Canon | CP510 | User guide | Canon CP510 User guide

User Guide
ENGLISH
Guía del usuario
ESPAÑOL
Guide d'utilisation
FRANÇAIS
CP710
CP510
NOTICE! When a computer is connected to the printer, be sure to install the software and the
printer driver bundled on the supplied CD-ROM (Canon CP Printer Solution Disk).
If you are using another version of software, actual screen contents and procedures may differ
slightly from those indicated in this guide.
¡ATENCIÓN! Cuando se conecte un ordenador a la impresora, asegúrese de instalar el software
y el controlador de la impresora incluidos con el CD-ROM suministrado (disco CP Printer Solution
Disk de Canon).
Si está utilizando otra versión de software, el contenido real de la pantalla y los procedimientos
podrán ser un poco diferentes de los indicados en esta guía.
ATTENTION ! Quand un ordinateur est connecté à l'imprimante, veillez à installer le logiciel et le
pilote d'imprimante inclus sur le CD-ROM fourni (Canon CP Printer Solution Disk).
Si vous utilisez une autre version de logiciel, le contenu réel de l'écran et les procédures peuvent
être légèrement différents de ceux indiqués dans ce guide.
CDI-M193-010
xx05xxxx
© 2005 CANON INC.
PRINTED IN JAPAN
IMPRIMÉ AU JAPON
Contents
Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
About Using the Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
About This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Proper Usage and Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Read This First
Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Separately Sold Products . . . . . . . . . . . . . . . . . . . . . . .
Components Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
This Printer Allows You to Do the Following . . . . . . . .
Printing Procedure and Reference Guides . . . . . . . . .
Let’s Prepare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
19
20
22
24
26
Preparing Your Ink Cassette/
Paper Sets and Paper Cassette . . . . . . . . . . . . . . . . . . . . .
Loading the Ink Cassette . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading the Paper into the Paper Cassette . . . . . . . . . . . .
Loading the Paper Cassette . . . . . . . . . . . . . . . . . . . . . . . .
Placing the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
27
28
29
30
Connecting to a Camera for Printing
Connecting to a Camera for Printing . . . . . . . . . . . . . . 31
Disconnect the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Printing on the separately sold wide size
(100 x 200 mm (4 x 8 in.)) paper . . . . . . . . . . . . . . . . . . . . 32
Printing from Memory Card (CP710 only)
Compatible Memory Cards . . . . . . . . . . . . . . . . . . . . . .
Inserting Memory Cards. . . . . . . . . . . . . . . . . . . . . . . . .
Removing Memory Cards . . . . . . . . . . . . . . . . . . . . . . .
About LCD Monitor and Operation Buttons. . . . . . . . .
33
34
34
35
Main Details Displayed on the LCD Monitor . . . . . . . . . . . . 35
Printing Selected Images (SELECT) . . . . . . . . . . . . . . .
Printing All Images (ALL). . . . . . . . . . . . . . . . . . . . . . . .
Printing by specified camera settings (DPOF). . . . . . .
Specifying the Layout . . . . . . . . . . . . . . . . . . . . . . . . . .
Printing the Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36
37
38
39
40
English
Connecting to a Computer for Printing
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Installing the Software and the Printer Driver . . . . . . . 42
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Connecting the Printer to Your Computer . . . . . . . . . . 48
Software Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Printer Software Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Uninstalling the Software. . . . . . . . . . . . . . . . . . . . . . . . 51
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Uninstalling the Printer Driver. . . . . . . . . . . . . . . . . . . . 52
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Using the Battery Pack (sold separately)
Attaching and Charging the Battery Pack . . . . . . . . . . 55
Battery Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Appendix
Cleaning the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printing with Non-Canon Digital Cameras . . . . . . . . . .
57
58
61
64
66
1
Quick Start
Let’s start by printing on postcard size paper.
This section explains the procedures required to print with the paper and the ink cassette
(trial kit) included with your printer from a camera.
Things to Prepare
Printer (CP710/CP510)
Standard Paper (Postcard size, 5 sheets)
Ink Cassette (Postcard size, for 5 sheets)
Paper Cassette (Postcard size)
Compact Power Adapter CA-CP200
Power Cord
Digital camera or digital camcorder (Prepare a memory card containing the images
you wish to print beforehand)
Camera User Guide or Direct Print User Guide
: Included with the printer
About illustrations used in this guide
This guide uses illustrations mainly for the CP710. Unless otherwise mentioned,
operations are also the same when using the CP510.
1
1
2
Loading the Ink Cassette in the Printer (p. 27)
Open the ink cassette
compartment cover.
2
Load the ink cassette and close
the ink cassette compartment
cover.
2
Loading the paper into the Paper Cassette (p. 28)
1
2
Open the paper cassette’s
top and middle covers.
Place the paper, glossy side up
and the address/stamp side next
to the middle cover, in the paper
cassette.
Paper (Glossy side up)
Top cover
Middle cover
Middle cover
(Address / stamp side
next to the middle cover)
3
3
1
Place the middle cover back to its original position,
and leave the top cover open.
Loading the Paper Cassette into the Printer (p. 29)
Open the paper cassette
compartment cover.
2
Push the paper cassette all the way
into the paper cassette
compartment.
3
Quick Start (Continued)
4
1
Connecting the Printer to a Power Source (p. 30)
Insert the power cord into the
compact power adapter and plug
the other end into a power outlet.
2
Connect the compact power
adapter to the printer’s
DC IN terminal.
1
2
To power outlet
DC IN terminal
5
Connecting the Camera to the Printer (p. 31)
Pull out the retractable USB cable, and connect to the camera’s DIGITAL
terminal.
zIf the connector on the camera side does not match up, use the USB cable included
with your camera.
To DIGITAL terminal
Retractable
USB cable
To USB terminal
4
6
Turning On the Power (p. 31)
Press the printer’s power button until it lights green.
Power button
7
Printing (p. 31)
1
Turn the camera’s power on and display the images.
2
Press the camera’s
zThe
(PictBridge) icon or the
(Canon Direct Print) icon appears on the upper left
corner of the LCD monitor. The icon that is displayed differs according to the camera.
,
, SET or SELECT button.
zThe button to be pressed differs depending on the camera.
zIf the
or
button is pressed, printing starts immediately.
Screen shot of the camera’s LCD monitor
(This differs depending on the camera.)
3
Select [Print] and press the SET or SELECT button.
zPrinting starts. During printing, the printer’s power button blinks green.
With certain camera models, the camera will power up and display its images when it
is connected to the printer with the interface cable. For more details, refer to your
Camera User Guide or Direct Print User Guide included with your camera.
When using non-Canon Digital Cameras, refer to the camera’s user guide for the
camera you are using.
5
Before You Begin
Thank you for your purchase of the Canon Compact Photo Printer SELPHY CP710/
CP510. This guide explains the printer’s general flow of operations, from camera
print settings to printing and computer connection operations to printing.
Before using your printer for the first time, please read through the "Safety Precautions" (p. 11).
„ Warning Against Copyright Infringement
Please respect all copyrights. Use of images produced by SELPHY CP710/CP510
for purposes other than personal entertainment may be prohibited by law.
„ Warranty Limitations
This printer’s warranty is only effective in the country of sale. If a problem arises
while the printer is in use abroad, please convey it back to the country of sale before
proceeding with a warranty claim to a Canon Customer Support center.
For Canon Customer Support contacts, please see the Canon Limited
Warranty supplied with your printer.
6
.
Use of genuine Canon accessories is recommended.
This product is designed to achieve excellent performance when used with genuine Canon
accessories. Canon shall not be liable for any damage to this product and/or accidents such
as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage
and/or explosion of a battery pack). Please note that this warranty does not apply to repairs
arising out of the malfunction of non-genuine Canon accessories, although you may
request such repairs on a chargeable basis.
When used with the EOS 10D, EOS 20D, EOS DIGITAL REBEL, or EOS DIGITAL
REBEL XT
Be sure to set [Communication] in the camera’s menu to [PTP] or [Print/PTP] before
connecting the camera to this printer. If you set [Communication] to [Normal], printing is not
available (refer to the camera’s Instruction Manual for the menu settings).
• The same data transmission settings may be needed when using a non-Canon digital
cameras. For details, read the camera’s user guide.
7
About Using the Software
Read Carefully Before Using!
CANON SOFTWARE LICENSE AGREEMENT
IMPORTANT – READ THIS AGREEMENT BEFORE USING THE SOFTWARE ON THE CD-ROM IN
THIS BOX. BY USING THE SOFTWARE, YOU AGREE TO BE BOUND BY THE TERMS OF THIS
AGREEMENT.
This is a license agreement (the “Agreement”) between you and Canon Inc. (“Canon”).
IF YOU DO NOT AGREE TO THE TERMS AND CONDITIONS OF THIS AGREEMENT, DO NOT USE
THE SOFTWARE PROGRAM ON THE CD-ROM (INCLUDING ALL SOUND AND IMAGE DATA) AND
THE USER MANUAL IN THIS BOX (COLLECTIVELY, THE “SOFTWARE”) AND PROMPTLY RETURN
THE SOFTWARE TO YOUR POINT OF PURCHASE FOR A REFUND.
In consideration of the right to use the SOFTWARE, you agree to abide by the terms and conditions
of this Agreement.
1. LICENSE: Canon grants you the personal, non-exclusive right to use the SOFTWARE only on a single
computer. You may physically transfer the SOFTWARE from one computer to another provided that the
SOFTWARE is used on only one computer at a time. You shall not install or use the SOFTWARE on a
network, multiple CPU, multiple site arrangement, or any other hardware configuration where the
SOFTWARE is accessible to more than one CPU or to more than one user.
With respect to the sound and image data (“Data”) contained in the Software, which are to be
downloaded to the applicable Canon digital camera product, Canon grants you a personal, nonexclusive license to use the Data on a single Canon digital camera product only.
YOU SHALL NOT ASSIGN, SUBLICENSE, RENT, LEASE, LOAN, CONVEY OR OTHERWISE USE,
TRANSFER, COPY, TRANSLATE, CONVERT TO ANOTHER PROGRAMMING LANGUAGE, ALTER,
MODIFY, DECOMPILE OR DISASSEMBLE THE SOFTWARE, IN WHOLE OR IN PART, EXCEPT AS
EXPRESSLY PROVIDED IN THIS AGREEMENT.
2. BACK-UP COPY: You may make one copy of the SOFTWARE solely for back-up purposes, or copy the
SOFTWARE onto the permanent storage device (e.g. a hard disk) of your computer and retain the
original for back-up purposes. Any other copying of the SOFTWARE is a violation of this Agreement.
You must reproduce and include the copyright notice on the back-up copy.
3. SUPPORT AND UPDATES: Neither Canon, nor its subsidiaries, dealers or distributors will be
responsible for providing maintenance or support for use of the SOFTWARE. No updates, fixes or
support will be made available for the SOFTWARE.
4. LIMITED WARRANTY AND LIMITATION OF LIABILITY: It is your responsibility to choose, maintain
and match the hardware and software components of your computer system. Thus Canon does not
guarantee uninterrupted service or correction of errors or that the functions or performance of the
SOFTWARE will meet your requirements. THE SOFTWARE IS LICENSED ON AN “AS IS” BASIS AND
WITHOUT WARRANTY OR CONDITION OF ANY KIND. The CD-ROM storing the SOFTWARE is
warranted only against defective material under normal use for a period of ninety (90) days after
purchase from an authorized Canon dealer as evidenced by your sales receipt. Your sole remedy for a
defective CD-ROM shall be replacement of the same without charge when returned by you at your
expense to your point of purchase and proven to be defective upon inspection. The Replacement CDROM will be warranted for the remainder of the original ninety (90) day warranty period of the defective
CD-ROM. The limited warranty does not apply if the failure of the CD-ROM resulted from accident,
abuse or misapplication of the SOFTWARE and shall not extend to anyone other than the original user
of the SOFTWARE.
EXCEPT AS SPECIFICALLY SET FORTH IN THIS PARAGRAPH 4, CANON, CANON’S
SUBSIDIARIES, DISTRIBUTORS AND DEALERS DISCLAIM ALL WARRANTIES, OR
CONDITIONS, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OR CONDITION OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE
SOFTWARE.
NEITHER CANON NOR ANY OF CANON’S SUBSIDIARIES, DISTRIBUTORS OR DEALERS IS
LIABLE FOR ANY DAMAGES HOWSOEVER CAUSED, INCLUDING WITHOUT LIMITATION,
DIRECT, CONSEQUENTIAL OR INCIDENTAL LOSS OR DAMAGE INCLUDING LOSS OF PROFITS,
EXPENSE OR INCONVENIENCE HOWSOEVER CAUSED OR ARISING OUT OF THE SOFTWARE
OR THE USE THEREOF.
8
NEITHER CANON, NOR ANY OF CANON’S SUBSIDIARIES, DISTRIBUTORS OR DEALERS
SHALL HAVE ANY OBLIGATION TO INDEMNIFY YOU AGAINST ANY CLAIM OR SUIT BROUGHT
BY A THIRD PARTY ALLEGING THAT THE SOFTWARE OR THE USE THEREOF INFRINGES ANY
INTELLECTUAL PROPERTY OF SUCH THIRD PARTY.
SOME STATES, PROVINCES OR LEGAL JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF
IMPLIED WARRANTIES, OR THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES, OR PERSONAL INJURY OR DEATH RESULTING FROM
NEGLIGENCE ON THE PART OF THE SELLER, SO THE ABOVE DISCLAIMERS AND
EXCLUSIONS MAY NOT APPLY TO YOU.
5. TERM: This Agreement is effective upon your using the SOFTWARE and remains in effect until
expiration of all copyright interests in the SOFTWARE unless earlier terminated. You may terminate this
Agreement by destroying the SOFTWARE. This Agreement will also terminate without notice to you if
you fail to comply with any of the terms of this Agreement and you must then promptly return the
SOFTWARE. In addition, Canon may enforce its other legal rights.
6. U.S. GOVERNMENT RESTRICTED RIGHTS NOTICE:
The SOFTWARE is a “commercial item,” as that term is defined at 48 C.F.R. 2.101 (Oct 1995),
consisting of “commercial computer software” and “commercial computer software documentation,” as
such terms are used in 48 C.F.R. 12.212 (Sept 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R.
227.7202-1 through 227.72024 (June 1995), all U.S. Government End Users shall acquire the
SOFTWARE with only those rights set forth herein. Manufacturer is Canon Inc./30-2, Shimomaruko 3chome, Ohta-ku, Tokyo 146-8501, Japan.
7. EXPORT RESTRICTIONS: You agree to comply with all export laws and restrictions and regulations of
the country involved, and not to export or re-export, directly or indirectly, the SOFTWARE in violation of
any such laws and restrictions and regulations, or without all necessary approvals.
8. SEVERABILITY:
In the event that any provision of this Agreement is declared or found to be illegal by any court or
tribunal of competent jurisdiction, such provision shall be null and void with respect to the jurisdiction of
that court or tribunal and all the remaining provisions of this Agreement shall remain in full force and
effect.
9. CONTROLLING LAW: The terms of this Agreement as it relates to purchases of the Software in the
United States of America shall be governed and construed in all respects in accordance with the laws
and regulations of the State of New York, without reference to choice of law principles. The terms of this
Agreement as it relates to purchases of the Software in Canada shall be governed by the laws of the
province of Ontario.
10. OWNERSHIP: All rights, including but not limited to copyrights and trade secret rights, to the
SOFTWARE belong to Canon, its affiliated corporations and third party licensors. Your use of the
SOFTWARE is subject to the laws of the United States, and Canada, and other applicable copyright
and trademark laws, and nothing in this Agreement constitutes a waiver of the rights of Canon, its
affiliated corporations and third party licensors under such laws. You only own the CD-ROM media in
which the Software is stored. Except as expressly provided herein, no license or right, express or
implied, is hereby conveyed or granted by Canon to you for any intellectual property of Canon. Nothing
contained in Paragraph 1 shall be construed to give Canon any ownership rights in any images,
graphics or textual material that you save in connection with the Software.
You may not modify, remove or delete any or all copyright notices (i) which are contained in the
Software, including any copy thereof, and (ii) which are on the original CD-ROM and on the medium of
a back-up copy made pursuant to Section 2 above.
11. ACKNOWLEDGEMENT: BY USING THE SOFTWARE, YOU ACKNOWLEDGE THAT YOU HAVE
READ THIS AGREEMENT, UNDERSTOOD IT, AND AGREE TO BE BOUND BY ITS TERMS AND
CONDITIONS. YOU ALSO AGREE THAT THIS AGREEMENT IS THE COMPLETE AND EXCLUSIVE
STATEMENT OF AGREEMENT BETWEEN YOU AND CANON CONCERNING THE SUBJECT
MATTER HEREOF AND SUPERSEDES ALL PROPOSALS OR PRIOR AGREEMENTS, VERBAL
OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN THE PARTIES RELATING TO
THE SUBJECT MATTER HEREOF. NO AMENDMENT TO THIS AGREEMENT SHALL BE
EFFECTIVE UNLESS SIGNED BY A DULY AUTHORIZED OFFICER OF CANON.
9
About This Guide
„ Symbols Used
: This mark denotes issues that may affect the printer’s operation.
: This mark denotes additional topics that complement the basic operating
procedures.
„ About illustrations used in this guide
This guide uses illustrations mainly for the CP710. Unless otherwise mentioned,
operations are also the same when using the CP510.
„ About camera descriptions in this guide
General camera descriptions in this guide refer to digital cameras or digital camcorders
compatible with the compact photo printer (CP710/CP510). However, in detailed
instructions, “camera” refers to “digital cameras”, and “power source” refers to “compact
power adapter” throughout this guide.
Disclaimer
z While every effort has been made to ensure that the information contained in this guide is
accurate and complete, no liability can be accepted for any errors or omissions. Canon reserves
the right to change the specifications of the hardware and software described herein at any time
without prior notice.
z No part of this guide may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language in any form, by any means, without the prior written permission
of Canon.
z Canon makes no warranties for damages resulting from corrupted or lost data due to a
mistaken operation or malfunction of the camera, the printer, the software, the CompactFlashTM
cards (CF cards), personal computers, peripheral devices, or use of non-Canon CF cards.
z Adobe is a trademark of Adobe Systems Incorporated.
z Macintosh, Mac OS and QuickTime are trademarks of Apple Computer Inc., registered in
the United States and other countries.
z Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
z CompactFlash is a trademark of SanDisk Corporation.
z MEMORY STICK, Memory Stick PRO, MEMORY STICK Duo and Memory Stick Pro Duo
are trademarks of Sony Corporation.
z MultiMedia Card is a trademark of Infineon Technologies AG.
z xD-Picture Card is a trademark of Fuji Photo Film Co., Ltd.
z SD Memory Card and miniSD Card are trademarks of SD Association.
z Bluetooth is a trademark of Bluetooth SIG, Inc., U.S.A. and is licensed to Canon Inc.
z Other names and products not mentioned above may be registered trademarks or
trademarks of their respective companies.
10
Safety Precautions
z Before using the devices, please ensure that you have read and understood the safety
precautions described below. Always ensure that the devices are operated correctly.
z The safety precautions noted on the following pages are intended to instruct you in the safe
and correct operation of the devices to prevent injuries or damage to yourself and other
persons.
Devices: Printer, Compact power adapter
Battery: Battery pack(sold separately)
WARNINGS
Do not play the supplied CD-ROM(s) in any CD player that does not support data CDROMs. Playing the CD-ROM(s) in an audio CD player (music player) could damage the
speakers. It is also possible to suffer from hearing loss from listening with headphones
to the loud sounds of a CD-ROM played on a music CD player.
Devices
z Do not disassemble or modify the devices.
z If the devices are dropped or the casing becomes damaged, do not continue operation.
z If the devices emit smoke or a burning odor, or show other signs of significant
malfunction, immediately unplug the power cord from the power outlet.
z Never rest liquid containers on top of the devices. If the exterior comes into contact with
liquids or salt air, wipe it dry with a soft, absorbent cloth.
z Do not drop or insert metallic or combustible objects into the devices.
Continued use of the equipment may result in fire or electric shock. Immediately turn the
printer power off and remove the printer battery or unplug the power cord from the power
outlet. Please consult your camera distributor or the closest Canon Customer Support Help
Desk.
z Do not touch metal parts of the devices or the power plug during thunderstorms.
Lightning strikes may produce lethal voltages within the devices. Keep clear of the devices
while thunderstorms are in progress.
z Do not use flammable solvents such as alcohol, benzene, or paint thinner to clean the
devices.
Continued use of the equipment may result in fire or electric shock.
11
Power
z Do not exceed the cable and power outlet ratings when operating this product. Do not
operate this product outside of the specified voltage rating. Check that the voltage of the
outlet is compatible with the devices before plugging them in.
z If the power cord becomes damaged (if internal wiring is exposed, etc.), immediately
unplug it from the power outlet.
z Be sure that the power cord is plugged all the way in.
z Do not damage, modify, or rest heavy objects on the power cord.
z Use only recommended power sources.
z Remove the power cord on a regular periodic basis and wipe away the dust and dirt that
collects on the plug, the exterior of the power outlet and the surrounding area.
z Do not handle the power cord if your hands are wet.
Continued use of the equipment may result in fire or electric shock.
Battery (sold separately)
z Do not place the battery pack near a heat source or expose it to direct flame or heat.
z The battery pack should not be immersed in water.
z Do not attempt to disassemble, alter or apply heat to the battery pack.
z Avoid dropping or subjecting the battery pack to severe impacts that could damage the
casing.
z Use only recommended battery pack and accessories.
Use of a battery pack not expressly recommended for this equipment may cause
explosions or leaks, resulting in fire, injury and damage to the surroundings. In the event
that a battery leaks and the eyes, mouth, skin or clothing contact these leaked substances,
immediately flush with water.
z Do not place anything, such as tablecloths, carpets, bedding or cushions, on top of the
battery charger while it is charging.
Heat will build up and could result in a fire.
z Before you discard a battery, cover the terminals with tape or other insulators to prevent
direct contact with other objects.
Contact with the metallic components of other materials in waste containers may lead to
fire or explosions.
Usage Location
z Do not place the devices on an unstable or tilted table or desk.
There is risk that the devices may fall and cause injury.
12
CAUTIONS
Devices
z Do not block the air vents on the printer.
z Do not rest heavy objects on the devices.
z Do not reach into internal parts of the devices except as specified in the operating
instructions.
Such conditions could lead to injury, fire, electric shock or other damage.
z Unplug the devices when you are not using them.
Leaving the devices plugged in during prolonged periods of non-use poses risk of electric
shock or fire.
z Do not remove the paper cassette from the printer while printing is in progress.
Paper moves back and forth in the cassette four times during printing. Placing your hand in
the way of moving paper may result in injury.
Power
z Do not move the devices while they are plugged in.
z Do not excessively bend or twist the power cord.
z Do not pull on the power cord.
Doing so may damage the power cord. Continued use of a damaged cord poses risk of fire,
electric shock or equipment failure.
Usage Location
z Do not use the devices in locations that are smoky, humid, dusty, or subject to strong
vibration.
z Do not leave the devices in places subject to strong sunlight or close to heating
equipment, such as the dashboard or trunk (boot) of a car.
The abovementioned can cause leakage, overheating or explosion, resulting in fire, burns
or other injuries. High temperatures may also cause deformation of the casing.
z Do not use the devices near an open flame.
Sheets ejected from the printer (onto the top of the paper cassette) may fall into the flame,
resulting in fire.
z Do not use the devices close to TV sets or AM radios.
Devices’ operation may adversely affect TV and radio reception.
13
Proper Usage and Handling
Usage Location
z Leave about 15 cm (6 in.) of clearance at the front and back of the devices and 10 cm (4
in.) of clearance on both sides.
Be sure to leave clearance around the paper-handling slot (at the rear) so that paper has
sufficient room to jut out from the slot during printing.
z Do not use near strong magnets or near devices that produce strong electromagnetic
fields.
Electromagnetic radiation from devices such as TVs and game machines, and strong
magnetic fields from devices such as speakers and large motors, may cause distortion in
printed images.
When Not In Use
z Attach the included dust cover to the rear of the printer.
If dirt or foreign objects enter the printer, print quality may deteriorate.
z Unplug the power cord from the outlet. If using the battery pack, remove it.
But please note that you should plug in and run the printer at least once every six months
to ensure that it remains functional.
When Planning Not to Use for an Extended Period
z When the printer is not in use, please remove the ink and paper cassettes from the
printer and store them.
Close the paper cassette’s top cover and store the paper cassette. Remove unused paper
from the paper cassette, return it to the bag and then into its original package. Store the
package horizontally.
Before Transporting
z Before transporting the printer, remove the paper and ink cassettes, close the paper
cassette cover and the ink cassette cover, and attach the dust cover to the rear of the
printer.
If dirt or foreign objects enter the printer, print quality may deteriorate.
z Pack the printer into an appropriate case for transport.
If a case is not available, wrap it with cloth or other protective material to protect against
scratches.
Avoid Condensation Related Problems
z You can avoid condensation by placing the devices (printer, ink cassette, paper
cassette, paper) in an airtight, resealable plastic bag and letting them adjust to
temperature changes slowly before removing them from the bag.
Moving the devices rapidly between hot and cold temperatures may cause condensation
(water droplets) to form on their external and internal surfaces.
14
If condensation Forms Inside the Devices
z Stop using the devices immediately.
Continued use may damage the equipment.
Printer: Wait until the water droplets have evaporated completely before resuming use.
Ink cassette, paper cassette, paper: Wipe off the water droplets and allow to return to
room temperature before resuming use.
Printer
z Please avoid turning the printer’s power on and off needlessly as the printer
initialization consumes ink.
There may not be enough ink left for the allotted sheets in the set.
z Never use volatile compounds or insecticides on the printer, and do not allow rubber or
vinyl material to remain in prolonged contact with the printer.
These materials may cause deformation of the printer’s casing.
z If the printer overheats, it will temporarily stop operating. This does not mean that the
printer has malfunctioned.
The printer will resume normal printing as soon as it cools down.
Temporary stoppages are most likely to occur in the following cases:
• When printing continuously.
• If the room is unusually warm.
• If the air vents on the back of the printer are blocked or if ventilation is inadequate.
Ink Cassettes
z Please use only the ink cassettes specified for use by Canon.
z Do not open the ink cassette cover while printing is in progress, and do not pull the ink
cassette out.
These actions may damage the printer.
z Do not touch or pull on the ink sheet.
There may not be enough ink left for the allotted sheets in the set.
z Do not handle the ink cassettes with wet or sweaty hands.
Paper Cassettes
z Do not apply excessive force to the paper
cassette.
Force or impact on the cassette may result in
paper jams or equipment damage.
Spring
z Do not bend or deform the spring located at the
rear of the middle cover of the paper cassette.
z Do not place any foreign objects in the print
output receptacle (on the top of the paper
cassette).
This area is for paper only.
15
Paper
z Please use only the paper types specified for use by Canon.
z Paper must be printed on the glossy side (the side without any printed markings).
Always load paper into the cassette with the glossy side up. Loading the paper the wrong
way may result in poor print quality, and in some cases may cause damage to the printer.
z Do not tear or bend the paper’s perforated edges before printing.
Tearing the paper’s perforated edges will cause the ink sheet to wind up automatically and
waste one print’s worth of ink. If this happens, there will not be enough ink left to print all
the paper sheets included in the kit.
z Do not use label sheets on which labels are partially peeled off.
z Do not touch the print side of the paper with
WRONG
your fingers.
RIGHT
Always hold the paper along the edges (outside
the perforated border).
Be sure that hands are dry before touching the
paper. Sharp objects will scratch the paper
surface. Keep the paper surface free from
fingerprints, dust, water droplets, etc.
z Do not write on the paper before printing.
Writing on paper before printing on it may result in malfunction.
z Do not touch the paper while it is being printed.
During printing, the sheet repeatedly moves back and forth along the top of the paper
cassette and in and out through the paper-handling slot. Please do not touch the sheet
during this process as this could damage the printer.
z Do not allow too many prints to accumulate in the print output receptacle.
Do not allow more than 9 sheets to accumulate in the print output receptacle.
z You may write on the paper with an oil-based pen, but to avoid smudging please allow
ink time to dry before touching it.
z Please avoid the following actions as they may result in color change, color fading or
color bleeding.
•
•
•
•
Sticking any type of adhesive tape onto the print surface.
Allowing print surfaces to come into contact with vinyl materials.
Applying alcohol or other volatile solvents to the print surface.
Leaving print surfaces tightly pressed against any other surfaces or objects for prolonged periods.
Prints
z If you wish to mount prints into an album, select an album with nylon-based sleeves, or
with propylene or cellophane sleeves.
Other types of sleeves may cause color loss or color bleeding.
z To avoid print quality deterioration, do not store your prints in the following types of
locations.
• Locations that reach temperatures above 40 °C (104 °F)
• Humid or dusty locations
• Locations exposed to direct sunlight.
z Color change may occur over time in accordance with conditions of storage. Canon
assumes no liability for color changes.
16
Battery (sold separately)
z Do not carry or store the battery pack with metal objects with sharp edges, such as
paper clips and pins. Always put the terminal cover on the battery pack’s terminal when
carrying it or before storing it.
z Remove the battery pack when the printer is not in use.
The battery pack continues to discharge a small amount when left in the printer even with
the power turned off. This shortens the battery life.
z The printer consumes the battery charge when the power is on even when a function is
not being used. To conserve the battery charge, be particularly attentive in turning the
power off.
z Although the battery pack’s maximum operating range is 5 to 40 °C (41 to 104 °F), the
optimal range is 10 to 30 °C (50 to 86 °F).
At cold temperatures, such as those experienced on ski hills, performance will temporarily
decline, reducing the usable time.
z If the battery status is low, the finished print may not be ejected into the print output
receptacle completely.
If this happens, gently pull out the paper.
z When the printer is not in use, remove the battery pack, replace its terminal cover and
store it in a cool place (30 °C/86 °F or less).
Charge it before using it again.
Charging the Battery (sold separately)
z This is a lithium ion battery pack so there is no need to completely use or discharge it
before recharging.
It can be charged at any charge state.
z It takes approximately 150 minutes to bring a fully discharged battery pack to a full
charge state (based on standard Canon testing criteria).
