take effect.
6. Wireless Network Connection
STEP 1: Right-Click on the network icon displayed in the system tray.
– 7 –
STEP 3: Enter the encryption key of the WDAP-C7400 if necessary.
You have already finished the configuration of the
WDAP-C7400. Now you can use your iPhone, iPad, laptop, and any other Wi-Fi device to connect with it wirelessly and start surfing the internet.
Further Information
The above steps introduce simple installations and configurations for the WDAP-C7400. For further configurations of LAN, Wireless,
Access Control, etc, please refer to the user’s manual in the CD.
If you have further questions, please contact the local dealer or distributor where you purchased this product.
2011-E10550-000
– 8 –
Quick Installation Guide
WDAP-C7400
900Mbps Dual Band Ceiling Mount
Wireless Access Point
1. Package Contents
Thank you for choosing PLANET WDAP-C7400. Before installing the AP, please verify the contents inside the package box.
The WDAP-C7400 should contain the following items in the package:
Wireless AP Ceiling Plate CD-ROM
2. Physical Introduction
Hardware Description
Wi-Fi (2.4G) LED Wi-Fi (5G) LED
RESET
Power LED
PoE LAN
Quick Guide Mounting Kit x 5 x 5
Note
If there is any item missing or damaged, please contact the seller immediately.
– 1 –
3. Hardware Installation
STEP 1: Plug the Ethernet cable into the PoE port.
Reset: Press and hold the reset button for more than 7 seconds to reset to the factory default setting.
– 2 –
STEP 3: Mounting:
(1) Attach the Ceiling Plate to the ceiling.
(2) Mark each point in the Ceiling Plate for the screws.
(3) Remove the Ceiling Plate to drill the points and insert the plastic wall-mounts.
(4) Use screws to lock the Ceiling Plate by a screw driver.
STEP 2: Plug the other end of the Ethernet cable into the PoE switch.
PoE Managed Switch
2
4 6
8
1
5 7
9 10
3
802.3at PoE Switch screw
STEP 4: Attach the WDAP-C7400 to the Ceiling Plate.
Power Requirement: 802.3at 30W power source is required.
– 3 – – 4 –
4. Wired Network Configuration (Windows 7)
A computer with wired Ethernet connection is required for the first-time configuration of the Wireless AP.
1. Click “Start” button located at the lower-left corner of your computer.
2. Click “Control Panel”.
3. Double click “Network and Sharing Center” icon.
4. Click “Change Adapter Settings”.
5. Double click “Local Area Connection”.
6. Select “Internet Protocol Version 4 (TCP/IPv4)” and click “Properties”.
7. Select “Use the following IP address”, and then click
“OK” button twice to save the configuration. For example, as the default IP address of the WDAP-C7400 is
192.168.1.253 and the router is 192.168.1.254, then you may choose from 192.168.1.1 to 192.168.1.252.
5. Entering into the Web Management
Default IP Address: 192.168.1.253
Default Username: admin
Default Password: admin
Default SSID (2.4GHz): Default_2.4G
Default SSID (5GHz): Default_5G
STEP 1: The Web management allows you to access and manage the Wireless AP easily. Launch the Web browser and enter the default IP address
http://192.168.1.253.
STEP 2: When the login window pops up, please enter the
User Name and Password. The default User Name and Password are both “admin”.
Then click OK button to continue.
– 5 –
STEP 3: After you enter into the Web User Interface, go to
WLAN Settings to configure your wireless network.
For security reasons, strongly recommended to configure the Encryption Method and Passphrase of your wireless network.
For security reasons it is recommended to change the password at the first login and memorize it.
– 6 –
STEP 2: Highlight the wireless network (SSID) to connect and click [Connect] button.
STEP 4: Once the basic configuration of the WDAP-C7400 is done, click “Save” button to make the change take effect.
6. Wireless Network Connection
STEP 1: Right-Click on the network icon displayed in the system tray.
– 7 –
STEP 3: Enter the encryption key of the WDAP-C7400 if necessary.
You have already finished the configuration of the
WDAP-C7400. Now you can use your iPhone, iPad, laptop, and any other Wi-Fi device to connect with it wirelessly and start surfing the internet.
Further Information
The above steps introduce simple installations and configurations for the WDAP-C7400. For further configurations of LAN, Wireless,
Access Control, etc, please refer to the user’s manual in the CD.
If you have further questions, please contact the local dealer or distributor where you purchased this product.
2011-E10550-000
– 8 –
advertisement
Related manuals
advertisement