D-Link DWL-G680 Specifications

D-Link DWL-G680 Specifications
D-Link AirPremier®
DWL-G680
High-Speed 802.11g
Wireless Notebook Adapter
Manual
Rev. A2
Building Networks for People
Contents
Package Contents ............................................................................... 3
Introduction ........................................................................................... 4
Features & Benefits............................................................................. 5
Wireless Basics ................................................................................... 6
Getting Started ..................................................................................... 9
Using the Configuration Utility ............................................................. 12
Networking Basics ............................................................................. 26
Troubleshooting .................................................................................. 44
Technical Specifications ..................................................................... 51
Technical Support .............................................................................. 53
Warranty............................................................................................. 54
Registration ....................................................................................... 57
2
Package Contents
Contents of Package:
D-Link AirPremier® DWL-G680
High-Speed 2.4 GHz/802.11g Wireless Cardbus Adapter
Manual and Drivers on CD
Quick Installation Guide
If any of the above items are missing, please contact your reseller.
System Requirements:
A laptop or notebook computer with an available 32-bit Cardbus
slot
Windows XP/2000/ME/98SE
At least 64 MB of memory and a 500 MHz processor
An 802.11g or 802.11b Access Point (for Infrastructure mode), or another
802.11g or 802.11b wireless adapter (for Ad-Hoc, Peer-to-Peer networking
mode).
3
Introduction
The D-Link AirPremier® DWL-G680 Wireless Cardbus Adapter is an 802.11g highperformance, wireless adapter that supports high-powered wireless networking at home,
at work or in public places.
Unlike most network cards, the DWL-G680 provides data transfers at up to 108 Mbps.
The 802.11g standard is backwards compatible with 802.11b products.
The DWL-G680 has the newest, strongest, and most advanced security features available
today. When used with other 802.11 WPA/WPA2 (Wi-Fi Protected Access/Wi-Fi Protected
Access 2TM) and 802.1x compatible products in a network with a RADIUS server, the
security features include:
WPA/WPA2: Wi-Fi Protected Access/Wi-Fi Protected Access 2 TM which authorizes
and identifies users based on a secret key that changes automatically at regular
intervals. WPA/WPA2 uses TKIP (Temporal Key Integrity Protocol) to change
the temporal key every 10,000 packets (a packet is a kind of message transmitted
over a network.) This ensures much greater security than the standard WEP
security. (By contrast, the older WEP encryption required the keys to be changed
manually.)
802.1x: Authentication which is a first line of defense against intrusion. In the
authentication process, the Authentication Server* verifies the identity of the
client attempting to connect to the network. Unfamiliar clients would be denied
access.
For home users that will not incorporate a RADIUS server in their network, the security
for the DWL-G680, used in conjunction with other WPA/WPA2-compatible 802.11
products, will still be much stronger than ever before. Utilizing the Pre Shared Key
mode of WPA/WPA2, the DWL-G680 will obtain a new security key every time it connects
to the 802.11 network. You only need to input your encryption information once in the
configuration menu. No longer will you have to manually input a new WEP key frequently
to ensure security. With the DWL-G680, you will automatically receive a new key every
time you connect, vastly increasing the safety of your communication.
* Not all servers can provide Authentication.
4
Features & Benefits
Five times faster - achieve data transfer speeds up to 108 Mbps; up to 5x
faster than conventional 802.11b networks, when used with other 802.11g
devices
Fully compliant with the 802.11b standard and interoperable with all
existing 802.11b compliant and 802.11g compliant devices
Provides a simple and inexpensive way to connect your desktop computer to a wireless network at home, at the office, or in public places
Quick and Easy Installation- The DWL-G680 installs quickly and easily into a
standard Cardbus slot in a laptop computer. By following the simple steps outlined in the Quick Installation Guide, you can connect to an available wireless
network in a matter of seconds
32-bit Cardbus Performance/Plug & Play Connectivity - The powerful 32-bit
Cardbus interface utilized by the DWL-G680 ensures optional performance in
transmitting a wireless signal within the loptop computer. Pluy and play when
used with other D-Link AirPlus Xtreme G products will automatically connect to
network out of the box.
Operates in the 2.4GHz frequency range
Maximum reliability, throughput and connectivity with automatic data rate
switching
Supports Infrastructure networks via an access point and Peer-to-Peer
communication in Ad-Hoc mode
User-friendly configuration and diagnostic utilities
Provides a measure of security for the information transmitted over a
wireless network with high data encryption at 64-, 128-, and 152-bit WEP
Stronger Security than ever before with WPA/WPA2 - Wi-Fi Protected
Access/Wi-Fi Protected Access 2TM authorizes and identifies users based on
a secret key that changes automatically at regular intervals, for example:
TKIP (Temporal Key Integrity Protocol), in conjunction with a RADIUS
server, changes the temporal key every 10,000 packets, ensuring greater
security
Pre-Shared Key mode means that the home user, without a RADIUS
server, will obtain a new security key every time he or she connects to
the network, vastly improving the safety of communications on the network
Extra Protection - 802.1x Authentication in conjunction with the RADIUS
server verifies the identity of wireless clients wishing to gain access to the
WLAN
5
Wireless Basics
D-Link wireless products are based on industry standards to provide easy-to-use and
compatible high-speed wireless connectivity within your home, business or public access
wireless networks. D-Link wireless products will allow you access to the data you want,
when and where you want it. You will be able to enjoy the freedom that wireless networking
brings.
A Wireless Local Area Network (WLAN) is a computer network that transmits and receives
data with radio signals instead of wires. WLANs are used increasingly in both home and
office environments, and public areas such as airports, coffee shops and universities.
Innovative ways to utilize WLAN technology are helping people to work and communicate
more efficiently. Increased mobility and the absence of cabling and other fixed
infrastructure have proven to be beneficial for many users.
