WAFER-BT-i1 QIG V1.02_20141111
3.5” SBC with Intel® 22nm Atom™/Celeron® on-board SoC,
VGA/LVDS/iDP, Dual PCIe GbE, USB 3.0, PCIe Mini,
SATA 3Gb/s, mSATA, COM, Audio and RoHS
WAFER-BT-i1
Quick Installation Guide
Version 1.0
Nov 11, 2014.
Package List
WAFER-BT-i1 package includes the following items:

1 x WAFER-BT-i1 single board computer

1 x SATA with power cable kit (P/N: 32801-000201-100-RS)

1 x Audio cable (P/N: 32000-072100-RS)

1 x Power cable (P/N: 32100-087100-RS)

1 x QIG (Quick Installation Guide)

1 x Utility CD
©2006 Copyright by IEI Integration corp.
All rights reserved.
1
Specifications
 SoC:
Intel® Atom™ E3845 on-board SoC (1.91GHz, quad-core,
2MB cache, TDP=10W)
Intel® Atom™ E3827 on-board SoC (1.75GHz, dual-core, 1MB
cache, TDP=8W)
Intel® Atom™ E3826 on-board SoC (1.46GHz, dual-core, 1MB
cache, TDP=7W)
Intel® Atom™ E3825 on-board SoC (1.33GHz, dual-core, 1MB
cache, TDP=6W)
Intel® Atom™ E3815 on-board SoC (1.46GHz, single-core,
512KB cache, TDP=5W)
Intel® Celeron® J1900 on-board SoC (2GHz, quad-core, 2MB
cache, TDP=10W)
Intel® Celeron® N2930 on-board SoC (1.83GHz, quad-core,
2MB cache, TDP=7.5W)
Intel® Celeron® N2807 on-board SoC (1.58GHz, dual-core,
2MB cache, TDP=4.3W)
 BIOS: AMI UEFI BIOS
 Memory:
One 204-pin 1066/1333 MHz single-channel DDR3L
SO-DIMM supports up to 8GB (J1900, N2930, E3845, E3827,
E3826) or 4GB (N2807, E3825, E3815)
 Graphics Engine:
Intel® HD Graphics Gen 7 Engines with 4 execution unit,
supports DX11.1, OpenGL 4.2 and OpenCL1.2
 Display Output:
Dual Independent Display
1 x VGA (Resolution: [email protected])
1 x 24-bit dual-channel LVDS connector ([email protected])
1 x iDP interface for HDMI, LVDS, VGA, DVI, DP (up to
[email protected] Hz)
 Ethernet:
1 x PCIe GbE by Intel I210 controller (LAN1)
2
1 x PCIe GbE by Intel I211 controller (LAN2)
 Super IO: Fintek F81866
 Embedded Controller: ITE IT8528E
 I/O Interface:
1 x PS/2 KB/MS
2 x SATA 3Gb/s with 5V SATA power connector (no RAID)
1 x USB 3.0 (on rear I/O)
5 x USB 2.0 (1 on rear I/O, 4 by pin header)
1 x RS-422/485 (by pin header)
3 x RS-232 (1 on rear I/O, 2 by pin header)
 SMBus: 1 x 4-pin (1x4) wafer
 Audio:
Realtek ALC662 HD codec
1 x Analog audio by 10-pin (2x5) header
 Front Panel:
1 x 6-pin (1x6) wafer for power LED & HDD LED
1 x 2-pin (1x2) wafer for power button
1 x 2-pin (1x2) wafer for power reset
 LAN LED: 2 x 2-pin header for LAN1 Link LED, LAN2 Link LED
 Expansion:
1 x Full-size PCIe Mini card slot with mSATA support (SATA2
and mSATA share SATA signal)
 iRIS Remote Management Module: 1 x iRIS-1010 slot
 Digital I/O: 8-bit digital I/O (4-bit input, 4-bit output)
 FAN:
1 x 4-pin CPU fan connector
1 x 4-pin system fan connector
 Power supply:
12V DC input only (AT/ATX support)
 Watchdog Timer:
Software programmable support 1~255 sec. system reset
 Power Consumption:
3
[email protected] (Intel® Celeron® J1900 CPU, 1 x 8GB 1333
MHz DDR3 memory)
 Operating Temperature: -20°C ~ 60°C
 Storage Temperature: -30°C ~ 70°C
 Operation Humidity: 5% ~ 95%, non-condensing
 Dimensions: 146mm x 102mm
 Weight(GW/ NW): 600g / 250g
Ordering Information

WAFER-BT-i1-J19001-R10:
3.5” SBC supports Intel® 22nm quad-core Celeron® J1900 2.0 GHz
on-board SoC with VGA/LVDS/iDP, Dual PCIe GbE, USB 3.0, PCIe
Mini, SATA 3Gb/s, mSATA, COM, Audio, iRIS-1010 and RoHS

WAFER-BT-i1-N28071-R10:
3.5” SBC supports Intel® 22nm dual-core Celeron® N2807 1.58 GHz
(4.3W) on-board SoC with VGA/LVDS/iDP, Dual PCIe GbE, USB 3.0,
PCIe Mini, SATA 3Gb/s, mSATA, COM, Audio, iRIS-1010 and RoHS

WAFER-BT-i1-N29301-R10:
3.5” SBC supports Intel® 22nm quad-core Celeron® N2930 1.86GHz
(7.5W) on-board SoC with VGA/LVDS/iDP, Dual PCIe GbE, USB 3.0,
PCIe Mini, SATA 3Gb/s, mSATA, COM, Audio, iRIS-1010 and RoHS

WAFER-BT-i1-E38XX1-R10:
3.5” SBC supports Intel® 22nm Atom™ E38XX on-board SoC with
VGA/LVDS/iDP, Dual PCIe GbE, USB 3.0, PCIe Mini, SATA 3Gb/s,
mSATA, COM, Audio, iRIS-1010 and RoHS ( by order production,
MOQ: 100 )

32000-070301-RS: Dual-port USB cable

32205-003800-300-RS: RS-422/485 cable

32006-000300-100-RS: PS/2 KB/MS Y-cable without bracket
4
Jumpers setting and connectors
LABEL
FUNCTION
PWR_BTN1
Power On/Off button pin header
RST_BTN1
J_ATX_AT1
J_CMOS1
COM1, COM2, COM3
COM4
System Reset button pin header
AT/ATX mode select switch
Clear CMOS button
Serial port, RS-232
Serial port, RS-422/485
CN4
D-SUB
USB1, USB4
USB2
USB3
DIO1
JSPI1
JSPI2
CPU_FAN1
SYS_FAN1
LED_LAN1, LED_LAN2
KB_MS1
CN5
CN2
DP1
SATA_PWR1, SATA_PWR2
SATA1, SATA2
AUDIO1
INV1
LVDS_PWR1
LVDS1
SW1
J_FLASH1
Front Panel Pin Header
VGA connector
USB2.0 Port Pin Header
USB2.0 Port connector
USB3.0 Port connector
8 Bits Digital I/O Pin Header
BIOS SPI ROM Programming Pin
EC SPI ROM Programming Pin
CPU smart FAN connector
System smart FAN connector
LAN link LED connector
Keyboard & mouse pin header
+12V DC power input connector2
SMBUS connector
DP port internal pin header
SATA power connectors (5 V)
SATA 3Gb/s drive connectors
Audio pin header
LCD panel backlight power connector
LCD voltage selection
LVDS panel Connector
LVDS panel resolution selection
Flash Descriptor Security Override/ TXE
5
PWR_BTN1: Power On/Off button pinheader
PIN NO.
DESCRIPTION
Open
Normal Operation (Default)
Short
Power on/off
RST_BTN1: System Reset button pinheader
PIN NO.
DESCRIPTION
Open
Short
Normal Operation (Default)
Reset
J_ATX_AT1: AT/ATX mode select switch
PIN NO.
DESCRIPTION
Short A - B
ATX Mode (default)
Short B - C
AT Mode
J_CMOS1: Clear CMOS button
PIN NO.
Open
Push
COM1: (RS-232) Rear Port Define
PIN NO.
DESCRIPTION
1
2
3
4
5
NDCD1#
NRXD1
NTXD1
NDTR1#
GND
DESCRIPTION
Normal Operation (Default)
Clear CMOS Setup
PIN NO.
DESCRIPTION
6
7
8
9
NDSR1#
NRTS1#
NCTS1#
NRI1#
6
COM2: (RS-232) Pinheader
PIN NO.
DESCRIPTION
1
2
3
4
5
DESCRIPTION
6
7
8
9
10
NDSR2
NRTS2
NCTS2
NRI2
GND
PIN NO.
DESCRIPTION
6
7
8
9
10
NDSR3
NRTS3
NCTS3
NRI3
GND
NDCD2
NRXD2
NTXD2
NDTR2
GND
COM3: (RS-232) Pinheader
PIN NO.
DESCRIPTION
1
2
3
4
5
PIN NO.
NDCD3
NRXD3
NTXD3
NDTR3
GND
COM4: RS-422/485 serial port connector
PIN
DESCRIPTION
PIN
1
3
RXD485#
TXD485+
CN4: Front Panel Pin Header
PIN NO.
DESCRIPTION
1
3
5
+5V
PWR_LED+
HDD_LED+
DESCRIPTION
2
4
RXD485+
TXD485#
PIN NO.
DESCRIPTION
2
4
6
GND
PWR_LEDHDD_LED-
7
D-SUB: VGA connector
PIN NO.
DESCRIPTION
1
3
5
7
9
11
13
15
Red
Blue
GND
GND
VGAVCC
NC
HSYNC
DDCCLK
USB4: USB2.0 Port Pin Header
PIN NO.
DESCRIPTION
1
3
5
7
+5V
-DATA_USB1
+DATA_USB1
GND
USB1: USB2.0 Port Pin Header
PIN NO.
DESCRIPTION
1
3
5
7
+5V
-DATA_USB3
+DATA_USB3
GND
USB2: USB2.0 Port connector
PIN NO.
DESCRIPTION
1
3
+5V
-DATA_USB4
PIN NO.
DESCRIPTION
2
4
6
8
10
12
14
Green
NC
GND
GND
HOTPLUG
DDCDAT
VSYNC
PIN NO.
DESCRIPTION
2
4
6
8
GND
-DATA_USB2
+DATA_USB2
+5V
PIN NO.
DESCRIPTION
2
4
6
8
GND
-DATA_USB4
+DATA_USB4
+5V
PIN NO.
DESCRIPTION
2
4
-DATA_USB3
GND
8
USB3: USB3.0 Port connector
PIN NO.
DESCRIPTION
1
+5V
3
USB2P0+
5
USB3P0_RXDN1
7
GND
9
USB3P0_TXDP1
PIN NO.
2
4
6
8
DESCRIPTION
USB2P0GND
USB3P0_RXDP1
USB3P0_TXDN1
PIN NO.
2
4
6
8
10
DESCRIPTION
+5V
DGPO2
DGPO0
DGPI2
DGPI0
JSPI1: BIOS SPI ROM Programming Pin
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
DIO1: 8 Bits Digital I/O Pin Header
PIN NO.
DESCRIPTION
1
GND
3
DGPO3
5
DGPO1
7
DGPI3
9
DGPI1
1
3
5
+SPI_VCC
SPI_SO0_CN
SPI_SI0_CN
2
4
6
SPI_CS0#_CN
SPI_CLK0_CN
GND
JSPI2: EC SPI ROM Programming Pin
PIN NO.
DESCRIPTION
PIN NO.
1
+SPI_VCC_EC
2
3
SPI_SO0_CN_EC
4
5
SPI_SI0_CN_EC
6
DESCRIPTION
SPI_CS0#_CN_EC
SPI_CLK0_CN_EC
GND
CPU_FAN1: CPU smart FAN connector
PIN NO.
DESCRIPTION
PIN NO.
1
GND
2
3
FANIO1
4
DESCRIPTION
+12V
FANOUT1
9
SYS_FAN1: System smart FAN connector
PIN NO.
DESCRIPTION
PIN NO.
1
GND
2
3
FANIO2
4
DESCRIPTION
+12V
FANOUT2
LED_LAN: LAN1 link LED connector
PIN NO.
DESCRIPTION
PIN NO.
1
+3.3VLAN
2
DESCRIPTION
LAN1_LED_LINK#
LED_LAN2: LAN2 link LED connector
PIN NO.
DESCRIPTION
PIN NO.
1
+3.3VLAN
2
DESCRIPTION
LAN2_LED_LINK#
KB_MS1: Keyboard & mouse pin header
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
3
5
+5V_KBMS
MSCLK
KBCLK
2
4
6
CN5: +12V DC power input connector2
PIN NO.
DESCRIPTION
PIN NO.
1
GND
2
3
+12V
4
CN2: SMBUS connector
PIN NO.
DESCRIPTION
1
3
GND
SMBCLK
MSDATA
KBDATA
GND
DESCRIPTION
GND
+12V
PIN NO.
DESCRIPTION
2
4
SMBDATA
+5V
10
DP1: DP port internal pin header
PIN NO.
DESCRIPTION
1
3
5
7
9
+5V
DPD_OB_LANE1_P
DPD_OB_LANE3_N
GND
GND
DPD_AUX_CTRL_P
2
GND
DPD_OB_LANE2_N
DPD_OB_LANE0_P
+3.3V
11
13
15
17
19
PIN NO.
DESCRIPTION
2
4
6
8
10
DPD_OB_LANE1_N
GND
DPD_OB_LANE3_P
AUX_CTRL_DET_D
DDI1_HPD#
12
DPD_AUX_CTRL_N2
14
16
18
20
DPD_OB_LANE2_P
GND
DPD_OB_LANE0_N
NC
SATA_PWR1, SATA_PWR2: SATA Power Connectors
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+5V
2
GND
SATA1, SATA2: SATA 3Gb/s Drive Connectors
PIN NO.
DESCRIPTION
PIN NO.
1
3
5
7
GND
SATA_TXSATA_RX+
GND
AUDIO1:Audio pin header
PIN NO.
DESCRIPTION
1
3
5
7
9
LINE_OUTR
Analog_GND
LINE_OUTL
Analog_GND
LMIC1-R
2
4
6
DESCRIPTION
SATA_TX+
GND
SATA_RX-
PIN NO.
DESCRIPTION
2
4
6
8
10
LINEIN_R
Analog_GND
LINEIN_L
Analog_GND
LMIC1-L
11
INV1: LCD panel backlight power connector
PIN NO.
DESCRIPTION
PIN NO.
1
BL_PWM
2
3
+12V
4
5
BL_EN
J_LCD_PWR1: LCD voltage selection
PIN NO.
DESCRIPTION
Short A- B
Short B- C
LVDS1: LVDS panel Connector
PIN NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
GND
GND
LVDSA_DATA0
LVDSA_DATA0#
LVDSA_DATA1
LVDSA_DATA1#
LVDSA_DATA2
LVDSA_DATA2#
LVDSA_CLK
LVDSA_CLK#
LVDSA_DATA3
LVDSA_DATA3#
GND
GND
LVDSB_DATA0
DESCRIPTION
GND
GND
+3.3 V (Default)
+5 V
PIN NO.
DESCRIPTION
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
LVDSB_DATA0#
LVDSB_DATA1
LVDSBDATA1#
LVDSB_DATA2
LVDSB_DATA2#
LVDSB_CLK
LVDSB_CLK#
LVDSB_DATA3
LVDSB_DATA3#
GND
GND
+3.3V
+3.3V
+3.3V
+3.3V
12
SW1: LVDS panel resolution selection
* ON=0, OFF=1; Single=S, Dual=D
4-3-2-1
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
DESCRIPTION
800x600 18-bit Single (Default)
1024x768 18-bit Single
1024x768 24-bit Single
1280x768 18-bit Single
1280x800 18-bit Single
1280x960 18-bit Single
1280x1024 24-bit Dual
1366x768 18-bit Single
1366x768 24-bit Single
1440x960 24-bit Dual
1400x1050 24-bit Dual
1600x900 24-bit Dual
1680x1050 24-bit Dual
1600x1200 24-bit Dual
1920x1080 24-bit Dual
1920x1200 24-bit Dual
J_FLASH1: Flash Descriptor Security Overide/ TXE
PIN NO.
DESCRIPTION
Short 1-2
No override Mode (Default)
Short 2-3
Override Mode
13
Board Layout: Jumper and Connector Locations
(Unit: mm)
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement