Starting Guide - Poseidon 1250 Tset

Starting Guide - Poseidon 1250 Tset
Poseidon 1250 Tset - Starting Guide
HW group
Poseidon 1250 Tset
Starting Guide - Poseidon 1250 Tset
First steps using Poseidon for temperature measuring
Poseidon 1250 Tset package contents:
• Poseidon 1250 device [600 006]
• Temp-1Wire temperature sensor with RJ12
connector [600 005]
• Door contact [600 119]
• 12 V power adaptor (EU: [600 080]
Note: US= [600 081], UK= [600 082],
• Printed „Quick setup“
• CD with documentation, full manual and
Software
1)
Poseidon 1250 Tset wiring
Check DIP switch configuration. See picture for DIP switch configuration during device setup
(DIP1=Off, DIP2=ON DIP3=Off, DIP4=Off).

Connect power adaptor to power supply and
to power supply connector of Poseidon.
Connect cables of door magnetic sensor to pin
1 and 2 of the Port 5 (Dry contacts).
Connect Temp-1Wire
temperature sensor
to the Port2 - RJ12
1-Wire sensor bus.
Connect Poseidon to Port1 - Ethernet (direct
cable to LAN Switch, crossed to PC).
• The green POWER indicator will light up
• If the Ethernet connection is OK, the green LINK indicator will also light up. It will blink during
data transfer via Ethernet (Activity indicator)
www.HW-group.com
Poseidon 1250 Tset - Starting Guide
HW group
2) IP address configuration - UDP Config
UDP Config start-up file is located in
root of supplied CD; latest version can
be found on our web: www.HWgroup.com, follow Poseidon 1250 link.
• Click the icon to run UDP Config
program – it will automatically search
for connected devices
In case the device was not connected to
network during UDP Config start-up, you
can easily click the Find Devices button to
repeat the search again.
The Program will search for devices on your
local network. The Poseidon identifies them
according to MAC address which is printed on
label located on bottom part of each device.
Double click on MAC address will open basic settings dialog window.
In this moment it is neccesary to setup network parameters.
Notice: In case you do not have following information, contact your
network administrator
• IP address
• HTTP Port
• Mask
• Gateway IP address
• Name of your device - optional
Do not forget to click Apply Changes button to safe new values to
Poseidon memory
Note: to setup IP address you can use as optional:
• Hercules (/Hercules.exe)
RS-232 serial port (any terminal, DIP1=ON, 9600 8N1
www.HW-group.com
Poseidon 1250 Tset - Starting Guide
HW group
3) Configuration and display of Poseidon via web browser
Enter IP address of the device to your web browser address bar or run UDP Config and click to the
IP address.
Configured device IP
address.
Status of Dry Contact
(Binary) Inputs.
List of connected
sensors, current
value, alarm status..
Graphic Flash Setup,
see following page..
Link to supplier or
tech. support (can be
changed, check the
manual).
SNMP MIB file, XML
description XSD file
and FirmWare
update over TCP.
www.HW-group.com
Poseidon 1250 Tset - Starting Guide
HW group
4) Configuration via Flash Setup
Click on Graphic Flash SETUP link on WWW page to open graphic version of setup which requires
installed Macromedia Flash player module in web browser. You can download latest version from
internet or you will find it on the supplied CD: \Poseidon\install_flash_player_7.msi
Autodetect Sensors:
If you are connecting new sensors, use sensor autodetect function in the
Flash setup – Sensors Setup tab.
Flash Setup allows you to:
• Configure names of sensors and their alarm values („Safe range“).
• Read current values of the sensors, values will reload in set period.
• Configure SNMP parameters (Community names & rights), define recipient to send SNMP
Traps and emails to.
• Configure name, password and safe range of IP address.
You can find detailed information in manual or on our website www.HW-group.com.
www.HW-group.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement