SFP-10G-XXAC SFP+ Direct Attach Active Copper Cables 7m, 10m, 12m Reach Features

SFP-10G-XXAC SFP+ Direct Attach Active Copper Cables 7m, 10m, 12m Reach Features
SFP-10G-XXAC
SFP+ Direct Attach Active Copper Cables 7m, 10m, 12m Reach
Features

Support for multi-gigabit data rates up to
10.5Gbps

Data rates backward compatible to 1Gbps

Hot-pluggable SFP 20PIN footprint

I/O Connector designed for high speed
differential signal applications

Improved Pluggable Form Factor(IPF) compliant
for enhanced EMI/EMC performance

Low Power Consumption < 0.5W

Power Supply :+3.3V

Compatible to SFP+ MSA

Temperature Range: 0~ 70 °C

RoHS Compatible
Applications

High capacity I/O in Storage Area Networks, Network Attached Storage, and Storage Servers

Switched fabric I/O such as ultra high bandwidth switches and routers

Data center cabling infrastructure

High density connections between networking equipment
Product Description
The SFP+ active cable assemblies are high performance, cost effective I/O solutions for 10Gb Ethernet
and 10G Fiber Channel applications. SFP+ copper modules allow hardware manufactures to achieve
high port density, configurability and utilization at a very low cast and reduced power budget. The high
speed cable assemblies meet and exceed Gigabit Ethernet and Fiber Channel industry standard
requirements for performance and reliability.
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 US
Page 1 of 3
Rev.1.2 Oct 13/2012
Recommended Operating Conditions
Parameter
Symbol
Min
Max
Unit
-40
+85
°C
Tc
0
+70
°C
VCC3
3.14
3.47
V
0.5
W
Storage Ambient Temperature
Operating Case Temperature
Power Supply Voltage
Power Dissipation
Typical
3.3
PD
Systems
Performance
Media
Operating parameters
Hot-pluggable, industry-standard Small
10.5Gbps line speed, full duplex
Form-Factor
Supply voltage: 3.3V
Bit error rate: better than 10E-12
Pluggable(SFP+) copper cable,
Power consumption(per end): max 0.5W
available max 10m
Pin Descriptions
Pin
Logic
1
Symbol
Name/Description
VeeT
Transmitter Ground
2
LV-TTL-O
TX_Fault
N/A
3
LV-TTL-I
TX_DIS
Transmitter Disable
4
LV-TTL-I/O
SDA
Tow Wire Serial Data
5
LV-TTL-I
SCL
Tow Wire Serial Clock
MOD_DEF0
Module present, connect to VeeT
6
7
LV-TTL-I
RS0
N/A
8
LV-TTL-O
LOS
LOS of Signal
9
LV-TTL-I
RS1
N/A
10
VeeR
Reciever Ground
11
VeeR
Reciever Ground
12
CML-O
RD-
Reciever Data Inverted
13
CML-O
RD+
Reciever Data Non-Inverted
14
VeeR
Reciever Ground
15
VccR
Reciever Supply 3.3V
16
VccT
Transmitter Supply 3.3V
17
VeeT
Transmitter Ground
18
CML-I
TD+
Transmitter Data Non-Inverted
19
CML_I
TD-
Transmitter Data Inverted
VeeT
Transmitter Ground
20
Notes
1
1
1
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 US
Page 2 of 3
Rev.1.2 Oct 13/2012
1. Signals not supported in SFP+ Copper pulled-down to VeeT with 30K ohms resistor
Mechanical Dimensions
Ordering information
Part Number
Product Description
SFP-10G-07AC
SFP+ Direct Attach Active Cable(10GSFP+Cu), 7m, AWG:24,
0ºC ~ +70ºC
SFP-10G-10AC
SFP+ Direct Attach Active Cable(10GSFP+Cu), 10m, AWG:24, 0ºC ~ +70ºC
SFP-10G-12AC
SFP+ Direct Attach Active Cable(10GSFP+Cu), 12m, AWG:24, 0ºC ~ +70ºC
E-mail: sales@robofiber.com
Robofiber, Inc., 2491 Estand Way, Pleasant Hill, CA 94523 US
Page 3 of 3
Rev.1.2 Oct 13/2012
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising