ag6007-e

ag6007-e
Absolute rotation encoder
AAG60007
360° degrees SSI
Digitronic Automationsanlagen GmbH
Steinbeisstraße 3 · D - 72636 Frickenhausen · Tel. +49 7022 40590-0 · Fax -10
Auf der Langwies 1 · D - 65510 Hünstetten-Wallbach · Tel. +49 6126 9453-0 · Fax -42
Internet: http://www.digitronic.com · E-Mail: [email protected]
2 rue René Laennec 51500 Taissy France
Fax: 03 26 85 19 08, Tel : 03 26 82 49 29
E-mail:[email protected]
Site web : www.hvssystem.com
Digitronic
Automationsanlagen GmbH
Absolute rotation encoder
AAG60007
Notification
This handbook corresponds with the unit version of 12/2006. The company Digitronic
Automationsanlagen GmbH reserves the right to implement changes that result in an improvement of
the quality and the functions of the device at any time and without any announcements.
This instructions manual was created with a maximum of care, but mistakes are not out of the
question. We are thankful for any comments, regarding possible mistakes in the instruction manual.
UP-date
You can also obtain this instruction manual on the Internet at http://www.digitronic.com in the latest
version as PDF file.
Qualified personal only
Commissioning and operation of the device may only be carried out by qualified personal. Qualified
personal are persons, authorized with commissioning, grounding and labeling devices, systems and
electrical circuits according to the applicable standards of security
Liability
(1) The salesperson is liable for any damages for which he or the rightful owner is responsible up to
the amount of the actual salesprice. Liability concerning missed profits, failed-to-appear savings,
indirect damages and consequential damage is excluded.
(2) The liability restrictions above are not valid concerning assured characteristics and damages, which
are caused by intention or coarse negligence.
Protection
The device AAG60007 and this instruction manual are protected by copyright. All rights are reserved.
Neither the device AAG60007, nor this document may be copied as a whole or partially, photocopied,
reproduced, translated or transferred to electronic media of any kind or into machine readable format
without prior written permission by the company Digitronic Automationsanlagen GmbH.
Note:
The products of Digitronic are so well constructed that they will not be effected by the
millenium.
Note:
This device fulfills the following norms according to electromagneticalcompatibility:
EN61000-6-1, EN61000-6-4 and EN61000-6-3.
(c) Copyright 1992 - 2006 / Datei: AG6007_E.DOC
Digitronic Automationsanlagen GmbH
Auf der Langwies 1
D-65510 Hünstetten - Wallbach
Tel. (+49)6126/9453-0 Fax. (+49)6126/9453-42
Internet: http://www.digitronic.com / E-Mail: [email protected]
Version from: 08.12.2006
Page: 2
2 rue René Laennec 51500 Taissy France
Fax: 03 26 85 19 08, Tel : 03 26 82 49 29
E-mail:[email protected]
Site web : www.hvssystem.com
Digitronic
Automationsanlagen GmbH
Absolute rotation encoder
AAG60007
1. The absolute rotation encoder AAG60007
Turns with a resolution of one angle degree can be measured by the absolute rotation encoder and
can be connected through the serial synchronized data exchange to the camswitchunits of the
CamCon series.
1.1. The dimensions of the AAG60007 rotation encoder
1.2. The SSI interface
The SSI interface is a common interface for absolute single and multiturn encoders. The CamCon
supplies the measuring system with 24Volt via this interface. To read the data, CamCon sends a clock
signal with an RS422 level to the encoder. The encoder the answers synchronously with the output
(data) of the position in Gray code. The frequency of the clock signal depends on the length of the
cable connecting ecoder and CamCon. This value can be configured at the CamCon.
Tp
Tmono
= clock impulse
maximum of 2MHz to a
minimum of 50kHz. (configured
at the cable length setting)
= mono flop time > 15µs
Version from: 08.12.2006
Page: 3
2 rue René Laennec 51500 Taissy France
Fax: 03 26 85 19 08, Tel : 03 26 82 49 29
E-mail:[email protected]
Site web : www.hvssystem.com
Digitronic
Automationsanlagen GmbH
Absolute rotation encoder
AAG60007
1.3. The terminal assignment of the AAG60007 rotation encoder
Connection cable
Type: AAG60007 / ST
binder series 623
soldering side
Attention: The order of the numbering of the connector plug
may differ from manufacturer to manufacturer. You
can only connect a plug with a different order, if you
keep the displayed attachment allocation in mind. The
location of the pins has to match the corresponding
functions at the device. This booklet uses a plug of
the Binder 623 series.
Attention: Connecting wrong poles of the connection cables can
damage or destroy the CamCon or the encoder.
The connection plug of the
SSI interface
is dependant of the type of the CamCon.
Consult the handbook
of your CamCon.
Connection plug
Type: AAG60007/ST
binder series 623
Encoder
Type: AAG60007
max. cable lenght: 300m
cable type: LIYCY 4x2x0.25 + 2x0.5 + shield
Please note:
Only use a sheathed pairwise connection cable. Do not put the cable near power
current wires. If possible, put the screening up at both sides.
order number: KKyy/S-XX meter
yy = CamCon typ for example 16,33,40,50,60,90,115,190,300 or 1756
XX = Length of the cable in meter
Version from: 08.12.2006
Page: 4
2 rue René Laennec 51500 Taissy France
Fax: 03 26 85 19 08, Tel : 03 26 82 49 29
E-mail:[email protected]
Site web : www.hvssystem.com
Digitronic
Automationsanlagen GmbH
Absolute rotation encoder
AAG60007
2. Installation and bringing into service
Rotation encoders are precision measuring units and therefore have to be handled as such. Please
regard the following installation instructions before bringing the rotation encoder into service.
-
-
When installing the rotation encoder, pay attention to the slight angular and radial misalignment.
(See technical data of the to be used couplings). Avoid blows towards the shaft and regard the
values concerning the shaft loads, which are listed on the data sheet.
Use flexible couplings ! The kind of couplings is determined by the speed, the torque, and the to be
by-passed angular and radial misalignment.
Connect the rotation encoder to the corresponding terminal assignment. See to it, that the operating
voltage recommended on the type plaquette is installed.
The plug should not be connected or disconnected when under voltage.
If the rotation encoder, even if correctly installed, does not function properly, intermittent faults can
be the cause of that. Such faults are due to power supply switchings, pulse mode controllers or
motors etc. Such faults can be reduced through proper protection facilities and through using
cables with a better shielding or an appropriate filtering network.
Should the occasion arise, protect the rotation encoder against environmental damage.
(solid particle impact, water spray ect.).
If any interventions are carried out by unauthorized personnel the factory guarantee becomes
invalidated !
Please review the wiring of the unit before switching it on and then engage the supply voltage of the
CamCon .
2.1. Technical data of the AAG60007 rotation encoder
Voltage supply.......................................................... 24VDC +-20%
Power consumption (without load) ........................... max. 20 mA
Resolution ................................................................ 360° degrees in steps from one degree
Data output............................................................... synchronos serial (SSI), capped graycode
Monofloptime............................................................ > 15µs
Cablelength between rotation encoder and
CamCon ................................................................... 300 meter max.
Mechanical characteristics
Valid torque .............................................................. maximum 5000 min-1
Inertia of the rotor..................................................... approx. 3x10-6 kgm2
Start-up torque ......................................................... <0.01 Nm
Shaft load ................................................................. axial 40 N / radial 80 N
Vibration solidness ................................................... >100m/s2, 10...2000 Hz
Acceleration solidness ............................................. >2500 m/s2, 6ms
Protection ................................................................. IP 65 / Case IP 67
Operating temperature............................................. -40°C..+90ºC
Weight...................................................................... about 350 g.
.
Version from: 08.12.2006
Page: 5
2 rue René Laennec 51500 Taissy France
Fax: 03 26 85 19 08, Tel : 03 26 82 49 29
E-mail:[email protected]
Site web : www.hvssystem.com
Digitronic
Automationsanlagen GmbH
Encoder acessoires
Shaft coupling / flange
3. The shaft couplings
Encoders are precision measuring units and therefore have to be kept apart from the vibrations and
tremors, as well as the from the misalignment of the machine. To part the encoder from these
influences use the flexible shaft couplings.
3.1. Wendel - shaft couplings type: WK/A/10-10
3.1.1. Technical data
Outer diameter .......................... 25 mm
Length ....................................... 32 mm
Clamp-screw ............................. M4
Nominal torsial moment ............ 120 Ncm
Acceptable radial shift ............... +/- 0.35 mm
Acceptable axial shift ................ +/- 0.5 mm
Acceptable angle-shift............... +/- 4 degree
Torsions strength ...................... 16 Nm/rad
Acceptable rotation speed......... 6000 U/min
Weight....................................... ca. 34g
2 rue René Laennec 51500 Taissy France
Fax: 03 26 85 19 08, Tel : 03 26 82 49 29
E-mail:[email protected]
Site web : www.hvssystem.com
Digitronic
Automationsanlagen GmbH
Encoder acessoires
Shaft coupling / flange
3.2. The shaft couplings WK/K/10-10
3.2.1. Technical data
Outer diameter .......................... 20mm
Length ....................................... 29,5mm
Clamp screw ............................. M 2,5
Standart torque ......................... 1,94 Nm
Valid radial shift......................... +/- 0,13 mm
Valid axial shift .......................... +/- 0,8 mm
Valid angular misalignment ....... +/- 1 Grad
Torsion stiffness........................ 31,5 Nm/rad
Valid torque ............................... 28000 min-1
Weight....................................... 20 g
2 rue René Laennec 51500 Taissy France
Fax: 03 26 85 19 08, Tel : 03 26 82 49 29
E-mail:[email protected]
Site web : www.hvssystem.com
Digitronic
Automationsanlagen GmbH
Encoder acessoires
Shaft coupling / flange
3.3. Isolting springdisks - shaft coupling type: WK/D/10-10
3.3.1. Technical data
Outer diameter .......................... 30 mm
Length ....................................... 22 mm
Clamp-screw ............................. M2.5
Nominal torsial moment ............ 40 Ncm
Acceptable radial shift ............... +/- 0.4 mm
Acceptable axial shift ................ +/- 0.4 mm
Acceptable angle-shift............... +/- 2.5 Grad
Torsions strength ...................... 90 Nm/rad
Acceptable rotation speed......... 12000 U/min
Weight....................................... ca. 23 g
2 rue René Laennec 51500 Taissy France
Fax: 03 26 85 19 08, Tel : 03 26 82 49 29
E-mail:[email protected]
Site web : www.hvssystem.com
Digitronic
Automationsanlagen GmbH
Encoder acessoires
Shaft coupling / flange
4. Clamping
.
4.1. Angle flange type: WF/AG
4.1.1. Technical data
Suitable for ............................................................... AAG60007, AAG612, AAG626, AAG66107,
AAG615 and ADG60 i.e. all turn-angle-encoder
with 48 mm partial circle, 36 mm flange and 10 mm
shaft.
Clamping of the turn-angle-encoder ........................ by three DIN 912 M4x12mm screws.
Weight...................................................................... approximately 180g.
2 rue René Laennec 51500 Taissy France
Fax: 03 26 85 19 08, Tel : 03 26 82 49 29
E-mail:[email protected]
Site web : www.hvssystem.com
Digitronic
Automationsanlagen GmbH
Encoder acessoires
Shaft coupling / flange
4.2. Bearing trestle: LAG60
4.2.1. Technical data
Suitable for ............................................................... AAG60007, AAG612, AAG626, AAG66107,
AAG615 and ADG60 i.e. all turn-angle-encoder
with 48 mm partial circle, 36 mm flange and 10 mm
shaft.
Acceptable rotation speed........................................ 3000 U/min.
Shaft drive ................................................................ 20mm with closed shaft notch.
Shaft drive ................................................................ 10mm to the turn-angle-encoder
with shaft coupling WK/K/10-10.
Bearing..................................................................... 2 pieces, maintenance free groove - ball bearings.
Clamping of the tiurn angle encoder ........................ by 3 DIN 912 M4x40mm screws.
Weight...................................................................... approximately. 1.5kg.
2 rue René Laennec 51500 Taissy France
Fax: 03 26 85 19 08, Tel : 03 26 82 49 29
E-mail:[email protected]
Site web : www.hvssystem.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement