Optimus N-8640DS ESTACION EMP.IP-65 PULS.LLAMADA AUDIO IP manual
TOA N-8640DS is an IP door station designed for indoor use. It features high-quality hands-free conversation and can be connected to a network of 10BASE-T/100BASE-TX. The N-8640DS has 1 control input and 5 control outputs, allowing connections to a sensor, electronic lock, and other external equipment. It is in full conformity with IP65 water-proof and dust-proof standards and has an operating temperature range of -10 to +50°C.
advertisement
INSTALLATION
MANUAL
IP DOOR STATION N-8640DS
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety.
• After reading, keep this manual handy for future reference.
CAUTION
Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage.
• Use the dedicated AC adapter or its equivalent for the unit.
Note that the use of other adapter may cause a fire.
2. GENERAL DESCRIPTION
Designed to connect to the IP network, the N-8640DS is an indoor use door station featuring high quality hands-free conversation. It is equipped with 1 control input and 5 control outputs, allowing connections to a sensor, electronic lock, and other external equipment. The N-8640DS can be mounted either flush in a wall or on a wall by using the designated mounting box.
The N-8640DS is in full conformity with IP65 water-proof and dust-proof standards. The operating temperature range is –10 to +50°C.
3. WALL MOUNTING
3.1. In-Wall Mounting
Mount the N-8640DS to the YC-150 or electrical box mounted in the wall.
Wall surface
Waterproof washer
(accessory)
YC-150 Back box (optional) or 3-gang electrical box
N-8640DS
Machine screw M4 x 20 (accessory)
Note
The wall should be over 12 mm thick, and the opening in the wall for an electrical box should be under 115 mm (wide) by
162 mm (high).
Accessory screws
The N-8640DS comes with 2 types of screws: machine screw M4 x 20 and UNC No.6 x 20.
For the electrical box provided with unified threads, use the oval head combination screws UNC No.6 x 20.
Notes
• When controlling an electronic lock with the N-8640DS unit, use "Torx" screws to attach the unit at installation so that it cannot be detached easily.
• When installing the unit outdoors or at locations where it gets wet with water, tightly seal the panel edges.
Besides, provide a weep hole at the underside of the mounting box to permit water to drain off.
• Be sure to ground both the YC-150 or electrical box, and the frame ground terminal on the unit's rear.
Seal the panel edges.
N-8640DS's front panel
3.2. On-Wall Mounting
Mount the N-8640DS to the YS-13A Wall-mount box mounted in the wall.
Wall surface
Rear plate
Waterproof washer
(accessory)
Machine screw
M4 x 20
(accessory)
N-8640DS
Install the YC-13A with its rear plate removed.
YS-13A
Make a weep hole (to allow water to exit) in the bottom.
Accessory screws
The N-8640DS comes with 2 types of screws: machine screw M4 x 20 and UNC No.6 x 20.
Use the M4 x 20 screw.
Notes
• When controlling an electronic lock with the N-8640DS unit, use "Torx" screws to attach the unit at installation so that it cannot be detached easily.
• When installing the unit outdoors or at locations where it gets wet with water, tightly seal the edges of the panel and those of the box's rear surface in contact with the wall surface. Besides, make a weep hole (to allow water to exit) in the YS-13A's bottom. (Refer to the figure shown below.)
• Be sure to ground the frame ground terminal on the unit's rear.
[YS-13A dimensional drawing]
Seal the panel edges and rear edges (on the wall side).
6-φ4.5
(for wall mounting)
4-M4
(for N-8640DS mounting)
YS-13A
Wall surface
92 46
83.5
115
55
4. WIRING
Frame ground
1
N-8640DS rear
LAN coupler (accessory)
To network
2
3
To AC mains
Control output 1 (brown)
Control output 2 (red)
Control output 3 (orange)
Control output 4 (yellow)
Control output COM (purple)
Control output (blue)
Control output (blue)
Control input HOT (gray)
Control input COM (white)
Speaker cable (black)
Speaker cable (black)
* Connection example
Control output (blue)
Control output (blue)
To an indicator or other external equipment
[Specifications]
Open collector output
Withstand voltage: 30 V DC
Max. control current: 50 mA
To an electronic lock or other external equipment*
[Specifications]
Relay contact output
Withstand voltage: 30 V DC
Max. control current: 500 mA
To a switch, sensor, or other external equipment
[Specifications]
No-voltage closed contact input.
Open voltage: 5 V DC
Short-circuit current: 10 mA
or less
To external speakers
(8 Ω, 0.6 W or more)
Diode
-
Relay
+
External power supply
24 V DC
GND
Can be connected to a network of 10BASE-T/100BASE-TX in auto-sensing.
Use a UTP category 5 or more straight through cable with an
RJ-45 connector for this connection.
Connect the AC adapter*.
Use the AD-1210P/1215P (optional) or equivalent.
As for the usable adapter, consult your TOA dealer.
The following 2 methods are available for supplying power to the station.
• From a DC 12 V AC adapter
• From an IEEE802.3af compliant PoE switching hub
(For connection, refer to the instruction manual supplied with the switching hub.)
Warning
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Traceability Information for Europe (EMC directive 2004/108/EC)
Manufacturer:
TOA Corporation
7-2-1, Minatojima Nakamachi, Chuo-ku, Kobe, Hyogo, Japan
Authorized representative:
TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg, Germany
URL: http://www.toa.jp/
133-06-302-40
advertisement
Key Features
- Indoor use
- High-quality hands-free conversation
- 1 control input and 5 control outputs
- IP65 water-proof and dust-proof
- Operating temperature range of -10 to +50°C
Frequently Answers and Questions
What are the dimensions of the N-8640DS?
What type of power supply does the N-8640DS use?
How many control inputs does the N-8640DS have?
How many control outputs does the N-8640DS have?
What is the maximum control current for the N-8640DS's control outputs?
What is the IP rating of the N-8640DS?
What is the operating temperature range of the N-8640DS?
Related manuals
advertisement