advertisement
Document revision 2.0.5 - Modified on 13/01/2015
Ordering Guide
FALCOM Product List
Valid from 01.09.2014
Phone: +49 (0)3677 8042-0
Fax : +49 (0)3677 8042-256
Terms & Conditions
General Terms: See our general terms & conditions on following weblink: http://www.falcom.de/contact/
More information: www.falcom.de | e-mail: [email protected]
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 1 of 38
Document revision 2.0.5 - Modified on 13/01/2015
Ordering Guide
Valid from 01 September 2014
Table Of Contents
AVL DEVICES:
PREMIUM FEATURES:
EVALUATION KITS:
ORDERING INFORMATION:
ABBREVIATIONS:
USED ABBREVIATIONS ................................................................................................................................................................................................................ 37
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 2 of 38
PRODUCT NAME
A) AVL DEVICES
FOX3
Fields of application:
Trucks, Buses, Light trucks,
Special vehicles
OPTIONS
NONE
NONE
Document revision 2.0.5 - Modified on 13/01/2015
DESCRIPTION NOTES
Standard version: Quad Band GSM/GPRS module, high sensitivity GNSS receiver, 3-axismotion-sensor (±8g), internal antennas, external antenna connectors, 8pin (2x4) main connector, 6pin accessory connector, 2.5mm audio port and 10pin mini-USB connector.
There is no installation cable in standard delivery included. It should be ordered separately.
Main Port 8pin
(2x4) connector includes:
RX_0, TX_0 : 1 x Serial port V.24 (1 st serial interface - SER0)
V+ : 1 x Power supply (10.8 - 32.0 VDC)
IGN : : 1 x Digital input (Ignition)
I/O : : 3 x Multi-function inputs/outputs
Accessory Port 6pin
(2x3) connector includes:
1-Wire : 1 x 1-Wire port.
RX_1/TX_1 : 1 x RS-232 port V24 level (2 nd serial interface - SER1)
I²C : : 1 x I²C interface
10pin
mini-USB connector includes:
USB : 1 x USB 2.0 port (DATA+, DATA-, USB detect)
SPI : 1 x SPI interface (MOSI, MISO, CLK, CS)
Audio port
:
2.5mm jack : Microphone + Speaker
See description FOX3-STARTERKIT , page 26
Certifications:
CE, E1
FOX3-EVALKIT
Accessories for FOX
3
B1
FAL-ANT-11
FAL-ANT-12
CA27
CA31
None
None
None
None
None
Rechargeable 1000 mAh Li-Polymer battery
Combined Quad Band GSM 850/900/1800/1900 and active GPS antenna incl. 2.5 m RG174 cable set with FAKRA-SMB connectors and double sided adhesive pad (not waterproof).
Combined Penta Band (GSM 850/900/1800/1900, 2.1-2.5GHz) and active GPS antenna incl.
2.5 m RG174 cable set with FAKRA-SMB connectors and double sided adhesive pad (not waterproof).
Main port programming cable with car charger. This cable connects to the main port of the
FOX3 and consists of the 8pin (2x4) connector, RS-232 port and car charger. Cable length: 1.50
m.
Main port extended installation cable (8/8 wires) with UCOM connector for interfacing
JAZZx/RFID. This cable connects to the main port of the FOX3 and consists of the 8pin (2x4) connector, a 4pin (2x2) UCOM connector and 6 x open end wires. Cable length: 1.50 m.
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 3 of 38
Document revision 2.0.5 - Modified on 13/01/2015
Accessories for FOX
3 (continued)
CA68
CA70
CA69
CA71
IOBOX-MINI
None
None
None
None
None
IOBOX-BT
IOBOX-CAN
None
None
RFID-A-B-EXT
RFID-TAGS-PACK-TYPEA
None
A
Main port extended installation cable (8/8 wires) with open ends. This installation cable consists of the 8pin (2x4) double row MOLEX connector and 8 x open end wires. Cable length:
1.50m.
Main port basic installation cable (3/8 wires) with open ends. This installation cable consists of the 8pin (2x4) connector and 3 x wires with open ends. Cable length: 1.50m.
Accessory port cable (6/6 wires) for 1-wire and UCOM connector for interfacing
additional JAZZx/RFID. This cable connects to the accessory port of the FOX3 and consists of the 6pin (2x3) connector, a 4pin (2x2) UCOM connector and 6 x open end wires. Cable length:
1.50 m.
Accessory port cable (6/6 wires) with open ends. This cable connects to the accessory port of the FOX3 and consists of the 6pin (2x3) connector and 6 x wires with open ends. Cable length: 1.50m.
I/O extension module for FOX3. It extends the functionality of the FOX3 by additional 13 inputs/outputs. The cable "CA38-STEPPIII-KFZ-1,5M" is required for connection of the I/Os to the vehicle signals/external system. It has 16-wires with a cable length of 1,5 meter.
This cable is not included in the IOBOX-MINI standard delivery, it has to be ordered separately.
16pin
MOLEX connector comprising :
IN : 8 x Digital inputs
OUT : 4 x Digital outputs
ANA : 1 x Analogue input
Hint: IOBOX-MINI can be used with FOX-IN/EN (with US option) and FOX3, however the RX and TX lines on the 16pin connector of the IOBOX-MINI are not supported when connected to the FOX3 device. These pins are available on the 6-pin accessory port and
CA69/CA71 cables respectively. For more details, refer to the FOX3 hardware manual.
BT4.0 + Bluetooth LE dual mode for FOX3 (in preparation)
K+L line, external extension box, extension to 2 CAN-Bus or additional CAN bus in case all 8wires of installation cable are already used for non-CAN-Bus items (in preparation)
12V-24V external RFID reader device ISO 14443, Type A/B. It consists of a 4pin (2x2) UCOM connector and 5.0 m cable length. It connects to the FOX3 device via CA31 cable.
RFID Transponder (Tag) Typ A (10 pcs. or 100 pcs.).
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 4 of 38
Document revision 2.0.5 - Modified on 13/01/2015
Interfaces/
Accessories
CA27
CA31
CA68
CA70
CA69
CA71
- Available
Audio
Interface
RFID
Interface
RS-232
Interface
FOX3
ACCESSORY MATRIX
Bar-Code Scanner
Interface
JAZZx
Interface
SPI interface
Voltage Converter
24-72V to 12V
Power
Car
Charger
I²C /
1-Wire
Notes
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 5 of 38
PRODUCT NAME
A) AVL DEVICES
STEPPIII-UX -X-Y
Fields of application:
Trucks, Buses, Special vehicles
OPTIONS
X = CH
Y = B1
Document revision 2.0.5 - Modified on 13/01/2015
DESCRIPTION NOTES
Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver, 3axis-motion-sensor (±3g), external GSM/GPS FAKRA-SMB antenna connectors, 16pin (2x8) connector, 15pin (1x15) connector, SIM card slot, 3 x LED indicators incl. 16pin automotive installation cable 1.5M.
For programming the device you need CA13 or CA25-A cable.
16pin
(2x8) connector includes:
IN : 7
x Inputs (4 x Digital/Analoge inputs, 3 x Digital inputs)
V+ : 1 x Power supply (10.8 - 32.0 VDC)
IGN : 1 x Digital input (ignition)
OUT : 4 x Digital outputs (open collector 100 mA)
15pin
(1x15) connector includes:
SERIAL : 2 x RS-232 ports (1 x V.24, 1 x TTL)
SPK/MIC
: 1
x Audio interface (for connecting a speaker and microphone device)
IGN : 1 x Digital input (ignition - the same IGN-pin as on 16pin connector)
V
OUT
: 2 x Power outputs (1 x 3.3VD/5VDC, 1 x battery voltage)
CAN-Bus interface (high speed CAN-Bus, CAN-FMS, CAN-OBD-II).
Certifications:
CE, E1, FCC,
PTCRB, AT&T
Internal rechargeable min. 1000 mAh Li-Polymer battery.
Accessories for STEPPIII-UX -X-Y
FAL-ANT-11
None
CH
B1
FAL-ANT-12
CA13
CA15
None
None
None
Combined Quad Band GSM 850/900/1800/1900 and active GPS antenna incl. 2.5 m RG174 cable set with FAKRA-SMB connectors and double sided adhesive pad (not waterproof).
Combined Penta Band (GSM 850/900/1800/1900, 2.1-2.5GHz) and active GPS antenna incl. 2.5
m RG174 cable set with FAKRA-SMB connectors and double sided adhesive pad (not waterproof).
Programming and audio connection cable with RS-232 serial port and audio jacks. It consists of a 15pin (1x15) AMP connector, an RS-232 serial port female connector and 2.5mm /
3.5mm female audio jacks.
Audio connection cable with audio jacks. It consists of a 15pin (1x15) AMP connector and
2.5mm/3.5mm female audio jacks.
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 6 of 38
Document revision 2.0.5 - Modified on 13/01/2015
PRODUCT NAME OPTIONS DESCRIPTION
A) AVL DEVICES
Accessories for STEPPIII-UX -X-Y (continued)
CA25X
CA37
CA38
X = A
X = B
None
None
A
B
Programming and audio connection cable with RS-232 serial port and audio jacks. It consists of a 15pin (1x15) AMP connector, 2.5mm / 3.5mm female audio jacks, a micro-USB connector (serial TTL level 3.3V) for connection with MFD1 device, a 4pin (2x2) UCOM connector for connecting the included RS-232 adapter cable with 4pin (2x2) UCOM connector.
RS-232 adapter cable with female connector (for PC).
RS-232 adapter cable with male connector for external peripheries (e.g. Serial Barcode Reader).
Adapter cable for connection STEPPIII with RFID. It consists of a 15-pin (1x15) AMP connector and a 4-pin (2x2) UCOM connector for connecting RFID-Reader device. Cable length ca. 21 cm.
Automotive connection cable and mounting cradle with 2A-Fuse. The connection cable has a length of 1.5m and a 16pin (2x8) connector. The mounting cradle is used to mount the STEPPIII device to a solid, flat, indoor surface. Please refer to the document
"STEPPIII_HardwareManual.pdf" for details how to mount it.
Audio Set
RFID-A-B-EXT
None
None
RFID-TAGS-PACK-TYPEA
None
FALCOM does not offer Audio set device, however it recommends to use active speaker and microphone.
Please refer to the electrical specifications for the MIC and SPK in the STEPPIII hardware manual.
12V-24V external RFID reader device ISO 14443, Type A/B. It consists of a 4pin (2x2) UCOM connector and 5.0m cable length. It connects to a STEPPIII device via CA37.
RFID Transponder (Tag) Typ A (10 pcs. or 100 pcs.).
KNT-100V-STEPPIII
CON-200
None
None
KNT-100V-STEPPIII is a voltage converter that converts input voltages from 24...72 VDC to 12
VDC usually used in trucks, buses, boats. This accessory provides reliable operation of STEPPIII device even during the high voltage spikes. KNT-100V has an input voltage rating from 24 VDC to
72 VDC and a fixed output voltage of 12 VDC. KNT-100V is already built into a STEPPIII installation cable. This cable has a 16pin (2x8) connector and 16 x open end wires with a length of
1.5mm. More details can be found in the manual
"KNT100V_TechnicalData.pdf
"
Counterpart of the STEPPIII-UX 15pin AMP connector to self build cables. 15-pin (1x15) AMP connector set (set of 10 pcs).
NOTES
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 7 of 38
Document revision 2.0.5 - Modified on 13/01/2015
Interfaces/
Accessories
FAL-ANT-11
Audio
Interface
RFID
Interface
FAL-ANT-12
CA13
CA15
CA25A
CA25B
CA37
CA38
KNT100V
- Available; * Female; ** Male;
RS-232
Interface
STEPPIII-UX -X-Y ACCESSORY MATRIX
Bar-Code
Scanner Interface
JAZZx
Interface
Antenna interfaces
Voltage Converter
24-72V to 12V
*
**
Power
Car
Charger
Notes
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 8 of 38
PRODUCT NAME
A) AVL DEVICES
BOLERO-LT2 -X-Y
Fields of application:
Cars, Light trucks, Motorbikes
MS
B1
Accessories for BOLERO-LT2
-X-Y
CA34
None
CA43
None
CA51
Suction foot
(vacuum cup)
KNT-100V-BOLERO-LT2
OPTIONS
X = MS
Y = B1
None
None
None
Document revision 2.0.5 - Modified on 13/01/2015
DESCRIPTION NOTES
Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver and internal GPS/GSM antennas, SIM-Card interface, 5pin (1x5) connector, 4 programmable
LED indicators
and 1 x free programmable push-button, incl. 3/5pin automotive installation cable 1.5 M and double sided adhesive pad (D=40 mm) for mounting.
BOLERO-LT2 does not support connection to RFID reader or JAZZx devices.
For programming the device you need CA43 cable.
5pin
(1x5) connector includes:
SERIAL : 1 x Serial port V.24, for firmware update and configuration ONLY.
V+ : 1 x Power supply (10.8 - 32.0 VDC)
IGN : : 1 x Digital input (ignition)
Certifications:
CE, E1
Built-in 3-axis-motion-sensor (±3g)
Internal rechargeable 1000 mAh Li-Polymer battery.
Power connection cable with Car Charger. It consists of a 5pin connector and a car charger with a cable length ca. 2 m.
Programming and power connection cable with RS-232 serial port and open ends. It consists of 5pin (1x5) MOLEX connector, RS-232 serial port connector and 2 open end wires for power supply with a cable length of 1.50m.
Adapter cable BOLERO-LT2 to BOLERO-LT installation cable. It consists of two connectors, one 5pin and a 6pin connector. This cable allows you to connect a BOLERO-LT2 to a BOLERO-
LT installation cable.
Suction foot with a 40 mm diameter adhesive pad for mounting BOLERO-LT2 on glass surfaces. This is a perfect accessory for BOLERO-LT2 when you need to attach it on the car's windshield.
KNT-100V-BOLERO-LT2 is a voltage converter that converts input voltages from 24...72 VDC to 12 VDC usually used in trucks, buses, boats. This accessory provides reliable operation of
BOLERO-LT2 device even during the high voltage spikes. KNT-100V has an input voltage rating from 24 VDC to 72 VDC and a fixed output voltage of 12 VDC. KNT-100V is already built into a
BOLERO-LT2 installation cable. This cable has a 5pin (1x5) connector and 3 x open end wires with a length of 1.5m. More details can be found in the manual "KNT100V_TechnicalData.pdf
"
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 9 of 38
Interfaces/
Accessories
CA34
CA43
CA51
KNT100V
- Available
Document revision 2.0.5 - Modified on 13/01/2015
Audio
Interface
RFID
Interface
RS-232
Interface
BOLERO-LT2 -X-Y ACCESSORY MATRIX
Bar-Code
Scanner Interface
JAZZx
Interface
Antenna interfaces
Voltage Converter
24-72V to 12V
Power
Car
Charger
Notes
Adapter Cable
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 10 of 38
PRODUCT NAME
A) AVL DEVICES
FOX-INX-Y-Z -AU
Fields of application:
Trucks, Buses, Light trucks,
Special vehicles
FOX-INX-Y-Z -US
Attention:
No AUDIO-Option possible
Fields of application:
Trucks, Buses, Light trucks,
Special vehicles
OPTIONS
X = CH
Y = BT
Z = B1
CH
BT
B1
X = CH
Y = BT
Z = B1
CH
BT
B1
Document revision 2.0.5 - Modified on 13/01/2015
DESCRIPTION NOTES
Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver, 3axis-motion-sensor (±3g), internal GSM/GPS antennas, 8pin (2x4) connector and 10pin mini-
USB connector with audio interface incl. 8pin automotive installation cable 1.5M.
8pin
(2x4) connector includes:
SERIAL : 1 x Serial port V.24.
V+ : 1 x Power supply (10.8 - 32.0 VDC)
IGN : : 1 x Digital input (ignition)
I/O : : 3 x Multi-function inputs/outputs
Certifications:
CE, E1
10pin
mini-USB connector includes (
Please don't connect the mini-USB to the PC
):
SERIAL : 1
x RS-232 port (TTL level)
SPK/MIC
: 1
x Audio interface (for connecting a speaker and microphone device)
CAN-Bus interface (high speed CAN-Bus, CAN-FMS, CAN-OBD-II).
Integrated Bluetooth (SPP - Serial Port Profile) module.
Internal rechargeable 1000 mAh Li-Polymer battery
Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver, 3axis-motion-sensor (±3g), internal GSM/GPS antennas, 8pin (2x4) connector and 10pin mini-
USB connector with SPI-Interface for customer extensions incl. automotive installation cable
1.5M.
8pin
(2x4) connector includes:
RX, TX : 1 x Serial port V.24.
V+ : 1 x Power supply (10.8 - 32.0 VDC)
IGN : : 1 x Digital input (ignition)
I/O : : 3 x Multi-function inputs/outputs
Certifications:
CE, E1
10pin
mini-USB connector includes (
Please don't connect the mini-USB to the PC
SERIAL : 1
x RS-232 port TTL level (if no BT-option available)
SPI : 1
x SPI interface (MOSI, MISO, CLK, CS)
):
CAN-Bus interface (high speed CAN-Bus, CAN-FMS, CAN-OBD-II).
Integrated Bluetooth (SPP - Serial Port Profile) module.
Internal rechargeable 1000 mAh Li-Polymer battery.
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 11 of 38
PRODUCT NAME
A) AVL DEVICES
FOX-ENX-Y -AU
Fields of application:
Trucks, Buses, Light trucks,
Special vehicles
FOX-ENX-Y-Z -US
Attention:
No AUDIO-Option possible
Fields of application:
Trucks, Buses, Light trucks,
Special vehicles
OPTIONS
X = CH
Y = B1
CH
B1
X = CH
Y = B1
Z = BT
CH
B1
BT
Document revision 2.0.5 - Modified on 13/01/2015
DESCRIPTION NOTES
Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver, 3axis-motion-sensor (±3g), external GSM/GPS FAKRA-SMB antenna connectors, 8pin (2x4) connector and 10pin mini-USB connector with audio interface incl. 8pin automotive
installation cable 1.5M.
8pin
(2x4) connector includes:
RX, TX : 1 x Serial port V.24.
V+ : 1 x Power supply (10.8 - 32.0 VDC)
IGN : : 1 x Digital input (Ignition)
I/O : : 3 x Multi-function inputs/outputs
Certifications:
CE, E1
10pin
mini-USB connector includes (
Please don't connect the mini-USB to the PC
):
SERIAL : 1 x RS-232 port TTL level
SPK/MIC : 1 x Audio interface (for connecting a speaker and microphone device)
CAN-Bus interface (high speed CAN-Bus, CAN-FMS, CAN-OBD-II).
Internal rechargeable 1000 mAh Li-Polymer battery
Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver, 3axis-motion-sensor (±3g), external GSM/GPS FAKRA-SMB antenna connectors, 8pin (2x4) connector and 10pin mini-USB connector with SPI interface for customer extensions incl.
automotive installation cable set 1.5M.
8pin
(2x4) connector includes:
RX, TX : 1 x Serial port V.24.
V+ : 1 x Power supply (10.8 - 32.0 VDC)
IGN : : 1 x Digital input (Ignition)
I/O : : 3 x Multi-function inputs/outputs
Certifications: CE, E1
10pin
mini-USB connector includes (
Please don't connect the mini-USB to the PC
SERIAL : 1
x RS-232 port TTL level (if no BT-option available)
SPI : 1
x SPI interface (MOSI, MISO, CLK, CS)
):
CAN-Bus interface (high speed CAN-Bus, CAN-FMS, CAN-OBD-II).
Internal rechargeable 1000 mAh Li-Polymer battery.
Integrated Bluetooth (SPP - Serial Port Profile) module
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 12 of 38
Document revision 2.0.5 - Modified on 13/01/2015
PRODUCT NAME OPTIONS DESCRIPTION
A) AVL DEVICES
Accessories for FOX-IN-
X-Y-Z
-AU /US & FOX-ENX-Y -AU/US
IOBOX-MINI
FAL-ANT-11
FAL-ANT-12
CA27
CA28
CA31
CA39
RFID-A-B-EXT
None
None
None
None
None
None
None
None
RFID-TAGS-PACK-TYPEA
None
IO-BOX with 16-pin IO connector, external extension box for FOX-IN/EN-US. No further cable needed for connection, it plugs to the FOX-IN/EN-US device via the mini-USB interface.
The IOBOX-MINI is an external extension box for the FOX-IN/EN-US devices (without BT-
Option) to extend their connectivity and functionality when more I/Os are needed. The 16pin
MOLEX connector has the following pins:
16pin
connector includes:
IN/ OUT : 8 x Digital inputs; 4 x Digital outputs
ANA : 1 x Analogue input;
SERIAL : 1 x Serial port V.24
For FOX-EN only. Combined Quad Band GSM 850/900/1800/1900 and active GPS antenna incl. 2.5 m RG174 cable set with FAKRA-SMB connectors and double sided adhesive pad (not waterproof).
For FOX-EN only. Combined Penta Band (GSM 850/900/1800/1900, 2.1-2.5GHz) and active
GPS antenna incl. 2.5 m RG174 cable set with FAKRA-SMB connectors and double sided adhesive pad (not waterproof).
Programming and power connection cable with RS-232 serial port and car charger. This cable set consists of the 8pin (2x4) connector, an RS-232 serial port connector and a car charger. Cable length: 1.50 m.
FOX-IN/EN-AU Audio connection cable with mini-USB connector and audio jacks. This cable consists of a mini-USB connector and 3.5mm/2.5mm mini jacks for connecting an Audio
Set device.
Installation and JAZZx/RFID connection cable with 2A fuse. This installation cable consists of the 8pin (2x4) connector, a 4pin (2x2) UCOM connector and 6 x open end wires. Cable length: 1.50 m. The pinout of this cable can be found in the hardware manual of FOX-EN/IN.
FOX-IN/EN standard installation cable. This cable is already included in the FOX-IN/EN standard delivery and consists of 2x4pin MOLEX connector with open ends. Cable length:
1.5m.
12V-24V external RFID reader device ISO 14443, Type A/B. It consists of a 4pin (2x2) UCOM connector and 5.0m cable length. It connects to a FOX-IN/EN device via CA31 cable.
RFID Transponder (Tag) Typ A (10 pcs. or 100 pcs.).
NOTES
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 13 of 38
Document revision 2.0.5 - Modified on 13/01/2015
PRODUCT NAME OPTIONS DESCRIPTION
Accessories for FOX-IN-
X-Y-Z
-AU /US & FOX-ENX-Y -AU/US
(continued)
KNT-100V-FOX-IN/EN
None KNT-100V-FOX-IN/EN is a voltage converter that converts input voltages from 24...72 VDC to
12 VDC usually used in trucks, buses, boats. This accessory provides reliable operation of
FOX-IN/EN device even during the high voltage spikes. KNT-100V has an input voltage rating from 24 VDC to 72 VDC and a fixed output voltage of 12 VDC. KNT-100V comes as a separate cable and should be manually connected to the FOX-IN/EN installation cable. This cable has a
8pin (2x4) connector and 8 x open end wires with a length of 1.5mm. More details can be found in the manual "KNT100V_TechnicalData.pdf
"
Interfaces/
Accessories
CA27
CA28
CA31
CA39
KNT100V
IOBOX-MINI
- Available
Audio
Interface
RFID
Interface
FOX-IN-
X-Y-Z -AU /US & FOX-ENX-Y -AU/US ACCESSORY MATRIX
RS-232
Interface
Bar-Code
Scanner Interface
JAZZx
Interface
Antenna interfaces
Voltage Converter
24-72V to 12V
Power
Car
Charger
NOTES
Notes
AU
US
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 14 of 38
Document revision 2.0.5 - Modified on 13/01/2015
Interfaces/
Accessories
FAL-ANT-11
FAL-ANT-12
CA27
CA28
CA31
CA39
KNT100V
IO-BOX
- Available
Audio
Interface
RFID
Interface
RS-232
Interface
FOX-EN ACCESSORY MATRIX
Bar-Code
Scanner Interface
JAZZx
Interface
Antenna interfaces
Voltage Converter
24-72V to 12V
Power Car
Charger
Notes
AU
US
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 15 of 38
Document revision 2.0.5 - Modified on 13/01/2015
PRODUCT NAME OPTIONS DESCRIPTION NOTES
A) AVL DEVICES (Interface to AVL devices)
JAZZ1-WIN6.0
JAZZ2-GPS+AND4
JAZZ2-
GPS+GPRS+BT+WIFI+AND4
NONE
NONE
NONE
Multi functional display 5“ (11,2 cm) TFT display with integrated built-in GPS receiver
. Resolution: 480 x 272 pixel,
65k resistive touch-screen, embedded CPU 500MHz, 128MB DDR RAM, 2GB
FLASH, micro SD card slot, power ON/OFF/Back button, USB 2.0 compliant 5 V, Windows CE 6.0,
FALCOM demo application/software, fully configurable one finger GUI.
FALCOM strongly recommends to use and charge the JAZZx only via the AVL Car-Connection-Kit
(Cradle). If you don't use the JAZZxx while it is mounted on its cradle, we recommend to switch it off, to accelerate the charging process.
The standard delivery contents includes:
JAZZ1-WIN + USB programming cable + Car charger
EOL.
LTB:
30.06.2013
LTO:
30.09.2013
Available as ODM product with
MOQ=500pcs
Multi functional display 5“ TFT display with integrated built-in 64 channels GPS receiver and internal rechargeable battery 2300mAh
. Resolution 800 x 480 pixel, 65k resistive touch-screen, embedded
CPU 1GHz, 256MB RAM, 512 MB internal flash memory, 2GB FLASH, micro SD card slot, power
ON/OFF/Back button, USB 2.0 compliant 5 V, Android 4.0.
FALCOM strongly recommends to use and charge the JAZZx only via the AVL Car-Connection-Kit
(Cradle). If you don't use the JAZZxx while it is mounted on its cradle, we recommend to switch it off, to accelerate the charging process.
The standard delivery contents includes:
JAZZ2-GPS+AND4
+ USB programming cable + Car charger
Certifications: CE
NPI: 9/2013
Multi functional display 5“ TFT display with integrated built-in 64 channels GPS receiver, Quad-Band
GSM/GPRS module, Bluetooth V2.1 (OPP,SPP,...) and WiFi IEEE 802.11 b/g, internal rechargeable battery 2300mAh
. Resolution: 800 x 480 pixel, 65k resistive touch-screen, embedded CPU 1GHz,
256
MB RAM, 512 MB internal flash memory, 2GB FLASH, micro SD card slot, power
ON/OFF/Back button, USB 2.0 compliant 5 V, Android 4.0.
FALCOM strongly recommends to use and charge the JAZZx only via the AVL Car-Connection-Kit
(Cradle). If you don't use the JAZZxx while it is mounted on its cradle, we recommend to switch it off, to accelerate the charging process.
The standard delivery contents includes:
JAZZ2-GPS+GPRS+BT+WIFI+AND4
+ USB programming cable + Car charger
Certifications: CE
NPI: 7/2013
Accessories for JAZZ1-WIN6.0, JAZZ2-GPS+AND4 & JAZZ2-GPS+GPRS+BT+WIFI+AND4
AVL Car-Connection-Kit
None Car connection kit to connect JAZZX to a FALCOM AVL device. This kit consists of a cradle including: 1.0 m cable with a 4pin (2x2) UCOM connector to connect the JAZZ2 to an AVL device via one of the following listed cables. It must be ordered together with one of the following cables:
CA31 : FOX-IN/EN installation cable
CA32 : DISCO installation cable
MANDATORY
You may also need the Car-Mounting-Kit (vehicle suction foot) to mount it on your car windshield.
See Car-Mounting-Kit accessory listed below.
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 16 of 38
Document revision 2.0.5 - Modified on 13/01/2015
PRODUCT NAME OPTIONS DESCRIPTION
Accessories for JAZZ1-WIN6.0, JAZZ2-GPS+AND4 & JAZZ2-GPS+GPRS+BT+WIFI+AND4 (continued)
Car-Mounting-Kit
Car-Connection-Kit RS-
232
None
None
This car mounting kit allows you to use the JAZZx in a car. It consists of a vehicle suction foot which can be directly mounted to the JAZZ1 but NOT to the JAZZ2. When using JAZZ2, this kit must be ordered together with
AVL Car-Connection-Kit or Car-Connection-Kit RS-232.
Car-Mounting-Kit can NOT be mounted directly to the JAZZ2.
Kit for using the JAZZ1 alone without AVL device. This kit consists of a cradle including: 1.0 m cable with a RS-232 port and a mini-USB port.
NOTES
Interfaces/
Accessories
AVL Car-
Connection-Kit
Car-Mounting-Kit
Audio
Interface
JAZZ1-WIN6.0, JAZZ2-GPS+AND4 & JAZZ2-GPS+GPRS+BT+WIFI+AND4
ACCESSORY MATRIX
RFID
Interface
RS-232
Interface
Bar-Code
Scanner Interface
JAZZx
Interface
Antenna interfaces
Voltage Converter
24-72V to 12V
Power Car
Charger
Car-Connection-
Kit RS-232
- Available
Notes
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 17 of 38
Document revision 2.0.5 - Modified on 13/01/2015
PRODUCT NAME OPTIONS DESCRIPTION NOTES
B) ASSET TRACKING & TERMINAL ASSET DEVICES
DISCOX-Y-Z -AU
Fields of application:
Trucks, Buses, Light trucks,
Trains, Special vehicles
X = CH
Y = B4 or BX
Z = GLON
CH
B4
BX
GLON
Accessories for DISCO-
X-Y-Z -AU
Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver,
3-axis-motion-sensor (±3g), internal GSM/GPS antennas, internal SIM-card holder, protection class IP69K, mounting kit and external cable (1m) including:
Audio
- 2 x Audio jacks (for speaker and microphone),
- 1 x 8pin single row connector for data + power + IO (Input/Outputs),
- 1 x 4pin single row connector for connection to MFD1.
jacks includes:
SPK : 1 x 3.5mm jack for connecting a speaker device.
MIC :
1 x 2.5mm jack for connecting a microphone device.
6/8pin
(1x8) connector includes:
RX, TX : 1 x Serial port V.24
V+ : 1 x Power supply (10.8 - 32.0 VDC)
IGN : 1 x Digital input (Ignition)
I/O : 2 x Multi-function inputs/outputs
4pin
(2x2) connector includes:
RX,TX : 1 x RS-232 port 3.3V TTL
V+ : 1 x Power supply for MFD1 device
CAN-Bus interface (high speed CAN-Bus, CAN-FMS, CAN-OBD-II).
Certifications: CE, E1
Internal rechargeable 2250mAh Li-Polymer battery
Internal rechargeable battery 4800mAh with extended temperature range
Built-in GLONASS (Russian Navigation System) incl. GPS receiver
CA20
CA32
Audio Set
RFID-A-B-EXT
None
None
None
None
Programming and power/charging connection cable with RS-232 serial port and car
charger. This cable consists of 8pin (1x8) connector, RS-232 serial port connector and a car charger for supplying power to the device. Cable length: 1.50 m
Installation and JAZZx/RFID connection cable with 2A fuse. This cable consists of the
8pin (1x8) connector, a 4pin (2x2) connector for connecting a JAZZ1/RFID-reader and 6 x open end wires. Cable length: 1.50 m
FALCOM does not offer Audio set device, however it recommends to use active speaker and microphone.
5V-12V External RFID reader device ISO 14443, Type A/B. It consists of a 4pin (2x2) connector and 5.0m cable length. It connects to a DISCO-AU device via CA32 cable.
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 18 of 38
Document revision 2.0.5 - Modified on 13/01/2015
PRODUCT NAME OPTIONS DESCRIPTION
Accessories for DISCO-
X-Y-Z -AU
(continued)
RFID-TAGS-PACK-TYPEA
None
DISCO-PC-SET-X X = 1
X = 2
RFID Transponder (Tag) Typ A (10 pcs. or 100 pcs.).
1 - Pylon Clamp-Set (2 x mast mounting clamps, V4A steel, salt-water proof).
2 - Mounting Kit (Already available in the standard delivery contents).
Interfaces/
Accessories
CA20
CA32
- Available
Audio
Interface
RFID
Interface
RS-232
Interface
DISCO-
X-Y-Z -AU ACCESSORY MATRIX
Bar-Code
Scanner Interface
JAZZ1
Interface
Antenna interfaces
Voltage Converter
24-72V to 12V
Power
Car
Charger
NOTES
Notes
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 19 of 38
Document revision 2.0.5 - Modified on 13/01/2015
PRODUCT NAME OPTIONS DESCRIPTION NOTES
B) ASSET TRACKING & TERMINAL ASSET DEVICES
DISCO-B5-MAGNET
Fields of application:
Trucks, Buses, Light trucks,
Trains, Special vehicles
None Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver, 3axis-motion-sensor (±3g), internal GSM/GPS antennas, internal SIM-card holder, internal battery pack (5x2250 mAh), protection class IP69K, 6 x magnetic mounts, inside light/dark sensor, 2 x external buttons for truck mount/demount detections and 6/8pin round
(Flanschdose) female socket.
For programming the device you need CA33 cable (see accessory section below).
8pin
round (Flanschdose) female connector includes:
RX, TX : 1 x Serial port V.24
V+ : 1 x Power supply (10.8 - 32.0 VDC)
IGN : : 1x Digital input (Ignition)
I/O : : 3 x Multi-function inputs/outputs
Certifications:
CE, E1
4pin
(1x4) connector includes:
RX,TX : 1 x RS-232 port 3.3V TTL
V+ :
1 x Power supply for MFD1 device
Accessories for DISCO-B5-MAGNET
CA33
None
Programming and power/charge connection cable with RS-232 serial port and Wall
Adapter Power Supply. This cable consists of an 8-pin round (Flanschdose) male-connector, an RS-232 serial port connector for configuration and an AC-DC wall adapter power supply (EU) for charging the internal batteries.
Interfaces/
Accessories
CA33
- Available
Audio
Interface
RFID
Interface
RS-232
Interface
DISCO-B5-MAGNET ACCESSORY MATRIX
Bar-Code
Scanner Interface
JAZZ1
Interface
Antenna interfaces
Voltage Converter
24-72V to 12V
Power
(
Wall Adapter)
Car
Charger
Notes
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 20 of 38
Document revision 2.0.5 - Modified on 13/01/2015
PRODUCT NAME OPTIONS DESCRIPTION NOTES
B) ASSET TRACKING & TERMINAL ASSET DEVICES
ROCK
Fields of application:
Container monitoring, Data logger
None Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver, 3axis-motion-sensor (±3g), internal GSM/GPS antennas, internal SIM-card holder, internal nonrechargeable LR20 battery-block (7V / 5x2250mAh), assembled by 4 standard cross-screws,
IP67 waterproof and shock-resistant case.
Certifications: CE, E1.
EOL.
LTB:
30.06.2013
LTO:
30.09.2013
Available as ODM product with MOQ=500pcs.
Accessories for ROCK
CA44
None
Safety Screw Set ROCK
None
ROCK Battery-Block
None
Programming connection cable with USB port. It consists of a 3pin (1x3) and an USB connector. Please refer to the ROCK hardware manual for details how to connect this cable with ROCK. To communicate with ROCK device you have to download and install FTDI driver from this website: http://www.ftdichip.com
Anti-theft screws ideal to assemble and keep your device safe. This set consists of 4 x safety screws and corresponding 1 x screwdriver bit.
ROCK back-up/replacement battery-block 5-cell LR20 battery-block (7,5V/10 Ah) incl. cable with connector (3pin) to ROCK PCB connection. Please refer to the hardware manual of the
ROCK for details how to replace the battery-pack.
Interfaces/
Accessories
CA44
- Available
Audio
Interface
RFID
Interface
USB
Interface
ROCK ACCESSORY MATRIX
Bar-Code
Scanner Interface
JAZZ1
Interface
Antenna interfaces
Voltage Converter
24-72V to 12V
Power Car
Charger
Notes
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 21 of 38
Document revision 2.0.5 - Modified on 13/01/2015
PRODUCT NAME OPTIONS DESCRIPTION
B) ASSET TRACKING & TERMINAL ASSET DEVICES
MTR-1X -RF
Fields of application:
Mobile time registration system
X = GPS Standard version: Complete Terminal with FOX-IN based communication module and integrated
RFID reader (ISO 14443) Type A/B, 4 x free configurable buttons (13.2 x 18.6mm), 3 x free programmable LED indicators, internal GSM/GPS antennas, 5.5mm jack for ext. power supply, inside SIM card holder, internal Lithium-Lion backup battery (700 mAh) incl. AC/DC power adapter (110...240V).
GPS
Built-in 50 channel high sensitivity GPS receiver
Accessories for MTR-1-RF
CA-FOX-8-2x4
CA27
None
None
Adapter cable for CA27 with an 8pin (1x8) and 8pin (2x4) male connectors. It must be ordered together with CA27. For more details how to connect it to the MTR-1-RF PCB, refer to the MRT-
1-RF hardware manual.
FOX-EN/IN Programming and power connection cable with RS-232 serial port and car
charger. It consists of 8pin (2x4) female connector, RS-232 serial port connector and a car charger adapter. Cable length: 1.50 m. It must be ordered together with CA-FOX-8-2x4.
Interfaces/
Accessories
CA-FOX-8-2x4
CA27
- Available
Audio
Interface
RFID
Interface
RS-232
Interface
MTR-1X -RF ACCESSORY MATRIX
Bar-Code
Scanner Interface
JAZZ1
Interface
Antenna interfaces
Voltage Converter
24-72V to 12V
Power Car
Charger
NOTES
Notes
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 22 of 38
Document revision 2.0.5 - Modified on 13/01/2015
PRODUCT NAME OPTIONS
E) PERSONAL TRACKING DEVICES
MAMBO2-B6
None
Fields of application:
Personal tracker, Data logger
DESCRIPTION NOTES
Standard version: Quad Band GSM/GPRS module, 50 channel high sensitivity GPS receiver based on u-blox chipset, full colour OLED display (128 x 128), 5-way navigation button, 2 x control buttons, 1 x r eset button, hands-free speaking, internal Li-polymer battery 1650 mAh, 3axis-motion-sensor, c ustomizable GUI,
SOS function, man-down detection,
SIM card slot,
Internal speaker and microphone, and mini-USB port for data and charging incl. USB-to-mini-
USB cable.
The standard MAMBO2-B6 is available in three versions:
1) Orange/Black casing with Silver buttons
2) Black/Black casing with Silver buttons
3) Black/Black casing with Red/Green buttons
Certifications: CE, SAR,
FCC
Accessories for MAMBO2-B6
Docking-Station
Car-Mounting-Kit
None
None
Docking Station Set with quick charge. This docking station allows you to use your
MAMBO2-B6 in your home, office etc. It consists of the Base plate, Holding cradle, 9V AC/DC wall adapter power supply with mini-USB port and EU-,US- or UK-plug. Please refer to the document "Docking-Station.pdf" for details how to assemble it.
Car-Mounting-Kit with Car charger
. This car mounting kit allows you to use your
MAMBO2-B6 in a car. This kit consists of vehicle suction foot, holding frame, base plate,
USBto-mini-USB power cable
, car charger with USB port, 4 x screws and 1 x Allen key
®
. Please refer to the document "Car-Mounting-Kit.pdf" for details how to assemble it.
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 23 of 38
Document revision 2.0.5 - Modified on 13/01/2015
PRODUCT NAME OPTIONS DESCRIPTION NOTES
F) FIRMWARE & HARDWARE PREMIUM FEATURES FOR AVL DEVICES
The PREMIUM-FEATURES are extensions (APP) which are implemented in the standard FALCOM AVL firmware version 2.11.x
and higher to provide more applications and additional functionalities. These features need to be activated before use by purchasing the corresponding unique activation keys which are different for each premium feature and AVL device. The activation keys are linked to the serial numbers of FALCOM devices and will be generated by FALCOM only. A web server will be provided soon by FALCOM to download these features and enter manually the generated keys into the devices by yourselves using the corresponding PFAL command. The PREMIUM-Features can be individually activated in the AVL devices during installation as well as in the AVL devices already deployed in the field.
FIRMWARE & HARDWARE PREMIUM FEATURES
ECO DRIVE GPS
AES128
INDEXED HISTORY
EXTENDED-GEOFENCES
EXTENDED-ALARMS
CAN-INTERFACE ( FOX3
RS-485-INTERFACE (
)
FOX3 )
None
None
None
None
None
None
None
ECODrive is a feature based on GPS only. ECOdrive enables fleet managers and drivers to always keep track of current fuel consumption and driving style for helping them analyse to improve driving efficiency.
AES is the Advanced Encryption Standard, a United States government standard algorithm for encrypting and decrypting data that offers a higher level of security over GPRS / TCP using 128bit group encryption with 128 key length.
The indexed history feature enables reading of specific number of lines in the history. Before using this feature you have to clear the old history records in the device.
This extended geofences feature allows you to create up to 3000 Geofences and receive a notification when a geofence event occurs. This feature can be used i.e. for bus tracking and logistic projects.
This extended alarm feature extends the number of alarms that can be configured in the AVL device up to 250 where in the standard AVL firmware versions the number of alarms is limited to
100. The increased number of alarms allow you to use more alerts and thus more flexibility and functionality of the firmware in order to meet the user requirements.
This feature activates the CAN-Bus chip in the FOX3 and forwards CAN/CANFMS /CAN-OBDII messages in real time to third-party's application database.
This feature reconfigures the second RS-232 interface in the FOX3 standard hardware to the
RS-485 interface for the communication with sensors using RS-485 interface.
Only for FOX3
Only for FOX3
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 24 of 38
Document revision 2.0.5 - Modified on 13/01/2015
EVALUATION KIT
For an effectively evaluation and demonstration performance of the AVL device and being able to place orders, the purchase of its EVALUATION KIT is essential. It comes with following contents:
•
1 x AVL Unit shipped pre-configured with all needed accessories
•
1 x Pre-charged SIM-Card supporting GPRS for data transmission
•
1 x 6 Month Free Access to Trace4You Server Frontend
•
Access to complete documentation of the dedicated product
•
Free support for starting up your project
•
Free software and firmware upgrades (for series of standard devices)
Our Evaluation kits are shipped pre-configured, with all settings needed for fast evaluation and demonstration. The evaluation board in the Evalkit contains everything needed for helping you to evaluate your application results. You don’t need anything else than the EVALKIT to get started. In just a few minutes, you can set up your Evalkit and the AVL device goes online. You only need an
Internet enabled computer (PC client) with a pre-installed standard web browser for accessing the device from the t4y server frontend. Falcom Workbench-Software tool can be downloaded free of charge for local evaluation:
see: http://www.falcom.de/support/software-tools/falcom-workbench/
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 25 of 38
PRODUCT NAME
EVALKITS
FOX3-STARTERKIT
OPTIONS
None
Document revision 2.0.5 - Modified on 13/01/2015
DESCRIPTION NOTES
The FOX3 Starterkit provides a quick and simple way to test and maximize the performance of the applications you develop. RoHS compliant.
STARTERKIT
contents:
- 1 x FOX3 unit
- 1 x Rechargeable back-up battery
- 1 x CA31 - Main port extended installation cable 1,5m, 8pin double row MOLEX connector, 4pin double row UCOM connector for connecting RFID reader or JAZZ2 and open ends.
- 1 x CA69 - Accessory port cable 1,5m, 6pin double row MOLEX connector, 4pin double row UCOM connector and open ends.
- 1 x Control-Box with main and accessory ports containing (cable length: 50 cm) :
- 8pin (2x4) MOLEX connector (it connects to the FOX3 main port).
- 6pin (2x3) MOLEX connector (it connects to the FOX3 accessory port).
- Contol-Box with 5 x LED indicators (1 x Power LED green, 3 x I/O LED red and 1 x IGN
LED red) and 5 x switches for controlling the Power supply, 3 x I/Os and 1 x IGN.
- a 9-pin SUB-D connector for the RS-232 data channel (it connects FOX3 to a PC via your
RS-232 cable). It is known in the firmware as "Serial0" - 1 st serial interface - SER0 .
- Input power jack (12 - 32 VDC)
-
Power supply + US/UK/AU/EU adaptors
-
Online access to the latest user documentation
Available in Q1/2015
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 26 of 38
PRODUCT NAME
FOX3-EVALKIT
Document revision 2.0.5 - Modified on 13/01/2015
OPTIONS
None
DESCRIPTION
Complete plug and play evaluation system for the FOX3 device. RoHS compliant. This delivery consists of 1 box:
NOTES
EVALKIT contents:
- 1 x FOX3 unit shipped pre-configured with all PREMIUM-Features activated
- 1 x Rechargeable back-up battery
- 1 x FOX-EVALBOARD
- 1 x Adapter cable, connects FOX3 device to the FOX-EVALBOARD
- 1 x RS-232 serial cable, connects EVALBOARD to a PC
- 1 x Headset, connects to audio ports for testing audio features
- 1 x EU AC/DC power adapter, type FW7238/12
- 1 x US adapter
- 1 x UK adapter
- 1 x IOBOX-CAN
- 1 x Key for closing and opening the box
- 1 x Main port extended installation (CA68) cable 1,5m, 8pin double row MOLEX connector with open ends.
- 1 x CA38 - IOBOX-CAN installation cable 1,5m, 16pin double row MOLEX connector with open ends.
- 1 x Prepaid pre-charged SIM card and 6 months access to the FALCOM web server for evaluation purposes *.
- 1 x Infosheet, contains all information needed to get started with FOX3-EVALKIT (SIM card information, login data for accessing necessary online documentation and trace4you server frontend).
- 1 x Installation instruction sheet, contains necessary information about getting started with a FOX3 device.
- 1 x Day (8 hours) free technical training online or at FALCOM company.
Available in
Q1/2015
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 27 of 38
PRODUCT NAME
EVALKITS
STEPPIII-UX-EVALKIT
OPTIONS
None
Document revision 2.0.5 - Modified on 13/01/2015
DESCRIPTION
Complete plug and play evaluation concept for the STEPPIII-UX device.
RoHS compliant. This kit consists of 2 boxes:
1 - STEPPIII-UX-EVALBOX:
-
1 x STEPPIII-UX-CH-B1 unit shipped pre-configured ( demo configuration)
- 1 x FAL-ANT-11 combined GSM/GPS antenna
- 1 x Mounting cradle with mounting screws
-
1 x 16pin automotive installation cable 1,5m with 2A fuse protection
- 1 x Prepaid pre-charged SIM card and 6 months access to the FALCOM web server for evaluation purposes *.
2 - STEPPIII-UX-EVAL-ACCESSORIES:
- 1 x STEPPIII-EVALBOARD
- 1 x 15pin AMP to 15pin AMP cable (connects device to the EVALBOARD)
- 1 x 16pin MOLEX to 16pin MOLEX cable (connects device to the EVALBOARD)
- 1 x RS-232 Serial Cable, connects EVALBOARD to a PC
- 1 x Headset-UWT
- 1 x EU AC/DC Power Adapter, type FW7238/12
- 1 x US adapter
- 1 x UK adapter
- 1 x Key for closing and opening the box
- 1 x Infosheet, contains all information needed to get started with STEPPIII-UX-EVALKIT
(SIM card information, login data for accessing necessary online documentation and trace4you server frontend).
- 1 x Installation instruction sheet, contains necessary information about getting started with a STEPPIII-UX device.
*Attention: The prepaid SIM card is not available for all countries. The 6 months access to the
FALCOM demo web server is not part of FALCOM’s liabilities but a voluntary offer free-of-charge for
STEPPIII-UX-EVALKIT buyers for evaluation and demonstration purposes and without responsibility.
NOTES
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 28 of 38
PRODUCT NAME
EVALKITS
FOX-IN-AU(US)-EVALKIT
OPTIONS
None
Document revision 2.0.5 - Modified on 13/01/2015
DESCRIPTION
Complete plug and play evaluation system for the FOX-IN-AU or FOX-IN-US device.
RoHS compliant. This delivery consists of 1 box:
Package
contents
:
-
1 x FOX-IN-CH-B1-AU or FOX-IN-US-CH-B1 unit shipped pre-configured
- 1 x Built-in rechargeable 1000 mAh Li-Polymer battery
- 1 x FOX-EVALBOARD
- 1 x Adapter cable, connects FOX-IN device to FOX-EVALBOARD
- 1 x RS-232 serial cable, connects EVALBOARD to a PC
- 1 x Headset, connects to the mini-USB-port for testing audio features of the device
(FOX-IN-AU-EVALKIT only)
- 1 x EU AC/DC power adapter, type FW7238/12
- 1 x US adapter
- 1 x UK adapter
- 1 x Key for closing and opening the box
- 1 x Installation cable 1,5m with 2A fuse protection, 8pin connector with unstripped ends.
- 1 x Prepaid pre-charged SIM card and 6 months access to the FALCOM web server for evaluation purposes *.
- 1 x Infosheet, contains all information needed to get started with FOX-IN-EVALKIT
(SIM card information, login data for accessing necessary online documentation and trace4you server frontend).
- 1 x Installation instruction sheet, contains necessary information about getting started with a FOX-IN device.
*Attention: The prepaid SIM card is not available for all countries. The 6 months access to the
FALCOM demo web server is not part of the FALCOM’s liabilities but a voluntary offer free-ofcharge for FOX-IN-AU(US)-EVALKIT buyers for evaluation and demonstration purposes and without responsibility.
NOTES
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 29 of 38
PRODUCT NAME
EVALKITS
FOX-EN-AU(US)-EVALKIT
OPTIONS
None
Document revision 2.0.5 - Modified on 13/01/2015
DESCRIPTION
Complete plug and play evaluation system for the FOX-EN-AU or FOX-EN-US device.
RoHS compliant. This delivery consists of 1 box:
Package
contents
:
-
1 x FOX-EN-CH-B1-AU or FOX-EN-US-CH-B1 unit shipped pre-configured
- 1 x Built-in rechargeable 1000 mAh Li-Polymer battery
- 1 x FOX-EVALBOARD
- 1 x Adapter cable, connects FOX-EN device to FOX-EVALBOARD
- 1 x RS-232 serial cable, connects EVALBOARD to a PC
- 1 x Headset, connects to the mini-USB-port for testing audio features of the device
(FOX-EN-AU-EVALKIT only)
- 1 x EU AC/DC power adapter, type FW7238/12
- 1 x US adapter
-
1 x UK adapter
- 1 x Key for closing and opening the box
- 1 x Installation cable 1,5m with 2A fuse protection, 8pin connector and unstripped ends.
- 1 x Prepaid pre-charged SIM card and 6 months access to the FALCOM web server for evaluation purposes *.
- 1 x Infosheet, contains all information needed to get started with FOX-EN-EVALKIT
(SIM card information, login data for accessing necessary online documentation and trace4you server frontend).
- 1 x Installation instruction sheet, contains necessary information about getting started with a FOX-EN device.
*Attention: The prepaid SIM card is not available for all countries. The 6 months access to the
FALCOM demo web server is not part of the FALCOM’s liabilities but a voluntary offer free-ofcharge for FOX-EN-EVALKIT buyers for evaluation and demonstration purposes and without responsibility.
NOTES
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 30 of 38
PRODUCT NAME
EVALKITS
BOLERO-LT2-EVALKIT
OPTIONS
None
Document revision 2.0.5 - Modified on 13/01/2015
DESCRIPTION
Complete plug and play evaluation system for the BOLERO-LT2-MS-B1 device.
RoHS compliant. This delivery consists of 1 box:
Package
contents
:
1 x BOLERO-LT2-MS-B1 unit shipped pre-configured
1 x BOLERO-LT-EVALBOARD
1 x CA51 cable for connecting device to Evalboard
1 x RS-232 serial cable, connects EVALBOARD to a PC
1 x Double sided adhesive pad (D=40 mm)
1 x EU AC/DC power adapter, type FW7238/12
1 x US adapter
1 x UK adapter
1 x Key for closing and opening the box
1 x 3/5pin Automotive installation cable 1,5m.
1 x Infosheet, contains all information needed to get started with BOLERO-LT2 (SIM card information, login data for accessing necessary online documentation and trace4you server frontend).
1 x Prepaid pre-charged SIM card and 6 months access to the FALCOM web server for evaluation purposes*.
*Attention: The prepaid SIM card is not available for all countries. The 6 months access to the
FALCOM demo web server is not part of the FALCOM’s liabilities but a voluntary offer free-ofcharge for
BOLERO-LT2
-EVALKIT buyers for evaluation and demonstration purposes and without responsibility.
NOTES
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 31 of 38
PRODUCT NAME
EVALKITS
DISCO-B4-EVALKIT
OPTIONS
None
Document revision 2.0.5 - Modified on 13/01/2015
DESCRIPTION
Complete plug and play evaluation system for the DISCO-B4 device. RoHS compliant.
This delivery consists of 1 box:
Package
contents
:
- 1 x DISCO-B4 unit shipped pre-configured
- 1 x Built-in rechargeable 2250 mAh Li-Polymer battery
- 1 x FOX-EVALBOARD
- 1 x Connection cable to FOX-EVALBOARD
- 1 x RS-232 serial cable, connects EVALBOARD to a PC
- 12 x TORX screws 22 x 8 mm
- 6 x Rubber feet
- 1 x EU AC/DC power adapter, type FW7238/12
- 1 x US adapter
- 1 x UK adapter
- 1 x Key for closing and opening the box
- 1 x Prepaid pre-charged SIM card and 6 months access to the FALCOM web server for evaluation purposes *.
- 1 x Infosheet, contains all information needed to get started with DISCO-EVALKIT
(SIM card information, login data for accessing necessary online documentation and trace4you server frontend).
- 1 x Installation instruction sheet, contains necessary information about getting started with a DISCO device.
*Attention: The prepaid SIM card is not available for all countries. The 6 months access to the
FALCOM demo web server is not part of the FALCOM’s liabilities but a voluntary offer free-ofcharge for DISCO-B4-EVALKIT buyers for evaluation and demonstration purposes and without responsibility.
NOTES
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 32 of 38
Document revision 2.0.5 - Modified on 13/01/2015
PRODUCT NAME
EVALKITS
DISCO-B5-MAGNET-EVALKIT
OPTIONS
None
DESCRIPTION
Complete plug and play evaluation system for the DISCO-B5-MAGNET device. RoHS compliant. This delivery consists of 1 box:
Package
contents
:
1 x DISCO-B5-MAGNET unit shipped pre-configured.
1 x Programming and power/charge cable with RS-232 serial port and Wall
Adapter Power Supply.
1 x Key for closing and opening the box.
1 x Prepaid pre-charged SIM card and 6 months access to the FALCOM web server for evaluation purposes *.
1 x Infosheet, contains all information needed to get started with DISCO-B5-
MAGNET-EVALKIT (SIM card information, login data for accessing necessary online documentation and trace4you server frontend).
1 x Installation instruction sheet, contains necessary information about getting started with a DISCO-B5-MAGNET device.
*Attention: The prepaid SIM card is not available for all countries. The 6 months access to the
FALCOM demo web server is not part of the FALCOM’s liabilities but a voluntary offer free-ofcharge for DISCO-B5-MAGNET-EVALKIT buyers for evaluation and demonstration purposes and without responsibility.
NOTES
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 33 of 38
PRODUCT NAME
EVALKITS
MAMBO2-B6-EVALKIT
OPTIONS
None
Document revision 2.0.5 - Modified on 13/01/2015
DESCRIPTION
Complete plug and play evaluation system for the MAMBO2-B6 device. RoHS compliant. This delivery consists of 1 box:
Package
contents
:
- 1 x MAMBO2-B6 unit shipped pre-configured
- 1 x Docking station, consists of base plate, holding cradle, USB-to-mini-USB cable
- 1 x AC/DC removable adapter (9V output) for different plugs with USB port
- 1 x EU plug
- 1 x US plug
- 1 x UK plug
- 1 x Key for closing and opening the box
- 1 x Car mounting kit, consits of vehicle suction foot, holding frame, base plate,
USB-to-mini-USB power cable, car charger with USB port, 4 x screws and 1 x allen key.
- 1 x Prepaid pre-charged SIM card and 6 months access to the FALCOM web server for evaluation purposes *.
- 1 x Infosheet, contains all information needed to get started with MAMBO2-B6-
EVALKIT (SIM card information, login data for accessing necessary online documentation and trace4you server frontend).
*Attention: The prepaid SIM card is not available for all countries. The 6 months access to the
FALCOM demo web server is not part of the FALCOM’s liabilities but a voluntary offer free-ofcharge for MAMBO2-B6-EVALKIT buyers for evaluation and demonstration purposes and without responsibility.
NOTES
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 34 of 38
Document revision 2.0.5 - Modified on 13/01/2015
ORDERING PROCESS
In order to process your PO without any further inquiries, please provide the following information:
Order Information
[COMPANY NAME]
[CUSTOMER P.O. NO]
[DATE OF P.O.]
[BILLING ADDRESS]
[VAT-NO]
[SHIPPING ADDRESS]
[INCOTERM]
[PREFERRED CARRIER]
[CARRIER ACCOUNT-NO]
[CONTACT DETAILS]
[PRODUCT NAME]
[QUANTITY]
[PRICE]
[REQUESTED DELIVERY DATE]
Description
Depending of the INCOTERM
Details of the recipient at the delivery address incl. name and phone number.
As stated in Ordering Guide, including options.
See price list or SQ.
Optional.
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 35 of 38
Document revision 2.0.5 - Modified on 13/01/2015
USED ABBREVIATIONS
GPRS
IGN
SPK
MIC
OUT
IN
TTL
EOL
ODM
MOQ
LTB
LTD
NPI
JAZZx
GSM
GPS
GLONASS
SIM
LED
RX
TX
Abbreviation Meaning
End Of Life
Original Design Manufacturer
Minimum Order Quantity
Last Time Buy
Last Time Delivery
USB
SPI
RS-232
CAN
FMS
New Product Introduction
JAZZ1 and JAZZ2
OBD-II
I/O
Global Standard for Mobile Communications
VDC
Global Positioning System
TFT
Global Navigation Satellite System (Russia)
Subscriber Identification Module
SD
CPU
General Packet Radio Service
Ignition
Speaker
Microphone
Digital Output
Digital Input
Transistor-Transistor-Logic
RAM
DDR
SPP
RFID
OLED
GUI
AES
Light-Emitting Diode
Receive direction
Transmit direction
SQ
Abbreviation Meaning
Universal Serial Bus
Serial Peripheral Interface
Recommended Standard 232 (EIA standard for transmitting serial data)
Controller Area Network
Fleet Management Systems
On Board Diagnostics, 2nd generation
Multi function input/output
Volts Direct Current
Thin Film Transistor
Secure Digital
Central Processing Unit
Random Access Memory
Double Data Rate
Serial Port Profile (Bluetooth)
Radio-Frequency IDentification
Organic Light-Emitting Diode
Graphical User Interface
Advanced Encryption Standard
Special quote.
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 36 of 38
Document revision 2.0.5 - Modified on 13/01/2015
FALCOM GmbH products are RoHS conform
FALCOM Wireless Communications GmbH
Gewerbering 6
98704 Langewiesen
Germany
Phone: +49 (0)3677 8042-0
Fax: +49 (0)3677 8042-256
e-mail: [email protected]
Web: www.falcom.de
Terms & Conditions
General Terms:
See our general terms & conditions on following weblink: http://www.falcom.de/contact/
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 37 of 38
Document revision 2.0.5 - Modified on 13/01/2015
2.0.4
2.0.3
2.0.2
2.0.1
2.0.0
1.1.1
1.0.1
1.0.0
Document history:
Version Changes
2.0.5
- Updated: FOX3-STARTERKIT contents.
- Extended: FOX3-EVALKIT contents - CA38 cable added.
- Changed: PAID-Features to PREMIUM FEATURES .
- Changed Hint : IOBOX-MINI can be used with FOX-IN/EN and FOX3.
- Removed the accessory "
Leather-Bag" for MAMBO2.
- Added CA68 (main port installation cable 8pin connector with open ends) for FOX3
- Added STARTERKIT for FOX3
- Added paid-features: EXTENDED-GEOFENCES, EXTENDED-ALARMS
- Added: FOX3 and FOX3-EVALKIT
- Added: Premium-features for FOX3 (only): CAN-INTERFACE & RS-485-INTERFACE
- Added DISCO-B5-MAGNET-EVALKIT (this version is still not released)
- JAZZ-2 is offered without camera
- Initial version
Modified
18/02/2015
08/12/2014
24/10/2014
06/10/2014
30/09/2014
19/09/2014
09/01/2014
01/07/2013
14/06/2011
© FALCOM GmbH 2014 | Subject to change without prior notification Page: 38 of 38
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project