Guía de instalación rápida

TK-401R

TK-801R

TK-1601R

Table of Contents

Español

1. Antes de iniciar

2. Instalación del Hardware

3. Funcionamiento

Technical Specifications

Troubleshooting

2

4

1

1

7

8

Version 08.14.2009

1. Antes de iniciar

Requisitos del sistema

Contenidos del paquete

(TK-801R/TK-1601R)

1

2. Instalación del Hardware

1.

Apague todos los PCs y sus periféricos, luego desconecte todos los cables de alimentación.

2.

Conecte el teclado compartido PS/2, el monitor y el ratón PS/2 al

puerto consola

del conmutador KVM.

(Ver imagen del TK-801R )

3.

Conectar el adaptador de alimentación AC incluido al conmutador KVM, y después a una toma de corriente. (sólo para el TK-801R y

TK-1601R).

4.

Utilice los cables PS/2 KVM para conectar su

PC al conmutador KVM.

5.

Encienda los PCs conectados uno por uno y espere hasta que aparezca el escritorio de cada PC.

2

PC 1, 2, 3, 4 (TK-401R)

PC 1, 2, 3, 4, 5, 6, 7, 8 (TK-801R)

PC 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12,

13, 14, 15, 16 (TK-1601R)

Para montaje en bastidor

El conmutador puede montarse sobre un bastidor de 19 pulgadas tamaño estándar EIA, que puede colocarse en un armario de empalmes junto con otros equipos.

Nota:

Si desea instalar el conmutador KVM a un bastidor de equipo EIA 19”, coloque las abrazaderas de sujeción a ambos lados del conmutador KVM, asegúrelas con los tornillos suministrados, y luego incorpore el conmutador KVM al bastidor del equipo con el hardware proporcionado por el fabricante

1.

Fije las abrazaderas de sujeción a ambos lados del conmutador KVM y asegúrelas con los tornillos suministrados.

2.

Coloque el conmutador KVM con cuidado encima del bastidor. Haga que la abrazadera coincida con los orificios de los tornillos del bastidor, luego use los tornillos suministrados junto con el bastidor del equipo para montar el conmutador KVM.

La instalación ha sido completada

Registre su producto

Para asegurar los más altos niveles de servicio y apoyo al cliente, registre su producto en línea en:

www.trendnet.com/register

Gracias por elegir TRENDnet

3

3. Funcionamiento

Nota

: Para la conexión entre PCs, se pulsan los boton del panel frontal o comandos

“Hot Key”.

Indicadores LED

LED con luz roja:

El cable KVM está conectado y el PC está haciendo funcionar el conmutador KVM.

LED con luz verde:

Indica que el puerto PC seleccionado está activo, independientemente de que el PC esté encendido o apagado.

LED Flash en verde:

El puerto PC seleccionado está en modo escanear o no ha sido activado por el PC.

Botones de arranque

Pulse los botones de arranque para la conexión entre PCs.

4

Comandos Hotkey

Un comando hotkey del teclado consiste en pulsar tres teclas:

Comando Hotkey = Scroll Lock + Scroll Lock + Tecla(s) de comando

Después de pulsar la tecla Scroll Lock, dispone de 2 segundos para pulsar la tecla

Scroll Lock otra vez. Ahora dispone de 2 segundos para presionar una tecla de comando. Si usted no pulsa una tecla en el plazo de 2 segundos, el conmutador saldrá del modo hotkey.

Para seleccionar un puerto PC específico:

Para TK-401R

Y = número de puerto 1-4 Scroll Lock + Scroll Lock +

Y

Por ejemplo para seleccionar el puerto 1 en el conmutador KVM debe presionar la siguiente secuencia de teclas

Scroll Lock + Scroll Lock + 1

Para TK-801R/TK-1601R

Scroll Lock

+

Scroll Lock +

Y + Z

Y Z = número de puerto 01-08 (TK-801R) ó número de puerto 01-16 (TK-160R)

Por ejemplo para seleccionar el

puerto 1

ó

puerto 10

en el conmutador KVM debe presionar la siguiente secuencia de teclas

Seleccionar puerto 1 =

Seleccionar puerto10 =

Scroll Lock

Scroll Lock

+

+

Scroll Lock +

Scroll Lock +

0 + 1

1 + 0

Para ver la lista de todos los comandos Hot Key, por favor consulte la hoja de referencia rápida.

5

Comando

Seleccionar sólo canal de PC

Canal próximo inferior

Canal próximo superior

Autoescanear el sonido Beep

Encendido/Apagado

Restablecer KVM

Autoscan (Escaneo automático)

Autoescanear con tiempo de retraso programado

Detener Autoscan

Hoja de referencia rápida para elTK-401R/801R/1601R

Teclas Hot Keys

Botones del panel

TK-401R

Scroll Lock + Scroll Lock + Y

(Y)= número de puerto de un (1) dígito (1-4)

TK-801R/TK-1601R

Scroll Lock + Scroll Lock + Y

(YZ)= número de puerto de dos (2) dígitos (01-16)

+ Z

Pulse el botón de arranque de un puerto específico para conectarse a ese puerto.

Descripción

Selecciona el canal activo de la PC.

Scroll Lock + Scroll Lock +

- - -

Seleccione el canal PC inferior más próximo

Scroll Lock + Scroll Lock +

Scroll Lock

+

Scroll Lock

+

Scroll Lock

+

Scroll Lock

+ END

Scroll Lock + Scroll Lock +

Scroll Lock + Scroll Lock + S

(X)= 5~99 segundos

+ X

Press any key on keyboard

B

S

- - -

Seleccione el canal PC superior más próximo

- - -

Active o desactive el sonido Beep durante el modo Autoescanear

- - -

- - -

- - -

Pulse cualquier botón

Restablecer KVM

Autoescanear cada canal conectado para una rápida lectura en pantalla de cada canal

Autoescanear cada canal conectado para una rápida lectura en pantalla de cada canal en intervalos de X segundos.

Finaliza el escaneo automático.

6

Technical Specifications

Management

Console Port Connectors

(all famale)

PC Port Connectors

(all female)

VGA Resolution

Port Selection

LED

Keyboard State

Auto-Scan Intervals

Power

Dimensions

Weight

Temperature

Humidity

Certifications

TK-401R: 4 computers

TK-801R: 8 computers

TK-1601R: 16 computers

1 x PS/2 keyboard 6-pin mini din

1 x PS/2 mouse 6-pin mini din

1 x VGA HDB15 15-pin

4/8/16 x PS/2 keyboard 6-pin mini din

4/8/16 x PS/2 mouse 6-pin mini din

4/8/16 x VGA HDB15 15-pin

1920 x 1440

Push Button and Hot Key Commands

Link (Green), Active (Red)

Save and restore

5 ~ 99 seconds

PS/2 Interface Power

External AC Power Adapter : 9V DC, 1A (TK-801/TK1601 only)

TK-401R: 202 x 104 x 45mm (8.0 x 4.1 x 1.8 in.)

TK-801R: 407 x 165 x 45mm (16.0 x 6.5 x 1.8in.)

TK-1601R: 406 x 165 x 85 mm (16.0 x 6.5 x 3.4 in.)

TK-401R: 835g (1.84lb.)

TK-801R: 1.9 kg (4.2 lbs)

TK-1601R: 2.65 kg (5.85 lbs)

Operating: 0° ~ 40° C (32° ~ 104° F)

Storage: -20° ~ 60° C (-4° ~ 140° F)

0% ~ 90% Non-Condensing

CE and FCC

7

Troubleshooting

Do I need to use the included external AC adapter?

It is recommended that you use the included external AC adapter with the TK-801R/

TK-1601R KVM switch.

I have the KVM switch connected properly, but my keyboard and mouse don't work.

Please make sure your PS/2 ports are working properly by testing it with another mouse or keyboard. Once you confirm that the PS/2 ports are functional, please reboot your computers, and try to use the KVM switch again.

Can I connect or disconnect the KVM cables while the computers are turned on?

Yes, you can connect or disconnect the KVM cables while the computers are turned on, because the interface is Hot-Pluggable.

Will the KVM switch restore the keyboard settings between computers?

Yes, the KVM switch will restore the keyboard settings when switching between computers.

(i.e.: Cap Lock, Num key, etc.)

How do I switch from one computer to another with the KVM switch?

You can switch computers by pressing the Push Buttons on the KVM switch or using the Hot

Key commands.. Go to Section 3 Operation for more information.

If you still encounter problems or have any questions regarding the

TK-401R/TK-801R/TK-1601R

, please contact Trendnet's Technical Support Department.

8

Limited Warranty

TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase.

TK-401R/ TK-801R/TK-1601R - 2 Years Limited Warranty

AC/DC Power Adapter, Cooling Fan and Power Supply carry a 1 year limited warranty

If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer. The repair/replacement unit's warranty continues from the original date of purchase. All products that are replaced become the property of TRENDnet. Replacement products may be new or reconditioned. TRENDnet does not issue refunds or credit. Please contact the point-of-purchase for their return policies.

TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty.

There are no user serviceable parts inside the product. Do not remove or attempt to service the product by any unauthorized service center. This warranty is voided if (i) the product has been modified or repaired by any unauthorized service center, (ii) the product was subject to accident, abuse, or improper use (iii) the product was subject to conditions more severe than those specified in the manual.

Warranty service may be obtained by contacting TRENDnet within the applicable warranty period and providing a copy of the dated proof of the purchase. Upon proper submission of required documentation a Return Material Authorization (RMA) number will be issued. An RMA number is required in order to initiate warranty service support for all TRENDnet products.

Products that are sent to TRENDnet for RMA service must have the RMA number marked on the outside of return packages and sent to TRENDnet prepaid, insured and packaged appropriately for safe shipment. Customers shipping from outside of the USA and Canada are responsible for return shipping fees. Customers shipping from outside of the USA are responsible for custom charges, including but not limited to, duty, tax, and other fees.

9

WARRANTIES EXCLUSIVE

: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS

WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT TRENDNET'S

OPTION, REPAIR OR REPLACE. THE FOREGOING WARRANTIES AND REMEDIES ARE

EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,

EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME

FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION

MAINTENANCE OR USE OF TRENDNET'S PRODUCTS.

TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND

EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT

EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT,

IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR

MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY

ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.

LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO

EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN

CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL,

INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE

OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER

FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION,

MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE

POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR,

REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET'S OPTION.

THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY

REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.

Governing Law

: This Limited Warranty shall be governed by the laws of the state of California.

Some TRENDnet products include software code written by third party developers. These codes are subject to the GNU General Public License ("GPL") or GNU Lesser General Public License

("LGPL").

Go to http://www.trendnet.com/gpl or http://www.trendnet.com

Download section and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers.

TRENDnet does not provide technical support for these codes. Please go to http://www.gnu.org/licenses/gpl.txt

or http://www.gnu.org/licenses/lgpl.txt

for specific terms of each license.

PWP05202009v2

10

Certifications

This equipment has been tested and found to comply with FCC and CE Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received. Including interference that may cause undesired operation.

Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local

Authority or Retailer for recycling advice.

NOTE:

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS

EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO

OPERATE THE EQUIPMENT.

ADVERTENCIA

En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria existente en el pais o zona de instalación.

Product Warranty Registration

Please take a moment to register your product online.

Go to TRENDnet’s website at http://www.trendnet.com/register

Copyright ©2009. All Rights Reserved. TRENDnet.