Wireless users can use the same applications they use on a wired network. Wireless
adapter cards used on laptop and desktop systems support the same protocols as
Ethernet adapter cards.
People use WLAN technology for many different purposes:
Mobility - Productivity increases when people have access to data in any location
within the operating range of the WLAN. Management decisions based on real-time
information can significantly improve worker efficiency.
Low Implementation Costs – WLANs are easy to set up, manage, change and
relocate. Networks that frequently change can benefit from WLANs ease of implementation.
WLANs can operate in locations where installation of wiring may be impractical.
Installation and Network Expansion - Installing a WLAN system can be fast
and easy and can eliminate the need to pull cable through walls and ceilings. Wireless
technology allows the network to go where wires cannot go - even outside the home or
office.
Scalability - WLANs can be configured in a variety of ways to meet the needs of
specific applications and installations. Configurations are easily changed and range
from peer-to-peer networks suitable for a small number of users to larger infrastructure
networks to accommodate hundreds or thousands of users, depending on the number of
wireless devices deployed.
Inexpensive Solution - Wireless network devices are as competitively priced as
conventional Ethernet network devices.
6
Wireless Basics (continued)
The DWL-G680 is compatible with 802.11g and 802.11b wireless products, which include:
D-Link Air DWL-650,D-Link AirPlus DWL-650+,
D-Link AirPremier® DWL-G550
2.4GHz Wireless Cardbus Adapter used with laptop computers
D-Link Air DWL-520, D-Link AirPlus DWL-520+
2.4GHz Wireless PCI cards used with desktop computers
TM
D-Link AirPlus DWL-900AP+, D-Link AirPlus Xtreme G DWL-2100AP
2.4GHz Wireless Access Points
D-Link AirPlus DI-614+, DI-714P+
2.4GHz Wireless Routers
Standards-Based Technology
The DWL-G680 Wireless Cardbus Adapter utilizes the new 802.11g standard.
The IEEE 802.11g standard is an extension of the 802.11b standard. It increases the
data rate up to 54 Mbps within the 2.4GHz band, utilizing OFDM technology.
This means that in most environments, within the specified range of this device, you will
be able to transfer large files quickly or even watch a movie in MPEG format over your
network without noticeable delays. This technology works by transmitting high-speed
digital data over a radio wave utilizing OFDM (Orthogonal Frequency Division Multiplexing)
technology. OFDM works by splitting the radio signal into multiple smaller sub-signals
that are then transmitted simultaneously at different frequencies to the receiver. OFDM
reduces the amount of crosstalk (interference) in signal transmissions. The D-Link DWLG680 will automatically sense the best possible connection speed to ensure the greatest
speed and range possible.
802.11g offers the most advanced network security features available today, including:
WPA/WPA2 , 802.1x, TKIP, AES and Pre-Shared Key mode. These security features
are explained in more detail in the Introduction and the Features section of this manual.
The DWL-G680 is backwards compatible with 802.11b devices. This means that if you
have an existing 802.11b network, the devices in that network will be compatible with
802.11g devices at speeds up to 11Mbps in the 2.4GHz range.
7
Wireless Basics (continued)
Installation Considerations
The D-Link AirPremier® DWL-G680 lets you access your network using a wireless
connection from virtually anywhere within its operating range. Keep in mind, however,
that the number, thickness and location of walls, ceilings, or other objects that the
wireless signals must pass through, may limit the range. Typical ranges vary depending
on the types of materials and background RF (radio frequency) noise in your home or
business. The key to maximizing wireless range is to follow these basic guidelines:
1 Keep the number of walls and ceilings between the DWL-G680 and other network
devices to a minimum - each wall or ceiling can reduce your DWL-G680
range from 3-90 feet (1-30 meters.) Position your devices so that the number of
walls or ceilings is minimized.
2 Be aware of the direct line between network devices. A wall that is 1.5 feet thick
(.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At
a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so
that the signal will travel straight through a wall or ceiling (instead of at an
angle) for better reception.
3 Building materials can impede the wireless signal - a solid metal door or aluminum
studs may have a negative effect on range. Try to position wireless devices and
computers with wireless adapters so that the signal passes through drywall or
open doorways and not other materials.
4 Keep your product away (at least 3-6 feet or 1-2 meters) from electrical
devices or appliances that generate RF noise.
8
Getting Started
With its default settings, the DWL-G680, when activated, will connect
with other D-Link AirPremier® products, right out of the box.
There are basically two modes of networking:
Infrastructure - using an Access Point or Router, such as
the DI-624
Ad-Hoc - directly connecting to another computer, for peer-topeer communication, using wireless network adapters on
each computer, such as two or more DWL-G680 wireless
network adapters
On the following pages we will show you an example of an Infrastructure Network
and an Ad-Hoc Network.
An Infrastructure network contains an Access Point or Router. The Infrastructure
Network example shown on the following page contains the following D-Link network
devices (your existing network may be comprised of other devices):
A wireless Router - D-Link AirPlus Xtreme G
A laptop computer with a wireless adapter D-Link AirPremier® DWL-G680, D-Link AirPlus Xtreme G
DWL-G650, or D-Link AirPlus DWL-G630
A Cable modem - D-Link DCM-201
®
DI-624
LEDs
LED stands for Light-Emitting Diode.
Activity:
A blinking light indicates data is being transmitted
Link:
A steady light indicates a connection to an access point
9
Getting Started (continued)
Setting up a Wireless Infrastructure Network
1
2
3
7
4
DWL-G550
6
DWL-G680
5
Please remember that D-Link AirPremier® wireless devices are
pre-configured to connect together, right out of the box, with their default settings.
For a typical wireless setup at home (as shown above), please do the following:
You will need broadband Internet access (a Cable or DSL-subscriber line into
your home or office).
Consult with your Cable or DSL provider for proper installation of the modem.
Connect the Cable or DSL modem to your broadband router (see the Quick
Installation Guide included with your router.)