• Charge it within a temperature range of 5 to 40 °C (41 to 104 °F).
• The charging time varies according to the ambient temperature and charge state.
• The charge adapter may emit noises while charging. This is not a malfunction.
• Do not charge the battery pack for more than 24 continuous hours to avoid performance loss.
z You are advised to charge the battery on the day of use, or one day before, to ensure a
full charge.
Even charged battery packs continue to discharge naturally.
z Storing a fully charged battery pack for long periods of time (about 1 year) can shorten
its lifecycle or affect performance.
You are recommended to discharge the battery pack fully in the printer before storing it.
z If you do not use the battery pack for long periods of time, charge it fully and discharge
it fully in the printer at least once a year before returning it to storage.
z If the usable time of a battery pack diminishes substantially even when fully charged,
it should be replaced.
17
Read This First
Package Contents
In addition to the printer, the package contains the following accessories.
Paper Cassette
(Postcard size)
Standard Paper
(Postcard size, 5 sheets)
Ink Cassette
(Postcard size,
for 5 sheets)
Cleaner Stick*1
CP Printer Solution Disk
Compact Power Adapter
CA-CP200
Power Cord
Dust Cover*2
• User Guide (This Guide)
• Warranty Card*3
• Canon Customer Support Leaflet*3
*1 For
information about how to use the cleaner stick, refer to "Cleaning the Printer" (p. 57).
cover prevents dust from entering the printer. When the printer is not in use,
always attach it as shown in the figure.
*2 This
*3 Not
18
included in some regions.
Separately Sold Products
Paper Cassette PCL-CP100
L size
Paper Cassette PCC-CP100
Credit card size
Paper Cassette PCW-CP100
Wide size (100 x 200 mm (4 x 8 in.))
Color Ink/Paper Set KP-36IP
36 postcard size, standard sheets
Color Ink/Paper Set KP-108IP
108 postcard size, standard sheets
Color Ink/Paper Set KL-36IP
36 L size, standard sheets
Color Ink/Paper Set KC-36IP
36 credit card size, standard sheets
Color Ink/Paper Set KW-24IP
24 wide size (100 x 200mm), standard sheets
Color Ink/Full-Sized Label Set KC-18IF
18 credit card size, label sheets
Color Ink/Label Set KC-18IL
18 credit card size, multiple (8-label) sheets
Battery Pack NB-CP2L
Battery pack
Bluetooth Unit BU-20*
Enables wireless printing from devices that
support the Bluetooth standard.
Some products are not sold in some regions.
* It may be necessary to update the printer firmware in order to use Bluetooth.
Please check the following website for information on the newest firmware and how to
use and print with the Bluetooth unit.
http://web.canon.jp/Imaging/information-e.html
19
Components Guide
„ Compact Photo Printer SELPHY CP710
Front View
Power Button
Turns the printer’s power on/off. The
power button also lights to indicate the
printer status.
Ink Cassette Slot
The ink cassette is
inserted into this
compartment.
Green: Ready to print
Blinking green: Printing in progress
Orange: Charging the battery pack (sold separately)
Blinking orange: Battery pack (sold separately)
depleted
Red/Blinking red: Error (p. 61)
Ink Cassette
Compartment Cover
Retractable
USB Cable
The USB cable
for connecting the
camera is housed in
here.
Pull out the cable
and connect it to the
camera.
Paper Cassette Slot
The paper cassette loads into this
compartment.
Operation panel
LCD Monitor*
Displays images in
the memory card
when it is inserted,
and the operation
mode and details of
errors.
Paper Cassette
Compartment Cover
Indicator Lamp
Lights green when a memory card is
inserted, and blinks during
communications.
Card Slots
This is for inserting the memory
card or card adapter.
Back View
Battery Cover Lever
Used when the battery
pack (sold separately) or
battery cover is removed.
20
Operation Buttons
These are used for
selecting images in
the memory card
when it is inserted,
and for making print
settings.
Direct Print Port
Connects the interface cable
(included with the camera) to
the camera.
USB Port
Connects commercially
available USB cables to a
computer.
Air Vents
Paper-handling Slot
Paper extends out from this
slot while printing is in
progress.
PRINT/STOP Button
The periphery of this
button lights blue when
the power is turned on.
This button is out when
the ink cassette is not
loaded.
Battery Cover
DC IN Terminal
Connects to the compact power
adapter.
„ Compact Photo Printer SELPHY CP510
Front View
Power Button
Turns the printer’s power on/off. The
power button also lights to indicate
the printer status.
Green: Ready to print
Blinking green: Printing in progress
Orange: Charging the battery pack
(sold separately)
Blinking orange: Battery pack
(sold separately) depleted
Red/Blinking red: Error (p. 61)
Display Window*
You can check the name of the ink
cassette through the display window.
Lights blue when the power is turned on.
This display turns off when the ink
cassette is not loaded.
Ink Cassette Slot
The ink cassette is
inserted into this
compartment.
Retractable
USB Cable
The USB cable
for connecting the
camera is housed in
here.
Pull out the cable
and connect it to the
camera.
Ink Cassette
Compartment Cover
Paper Cassette Slot
The paper cassette loads into this
compartment.
Paper Cassette
Compartment Cover
Back View
Battery Cover Lever
Used when the battery
pack (sold separately) or
battery cover is removed.
Direct Print Port
Connects the interface cable
(included with the camera) to the
camera.
USB Port
Connects commercially
available USB cables to a
computer.
Air Vents
Paper-handling Slot
Paper extends out from this
slot while printing is in
progress.
Battery Cover
DC IN Terminal
Connects to the compact power
adapter.
* The LCD monitor or the display window is covered with a thin plastic film for protection
against scratches during shipment. Remove it before using the printer.
21
This Printer Allows You to Do the Following
Immediately print images
taken on your camera
Select and print images
from a memory card
(CP710 only)
Print from a computer
Connect via the built-in
retractable USB cable.
Insert the memory card into
the appropriate memory card
slot.
Software must be installed,
and printer connected to the
computer by the USB cable
(sold separately).
Before you connect the
printer to the computer,
be sure to install the
software following the
procedure on page 42.
22
You can make various size prints
L size paper cassette
(sold separately)
Credit card size paper
cassette
(sold separately)
Postcard size paper
cassette
• You can easily make
L size prints with photo
prints.
• You can make fullsize stickers or
divided into eight
equal-size areas
using label stickers.
• You can make
original postcards by
printing on postcard
size paper.
Wide size paper
cassette
(sold separately)
• Make borderless wide size prints.
Borderless printing is not supported by some
cameras.
You can alter images with a computer and lay them out in various ways
• You can easily
select layouts for
printing.
Season’s Greetings
• You can easily combine images taken
using the camera’s Stitch Assist function
on a computer.
• Images can be laid out
and printed any way
you like.
• You can add frame images or captions,
and lay out images as you like.
23
Printing Procedure and Reference Guides
Preparing
Connect the printer to
the camera for printing
User Guide (This Guide) p. 26
Printing from a
computer
Printing from memory card (CP710 only)
Installing the Software and the Printer Driver
User Guide (This Guide) p. 41
Before you connect the printer to a
computer, you must install the printer
driver from the CP Printer Solution
Disk. Be sure to install the software
before connecting the printer to the
computer using the procedure on
page 42.
When an Error Occurs and Troubleshooting
24
Connecting
Printing
User Guide (This Guide) p. 31
User Guide (This Guide) p. 31
Camera User Guide
Direct Print User Guide
Camera User Guide
Direct Print User Guide
When using non-Canon digital cameras,
refer to the user guide that came with your
camera.
User Guide (This Guide) p. 34
User Guide
(This Guide) p. 36, 37, 38
User Guide (This Guide) p. 48
Printer Software Guide
(PDF Format)
Troubleshooting or Error Messages:
User Guide (This Guide) p. 58, 61
Contacting us for repair:
Canon Customer Support
Leaflet
Printer Software Guide (PDF Format)
25
Let’s Prepare
„ Preparing Your Ink Cassette/Paper Sets and Paper Cassette
Prepare the paper and ink/paper cassettes to match the size of the paper you are
printing.
There are several types of paper and paper/ink cassettes.
If the set is not correct, you will not be able to print.
Please check the sets and the names of their components in the table below.
Paper Cassette Name
Paper Size
Paper Cassette
Name
Ink Cassette Name
Ink Cassette Name*4
L size*1
(89 x 119 mm)
(3.5 x 4.7 in.)
Credit card size*2
(54 x 86 mm)
(2.1 x 3.4 in.)
Postcard size
(100 x 148mm)
(4 x 6 in.)
Wide size*3
(100 x 200 mm)
(4 x 8 in.)
*1 The
paper cassette PCL-CP100 (sold separately) is required.
paper cassette PCC-CP100 (sold separately) is required.
*3 The paper cassette PCW-CP100 (sold separately) is required.
*4 The design of the label on your ink cassette may slightly differ from the examples below. XX in the
examples indicates the number of sheets that can be printed.
*2 The
Separately Sold Products
"Separately Sold Products" (p. 19)
When opening a color ink/paper set (full-sized label set, label set), check the contents. If
something seems to be missing or appears to be damaged, contact the dealer for
assistance.
26
„ Loading the Ink Cassette
Proper Handling of Ink Cassettes
1
"Ink Cassettes" (p. 15)
Take up the slack in the
cassette’s ink sheet.
z If the ink sheet is slack, push in on the
sprocket
in the figure, and turn it
gently to take up the slack until the ink
sheet straightens out.
Ink sheet
It will not be possible to print to all of the
paper if you overwind the ink sheet.
2
Push in on the
sprocket and turn
gently.
Open the ink cassette
compartment cover, and insert
the ink cassette all the way into
the compartment.
Clip
2
z Push the cassette all the way in, so that it
clicks into place.
z When you are ready to remove the ink
cassette, lift the clip and pull the cassette
out.
Be careful to avoid touching or pulling on
the ink sheet when inserting the ink
cassette.
3
1
Arrow side facing up
Close the ink cassette compartment
cover.
You can check the name of the ink cassette
loaded in the printer.
CP710: Viewing the LCD monitor display (p. 35)
CP510: Viewing the display window on the top of
the printer (p. 21)
Do not reuse empty ink cassettes. Attempting to reuse an empty ink cassette may result in
malfunction or damage to the printer.
27
„ Loading the Paper into the Paper Cassette
Do not insert more than 18 sheets in the paper cassette. Do not insert more than 12
sheets of wide size paper (100 x 200 mm (4 x 8 in.)) in the paper cassette.
Proper Handling of Paper Cassettes
"Paper Cassettes" (p. 15)
Proper Handling of Paper
"Paper" (p. 16)
Please use specified paper types only.
1
Open the paper cassette’s top cover and middle cover.
z Open the top cover, then push the middle cover in the direction of the arrow and lift it up.
Middle cover
Top cover
2
Fan the paper stack properly and
place the paper into the paper
cassette, with the printable side
(glossy side) facing up.
Paper
(Glossy side up)
z Insert the postcard size paper with the
glossy side up and the address/stamp
side next to the middle cover as shown in
the figure.
z Do not touch the glossy side of the paper
(to avoid fingerprints) when you fan the
paper stack.
L size*
(Address/stamp side
next to the middle
cover)
Credit card size*
Glossy side up
Wide size*(100 x 200 mm(4 x 8 in.))
Glossy side up
28
*Sold separately
3
Place the middle cover back to its
original position.
z After pulling the middle cover down, slide it in
the direction of the arrow until it clicks back into
place.
z Do not close the top cover.
Printed or fed paper is coated even when nothing is printed on the paper. Therefore,
never reuse the printed or fed paper for printing. Reused paper may stick to the ink
sheet, resulting in damage to the printer.
„ Loading the Paper Cassette
1
Open the paper cassette
compartment cover.
2
Push the paper cassette all
the way into the paper
cassette slot.
Middle cover
closed
z Be sure the paper is set correctly
before pushing the cassette in.
z Insert the paper cassette evenly so
that it slides over the bottom of the slot
entrance.
Top cover open
•The printer outputs the finished prints into
the receptacle onto the top of the printer
cassette (top of the middle cover or inside
of the top cover). Be sure to close the
middle cover and open the top cover so
that output can proceed normally.
•Do not allow more than 9 sheets to
accumulate in the print receptacle. Do not
allow too many prints to accumulate.
Print receptacle
Do not remove the paper cassette while feeding, printing, or ejection is in progress.
29
„ Placing the Printer
Usage Location
"Usage Location" (p. 14)
Refer to the figure below when placing the printer. Numbers in the figure correspond to
the steps in the procedure below.
1
3
15 cm (6 in.) at the front and
back of the device
and 10 cm (4 in.) on both sides
or more of open space
2
To power outlet
Compact power
adapter
4
The battery pack (sold separately) also can be used (p. 55).
30
1
Place the printer on a flat area.
2
Connect the supplied power cord to the supplied Compact Power
Adapter CA-CP200.
3
Insert the plug in a power outlet.
4
Connect the compact power adapter cable to the printer.
Connecting to a Camera for Printing
Connecting to a Camera for Printing
Connect the printer to the camera by the built-in retractable USB cable and start printing.
This section explains the flow of printing operations with Canon cameras*.
For more details, refer to your Camera User Guide or Direct Print User Guide.
*In
other cases, please refer to the "Printing with Non-Canon Digital Cameras" (p. 66).
Make sure that the memory card is not inserted into the printer and that the printer is not
connected to the computer.
z Use Canon cameras compatible with CP710/CP510, and non-Canon cameras compatible
with PictBridge can also be connected.
z We recommend that you also connect the camera’s compact power adapter (sold
separately or included with the camera) when using the camera with your printer. If you
wish to run the camera on battery pack or batteries power, be sure that battery pack is
fully charged or the batteries are fresh.
z Some camera models do not come with a compact power adapter. For details, please see
the System Map that came with your camera.
1
Pull out the retractable USB cable
from the printer, and connect to the
camera.
z You can also use the USB cable included
with the camera. In this case, connect the
DIGITAL terminal on the camera to the direct
print port (p. 20, 21).
z To retract the USB cable, pull the cable
gently towards you and release the cable.
z The cable can be pulled out up to about 25 cm
(9.8 in.). Note that pulling the cable out
beyond this length may damage it.
2
Press the printer’s power button.
3
Turn the camera’s power on and
display the images.
z The power button lights green once the printer powers up.
z Check that the
(PictBridge) /
(Canon
Direct Print) icon is displayed in the upper left
corner of the LCD monitor.
When the icon is not displayed
(p. 58)
"Troubleshooting"
z Some camera models automatically power up when
the cable is connected to the printer. The icon then
displays on the LCD monitor.
31
4
Display the images to be printed and press the SET or SELECT
button.
z If your camera has a
(Print/Share) or
immediately after you press the
or
5
(Direct print) button, printing starts
button (Step 5 is not necessary).
Select [Print] and press the SET or
SELECT button.
z Printing starts. During printing, the printer’s power
button blinks green.
z The camera returns to the playback screen once
printing is successfully completed.
If printing does not start, check the camera’s LCD
monitor for any messages (p. 61).
The screen shot differs depending
on the model of your camera.
„ Disconnect the camera
Before you disconnect the camera from the printer, turn off the printer by holding down
the power button until the green indicator goes out.
„ Printing on the separately sold wide size (100 x 200 mm
(4 x 8 in.)) paper
The printing area may vary depending on the camera use.
If
appears in step 3 on page 31
Printed on the whole card.
The upper and lower portions of an image
are trimmed.
If
32
If
appears in step 3 on page 31
Printed on the 100 x 150 mm (4 x 6 in.)
portion of the card.
Nothing is printed on this portion
so you can write your message with an oil-based
pen.
appears in step 3 on page 31, select [Default] on the paper size setting screen.
Printing from Memory Card (CP710 only)
Insert the memory card into the printer so that you can print images stored on the
memory card.
Make sure that the camera or computer is not connected to the printer.
Clearer printing results can be obtained when printing from a memory card by optimizing the
information stored in the camera when the photo was taken.
To turn image optimization off, press and hold the DATE button and then press the PRINT/
STOP button to start printing (p. 35).
Compatible Memory Cards
Memory cards that can be directly inserted
z SD memory card
z MultiMedia Card
Memory cards that require a specific adapter
z miniSD card
*1
z CompactFlashTM (CF)
card
z Microdrive
z xD-Picture Card
*TYPEI/TYPEII (Only 3.3 V
cards are compatible.)
z Memory Stick
z Memory Stick PRO
z Magic Gate Memory
Stick
*2
z Memory Stick Duo
z Memory Stick PRO Duo
z Magic Gate Memory Stick Duo
*1
*1 Use the specific adapter for the card.
*2 Purchase the CompactFlash Card Adapter for xD-Picture Card separately.
z This printer supports images taken with a camera compatible with the Design rules for
Camera File system (Exif compliant) and DPOF (ver 1.00 compliant).
z Images saved on non-compatible memory cards might not be able to be read or data may be
corrupted. Use a memory card that is compatible with the camera. For details, refer to the
camera’s user guide included with the camera.
z Format memory cards on the camera. Memory cards should not be formatted on computers.
z Images that have been edited on a computer might not be displayed or printed successfully.
33
Inserting Memory Cards
Do not load two or more memory cards at the same time.
1
Press the printer’s power button.
z The power button lights green once the printer powers up.
z After a while, the startup screen is displayed on the LCD monitor.
2
Push the memory card all the way into the card slots.
z The memory card will protrude slightly from the card slots.
z The indicator lamp blinks green, and the images on the memory card are displayed on the
LCD monitor.
Insert memory cards with the label side up.
CF card/
SD memory card/
Microdrive/
Multimedia card/
*
xD-Picture Card miniSD card*
Memory Stick/Memory Stick Duo*/
Memory Stick PRO/Memory Stick PRO Duo*/
Magic Gate Memory Stick/
Magic Gate Memory Stick Duo*
*The exclusive adapter is required (p. 33).
LCD monitor
"Main Details Displayed on the LCD Monitor" (p. 35)
Removing Memory Cards
As shown in the figure on the right, grip the protruding
section of the card, and remove it from the card slot.
Example:CF card
Do not remove memory cards or turn the printer off while the indicator lamp is blinking.
34
About LCD Monitor and Operation Buttons
LCD Monitor
Displays images on the
memory card, and details
that have been set using
the buttons.
button: Displays the
previous image.
button: Displays the next
image.
button: Increments the
number of prints.
button: Decrements the
number of prints.
PRINT/STOP Button
Starts printing. Printing is
canceled when this button
is pressed during printing.
MODE Button
Selects the print
operation mode.
SELECT
LAYOUT Button
DATE Button
Selects the print layout
(p. 39).
Selects whether or not
to print the date that you
took the photograph.
When you print the date,
specify the format of the
date (p. 40).
Borderless
Printing Selected Images
(p. 36).
The date is not
printed.
Bordered
ALL
Print all of the images on
the memory card one
image at a time (p. 37).
Year/Month/
Day
8 stickers
Month/Day/
Year
DPOF
Index
Prints DPOF by specified
images (DPOF) (p. 38)
The file No. can
also be printed.
Day/Month/
Year
„ Main Details Displayed on the LCD Monitor
File No.
Selected image
Print preview
Number of prints of the currently
displayed image
Number of sheets to be printed
Current operation
mode
Layout setting
Error screen
Kind of ink cassette currently
loaded in the printer
Date setting
"Error Messages" (p. 61)
35
Printing Selected Images (SELECT)
Select a specific image in the LCD monitor and print that image.
The required number of specific images can be printed together.
Buttons available for this function
button
button
button
button
1
Turn the printer on, and insert the memory card
into the card slot (p. 34).
z The
(SELECT) screen is displayed. If the
screen is
not displayed, press the MODE button and display
.
z You can specify the layout with the LAYOUT button (p. 39).
z You can print the date with the DATE button (p. 40).
2
Press the
button or the
the image to print.
button to display
3
Press the
button or the
the number of prints.
button to specify
Number of prints
4
36
Repeat steps 2 and 3.
To cancel printing of a specified image, display the desired image, and press the
button to set the number of prints to “0”.
5
Check the setting on the LCD monitor.
Print preview (when 8
stickers are specified in
LAYOUT (p. 39))
Make sure that the paper cassette contains the
required number of sheets of paper.
6
Press the PRINT/STOP button.
z Printing starts. During printing, the printer’s power button blinks green.
Printing All Images (ALL)
Print a single copy of all the images on the memory card at a time.
Buttons available for this function
1
Turn the printer on, and insert the memory card into the card slot
(p. 34).
2
Press the MODE button to display
(ALL).
z You can specify the layout with the LAYOUT button (p. 39).
z You can print the date with the DATE button (p. 40).
3
Check the setting on the LCD monitor.
Print preview
(when 8 stickers are specified in LAYOUT (p. 39))
Number of sheets to be printed
Make sure that the paper cassette contains the
required number of sheets of paper.
4
Press the PRINT/STOP button.
z Printing starts. During printing, the printer’s power button blinks green.
37
Printing by specified camera settings (DPOF)
You can make prints according to the DPOF (Digital Printer Order Format) setting
specified on the camera.
Buttons available for this function
z The date setting complies with the DPOF information. The date cannot be set with the
DATE button.
z Layout cannot be specified.
1
Turn the printer on, and insert the memory card into the card slot
(p. 34).
2
Press the MODE button to display
z
(DPOF).
(DPOF) cannot be selected when a DPOF-specified image is not found on the
memory card.
The “Print type” set on the camera is displayed.
Both:
Standard:
Index:
Make sure that the paper cassette contains the required number of sheets of paper.
3
38
Press the PRINT/STOP button.
z Printing starts. During printing, the printer’s power button blinks green.
Specifying the Layout
Specify the print layout.
You can select from bordered/borderless, 8 stickers or index (INDEX).
Bordered
Borderless
Index
8 stickers
The file No. can also be
printed.
If you set the print operation mode to ALL and layout to INDEX, you can print a list of all the
images on the memory card.
1
Select the required operation mode, and press the LAYOUT button
several times to select layout.
Borderless
2
Bordered
8 stickers
Index
Check the setting on the LCD monitor.
z The number of sheets of paper to be printed sometimes changes according to the
layout.
Example: when “8
stickers” is selected
Number of sheets to be
printed (1)
Selected layout (8 stickers)
39
Printing the Date
Select whether or not to print the date that you took the photograph. When you print the
date, specify the format of the date.
1
Select the required operation mode, and press the DATE button to
select the date format.
The date is
not printed.
:Year/Month/Day
The date is printed.
:Month/Day/Year
:Day/Month/Year
40
Connecting to a Computer for Printing
System Requirements
Please install the software on a computer meeting the following minimum requirements.
„ Windows
OS
Computer Model
CPU
RAM
Interface
Free Hard Disk
Space
Display
Windows 2000 Service Pack 4
Windows XP (Including Service Pack 1 and Service Pack 2)
The above OS should be pre-installed on computers with built-in USB
ports.
Pentium 500 MHz or higher processor
256 MB or more
USB
• Canon Utilities
- Easy-PhotoPrint: 65 MB or more
- PhotoStitch: 40 MB or more
- PhotoRecord: 100 MB or more
• Canon SELPHY CP710/CP510 Printer Driver: 4 MB or more (the
amount of free space required for installation)
1,024 x 768 pixels/High Color (16 bit) or better
„ Macintosh
OS
Computer Model
CPU
RAM
Interface
Free Hard Disk
Space
Display
Mac OS X (v10.2 - v10.3)
The above OS should be pre-installed on computers with built-in USB
ports.
PowerPC G3/G4/G5
256MB or more
USB
• Canon Utilities
- ImageBrowser: 200 MB or more
- PhotoStitch: 40 MB or more
• Canon SELPHY CP710/CP510 Printer Driver: 4 MB or more (the
amount of free space required for installation)
1,024 x 768 pixels/32,000 colors or better
z A CD-ROM drive is required to install the software.
z Even when system requirements are met, not all computer functions can be guaranteed.
z All procedures performed with a connection to a USB 2.0 compliant board are not
guaranteed.
z Macintosh software cannot be used on disks formatted in the UFS (Unix File System)
format.
41
Installing the Software and the Printer Driver
The CP Printer Solution Disk contains software that your computer will require for
printing. Install the software and the printer driver according to the following steps.
The instructions in this section are intended for Windows XP and Mac OS X (v10.3). If you
are using another version of OS, actual screen contents and procedures may differ slightly
from those indicated here.
Windows
z Be sure to install the software and the printer driver before connecting the printer to the
computer.
z Be sure to log on with Administrator privileges (computer system administrator) when
installing the software.
1
Close any programs that are running.
2
Place the CP Printer Solution Disk in the CD-ROM drive.
z The installer panel automatically appears.
If the installer panel does not automatically appear, use the following procedure to start
it.
- For Windows XP, click the [Start] button and select [My Computer], double-click the
CD-ROM icon in the next window.
- For Windows 2000, double-click the [My Computer] icon on the desktop, and doubleclick the CD-ROM icon in the next window.
3
Click the Application Software [Install] button and click [Next].
Installer panel
42
4
Select [Easy Installation] as the setup type and click [Next].
5
Follow the screen messages to proceed. When a dialog box
appears instructing that the installation is complete, click [Finish].
z Select [Custom Installation] to select programs for individual installation.
z Restart your computer when a dialog box appears instructing you to do so.
Next, install the printer driver to your computer.
6
Click the CP Printer Driver [Install] button.
z If the installer panel does not automatically appear, use the following procedure to start
it.
- For Windows XP, click the [Start] button and select [My Computer], double-click the
CD-ROM icon in the next window.
- For Windows 2000, double-click the [My Computer] icon on the desktop, and doubleclick the CD-ROM icon in the next window.
7
Click the printer you are using and click [Next] when the following
screen is displayed.
8
Click [Yes] if you consent to all the conditions of the software
license agreement.
z The installer starts.
43
9
When the screen below appears, connect the printer to the
computer with a commercially available USB cable and turn the
printer’s power on.
Refer to "Connecting the Printer to Your Computer" (p. 48) on how to connect.
z Follow the screen messages to proceed.
a dialog box appears instructing that the installation is
10 When
complete, click [Finish].
z Restart your computer when a dialog box appears instructing you to do so.
the computer desktop displays, remove the CP Printer
11 When
Solution Disk from the CD-ROM drive.
44
Macintosh
Be sure to install the software and the printer driver before connecting the printer to the
computer.
1
Quit any programs that are running.
2
Place the CP Printer Solution Disk in the CD-ROM drive, and
double-click the [Canon CP Printer Installer] icon in the CD-ROM.
z The installer panel appears.
3
Click the Application Software [Install] button.
Installer panel
4
Select [Easy Installation] and then click [Next].
5
Follow the screen messages to proceed. When a dialog box
appears instructing that the installation is complete, click [OK].
z Select [Custom Installation] to select programs for individual installation.
Next, install the printer driver to your computer.
45
6
Click the CP Printer Driver [Install] button.
7
Click the printer you are using.
8
Click [Agree] if you consent to all the conditions of the software
license agreement.
z The installer starts.
9
Select [Easy Install] and then click the [Install] button.
z Follow the screen messages to proceed.
z Restart your computer when a dialog box appears instructing you to do so.
the computer desktop displays, remove the CP Printer
10 When
Solution Disk from the CD-ROM drive.
Next, register your printer on the Printer List.
the printer to the computer with a commercially available
11 Connect
USB cable and turn the printer’s power on.
For directions on connecting the printer, see "Connecting the Printer to Your Computer" (p. 48).
46
the [Printer Setup Utility] or [Print Center] icon in
12 Double-click
[Applications] [Utilities] folder.
z The Printer List window appears.
13 Click the [Add] button.
[USB], select the printer name, and then click the [Add]
14 Select
button.
15 Close the window by clicking
in the upper left-hand corner.
47
Connecting the Printer to Your Computer
„ Notes about connection
Before connecting the printer to a computer, make sure that the memory card is
not inserted into the printer and that the printer is not connected to the camera.
zThe printer may not function properly.
When using the USB cable, be sure to connect the printer directly to your
computer.
zIf you connect the USB cable via a USB hub, the printer may not function
properly.
Do not use other USB devices (with the exception of a USB mouse or USB
keyboard) with the printer. The printer may not function properly.
zDisconnect the other USB devices from your computer and then reconnect the
printer.
Do not connect two or more direct print compatible printers (all CP series
printers) to the same computer.
zThe printers may not function properly.
For Windows, when connecting the printer to your computer, we recommend that
you connect it to the same USB port you used to install the printer driver.
zIf you connect the printer to a different USB port, Windows may create a copy
of the printer driver. This depends on your Windows version and the printer
driver, and does not affect the operation of the printer.
To delete a copy of the printer driver, proceed as follows:
1.Disconnect the USB cable from your computer.
2.Delete the copy of the printer driver as follows (do not use the uninstaller.)
(1) For Windows XP, click the [Start] button and select [Control Panel] [Printers
and Other Hardware] [Printers and Faxes].
For Windows 2000, click the [Start] button and select [Settings] [Printers].
(2) Right-click the copy of the printer driver and then select [Delete] on the
shortcut menu.
3. Restart your computer. Connect the printer to the USB port you used to install
the printer driver.
z Do not put your computer into the standby mode (or sleep mode) while the printer is
connected to a USB port.
z If you accidentally do so, do not disconnect the USB cable from your computer while it is in
the standby mode; instead, leaving the USB cable connected, first return your computer to
its normal mode. If you remove the USB cable while your computer is in the standby
mode, your computer may not be able to return to its normal mode. For details on your
computer’s standby mode, refer to the documentation provided with your computer.
48
1
Connect one end of a commercially available USB cable to the USB
port on the printer, and the other end to a USB port on your
computer.
z There is no need to turn off the printer or your computer.
z When connecting the printer to your computer, make sure the connectors on the ends of
the USB cable match the ports on the printer and your computer.
z For the location and direction of your computer’s USB port, refer to the documentation
provided with your computer.
USB port
on computer
USB cable
When disconnecting the USB cable, you do not need to turn off the printer or your computer.
49
Software Manuals
Adobe Reader or Adobe Acrobat Reader must be installed to view the PDF Manuals. If this
software is not already installed in your computer, access the following web site and
download the software.
http://www.adobe.com/products/acrobat/readstep2.html
„ Printer Software Guide
This guide describes how to print using the software installed to your computer.
1
Install the software from the CP Printer Solution Disk.
(Windows
p. 42, Macintosh
p. 45)
z The Printer Software Guide will automatically be installed to your computer, and the
[CP Printer Guide] icon appears on the desktop.
2
Double-click
[CP Printer Guide].
z Printer Software Guide will be displayed.
CP Printer Guide
z If you need the Printer Software Guide in a different language:
Windows/Macintosh: Double-click the desired language folder in the [README] folder
on the CD-ROM, then double-click [CP PRINTER USER
GUIDE]
z The ImageBrowser Software User Guide describes in detail the functions and operations
of the ImageBrowser software for the Macintosh. This guide can be downloaded from the
following web site if it is required.
http://web.canon.jp/Imaging/information-e.html
50
Uninstalling the Software
Uninstall the software when it is no longer needed, or if a problem occurs and uninstalling
becomes necessary. Note that if you uninstall the software, you will not be able to use it
anymore.
Windows
The instructions in this section are intended for uninstallation of Easy-PhotoPrint.
1
Click the [Start] button and select [All Programs] or
[Programs] [Canon Utilities] [Easy-PhotoPrint]
PhotoPrint Uninstall].
[Easy-
z Follow the screen messages to proceed.
z You can use the same procedure to uninstall PhotoStitch.
z To uninstall PhotoRecord, click the [Start] button and select [All Programs] or
[Programs] [Canon PhotoRecord] [PhotoRecord Uninstall].
Macintosh
1
Drag the application’s folder (the folder in which it was installed)
into the Trash.
2
Empty the Trash.
Please be careful not to accidentally delete any folders with downloaded images that may
be contained within the application folder.
51
Uninstalling the Printer Driver
Uninstall the printer driver if it is no longer needed, or if a problem occurs and uninstalling
becomes necessary. Note that if you uninstall the printer driver, you will no longer be able to
use the printer to print.
Be sure to follow the procedures described in this section to uninstall the printer.
Windows
52
1
Click the [Start] and select [All Programs] or [Programs]
SELPHY CP XXX] [Uninstall].
2
Select the printer you will uninstall and click [Next].
z Follow the screen messages to proceed.
[Canon
Macintosh
1
Place the CP Printer Solution Disk in the CD-ROM drive, and
double-click the [Canon CP Printer Installer] icon.
z The installer panel appears.
2
Click the CP Printer Driver [Install] button.
3
Click the printer you wish to uninstall.
4
Click [Agree] if you consent to all the conditions of the software
license agreement.
5
Select [Uninstall], and then click the [Uninstall] button.
6
Follow the screen messages to proceed. When a dialog box
appears instructing that the installation is complete, click [Quit].
Remove the CP Printer Solution Disk from the CD-ROM drive.
Next, delete the printer from the Printer List.
7
Double-click the [Printer Setup Utility] or [Print Center] icon in
[Applications] [Utilities] folder.
z The Printer List window appears.
53
54
8
Select the printer you uninstalled, and then click the [Delete]
button.
9
Close the window by clicking
in the upper left-hand corner.
Using the Battery Pack (sold separately)
You can print outdoors or at locations without a power outlet by installing the battery pack
NB-CP2L (sold separately).
Proper Usage and Handling of the Battery Pack
"Battery (sold separately)" (p. 17)
z The battery pack NB-CP1L (sold separately) cannot be used.
z Do not use the battery pack in products other than those recommended by Canon.
Attaching and Charging the Battery Pack
Use the printer for charging the battery pack.
Install the battery pack NB-CP2L on the printer to charge the battery pack.
1
Remove the battery pack’s
terminal cover.
When the battery pack is not in use,
always store it with its terminal cover
on.
2
Terminal cover
Press the battery cover lever
down and remove the battery
cover.
1
2
3
Install the battery pack on the
printer.
z Slide the battery pack into place, in the
direction of the arrow, and push it in until
it clicks into place.
To remove the battery pack, push the
battery cover lever down and pull the
battery pack out. Replace the battery
cover afterwards.
2
1
55
4
Attach the power cord to the
Compact Power Adapter CACP200 and plug it into a
power outlet.
To power outlet
Compact power
adapter
5
Connect the compact power
adapter cable to the printer.
Power cord
Power button
z The power button lights orange while
charging and turns off once the battery
pack is fully charged.
If the power button is pressed and the
printer’s power turns on while
charging the battery pack, charging
will stop. Pressing the power button
again will turn off the printer and
charging will resume.
6
Compact power adapter cable
Disconnect the compact
power adapter cable from the
printer once charging is
complete.
z The battery pack can be used to
power the printer.
When the battery pack is used to power the printer, the printer will automatically turn off if it
is idle for 5 minutes or more.
„ Battery Status
If battery status is low, the printer’s power button blinks orange.
Also, the camera’s LCD monitor or printer’s LCD monitor (CP710 only) display an error
message (p. 62).
Switch the battery pack for a fully charged one or recharge the battery pack.
56
Appendix
Cleaning the Printer
„ Cleaning Inside the Printer
If faint stripes appear in the printed image, a probable cause is that dust has
accumulated inside the printer. Remove any dust using the cleaner stick included with
your printer.
1
Remove the ink cassette.
2
Insert the cleaner stick in
the direction of the arrow
and with the arrow on the
cleaner stick facing up.
Push it in completely and
slide it in and out of the
printer 2 or 3 times.
„ Cleaning the Printer Casing
Wipe the casing with a soft dry cloth. If stronger cleaning is required, wipe first with a
cloth moistened with a diluted neutral solvent, then wipe again with a soft dry cloth. If you
use a chemical cleaning cloth, read the instructions that come with it and observe all
indicated precautions.
Never use benzene, paint thinner, or other volatile solvents to clean the printer. Volatile
solvents may cause deformation or peeling of the printer’s casing.
„ Cleaning the Back of the Printer
Keep the air vents clean and free of dust. Clean the vents as necessary. Dust that enters
the printer through the vents may land on the ink sheet, resulting in poor print quality.
If the ink sheet becomes dusty, remove the ink cassette and replace it with a new one.
57
Troubleshooting
If the printer does not seem to be working properly, run through the checks below to see
if you can identify and correct the problem. If you are not able to solve the problem,
please call your dealer or contact a Canon Customer Support help desk for assistance.
The printer has no power.
The compact power adapter
or power cord is not correctly
connected.
z Be sure that the compact power adapter and power cord
are connected correctly. Be sure that the power cord is
plugged into a standard power outlet.
The printer’s power button is blinking red.
There is a malfunction in the
printer.
z Turn the printer’s power off and turn it on again.
The
(PictBridge)/
(Canon Direct Print) icon does not display in the upper left
corner of the LCD monitor.
The cable is not correctly
connected.
z Connect the cable correctly (p. 31).
The printer’s power is off.
z Turn the printer’s power on (p. 31).
Your camera’s firmware is
z Please check the Canon BeBit website (http://
incompatible with this printer.
web.canon.jp/Imaging/BeBit-e.html), or your regional
Canon website, for information or to download compatible
firmware.
Printing from the memory
card is in progress or printing
connected to a computer is
in progress.
z Wait until the print outputted.
The printer does not print.
58
The printer is not correctly
connected to the camera.
z Connect the cable correctly (p. 31). If the connection is
correct, the
or
icon will appear on the camera’s
LCD monitor.
The camera’s batteries are
depleted.
z Replace with fully charged battery pack or a fresh
batteries, or plug the camera into a power outlet (using the
camera’s optional compact power adapter).
The ink cassette is not
loaded correctly.
z Load the ink cassette correctly (p. 27).
Too much slack in the ink
cassette’s ink sheet.
z Take up the slack (p. 27).
The paper cassette is not
pushed all the way in.
z Load the paper cassette correctly (p. 29).
The printer has overheated.
z Wait for the printer to cool down.
Printing stopped midway.
The printer is not correctly
connected to the camera.
z Connect the cable correctly (p. 31).
The printer’s power button lights red without the camera’s LCD monitor displaying
any error message.
There is a malfunction in the
printer.
z Remove the paper from the paper-handling slot and take
up any slack in the ink sheet. Turn the printer’s power off
and turn it on again.
Print quality is not good.
You are not using the correct
paper type.
z Use the designated paper type.
Paper is loaded with the
wrong side up.
z Load the paper correctly (p. 28).
The ink sheet or paper is
dirty.
z Use a clean ink sheet and clean paper.
Condensation has formed
inside the printer.
z Wait for condensation to evaporate (p. 15).
Printed images are distorted.
The printer is too close to a
TV, video game machine, or
other electromagnetic
source.
z Move the printer so that it is at least 1 meter (3.3 ft.) away
from the electromagnetic source.
The printer is too close to a
stereo speaker, large motor,
or other strong magnetic
source.
z Move the printer away from the strong magnetic source.
There is not enough ink left for the allotted sheets in the set.
You turned the printer’s
power on and off repeatedly.
z Please avoid turning the printer’s power on and off
needlessly.
You pulled on the ink sheet.
z Do not pull on the ink sheet by force.
You tore or bent the paper’s
perforated edges before
printing.
z Do not tear or bend the paper’s perforated edges.
You removed the ink
cassette when paper run out
while the printer was printing
more than one sheet of
paper.
z Load paper into the paper cassette without removing the
ink cassette.
Nothing happens when the camera’s
,
or SET button is pressed.
The printer has overheated.
z Wait for the printer to cool down.
Printing is in progress.
z Wait for the printer to finish printing.
59
Frequent paper jams.
The paper cassette is
overloaded.
z Do not load more than 18 sheets of paper into the
cassette. Do not insert more than 12 sheets of wide size
paper (100 x 200 mm (4 x 8 in.)) in the paper cassette.
The print output receptacle is
too full.
z Do not allow more than 9 sheets to accumulate in the
receptacle.
Paper is creased or curled.
z Do not use paper that is creased or curled.
Faint stripes appear in the print.
Dust has accumulated inside
the printer.
z Remove the dust inside the printer using the cleaner stick
(p. 57).
“?” instead of the image is displayed on the LCD monitor. (CP710 only)
“?” is sometimes displayed
depending on the image.
z Printing is sometimes unsuccessful if you try to print an
image.
The image selected on the LCD monitor is not printed. (CP710 only)
When the list of images is printed, the index print contains an image displayed as “?”
instead of the image. (CP710 only)
You tried to print the
following images:
- An image taken with a
different camera or
recorded in a different type
- An image altered by a
computer
- An image data size that is
too big
- An image whose data is
corrupted
60
z Check the size of the image you are trying to print and the
number of recorded pixels on the camera, and convert the
image to JPEG compressed type that can be displayed on
the camera. Limit the size of image files to less than 8000
x 6000 pixels.
Error Messages
The power button of the printer lights or blinks red if any error occurs during printing. If a
problem occurs while the printer is connected to the camera, the camera’s LCD monitor
may display an error message.
On the CP710:
A screen indicating the error type is displayed also on the printer’s LCD monitor. See the
corresponding solution.
On the CP510:
Check the camera’s LCD monitor, and see the corresponding solution.
CP710’s
LCD Monitor
Camera’s LCD Monitor
No paper
z Check that the paper cassette is correctly installed.
z Make sure that the paper cassette contains paper.
z If paper is not feeding correctly, remove the paper cassette, and manually
remove any paper remaining in the printer.
Incompatible paper size
z Wrong paper size is loaded in the paper cassette. Use the designated
paper size.
Paper Jam
z Turn the power off and turn it on again. If the printer fails to eject the paper,
contact a Canon Customer Support help desk for assistance.
Paper has been changed
No Display
z Paper was changed after the print menu was displayed. Change back to
the original paper size or change the print settings.
No Ink
z Load an ink cassette if it is not in the printer.
z If the ink cassette is out of ink, load a new ink cassette.
Paper and ink do not match
z Check the ink/paper sets, and use the right ink/paper set.
Ink error or Ink cassette error
z Remove the ink cassette from the printer, take up the slack in the ink sheet,
and then reload the cassette. If this does not solve the problem, replace
with a new ink cassette. If the ink cassette is stuck in the printer, contact a
Canon Customer Support help desk for assistance.
61
CP710’s
LCD Monitor
Camera’s LCD Monitor
Recharge the printer battery
z Change it with a fully charged battery pack or recharge the battery pack.
You can also use the printer’s compact power adapter.
Communication error
z Turn the printer and camera power off and turn it on again. If the error
message does not clear, contact a Canon Customer Support help desk for
assistance.
Cannot print!
z You tried to print the following images:
-An image taken with a different camera or recorded in a different type
-An image altered by a computer
Check whether the image’s size matches the camera’s pixel capacity. If the
size is not appropriate, resize the image and convert it as necessary to a
JPEG image that the camera can display.
Could not print xx images
z You tried to print xx of the following images at the DPOF setting:
-An image taken with a different camera or recorded in a different type
-An image altered by a computer
Check whether the image’s size matches the camera’s pixel capacity. If the
size is not appropriate, resize the image and convert it as necessary to a
JPEG image that the camera can display.
File Error
z You tried to print an image that is not PictBridge compliant. Some images
that have been recorded with another camera or modified using a
computer cannot be printed. Convert the images as necessary to JPEG
images that the camera can display.
No Display
62
Hardware Error
z Check whether or not an error other than a paper or ink error has occurred.
Printing from Memory Card (CP710 only)
LCD monitor
Cause/Solution
z The memory card is not loaded in the card slot.
z The memory card is not properly loaded in the card slot. Insert the memory
card all the way into the card slot (p. 34).
z The memory card does not contain any images. Insert a memory card
recorded with images.
z You tried to print the following images. Pressing the PRINT/STOP button
returns to the original screen.
- An image recorded in a different camera or data type
- An image that has been loaded into a computer and edited
- An image data size is too big
- An image whose data is corrupted
Check the size of the image you are trying to print and the number of
recorded pixels on the camera, and convert the image to a JPEG image
that can be displayed on the camera. Limit the size of image files to less
than 8000 x 6000 pixels.
63
Specifications
„ Compact Photo Printer SELPHY CP710/CP510
All data is based on standard Canon testing criteria. Details are subject to change without
notice.
Print Method
Dye-sublimation thermal transfer (with overcoating)
Resolution
300 x 300 dpi
Gradation
256 gradations/color
Ink
Dedicated ink cassette (Y/M/C/overcoating)
Paper
L size, Postcard size, Credit card size (full-sized label and 8-label sticker),
Wide size (100 x 200 mm (4 x 8 in.))
Feeding System
Automatic feed from paper cassette
Paper-Eject
System
Automatic paper ejection on the paper cassette
Print Modes
Standard (1-screen) print (borderless or bordered), Multiple (8-screen) print
(when label sheets are used)
Print Sizes
Borderless
Bordered
L size
89.0 x 119.0 mm
(3.5 x 4.7 in.)
79.2 x 105.3 mm
(3.1 x 4.2 in.)
Postcard size
100.0 x 148.0 mm
(3.9 x 5.8 in.)
91.4 x 121.9 mm
(3.6 x 4.8 in.)
Credit card size
54.0 x 86.0 mm
(2.1 x 3.4 in.)
50.0 x 66.7 mm
(2.0 x 2.6 in.)
22.0 x 17.3 mm (0.9 x 0.7 in.) (1 sticker from sheet of
8-label stickers)
Wide size (100 x 200
mm(4 x 8 in.))*1
Printing Speeds
*1
*2
64
100.0 x 200.0 mm
(3.9 x 7.9 in.)
91.4 x 121.9 mm
(3.6 x 4.8 in.)
When a Canon camera Printing from memory card
is connected *2
(CP710 only)
L size print
Approx. 50 sec.
Approx. 73 sec.
Postcard size print
Approx. 58 sec.
Approx. 85 sec.
Credit card size print
Approx. 31 sec.
Approx. 44 sec.
Wide size (100 x 200
mm (4 x 8in.)) print
Approx. 74 sec.
Approx. 105 sec.
The printing area may vary depending on the camera used.
The above printing speeds are applicable when Canon compact digital camera equipped with the
DIGIC II is connected to the printer. Printing speeds may vary with other cameras. Based on
Canon's standard testing conditions. Variations may occur depending on printing.
Interface
Operating
Temperatures
Operating Humidity
Power Source
Power Consumption
Dimensions
Weight
Signal transfer
Connection
method
Proprietary protocol for Canon camera’s, PictBridge
Camera connection Retractable USB cable
Interface cable included with the camera
Computer connection Commercially available USB cable
Recommended printer cable
Material: AWG 28 or upper-grade
Type:Twisted-pair, sealed cable
(compatible with high-speed
mode) Length: max. 5.0 m (16.4 ft.)
Memory Card SD memory card, CompactFlash (CF) card, Microdrive,
(CP710)
Memory Stick, Memory Stick PRO, MultiMedia Card, Magic
Gate Memory Stick
Memory cards that require a specific adapter
miniSD card, xD-Picture Card, Memory Stick Duo, Memory
Stick PRO Duo, Magic Gate Memory Stick Duo
5 - 40°C (41 - 104°F)
20 - 80%
AC 100 - 240 V (50/60 Hz)
AC 60 W or less (4 W or less when idle)
178.0 x 131.0 x 63.0 mm (7.0 x 5.2 x 2.5 in.)
CP710: Approx. 980 g (34.6 oz.) (excluding ink and paper cassettes)
CP510: Approx. 940 g (33.2 oz.) (excluding ink and paper cassettes)
„ Compact Power Adapter CA-CP200
Input Voltage
Rated Output
Operating
Temperatures
Dimensions
Weight
AC 100 - 240 V (50/60 Hz)
1.5 A (100 V) - 0.75 A(240 V)
DC24 V, 2.2 A
0 - 45°C (32 - 113°F)
122.0 x 60.0 x 30.5 mm (4.8 x 2.4 x 1.2 in.) (excluding cable)
Approx. 310 g (10.9 oz.)
„ Battery Pack NB-CP2L (sold separately)
Type
Nominal Voltage
Nominal Capacity
Charge Cycles
Number of prints*
Operating
Temperatures
Dimensions
Weight
Lithium ion battery
DC 22.2 V
1200 mAh
Approx. 300
L size paper: Approx. 36 sheets
Postcard size paper: Approx. 36 sheets
Card size paper: Approx.72 sheets
Wide size (100 x 200 mm (4 x 8 in.)) paper: Approx. 24 sheets
5 - 40°C (41 - 104°F)
110.0 x 40.7 x 37.5 mm (4.3 x 1.6 x 1.5 in.)
Approx. 230 g (8.1 oz.)
*Test Conditions: Normal temperature (23°C/73°F), Canon images, continuous print
The above data may vary according to the printing environment and the image to be printed.
At low temperatures, the battery pack performance may diminish and the low battery icon may
appear very rapidly. In these cases, battery performance can be recovered by putting the
battery pack in you pocket, for example, to warm it up before use.
65
Printing with Non-Canon Digital Cameras
Since the CP710/CP510 printers support the direct print PictBridge* standard, you can
connect PictBridge compliant non-Canon digital cameras to easily print high image
quality photos.
*PictBridge: PictBridge is an industry standard for direct printing that allows you to print images
without using a computer by directly connecting a digital camera or digital camcorder
(hereafter “camera”) to a printer, regardless of their brands and models.
„ Before Using the Printer
Please read carefully the user guide that came with your camera and make sure that:
z The camera is PictBridge compliant.
z You are using the retractable USB cable or the USB cable for the camera/computer connection
to connect the printer to the camera. (This cable may be included with the camera.)
z The camera’s communication settings are configured correctly.*
z You set the print settings with the camera.*
*For details, refer to the camera’s user guide.
„ Connecting the Camera
Connect the retractable USB cable to the camera’s terminal. If the connector on the
camera side does not match up, insert one end of the USB cable included with your
camera in the printer’s direct print port (p. 20, 21) and insert the other end in the camera’s
terminal. (For details, refer to the camera’s user guide.)
z The printer’s power button blinks green several times once the printer and camera are correctly
connected. The power button lights steadily green once it is ready to print.
z If a problem occurs during a connection or during printing, the printer’s power button lights or
blinks red. If this happens, the error message that appears on the camera’s LCD monitor may
differ according to your camera model.
Printing speed may differ according to your camera model and the image’s number of
recorded pixels. (The value written on page 64 is a printing speed obtained when printing
with a Canon camera.)
66
Memo
67
Download PDF

advertising