PCC-550M Master

PCC-550M Master
PCC-550M PC Master
WIRING INFORMATION
Publication version 2.0
September 2002
268 Montague Rd, West End,
Brisbane, Australia, 4101
PCC-550M PC Master – Wiring Information
About this document
The purpose of this document is to provide a complete wiring description,
of the selected JACQUES product.
It shows cable connections, wiring diagrams and any other details that
are required to correctly install this product.
Due to its highly technical nature, this document is intended to be used
by suitably qualified Technicians or Engineers.
For further information on the range of JACQUES products, please refer
to the separate JACQUES Intercom Systems – A Guide to
understanding the JACQUES Intercom Systems document.
For further details about JACQUES Intercom features and designs,
please read the Architects and Engineers Specification ver 2002.
These documents can be read from the website at: www.jacques.com.au
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Web: http://www.jacques.com.au
268 Montague Road, West End,
Queensland, Brisbane, Australia 4101.
Email: [email protected]
2
268 Montague Rd, West End,
Brisbane, Australia, 4101
PCC-550M PC Master – Wiring Information
Contents
Wiring -------------------------------------------------------- 4
Connections ----------------------------------------------- 4
Two OPTIONS of Wiring ------------------------------- 4
RS-232------------------------------------------------------ 4
Microphone ------------------------------------------------ 4
Monitor Speaker------------------------------------------ 5
PTT Switch ------------------------------------------------ 5
Connections of OPTION 1----------------------------- 6
Wiring Diagram OPTION 1 ---------------------------- 7
PCC-550M Master ------------------------------------- 7
Controller ------------------------------------------------- 7
Operator’s Console ------------------------------------ 7
Connections of OPTION 2----------------------------- 9
Wiring Diagram OPTION 2 ---------------------------- 10
PCC-550M Master ------------------------------------- 10
Controller ------------------------------------------------- 10
Operator’s Console ------------------------------------ 10
Wiring Table ----------------------------------------------- 12
Other Information ---------------------------------------- 12
Copyright © 1980 – 2002
Jacques Electronics Pty Ltd ABN 11 010 416 323
Jacques Technologies Pty Ltd ABN 48 074 448 712
The material in this document is protected by copyright under the laws of Australia.
You may view this document and its contents and save an electronic copy, or print out a copy solely
for your own information, research or study, but only if you:
● Do not modify the copy from how it originally appears unless expressly authorised by Jacques
Electronics Pty Ltd and then only in accordance with Jacques conditions.
● Include the copyright notice “© Jacques Electronics Pty Ltd” on the copy.
You must not reproduce, frame, transmit (including broadcast), adapt link to or otherwise use any of
the material on this document, except as expressly permitted by agreement with Jacques Electronics
Pty Ltd , by statute or with Jacques Electronics Pty Ltd prior written consent.
Jacques Electronics Pty Ltd reserves the right to continually improve products and updating any
equipment specifications, document context and design styling and then passing this information onto
this document.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Web: http://www.jacques.com.au
268 Montague Road, West End,
Queensland, Brisbane, Australia 4101.
Email: [email protected]
3
268 Montague Rd, West End,
Brisbane, Australia, 4101
PCC-550M PC Master – Wiring Information
Wiring
Connections
The JACQUES PCC-550M PC Master Station is connected to a
JACQUES Controller and Operator’s Console, via a Master Cable.
Two OPTIONS of Wiring
! The Master Cable can be wired in one of two ways (two OPTIONS).
Both options use a Microphone, Monitor Speaker and PTT Switch, but
only the PTT Switch is wired differently between the options.
RS-232:
Cat-5 twisted pair data cable is used for the RS-232 communications
from PCC-550M Master to the Controller.
The PC Master uses its COM Serial Port (generally COM2), located at
the back of the PC and can be either a DB9 or DB25 type connector.
! Note that the connecting cable uses RS-232 protocol and as such, it
has a maximum cable distance of 10 Metres.
Microphone:
The Microphone is located on the Operator’s Console. It is generally
mounted to a plate such as the JACQUES MWM-3F.
Use Audio quality shielded pair cable for the audio signal from the
Microphone to the Controller.
Standard 3-pin XLR connectors attach the Microphone to the Controller’s
DB15 Connector.
continued…
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Web: http://www.jacques.com.au
268 Montague Road, West End,
Queensland, Brisbane, Australia 4101.
Email: [email protected]
4
268 Montague Rd, West End,
Brisbane, Australia, 4101
PCC-550M PC Master – Wiring Information
Monitor Speaker:
The Monitor Speaker is located on the Operator’s Console.
Low power Fig-8 Speaker cable is used to connect the external Monitor
Speaker to the Controller’s DB backshell connector, via an RCA
connector.
The RCA connector is attached to the DB15 backshell connector, either
as an inline or chassis socket, mounted on the DB Backshell.
PTT Switch:
There are two ways (2 OPTIONS) of wiring up the PTT switch.
OPTION 1:
The PTT Switch is located at the Operator’s Console. It is generally
mounted to a plate such as the JACQUES MWM-3F, which
connects the Microphone and PTT Switch.
The cable connects the PTT Switch to the Controller.
OPTION 2:
The PTT Switch is located by itself near the PCC-550M Master. It
directly connects back to the Master, not to the Controller.
Low power Fig-8 cable is used for as the preferred cable type.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Web: http://www.jacques.com.au
268 Montague Road, West End,
Queensland, Brisbane, Australia 4101.
Email: [email protected]
5
268 Montague Rd, West End,
Brisbane, Australia, 4101
PCC-550M PC Master – Wiring Information
Connections OPTION 1
(Figure 1).
Option 1 allows the Operator’s Console to contain the Microphone, PTT
Switch and Monitor Speaker, all are connected back to the Controller.
Only RS-232 data is
connected between the
Controller and the
Master.
Figure 1:
Connection diagram of
the PCC-550M Master,
using the OPTION 1
Master Cable.
Note:
For simplicity, the
Keyboard, Mouse and
Display Monitor are not
shown, but would also
be connected to the
PCC-550M PC Master.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Web: http://www.jacques.com.au
268 Montague Road, West End,
Queensland, Brisbane, Australia 4101.
Email: [email protected]
6
268 Montague Rd, West End,
Brisbane, Australia, 4101
PCC-550M PC Master – Wiring Information
Wiring Diagram OPTION 1
Figure 2 (next page) shows the wiring diagram of the JACQUES PCC550M Master cable, using OPTION 1.
This OPTION shows the PTT Switch connected directly to the Controller.
There is also a JACQUES MWM-3F plate, which is used to connect the
Microphone and PTT Switch.
There are three parts to the wiring of the PCC-550M Master cable:
PCC-550M Master:
This is the stand-alone PC, specially configured to run the proprietary
JACQUES Master Intercom Software.
It uses RS-232 data, connected directly to the JACQUES Controller,
allowing it to configure and control the Intercom System.
Controller:
The Controller is used to allow the distribution and connection of the
control data (RS-485) and Auxiliary Audio Channels to the rest of the
Intercom System.
The external Monitor Speaker, PTT Switch and Microphone are all
connected to the Controller’s DB15 connector.
Operator’s Console:
The Operator’s Console is the actual control desk where the Operator
sits to in front of the PCC-550M Master, able to use the PTT Switch,
Microphone and Monitor Speaker.
It is usually a crafted wooden desk, designed specifically for a particular
installation.
Although JACQUES doesn’t manufacture Operator’s desks as such,
there is a plate available (JACQUES MWM-3F) that accommodates a
Microphone and PTT Switch.
! The Microphone and Monitor Speaker are not required for a High-Level
Interface.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Web: http://www.jacques.com.au
268 Montague Road, West End,
Queensland, Brisbane, Australia 4101.
Email: [email protected]
7
268 Montague Rd, West End,
Brisbane, Australia, 4101
PCC-550M PC Master – Wiring Information
Figure 2:
Wiring Diagram OPTION 1
Connection wiring diagram of the PCC-550M Master to the Controller
and Operator’s desk.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Web: http://www.jacques.com.au
268 Montague Road, West End,
Queensland, Brisbane, Australia 4101.
Email: [email protected]
8
268 Montague Rd, West End,
Brisbane, Australia, 4101
PCC-550M PC Master – Wiring Information
Connections OPTION 2
(Figure 3).
Option 2 allows the Operator’s Console to contain the Microphone and
Monitor Speaker, but not the PTT Switch.
The Monitor Speaker and Microphone are connected to the Controller.
The PTT Switch is wired
directly to the COM Port
of the PCC-550M Master.
RS-232 data is connected
between the Controller
and the Master.
Figure 3:
Connection diagram of
the PCC-550M Master,
using the OPTION 2
Master Cable.
Note:
For simplicity, the
Keyboard, Mouse and
Display Monitor are not
shown, but would also be
connected to the PCC550M PC Master.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Web: http://www.jacques.com.au
268 Montague Road, West End,
Queensland, Brisbane, Australia 4101.
Email: [email protected]
9
268 Montague Rd, West End,
Brisbane, Australia, 4101
PCC-550M PC Master – Wiring Information
Wiring Diagram OPTION 2
Figure 4 (next page) shows the wiring diagram of the JACQUES PCC550M Master cable, using OPTION 2.
This OPTION shows the PTT Switch connected directly to the PCC550M Master.
There are three parts to the wiring of the PCC-550M Master cable:
PCC-550M Master:
This is the stand-alone PC, specially configured to run the proprietary
JACQUES Master Intercom Software.
It uses RS-232 data, connected directly to the JACQUES Controller,
allowing it to configure and control the Intercom System.
The PTT Switch is also connected directly to it, via a 10Kohm resistor.
Controller:
The Controller is used to allow the distribution and connection of the
control data (RS-485) and Auxiliary Audio Channels to the rest of the
Intercom System.
The external Monitor Speaker and Microphone are all connected to the
Controller’s DB15 connector.
Operator’s Console:
The Operator’s Console is the actual control desk where the Operator
sits to in front of the PCC-550M Master, able to use the Microphone and
Monitor Speaker.
It is usually a crafted wooden desk, designed specifically for a particular
installation.
! The Microphone and Monitor Speaker are not required for a High-Level
Interface.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Web: http://www.jacques.com.au
268 Montague Road, West End,
Queensland, Brisbane, Australia 4101.
Email: [email protected]
10
268 Montague Rd, West End,
Brisbane, Australia, 4101
PCC-550M PC Master – Wiring Information
Figure 4:
Wiring Diagram OPTION 2
Connection wiring diagram of the PCC-550M Master to the Controller
and Operator’s desk.
Note that the only difference from this to OPTION 1 is that the PTT
Switch has moved to be wired directly to the Master via a 10Kohm
resistor.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Web: http://www.jacques.com.au
268 Montague Road, West End,
Queensland, Brisbane, Australia 4101.
Email: [email protected]
11
268 Montague Rd, West End,
Brisbane, Australia, 4101
PCC-550M PC Master – Wiring Information
Wiring Table
The following Table 1 shows the cable wiring of the PCC-550M Master.
Table 1: Wiring of JACQUES PCC-550M Master
JACQUES Controller
Microphone
Monitor
Speaker
RS-232
PTT Switch
OPTION 1
PTT Switch
OPTION 2
JACQUES PCC-550M
Master
COM2
COM1
Port DB25 Port DB9
Pin#
Pin#
Operators
Console
DB15
Male
Pin#
DB15
Female
Pin#
XLR pin#3 (-ve)
XLR pin#2 (+ve)
XLR pin#1 (ground)
Fig-8, spkr(+ve)
Fig-8 spkr (-ve)
2
9
1
15
8
2
9
1
15
8
na
na
na
na
na
na
na
na
na
na
yes
yes
yes
yes
yes
Rx (Cat-5 Green)
Tx (Cat-5 Brown)
Ground. (use Cat-5
Brown/White and
Green/White)
Fig-8 cable
Fig-8 cable
13
11
13
11
3
2
2
3
no
no
14
14
7
5
no
10
3
10
3
na
na
na
na
yes
yes
Fig-8 cable
Fig-8 cable
na
na
na
na
5, via 10KΩ
4 and 20
8, via 10KΩ
7 and 4
no
no
Connect?
Other Information
! Refer to the separate Technical Manual PCC-550M PC Master
document, for specific Technical operations and Setup Tags.
! Refer to the separate Operating Manual PCC-550M PC Master
document, for specific User functions.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Web: http://www.jacques.com.au
268 Montague Road, West End,
Queensland, Brisbane, Australia 4101.
Email: [email protected]
12
268 Montague Rd, West End,
Brisbane, Australia, 4101
PCC-550M PC Master – Wiring Information
For further details about JACQUES Intercom features and designs,
please read the Architects and Engineers Specification ver 2002.
This document can be read from the website at: www.jacques.com.au
 copyright 2002 JACQUES ELECTRONICS Pty Ltd
Jacques Electronics Pty Ltd reserves the right to continually improve products by updating any
equipment specifications, document context and design styling and then passing this information onto
this document.
Phone: +61 7 3844 1103
Fax: +61 7 3844 1078
Web: http://www.jacques.com.au
268 Montague Road, West End,
Queensland, Brisbane, Australia 4101.
Email: [email protected]
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement