creative touch 1030

creative touch 1030
TNT REPAIR
SINGER FUTURA 900/920 – Creative Touch 1030/1036 Machines
Panel Removal Guide
This guide will also apply to the 900, 925, 935, 1030, 1036, 1411, 1425 Athena Class 1200, 2000, 2005 and Touch Tronic’s
2001, 2010, series machines. Or basically any model built on the Futura type of frame design. I believe I’ve covered most of
the models, but may have missed some.
Basic Tool Requirements:
Screwdriver small blade
Screwdriver short handled type
Screwdriver Phillips type #2
Screwdriver Medium Flat blade type
Allen Wrench 3/32
Allen Wrench 5/64
Flat bar stock that has a true square flat edge. Or the 900/920 gauge,
which also helps adjust feed dog height. At least 1/16th thick, and at
least 2 inches in length. Basically all you need is something with a
true straight flat edge that will fit between the thumbnut screw for the
presser foot, and the presser bar guide. Now if the machine has really
been tampered with, the presser bar guide could be out of adjustment,
but general rule of thumb, it should be ok. The screw that holds it in
place is buried behind the buttonholer lever, and not that easy to
reach.
Preparing The Machine: (Note: Ensure machine is set to straight stitch, required for timing hook to needle)
Open the top cover to expose the pattern, and stitch width, needle position dials, (Fig 1). Ensure the machine is set
for straight stitching, and center needle position
Set the presser bar pressure dial to “Darn” (Fig 1, item a)
Remove the pattern selector dial by pulling it straight upward, as indicated by the Red Arrow, (Fig 1)
Remove the pattern selector-unlocking dial, reference (Fig 2), by using a small bladed screwdriver, and very gently
relieving the pressure lock tab away from the dial. The dial will then spin counter clockwise some, and lift up and
off the locking mechanism
Remove the top cover screws (3 qty), indicated by the blue circles
Remove the side cover screw (Fig 3) (Note, some models may be equipped with a pinch screw here - Fig 3a)
Remove the side cover by sliding it off, gently pull is straight off, as part does engage the top left cover screw
Remove the top, by lifting from the back first, and gently lifting upwards at an angle towards you as you face the
machine.
a
Fig 1
Fig 3
Fig 2
Fig 3a
Back of machine
Fig 4
Once the top and side cover are removed, lay the machine on its back, Fig 4, and remove the pan screws. Indicated
by the blue circles
Once you have the top covers, and bottom pan off, we need to remove the front panel. Fig 1, black arrow.
Cover Removal Steps:
1. Remove the 2 screws that hold the front panel on, Fig 2
2. Remove the light lens cover, Fig 3. Work the lens cover in a
downward motion, it should slid right off, but if necessary,
loosen the screw holding the lens cover to the socket
3. Remove the hand wheel by removing the Philips screw
holding it to the gear/belt drive unit. Fig 4. The hand wheel
should slide off with little to o resistance.
4. Remove the Pattern Panel, Fig 1, Yellow Arrow
Fig 1
Fig 2
Fig 3
5.
6.
Remove the stitch length
indicator dial, Fig 5. The dial just lifts straight off
the machine
Remove the pattern indicators light shield, Fig 6.
You’ll find it easiest to lift the shield upwards on the
left side, move it backwards over the frame rest, and
then angle it with the left side downward. The shield
will exit the machine mainly from the right side
when angled correctly
Fig 4
Fig 6
Fig 5
Cover Removal Steps: (continued)
7. To remove the front cover, position it as shown in Fig 7. Work the right side upwards, while positioning the left
side downwards to clear the light socket. It’ll help to push the stitch lever down, as you would when sewing in
reverse (or back tack), and then work the front
cover off the machine.
Fig 7
www.tandtrepair.com
[email protected] or [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement