PVS 151

PVS 151
151
R
Package Vending
Specification
Page: 1 of 2
X
X
Date: 11 Aug 08
426 Industrial Boulevard • Kearneysville WV 25430-2776 • USA
Telephone: +1 304 728 7056 • Fax: +1 304 725 4016 • www.royalvendors.com
Revision: 00
PRODUCT NAME: 16 oz SoBe Lean bottle
BOTTLER / COMPANY: South Beach Beverage Co., Inc.
VOLUME: 16 oz. / 473 mL
PACKAGE TYPE: PET
HEIGHT: 7.95 in. / 201.8 mm
DIAMETER: 2.71 in. / 68.8 mm
WEIGHT: 1.15 lbs. / 0.52 kg
COUNTRY OF ORIGIN: USA
APPROVED VENDERS
VENDER
RETAINERS
79" CAPACITY
Front
Rear
Front
Rear
MIV Airflow*
8
N/A
28
N/A
MIV (regular)
9
N/A
28
N/A
TDV
8
12
30
60
RVV NG
N/A
N/A
8
N/A
* - Serial number 200422XX00001 and after.
KITS / PARTS: Merlin IV: FRONT COLUMNS: 332144 SoBe Lean Bottle Kit
M4 Front. TDV: FRONT COLUMNS: 296096 SoBe Lean Bottle Kit TDV Front. REAR
COLUMNS: None required. RVV NG: None required.
INSTALLATION INSTRUCTIONS
Note: Before working on vender, always remove power by unplugging the vender’s main power
cord from the AC voltage source (outlet).
MERLIN IV, FRONT COLUMNS:
NOTE: This package is not vendible in rear columns of the Merlin IV vender.
1. Install the filler plate (from the kit) by placing it all the way against the center divider channel, so that the filler plate’s top
tab slides into position 9 and the bottom tab slides securely into the square hole in the baffle nearest the divider. (See
Figure 1.) Install an anti-friction sheet so that the top of the sheet is at the laser line on the filler plate, with the bottom
portion of the sheet on the baffle. Apply a thin coat of silicone to the anti-friction sheet after it is installed.
2. Attach one retainer extrusion (from the kit) to each front-column product retainer. (See Figure 2.) Install the product
retainers in the positions shown in the list of Approved Venders, above.
3. Load bottles with caps to the front.
TDV:
1. FRONT COLUMNS: Attach one retainer extrusion (from the kit) to each front-column product retainer. (See Figure 2.)
Install the product retainers in position 8.
2. REAR COLUMNS: Pull out cap stops on center channel. Place rear-column product retainers in position 12.
3. Load bottles with caps to the front in front columns and butt-to-butt in rear columns.
X
X
RVV NG:
No special instructions.
ANY QUESTIONS? CONTACT ROYAL VENDORS’ CUSTOMER SERVICE DEPARTMENT
IN NORTH AMERICA, CALL TOLL FREE 1 800 931 9214
F0019085.FRM
ISSUE DATE: 29 JAN 2004
REV.: A
REV. DATE: 29 JAN 2004
151
R
Package Vending
Specification
Page: 2 of 2
X
X
Date: 11 Aug 08
426 Industrial Boulevard • Kearneysville WV 25430-2776 • USA
Telephone: +1 304 728 7056 • Fax: +1 304 725 4016
Revision: 00
PRODUCT NAME: 16 oz SoBe Lean bottle
Figure 1
Left-side column wall
Install in position 9
Tab hole
Filler plate
Anti-friction sheet
Install top of sheet at laser
line on filler plate, with bottom
portion of sheet on baffle.
Bottom tab
Install in tab hole
of baffle
Figure 2
Installing the
retainer extrusions
Retainer extrusion
Snaps onto each product retainer
Left product
retainer
Right
product
retainer
Left
product
retainer
Top view
ANY QUESTIONS? CONTACT ROYAL VENDORS’ CUSTOMER SERVICE DEPARTMENT
IN NORTH AMERICA, CALL TOLL FREE 1 800 931 9214
F0019085.FRM
ISSUE DATE: 29 JAN 2004
REV.: A
REV. DATE: 29 JAN 2004
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement