CP-4FUSION 2
Revolabs Fusion™ Wireless
Microphone System
Set-Up Guide
Rev 1.12
Table of Contents
Contents of Box
4
Details About the Fusion
5
Fusion Front Panel
5
Fusion Back Panel
6
Fusion Set-Up
7
Audio-Conferencing
8
Video-conferencing Configuration
8
Pairing Microphones to Fusion Base Station
9
Configuring Fusion with Video-conferencing Sta- 11
Polycom Installation
12
Tandberg Installation
14
Lifesize Installation
15
Sony Installation
16
Programming Port DIP Switches
18
Multiple Fusion Systems
19
Tabletop Master Mute
20
Auto Phone Answer
21
Remote IR Sensor
22
Hearing Assistance
23
Indicator Lights
24
Safety and Regulatory Information
26
Specifications
30
Warranty
31
Part Numbers Covered in This Document:
8-Microphone System
01-8FUSION(EU)-NM (No microphones)
01-8FUSION(EU)-62 (6 omni tabletops/2 wearable)
4- Microphone System
01-4FUSION(EU)-NM (No microphones)
01-4FUSION(EU)-31 (3 omni tabletops/1 wearable)
Page 2
Revolabs Fusion™
Great audio, wireless mobility, and simple to install!
Simply plug the cable into the AV system or phone system and it
works. No software configuration is necessary. Even the Fusion box
is designed to be easy to use– vertically or horizontally. No
equipment rack needed. Just set the Fusion system on the credenza.
Video Conferencing
Revolabs Fusion Wireless Microphone Solution is compatible with all
of the major video-conferencing solutions, including Lifesize,
Polycom, Sony, and Tandberg. It includes a remote control to control
the sound volume. Decide on where you want to put the Fusion
system, whether you want to place it vertically or horizontally, plug in
the cables and you are ready to have great wireless audio in any
conference room.
Audio Conferencing
Plug the Fusion Wireless Microphone Solution into an analog
telephone jack and you are on your way to great wireless
teleconference calls. There is a remote control dialer to dial the
conference phone number. You may connect to powered speakers,
connect to existing speaker system or connect to a new room speaker
system to hear the call. Decide on where you want to put the Fusion
system, whether you want it vertical or horizontal, plug in the cables
and you are ready to have great wireless audio in any conference
room.
Flexible
The Fusion System supports any combination of Solo Wireless
Microphones- Wearable, Tabletop, or XLR adapter for a handheld
microphone. Choose the right microphone for your meeting
dynamics.
Rechargeable
Revolabs Wireless Microphones have a rechargeable battery that
provides eight hours of talk time after each full charge. Revolabs
Wireless Microphones recharge to 85% capacity in approximately 45
minutes.
Secure
All of Revolabs Wireless Microphones use 128-bit authentication, so
that no one can listen in.
Page 3
Set-Up Guide
Contents of box:
Fusion Base Station and four or eight wireless microphones (any type)
AC power adapter for Base StaCharger Base and
AC wall adapter for Charger Base
Remote Control
Fusion Base Station vertical stand
Cable A
Speakers
Cable B
Phone Cable
Cable C
RCA
Cable D
XLR
Optional boxes:
Four or eight wireless microphones, Remote IR Sensor, speakers
Page 4
Revolabs Fusion™
Details about the Fusion
Fusion Front Panel
The Revolabs Fusion Base Station, shown below in front and rear panel views,
manages wireless audio signal processing, and pairing between the Solo microphones
and the Fusion Base Station.
1.
2.
3.
4.
IR Remote receiver (if not in sight range of remote, page 22)
LED indicators: Displays microphone mute and pairing states
Pairing Push Buttons: For pairing microphones to Base Station
(page 9)
Power On LED/Volume indicator
Page 5
Set-Up Guide
Fusion Back Panel
1.
2.
