PRODUCT DATA Date: 11 July 2011 Information Sheet No.: TDS00448

PRODUCT DATA  Date: 11 July 2011 Information Sheet No.: TDS00448
PRODUCT DATA
Date: 11 July 2011
Information Sheet No.: TDS00448
EVO-STIK FOAM FILLER
A MOISTURE CURING POLYURETHANE
Evo-Stik Foam Filler is a fast curing assembly and filler foam. Evo-Stik Foam Filler is based on a one-part polyurethane
pre-polymer, which cures on contact with humidity and uses an environmentally safe propellant. Before using Evo-Stik
Foam Filler refer to the relevant Health & Safety Sheet.
Features
•
Exterior or interior use
•
Fills large or small gaps
•
Seals, fills, bonds, insulates
•
Cured foam can be cut, sanded, plastered or painted
Storage
Ensure that the product is stored
upright in a place were it cannot
be knocked over, accidentally
damaged or within the reach of
children or animals.
Cured foam
Once cured, the foam is medium
hard, predominantly closed cell
and heat and cold resistant.
Application temps
+10 C to +25 C, optimum 20 C.
Service temps
-40 to +80 C, for short periods up to
o
+100 C
Tack Free
8-10 minutes for a 20mm bead.
Uses
•
•
•
Evo-Stik Foam Filler is ideal for doorframe setting and
filling of gaps between brickwork and window frames.
Sealing draughty gaps around pipes which pass
through walls, cracks in walls as well as filling gaps in
roofing eaves, roof panel joints etc, where a tight
draught seal is required.
Evo-Stik Foam Filler adheres to the majority of common Cut-able
construction materials. Will not bond to polythene,
.
polypropylene and may damage polystyrene and other Load bearing
sensitive surfaces.
Coverage
Product Characteristics
Colour
Buff, yellows in sunlight
Physical form
Liquid aerosol
Specific Gravity
Cured foam is approximately
18g/litre, when allowed to foam
freely.
o
o
o
o
20 minutes for a 20mm bead.
12 hours for a 20mm bead.
300ml 11 – 13 litres
500ml 22.5 – 24.5 litres
750ml 36 – 39 litres
• All the above figures are approximate.
Composition
Product Code
Shelf life
Moisture curing polyurethane prepolymer in solution.
115446
132603
132610
300ml
500ml
750ml
12 months from the date of
manufacture when stored in dry
O
O
conditions between 5 C and 25 C.
• The coverage yields are the maximum expected if the
product is allowed to freely expand.
• These yields do not include wastage, which can be
considerable, depending upon the manner used.
Typical Performance Data (approx.)
2
Tensile Strength
18N/cm (DIN 53430)
Compressive
5N/cm at 20% stress (DIN 53421).
Thermal
Conductivity
0.04 W/MK
Fire Rating
B3, DIN 4102.
2
Bostik Limited, Common Road, Stafford, England., ST16 3EH. Tel: +44 (0)1785 272625 Fax: +44 (0)1785 272867
BOSTIK, EVO-STIK, CEMENTONE, SEALOCRETE, VALLANCE, LAYBOND, BISCEM & IDENDEN ARE REGISTERED TRADEMARKS OF BOSTIK LIMITED.
www.Bostik.co.uk
Page 1 of 3
PRODUCT DATA
Date: 11 July 2011
Information Sheet No.: TDS00448
Directions for use
Cleaning
IMPORTANT
1. Foam spillages must be removed whilst fresh with Gun
Foam Cleaner, acetone or nail varnish remover. First
cleaning may leave minute residues so repeat the
process.
Before using Evo-Stik Foam Filler refer to the relevant
Health & Safety Sheet. Available at www.bostik.co.uk
named as the code above.
2. Cured foam can only be removed mechanically.
Surface Preparation
Precautions in Use
1. The surfaces must be clean, free of loose particles and
free of dust and grease.
2. Just prior to foam application mist the surface well with
a water mist sprayer to ensure even curing of the foam.
Always store foam cans upright and in a position where
they cannot fall and are, yet, out of reach of children and
animals.
o
Do not expose containers to temperatures exceeding 50 c
3. Expansion is further helped by moistening each layer of
If transporting store upright in secure place in the boot of a
foam applied.
car not in the passenger compartment.
4. Always wear gloves and suitable clothing as cured
Never force the valve as damage can lead to foam leaking
foam is extremely difficult to remove.
unexpectedly. The valves are not ‘straight-through’ so they
5. Protect sensitive nearby surfaces from stray foam by
cannot be unblocked.
covering them. Remove all sources of ignition and
The product is so reactive with moisture that a can reisolate switches that might cause sparks.
sealed after opening, cannot be guaranteed usable later.
Application
1. Shake the can well before use.
2. Carefully screw the adapter and extension tube firmly
on to the valve. Do not over tighten taking care not to
operate the valve accidentally by exerting too much
downward or sideways pressure.
3. Always work in very well ventilated places.
4. Check there are no sources of ignition present.
O
Try to use the foam at 20 C. Below this the flow rate will be
slower and the yield much lower and the foam lower quality.
At higher temperatures the flow rate will be much faster and
the yield higher.
Never try to warm very cold cans quickly. Always place
O
them in a room at about 20 C for a few hours.
Be careful when using the product in windy conditions, as
the foam is so light it can be blown onto sensitive surfaces
where it will be very difficult to remove completely.
5. Foam flow can be regulated by applying different
pressure or by tilting the adapter with the valve pointing
downward.
6. The fresh foam will expand by approximately 150%,
during the curing process of reaction with moisture.
7. Apply foam in layers leaving a little space for some of
the expansion during curing. Damp each layer with a
water mist sprayer to assist rapid curing.
8. Foam spillages must be removed whilst fresh with Gun
Foam Cleaner, acetone or nail varnish remover. First
cleaning may leave minute residues so repeat the
process, even if not visible! Cured foam can only be
removed mechanically.
9. When cured the foam may be cut to give a neat finish.
The cured foam is not resistant to sunlight and should
be painted or covered for protection.
Bostik Limited, Common Road, Stafford, England., ST16 3EH. Tel: +44 (0)1785 272625 Fax: +44 (0)1785 272867
BOSTIK, EVO-STIK, CEMENTONE, SEALOCRETE, VALLANCE, LAYBOND, BISCEM & IDENDEN ARE REGISTERED TRADEMARKS OF BOSTIK LIMITED.
www.Bostik.co.uk
Page 2 of 3
PRODUCT DATA
Date: 11 July 2011
Sales & Technical contacts at Bostik
Sales
Technical advice
Technical Data & COSHH (MSDS) sheets
Information Sheet No.: TDS00448
Telephone
0844 371 1192
0844 371 1197
01785 272625
Facsimile
01785 241818
01785 272867
01785 212962
Email addresses
[email protected]
[email protected]
[email protected]
This disclaimer is issued by Bostik Limited ("the Company") and applies to the use of any products supplied by the
Company ("the Products") displayed on this Technical Data Sheet (“TDS”). Please read this disclaimer carefully before
using any of the Products. Using this TDS and/or the Product constitutes your acceptance of this disclaimer. Its contents
shall prevail over any directions of use and any disclaimer and/or exclusion or limitation of liability of the Company which
may appear on the packaging of the Products.
This disclaimer sets out the entire financial liability of the Company (including any liability for the acts or omissions of its
employees, agents and sub-contractors) to any user of the Products ("Product User") in respect of any use made or
resale by the Product User, of any of the Products in this TDS.
This disclaimer does not affect the Company's liability for death or personal injury arising from the Company's negligence
in respect of the Products, nor its liability for fraud, or fraudulent misrepresentation, nor any other liability which cannot
be excluded or limited under applicable law.
The Company's total liability however arising and whether caused
by tort (including negligence and breach of statutory duty), breach of contract or otherwise, arising in connection with
the use made or resale by the Product User of any of the Products in this TDS shall be limited to the price paid for the
Product by the Product User.
The Company shall not be liable to the Product User for any pure economic loss, loss of profit, loss of business,
depletion of goodwill or otherwise, in each case whether direct, indirect or consequential, or any claims (including in
respect of personal injury insofar as not caused by the Company's negligence) for consequential compensation
whatsoever (howsoever caused) which arise out of or in connection with the use made or resale by the Product User of
any of the Products in this TDS.
The Company shall not be liable to the Product User in relation
to any loss for any use which is inappropriate or use which is otherwise than in accordance with the relevant
instructions for use of the Products in this TDS or on the Product. Product Users are advised to confirm the suitability of
the Products by their own tests.
This TDS covers just one of a large range of products supplied by the Company.
Full information on these products and advice on application is freely available from our fully trained staff throughout the
country. In addition, specialist technical advice is available from our Technical Services Department. This TDS
supersedes all previous TDSs relating to the Products, and users of it must ensure that it is the current issue. Destroy all
previous TDS, and if in any doubt, contact the Company, quoting the code number in the top right hand corner on the
front of this document.
Bostik Limited, Common Road, Stafford, England., ST16 3EH. Tel: +44 (0)1785 272625 Fax: +44 (0)1785 272867
BOSTIK, EVO-STIK, CEMENTONE, SEALOCRETE, VALLANCE, LAYBOND, BISCEM & IDENDEN ARE REGISTERED TRADEMARKS OF BOSTIK LIMITED.
www.Bostik.co.uk
Page 3 of 3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement