Kambrook - Australia
Building 2, Port Air Industrial Estate
1A Hale Street
Botany NSW 2019
Australia
Customer Service Line 1300 139 798
Customer Service Fax 1800 621 337
www.kambrook.com.au
Kambrook - New Zealand
Private Bag 94411
Botany, Manukau
Auckland 2163
New Zealand
Customer Service Line/
Spare Parts 0800 273 845
Customer Service Fax 0800 288 513
www.kambrook.co.nz
Due to continual improvement in design or otherwise, the product you purchase may differ slightly from the illustration in this book. Issue D14
CaptivG3
Cyclonic
Bagless Vacuum
ALL MODELS KBV420/450/480
Instruction Booklet
Important
Please retain your instruction book for future use.
In the event that you need some assistance with your
Kambrook appliance, please contact our Customer Service
Department on 1300 139 798 (Australia) or 0800 273 845
(New Zealand). Alternatively, visit us on our website at www.kambrook.com.au or www.kambrook.co.nz
Contents
Kambrook Recommends
Safety First
Your CaptivG3 Cyclonic
Bagless Vacuum p4 p6
Operating Instructions
Care and Maintenance p7 p10
Troubleshooting p15
Kambrook Recommends Safety First
IMPORTANT: Please retain your instruction book for future use.
At Kambrook, we believe that safe performance is the first priority in any consumer product, so that you, our valued customer can confidently use and trust our products. We ask that any electrical appliance that you use be operated in a sensible fashion with due care and attention placed on the following important operating instructions.
Important Safeguards For Your Kambrook
CaptivG3 Cyclonic Bagless Vacuum
• Carefully read all instructions before operating the Kambrook CaptivG3 Cyclonic Bagless
Vacuum for the first time and save for future reference.
• Remove and safely discard any packaging material and promotional labels before using the vacuum for the first time.
• To eliminate a choking hazard for young children, remove and safely discard the protective cover fitted to the power plug of this appliance.
• To protect against electric shock, do not immerse the vacuum, cord or plug in water or any other liquid.
• Ensure that the power source to be used is the same as the voltage requirements of the product.
• Always switch vacuum cleaner to off, then switch off at the power outlet, and then unplug the vacuum cleaner when not in use and prior to cleaning the dust container or filters.
• Always ensure the vacuum cleaner is properly assembled before use. Follow the instructions provided in this book.
• Never use the vacuum cleaner without a dust container and motor protection filter in place.
• Never pick up anything that is burning or smoking such as cigarettes, matches or hot ashes.
• Avoid picking up hard, sharp objects with the vacuum as they may damage the canister, filter or motor.
• Do not use the vacuum to pick up flammable or poisonous liquids such as petrol, copier toner or other volatile substances. Do not use vacuum to pick up acids, asbestos or asbestos dust.
• Never use in the presence of explosive liquids or vapours.
• Do not leave the vacuum cleaner unattended when in use. Young children should be supervised to ensure that they do not play with the vacuum cleaner.
• Close supervision is required at all times when operating the vacuum cleaner near children.
• This vacuum cleaner is suitable for domestic use only. Do not use this vacuum cleaner for anything other than its intended use.
• Do not use or store outdoors.
• Fully extend the cord (to the yellow tape mark) whenever the vacuum cleaner is in use.
Please ensure that the cord is not extend past the red tape mark.
• Regularly inspect the supply cord, plug and actual vacuum cleaner for any damage. If damage is found in any way, immediately cease use of the vacuum cleaner and return to your nearest authorised Kambrook service centre for examination, replacement or repair
• Do not unplug the power plug by pulling on the cord.
• Hold the plug end when retracting the cord to prevent it from striking you or the vacuum.
• Do not use chemicals, steel wool, metal scouring pad or abrasive cleaners to clean the outside of the vacuum cleaner housing as these can damaged the housing
4
• To avoid an electrical overload, it is recommended that no other appliances are plugged into the same circuit as your vacuum cleaner when it is in use.
• Dirty and clogged filters may result in reduced suction performance. It is recommended that filters are cleaned after every use and replaced regularly to ensure maximum efficiency from your vacuum cleaner. If filters are left unclean it may results in reduction of suction power.
• Clean the floor tools regularly. Remove hair, cotton and the likes from the turbo brush head (for models KBV450 and KBV480 only) by cutting across the hair, cotton and the likes and by gently pulling it free.
• Keep the vacuum cleaner clean. Follow the cleaning instructions provided in this book..
Important Safeguards For All
Electrical Appliances
• Carefully read all instructions before operating the appliance and save for future reference.
• Remove and safely discard all packaging material and promotional labels before using the appliance for the first time.
• Fully unwind the power cord before use.
• Do not let the power cord hang over the edge of a bench or table, touch hot surfaces or become knotted.
• To protect against electric shock, do not immerse the power cord, power plug or appliance in water or any other liquid, unless it is recommended in the cleaning instructions.
• The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance, by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• It is recommended to inspect the appliance regularly. Do not use the appliance if the power supply cord, plug, connector or appliance becomes damaged in anyway.
Return the entire appliance to the nearest authorised Kambrook Service Centre for examination and/or repair.
• Any maintenance other than cleaning should be performed at an authorised Kambrook
Service Centre.
• This appliance is for household use only.
Do not use this appliance for other than its intended use. Do not use in moving vehicles or boats.
Do not use outdoors.
Misuse may cause injury.
• The installation of a residual current device
(safety switch) is recommended to provide additional safety protection when using electrical appliances. It is advisable that a safety switch with a rated residual operating current not exceeding 30mA be installed in the electrical circuit supplying the appliance.
See your electrician for professional advice
• Always turn the appliance to the OFF position, switch off at the power outlet and unplug at the power outlet when the appliance is not in use.
• Before cleaning, always turn the appliance to the OFF position, switch off at the power outlet, unplug at the power outlet and remove the power cord, if detachable, from the appliance and allow all parts to cool.
• Do not place this appliance on or near a heat source, such as hot plate, oven or heaters.
• Position the appliance at a minimum distance of 20cm away from walls, curtains and other heat or steam sensitive materials and provide adequate space above and on all sides for air circulation.
5
Your CaptivG3 Cyclonic
Bagless Vacuum
1.
Bagless convenience for easy removal of dirt and dust with no need for replacement bags
2.
Variable power control
3.
2000 watt motor for superior suction, fast and effective cleaning
4.
Dust level indicator
5.
Quality multi-terrain floor tool ideal for carpet and hard floors
6.
CaptivG3 turbo floor brush, picks up pet hair from carpet making it ideal for homes with pets (KBV450 and KBV480 models only)
7.
Hard floor tool for improved pick up on hard floors (KBV480 only)
8.
Telescopic chrome steel wand is easily extendable or retractable for varying height requirements
9.
Cyclonic cone helps separate particles from the air before filtering begins
10.
Two washable HEPA filters included
11.
Auto cord rewind
12.
Convenient carry handle
13.
Cord length 5m
14.
Performance indicator light
15.
Small brush
16.
Upholstery tool
17.
Crevice tool
KBV420 depicted
6
Operating Instructions
Before First Use
Remove any promotional material from the vacuum cleaner.
When unpacking the vacuum cleaner check to see you have received all the required components, such as the hose and other accessories before discarding the packaging.
To Operate the
Vacuum Cleaner
Locate the crush proof hose and push the connection point into the hose inlet connection on the front side of the vacuum, until a “click” sound is heard.
Connect the wide end of the metal wand to the hose end, and push together firmly.
Fig. 1
Fit the multi-terrain floor tool to the narrow end of the wand and push together firmly.
Fully extend the power cord by pulling the power plug out from the rear of the vacuum, until the yellow tape on the cord is showing.
NOTE: Ensure that you do not over extend the power cord
– do not extend past the red warning tape on the cord.
Plug into a 230V or 240V power point and switch the power on at the power point.
To commence vacuuming, push down on the on/off button cord on the top of the vacuum cleaner.
When vacuuming is complete, push press up switch off. Turn the power off at the outlet and then remove the power cord from the power outlet. When removing the plug from the power outlet, grasp the plug not the cord.
To retract the cord, firmly push down on the ‘cord rewind’ button on top of the vacuum cleaner.
down down press
IMPORTANT: Hold the plug end and guide the cord into the vacuum during retraction to prevent it from striking you or the vacuum.
Fig. 2
CAUTION: Always ensure that the dust container and the motor protection filter are correctly fitted.
Never operate without the dust container or filters in place.
7
Operating Instructions
continued
NOTE: The performance indicator light is a pressure sensitive device to warn that the vacuum cleaner is full of dust or something is blocking the suction. If the light turns on, check and remove any blockages or follow instructions in the section “Cleaning and replacing filters”.
Crevice and Brush
Tool Accessories
Variable Power Control
The power booster lever on the vacuum can be used for variable power control. Slide the lever toward the MAX marking for vacuuming hard floor and carpet surfaces. Slide the lever toward the MIN marking when using the crevice, upholstery and brush tools.
Fig. 4
The crevice tool is ideal for vacuuming hard to reach places such as the edges along skirting boards.
The brush and upholstery tools can be used to vacuum delicate surfaces and areas such as shelves and venetian blinds.
Set the variable speed control between minimum and medium power when using the tool accessories.
Fig. 3
Fig. 5
Turn off the vacuum cleaner when changing any attachments.
8
CaptivG3 Turbo Floor Brush
(KBV450 and KBV480 only)
Fig. 6
The CaptivG3 turbo floor brush is ideal for picking up dirt and hair, brushing them back into the nozzle.
It is great for cleaning carpets and homes with pets.
Hard Floor Tool
(KBV480 Only)
Fig. 7
The hard floor tool is ideal for vacuuming hard floors, with improved pick-up.
Simply fit the hard floor tool to the narrow end of the wand and push together firmly.
9
Care and Maintenance
Check all filters and replace them regularly. It is recommended to clean the filters after every use. For normal household vacuuming the filters should be replaced at least twice a year.
If you encounter reduced vacuum cleaner performance, check:
• Dust capacity in dust container
• All filters, including dust, motor and exhaust. Any clogging in the filters will reduce the efficiency of your vacuum cleaner
To clean the outside of the unit, wipe the exterior with a soft, damp cloth.
Never use an abrasive cleaner.
Emptying the Dust Container
Always switch the vacuum off, then switch off at the power outlet and unplug prior to replacing filters or emptying the dust container.
For optimum use, the dust container should be emptied after every use.
When the dust container reaches the capacity mark ‘MAX’, it is essential to thoroughly clean both the dust container and filters.
To remove the dust container, ensure the vacuum is down on its wheels; remove the dust container by pressing down on the button on top of the dust container. Once released carefully lift the container upwards.
Fig. 9
To empty the dust container simply place it over the rubbish bin, ensuring the opening of the bin is larger than the dust container. Press the “PUSH” button located beneath the hose inlet connection on the front of the dust container. The bottom of the container will release and the dust and compiled dirt will be dispensed.
Fig. 10
NOTE: Dependant upon the amount and type of dirt collected in the dust container, it may be necessary to agitate the dirt inside the dust container for easier dispensing.
Fig. 8
IMPORTANT: Do not use the unit without a dust container in place.
10
Cleaning and
Replacing Filters
To assist you with the regular care of your vacuum, a second HEPA filter is supplied for convenient use, ideal for when a dirty filter is being cleaned.
NOTE: It is recommended that filters are cleaned after every use and replaced regularly to ensure maximum efficiency from your vacuum.
If filters are left uncleaned, it may result in a reduction of suction power.
Should this occur, the following procedure should be followed every couple of months.
NOTE: The performance indicator light may illuminate when filters need replacing or cleaning.
Procedure to Replace Filters
Always switch the vacuum off, then switch off at the power outlet and unplug prior to cleaning or replacing the filters. Before replacing the filters ensure all dirt and dust is first emptied from the dust container.
Refer to the ‘EMPTYING THE DUST
CONTAINER’ section.
1. Remove the dust container from the vacuum by pressing down on the button on top of the dust container. Once released, carefully lift the container upwards.
Your new vacuum cleaner includes a black foam filter casing which locks your foam filter to the front side of the HEPA filter. This is a reusable, removable part.
Fig. 11
2. To remove the HEPA filter from the back (flat side) of the dust container, press the tab and pull out the HEPA filter, followed by the foam filter and black casing.
Fig. 12
When conducting your routine cleaning of the filters, it is necessary to remove the black foam casing to separate the foam and HEPA filters for cleaning.
11
Care and Maintenance
continued
NOTE: A second HEPA filter is supplied for convenience, ideal for when a used filter is being cleaned.
Fig. 13
3. Shake and tap the HEPA filter until all the fine dust particles are removed. After approximately
6 months the HEPA filter should be replaced. This period is dependant upon the frequency of use and type of dirt being subjected to the vacuum.
The HEPA filter can also be hand washed in warm water.
NOTE: Do not use any detergents or boiling water to wash the filter, do not wash the filter in a dishwasher or washing machine.
It is advised to let the filter dry completely for at least a minimum of
24 hours before use.
NOTE: Do not dry in a tumble dryer, microwave, oven or near a naked flame. The filter and filter case must be completely dry before replacing into the vacuum. Failure to allow the filter to completely dry may result in damage to the vacuum motor.
Fig. 14
NOTE: When replacing the dust container HEPA filter, all three components (HEPA filter, foam filter and plastic casing) need to be replaced.
4. To place the filter back in the dust container, ensure that the filter is completely dry before use. Close the bottom of the container.
5. Simply place the foam filter into the black casing. When reassembling the filter casing, it is important to position the casing in its correct orientation against the foam filter. As demonstrated in Fig.12, the larger square compartments should be positioned at the same end as the locking tabs.
Then click the filter assembly into the back of the dust container.
12
NOTE: If the Canister does not easily fit in position, the filter casing may be in the wrong orientation. Do not force the dust canister back into position.
IMPORTANT: Dirty and clogged filters may result in reduced suction performance. It is recommended that filters are cleaned after every use and replaced regularly to ensure maximum efficiency from your vacuum. If filters are left uncleaned, it may result in reduction of suction power.
6. To remove and clean the
CaptivG3 cone from inside the dust container, firstly ensure the dust container has been emptied.
Follow the ‘EMPTYING THE DUST
CONTAINER’ instructions.
Press the ‘PUSH’ button located beneath the hose inlet connection on the front of the dust container.
The bottom of the container will release. Grip the two pockets at the base of the cone with two fingers, twist clockwise to ‘OPEN’ and pull to remove the cone.
Fig. 15
Fig. 16
Shake and tap the cone until all the fine dust particles are removed. The cone can also be hand washed. Allow the cone to completely air dry before re-assembling.
To replace the cone into the dust container, grip the two pockets at the base of the cone with two fingers, slide the cone into the allocated bracket inside the dust container and twist anti-clockwise to ‘CLOSE’ until resistance is felt.
13
Care and Maintenance
continued
Fig. 15
7. Place the dust container back in the vacuum cleaner for next use.
Exhaust Filter
The exhaust filter should be cleaned after every use for maximum vacuuming performance. To clean, simply unclip the grill at the back of the vacuum cleaner and shake and tap the filter to remove any dust accumulated. Then relocate the filter and reattach the grill.
14
Troubleshooting
Problem
Vacuum cleaner is not working
Vacuum cleaner is not picking up dirt
Dust escaping from vacuum
Possible Causes
• The unit may not be plugged into power outlet
• Dust container is full
• Filter is clogged
• Dust container is not fitted correctly
• Dust container is not fitted correctly
• Hose is not fitted correctly
• Dust container is full
What To Do
• Ensure the power plug is securely plugged
• Empty and clean the dust container
• Refer to ‘Cleaning and
Replacing Filters’, page 11
• Check dust container replacement
• Check dust container installation
• Check hose installation
• Empty and clean the dust container
Spare Parts
To order spare parts for your
Kambrook CaptivG3 Cyclonic Bagless
Vacuum please contact Customer
Service on:
1300 139 798 (Australia) and 0800 273 845 (New Zealand)
Replacement Filter Part No. KBF400
15