If you are connecting a desktop computer to your networks, you can install the
D-Link AirPremier® DWL-G550 Wireless Cardbus Adapter into a computer. (See
the Quick Installation Guide included with the DWL-G550.)
Install the D-Link AirPremier® DWL-G680 Wireless Cardbus Adapter into a laptop
computer.
(See the Quick Installation Guide included with the DWL-G680.)
If you wish, you may connect a computer that is equipped with an Ethernet
network adapter (such as a DFE-530TX+) to the router also.
A RADIUS Server is optional. Connect a RADIUS Server to your network to use
all the features of WPA/WPA2. (Without a RADIUS Server you can still use the
WPA/WPA2 Pre-Shared Key mode.) RADIUS Authentication can also be
provided by another service provider over the Internet and remote to your network
site.
10
Getting Started (continued)
Setting up a Wireless Ad Hoc Network
Desktop
D-Link AirPremier®
DWL-G550
D-Link AirPremier®
DWL-G680
Install the DWL-G550 into the desktop computer.
(See the Quick Installation Guide included with the product for
installation instructions.)
Install the DWL-G680 Wireless PC Card Adapter into a laptop computer.
(See the Quick Installation Guide included with the product.)
Set the wireless configuration for the adapters to Ad-Hoc mode, set the
adapters to the same channel, and assign an IP Address to each
computer on the Ad-Hoc network. (See Box below).
IP Address
When assigning IP Addresses to the computers on the network, please remember
that the IP Address for each computer must be in the same IP Address range
as all the computers in the network, and the subnet mask must be exactly the
same for all the computers in the network.
For example: If the first computer is assigned an IP Address of 192.168.0.2 with a
Subnet Mask of 255.255.255.0, then the second computer can be assigned an IP
Address of 192.168.0.3 with a Subnet Mask of 255.255.255.0, etc.
IMPORTANT: If computers or other devices are assigned the same IP Address,
one or more of the devices may not be visible on the network.
11
Using the Configuration Utility
D-Link AirPremier® DWL-G680 uses the Configuration Utility as the management
software. The utility provides the user an easy interface to change any settings related to
the wireless adapter. After you have completed the installation of the DWL-G680 (refer to
the Quick Installation Guide that came with your purchase) whenever you start the
computer, the Configuration Utility starts automatically and the system tray icon is
loaded in the toolbar (see illustration below*.) Clicking on the utility icon will start the
Configuration Utility. Another way to start the Configuration Utility is to click on
Start>Programs>D-Link AirPremier >D-Link AirPremier Client Utility.
If you are using Windows XP, you can use either the Zero Configuration Utility or the
D-Link Configuration Utility.
To use the D-Link Configuration Utility with XP, right-click
on the Wireless network icon in the taskbar in the lower
right-hand corner of your computer screen.
In the window that appears, select View
Available Wireless Networks and click
the Advanced button. The screen at right
will appear.
Select the Wireless Networks tab.
Uncheck the box in the properties window
that enables windows configuration.
After you have done this, you can then use the D-Link
Configuration Utility with XP by clicking on the D-Link
Configuration Utility icon.
*Configuration Utility icon
in the system tray
If the icon does not display in the taskbar, then click on
this icon on your desktop to open.
12
Using the Configuration Utility (continued)
After clicking on the Configuration Utility icon, the Link Info screen will display the
settings for the DWL-G680:
Status:
Link Info
Displays the MAC Address of the
Access Point or Router to which the
DWL-G680 is associated
SSID:
The Service Set Identifier is the name
assigned to the wireless network.
The factory SSID setting is default.
Frequency:
802.11g indicates that the DWLG680 is communicating in the
2.4GHz band.
Wireless Mode:
Either Infrastructure or Ad-Hoc will be displayed here. (Please see the Getting
Started section in this manual for an explanation of these two modes.)
Encryption:
You can see if WEP (Wired Equivalent Privacy) is Enabled or Disabled here.
Tx Rate:
Tx Rate settings are automatically determined for an optimal speed up to a maximum
of 54Mbps.
Channel:
The channel selection is automatically determined by the DWL-G680.
Signal Strength:
Displays the Link Quality for the DWL-G680 wireless connection to the Access Point.
The Signal Strength represents the wireless signal between the Access Point and the
DWL-G680. The percentage coincides with the graphical bar.
Packet Count:
Displays the statistics of the data packets that are transmitted and received.
Rescan Button:
Rescans for the strongest signal in your environment and associates with that Access
Point or Router.
13
Using the Configuration Utility (continued)
Configuration
After you have configured
the network through the
Site Survey section of
the D-Link AirPremier
Utility, you can make
minor adjustments and
check on settings in this
Configuration screen.
For a complete
explanation of the
configuration of a
network, please refer
to the Site Survey
section in this
chapter.
SSID:
Service Set Identifier is a name that identifies a wireless network. Access Points and
wireless devices attempting to connect to a specific WLAN (Wireless Local Area Network)
must use the same SSID. The default setting is default.
Wireless Mode:
Click on the pull-down menu; select from the following options:
Infrastructure - connecting to the WLAN using an Access Point. (This is the default
setting).
Ad-Hoc - wireless mode used when connecting directly to a computer equipped
with a wireless adapter in a peer-to-peer environment.
Data Encryption:
Select Enabled or Disabled.
Authentication:
Choose one of the following modes:
Open Authentication - the DWL-G680 is visible to all devices on the network
Shared Authentication - allows communication only with other devices with
identical WEP settings
WPA/WPA2 - Wi-Fi Protected Access/Wi-Fi Protected Access 2 TM which
authorizes and identifies users based on a secret key that changes automatically
at a regular interval. (A RADIUS Server is required for this mode.)
WPA-PSK/WPA2-PSK - WPA/WPA2 Pre-Shared Key mode ensures that the DWLG680 will obtain a new security key every time it connects to the 802.11 network.
(A RADIUS Server is not required for this mode.)
14
Using the Configuration Utility (continued)
Key Length:
Select the key length and either ASCII or hexadecimal format.
IEEE 802.1x:
Authentication which is a first line of defense against intrusion. In the Authentication
process the Authentication Server* verifies the identity of the client attempting to connect to the network. Unfamiliar clients are denied access.
Keys 1-4:
Select the default key
Hexadecimal digits consist of the numbers 0-9 and the letters A-F
ASCII (American Standard Code for Information Interchange) is a code for
representing English letters as numbers from 0-127
IP Settings
When you click IP Settings in the
Configuration window, this pop-up
screen will appear. Configure the IP
Settings in this window.
Click Apply to save changes.
*Not all servers can provide Authentication
15
Using the Configuration Utility (continued)
Frequency:
Select the Frequency
Starting Ad-Hoc Network:
Select the Ad-Hoc Network
Ad-Hoc Channel:
All devices in the Ad-Hoc network must be set to the same channel
Profile IP Settings:
You can Enable or Disable
the IP Settings portion of your
profile here. If you select
Disable you will need to
configure the IP Address
information each time you
connect to a network. If you
select Enable you will
maintain the same IP Address
information each time you
connect to a network.
Advanced
Power Mode:
Disable -this default setting
consumes the most power
Enable - this setting
consumes the least power.
Launch Utility on Startup:
Select Enable or Disable
Data Packet Parameter:
Set the Fragmentation Threshold and the RTS Threshold. Please see below.
Fragmentation Threshold:
This value should remain at its default setting of 2432. If you experience a high packet
error rate, you may slightly increase your Fragmentation Threshold within the value
range of 256 to 2432. Setting the Fragmentation Threshold too low may result in poor
performance.
RTS Threshold:
This value should remain at its default setting of 2432. If inconsistent data flow is a
problem, only a minor modification should be made.
Click Apply if you have made any changes
16
Using the Configuration Utility (continued)
Available Network:
The top section of the window displays the Available Networks. Scroll up and down the
list and highlight the network to which you wish to connect. Click on the Connect button.
Profile:
In the lower half of the screen, you can manage the profiles that you have created for the
wireless network at home, at the office and in public places. Scroll up and down and
highlight the profile that you wish to configure. You can Add or Remove a profile, or
configure the Properties of the profile in order to connect with an available network.
Refresh:
Site Survey
Click on Refresh to get the
most updated list of available
networks.
Configure:
Highlight an existing network
and click Configure; the
configuration window on the
next page will appear.
Advanced:
Highlight a network; click
Advanced and the screen on
the next page will appear.
Add:
Click Add and the screen on the next page will appear.
Remove:
Highlight a network profile; click Remove to remove a network from the profile list.
Properties:
Highlight a network profile; click Properties and the screen on the next page will appear.
Connect:
Highlight a network profile; click Connect to connect to that network.
Rescan:
Click Rescan to rescan and connect to the strongest signal.
17
Using the Configuration Utility (continued)
Site Survey > Add
Advanced
In this window you can select
the type of network connection.
Click OK to save the
changes.
If you clicked on Add, you can
configure, in this window, all the
properties of a profile that you
wish to add to the network.
Configuration, Add or Properties
If you clicked on Configuration
or Properties you can configure, in this window, all the properties of a profile that already
exists in the network.
If you select WPA/WPA2 in
the Authentication field, please
see detailed instructions for
configuring WPA/WPA on the
following pages.
If you choose to use the IEEE
802.1x feature, please see the
detailed instructions on the following pages.
Click OK to save the
changes.
18
Using the Configuration Utility (continued)
Site Survey > Configuration > 802.1x
To use 802.1x and to configure its settings, please do the following:
IEEE 802.1x Select Enabled.
Click Authentication Config.
Advanced Security Settings
Select the EAP Type you
want to use. Configure the
information needed for
authenticating.
Inner Authentication Protocol.
For an explanation of
the terms shown in this
window please see the
following pages.
Trusted CA List.
Click OK
19
Using the Configuration Utility (continued)
802.1x > Advanced Security Settings > EAP Types
EAP Type
Inner Authentication
Protocol
Information needed
for Authenticating
EAP-TLS
Certificate
User Name
EAPMSCHAPv2
User Name
Password
Domain Name
LEAP
User Name
Password
EAP-TTLS
PAP
TTLS Identity
User Name
Password
CHAP
TTLS Identity
User Name
Password
MSCHAP
TTLS Identity
User Name
Password
Domain Name
MSCHAPv2
TTLS Identity
User Name
Password
Domain Name
20
Using the Configuration Utility (continued)
802.1x > Advanced Security Settings > EAP Types (continued)
EAP Type
EAP-TTLS
Inner Authentication
Protocol
Information needed
for Authenticating
EAP-MD5
TTLS Identity
User Name
Password
EAPGeneric Token card
TTLS Identity
User Name
Password
EAP-MSCHAPv2
TTLS Identity
User Name
Password
Domain Name
EAP-MD5
User Name
Password
EAP-MSCHAPv2
User Name
Password
Domain Name
EAPGeneric Token card
User Name
Password
PEAP
802.1x > Advanced Security Settings > Definitions of Terms
Validate Server Certificate:
Check Validate Server Certificate to verify the identity of the authentication server
based on its certificate when using EAP-TTLS, PEAP, and EAP-TLS. (This is
checked by default.)
Certain protocols, such as EAP-TTLS, PEAP, and EAP-TLS, allow you to verify the
identity of the authentication server as the server verifies your identity. This is called
mutual authentication.
You can select trusted authentication server certificates using the Add button at the
Trusted CA List (at the bottom of the Advanced Security Settings page).
21
Using the Configuration Utility (continued)
802.1x > Advanced Security Settings > Definitions of Terms (continued)
Domain Name:
Each server has a domain name that uniquely identifies it. That domain name is normally
contained in the Subject CN field of the server certificate. A server domain name ends
with the name of a larger administrative domain, to which the server belongs.
TTLS Identity:
Tunneled Transport Layer Security satisfies a requirement for strong encryption and
mutual authentication on Wireless networks. EAP-TTLS has a unique feature that other
protocols do not offer. Because it sets up an encrypted tunnel for your credentials, it is
also able to pass your login name through that tunnel. That means that not only are your
credentials secure from eavesdropping, but your identity is protected as well. Thus, with
EAP-TTLS you have two identities: an inner one, and an outer one. The inner identity is
your actual user name. Your outer identity can be completely anonymous. Set your
outer identity in the TTLS Identity field.
Trusted CA List:
The Trusted CA List allows you to configure which authentication servers you trust for
the purpose of logging you in to the network.
Click Add at the Trusted CA List at the bottom of the Advanced Security Settings page.
Select the Trusted CA that you want to add and click OK.
Select the Trust CA:
22
Using the Configuration Utility (continued)
Authentication > WPA/WPA2
Select the available
network to which you
want to connect.
Click Configure.
Select WPA/WPA2 in
the Authentication
field.
Click Authentication
Config
After you click Authentication Config, the Advanced Security Settings screen will appear. Complete the Advanced Security Settings configuration. Please see pages 19-22 of
this manual to find out more about the Advanced Security Settings.
23
Using the Configuration Utility (continued)
Authentication > WPA-PSK/WPA2-PSK
Select the available
network to which you
want to connect.
Click Configure.
WPA-PSK/
WPA2-PSK
does not require a
RADIUS Server in the
network.
Select WPA-PSK/
WPA2-PSK in the
Authentication field.
Click Authentication
Config
24
Using the Configuration Utility (continued)
Authentication > WPA-PSK/WPA2-PSK (continued)
Advanced Security Settings
Enter the WPA/WPA2
Passphrase.
Click OK.
The configuration is done.
25
Networking Basics
Using the Network Setup Wizard in Windows XP
In this section you will learn how to establish a network at home or work, using
Microsoft Windows XP.
Note: Please refer to websites such as http://www.homenethelp.com
and http://www.microsoft.com/windows2000 for information about networking
computers using Windows 2000.
Go to Start>Control Panel>Network Connections
Select Set up a home or small office network
When this screen appears, click Next.
26
Networking Basics (continued)
Please follow all the instructions in this window:
Click Next
In the following window, select the best description of your computer. If your
computer connects to the Internet through a gateway/router, select the second option
as shown.
Click Next
27
Networking Basics (continued)
Enter a Computer description and a Computer name (optional.)
Click Next
Enter a Workgroup name. All computers on your network should have the same
Workgroup name.
Click Next
28
Networking Basics (continued)
Please wait while the Network Setup Wizard applies the changes.
When the changes are complete, click Next.
Please wait while the Network Setup Wizard configures the computer.
This may take a few minutes.
29
Networking Basics (continued)
In the window below, select the option that fits your needs. In this example, Create a
Network Setup Disk has been selected. You will run this disk on each of the
computers on your network. Click Next.
Insert a disk into the Floppy Disk Drive, in this case drive A.
30
Networking Basics (continued)
Please read the information under Here thow in the screen below. After you complete
the Network Setup Wizard you will use the Network Setup Disk to run the Network
Setup Wizard once on each of the computers on your network. To continue click Next.
31
Networking Basics (continued)
Please read the information on this screen, then click Finish to complete the
Network Setup Wizard.
The new settings will take effect when you restart the computer. Click Yes to restart
the computer.
You have completed configuring this computer. Next, you will need to run the Network
Setup Disk on all the other computers on your network. After running the Network
Setup Disk on all your computers, your new wireless network will be ready to use.
32
Networking Basics (continued)
Naming Your Computer in Windows Vista below dereetions
To name your computer in Windows VISTA, please follow these directions:
„Click
Start (in the lower left corner of the screen).
„Right-click on Computer.
„Select Properties.
33
%NKEM
VJG #FXCPEGF U[UVGO
„
setting
Select
„
the Computer Name
TabKPVJG5[UVGO2TQRGTVKGU
window.
;QWOC[GPVGTCComputer
„
DescriptionKH[QWYKUJVJKU
ſGNFKUQRVKQPCN
To rename
the computer
„
and join a domain, click
Change.
34
Networking Basics (continued)
Naming Your Computer
In this window, enter the
„
Computer name.
„Enter the name of the
Workgroup.
„#NN EQORWVGTU QP [QWT
network must have
the same Workgroup
name.
Click OK.
„
Checking the IP Address
In Windows XP
„ Right-click on
the Local Area
Connection icon in
the task bar.
„ Click on Status.
35
Networking Basics (continued)
Checking the IP Address in Windows XP
This window will appear.
„ Click the Support
tab.
„ Click Close.
Checking the IP Address
In Windows VISTA
„ Right-click on the
Wireless Network
Connection icon in
the task bar.
„ Click on Network
and Sharing
Center.
36
Networking Basics (continued)
Checking the IP Address
In Windows Vista
This window will appear.
„ Click the View
Status.
„ Click on the
Detail.
„ Click Close.
37
Networking Basics (continued)
Assigning a Static IP Address
Note: Many broadband routers will automatically assign IP addresses to the
computers on the network, using DHCP (Dynamic Host Configuration Protocol)
technology. If you are using a DHCP-capable router you will not need to assign
static IP addresses.
+H[QWCTGPQVWUKPIC&*%2ECRCDNGTQWVGTQT[QWPGGFVQCUUKIPCUVCVKE+2
address, please follow these instructions:
In Windows XP/ 2000
„ Go
to Start.
„ Click
on
Control Panel.
on Network
„Double-click
Connections.
38
Networking Basics (continued)
on Local Area
„Right-click
Connections.
„Click
on Properties.
„Click on Internet
Protocol (TCP/IP).
„Click Properties.
D-Link AirPlus® G DWL-G122 Wireless USB Adapter
39
Networking Basics (continued)
„
Input your IP address and
subnet mask. (The IP
addresses on your network
must be within the same
range. For example, if
one computer has an IP
address of 192.168.0.2,
the other computers should
have IP addresses that are
sequential, like 192.168.0.3
and 192.168.0.4. The subnet
mask must be the same for
all the computers on the
network.)
„ Input your DNS server
addresses. (Note: If you
are entering a DNS server,
you must enter the IP
address of the Default
Gateway.)
The DNS server information will be supplied by your ISP (Internet Service
Provider.)
„
Click OK.
40
Networking Basics (continued)
In Windows VISTA
„ Right
Click on
Wireless Network
Connection icon
in the task bar
„ Click
Network
and Sharing
Center
„ Click
on View Status .
„ Click
on Properties .
41
Networking Basics (continued)
Assigning a Static IP Address
„Click on Internet
Protocol (TCP/IPv4).
„Click Properties.
D-Link AirPlus® G DWL-G122 Wireless USB Adapter
„ +PRWV[QWTIP address and
subnet mask. 6JG +2
CFFTGUUGUQP[QWTPGVYQTM
must be within the same
range. For example, if
one computer has an IP
address of 192.168.0.2,
the other computers should
have IP addresses that are
sequential, like 192.168.0.3
and 192.168.0.4. The
subnet mask must be the
same for all the computers
QPVJGPGVYQTM
„+PRWV[QWT&05UGTXGT
CFFTGUUGU
0QVG+H[QWCTG
GPVGTKPIC&05UGTXGT[QW
must enter the IP address of
VJG&GHCWNV)CVGYC[
The DNS server information will be
supplied by your ISP (Internet Service
Provider.)
„Click OK.
42
Networking Basics (continued)
Checking the Wireless Connection
by Pinging in Windows XP and 2000*
Ŷ
Go to Start > Run >
type cmd. A window
similar to this one
will appear. Type
ping
xxx.xxx.xxx.xxx,
where xxx is the IP
Address of the
Wireless Router or
Access Point. A
good wireless
connection will show
four replies from the
Wireless Router or
Access Point, as
shown.
Checking the Wireless Connection
by Pinging in Windows VISTA
Ŷ
Go to Start > Start
Searcg > type cmd.
A window similar to
this one will appear.
Type ping
xxx.xxx.xxx.xxx,
where xxx is the IP
Address of the
Wireless Router or
Access Point. A
good wireless
connection will
show four replies
from the wireless
Router or Access
point, as shown.
*You may be pinging different IP Addresses than the ones pictured here, however the
procedure for pinging remains the same.)
43
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and
operation of the DWL-G680. Read the following descriptions if you are having problems.
(The examples below are illustrated in Windows Vista / Windows XP. If you have another
operating system, these solutions will still apply although the appearance on your
computer screen may differ.)
1. Check that the drivers for the DWL-G680 are installed properly.
In Windows XP
Ŷ
Go to Start > My
Computer >
Properties
Ŷ
Select the
Hardware
Tab
Ŷ
Click Device
Manager
44
Troubleshooting (continued)
Double-click
on Network
Adapters
Right-click on D-Link
AirPremier® DWL-G680
Wireless Cardbus
Adapter
Select Properties
to check that the
drivers are
installed properly
Look under Device
Status to check that the
device is working
properly
Click OK
45
Troubleshooting (continued)
In Windows VISTA
„ Go to Start >
Computer >
Properties.
„ClickDevice
Manager.
46
Troubleshooting (continued)
„Double-click
on
Network Adapters.
on
„Right-click
D-Link AirPlus® G
DWL-G122 Wireless
USB Adapter.
„Select
Properties to
check that the drivers
CTGKPUVCNNGFRTQRGTN[
D-Link AirPlus® G DWL-G122 Wireless USB Adapter
„Look
under Device
Status to check that
the device is working
RTQRGTN[
„ClickOK.
47
Troubleshooting (continued)
2. I cannot connect to the Access Point or the Wireless Router.
Make sure that the SSID on the DWL-G680 Wireless Cardbus Adapter is
exactly the same as the SSID on the Access Point or Wireless Router.
Move the DWL-G680 and Access Point or Wireless Router into the same
room and then test the wireless connection.
Disable all security settings. (WEP, MAC Address Control, AES)
Refresh the DWL-G680 Utility
Turn off your Access Point and the computer with the DWL-G680. Turn
on the Access Point, and then turn on the computer with the DWL-G680.
3. The DWL-G680 Activity and Link lights are not on.
Check to see if the DWL-G680 Cardbus adapter is firmly inserted into the
Cardbus slot of your computer.
4. I forgot my Encryption key.
Reset the Access Point to its factory default settings and restore the DWLG680 Wireless Cardbus Adapter to the factory default settings. (The default
settings are listed in the Using the Configuration Utility section in this
manual.)
5. The computer does not recognize the DWL-G680 Wireless Cardbus
Adapter.
Make sure that the DWL-G680 Wireless Cardbus Adapter is properly seated
in the computer Cardbus slot.
If Windows does not detect the hardware upon insertion of the adapter,
make sure to completely remove drivers that were previously loaded. To
remove the drivers, do the following:
48
Troubleshooting (continued)
A. Under Tools> select Folder Options- select View > under
Hidden files and folders > select Show hidden files and
folders
B. Uncheck Hide extension for known file types > click on
Apply
C. Search for the files DWLG680.INF and DWLG680.SYS. Remove
these files from the INF and SYSTEM32 (DRIVERS) folders in
the Windows directory. Note: Windows XP and Windows 2000
will rename .inf files that have not received WHQL certification
into oem.inf files (e.g., oem1.inf.)
6. The computer with the DWL-G680 installed is unable to connect to
the wireless network and/or the Internet.
Check that the LED indicators for the broadband modem are indicating
normal activity. If not, there may be a problem with the broadband connection.
Check that the LED indicators on the wireless router are functioning properly.
If not, check that the AC power and Ethernet cables are firmly connected.
Check that the IP Address, subnet mask, gateway, and DNS settings are
correctly entered for the network
In Infrastructure mode, make sure the same Service Set Identifier (SSID)
is specified on the settings for the wireless clients and Access Points. The
SSID factory default setting for the D-Link AirPremier® products is default.
(Double-click on the WLAN icon in the taskbar. The Link Info screen will
display the SSID setting.)
In Ad-Hoc mode, both wireless clients will need to have the same SSID.
Please note that it might be necessary to set up one client to establish a
BSS (Basic Service Set) and wait briefly before setting up other clients.
This prevents several clients from trying to establish a BSS at the same
time, which can result in multiple singular BSSs being established, rather
than a single BSS with multiple clients associated to it.
49
Troubleshooting (continued)
A. Under Tools> select Folder Options- select View > under
Hidden files and folders > select Show hidden files and
folders
B. Uncheck Hide extension for known file types > click on
Apply
C. Search for the files DWLG680.INF and DWLG680.SYS. Remove
these files from the INF and SYSTEM32 (DRIVERS) folders in
the Windows directory. Note: Windows XP and Windows 2000
will rename .inf files that have not received WHQL certification
into oem.inf files (e.g., oem1.inf.)
6. The computer with the DWL-G680 installed is unable to connect to
the wireless network and/or the Internet.
Check that the LED indicators for the broadband modem are indicating
normal activity. If not, there may be a problem with the broadband connection.
Check that the LED indicators on the wireless router are functioning properly.
If not, check that the AC power and Ethernet cables are firmly connected.
Check that the IP Address, subnet mask, gateway, and DNS settings are
correctly entered for the network
In Infrastructure mode, make sure the same Service Set Identifier (SSID)
is specified on the settings for the wireless clients and Access Points. The
SSID factory default setting for the D-Link AirPremier® products is default.
(Double-click on the WLAN icon in the taskbar. The Link Info screen will
display the SSID setting.)
In Ad-Hoc mode, both wireless clients will need to have the same SSID.
Please note that it might be necessary to set up one client to establish a
BSS (Basic Service Set) and wait briefly before setting up other clients.
This prevents several clients from trying to establish a BSS at the same
time, which can result in multiple singular BSSs being established, rather
than a single BSS with multiple clients associated to it.
50
Technical Specifications
Standards
IEEE 802.11g
IEEE 802.11b
Bus Type:
32-bit Cardbus
Data Rates:
108, 54, 48, 36, 24, 18, 12, 11, 9, 6, 5.5, 2 and 1Mbps
Security:
802.1x
WPA/WPA2 (Wi-Fi Protected Access/Wi-Fi Protected Access
2TM), 64-,128-bit WEP with TKIP, MIC, IV Expansion, Shared Key
Authentication
Power Consumption:
PowerSave mode = 30mA
Receive mode = 300mA
Transmit mode = 500mA
Wireless Trasmit Power:
802.11b
Typical 21dBm at 11, 5.5, 2 and 1Mbps
802.11g
Typical +15 - 18dBm for 54Mbps
Typical +16 - 19dBm for 48Mbps
Typical +17 - 20dBm for 36Mbps
Typical +18 - 21dBm for 24, 18, 12, 9, 6Mbps
Internal Antenna Type:
Diversity
51
Technical Specifications
Temperature
Operating: 0°C to 55°C (32°F to 149°F)
Humidity:
10% - 90%, RH, non-condensing
Receiver Sensitivity:
802.11b
DQPSK
DBPSK
DSSS
CCK
802.11g
BPSK
QPSK
6QAM
OFDM
Physical Dimensions:
L = 4.68 inches (118mm)
W = 2.13 inches (54mm)
H = 0.28 inches (7.1mm)
Weight:
0.088 lb. (39.91 grams)
52
Technical Support
You can find software updates and user documentation on the D-Link website.
D-Link provides free technical support for customers within the United States and
within Canada for the duration of the warranty period on this product.
U.S. and Canadian customers can contact D-Link technical support through our
website, or by phone.
Tech Support for customers within the United States:
D-Link Technical Support over the Telephone:
(877) 453-5465
Monday through Friday 8:00am to 5:00pm (PST).
D-Link Technical Support over the Internet:
http://support.dlink.com
email:[email protected]
Tech Support for customers within Canada:
D-Link Technical Support over the Telephone:
(800) 361-5265
Monday to Friday 7:30am to 12:00pm EST
D-Link Technical Support over the Internet:
http://support.dlink.ca
email:[email protected]
53
Warranty
(USA only)
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. ( E-Link? provides this Limited
warranty for its product only to the person or entity that originally purchased the product from:
•
•
D-Link or its authorized reseller or distributor and
Products purchased and delivered within the fifty states of the United States, the District of
Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, addresses with an
APO or FPO.
Limited Warranty: D-Link warrants that the hardware portion of the D-Link products described
below will be free from material defects in workmanship and materials from the date of original retail
purchase of the product, for the period set forth below applicable to the product type ( X arranty
Period? , except as otherwise stated herein.
3-Year Limited Warranty for the Product(s) is defined as follows:
•
•
•
Hardware (excluding power supplies and fans) Three (3) Years
Power Supplies and Fans One (1) Year
Spare parts and spare kits Ninety (90) days
D-Link tsole obligation shall be to repair or replace the defective Hardware during the Warranty Period
at no charge to the original owner or to refund at D-Link tsole discretion. Such repair or replacement will
be rendered by D-Link at an Authorized D-Link Service Office. The replacement Hardware need not be
new or have an identical make, model or part. D-Link may in its sole discretion replace the defective
Hardware (or any part thereof) with any reconditioned product that D-Link reasonably determines is
substantially equivalent (or superior) in all material respects to the defective Hardware. Repaired or
replacement Hardware will be warranted for the remainder of the original Warranty Period from the date
of original retail purchase. If a material defect is incapable of correction, or if D-Link determines in its sole
discretion that it is not practical to repair or replace the defective Hardware, the price paid by the original
purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective
Hardware. All Hardware (or part thereof) that is replaced by D-Link, or for which the purchase price is
refunded, shall become the property of D-Link upon replacement or refund.
Limited Software Warranty: D-Link warrants that the software portion of the product ( Toftware?
will substantially conform to D-Link tthen current functional specifications for the Software, as set forth
in the applicable documentation, from the date of original retail purchase of the Software for a period of
ninety (90) days ( Xarranty Period? , provided that the Software is properly installed on approved
hardware and operated as contemplated in its documentation. D-Link further warrants that, during the
Warranty Period, the magnetic media on which D-Link delivers the Software will be free of physical
defects. D-Link tsole obligation shall be to replace the non-conforming Software (or defective media)
with software that substantially conforms to D-Link tfunctional specifications for the Software or to
refund at D-Link tsole discretion. Except as otherwise agreed by D-Link in writing, the replacement
Software is provided only to the original licensee, and is subject to the terms and conditions of the
license granted by D-Link for the Software. Software will be warranted for the remainder of the original
Warranty Period from the date or original retail purchase. If a material non-conformance is incapable of
correction, or if D-Link determines in its sole discretion that it is not practical to replace the nonconforming Software, the price paid by the original licensee for the non-conforming Software will be
refunded by D-Link; provided that the non-conforming Software (and all copies thereof) is first returned
to D-Link. The license granted respecting any Software for which a refund is given automatically
terminates.
Non-Applicability of Warranty: The Limited Warranty provided hereunder for hardware and software
of D-Link tproducts will not be applied to and does not cover any refurbished product and any product
purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers,
or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case,
the product is being sold Bs-Is? without any warranty whatsoever including, without limitation, the
Limited Warranty as described herein, notwithstanding anything stated herein to the contrary.
Submitting A Claim: The customer shall return the product to the original purchase point based on its
return policy. In case the return policy period has expired and the product is within warranty, the
customer shall submit a claim to D-Link as outlined below:
54
•
The customer must submit with the product as part of the claim a written description of the
Hardware defect or Software nonconformance in sufficient detail to allow D-Link to confirm
the same.
•
The original product owner must obtain a Return Material Authorization ( SMA? number from
the Authorized D-Link Service Office and, if requested, provide written proof of purchase of
the product (such as a copy of the dated purchase invoice for the product) before the
warranty service is provided.
•
After an RMA number is issued, the defective product must be packaged securely in the
original or other suitable shipping package to ensure that it will not be damaged in transit, and
the RMA number must be prominently marked on the outside of the package. Do not include any
manuals or accessories in the shipping package. D-Link will only replace the defective portion
of the Product and will not ship back any accessories.
•
The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery
( DOD? is allowed. Products sent COD will either be rejected by D-Link or become the
property of D-Link. Products shall be fully insured by the customer. D-Link will not be held
responsible for any packages that are lost in transit to D-Link. The repaired or replaced
packages will be shipped to the customer via UPS Ground or any common carrier selected by
D-Link, with shipping charges prepaid. Expedited shipping is available if shipping charges are
prepaid by the customer and upon request.
D-Link may reject or return any product that is not packaged and shipped in strict compliance with the
foregoing requirements, or for which an RMA number is not visible from the outside of the package. The
product owner agrees to pay D-Link treasonable handling and return shipping charges for any product
that is not packaged and shipped in accordance with the foregoing requirements, or that is determined
by D-Link not to be defective or non-conforming.
What Is Not Covered: This limited warranty provided by D-Link does not cover: Products, if in D-Link t
judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse,
faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the
documentation for the product, or if the model or serial number has been altered, tampered with, defaced
or removed; Initial installation, installation and removal of the product for repair, and shipping costs;
Operational adjustments covered in the operating manual for the product, and normal maintenance;
Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage;
Any hardware, software, firmware or other products or services provided by anyone other than DLink; Products that have been purchased from inventory clearance or liquidation sales or other sales in
which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the
product. Repair by anyone other than D-Link or an Authorized D-Link Service Office will void this
Warranty.
Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE
PRODUCT IS PROVIDED BS-IS? WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING,
WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY
WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO
NINETY (90) DAYS. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED
HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS
WITH THE PURCHASER OF THE PRODUCT.
Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE
UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY
FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER,
WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO,
DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER
FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH DLINK TPRODUCT IS CONNECTEDWITH, LOSS OF INFORMATIONORDATA CONTAINED IN, STOREDON,
OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING
FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY
BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS
REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. THE MAXIMUM
55
LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT
COVERED BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIES
ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED OR
STATUTORY.
Governing Law: This Limited Warranty shall be governed by the laws of the State of California. Some
states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This limited
warranty provides specific legal rights and the product owner may also have other rights which vary
from state to state.
Trademarks: D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registered
trademarks are the property of their respective manufacturers or owners.
Copyright Statement: No part of this publication or documentation accompanying this Product may
be reproduced in any form or by any means or used to make any derivative such as translation,
transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as
stipulated by the United States Copyright Act of 1976. Contents are subject to change without prior
notice.Copyright© 2002 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.
CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communication. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
For detailed warranty outside the United States, please contact corresponding local
D-Link office.
FCC Caution:
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment; such modifications could void the user tauthority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. The antenna(s) used for this equipment must be installed to provide a separation
distance of at least eight inches (20 cm) from all persons.
This equipment must not be operated in conjunction with any other antenna.
56
Registration
Register your D-Link product online at http://support.dlink.com/register/
(11/08/2007)
57
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement