Velodyne MicroVee User`s manual

U S E R ’ S

M A N U A L

A u d i o / V i d e o S u b w o o f e r S y s t e m

.

w w w . v e l o d y n e . c o m

MicroVee User’s Manual

Table of Cont ents

Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Placement of Your Subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

LFE Connection - Option A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

MINI-JACK Connection - Option B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Speaker-Level Connection - Option C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Interconnnect Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Care of Your Subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Protection Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Troubleshooting and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Velodyne Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

.

w w w . v e l o d y n e . c o m

MicroVee User’s Manual ii

Congratulations on your purchase of a Velodyne MicoVee subwoofer system! This system represents the state-of-the-art in low frequency reproduction and will provide you with years of listening pleasure when properly used and cared for. Read and follow this instruction manual to insure safe and proper system connection and operation.

Warning!

To prevent fire or shock hazard, do not expose this equipment to rain or moisture. To avoid electrical shock, do not open speaker enclosure or amp chassis cover. Please observe all warnings on the equipment itself. There are no user serviceable parts inside. Please refer all service questions to your authorized Velodyne dealer or service representative.

Note: Do not leave unit in direct sunlight or use in high humidity environments!!!

P r i o r t o I n s t a l l a t i o n

Please unpack the system carefully. This unit is heavy. Use caution when lifting or moving to avoid injury. Four rubber feet are included with your subwoofer and are located in the styrofoam packing. Before installing your MicroVee, peel off the adhesive backing and attach the feet to the bottom of the subwoofer.

Please save the carton and all packaging materials for future use. Packing this unit in any other carton may result in severe damage when shipping. Record the serial number in the space provided on the warranty card for future reference.

P r o d u c t F e a t u r e s a n d C o n t r o l s

• Drivers consisting of:

- Active 6.5” (5” piston diameter) driver with 2” high-temp voice coil and,

- Dual passive radiators 6.5” (5” piston diameter)

• Built-in 1200 watt Dynamic/600 watt RMS high efficiency Class D amplifier

• Adjustable (50 to 200 Hz) low-pass crossover (defeatable)

• Line-level (mini-jack) inputs and outputs

• LFE Input

• Speaker-level inputs

• Speaker-level outputs with 120 Hz high-pass crossover

• Signal sensing auto turn on/off (active/inactive)

• Variable volume control

• Selectable phase control (0° or 180°)

• Multiple staggered low-pass crossovers; 12 dB/octave initial, 48 dB/octave ultimate

• Driver Displacement Control circuit to prevent over excursion and amp clipping

• High-excursion rubber surround

• Oversized spider for linearity at high excursion

.

w w w . v e l o d y n e . c o m

MicroVee User’s Manual 1

Placement of Your Subwoofer

The first step in installing your new MicroVee is to determine where it will be placed in the room.

Unpack the system carefully and use the following guidelines in order to find the best room placement option.

True subwoofers operate at extremely low frequencies which are primarily omni-directional.

Keep in mind that frequency response and output level can be drastically influenced by placement, depending on the acoustic properties of the listening room. To obtain optimum output from your subwoofer, place it within a foot of a corner. This location will offer the greatest output levels and optimum low frequency extension. If at all possible, your subwoofer should be placed along a wall. The worst location for a subwoofer is typically far away from any walls and close to the center of your room. Avoid these locations when possible. When using a pair of

Velodyne subwoofers in stereo, it is preferable to place each subwoofer near the satellite of the same channel.

Depending on the size and type of furnishings in the room, perfect placement may not be possible.

Finding the best location within your environment will likely require some experimentation. We suggest you experiment with the location during setup to find what sounds best to you when seated in your typical listening position.

Regardless of where you install your Velodyne subwoofer, it must remain in an upright position

(woofer facing forward). Using, shipping or storing the subwoofer in any other position for an extended period of time may result in damage to the unit not covered by warranty.

Caution! This subwoofer has electronics built into the cabinet. Do not place the cabinet next to sources of heat such as furnace registers, radiators, etc. Do not place the unit near sources of excessive moisture, such as evaporative coolers, humidifiers, etc. The power cord should be routed in such a way that it will not be walked on, pinched or compressed in any way that could result in damaging the insulation or wire.

.

w w w . v e l o d y n e . c o m

MicroVee User’s Manual 2

Ins tallation

Your new Velodyne subwoofer provides for a number of installation options. Read all the installation information below in order to determine which installation option is best suited for your system. Remember to perform all installation procedures with system power turned off to prevent possible damage.

Figure 1. MicroVee Back Panel

I n p u t s

Your new subwoofer is equipped with speaker-level, line-level, and MINI-JACK inputs. Use the

LINE LEVEL jacks when connecting your subwoofer to a pre-amp, signal processor, line-level crossover or receiver with pre-amp level outputs. The SPEAKER LEVEL jacks connect directly to the speaker outputs of any amplifier, integrated amplifier or receiver. Your amplifier section will notice no additional loading effects when you use these inputs due to their very high impedance. Use the MINI-JACK inputs when connecting to a docking station or personal audio system.

Important!!! Do not use any of the LINE LEVEL, SPEAKER LEVEL, and MINI-JACK connections simultaneously!

.

w w w . v e l o d y n e . c o m

MicroVee User’s Manual 3

M I N I - J A C K T h r u

This connection passes along the input signal from the MINI-JACK input unchanged.

S p e a k e r L e v e l O u t p u t

These speaker level connections connect to your main speakers. There is 120 Hz high-pass crossover that removes the bass frequencies from your main speakers. This frees them of the burden of playing bass, which makes the entire system perform better.

V o l u m e C o n t r o l

This control allows you to balance the output from the subwoofer to the main speakers in your system. This control should be set to achieve similar output level from both the main speakers and subwoofer when listening to music. A good starting point for the volume control is three or four dots from minimum.

WARNING: Some manufacturers preset their receivers with the Sub-Out channel signal at a minimum level. It is very important to verify that your receiver Sub-Out channel is set to the same output level as your front right and left channels. Refer to your receiver manual for the individual channel level adjustment procedure. If your receiver Sub-Out channel is set too low, the subwoofer may appear to have a weak output, it may sound noisy or distorted, and the

Auto On/Off feature may not operate properly.

L o w - p a s s C r o s s o v e r - 5 0 t o 2 0 0 H z

All inputs sum the left and right channels together, with the resulting signal passing through an adjustable low-pass crossover before being amplified. The crossover control allows you to adjust the upper limit of the subwoofer’s frequency response from 50 to 200 Hz. The subwoofer’s response will begin rolling off above the frequency you set this control to. You should set the crossover frequency to obtain a smooth and seamless transition from the subwoofer to the main speakers in your system. If your main speakers are smaller with limited low frequency output, you may wish to choose a higher frequency (such as 100 -120 Hz) than you would with larger speakers which have greater low frequency output. With larger speakers, you might start with this control set lower, such as 80 Hz.

P h a s e A d j u s t m e n t - 0 ° / 1 8 0 °

This control allows you to “reverse” the phase of the subwoofer’s output signal 180° to correct for any possible mismatch and resulting cancellation between the subwoofer and your main speakers. To adjust, simply listen to the system with music playing. Then move the switch from one position to the other and listen for a change in low frequency output. The correct position will have a greater amount of apparent low frequency output.

C r o s s o v e r S w i t c h - I N T E R N A L X - O V E R / S U B W O O F E R D I R E C T

This switch allows the MicroVee’s internal crossover circuitry to be bypassed. This is required in certain installations which route the signal through external processors with a crossover circuit of their own. Simply move the switch to SUBWOOFER DIRECT to disengage the built-in crossover. For all other installations which do not have a separate electronic crossover, we recommend you leave the switch set to INTERNAL X-OVER to provide optimum performance.

NOTE: This is explained further in the section below entitled “A Word About Crossovers”.

.

w w w . v e l o d y n e . c o m

MicroVee User’s Manual 4

A u t o Tu r n O n F u n c t i o n

With this function in the “active” position, your subwoofer can be safely left with the main power switched on continuously. The subwoofer will turn itself on automatically when an audio signal is present. If no signal is present for approximately 15 minutes, the unit will switch to standby mode. While in standby mode, your subwoofer will draw very minimal power. This function can be disabled by leaving the switch in the “inactive” position.

WARNING: If the Sub-Out channel signal level from your receiver is too weak, this feature will not operate properly. See VOLUME CONTROL section on previous page.

P o w e r S w i t c h

The master power switch is located on the lower half of the unit. This rocker style switch is the main on/off control for the unit. This switch should be set to position 1 (up) for on, and

0 (down) for off. If the unit is to be left unused for an extended period of time, the master power switch should be turned off.

A W o r d A b o u t C r o s s o v e r s

The MicroVee is designed to operate using the full range audio signal as input. Some processors/receivers have a “subwoofer out” (or LFE) jack, which is the ouput of the receiver’s crosssover, that is, signal that has already had the upper frequencies removed. Consult your receiver’s owner’s manual on adjusting this setting. In some rare cases, combining both the receiver’s crossover and the one internal to the subwoofer may result in low output and increased noise. In these installations you may need to bypass the crossover in either the processor or the MicroVee. In some installations, simply setting one crossover to a higher frequency (such as 120 Hz) will restore maximum performance. To bypass the subwoofer’s internal crossover when the unit is being fed a low pass signal from another crossover, simply locate the switch marked INTERNAL X-OVER/SUBWOOFER DIRECT on the rear panel of the subwoofer and set to the SUBWOOFER DIRECT position. This will eliminate the MicroVee’s crossover from the signal path.

.

w w w . v e l o d y n e . c o m

MicroVee User’s Manual 5

LFE Connection - Op tion A

Figure 2 shows connection from your home theater receiver to the LFE input on the back of your subwoofer. When the subwoofer is installed in this fashion, all of the low frequency information from your “LFE Out” or “Subwoofer Out” on the back of your receiver will pass into your Velodyne subwoofer. This connection is the most common connection method when using your subwoofer with a 5.1 receiver. (Cable needed: 1 mono RCA cable.)

Figure 2. Installation Using LFE Line-Level Inputs

.

w w w . v e l o d y n e . c o m

MicroVee User’s Manual 6

A W o r d A b o u t T h e A u t o O n / O f f F e a t u r e

When using a single channel input (such as a surround sound processor’s subwoofer out or

LFE), the auto on/off circuit sensitivity will be affected. When one input channel is used instead of two, the unit will see lower signal levels present at the inputs. This may cause the unit to turn off inadvertantly when listening at low volume levels and/or not “wake up” even when signal is present. If this occurs, simply use a “Y” adapter (available from most dealers) to allow your processor’s single sub line to be fed into both L&R inputs. This will make the unit turn on at lower signal levels.

.

w w w . v e l o d y n e . c o m

MicroVee User’s Manual 7

Mini-Jack Connection - Op tion B

Figure 3 shows connection from your audio player or gaming console output to the MINI-JACK of your Velodyne subwoofer. Use the supplied cable to connect from the output of your dock, computer or gaming console to the input jack of the MicroVee. Connect the satellite speakers into the thru-jack on the back of the MicroVee subwoofer. (Cable supplied by Velodyne: 6 foot,

1/8” (male) to 1/8” (male) stereo cable.)

Figure 3. Installation Using Mini-Jack Line-Level Inputs .

w w w . v e l o d y n e . c o m

MicroVee User’s Manual 8

Speak er -Le v el Connection - OPTION C

Figure 4 shows an easy way to connect your Velodyne subwoofer directly to your receiver or integrated amplifier if it lacks line-level outputs. You may also connect your satellites directly to your receiver or amplifier along with the subwoofer. Your receiver or amplifier will not notice the additional load of the subwoofer due to the high input impedance.

When the subwoofer is installed in this fashion, your satellite speakers will be crossed over at

120 Hz which removes the lower bass frequencies from your speakers, enabling them to do a better job reproducing the higher frequencies.

.

Figure 4. Installation Using Speaker-Level Inputs w w w . v e l o d y n e . c o m

MicroVee User’s Manual 9

Caution!!! To avoid damage to your main amplifier, be sure to maintain correct polarity when making all connections. Red (positive) to red, and black (negative) to black. Be sure that all connections are tight, and that there are no loose strands or frayed wires.

Int erconnect Cables

When installing your new Velodyne subwoofer using the line level connections, you should always use shielded phono cables. There are many quality cables available. We recommend that you keep the length of cable as short as possible to avoid any potential noise problems.

When using speaker level connections, use a quality speaker wire that mates well with the connectors. Be very careful to avoid any loose strands or frayed wires which may result in a short which may in turn, damage your equipment. Extremely large gauge wire may not properly fit in the binding posts, resulting in a poor connection and possible short circuits.

Care of Your Subwoofer

Your Velodyne subwoofer does not require any regular maintenance. Normal dusting or cleaning of the surface for appearance purposes are all that is required. We suggest you avoid any harsh detergents or chemicals when cleaning the cabinet. Abrasives, detergents, or cleaning solutions may damage the finish on the cabinet. We recommend using only a damp cloth to clean the cabinet.

During normal conditions, your new subwoofer may be left on continuously without any problems. The unit is equipped with a signal-sensing turn on/off that will automatically turn on the unit when a signal is present at the inputs and turn off the unit after several minutes when there is no longer any signal at the inputs. If you plan to leave the subwoofer unused for an extended period of time, we recommend that you turn off the master power switch on the rear panel.

Prot ection Circuitry

Your new subwoofer is equipped with special protection circuitry to provide maximum performance with greatest reliability.

The unit is protected against:

1) Overdriving the speaker or amplifier

2) Overheating the amplifier

3) Excessive drop in power line voltage

The first type of protection circuitry which prevents overdriving of the speaker or amplifier operates constantly without being audible under most situations. In some extreme situations

(sustained high output levels such as pro sound usage), the unit may shut down momentarily.

This indicates the thermal or under-voltage protection circuitry has engaged. If this should happen, you should reduce the volume setting or shut the unit off until normal operating conditions return. You may also want to plug the unit into a different wall outlet, as dropping power line voltage will be most noticeable under strenuous conditions and may result in the unit shutting down intermittently.

.

w w w . v e l o d y n e . c o m

MicroVee User’s Manual 10

T roubleshooting and Service

Before seeking service for your subwoofer, please follow this simple troubleshooting guide to assist you.

1. Verify that the unit is plugged in, power outlet used is active and supplying proper voltage.

2. Is the power switch on?

3. Is the auto turn on/off (active/inactive) set properly?

4. Is the unit receiving an input signal from your source?

5. Have all controls on the subwoofer (volume, crossover, phase, etc.) been properly set?

6. If unit has been running at high levels for an extended period of time, one of the protection circuits may be engaged.

• Is the built-in amplifier extremely hot to the touch?

• Is your power line voltage sagging below acceptable levels?

If the protection circuitry is active, the unit may cycle on and off until operating parameters return to normal. Under more serious conditions, the unit may shut off completely. Normal operation will return upon cooling, but you may be required to turn the power off and then on again to reset the unit.

The following conditions require service by a qualified technician:

1. The power cord has become damaged.

2. The unit does not appear to operate normally or exhibits a marked change in performance.

3. The unit has been exposed to water.

4. Some part of the cabinet or circuitry is physically damaged.

Thank You for Purchasing a Velodyne!

.

w w w . v e l o d y n e . c o m

MicroVee User’s Manual 11

Specifications

Specifications

Driver

Passive Radiators

Amplifier

(Class D)

Low-Pass Crossover

Auto On/Off

Cone

Frequency Response

Harmonic Distortion

Magnet Structure

Voice Coil

Inputs

Outputs

Phase

Video Shielded

Dimensions (H/W/D)

(includes grille)

Cabinet

Warranty

(parts/labor)

Shipping Weight

(approx.)

MicroVee

6.5” forward firing

(5” piston diameter)

Dual 6.5” side-firing

(5” piston diameter)

1200 watts Dynamic

600 watts RMS power

50 Hz - 200 Hz (adjustable)

12 dB octave initial,

48 dB octave ultimate

Yes

Anodized aluminum

38 - 120 Hz (+/-3 dB)

<5% (typical)

64 oz.

(4 lbs)

2” Dual Layer

Speaker-level, mini-jack and gold plated line-level

Speaker-level (120 Hz high-pass crossover), mini-jack (thru)

0° or 180° (selectable)

No

9” x 9” x 9.6”

(22.9 x 22.9 x 24.4 cm)

Sealed enclosure

Three years (electronics - parts and labor),

Five years (drivers - parts and labor)

20 lbs. (9.1 Kgs)

.

w w w . v e l o d y n e . c o m

MicroVee User’s Manual 12

FOR YOUR RECORDS. . .

Date Puchased_________________________________________________________________

Dealer_________________________________________________________________________

Serial #________________________________________________________________________

*NOTE: Please complete and return your warranty card within ten (10) days or

Register. . . ON LINE . . . It’s faster . . . and easier www.velodyne.com

LIMITED WARRANTY

VELODYNE ACOUSTICS, Inc. (“VELODYNE”) warrants all electronics for a period of three years, drivers for a period of five years, and full range speakers for a period of five years. All VELODYNE products have a warranty from the date of purchase against defects in materials and workmanship subject to the following conditions:

1.

VELODYNE is not responsible for defects which result from the use of an amplifier or controller other than the one originally supplied with the unit (subwoofer) or defects which result from modifications or repairs made by any component of the system by anyone other than a VELODYNE factory authorized service representative.

2. This warranty is void if any repairs or service covered by the terms of this warranty are made to any component of the system by anyone other than a VELODYNE factory authorized service representative.

3. VELODYNE is not responsible for damage caused by accidents, abuse, misuse, natural or personal disaster or unauthorized modification. The VELODYNE products are not intended for professional or commercial use and VELODYNE is not responsible for damage resulting from such use.

4. The VELODYNE product warranty is limited to units that are purchased from authorized VELODYNE dealers and finalized within authorized dealer locations.

5. This warranty is nontransferable under any condition.

TO OBTAIN SERVICE

Information regarding service may be obtained from the dealer from whom you purchased the unit, or by contacting

VELODYNE customer service. Warranty service must be performed by a VELODYNE factory authorized service representative within the warranty period set forth above. If VELODYNE determines the unit is defective, VELODYNE will, at VELODYNE’s option, repair or replace the product at no charge if the product is forwarded prepaid to a factory authorized service representative. Products forwarded to the factory authorized service representative should be shipped securely and properly packaged, insured and freight prepaid.

.

w w w . v e l o d y n e . c o m

MicroVee User’s Manual 13

Velodyne Products

DD-10

DD-12

DD-15

DD-18

Digital Drive 1812

Signature Edition

DLS™-R Series

DLS-3500R

DLS-3750R

DLS-4000R

DLS-5000R

DPS™ Series

DPS-10

DPS-12

MicroVee™

MiniVee

®

120V

SPL™-R Series

SPL-800R

SPL-1000R

SPL-1200R

SPL-1500R

SubContrator™

Series

SC-1250

SC-8

SC-10

SC-12

SC-15

SC-IW

SC-IF/IC

VRP Series

VRP-1000

VRP-1200

VX™ Series

VX-10

SMS™-1

DD-10

DD-12

DD-15

DD-18

Digital Drive 1812

Signature Edition

CHT-R Series

CHT-8R

CHT-10R

CHT-12R

CHT-15R

230V

SMS™ -1

SPL-800i

SPL™-R Series

SPL-800R

SPL-1000R

SPL-1200R

SPL-1500R

SubContrator™

Series

SC-1250

SC-8

SC-10

SC-12

SC-15

SC-IW

SC-IF/IC

.

w w w . v e l o d y n e . c o m

MicroVee User’s Manual 14

Velodyne Acoustics, Inc.

345 Digital Drive

Morgan Hill, CA 95037

408.465.2800 voice

408.779.9227 fax

408.779.9208 service fax www.velodyne.com

Service E-mail: [email protected]

Product E-mail: [email protected]

Technical E-mail: [email protected]

63-MICROVEE Rev D JUL07 .

w w w . v e l o d y n e . c o m

MicroVee User’s Manual 15