wiki:suppliers:micronet:dokument:sp6005p4_qig

wiki:suppliers:micronet:dokument:sp6005p4_qig
Specifications
Note:
1. Ports 1 to 4 are used for connecting to PD or PoE splitter for
1. end devices.
Module
SP6005P4
2. For high power applications, the PD or PoE splitter has to be
1. compliant with pre-802.3at standard.
Standards
IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX
3. Port 5 is the RJ-45 uplink port that connects with non-PoE
1. Device.
Hardware
1 x RJ-45 ports of 10/100M (#5)
IEEE 802.3af / pre-802.3at Power over Ethernet
4 x RJ-45 PoE ports of 10/100M (#1 - #4)
MAC address: 2K
For cable selection, refer to the following table:
Buffer memory: 512KB
Max. Length
Network Speed
Cable Type
10M
Cat. 3,4,5,5e UTP/STP 100 meters
Auto MDI/MDI-X for 10/100M ports
100M
Cat. 5,5e UTP/STP
100 meters
Max. 61.6W system feeding power
Features
Auto negotiation for 10/100M ports
Note:
Deliver high power 48/30/20W for 1/2/3 PDs
To prevent costly equipment damage and downtime, please
consider installing a surge suppression device or a UPS (Uninterrupted Power Supply).
OVP (Over Voltage Protection)
OCP (Over Current Protection)
OTP (Over Temperature Protection)
SCP (Short Circuit Protection)
Surge protection
LED indicators for PoE activity
Power Supply DC 48V, 1.25A
Environment
Operating Temperature: 0 55 degree C
Storage Temperature: -20 90 degree C
Relative Humidity: 10 to 90%
Dimension
120 x 90 x 28 (mm)
Emission
CE
5
6
FCC Certifications
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and radiates radio frequency energy and, if
not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at own expense. This
device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received; including interference that may cause
undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to
electromagnetic compatibility of the essential protection
requirement of Council Directive 89/336/EEC on the
approximation of the laws of the Member States. Company has
an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date.
Please check with your local distributors for the latest
information. No part of this document can be copied or
reproduced in any form without written consent from the
company.
P/N: 2300-0580
WEEE Directive & Product Disposal
At the end its serviceable life ,this product should not be treated
as household or general waste. It should be handed over to the
applicable collection point for the recycling of electrical and
electronic equipment, or returned to the supplier for disposal.
7
Quick Installation Guide
5-Port 10/100M PoE Switch, 4 PoE Ports
Model No.: SP6005P4
Web: www.micronet.com.tw
Introduction
Tour of the System
The SP6005P4 supports IEEE 802.3af and pre-802.3at standards
for Power over Ethernet (PoE) with the maximum power delivery
up to 48 Watts. That makes it suitable to various applications that
demand for remote power feeding and meet high level requirement
for power. In addition, the SP6005P4 is equipped with DIP switch
for per-port PoE enabled/disabled. It effectively helps allocate
power for connected devices and enhances network management.
Front Panel
Key Features
Back Panel
• Compliant with IEEE 802.3af and pre-802.3at standards
RJ-45 PoE ports and work with DC48V/1.25A adaptor
LED indicators, dip switch and one uplink port
• Supports Power over Ethernet on 4 RJ-45 ports of 10/100M
• Provides 61.6W (max) feeding power to 4 PDs: 15.4W for each
• Able to delivers high power to 1/2/3 PDs: 48/30/20W for each
• Supports power protection as OVP (Over Voltage Protection),
• OCP (Over Current Protection), OTP (Over Temperature
• Protection), and SCP (Short Circuit Protection)
LED Indicator
• Supports robust surge protection
For definitions of LED indicators, please refer to the following
table:
• Equipped with DIP switch for per-port PoE enabled/disabled
• LED indicators for PoE activity
LED
Status
Operation
POWER
On/Green
Power is on
Off
Power is off
On/Green
The Ethernet port is connecting
with the device.
Blink/Green
Receiving or transmitting data.
Off
No device attached.
On/Green
PoE port is active.
Off
PoE port is not active.
Package Contents
Before you start installing SP6005P4, please verify the following
package contents:
LINK
• SP6005P4 10/100M PoE Switch
• Quick Installation Guide
PoE
• AC/DC Power Adaptor
• Power Cord
1
2
Dip Switch Configuration
Hardware Installation
The DIP switch can be switched 'ON' or 'OFF' anytime for PoE
function enabled/disabled.
The setup of the switch can be performed using the following
steps:
Step 1: Connect the AC Power Adaptor to SP6005P4 and then
Step 1: to a power outlet.
Step 2: Enable PoE port manually with dip switch 'On'.
OFF
Step 3: Connect a RJ-45 Ethernet cable from IEEE802.3afStep 1: compliant devices (PD) to an available PoE port of
Step 1: SP6005P4.
ON
1
3
2
4
PoE Control
Number of Enabled
PoE Ports
Maximal power on
Each PoE Port (Watts)
1
2
3
4
*48
*30
*20
15.4
Note:
1. It is suggested that the dip switch is set ready before the PoE
1. port is connected.
2. (*) The SP6005P4, with pre-802.3at compliant, provides
1. Extended power levels 48/30/20 watts for higher power
1. applications.
3
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising