AND AX-HA-CHG Instruction manual

( ᪥ᮏㄒࡢྲྀᢅㄝ᫂᭩ࡣ཯ᑐ㠃ࢆࡈぴࡃࡔࡉ࠸㹿 )

AX-HA-CHG

Charging hanger

Instruction Manual

2014 A&D Company, Limited. All rights reserved.

No part of this publication may be reproduced, transmitted, transcribed, or translated into any language in any form by any means without the written permission of A&D Company, Limited.

The contents of this manual and the specifications of the instrument covered by this manual are subject to change for improvement without notice.

1WMPD4003017

Safety Use

When using this device, be sure to observe the following:

Caution

Do not disassemble the product. Any damage or loss of functions caused by disassembly is not covered by warranty.

Do not link more than three charging hangers. Linking four units or more may cause fire or damage the units or the MPA series of electronic pipettes.

Caution During Use

Caution

Use the AC adapter provided for the MPA series of electronic pipettes, otherwise the charging hanger, the

MPA electronic pipettes, or the power supply devices may be damaged.

1. Introduction

This manual describes how the AX

-HA-CHG charging hanger works. Please read this manual carefully before using the hanger in order to get the most out of its performance. Please read the manual for the MPA series of electronic pipettes as well.

2. Unpacking the Charging Hanger

Charging hanger main unit

Self tapping screw, 4 mm diameter x L8 mm (2 pcs ) cable

-KO4730-10)

Instruction manual (This manual) ձ Power indicator LED ղ մ

Fixing screw holes

Double-stick tape յ Input section ճ Charging terminals ն

Charging hanger main unit

Output section

Self tapping screw, (2 pcs)

For plastic and wood

Linking cable (10 cm long)

(AX

-KO4730-10) ձ Power indicator LED: Lights up in green when power is supplied to the charging hanger. ղ Fixing screw holes: Used when securing the charging hanger with screws pipettes for charging մ Double-stick tape: Used for securing the charging hanger to a wall, etc. յ Input section: Connects with the cable from the AC adapter

(connects with Mini USB

– Type B) ն Output section: Used for linking multiple charging hangers

3. Features

onto the charging hanger.

The charging hanger can be freely mounted to a wall, rack, etc. (secured with double-stick tape or screws).

With use of the linking cable, one AC adapter can supply power to more than one charging hanger (up to three units).

4. How to Use

ձ Secure the charging hanger to a wall or rack with the double-stick tape after removing dirt from the surface

(securing with screws is also possible).

Release liner Self tapping screw

Securing with double-stick tape Securing with screws ղ Prepare the AC adapter and power cable that come with the electronic pipette. ճ Connect the power cable to the AC adapter and insert the AC adapter into a power source.

Power cable

AC adapter մ Connect the power cable (Mini USB – Type B) to the input section of the charging hanger. The power indicator LED (green) will light up.

䯲 To link multiple units, connect the linking cable to the output section of the hanger.

Mini USB – Type B

ͤ Mind the direction

䯲 For

AX

-KO4730-10 յ Hook the electronic pipette onto the charging terminals of the hanger to begin charging. Once charging starts the battery indicator at the bottom left of the pipette display will blink as shown in the following figure. ն Charging is complete when the battery indicator of the pipette is fully lit. Fully charged շ The electronic pipette can continue to be hooked to the charging hanger after it is fully charged. (It will not be recharged.)

5. Linking Multiple Units

Up to three charging hangers can be used in conjunction. (Two linking cables are required.)

6. Specification

Input (AC adapter) AC 100 V / 0.3 A (50 / 60 Hz)

Input section / output section

Connectable devices

Number of units linkable

Dimensions

Net weight

5 V

MPA series

3 units maximum

60 (W) × 50 (H) × 58 (D) mm

Approx. 50 g

(Excluding AC adapter and Linking cable)

7. Accessories

Linking

-KO4730-10

Dedicated AC adapter for the MPA series AX-TB-265

(Standard accessory for the MPA series of electronic pipettes)

- 1 - - 2 - - 3 - - 4 -