Power
6 RCA Plugs
• AUX IN (for auxiliary input devices)
• AUX OUT
• RECORD OUT (for audio recording devices)
• ROOM OUT
• CONFERENCE IN
• CONFERENCE OUT
3. Conference Out XLR (Microphone level)
4. Network RJ 45 (Revolabs use only)
5. Telephone Line-in RJ11
6. Telephone Set-in RJ11
7. Audio Control RJ45 (Revolabs use only)
8. Programming Port: LEFT DIP Switches 1-8 (refer to page 18)
9. Programming Port: RIGHT DIP Switches 1-8 (Revolabs Use Only)
10. DB9 (Revolabs use only)
11. IR Remote DB9
Page 6
Revolabs Fusion™
STEP 1: Fusion Set-Up
Hardware
Decide if want to place Fusion Base Station horizontally or vertically on a flat surface. To setup vertically, place the Fusion Base Station vertical stand on the bottom of the Fusion unit.
Tighten bolt into Fusion Base Station.
Fusion Base Station Placement
WARNING: Do not put Fusion Base Station behind metal doors.
If you are putting the Fusion Base Station into a cabinet with non-metal doors, you need to use
the Remote IR Sensor (part number 07-IRREMO-01) for remote to work. (Refer to page 22)
Power
Plug AC power adapter power cord into the back of the Fusion Base Station and into wall
outlet.
Plug AC wall adapter into the power outlet and the other end into the microphone Charger
Base.
Place wireless microphones in the Charger Base, let charge overnight or at least eight hours.
Indicator lights on the Base Station Charger Base and microphones should be lit, verifying all
units are operating.
NOTE: Wait (approximately 30 seconds) until the Fusion Base Station has powered up and
the status lights have stopped flashing, before continuing on with next steps,
Page 7
Set-Up Guide
STEP 2: Audio Conferencing
Plug Cable A (single RCA to double RCA) single RCA connector into Fusion Base Station
<Room Out> RCA port, and then plug the double RCA connectors into the powered
speakers or a powered amplifier. Plug speakers into wall outlet.
Plug one end of Cable B, the phone line cable, into the Fusion Base Station <Line In>,
plug other end into phone jack. You may also plug a phone into the RJ11 <Set In>, You
may then dial with the remote control or the phone.
If you ordered 01-8FUSION(EU)-62 6 omni tabletops/2 wearable microphones or 014FUSION(EU)-31 3 omni tabletops/1 wearable microphone. You are all set to go! Take
out the Wireless Microphones, unmute them by pressing the mute button on the
microphone and the system is ready for a conference!
If you selected your microphones separately with the 01-8FUSION(EU)-NM or 014FUSION(EU)-NM Fusion part numbers, you must first establish a connection between
your microphones to the Fusion Base Station. This is called “pairing”. Refer to page 9.
STEP 2: Video Conferencing
You must have the audio output going from the Fusion Base station directly to the speakers
used by the video-conferencing station. Plug Cable A (single RCA to double RCA) single
RCA connector into Fusion Base Station <Room Out> RCA port and then plug the double
RCA connectors into the speakers or monitor.
Once you have configured your video-conferencing station as shown on pages 11-17, then:
If you ordered 01-8FUSION-62 6 omni tabletops/2 wearable microphones or 014FUSION-31 3 omni tabletops/1 wearable microphone. You are all set to go! Take out
the Wireless Microphones, unmute them by pressing the mute button on the microphone
and the system is ready for a conference!
If you selected your microphones separately with the 01-8FUSION-NM or 01-4FUSIONNM Fusion part numbers, you must first establish a connection between your microphones
to the Fusion Base Station. This is called “pairing”. Refer to page 9.
Page 8
Revolabs Fusion™
STEP 3: Pairing Microphones to Fusion Base Station if
Necessary
If you selected your microphones separately with the 01-8FUSION(EU)-NM or 01-4FUSION
(EU)-NM Fusion part numbers, you must first establish a connection between your
microphones to the Fusion Base Station. This is called “pairing”.
Pairing creates a link with a unique electronic serial number between the Solo wireless
microphone and the Fusion Base Station. When the microphone and Base Station have been
previously paired, the microphone will automatically try to connect to the Base Station
whenever it is lifted from the Charger Base.
Note: Microphones in new systems must be paired to the Base Station with each microphone
assigned to a unique channel on the base unit.
Remember, microphones are always muted (flashing RED LED light) when they are removed from the
Charger Base and the MUTE button needs to be pressed to make it “live” (flashing GREEN LED).
A microphone that is not paired will be indicated by either cycling RED-GREEN, or RED-YELLOWGREEN LED patterns. A Base Station LED that is not paired to a microphone will not show any activity
on the LED (make sure unit is first powered on by observing GREEN power LED on the front panel).
When the microphone and Fusion Base Station are paired, both microphone and channel LEDs will flash
RED as microphones are removed from the Charger Base and flash GREEN when un-muted.
To pair the microphone to the Fusion Base Station:
Turn the microphone OFF (no LED activity). If the microphone is ON, press and hold the
MUTE button for 10 seconds until the LED turns solid RED (do not release when you hear two
beeps). Release the button to turn the unit off.
(Continued on next page.)
Page 9
Set-Up Guide
STEP 3 Continued: Pairing Microphones to Fusion Base
Station if Necessary
Place the microphone unit into pairing mode by holding the MUTE button down for seven seconds. The LED will
turn solid RED. Release the MUTE button. The microphone is now in pairing mode.
Within one minute, push and hold the button for the desired channel on the Base Station (refer to page 5) for seven
seconds to enter into pairing mode then release. The LED for that channel will be solid red until pairing starts, as
indicated by a quick GREEN flash, then switching to flashing RED on both the microphone and the Base Station
(muted audio). Pairing is now complete.
The Fusion Base Station has four or eight indicator LED lights (one for each microphone) and pairing push buttons
on the front panel. When the LED is flashing GREEN or RED, that channel is active and connected to a wireless
microphone (GREEN is for live audio, RED is for muted). When the LED is OFF, the channel is inactive (the
microphone is out of range or turned off).
Page 10
Revolabs Fusion™
Configuring the Fusion with the Video Conferencing
System
The following pages have a representative sample of the most popular video-conferencing
systems. If you cannot find your specific video-conferencing station and need assistance in
configuring the cables, check the additional documentation in the FAQs or Technical
Documentation sections on www.revolabs.com , or the video-conferencing station
documentation.
Page 11
Set-Up Guide
Polycom® Installation (Polycom VSX7000 shown for example)
This information is meant to be illustrative only. Consult your Polycom Videoconferencing
System Administrator Manual for specific instructions.
1.
2.
Step 2
Step 1
Plug the red RCA connector on one end of Cable C into Polycom video-station <Audio Out
1>, and then plug the red RCA connector on the other end into the Fusion Base Station
<Conf In>.
Plug the black RCA connector on one end of Cable C into Polycom video-station <Audio
In>, and then plug the black RCA connector on the other end into the Fusion Base Station
<Conf Out>.
To configure the Polycom system:
Select the button from the main screen to access the System menu.
Select the System / Admin settings.
Enter the administrator password and press OK (if needed).
Select the Audio settings.
Confirm or modify the following settings:
• Midrange Speaker - OFF
• Line Input – Audio Mixer
• Echo Canceller - OFF
• Line Output – Monitor Far Site Audio
• Press OK to save changes.
Page 12
Revolabs Fusion™
Polycom® Installation (Polycom HDX9000 shown for example)
This information is meant to be illustrative only. Consult your Polycom Videoconferencing
System Administrator Manual for specific instructions.
NOTE: Requires 2 special RCA Male to 3.5mm 3 pin connectors Revolabs Part #07POLHDX-01.
Step 1
Step 2
1.
2.
Plug the 3.5mm 3 pin cable into the Polycom video-station <Audio In 1 Red>, and then plug
the RCA connector on the other end into the Fusion Base Station <Conf Out>.
Plug the 3.5mm 3 pin cable into the Polycom video-station <Audio Out 1 Red>, and then
plug the RCA connector on the other end into the Fusion Base Station <Conf In>.
To configure
the Polycom HDX 9000 Series system:
:
Select the button from the main screen to access the System menu.
Select the System / Admin settings.
Enter the administrator password and press OK (if needed).
Select the Audio settings.
Confirm or modify the following settings:
• Input Type – Line Input
• Input Type Level – 50%
• Echo Canceller - OFF
• Line Output Mode – Fixed
• Line Output Level – 50%
• Press OK to save changes.
Page 13
Set-Up Guide
Lifesize® Installation (Lifesize Team shown for example)
This information is meant to be illustrative only. Consult your Lifesize Videoconferencing System
Administrator Manual for specific instructions.
Step1
1.
2.
Step 2
Plug the red RCA connector on one end of Cable C into Lifesize video-station <Audio Out 1>,
and then plug the red RCA connector on the other end into the Fusion Base Station <Conf In>.
Plug the black RCA connector on one end of Cable C into Lifesize video-station <Audio In>,
and then plug the black RCA connector on the other end into the Fusion Base Station <Conf
Out>.
To configure the Lifesize system:
Select the button from the main screen to access the System menu.
Select the Administrator Preferences settings.
Enter the administrator password and press OK (if needed).
Select the Audio settings.
Confirm or modify the following settings:
• Voice Call Audio - Output
• Line Input - Enabled
• Line In to Line Out - Disabled
• Line In Acoustic Echo Canceller - Disabled
• Press OK to save changes.
Page 14
Revolabs Fusion™
Sony® Installation (Sony G70 shown for example)
This information is meant to be illustrative only. Consult your Sony Videoconferencing System Administrator
Manual for the specific instructions.
NOTE: Requires special adapter cable - XLR Female to 3.5 mm mini connector. Part number: 07-SONYVC-01
Step 1
1.
2.
Step 2
Plug the red RCA connector on one end of Cable C into Sony video-station <Audio Out 1>, and then plug the
red RCA connector on the other end into the Fusion Base Station <Conf In>.
Plug one XLR connector of Cable D, XLR to XLR, into XLR Female to 3.5mm adapter cable and then to the
Sony video-station <Mic 1 Input> and the other XLR connector into the Fusion Base Station Mic Level
Output <Conf Out (Mics)>.
To configure the Sony system:
• Select the Audio settings drop down menu.
Confirm or modify the following settings:
• Input Select - MIC
• MIC Select – MIC
• Echo Canceller - OFF
• CTE – OFF
• Press SAVE to save changes.
Page 15
Set-Up Guide
Tandberg™ Installation (Tandberg Edge 95 shown for example)
This information is meant to be illustrative only. Consult your Tandberg Videoconferencing
System Administrator Manual for the specific instructions.
Step 1
1.
2.
Step 2
Plug the black RCA connector on one end of Cable C into Tandberg video-station
<Audio Out 1>, and then plug the black RCA connector on the other end into the Fusion
Base Station <Conf In>. The other RCA connector is not used.
Plug one XLR connector of Cable D, XLR to XLR, into Tandberg video-station <Mic 1
Input> and the other XLR connector into the Fusion Base Station Mic Level Output
<Conf Out (Mics)>.
To configure the Tandberg system:
Select the button from the main screen to access the System menu.
Go to Audio settings
Confirm or modify the following settings:
• Input 1 - MIC
• Output 1 - ON
• Audio Leveling - OFF
• Echo Canceller - OFF
Adjust the audio Input Level if necessary.
Speak into the Revolabs microphones that are connected to the audio line inputs.
The audio meter should peak at about 5 dB.
Page 16
Revolabs Fusion™
Sony® Installation (Sony G70 shown for example)
This information is meant to be illustrative only. Consult your Sony Videoconferencing System Administrator
Manual for the specific instructions.
NOTE: Requires special adapter cable - XLR Female to 3.5 mm mini connector. Part number: 07-SONYVC-01
Step 1
1.
2.
Step 2
Plug the red RCA connector on one end of Cable C into Sony video-station <Audio Out 1>, and then plug the
red RCA connector on the other end into the Fusion Base Station <Conf In>.
Plug one XLR connector of Cable D, XLR to XLR, into XLR Female to 3.5mm adapter cable and then to the
Sony video-station <Mic 1 Input> and the other XLR connector into the Fusion Base Station Mic Level
Output <Conf Out (Mics)>.
To configure the Sony system:
• Select the Audio settings drop down menu.
Confirm or modify the following settings:
• Input Select - MIC
• MIC Select – MIC
• Echo Canceller - OFF
• CTE – OFF
• Press SAVE to save changes.
Page 15
Set-Up Guide
Tandberg™ Installation (Tandberg Edge 95 shown for example)
This information is meant to be illustrative only. Consult your Tandberg Videoconferencing
System Administrator Manual for the specific instructions.
Step 1
1.
2.
Step 2
Plug the black RCA connector on one end of Cable C into Tandberg video-station
<Audio Out 1>, and then plug the black RCA connector on the other end into the Fusion
Base Station <Conf In>. The other RCA connector is not used.
Plug one XLR connector of Cable D, XLR to XLR, into Tandberg video-station <Mic 1
Input> and the other XLR connector into the Fusion Base Station Mic Level Output
<Conf Out (Mics)>.
To configure the Tandberg system:
Select the button from the main screen to access the System menu.
Go to Audio settings
Confirm or modify the following settings:
• Input 1 - MIC
• Output 1 - ON
• Audio Leveling - OFF
• Echo Canceller - OFF
Adjust the audio Input Level if necessary.
Speak into the Revolabs microphones that are connected to the audio line inputs.
The audio meter should peak at about 5 dB.
Page 16
Revolabs Fusion™
Tandberg™ Installation (Tandberg Profile MXP shown for example)
This information is meant to be illustrative only. Consult your Tandberg Videoconferencing System
Administrator Manual for the specific instructions.
Step 1
Step 2
1. Plug one XLR connector of Cable D, XLR to XLR, into Tandberg video-station <Mic 1 Input> and the
other XLR connector into the Fusion Base Station Mic Level Output <XLR>.
2. Plug the black RCA connector on one end of Cable C into Tandberg video-station <Audio Out 1>, and
then plug the black RCA connector on the other end into the Fusion Base Station <Conf In>. The other RCA
connector is not used.
To configure the Tandberg system:
Select the button from the main screen to access the System menu.
Go to Audio settings
Confirm or modify the following settings:
• Input 1 - MIC
• Output 1 - ON
• Audio Leveling - OFF
• Echo Canceller and Noise Reduction (EC and NR) - OFF
Adjust the audio Input Level if necessary.
Speak into the Revolabs microphones that are connected to the audio line inputs.
The audio meter should peak at about 5 dB.
Page 17
Set-Up Guide
Programming Port: DIP Switches
The Fusion Base Station factory default settings are all OFF. The left Programming Port (#8, page 6) is end-user
configurable. Programming Port (#9, page 6) on the right is reserved for Revolabs Use Only.
NOTE: The Fusion system must be powered off and back on for any DIP Switch changes to take effect.
OFF
ON
1
2
3
4
5
6
7
Transmit Power Medium
Transmit Power Low
Frequency A Mode
Frequency B Mode
Tabletop Master Mute
Phone Auto Answer
IR Remote
Hearing Assistance
Page 18
8
Revolabs Fusion™
Multiple Fusion Systems
There are two settings that must be adjusted when more than one Fusion system is used within a 100’ (30.5 m)
range: frequency and transmit power level. These settings will enable several Fusion systems to be used near
each other, but not interfere with each other. Interference between systems can cause occasional audio noise
and signal dropouts on affected systems. Building conditions may influence this distance.
NOTE: Even using the settings below, the 8-Microphone Fusion System requires 40 feet (12.2 m)
between systems.
Setting the Transmit Power Level for Multiple Fusion Systems
In confined settings where multiple Fusion systems are used, or where audio interference is likely, it may be
necessary to reduce the transmit power levels. The transmit power level between the microphones and Fusion
Base Station can be set to the following three levels:
• Highest power level (default) – 100 feet (30.5 m) maximum operating distance between Microphone and
Fusion Base Station DIP Switches #1 and #2 are OFF (page 18).
• Medium power level – 30 feet (9 m) maximum operating distance between Microphone and Fusion Base
Station . DIP Switch #1 is ON and DIP Switch #2 is OFF (page 18).
• Lowest power level – 8 feet (2.4 m) maximum operating distance between Microphone and Fusion Base
Station . DIP Switch #2 is ON and DIP Switch #1 is OFF (page 18).
Frequency Settings
Frequency should be alternated to different frequency ranges, A and B. So an example of five conference rooms
in a row would be configured:
Conference
Room
1
2
3
4
5
Frequency
A B
A
B
A
To configure the Fusion to frequency mode A, Dip Switch #3 is ON and DIP Switch #4 is OFF. Frequency
mode B - Dip Switch #4 is ON and DIP Switch #3 is OFF. (page 18).
NOTE: The Fusion system must be powered off and back on for any DIP Switch changes to take
effect.
Page 19
Set-Up Guide
Tabletop Master Mute
Setting the Mute Option
Individual Muting (default)
In the default setting, each Solo microphone will mute only itself when its mute button on the microphone is pressed. To
mute all of the microphones, press the red MUTE button on the Remote Control; all microphones will flash red and no
individual microphone can be unmuted until the remote MUTE button is pressed again. All microphones will return to their
prior state. DIP switch #5 is OFF (page 18).
Tabletop Microphone Master Mute
In addition to the Remote Control MUTE button muting all of the microphones, the Solo Tabletop microphone MUTE button
will also act as a master mute and mute all active microphones. Pressing any Tabletop microphone MUTE button or the
Remote Control MUTE button will unmute all tabletop microphones. All wearable and handheld adapter microphones in use
will return to their prior state. DIP switch #5 is ON (page 18).
NOTE: The Fusion system must be powered off and back on for any DIP Switch changes to take effect.
Page 20
Revolabs Fusion™
Phone Auto Answer
Setting Phone Answering Mode
Answer with Remote Control (default)
To answer a phone call and begin a teleconference, the user must use the Remote Control and press the “Call” key. DIP
switch #6 is OFF (page 18).
Auto Answer
To answer a phone call and begin a teleconference, the user may use the Remote Control and press the “Call” key or the
Fusion Base Station will automatically answer the call after two rings. DIP switch #6 is ON (page 18).
NOTE: The Fusion system must be powered off and back on for any DIP Switch changes to take effect.
Page 21
Set-Up Guide
Remote IR Sensor
Setting the Remote IR Sensor Option
Front Panel IR Sensor (default)
If the Fusion Base Station is within view of the Remote Control, the front panel IR Sensor will accept all Remote Control
functions. DIP switch #7 is OFF (page 18).
Remote IR Sensor
If the Fusion Base Station is in a cabinet and behind a door (non-metal), the front panel IR Sensor cannot work. The Remote
IR Sensor cable (part number: 07-IRREMO-01) must be used to position the Fusion IR Sensor outside of the cabinet. Plug the
serial plug end into the IR Remote connector on the back panel of the Fusion Base Station (page 9), bring IR Sensor end out
of cabinet, and secure with Velcro. then set DIP switch #7 to ON (page 18).
NOTE: The Fusion system must be powered off and back on for any DIP Switch changes to take effect.
Page 22
Revolabs Fusion™
Hearing Assistance
Setting the Hearing Assistance Option
All Microphones Hear Audio From the Far End (default)
If an earpiece is plugged into any of the microphones, the user will hear the far end of the audio only. DIP switch #8 is OFF
(page 18).
Hear Audio From Both Far End and Within The Room
If the user needs to hear the audio from both the far end and the other microphones within the room, he/she must use the
microphone paired to Channel 8 (refer to pairing mode page 9) and the DIP switch #8 must be set to ON (page 18). Please
note that the Room Out RCA plug will no longer function in this mode; Aux Out will serve as Room Out.
NOTE: The Fusion system must be powered off and back on for any DIP Switch changes to take effect.
Page 23
Set-Up Guide
Revolabs Fusion™
Indicator Lights
Equipment Use
Microphone LED
Base Station
LEDs
Meaning
Microphone in
Charger Base
Solid RED
OFF
Charging in Progress
Solid GREEN
OFF
Charging Complete
OFF
OFF
Microphone powered OFF
or battery discharged
One RED flash
every 1.5 seconds
RED Flashing
Microphone master muted
by remote control or
tabletop master mute
Two RED flashes
every 1.5 seconds
RED Flashing
Microphone paired and
muted
GREEN flash
every 1.5 seconds
GREEN Flashing
Microphone paired and
“live”
Solid RED
Solid RED
Pairing mode or
confirmation of
powering-down
Alternating slow
GREEN and RED
OFF
or Alternating
slow
GREEN and RED
Microphone or channel
not paired
YELLOW flash alternating
with GREEN
GREEN Flashing
Microphone low battery
(mic live)
YELLOW flash alternating
with two RED flashes
RED Flashing
Microphone low battery
(mic muted)
Alternating RED, YELLOW,
GREEN, YELLOW
OFF
Searching for a
connection, or out of
radio range. The
Microphone will try to reestablish the link for
about 15 minutes, and
then turn off.
Rapid RED flashes continuing
for more than a few seconds
OFF
Radio congestion – it is
not possible to make a
radio connection because
there are already too
many nearby users, or
there is heavy radio
interference.
Groups of five rapid RED
flashes
OFF
Unit is faulty. Contact
your AV service provider
for advice.
Microphone not in
Charger Base
Set-Up Guide
Safety and Regulatory Information
Please read the following information to ensure safe use of your Revolabs system.
FCC User Information
FCC Registration Number: 0014898290
FCC ID: T5V-01-FUSION Revolabs Fusion™ Base Station 8 microphones
FCC ID: T5V-01-FUSION4 Revolabs Fusion™ Base Station 4 microphones
FCC ID: T5V-01-EXEMIC
Revolabs Solo™ Executive Microphone
FCC NOTICE TO USERS
Users are not permitted to make changes or modify the equipment in any way. Changes or modifications not expressly
approved by Revolabs, Inc. could void the user’s authority to operate the equipment. To meet FCC and Industry Canada RF
radiation exposure limits for general population (uncontrolled exposure), a minimum of 7.9 inches (20 cm) separation distance
must be maintained between the Fusion Base Station and users' and/or nearby persons' bodies at all times. Additionally, the
Fusion Base Station must not be co-located with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
This product has been found to comply with the Rules of 47 CFR Part 68 of the Federal Communications
Commission and Technical Requirements For Connection of Terminal Equipment to the Telephone Network TIA968-A-1, A-2 and A-3.
Certificate Number: US:6RMBR00BNEXIATC
Date: April 14, 2006
IMPORTANT NOTE: FEDERAL COMMUNICATIONS COMMISSION (FCC) RADIATION EXPOSURE
STATEMENT
This equipment complies with FCC radiation exposure limits for an uncontrolled environment.
Page 26
Revolabs Fusion™
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Page 27
Set-Up Guide
INDUSTRY CANADA NOTICE TO USERS
Operation is subject to the following two conditions:
(1) This device may not cause interference and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
IC: 6455A-01FUSION
IC; 6455A-01FUSION4
IC: 6455A-01EXEMIC
Revolabs Fusion™ Base Station 8 microphones
Revolabs Fusion™ Base Station 4 microphones
Revolabs Solo™ Executive Microphone
RESTRICTED USE WITH CERTAIN MEDICAL DEVICES
Hearing Aids
Some devices may interfere with some hearing aids. In the event of such interference, you may want to consult with your
hearing aid manufacturer to discuss alternatives.
Other Medical Devices
If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded
from RF energy. Your physician may be able to assist you in obtaining this information.
EXPORT LAW ASSURANCES
This product is controlled under the export regulations of the United States of America and Canada. The Governments of the
United States of America and Canada may restrict the exportation or re-exportation of this product to certain destinations.
For further information contact the U.S. Department of Commerce or the Canadian Department of Foreign Affairs and
International Trade. The use of wireless devices and their accessories may be prohibited or restricted in certain areas. Always
obey the laws and regulations on the use of these products.
01-FUSION-8CH-NA & 01-FUSION-4CH-NA North America UPCS Usage Restriction
Due to the UPCS frequencies used, this product is licensed for operation only in the United States of America and Canada.
01-FUSION-8CH-EU & 01-FUSION-4CH-EU European Union Usage Restriction
Due to the DECT frequencies used, this product is licensed for operation only in the European Union countries.
Page 28
Revolabs Fusion™
EUROPEAN COMPLIANCE
This equipment has been approved in accordance with Council Directive 1999/5/EC “Radio Equipment and
telecommunications Equipment.
Conformity of the Equipment with the guidelines below is attested by the CE mark.
Model Numbers:
01-8FUSIONEU-NM
Revolabs Fusion Base Station, European
01-4FUSIONEU-NM
Revolabs Fusion Base Station, European
01-8FUSIONEU-62
Revolabs Fusion System with 6 tabletop omni & 2 wearable mics, European
01-4FUSIONEU-31
Revolabs Fusion Base System with 3 tabletop omni & 1 wearable mics, European
03-EXEMICEU-BLK-11
Revolabs Solo™ Executive Microphone
03-EXECHGEU-STD-11
Revolabs Solo™ Executive
Charger
05-TBLMICEU-OM-BLK-11
Revolabs Solo™ Executive Table Microphone Omni
05-TBLMICEU-DR-BLK-11
Revolabs Solo™ Executive Table Microphone Cardioid
06-XLRMICEU-OM-BLK-11
Revolabs Solo™ Executive XLR Microphone Adapter
STANDARDS TO WHICH CONFORMITY IS DECLARED:
RF
ETSI EN 301 406 V 1.4.1 03/2001
EMC
ETSI EN 301 489-6 v1.2.1 (2002-04)
WEEE NOTIFICATION:
The Waste Electrical and Electronic Equipment (WEEE) directive (2002/96/EC) is intended to promote recycling of electrical
and electronic equipment and their components at end of life.
2003/11/EC & 2002/95/EC “ROHS COMPLIANCE DIRECTIVE”:
The products referenced herein are in compliance with the EU directive 2003/11/EC and EU directive 2002/95/EC.
SAFETY COMPLIANCE
TUV SUD AMERICA
Page 29
Set-Up Guide
Specifications
Dimensions, (L, W, H) and Weight:
Fusion Base Station
16.45 x 8.46 x 1.7”, 8.7 lbs
41.8 x 21.5 x 8.7 cm, 3.95 kg
Charger Base
8.3 x 4.3 x 1.0”, 1.0 lb 21.2 x 10.9 x 2.56 cm, 0.45 kg
Wireless Microphones Wearable: 0.9 x 0.8 x 2.6”, 0.05 lb
2.3 x 2.0 x 6.6 cm, 0.02 kg
Tabletop: 1.5 x 0.8 x 3.3”, 0.05 lb
3.8 x 2.0 x 8.4 cm, 0.02 kg
XLR Adapter: 0.9 x 0.8 x 4.0, 0.05 lb
2.3 x 2.9 x 102 cm, 0.02 kg
Radio Frequency:
01-8FUSION-XX
1.92 to 1.93 GHz (UPCS North America)
01-4FUSION-XX
1.92 to 1.93 GHz (UPCS North America)
01-8FUSIONEU-XX
1.88 to 1.90 GHz (DECT EU)
01-4FUSIONEU-XX
1.88 to 1.90 GHz (DECT EU)
Connectors:
Fusion Base Station
Charger Base
IR Remote Serial DB9
CD Programming Serial DB9 - for Revolabs use only
Audio Control RJ45 – for Revolabs use only
Telephone Line-In RJ11
Telephone Set-In RJ11
Network RJ45 – for Revolabs use only
Conference Out XLR male
Aux In RCA Plug
Aux Out RCA Plug
Record Out RCA Plug
Room Out RCA Plug
Conference In RCA Plug
Conference Out RCA Plug
DC power input port, Proprietary 4 pin microphone charge jacks
Power Requirements:
Fusion Base Station
100-240V AC, 50-60 Hz, 65W (power cable varies by country)
Charger Base
5V DC, 2 Amps (switching power supply varies by country)
Range:
100’ (30 meters) approx. (no obstructions)
Maximum Microphones:
01-8FUSION(EU)-XX, 8 channels maximum
01-4FUSION(EU)-XX, 4 channels maximum
Battery:
Lithium Polymer, 8 hours approx. talk time
Charge Time:
2 hours approx.
Audio Bandwidth
100-7000 Hz
Security:
128-bit DSAA (DECT Standard Authentication Algorithm) authentication
Page 30
Revolabs Fusion™
Warranty
Revolabs, Inc. warrants this product to be free of manufacturing defects. Repair or replacement of any defective part or unit
(at the discretion of the Seller) will be free of charge for the period of one year.
Any attempt by the user to alter the equipment, or equipment damaged by negligence, accident, or Acts of God voids this
warranty.
The Seller shall not be liable for any consequential damage resulting from the malfunction of this product. Should the user
experience unsatisfactory performance from this equipment, contact the Seller to obtain instructions for return, or
replacement, as deemed necessary.
This warranty is not transferable by the original end user.
Revolabs, Inc.
63 Great Road
Maynard, MA 01754
www.revolabs.com
800.326.1200
[email protected]
Page 31
Microphones must be fully charged and paired to the Fusion
Base Station prior to first use.
© 2008 REVOLABS, INC. All rights reserved. No part of this document may be reproduced in any form or by any means without express written permission from Revolabs, Inc. Product specifications are subject to change without notice.
Part #295034 REV 1.12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement