I-7530 Intelligent RS-232 to CAN converter
Intelligent RS-232 to CAN converter
I-7530
The PC can be the CAN host, monitor or HMI to access/control the CAN device through the CAN
network by the I-7530 Converter. The programmable RS-232 device (For example: PACs of ICP DAS)
can use the serial port to connect to the CAN network via the I-7530 module. The I-7530 is designed
to unleash the power of CAN bus via RS-232 communication method. It accurately converts
messages between CAN and RS-232 networks. This module let you communicate with CAN devices
easily from any PC or devices with RS-232 interface.
CAN Monitor & Data log Tools
Compatible with CAN specification 2.0A and B
Fully compatible with ISO 11898-2 standard
Support various bauds from 10K bps to 1M bps
Jumper for 120 Ω terminator resistor
Software configurable CAN and RS-232
communication parameters
1000 frames in CAN received buffer, 900 frames in
RS-232 received buffer
Watchdog inside
Support transparent communication mode
Show CAN messages by hex or decimal format
CAN messages with timestamp
Easy-to-use data logger for the diagnosis of the CAN
networks and recording of the received data
Send the predefined CAN messages manually or
cyclically
Utility Features
Wire Assignments
CAN bus baud rate configuration
CAN acceptance filter configuration
CAN 2.0A or 2.0B specific selection
Serial COM baud rate and data bit setting
Serial COM command error response selection
Utility tool for transmitting / receiving CAN messages
1-03
CAN Interface
Controller
Transceiver
Channel number
Connector
Baud Rate (bps)
Transmission Distance (m)
Isolation
Terminator Resistor
Specification
Receive Buffer
Microprocessor inside with 20 MHz
NXP 82C250
1
9-pin male D-Sub (CAN_L, CAN_SHLD, CAN_H, N/A for others)
10 k, 20 k, 50 k, 125 k, 250 k, 500 k, 800 k, 1 Mbps
Depend on baud rate (for example, max. 1000 m at 50 kbps )
3000 VDC for DC-to-DC, 2500 Vrms for photo-couple
Selectable 120 Ω terminator resistor by jumper
ISO-11898-2, CAN 2.0A and CAN 2.0B
1000 data frames
UART Interface
COM
COM Connector
Baud Rate (bps)
Data bit
Stop bit
Parity
Receive Buffer
RS-232
9-pin female D-Sub (DCE: TxD, RxD, GND, N/A for others )
110, 150, 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps
5, 6, 7, 8
1, 2
None, Even, Odd
900 data frames
LED
Round LED
ON LED: Power and Data Flow; ERR LED: Error
Power
Protection
Power Consumption
Power reverse polarity protection, Over-voltage brown-out protection
1W
Mechanism
Installation
Dimensions
DIN-Rail
118mm x 72mm x 33mm
Environment
Operating Temp.
Storage Temp.
Humidity
-25 ~ 75 ℃
-40 ~ 80 ℃
5 ~ 95% RH, non-condensing
Applications
Ordering Information
I-7530-G
Intelligent RS-232 to CAN converter
I-7530-G CR
Intelligent RS-232 to CAN converter (RoHS)
1-04
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement