Certificate CB Test Report "M,M1,M3"   ( PDF 2,79Mb )

Certificate CB Test Report "M,M1,M3"   ( PDF 2,79Mb )
Test Report issued under the responsibility of:
TEST REPORT
IEC 60335-2-80
Safety of household and similar electrical appliances
Part 2 : Particular requirements for fans
Report Reference No. ...........................:
28210042 001
Date of issue...........................................:
06-09-2010
Total number of pages............................:
85
CB Testing Laboratory .........................:
MEEI Kft.
Address ..................................................:
H-1132 Budapest, Váci út 48. a-b. Hungary
Applicant’s name ..................................:
Ventilation Systems JSC
Address ..................................................:
1, Mikhaila Kotzubinskiego St., Kiev, UA-01030, Ukraine
Test specification:
Standard ............................................:
IEC 60335-2-80:2002 (Second edition) + A1:2004 +A2:2008 in conj. With
IEC 60335-1:2001 (Fourth Edition) + A1:2004 + A2:2006
and the followings in attachment 1:EN 60335-2-80: 2003 +A1 : 2004 +
A2 :2009 ; EN 60335-1: 2002+A1: 2004 + A11: 2004 + A2: 2006 + A12: 2006
+ A13: 2008 ; EN 62233: 2008
Test procedure .......................................:
CB
Non-standard test method. .....................:
N/A
Test Report Form No. ...........................:
IEC60335_2_80C
TRF Originator ........................................:
KEMA Quality B.V.
Master TRF.............................................:
Dated 2008-12
Copyright © 2008 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE),
Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is
acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume
liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and
context.
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB Scheme
procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended
to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
Test item description .....................:
Fans
Trade Mark .......................................:
VENTS
Manufacturer ....................................:
Ventilation Systems JSC 1, Mikhaila Kotzubinskiego St., Kiev,
UA-01030, Ukraine
Model/Type reference.......................:
VENTS xxx Myuuu z
Ratings .............................................:
AC 220-240V, 50 Hz, 0 – 45 °C, Class II, IP 34
6, 9, 14, 16, 20, 24, 30 W; for details see ‘model list’ on pages 3 – 9.
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 3 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
Summary of testing: Tests were conducted on models: VENTS 100 MVTH, VENTS 125 M1 and VENTS 150
M3TP Q
During the documentation check the English User’s Manual was evaluated.
Factory location: 36, 40-Richchya Zhovtnya Str. Boyarka 08150, Kiev Region, Ukraine.
The following standard amendments are added in the Attachment 1:
EN 60335-2-80: 2003 +A1: 2004 + A2: 2009
EN 60335-1: 2002+A1: 2004 + A11: 2004 + A2: 2006 + A12: 2006 + A13: 2008; EN 62233: 2008
Attachments: 1: Standard amendments TRF (8 pages)
2: Measuring equipment list (1 page)
This Test Report consists of two parts:
-
first part contains requirements of IEC 60335-2-80:2002 incl. A1:2004, A2:2008 in conjunction with
IEC 60335-1:2001, incl. A1:2004, A2:2006;
-
second part (1. attachment) contains requirements of EN 60335-2-80: 2003 +A1: 2004 + A2 :2009;
EN 60335-1: 2002+A1: 2004 + A11: 2004 + A2: 2006 + A12: 2006 + A13: 2008; EN 62233: 2008.
Model list, technical data:
Fan type
VENTS 100 M
VENTS 100 MV
VENTS 100 MT
VENTS 100 MTH
VENTS 100 MVT
VENTS 100 MVTH
VENTS 100 MTP
VENTS 100 M1
VENTS 100 M1V
VENTS 100 M1T
VENTS 100 M1TH
VENTS 100 M1VT
VENTS 100 M1VTH
VENTS 100 M1TP
VENTS 100 M2
VENTS 100 M2V
VENTS 100 M2T
VENTS 100 M2TH
VENTS 100 M2VT
VENTS 100 M2VTH
VENTS 100 M2TP
VENTS 100 M3
VENTS 100 M3V
VENTS 100 M3T
TRF No. IEC60335_2_80C
Rated power
[W]
Motor type
14
BL 58-12A01
Motor manufacturer
Hunan Keli Motor Ltd.
TRF originator: KEMA
Page 4 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
VENTS 100 M3TH
VENTS 100 M3VT
VENTS 100 M3VTH
VENTS 100 M3TP
VENTS 100 M press
VENTS 100 MV press
VENTS 100 MT press
VENTS 100 MTH press
VENTS 100 MVT press
VENTS 100 MVTH press
VENTS 100 MTP press
VENTS 100 M1 press
VENTS 100 M1V press
VENTS 100 M1T press
VENTS 100 M1TH press
VENTS 100 M1VT press
VENTS 100 M1VTH press
VENTS 100 M1TP press
VENTS 100 M2 press
VENTS 100 M2V press
VENTS 100 M2T press
VENTS 100 M2TH press
VENTS 100 M2VT press
VENTS 100 M2VTH press
VENTS 100 M2TP press
VENTS 100 M3 press
VENTS 100 M3V press
VENTS 100 M3T press
VENTS 100 M3TH press
VENTS 100 M3VT press
VENTS 100 M3VTH press
VENTS 100 M3TP press
VENTS 100 M Q
VENTS 100 MV Q
VENTS 100 MT Q
VENTS 100 MTH Q
VENTS 100 MVT Q
VENTS 100 MVTH Q
VENTS 100 MTP Q
VENTS 100 M1 Q
VENTS 100 M1V Q
VENTS 100 M1T Q
VENTS 100 M1TH Q
VENTS 100 M1VT Q
VENTS 100 M1VTH Q
VENTS 100 M1TP Q
VENTS 100 M2 Q
VENTS 100 M2V Q
TRF No. IEC60335_2_80C
Result - Remark
Verdict
14
BL 58-12A01.
Hunan Keli Motor Ltd
16
6
BL 58-12Y03
CIXI CITI YIXIONG
ELECTROMOTOR
FACTORY
TRF originator: KEMA
Page 5 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
VENTS 100 M2T Q
VENTS 100 M2TH Q
VENTS 100 M2VT Q
VENTS 100 M2VTH Q
VENTS 100 M2TP Q
VENTS 100 M3 Q
VENTS 100 M3V Q
VENTS 100 M3T Q
VENTS 100 M3TH Q
VENTS 100 M3VT Q
VENTS 100 M3VTH Q
VENTS 100 M3TP Q
VENTS 100 M turbo
VENTS 100 MV turbo
VENTS 100 MT turbo
VENTS 100 MTH turbo
VENTS 100 MVT turbo
VENTS 100 MVTH turbo
VENTS 100 MTP turbo
VENTS 100 M1 turbo
VENTS 100 M1V turbo
VENTS 100 M1T turbo
VENTS 100 M1TH turbo
VENTS 100 M1VT turbo
VENTS 100 M1VTH turbo
VENTS 100 M1TP turbo
VENTS 100 M2 turbo
VENTS 100 M2V turbo
VENTS 100 M2T turbo
VENTS 100 M2TH turbo
VENTS 100 M2VT turbo
VENTS 100 M2VTH turbo
VENTS 100 M2TP turbo
VENTS 100 M3 turbo
VENTS 100 M3V turbo
VENTS 100 M3T turbo
VENTS 100 M3TH turbo
VENTS 100 M3VT turbo
VENTS 100 M3VTH turbo
VENTS 100 M3TP turbo
VENTS 125 M
VENTS 125 MV
VENTS 125 MT
VENTS 125 MTH
VENTS 125 MVT
VENTS 125 MVTH
VENTS 125 MTP
VENTS 125 M1
TRF No. IEC60335_2_80C
Result - Remark
Verdict
6
BL 58-12Y03
CIXI CITI YIXIONG
ELECTROMOTOR
FACTORY
16
BL 58-16A01
Hunan Keli Motor Ltd.
16
BL 58-16A01
Hunan Keli Motor Ltd.
TRF originator: KEMA
Page 6 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
VENTS 125 M1V
VENTS 125 M1T
VENTS 125 M1TH
VENTS 125 M1VT
VENTS 125 M1VTH
VENTS 125 M1TP
VENTS 125 M2
VENTS 125 M2V
VENTS 125 M2T
VENTS 125 M2TH
VENTS 125 M2VT
VENTS 125 M2VTH
VENTS 125 M2TP
VENTS 125 M3
VENTS 125 M3V
VENTS 125 M3T
VENTS 125 M3TH
VENTS 125 M3VT
VENTS 125 M3VTH
VENTS 125 M3TP
VENTS 125 M press
VENTS 125 MV press
VENTS 125 MT press
VENTS 125 MTH press
VENTS 125 MVT press
VENTS 125 MVTH press
VENTS 125 MTP press
VENTS 125 M1 press
VENTS 125 M1V press
VENTS 125 M1T press
VENTS 125 M1TH press
VENTS 125 M1VT press
VENTS 125 M1VTH press
VENTS 125 M1TP press
VENTS 125 M2 press
VENTS 125 M2V press
VENTS 125 M2T press
VENTS 125 M2TH press
VENTS 125 M2VT press
VENTS 125 M2VTH press
VENTS 125 M2TP press
VENTS 125 M3 press
VENTS 125 M3V press
VENTS 125 M3T press
VENTS 125 M3TH press
VENTS 125 M3VT press
VENTS 125 M3VTH press
VENTS 125 M3TP press
TRF No. IEC60335_2_80C
Result - Remark
16
BL 58-16A01
24
BL 58-16A01
Verdict
Hunan Keli Motor Ltd.
Hunan Keli Motor Ltd.
TRF originator: KEMA
Page 7 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
VENTS 125 M Q
VENTS 125 MV Q
VENTS 125 MT Q
VENTS 125 MTH Q
VENTS 125 MVT Q
VENTS 125 MVTH Q
VENTS 125 MTP Q
VENTS 125 M1 Q
VENTS 125 M1V Q
VENTS 125 M1T Q
VENTS 125 M1TH Q
VENTS 125 M1VT Q
VENTS 125 M1VTH Q
VENTS 125 M1TP Q
VENTS 125 M2 Q
VENTS 125 M2V Q
VENTS 125 M2T Q
VENTS 125 M2TH Q
VENTS 125 M2VT Q
VENTS 125 M2VTH Q
VENTS 125 M2TP Q
VENTS 125 M3 Q
VENTS 125 M3V Q
VENTS 125 M3T Q
VENTS 125 M3TH Q
VENTS 125 M3VT Q
VENTS 125 M3VTH Q
VENTS 125 M3TP Q
VENTS 125 M turbo
VENTS 125 MV turbo
VENTS 125 MT turbo
VENTS 125 MTH turbo
VENTS 125 MVT turbo
VENTS 125 MVTH turbo
VENTS 125 MTP turbo
VENTS 125 M1 turbo
VENTS 125 M1V turbo
VENTS 125 M1T turbo
VENTS 125 M1TH turbo
VENTS 125 M1VT turbo
VENTS 125 M1VTH turbo
VENTS 125 M1TP turbo
VENTS 125 M2 turbo
VENTS 125 M2V turbo
VENTS 125 M2T turbo
VENTS 125 M2TH turbo
VENTS 125 M2VT turbo
VENTS 125 M2VTH turbo
TRF No. IEC60335_2_80C
Result - Remark
Verdict
9
BL 58-16Y03
CIXI CITI YIXIONG
ELECTROMOTOR
FACTORY
24
BL 58-20A01
Hunan Keli Motor Ltd.
TRF originator: KEMA
Page 8 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
VENTS 125 M2TP turbo
VENTS 125 M3 turbo
VENTS 125 M3V turbo
VENTS 125 M3T turbo
VENTS 125 M3TH turbo
VENTS 125 M3VT turbo
VENTS 125 M3VTH turbo
VENTS 125 M3TP turbo
VENTS 150 M
VENTS 150 MV
VENTS 150 MT
VENTS 150 MTH
VENTS 150 MVT
VENTS 150 MVTH
VENTS 150 MTP
VENTS 150 M1
VENTS 150 M1V
VENTS 150 M1T
VENTS 150 M1TH
VENTS 150 M1VT
VENTS 150 M1VTH
VENTS 150 M1TP
VENTS 150 M2
VENTS 150 M2V
VENTS 150 M2T
VENTS 150 M2TH
VENTS 150 M2VT
VENTS 150 M2VTH
VENTS 150 M2TP
VENTS 150 M3
VENTS 150 M3V
VENTS 150 M3T
VENTS 150 M3TH
VENTS 150 M3VT
VENTS 150 M3VTH
VENTS 150 M3TP
VENTS 150 M press
VENTS 150 MV press
VENTS 150 MT press
VENTS 150 MTH press
VENTS 150 MVT press
VENTS 150 MVTH press
VENTS 150 MTP press
VENTS 150 M1 press
VENTS 150 M1V press
VENTS 150 M1T press
VENTS 150 M1TH press
VENTS 150 M1VT press
TRF No. IEC60335_2_80C
Result - Remark
Verdict
24
BL 58-20A01
Hunan Keli Motor Ltd.
24
BL 58-30A01
Hunan Keli Motor Ltd.
30
BL 58-30A01
Hunan Keli Motor Ltd.
TRF originator: KEMA
Page 9 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
VENTS 150 M1VTH press
VENTS 150 M1TP press
VENTS 150 M2 press
VENTS 150 M2V press
VENTS 150 M2T press
VENTS 150 M2TH press
VENTS 150 M2VT press
VENTS 150 M2VTH press
VENTS 150 M2TP press
VENTS 150 M3 press
VENTS 150 M3V press
VENTS 150 M3T press
VENTS 150 M3TH press
VENTS 150 M3VT press
VENTS 150 M3VTH press
VENTS 150 M3TP press
VENTS 150 M Q
VENTS 150 MV Q
VENTS 150 MT Q
VENTS 150 MTH Q
VENTS 150 MVT Q
VENTS 150 MVTH Q
VENTS 150 MTP Q
VENTS 150 M1 Q
VENTS 150 M1V Q
VENTS 150 M1T Q
VENTS 150 M1TH Q
VENTS 150 M1VT Q
VENTS 150 M1VTH Q
VENTS 150 M1TP Q
VENTS 150 M2 Q
VENTS 150 M2V Q
VENTS 150 M2T Q
VENTS 150 M2TH Q
VENTS 150 M2VT Q
VENTS 150 M2VTH Q
VENTS 150 M2TP Q
VENTS 150 M3 Q
VENTS 150 M3V Q
VENTS 150 M3T Q
VENTS 150 M3TH Q
VENTS 150 M3VT Q
VENTS 150 M3VTH Q
VENTS 150 M3TP Q
Result - Remark
Verdict
30
BL 58-30A01
Hunan Keli Motor Ltd.
20
BL 58-30Y03
CIXI CITI YIXIONG
ELECTROMOTOR
FACTORY
Models differ in model name, rated power, shape of enclosure, type of the motor, switch, motion sensor,
humidity sensor and timer.
All type: 220 – 240 V, 50 Hz, IP 34, Class II, 0 – 45 °C
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 10 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Tests performed (name of test and test clause):-
Result - Remark
Verdict
Testing location:
MEEI Kft.
H-1132 Budapest, Váci út 48. a-b. Hungary
Summary of compliance with National Differences: EU Group Differences and National Differences of
DE have been tested and found to be complied with. (See in attachment 2)
Copy of marking plate:
Design of rating label of other models is identical to the above except for type designation, rated power and
flow rate
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 11 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
Test item particulars .................................................. :
Classification of installation and use ............................ : Class II
Supply Connection........................................................ : Permanent connection, supply cord is not provided
...................................................................................... : ...................................................................................... : Possible test case verdicts:
- test case does not apply to the test object..................: N/A
- test object does meet the requirement .......................: P(Pass)
- test object does not meet the requirement .................: F(Fail)
Testing ..........................................................................:
Date of receipt of test item ............................................: 14-07-2010
Date (s) of performance of tests ...................................: 19-08-2010 – 06-09-2010
General remarks:
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and
appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory.
"(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a comma (point) is used as the decimal separator.
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 12 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
General product information: The fans are designed for ventilation of domestic and similar purposes and for
continuous operation. Meaning of characters in type references:
VENTS xxx Myuuu z
‘VENTS’: trade mark
’xxx’: the diameter of the duct [mm].It can be: 100; 125; 150.
- ‘My’: fan type. It can be M, M1, M2, M3. (They differ in shape of enclosure)
-
-
‘uuu’: it can be blank, V, T, TH, VT, VTH, TP.
T:
supplied with timer
V:
supplied with switch
H:
supplied with humidity relay
P:
supplied with motion sensor
‘z’: it can be blank, Q, turbo, press
Q:
turbo:
press:
quiet operation motor
motor with increased power is installed
increased press
Possible variants can be seen in table of model list, on pages 3 – 9.
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 13 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
5
GENERAL CONDITIONS FOR THE TESTS
P
Tests performed according to cl. 5, e.g. nature of
supply, sequence of testing, etc.
P
5.7
Result - Remark
Verdict
N/A
Fans to be used in tropical climates, the tests of
clause 10,11 and 13 are carried out at 40 °C +/- 2 °C
(IEC 60335-2-80)
Fans marked with ambient operating temperature,
the tests of clause 10, 11 and 13 are carried out at
marked value +/- 2 °C (IEC 60335-2-80/A1)
45 °C
P
6
CLASSIFICATION
6.1
Protection against electric shock:
Class 0, 0I, I, II, III ....................................................:
II.
P
6.101
Classification to climatic conditions : temperature
climates, tropical climates (IEC 60335-2-80)
For temperate climate.
P
6.2
Protection against harmful ingress of water
IP X4
P
7
MARKING AND INSTRUCTIONS
7.1
Rated voltage or voltage range (V) ..........................:
220-240 V
P
Nature of supply........................................................:
~
P
Rated frequency (Hz) ...............................................:
50 Hz
P
Rated power input (W): ............................................:
6, 9, 14, 16, 20, 24, 30 W for
details see ‘model list’ on
pages 3 - 9
P
Rated current (A) .....................................................:
Rated power stated.
Manufacturer's or responsible vendor's name,
trademark or identification mark...............................:
VENTS
P
Model or type reference............................................:
See copy of marking plate.
P
Symbol 5172 of IEC 60417, for Class II appliances
See copy of marking plate.
P
IP number, other than IPX0......................................:
IP 34
See copy of marking plate.
P
For tropical climates marked with letter T
(IEC 60335-2-80)
Not for tropical climates.
N/A
0 – 45 °C
Fans intended for operation in location where the
See copy of marking plate.
local temperature exceeds 40 °C shall be marked
with the ambient operating temperature. (IEC 603352-80/A1)
7.2
Warning for stationary appliances for multiple supply
Warning placed in vicinity of terminal cover
TRF No. IEC60335_2_80C
One supply.
N/A
P
N/A
N/A
TRF originator: KEMA
Page 14 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
7.3
Range of rated values marked with the lower and
upper limits separated by a hyphen
220-240 V~
See copy of marking plate.
P
Different rated values marked with the values
separated by an oblique stroke
N/A
7.4
Appliances adjustable for different rated voltages, the Not adjustable.
voltage setting is clearly discernible
N/A
7.5
Appliances with more than one rated voltage or one
or more rated voltage ranges, marked with rated
input or rated current for each rated voltage or range,
unless
N/A
the power input is related to the arithmetic mean
value of the rated voltage range (IEC 60335-1/A2)
Difference is less than 10%
P
N/A
Relation between marking for upper and lower limits
of rated power input or rated current and voltage is
clear
P
7.6
Correct symbols used
7.7
Connection diagram fixed to appliances to be
connected to more than two supply conductors and
appliances for multiple supply
N/A
7.8
Except for type Z attachment, terminals for connection to the supply mains indicated
as follows:
N/A
- marking of terminals exclusively for the neutral
conductor (N)
N/A
- marking of protective earthing terminals (symbol
5019 of IEC 60417)
Class II
N/A
- marking not placed on removable parts
N/A
7.9
Marking or placing of switches which may cause a
hazard
N/A
7.10
Indications of switches on stationary appliances and
controls on all appliances by use of figures, letters or
other visual means ...................................................:
-
N/A
The figure 0 indicates only OFF position, unless no
confusion with the OFF position
N/A
7.11
Indication for direction of adjustment of controls
N/A
7.12
Instructions for safe use provided
P
- the appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction. (IEC 60335-1/A2)
P
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 15 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
P
- Children should be supervised to ensure that they
do not play with the appliance. (IEC 60335-1/A2)
For the guards have to be removed purpose for cleaning should: (IEC 60335-2-80/A1)
Ensure that the fan is switched off from the supply
mains before removing the guard.
No guard
N/A
N/A
7.12.1
Sufficient details for installation supplied
P
7.12.2
User’s Manual “Preparation to
Stationary appliances not fitted with means for
device operation” states the
disconnection from the supply mains having a
necessary disconnection
contact separation in all poles that provide full
disconnection under overvoltage category III, the
instructions state that means for disconnection must
be incorporated in the fixed wiring in accordance with
the wiring rules
P
7.12.3
Insulation of the fixed wiring in contact with parts
exceeding 50 K during clause 11; instructions stating
that the fixed wiring must be protected
N/A
7.12.4
Instructions for built-in appliances:
N/A
- dimensions of space
N/A
- dimensions and position of supporting means
N/A
- distances between parts and surrounding structure
N/A
- dimensions of ventilation openings and
arrangement
N/A
- connection to supply mains and interconnection of
separate components
N/A
- plug accessible after installation, unless
N/A
a switch complying with 24.3
N/A
Replacement cord instructions, type X attachment
with a specially prepared cord
N/A
Replacement cord instructions, type Y attachment
N/A
Replacement cord instructions, type Z attachment
N/A
7.12.5
7.12.6
Instructions for heating appliances incorporating a
non-self-resetting thermal cut-out that is reset by
disconnection the supply mains contains the
warning (IEC 60335-1, A1)
7.12.7
The instructions for fixed appliances shall state how
the appliance is to be fixed to its support
(IEC 60335-1, A1)
TRF No. IEC60335_2_80C
No heating appliances.
N/A
P
TRF originator: KEMA
Page 16 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
7.12.8
The instructions for appliances connected to the
water mains shall state:
- max. inlet water pressure
- min. inlet water pressure (if necessary for correct
operation (IEC 60335-1, A1)
7.13
Instructions and other texts in an official language
7.14
Marking clearly legible and durable
P
7.15
Marking on a main part
P
Marking clearly discernible from the outside, if
necessary after removal of a cover
Result - Remark
Verdict
N/A
English and German provided.
Marking label repeated inside
too.
P
P
For portable appliances, cover can be removed or
opened without a tool
N/A
For stationary appliances, name, trademark or
identification mark and model or type reference
visible after installation
N/A
For fixed appliances, name, trademark or
identification mark and model or type reference
visible after installation according to the instructions
P
Indications for switches and controls placed on or
near the components. Marking not on parts which
can be positioned or repositioned in such a way that
the marking is misleading
N/A
7.16
Marking of a possible replaceable thermal link or fuse Non-replaceable thermal link
link clearly visible with regard to replacing the link
provided.
N/A
8
PROTECTION AGAINST ACCESS TO LIVE PARTS
P
8.1
Adequate protection against accidental contact with
live parts
P
8.1.1
Requirement applies for all positions, detachable
parts removed
P
Insertion or removal of lamps, protection against
contact with live parts of the lamp cap
N/A
8.1.2
Use of test probe B of IEC 61032: no contact with live
parts
P
Add NOTE 2 ”Without appreciable force” is
considered to be a force not exceeding 1 N (IEC
60335-1/A2)
P
Use of test probe 13 of IEC 61032 through openings
in class 0 appliances and class II appliances/
constructions: no contact with live parts
Test probe 13 also applied through openings in
earthed metal enclosures having a non-conductive
coating: no contact with live parts
TRF No. IEC60335_2_80C
No contact
P
N/A
TRF originator: KEMA
Page 17 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
Add NOTE 2 ”Without appreciable force” is
considered to be a force not exceeding 1 N (IEC
60335-1/A2)
8.1.3
8.1.4
8.1.5
For appliances other than class II, use of test probe
41 of IEC 61032: no contact with live parts of visible
glowing heating elements
N/A
Add NOTE 2 ”Without appreciable force” is
considered to be a force not exceeding 1 N (IEC
60335-1/A2)
N/A
Accessible part not considered live if:
N/A
- safety extra-low arc. voltage: peak value not
exceeding 42.4 V
N/A
- safety extra-low o.k. voltage: not exceeding 42.4 V
N/A
- or separated from live parts by protective
impedance
N/A
If protective impedance: o.k. current not exceeding
2 am, and
N/A
arc. peak value not exceeding 0.7 am
N/A
- for peak values over 42.4 V up to and including
450 V, capacitance not exceeding 0,1 µF
N/A
- for peak values over 450 V up to and including
15 kV, discharge not exceeding 45 µC
N/A
-for voltages having a peak value over 15 kV, the
energy in the discharge shall not exceed 350 my
(IEC 60335-1/A2)
N/A
Live parts protected at least by basic insulation before installation or assembly:
- built-in appliances
- fixed appliances
- appliances delivered in separate units
8.2
P
P
N/A
P
N/A
Class II appliances and constructions constructed so
that there is adequate protection against accidental
contact with basic insulation and metal parts
separated from live parts by basic insulation only
P
Only possible to touch parts separated from live parts
by double or reinforced insulation
P
Remove the detachable parts for user maintenance
purpose, the basic insulation of internal wiring may
be touched provide the equivalent insulating of cords
complying with IEC 60227 or IEC 60245. (IEC 603352-80/A1)
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 18 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
10
POWER INPUT AND CURRENT
10.1
Power input at normal operating temperature, rated
voltage and normal operation not deviating from
rated power input by more than shown in table 1
Result - Remark
Verdict
P
(see appended table)
N/A
Test for an appliance with one or more rated voltage
ranges. (IEC 60335-1/A2)
10.2
Current at normal operating temperature, rated
voltage and normal operation not deviating from
rated current by more than shown in table 2
P
Rated current is not marked.
N/A
N/A
Test for an appliance with one or more rated voltage
ranges. (IEC 60335-1/A2)
11
HEATING
P
11.1
No excessive temperatures in normal use
P
11.2
Placing and mounting of appliance as described
P
11.3
Temperature rises, other than of windings,
determined by thermocouples
P
Temperature rises of windings determined by
resistance method, unless
P
the windings makes it difficult to make the necessary
connections
N/A
11.4
Heating appliances operated under normal operation at 1.15 times rated power input ...............................:
N/A
11.5
Motor-operated appliances operated under normal
254.4V (1.06x240V) was the
operation at most unfavourable voltage between 0.94 most unfavourable.
and 1.06 times rated voltage....................................:
11.6
Combined appliances operated under normal
operation at most unfavourable voltage between 0.94
and 1.06 times rated voltage....................................:
11.7
Operation duration corresponding to the most
unfavourable conditions of normal use
11.8
Temperature rises not exceeding values in table 3
P
N/A
P
(see appended tables)
P
Protective devices do not operate
P
Sealing compound does not flow out
P
For fans marked with operating temperature, the
temperature rise limit is reduced by the difference
between the marked value and 25°C. (IEC 60335-280/A1)
P
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 19 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
13
LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING
TEMPERATURE
13.1
Leakage current not excessive and electric strength
adequate
Heating appliances operated at 1.15 times rated
power input ...............................................................:
13.2
13.3
Result - Remark
Verdict
P
-
Motor-operated appliances and combined appliances 254.4 V (1.06x240 V)
supplied at 1.06 times rated voltage ........................:
N/A
Protective impedance and radio interference filters
disconnected before carrying out the tests
N/A
Leakage current measured by means of the circuit
described in figure 4 of IEC 60990
P
Leakage current measurements
(see appended table)
P
Electric strength tests according to table 4
(see appended table)
P
P
No breakdown during the tests
14
TRANSIENT OVERVOLTAGES
N/A
Appliances withstand the transient overvoltages to
which they may be subjected
N/A
Clearances are not less than
Clearances having a value less than specified in
table 16 subjected to an impulse voltage test, the test specified.
voltage specified in table 6
N/A
No flashover during the test, unless of functional
insulation
N/A
In case of flashover of functional insulation, the
appliance complies with clause 19 with the clearance
short circuited
N/A
15
MOISTURE RESISTANCE
P
15.1
Enclosure provides the degree of moisture protection
according to classification of the appliance
P
Compliance checked as specified in 15.1.1, taking
into account 15.1.2, followed by the electric strength
test of 16.3
P
No trace of water on insulation which can result in a
reduction of clearances and creepage distances
below values specified in clause 29
P
15.1.1
Appliances, other than IPX0, subjected to tests as
specified in IEC 60529..............................................:
Water valves containing live parts are subjected to
the tests for IPX7 appliances (IEC 60335-1/A1)
TRF No. IEC60335_2_80C
Tested for IPX4.
P
N/A
TRF originator: KEMA
Page 20 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
N/A
The outer part of fans to be installed in the external
structure is subjected to subclause 14.2.4(a) of IEC
60529. The outer part of fans is not to be installed in
the external structure is protected against the water.
(IEC 60335-2-80/A1)
The fans supplied as rated voltage with shutters or
similar devices being the open position. (IEC 603352-80/A1)
15.1.2
Tested for IPX4.
P
Hand-held appliance turned continuously through the
most unfavourable positions during the test
N/A
Built-in appliances installed according to the
instructions
N/A
Appliances placed or used on the floor or table
placed on a horizontal unperforated support
N/A
Appliances normally fixed to a wall and appliances
with pins for insertion into socket-outlets are mounted
on a wooden board
N/A
For IPX3 appliances, the base of wall mounted
appliances is placed at the same level as the pivot
axis of the oscillating tube
N/A
For IPX4 appliances, the horizontal centre line of the
appliance is aligned with the pivot axis of the
oscillating tube
P
For IPX4 appliances normally fixed to a ceiling are
mounted underneath a horizontal unperforated
support that prevents water spraying onto the top
surface (IEC 60335-1/A1)
N/A
P
However, for appliances normally used on the floor or
table, the movement is limited to two times 90° for a
period of 5 min, the support being placed at the level
of the pivot axis of the oscillating tube
15.2
Wall-mounted appliances, take into account the
distance to the floor stated in the instructions
N/A
Appliances with type X attachment fitted with a
flexible cord as described
N/A
Detachable parts tested as specified
N/A
Spillage of liquid does not affect the electrical
insulation
Appliances with type X attachment fitted with a
flexible cord as described
TRF No. IEC60335_2_80C
No spillage in normal condition.
N/A
N/A
TRF originator: KEMA
Page 21 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Verdict
Appliances incorporating an appliance inlet tested
with or without an connector, whichever is most
unfavourable
N/A
Detachable parts removed
N/A
Overfilling test with additional amount of
water, over a period of 1 min (l)................................:
15.3
Result - Remark
N/A
-
The appliance withstands the electric strength test of
16.3
N/A
No trace of water on insulation that can result in a
reduction of clearances and creepage distances
below values specified in clause 29
N/A
Appliances proof against humid conditions
48h, 95%, 25°C
P
Humidity test for 48 h in a humidity cabinet
P
The appliance withstands the tests of clause 16
P
16
LEAKAGE CURRENT AND ELECTRIC STRENGTH
16.1
Leakage current not excessive and electric strength
adequate
P
Protective impedance disconnected from live parts
before carrying out the tests
N/A
16.2
16.3
Single-phase appliances: test voltage 1.06 times
rated voltage .............................................................:
254.4V (1.06x240V)
P
Three-phase appliances: test voltage 1.06 times
rated voltage divided by √3.......................................:
-
Leakage current measurements
(see appended table)
P
Electric strength tests according to table 7
(see appended table)
P
N/A
P
No breakdown during the tests
17
OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS
N/A
No excessive temperatures in transformer or
associated circuits in event of short-circuits likely to
occur in normal use
N/A
Appliance supplied with 1.06 or 0.94 times rated
voltage and the most unfavourable short-circuit or
overload likely to occur in normal use applied .........:
-
N/A
Temperature rise of insulation of the conductors of
safety extra-low voltage circuits not exceeding the
relevant value specified in table 3 by more than 15 K
N/A
Temperature of the winding not exceeding the value
specified in table 8,
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 22 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
18
Requirement + Test
Result - Remark
Verdict
however limits do not apply to fail-safe transformers
complying with sub-clause 15.5 of IEC 61558-1
N/A
ENDURANCE
N/A
Requirements and tests are specified in part 2 when
necessary
N/A
19
ABNORMAL OPERATION
P
19.1
The risk of fire or mechanical damage under
abnormal or careless operation obviated
P
Electronic circuits so designed and applied that a
fault will not render the appliance unsafe
P
Appliances incorporating contactors or relays are
subjected to the test of 19.14
(IEC 60335-1/A2)
N/A
Fans incorporating shutters or similar subjected to
the test of cl. 19.101 (IEC 60335-2-80)
See cl. 19.101.
N/A
19.2
Test of appliance with heating elements with
restricted heat dissipation; test voltage (V): power
input of 0.85 times rated power input.......................:
-
N/A
19.3
Test of 19.2 repeated; test voltage (V): power input of 1.24 times rated power input....................................:
N/A
19.4
Test conditions as in cl. 11, any control limiting the
temperature during tests of cl. 11 short-circuited
N/A
19.5
Test of 19.4 repeated on Class 0I and I appliances
with tubular sheathed or embedded heating
elements. No short-circuiting, but one end of the
element connected to the elements sheath
N/A
The test repeated with reversed polarity and the other
end of the heating element connected to the sheath
N/A
The test is not carried out on appliances intended to
be permanently connected to fixed wiring and on
appliances where an all-pole disconnection occurs
during the test of 19.4
N/A
Appliances with PTC heating elements tested at
rated voltage, establishing steady conditions
N/A
The working voltage of the PTC heating element is
increased by 5% and the appliance is operated until
steady conditions are re-established. The voltage is
then increased in similar steps until 1.5 times working
voltage or until the PTC heating element ruptures
N/A
19.6
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 23 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
19.7
Stalling test by locking the rotor if the locked rotor
torque is smaller than the full load torque or locking
moving parts of other appliances
Locked rotor, motor capacitors open-circuited or
short-circuited, if required
Result - Remark
Verdict
P
N/A
No motor-capacitor
Locked rotor, capacitors open-circuited one at a time
N/A
Test repeated with capacitors short-circuited one at a
time, if required
N/A
Appliances with timer or programmer supplied with
rated voltage for each of the tests, for a period equal
to the maximum period allowed
N/A
P
Other appliances supplied with rated voltage for a
period as specified
Winding temperatures not exceeding values
specified in table 8
19.8
Three-phase motors operated at rated voltage with
one phase disconnected
19.10
Series motor operated at 1.3 times rated voltage for
1 min .........................................................................:
(see appended table)
N/A
N/A
-
N/A
During the test, parts not being ejected from the
appliance
19.11
P
Electronic circuits, compliance checked by evaluation
of the fault conditions specified in 19.11.2 for all
circuits or parts of circuits, unless they comply with
the conditions specified in 19.11.1
Appliances having a switch with an off position
obtained by electronic disconnection, or a switch
placing the appliance in a stand-by mode, subjected
to the tests of 19.11.4 :(IEC 60335-1/A2)
P
The most unfavourable case is
the permanent operation. It is
not dangerous.
N/A
Appliances incorporating an electronic circuit that
relies upon a programmable component to function
correctly are subjected to the test of 19.11.4.8,
unless:(IEC 60335-1/A2)
N/A
-restarting at any point in the operating cycle after
interruption of operation due to a supply voltage dip
will not result in a hazard. (IEC 60335-1/A2)
- the test is carried out after removal of all batteries
and other components intended to maintain the
programmable component supply voltage during
mains supply voltage dips, interruptions and
variations. (IEC 60335-1/A2)
N/A
TRF No. IEC60335_2_80C
N/A
TRF originator: KEMA
Page 24 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
19.11.1
Before applying the fault conditions a) to f) in 19.11.2, it is checked if circuits or parts of
circuit meet both of the following conditions:
P
- the electronic circuit is a low-power circuit, that is,
the maximum power at low-power points does not
exceed 15 W according to the tests specified
P
19.11.2
Result - Remark
Verdict
C2, C3, VD1, VD2 were shortcircuited;
- the protection against electric shock, fire hazard,
mechanical hazard or dangerous malfunction in other
parts of the appliance does not rely on the correct
functioning of the electronic circuit
P
Fault conditions applied one at a time, the appliance operated under conditions
specified in cl. 11, but supplied at rated voltage, the duration of the tests as specified:
P
N/A
a) short circuit of functional insulation if clearances or
creepage distances are less than the values
specified in 29
P
b) open circuit at the terminals of any component
c) short circuit of capacitors, unless they comply with
IEC 60384-14
C1 complies with IEC 60384-14.
(CKX type)
P
d) short circuit of any two terminals of an electronic
component, other than integrated circuits. This fault
condition is not applied between the two circuits of an
optocoupler
e) failure of triacs in the diode mode
19.11.3
P
N/A
No such triacs
f) failure of an integrated circuit. The possible
hazardous situations of the appliance are assessed
to ensure that safety does not rely on the correct
functioning of such a component
N/A
g) failure of an electronic power switching device in
a partial turn-on mode with loss of gate (base)
control. During this test, winding temperatures shall
not exceed the values given in 19.7. (IEC 603351/A2)
N/A
If the appliance incorporates a protective electronic
circuit which operates to ensure compliance with
clause 19, the relevant test is repeated with a single
fault simulated, as indicated in a) to f) of 19.11.2
No protective electronic circuit
N/A
During and after each test the following is checked:
N/A
- the temperature rise of the windings do not exceed
the values specified in table 8
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 25 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
- the appliance complies with the conditions specified
in 19.13
N/A
- any current flowing through protective impedance
not exceeding the limits specified in 8.1.4
N/A
If a conductor of a printed board becomes open-circuited, the appliance is considered
to have withstood the particular test, provided all three of the following conditions are
met:
N/A
- the material of the printed circuit board withstands
the burning test of annex E
N/A
- any loosened conductor does not reduce the
clearances or creepage distances between live parts
and accessible metal parts below the values
specified in cl. 29
N/A
- the appliance withstands the tests of 19.11.2 with
open-circuited conductor bridged
N/A
Protective electronic circuits are subjected to the
tests of clause 19.11.4.1 to 19.11.4.7
(IEC 60335-1, A1)
N/A
Appliances with a device with an off position
obtaining by electronic disconnection or that can be
placed in a stand-by mode, are subjected to the
tests of clause 19.11/4.1 to 19.11.4 7 (IEC 60335-1,
A1) (IEC 60335-1/A2)
N/A
19.11.4.1
The appliance is subjected to electrostatic
discharges in accordance with IEC 61000-4-2, test
level 4 (IEC 60335-1, A1)
N/A
19.11.4.2
The appliance is subjected to radiated fields in
accordance with IEC 61000-4-3, test level 3
(IEC 60335-1, A1)
N/A
19.11.4.3
The appliance is subjected to fast transient bursts in
accordance with IEC 61000-4-4, test level 3
(IEC 60335-1, A1)
N/A
19.11.4.4
The power supply terminals of the appliance are
subjected to voltage surges in accordance with IEC
61000-4-5, test level 3 (IEC 60335-1, A1)
N/A
19.11.4.5
The appliance is subjected to injected currents in
accordance with IEC 61000-4-6, test level 3
(IEC 60335-1, A1)
N/A
19.11.4.6
The appliance is subjected to the values specified
in Table 1 and Table 2 of IEC 61000-4-11, test level
Class 3. (IEC 60335-1/A2)
N/A
19.11.4
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 26 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
19.11.4.7
The appliance is subjected to mains signals in
accordance with IEC 61000-4-13, test level class 2
(IEC 60335-1, A1)
N/A
19.11.4.8
The appliance is supplied at rated voltage and
operated under normal operation. (IEC 60335-1/A2)
N/A
- after approximately 60 s, the power supply voltage
is reduced to a level such that the appliance ceases
to respond to user inputs or parts cease to operate,
whichever occurs first. Record the value of supply
voltage. (IEC 60335-1/A2)
-the voltage is then reduced to a value of
approximately 10 %. Holding at this value for
approximately 60 s and then increased to rated
voltage. The rate is approximately 10 V/s.
(IEC 60335-1/A2)
The appliance shall continue to either operate
normally or a manual operation shall be required to
restart it.(IEC 60335-1/A2)
If the safety of the appliance for any of the fault
conditions specified in 19.11.2 depends on the
operation of a miniature fuse-link complying with
IEC 60127, the test is repeated, measuring the
current flowing through the fuse-link; measured
current (A); rated current of the fuse-link (A):
During the tests the appliance does not emit flames,
molten metal, poisonous or ignitable gas in
hazardous amounts
Temperature rises not exceeding the values shown
(see appended table)
in table 9
Compliance with cl. 8 is not impaired (IEC 603351/A2)
Enclosures not deformed to such an extent that
compliance with cl. 8 is impaired
If the appliance can still be operated it complies with
20.2
N/A
19.12
19.13
Result - Remark
Verdict
N/A
N/A
N/A
P
P
P
P
N/A
Insulation, other than of class III appliance, withstand the electric strength test of 16.3,
the test voltage specified in table 4:
P
- basic insulation:
L/N and motor surface (1250V)
P
- supplementary insulation:
Motor surface and enclosure
wrapped into metal foil (1750V)
P
- reinforced insulation:
L/N and enclosure wrapped
into metal foil (3000V)
P
- functional insulation, the test voltage is twice the
working voltage. (IEC 60335-1/A2)
The appliance shall not undergo a dangerous
malfunction and there shall be no failure of
protective electronic circuits if the appliance is still
operable (IEC 60335-1, A1)
480 V
P
TRF No. IEC60335_2_80C
P
TRF originator: KEMA
Page 27 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
Appliances with an electronic switch in the off
position or in the stand-by mode shall not become
operable (IEC 60335-1, A1)
Appliances tested with an electronic switch in the off The most unfavourable case is
position, or in the stand-by mode, shall: (IEC
the permanent operation. It is
60335-1/A2)
not dangerous.
N/A
N/A
- not become operational, or
N/A
N/A
20
- if they become operational, not result in a
dangerous malfunction during or after the
tests of 19.11.4
Any contactor or relay contact that operates under
the conditions of Clause 11 is short-circuited.
(IEC 60335-1/A2)
Note: If a relay or contactor with more than one
contact is used, all contacts are short-circuited at
the same time. (IEC 60335-1/A2)
Fans incorporating shutters or similar that are
operated automatically are supplied at rated voltage
in the closed or open position, whichever is more
unfavourable (IEC 60335-2-80)
STABILITY AND MECHANICAL HAZARDS
20.1
Adequate stability
19.14
19.101
20.2
N/A
N/A
P
Appliance shall be installed
properly according to the
User’s Manual.
Tilting test through an angle of 10° (appliance placed
on an inclined plane/horizontal plane); appliance
does not overturn
Tilting test repeated on appliances with heating
elements, angle of inclination increased to 15°
Possible heating test in overturned position;
temperature rise does not exceed values shown in
table 9
Portable pedestal fans exceeding 1,7 m and
No such fan
exceeding 10 kg tested with a force of 40 N at 1,5 m
(IEC 60335-2-80)
Moving parts adequately arranged or enclosed as to
provide protection against personal injury
Protective enclosures, guards and similar parts are
non-detachable
Adequate mechanical strength and fixing of
protective enclosures
Self-resetting thermal cut-outs and overcurrent
No such cut-outs
protective devices not causing a hazard, by
unexpected reclosure
Not possible to touch dangerous moving parts with
test probe
TRF No. IEC60335_2_80C
N/A
No shutter
N/A
N/A
N/A
N/A
N/A
P
P
P
N/A
P
TRF originator: KEMA
Page 28 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
20.101
Fan blades, other than those for mounting at high
level, shall be guarded, unless ...............................
(IEC 60335-2-80)
Blades are guarded after the
installation according the
User’s Manual by the duct
21
MECHANICAL STRENGTH
P
Appliance has adequate mechanical strength and is
constructed as to withstand rough handling
No damage after three blows applied to various parts
of the enclosure, impact energy 0,5 ± 0,04 J
If necessary, supplementary or reinforced insulation
subjected to the electric strength test of 16.3
If necessary, repetition of groups of three blows on a
new sample
Accessible parts of solid insulation shall have
sufficient strength to prevent penetration by sharp
implements. The parts are scratched with a
hardened steel pin. After the test there shall be no
damage and the insulation shall withstand the tests
of clause 16.3 (IEC 60335-1, A1)
P
21.2
21.101
Fan guards are subjected to a push and pull force of
20 N. Dangerous moving parts are not accessible
(IEC 60335-2-80)
Verdict
P
P
N/A
N/A
P
Blades are guarded after the
installation according the
User’s Manual by the duct
P
The test probe is applied with a force not exceeding
5N. (IEC 60335-2-80/A2)
N/A
21.102
Ceiling fans have adequate strength. Load four times No such fans.
mass (.......) (IEC 60335-2-80)
N/A
22
CONSTRUCTION
P
22.1
Appliance marked with the first numeral of the IP
system, relevant requirements of IEC 60529 are
fulfilled
P
22.2
Stationary appliance: means to provide all-pole disconnection from the supply
provided, the following means being available:
P
N/A
- a supply cord fitted with a plug
- a switch complying with 24.3
No switch with all-pole
disconnection.
- a statement in the instruction sheet that a
Statement in the User’s
disconnection incorporated in the fixed wiring is to be Manual.
provided
- an appliance inlet
TRF No. IEC60335_2_80C
No appliance inlet.
N/A
P
N/A
TRF originator: KEMA
Page 29 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Single-pole switches and single-pole protective
devices that disconnect heating elements from the
supply mains in single-phase, permanently
connected class 0I appliances and class I appliances
shall be connected to the phase conductor. (IEC
60335-1/A2)
22.3
Appliance provided with pins: no undue strain on
socket-outlets
Verdict
N/A
No pins.
N/A
Applied torque not exceeding 0.25 Nm
N/A
Pull force of 50N to each pin after the appliance has
being placed in the heating cabinet; when cooled to
room temperature the pins are not displaced by more
than 1mm
N/A
Each pin subjected to a torque of 0.4Nm; the pins are
not rotating unless rotating does not impair
compliance with the standard
N/A
22.4
Appliance for heating liquids and appliance causing
undue vibration not provided with pins for insertion
into socket-outlets
N/A
22.5
No risk of electric shock when touching the pins of
the plug
N/A
22.6
Electrical insulation not affected by condensing water
or leaking liquid
N/A
Electrical insulation of Class II appliances not
affected in case of a hose rupture or seal leak
N/A
22.7
Adequate safeguards against the risk of excessive
pressure in appliances provided with steamproducing devices
N/A
22.8
Electrical connections not subject to pulling during
cleaning of compartments to which access can be
gained without the aid of a tool, and that are likely to
be cleaned in normal use
N/A
22.9
Insulation, internal wiring, windings, commutators
and slip rings not exposed to oil, grease or similar
substances
P
Adequate insulating properties of oil or grease to
which insulation is exposed
N/A
Location or protection of reset buttons of non-selfresetting controls is so that accidental resetting is
unlikely
N/A
22.10
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 30 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
It shall not be possible to reset voltage-maintained
non-self-resetting thermal cut-outs by the operation
of an automatic switching device (IEC 60335-1/A1)
22.11
Result - Remark
Verdict
N/A
Reliable fixing of non-detachable parts that provide
the necessary degree of protection against electric
shock, moisture or contact with moving parts
P
Obvious locked position of snap-in devices used for
fixing such parts
P
No deterioration of the fixing properties of snap-in
devices used in parts that are likely to be removed
during installation or servicing
P
Tests as described
P
Handles, knobs etc. fixed in a reliable manner
N/A
Fixing in wrong position of handles, knobs etc.
indicating position of switches or similar components
not possible
N/A
Axial force 15 N applied to parts, the shape being so
that an axial pull is unlikely to be applied
N/A
Axial force 30 N applied to parts, the shape being so
that an axial pull is likely to be applied
N/A
22.13
Unlikely that handles, when gripped as in normal use,
make the operators hand touch parts having a
temperature rise exceeding the value specified for
handles which are held for short periods only
N/A
22.14
No ragged or sharp edges creating a hazard for the
user in normal use, or during user maintenance
P
No exposed pointed ends of self tapping screws etc.,
liable to be touched by the user in normal use or
during user maintenance
P
22.15
Storage hooks and the like for flexible cords smooth
and well rounded
N/A
22.16
Automatic cord reels cause no undue abrasion or
damage to the sheath of the flexible cord, no
breakage of conductors strands, no undue wear of
contacts
N/A
Cord reel tested with 6000 operations, as specified
N/A
Electric strength test of 16.3, voltage of 1000 V
applied
N/A
Spacers not removable from the outside by hand or
by means of a screwdriver or a spanner
N/A
22.12
22.17
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 31 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
22.18
Current-carrying parts and other metal parts resistant
to corrosion under normal conditions of use
22.19
Driving belts not used as electrical insulation
N/A
22.20
Direct contact between live parts and thermal
insulation effectively prevented, unless material used
is non-corrosive, non-hygroscopic and noncombustible
N/A
Compliance is checked by inspection and, if
necessary, by appropriate test
N/A
Wood, cotton, silk, ordinary paper and fibrous or
hygroscopic material not used as insulation, unless
impregnated
N/A
This requirement does not apply to magnesium
oxide and mineral ceramic fibres used for the
N/A
22.21
Result - Remark
Verdict
P
electrical insulation of heating elements.
(IEC 60335-1/A2)
22.22
Appliances not containing asbestos
P
22.23
Oils containing polychlorinated biphenyl (PCB) not
used
P
22.24
Bare heating elements adequately supported
N/A
In case of rupture, the heating conductor is unlikely to
come in contact with accessible metal parts
N/A
22.25
Sagging heating conductors cannot come into
contact with accessible metal parts
N/A
22.26
The insulation between parts operating at safety
extra-low voltage and other live parts complies with
the requirements for double or reinforced insulation
N/A
22.27
Parts connected by protective impedance separated
by double or reinforced insulation
N/A
22.28
Metal parts of Class II appliances conductively
connected to gas pipes or in contact with water:
separated from live parts by double or reinforced
insulation
N/A
22.29
Class II appliances permanently connected to fixed
wiring so constructed that the required degree of
access to live parts is maintained after installation
P
22.30
Parts serving as supplementary or reinforced
insulation fixed so that they cannot be removed
without being seriously damaged, or
P
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 32 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
22.31
22.32
Requirement + Test
Result - Remark
Verdict
so constructed that they cannot be replaced in an
incorrect position, and so that if they are omitted, the
appliance is rendered inoperable or manifestly
incomplete
P
Clearances and creepage distances over
supplementary and reinforced insulation not reduced
below values specified for supplementary insulation
P
Creepage distances and clearances over
supplementary or reinforced insulation not reduced to
less than 50% of values specified in 29 if wires,
screws etc. becomes loose
P
Supplementary and reinforced insulation designed or
protected against deposition of dirt or dust
P
Supplementary insulation of natural or synthetic
rubber resistant to ageing, or arranged and
dimensioned so that creepage distances are not
reduced below values specified in 29.2
N/A
Ceramic material not tightly sintered, similar material
or beads alone not used as supplementary or
reinforced insulation
N/A
Oxygen bomb test at 70 °C for 96 h and 16 h at room
temperature
N/A
Insulating material in which heating conductors are
embedded is considered to be basic insulation and
not reinforced insulation (IEC 60335-1/A2)
N/A
Conductive liquids that are or may become
accessible in normal use are not in direct contact with
live parts
N/A
Electrodes not used for heating liquids
N/A
For class II constructions, conductive liquids that are
or may become accessible in normal use, not in
direct contact with basic or reinforced insulation
N/A
For class II constructions, conductive liquids which
are in contact with live parts, not in direct contact with
reinforced insulation
N/A
22.34
Shafts of operating knobs, handles, levers etc. not
live, unless the shaft is not accessible when the part
is removed
N/A
22.35
Handles, levers and knobs, held or actuated in
normal use, not becoming live in the event of an
basic insulation fault (IEC 60335-1/A2)
N/A
22.33
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 33 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
Such parts being of metal, and their shafts or fixings
are likely to become live in the event of an basic
insulation fault, they are either adequately covered
by insulation material, or their accessible parts are
separated from their shafts or fixings by
supplementary insulation (IEC 603351/A2)
N/A
This requirement does not apply to handles, levers
and knobs on stationary appliances other than those
of electrical components, provided they are either
reliably connected to an earthing terminal or earthing
contact, or separated from live parts by earthed metal
N/A
22.36
Handles continuously held in the hand in normal use
are so constructed that when gripped as in normal
use, the operators hand is not likely to touch metal
parts, unless they are separated from live parts by
double or reinforced insulation
N/A
22.37
Capacitors in Class II appliances not connected to
accessible metal parts, unless complying with 22.42
N/A
Metal casings of capacitors in Class II appliances
separated from accessible metal parts by
supplementary insulation, unless complying with
22.42
N/A
22.38
Capacitors not connected between the contacts of a
thermal cut-out
N/A
22.39
Lamp holders used only for the connection of lamps
N/A
22.40
Motor-operated appliances and combined appliances
intended to be moved while in operation, or having
accessible moving parts, fitted with a switch to control
the motor. The actuating member of the switch being
easily visible and accessible
N/A
The appliance can operate continuously,
automatically or remotely without giving rise
N/A
to a hazard, appliances for remote operation shall
be fitted with a switch for stopping the operation of
the appliance. The actuating member of this switch
shall be easily visible and accessible
(IEC 60335-1/A2)
22.41
No components, other than lamps, containing
mercury
P
22.42
Protective impedance consisting of at least two
separate components
N/A
Values specified in 8.1.4 not exceeded if any one of
the components are short-circuited or open-circuited
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 34 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
22.43
Appliances adjustable for different voltages,
accidental changing of the setting of the voltage
unlikely to occur
N/A
22.44
Appliances shall not have an enclosure that is
shaped or decorated like a toy
(IEC 60335-1/A2)
P
22.45
When air is used as reinforced insulation, clearances
not reduced below the values specified in 29.1.4 due
to deformation as a result of an external force applied
to the enclosure
N/A
22.46
Software used in protective electronic circuits shall be
software class B or software class C (IEC 603351/A1)
N/A
22.47
Appliances intended to be connected to the water
mains shall withstand the water pressure expected in
normal use (IEC 60335-1/A1)
N/A
22.48
Appliances intended to be connected to the water
mains shall be constructed to prevent backsiphonage
of non-potable water into the water mains (IEC
60335-1/A1)
N/A
22.49
For remote operation, the duration of operation
shall be operated without giving rise to a hazard:
(IEC 60335-1/A2)
N/A
- set before the appliance is started
N/A
- the appliance switches off automatically at the end
of a cycle
N/A
- it can operate continuously
N/A
22.50
Controls incorporated in the appliance shall take
priority over controls actuated by remote operation
(IEC 60335-1/A2)
N/A
22.51
A control on the appliance shall be manually
adjusted to the setting for remote operation before
the appliance can be operated in this mode.
N/A
(IEC 60335-1/A2)
There shall be a visual indication on the appliance
showing that the appliance is adjusted for remote
operation, or (IEC 60335-1/A2)
N/A
The manual setting and the visual indication of the
remote mode are not necessary on appliances if it
can operate continuously or automatically or
remotely without giving rise to a hazard.
N/A
(IEC 60335-1/A2)
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 35 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
22.52
Socket-outlets on appliances accessible to the user
shall be in accordance with the socket-outlet
system used in the country in which the appliance is
sold. (IEC 60335-1/A2)
N/A
22.101
Appliances having provision for attaching a luminaire
incorporate appropriate terminals and internal wiring
(IEC 60335-2-80)
N/A
23
INTERNAL WIRING
23.1
Wireways smooth and free from sharp edges
P
Wires protected against contact with burrs, cooling
fins etc.
P
Wire holes in metal well rounded or provided with
bushings
N/A
Wiring effectively prevented from coming into contact
with moving parts
P
Beads etc. on live wires cannot change their position,
and are not resting on sharp edges or corners
N/A
Beads inside flexible metal conduits contained within
an insulating sleeve
N/A
Electrical connections and internal conductors
movable relatively to each other not exposed to
undue stress
N/A
Flexible metallic tubes not causing damage to
insulation of conductors
N/A
Open-coil springs not used
N/A
Adequate insulating lining provided inside a coiled
spring, the turns of which touch one another
N/A
No damage after 100 000 flexings for conductors
flexed during normal use and at rated voltage
(IEC 60335-2-80)
N/A
Electric strength test, 1000 V between live parts and
accessible metal parts
N/A
23.4
Bare internal wiring sufficiently rigid and fixed
N/A
23.5
The insulation of internal wiring withstanding the
electrical stress likely to occur in normal use
P
No breakdown when a voltage of 2000 V is applied
for 15 min between the conductor and metal foil
wrapped around the insulation
P
Sleeving used as supplementary insulation on
internal wiring retained in position by positive means
N/A
23.2
23.3
23.6
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 36 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
23.7
The colour combination green/yellow used only for
earthing conductors
Green/yellow is not used in the
appliance.
23.8
Aluminium wires not used for internal wiring
No aluminium wire.
P
23.9
No lead-tin soldering of stranded conductors where
they are subject to contact pressure, unless
No soldering for this reason.
P
N/A
clamping means so constructed that there is no risk
of bad contact due to cold flow of the solder
N/A
23.10
The insulation and sheath of internal wiring, in
external hoses for the connection of appliances to
the water mains, shall be at least equivalent to that
of light polyvinyl chloride sheathed flexible cords,
code designation 60227 IEC 52 (IEC 60335-1/A1)
N/A
24
COMPONENTS
P
24.1
Components comply with safety requirements in
relevant IEC standards
P
List of components
24.1.1
(see appended table)
P
Components not tested and found to comply with
relevant IEC standard for the number of cycles
specified are tested in accordance with 24.1.1 to
24.1.9 (IEC 60335-1/A2)
N/A
Components not tested and found to comply with
relevant IEC standard for the number of cycles
specified are tested in accordance with 24.1.1 to
24.1.6
N/A
Components not tested and found to comply with
relevant IEC standard, components not marked or
not used in accordance with its marking, tested under
the conditions occurring in the appliance
N/A
Lampholders and starterholders that have not been
previously tested and found to comply with the
relevant IEC standard are tested as a part of the
appliance and shall additionally comply with the
gauging and interchangeability requirements of the
relevant IEC standard under the conditions
occurring in the appliance. (IEC 60335-1/A2)
N/A
Capacitors likely to be permanently subjected to the
supply voltage and used for radio interference
suppression or for voltage dividing, complying with
IEC 60384-14, or
tested according to annex F
TRF No. IEC60335_2_80C
Approved component
P
N/A
TRF originator: KEMA
Page 37 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
24.1.2
Safety isolating transformers complying with IEC
61558-2-6, or
N/A
tested according to annex G
N/A
24.1.3
24.1.4
Result - Remark
Verdict
Switches complying with IEC 61058-1, the number of
cycles of operation being at least 10 000, or
P
tested according to annex H
N/A
Automatic controls complying with IEC 60730-1 with relevant part 2. The number of
cycles of operation being:
N/A
- thermostats:
10 000
N/A
1 000
N/A
300
N/A
- temperature limiters:
- self-resetting thermal cut-outs:
- non-self-resetting thermal cut-outs:
30 Approved component
3 000
P
10 000
N/A
1 000
N/A
- timers:
- energy regulators:
- voltage maintain non-self-resetting
thermal cut-outs (IEC 60335-1/A1)
- other non-self-resetting thermal cut-outs
(IEC 60335-1/A1)
P
30
N/A
Appliance couplers complying with IEC 60320-1
N/A
However, appliances classified higher than IPX0, the
appliance couplers complying with IEC 60320-2-3
N/A
24.1.6
Small lamp holders similar to E10 lampholders
complying with IEC 60238, the requirements for E10
lampholders being applicable
N/A
24.1.7
If the remote operation of the appliance is via a
telecommunication network, the telecommunication
interface circuitry in the appliance shall comply with
IEC 62151. (IEC 60335-1/A2)
N/A
24.1.8
Thermal links shall comply with IEC 60691, or
24.1.5
P
(IEC 60335-1/A2)
Thermal links are considered to be an intentionally
weak part for the purposes of Clause 19.
N/A
(IEC 60335-1/A2)
24.1.9
Relays, other than motor starting relays, are tested
as part of the appliance. (IEC 60335-1/A2)
TRF No. IEC60335_2_80C
N/A
TRF originator: KEMA
Page 38 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
N/A
24.2
However, they are also tested in accordance with
Clause 17 of IEC 60730-1 under the maximum load
conditions occurring in the appliance for at least the
number of operations in 24.1.4 selected according
to the relay function in the appliance.
(IEC 60335-1/A2)
Switches or automatic controls in flexible cords are
allowed for appliances not exceeding 25 W
(IEC 60335-2-80)
No devices causing the protective device in the fixed
wiring to operate in the event of a fault in the
appliance
No thermal cut-outs that can be reset by soldering
Switches intended for all-pole disconnection of
stationary appliances are directly connected to the
supply terminals and having a contact separation in
all poles, providing full disconnection under
overvoltage category III conditions
Plugs and socket-outlets for extra-low voltage circuits
and heating elements, not interchangeable with plugs
and socket-outlets listed in IEC 60083 or IEC 609061 or with connectors and appliance inlets complying
with the standard sheets of IEC 60320-1
N/A
Capacitors in auxiliary windings of motors marked
with their rated voltage and capacitance and used
accordingly
N/A
Capacitors in appliances for which 30.2.3 is
applicable and that are permanently connected in
series with a motor winding, are of class P1 or P2 of
IEC 60252
N/A
Voltage across capacitors in series with a motor
winding does not exceed 1,1 times rated voltage,
when the appliance is supplied at 1,1 times rated
voltage under minimum load
N/A
Working voltage of motors connected to the supply
mains and having basic insulation that is inadequate
for the rated voltage of the appliance, not exceeding
42V.
N/A
In addition, the motors are complying with the
requirements of Annex I
N/A
24.7
Hose-sets for the connection of appliances to the
water mains shall comply with IEC 61770 and
supplied with the appliances (IEC 60335-1/A1)
N/A
24.101
Thermal cut-outs in duct fans in order to comply with
cl. 19 are not self-resetting (IEC 60335-2-80)
N/A
24.3
24.4
24.5
24.6
TRF No. IEC60335_2_80C
Result - Remark
Verdict
N/A
N/A
N/A
N/A
TRF originator: KEMA
Page 39 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
25
SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS
25.1
Appliance not intended for permanent connection to fixed wiring, means for connection
to the supply:
N/A
- supply cord fitted with a plug
N/A
- an appliance inlet having at least the same degree
of protection against moisture as required for the
appliance
N/A
P
- pins for insertion into socket-outlets
25.2
Appliance not provided with more than one means of
connection to the supply mains
Stationary appliance for multiple supply may be
provided with more than one means of connection,
provided electric strength test of 1250 V for 1 min
between each means of connection causes no
breakdown
25.3
25.4
25.5
P
N/A
Connection of supply conductors for appliance
intended to be permanently connected to fixed wiring
possible after the appliance has been fixed to its
support
P
Appliance provided with a set of terminals for the
connection of cables or fixed wiring, cross-sectional
areas specified in 26.6
N/A
Appliance provided with a set of terminals allowing
the connection of a flexible cord
P
Appliance provided with a set of supply leads
accommodated in a suitable compartment
N/A
Appliance provided with a set of terminals and cable
entries, conduit entries, knock-outs or glands,
allowing connection of appropriate type of cable or
conduit
N/A
Cable and conduit entries, rated current of appliance
not exceeding 16 A, dimensions according to
table 10
P
Introduction of conduit or cable does not reduce
clearances or creepage distances below values
specified in 29
P
Method for assemble supply cord with the appliance:
P
- type X attachment
N/A
- type Y attachment
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 40 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
- type Z attachment is allowed for portable fans
(IEC 60335-2-80)
N/A
Type X attachment, other than those with a specially
prepared cord, not used for flat twin tinsel cords
N/A
25.6
Plugs fitted with only one flexible cord
N/A
25.7
Supply cord shall be one of the following types:
(IEC 60335-1/A2)
N/A
- at least ordinary tough rubber sheathed cord
(60245 IEC 53)
(IEC 60335-1/A2)
N/A
- at least ordinary polychloroprene sheathed flexible
cord [60245 IEC 57] (IEC 60335-1/A2)
N/A
- at least cross-linked polyvinyl chloride sheathed
cords [60245 IEC 87] (IEC 60335-1/A2)
N/A
- Polyvinyl chloride sheathed, not be used to touch
metal parts having a temperature rise exceeding 75
K during the test of Clause 11. Their properties
shall be at least those of: (IEC 60335-1/A2)
N/A
--light polyvinyl chloride sheathed cord (code
designation 60227 IEC 52), for appliances
having a mass not exceeding 3 kg or
N/A
--ordinary polyvinyl chloride sheathed cord (code
designation 60227 IEC 53), for other appliances
N/A
-Heat resistant polyvinyl chloride sheathed, not be
for type X attachment other than specially prepared
cords. Their properties shall be at least those of:
(IEC 60335-1/A2)
N/A
--heat-resistant light polyvinyl chloride sheathed
cord (code designation 60227 IEC 56), for
appliances having a mass not exceeding 3 kg or
N/A
Nominal cross-sectional area of supply cords
according to table 11; rated current (A); crosssectional area (mm²) .............................................:
25.9
Supply cord not in contact with sharp points or
edges
N/A
25.10
Green/yellow core for earthing purposes in Class I
appliance
N/A
25.11
Conductors of supply cords not consolidated by
lead-tin soldering where they are subject to contact
pressure, unless
N/A
clamping means so constructed that there is no risk
of bad contacts due to cold flow of the solder
N/A
TRF No. IEC60335_2_80C
-
N/A
25.8
TRF originator: KEMA
Page 41 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
25.12
Moulding the cord to part of the enclosure does not
damage the insulation of the supply cord
N/A
25.13
Inlet opening so shaped as to prevent damage to
the supply cord
N/A
Unless the enclosure at the inlet opening is of
insulation material, a non-detachable lining or
bushing complying with 29.3 for supplementary
insulation provided
N/A
If unsheathed supply cord, a similar additional
bushing or lining is required, unless
N/A
the appliance is class 0
N/A
Supply cords adequately protected against excessive
flexing
N/A
Flexing test:
N/A
25.14
25.15
Result - Remark
Verdict
- applied force (N).....................................................:
-
N/A
- number of flexings.................................................. :
-
N/A
The test does not result in:
N/A
- short circuit between the conductors
N/A
- breakage of more than 10% of the strands of any
conductor
N/A
- separation of the conductor from its terminal
N/A
- loosening of any cord guard
N/A
- damage, within the meaning of the standard, to the
cord or the cord guard
N/A
- broken strands piercing the insulation and
becoming accessible
N/A
Conductors of the supply cord relieved from strain,
twisting and abrasion by use of cord anchorage
P
The cord cannot be pushed into the appliance to
such an extent that the cord or internal parts of the
appliance can be damaged
P
Pull and torque test of supply cord, values shown in
table 10: pull (N); torque (not on automatic cord reel)
(Nm)..........................................................................:
30 N; 0,1 Nm
P
Max. 2 mm displacement of the cord, and conductors
not moved more than 1 mm in the terminals
P
Creepage distances and clearances not reduced
below values specified in 29.1
P
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 42 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
25.16
Cord anchorages for type X attachments constructed and located so that:
N/A
- replacement of the cord is easily possible
N/A
- it is clear how the relief from strain and the
prevention of twisting are obtained
N/A
- they are suitable for different types of cord
N/A
- cord cannot touch the clamping screws of cord
anchorage if these screws are accessible, unless
separated from accessible metal parts by
supplementary insulation
N/A
- the cord is not clamped by a metal screw which
bears directly on the cord
N/A
- at least one part of the cord anchorage securely
fixed to the appliance, unless part of a specially
prepared cord
N/A
- screws which have to be operated when replacing
the cord do not fix any other component, if applicable
N/A
- if labyrinths can be bypassed the test of 25.15 is
nevertheless withstood
N/A
- for Class 0, 0I and I appliances: they are of
insulating material or are provided with an insulating
lining, unless a failure of the insulation of the cord
does not make accessible metal parts live
N/A
- for Class II appliances: they are of insulating
material, or if of metal, they are insulated from
accessible metal parts by supplementary insulation
N/A
25.17
Adequate cord anchorages for type Y and Z
attachment
N/A
25.18
Cord anchorages only accessible with the aid of a
tool, or
P
so constructed that the cord can only be fitted with
the aid of a tool
N/A
Type X attachment, glands not used as cord
anchorage in portable appliances
N/A
Tying the cord into a knot or tying the cord with string
not used
N/A
Conductors of the supply cord for type Y and Z
attachment adequately additionally insulated
N/A
25.19
25.20
TRF No. IEC60335_2_80C
Result - Remark
Verdict
TRF originator: KEMA
Page 43 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
25.21
Space for supply cord for type X attachment or for
connection of fixed wiring constructed to permit
checking of conductors with respect to correct
positioning and connection before fitting any cover,
no risk of damage to the conductors when fitting the
cover, no contact with accessible metal parts if a
conductor becomes loose, etc.
P
For portable appliances, the uninsulated end of a
conductor prevented from any contact with
accessible metal parts, unless the end of the cord is
such that the conductors are unlikely to slip free
N/A
Appliance inlet:
N/A
- live parts not accessible during insertion or removal
N/A
- connector can be inserted without difficulty
N/A
- the appliance is not supported by the connector
N/A
- is not for cold conditions if temp. rise of external
metal parts exceeds 75 K, unless the supply cord is
not likely to touch such metal parts
N/A
Interconnection cords comply with the requirements
for the supply cord, except as specified
N/A
If necessary, electric strength test of 16.3
N/A
25.24
Interconnection cords not detachable without the aid
of a tool if compliance with the standard is impaired
when they are disconnected
N/A
25.25
Dimensions of pins compatible with the dimensions
of the relevant socket-outlet. Dimensions of pins and
engagement face in accordance with the relevant
plug in IEC 60083
N/A
26
TERMINALS FOR EXTERNAL CONDUCTORS
P
26.1
Appliances provided with terminals or equally
effective devices for connection of external
conductors
P
Terminals only accessible after removal of a nondetachable cover
P
25.22
25.23
Only the earthing terminal may be accessible if a tool
is required to make the connections and means to
provide to clamp the wire independently from its
connection (IEC 60335-1/A1)
TRF No. IEC60335_2_80C
Result - Remark
Verdict
N/A
TRF originator: KEMA
Page 44 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
26.2
Appliances with type X attachment and appliances
for connection to fixed wiring provided with terminals
in which connections are made by means of screws,
nuts or similar devices, unless the connections are
soldered
By screw
Verdict
P
Screws and nuts serve only to clamp supply
conductors, except
P
internal conductors, if so arranged that they are
unlikely to be displaced when fitting the supply
conductors
N/A
If soldered connections used, the conductor so
positioned or fixed that reliance is not placed on
soldering alone
N/A
Soldering alone used, barriers provided, clearances
and creepage distances satisfactory if the conductor
becomes free at the soldered joint
N/A
Terminals for type X attachment and for connection
to fixed wiring so constructed that the conductor is
clamped between metal surfaces with sufficient
contact pressure and without damaging the
conductor
P
Terminals for type X attachment and those for connection to fixed wiring so fixed that
when tightening or loosening the clamping means:
P
- the terminal does not loosen
P
- internal wiring is not subjected to stress
P
- clearances and creepage distances are not reduced
below the values in 29
P
Compliance checked by inspection and by the test of 0,28
subclause 9.6 of IEC 60999-1, the torque applied
being equal to two-thirds of the torque specified.
Nominal diameter of thread (mm); screw category;
torque (Nm) (IEC 60335-1/A2)..............................:
P
26.4
Terminals for type X attachment, except those with a
specially prepared cord, and those for connection to
fixed wiring, no special preparation of conductors
required, and so constructed or placed that
conductors prevented from slipping out
P
26.5
Terminals for type X attachment so located or
shielded that if a wire of a stranded conductor
escapes, no risk of accidental connection to other
parts that result in a hazard
N/A
Stranded conductor test, 8 mm insulation removed
N/A
26.3
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 45 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
N/A
No contact between live parts and accessible metal
parts and, for class II constructions, between live
parts and metal parts separated from accessible
metal parts by supplementary insulation only
26.6
Terminals for type X attachment and for connection
to fixed wiring suitable for connection of conductors
with required cross-sectional area according to
table 13; rated current (A); nominal cross-sectional
area (mm²)................................................................:
Terminal block is suitable for
2
connection up to 2,5mm
rated current < 3A
P
Terminals only suitable for a specially prepared cord
N/A
26.7
Terminals for type X attachment accessible after
removal of a cover or part of the enclosure
N/A
26.8
Terminals for the connection to fixed wiring, including
the earthing terminal, located close to each other
P
26.9
Terminals of the pillar type constructed and located
as specified
P
26.10
Terminals with screw clamping and screwless
terminals not used for flat twin tinsel cords, unless
conductors ends fitted with a device suitable for
screw terminals
N/A
Pull test of 5 N to the connection
N/A
For type Y and Z attachment: soldered, welded,
crimped and similar connections may be used
N/A
For Class II appliances: the conductor so positioned
or fixed that reliance is not placed on soldering,
welding or crimping alone
N/A
For Class II appliances: soldering, welding or
crimping alone used, barriers provided, clearances
and creepage distances satisfactory if the conductor
becomes free
N/A
26.11
27
27.1
PROVISION FOR EARTHING
P
Accessible metal parts of Class 0I and I appliances,
permanently and reliably connected to an earthing
terminal or contact of the appliance inlet
N/A
Earthing terminals not connected to neutral terminal
N/A
Class 0, II and III appliances have no provision for
earthing
Safety extra-low voltage circuits not earthed, unless
protective extra-low voltage circuits
TRF No. IEC60335_2_80C
P
N/A
TRF originator: KEMA
Page 46 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
27.2
Clamping means adequately secured against
accidental loosening
N/A
Terminals used for the connection of external
equipotential bonding conductors allow connection of
conductors of 2.5 to 6 mm², and
N/A
do not provide earthing continuity between different
parts of the appliance
N/A
Conductors cannot be loosened without the aid of a
tool
N/A
For appliances with supply cord, current-carrying
conductors become taut before earthing conductor, if
the cord slips out of the cord anchorage
N/A
If a detachable part having an earth connection is
plugged into another part of the appliance, the earth
connection shall be made before the currentcarrying connections are established and the
current carrying connections shall be separated
before the earth connection when removing the part
(IEC 60335-1/A1)
N/A
No risk of corrosion resulting from contact between
metal of earthing terminal and other metal
N/A
Adequate resistance to corrosion of coated or
uncoated parts providing earthing continuity, other
than parts of a metal frame or enclosure
N/A
Parts of steel providing earthing continuity provided at
the essential areas with an electroplated coating,
thickness at least 5 µm
N/A
Adequate protection against rusting of parts of
coated or uncoated steel, only intended to provide or
transmit contact pressure
N/A
In case of aluminium alloys precautions taken to
avoid risk of corrosion
N/A
Low resistance of connection between earthing
terminal and earthed metal parts
N/A
This requirement does not apply to connections
providing earthing continuity in the protective extralow voltage circuit, provided that clearances of basic
insulation are based on the rated voltage of the
appliance
N/A
Resistance not exceeding 0,1 1 at the specified lowresistance test
N/A
27.3
27.4
27.5
TRF No. IEC60335_2_80C
Result - Remark
Verdict
TRF originator: KEMA
Page 47 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
27.6
The printed conductors of printed circuit boards not
used to provide earthing continuity in hand held
appliances (IEC 60335-1/A2)
N/A
They may be used in other appliances if at least two
tracks are used with independent soldering points
and the appliance complies with 27.5 for each circuit
(IEC 60335-1/A2)
N/A
28
SCREWS AND CONNECTIONS
P
28.1
Fixings, electrical connections and connections
providing earthing continuity withstand mechanical
stresses
P
Screws not of soft metal liable to creep, such as zinc
or aluminium
28.3
P
Diameter of screws of insulating material min. 3 mm
N/A
Screws of insulating material not used for any
electrical connection or connections providing
earthing continuity
N/A
Screws used for electrical connections or
connections providing earthing continuity screw into
metal
P
Screws not of insulating material if their replacement
by a metal screw can impair supplementary or
reinforced insulation
N/A
Type X attachment, screws to be removed for
replacement of supply cord or for user maintenance,
not of insulating material if their replacement by a
metal screw can impair basic insulation
N/A
For screws and nuts; test as specified
28.2
Only metal screws used
Electrical connections and connections providing
earthing continuity constructed so that contact
pressure not transmitted through insulating material
liable to shrink or distort, unless shrinkage or
distortion compensated
(see appended table)
Class II appliance
P
N/A
This requirement does not apply to electrical
connections in circuits carrying a current not
exceeding 0.5A
N/A
Space-threaded (sheet metal) screws only used for
electrical connections if they clamp the parts together
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 48 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
N/A
Thread-cutting (self-tapping) screws and thread
rolling screws shall only be used for electrical
connections if they generate a full form standard
machine screw thread. (IEC 60335-1/A2)
N/A
However, such screws not used if they are likely to
be operated by the user or installer
(IEC 60335-1/A2)
N/A
Thread-cutting, thread rolling and space-threaded
screws may be used in connections providing
earthing continuity provided it is not necessary to
disturb the connection of normal use, user
maintenance, when replacing a supply cord having a
type X attachment and during installation.
(IEC 60335-1/A2)
At least two screws must be used for each
connection providing earthing continuity unless:
(IEC 60335-1/A2)
N/A
The screw forms a thread having a length of at least
half the diameter of the screw.
N/A
(IEC 60335-1/A2)
28.4
29
Screws and nuts that make mechanical connection
Mechanical connection does
secured against loosening if they also make electrical not serve electrical connection.
connections or connections providing earthing
continuity
N/A
Rivets for electrical connections or connections
providing earthing continuity secured against
loosening if subjected to torsion
N/A
CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION
P
Clearances, creepage distances and solid insulation
withstand electrical stress
P
For coatings used on printed circuit boards to protect No coating used
the microenvironment (Type 1 coating) or to provide
basic insulation (Type 2 coating), Annex J applies.
(IEC 60335-1/A2)
N/A
The microenvironment is pollution degree 1 under
Type 1 coating. (IEC 60335-1/A2)
N/A
There are no clearance or creepage distance
requirements under Type 2 coating.
(IEC 60335-1/A2)
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 49 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
29.1
Clearances not less than the values specified in table
16, taking into account the rated impulse voltage for
the overvoltage categories of table 15
The values specified may be smaller for basic
insulation and functional insulation if the clearance
meets the impulse voltage test of clause 14
Appliances are in overvoltage category II
29.1.1
Result - Remark
Verdict
P
N/A
P
Clearances less than specified in table 16 not
allowed for basic insulation of class 0 and class 0I
appliances,
N/A
or if pollution degree 3 is applicable
N/A
Compliance is checked by inspection and
measurements as specified
P
Clearances of basic insulation withstand the
overvoltages, taking into account the rated impulse
voltage and the impulse voltage test of Clause 14
(IEC 60335-1/A2)
P
Clearance at the terminals of tubular sheathed
heating elements may be reduced to 1mm if the
microenvironment is pollution degree 1
N/A
Lacquered conductors of windings assumed to be
bare conductors, but the clearances specified in table
16 are reduced by 0.5mm for rated impulse voltages
of at least 1500V
N/A
29.1.2
Clearances of supplementary insulation not less than
those specified for basic insulation in table 16
P
29.1.3
Clearances of reinforced insulation not less than
those specified for basic insulation in table 16, but
using the next higher step for rated impulse voltage
P
29.1.4
For functional insulation, the values of table 16 are
applicable, unless
P
the appliance complies with clause 19 with the
functional insulation short-circuited
N/A
Clearances at crossover points of lacquered
conductors not measured
N/A
Clearance between surfaces of PTC heating
elements may be reduced to 1mm
N/A
Lacquered conductors of windings assumed to be
bare conductors, but the clearances specified in table
16 are reduced by 0.5mm for rated impulse voltages
of at least 1500V
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 50 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
29.1.5
Appliances having higher working voltage than rated
voltage, the voltage used for determining clearances
from table 16 is the sum of the rated impulse voltage
and the difference between the peak value of the
working voltage and the peak value of the rated
voltage
N/A
If the secondary winding of a step-down transformer
is earthed, or if there is an earthed screen between
the primary and secondary windings, clearances of
basic insulation on the secondary side not less than
those specified in table 16, but using the next lower
step for rated impulse voltage
N/A
Circuits supplied with a voltage lower than rated
voltage, clearances of functional insulation based on
the working voltage used as the rated voltage in table
15
N/A
29.2
29.2.1
Creepage distances not less than those appropriate
for the working voltage, taking into account the
material group and the pollution degree
Result - Remark
Verdict
P
Pollution degree 2 applies, unless
N/A
precautions taken to protect the insulation; pollution
degree 1
N/A
insulation subjected to conductive pollution; pollution
degree 3
P
Compliance is checked by inspection and
measurements as specified
P
Microenvironment is pollution degree 3 unless
insulation is enclosed or located that it is unlikely to
be exposed to pollution during normal use (IEC
60335-2-80)
P
Creepage distances of basic insulation not less than
specified in table 17
P
For pollution degree 1, creepage distance not less
than the minimum specified for the clearance in table
16, if the clearance has been checked according to
the test of clause 14
N/A
29.2.2
Creepage distances of supplementary insulation at
least as specified for basic insulation in table 17
P
29.2.3
Creepage distances of reinforced insulation at least
double as specified for basic insulation in table 17
P
29.2.4
Creepage distances of functional insulation not less
than specified in table 18
P
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 51 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
29.3
Requirement + Test
Result - Remark
Verdict
Creepage distances may be reduced if the appliance
complies with clause 19 with the functional insulation
short-circuited
N/A
Solid insulation having a minimum thickness of 1mm
for supplementary insulation,
P
and 2mm for reinforced insulation
P
This requirement does not apply if the supplementary
insulation, other than mica or similar scaly material,
consists of at least two layers, each of the layers
withstands the electric strength test of 16.3
N/A
This requirement does not apply if the reinforced
insulation, other than mica or similar scaly material,
consists of at least three layers, any two layers
together withstand the electric strength test of 16.3
N/A
This requirement also does not apply to inaccessible
insulation and does not exceed the maximum
permissible temperature values, or
N/A
if the insulation, after conditioning as specified,
withstands the electric strength test of 16.3
N/A
29.3.1
The thickness of the insulation shall be at least
- 1 mm for supplementary insulation
- 2 mm for reinforced insulation
(IEC 60335-1/A1)
29.3.2
Each layer of material shall withstand the tests of
clause 16.3. Supplementary insulation shall consist
of at least 2 layer and reinforced insulation at least
3 layers (IEC 60335-1/A1)
N/A
29.3.3
The insulation is subjected to the dry heat test Bb of
IEC 60068-2-2 for 48 hours at a temperature of 50 K
in excess of the maximum temperature rise during
clause 19 and withstand the tests of clause 16.3
(IEC 60335-1/A1)
N/A
30
RESISTANCE TO HEAT AND FIRE
P
30.1
External parts of non-metallic material,
P
parts supporting live parts, and
P
Approved components
P
thermoplastic material providing supplementary or
reinforced insulation,
P
sufficiently resistant to heat
P
Ball-pressure test according to IEC 60695-10-2
P
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 52 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
External parts: at 40 °C plus the maximum
Enclosure tested on 75 °C
temperature rise determined during the test of clause
11, or at 75 °C, whichever is the higher; temperature
(°C)............................................................................:
Parts supporting live parts: at 40°C plus the
maximum temperature rise determined during the
test of clause 11, or at 125°C, whichever is the
higher; temperature (°C)...........................................:
30.2
-
P
N/A
Parts of thermoplastic material providing
supplementary or reinforced insulation, 25°C plus the
maximum temperature rise determined during clause
19, if higher; temperature (°C)..................................:
P
Relevant parts of non-metallic material adequately
resistant to ignition and spread of fire
P
(IEC 60335-1/A2)
This requirement does not apply to decorative trims,
knobs and other parts unlikely to be ignited or to
propagate flames that originate inside the appliance
(IEC 60335-1/A2)
N/A
Compliance checked by the test of 30.2.1.
In addition:
P
- attended appliances, 30.2.2 applies
N/A
- unattended appliances, 30.2.3 applies
P
Appliances for remote operation are considered to be
unattended and consequently so they need comply
with the test of 30.2.3. (IEC 60335-1/A2)
30.2.1
30.2.3
30.2.3.1
N/A
Glow-wire test of IEC 60695-2-11 at 550 °C, unless
P
the material is classified at least HB40 according to
IEC 60695-11-10
N/A
Parts for which the glow-wire test cannot be carried
out meet the requirements in ISO9772 for material
classified HBF (IEC 60335-1/A2)
N/A
Appliances operated while unattended, tested as
specified in 30.2.3.1 and 30.2.3.2
P
Test not applicable to conditions as specified
P
Parts of non-metallic material supporting
connections carrying a current exceeding 0.2A
during normal operation, and (IEC 60335-1/A2)
parts of non-metallic material within a distance of
3mm, and (IEC 60335-1/A2)
TRF No. IEC60335_2_80C
Current is less than 0,2 A
N/A
N/A
TRF originator: KEMA
Page 53 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
30.2.3.2
Requirement + Test
Result - Remark
Verdict
Parts within 3mm but it is shielded from the
connection by a different material, then the
interposed shielding material in place but not directly
to the shielded material (IEC 60335-1/A2)
N/A
having a glow-wire flammability index of at least
850°C according to IEC 60695-2-11.
(IEC 60335-1/A2)
N/A
However, the test is not carried out on such parts:
(IEC 60335-1/A2)
N/A
- the material classified as having a glow-wire
flammability index of at least 850 °C according to
IEC 60695-2-12 and the thickness comply with the
requirements, or
N/A
- small parts, comply with the needle-flame test of
Annex E or
N/A
- small parts, classified as V-0 or V-1 according to
IEC 60695-11-10 and no thicker than the relevant.
N/A
Parts of insulating material supporting currentcarrying connections, and
P
parts of insulating material within a distance of 3mm,
subjected to glow-wire test of IEC 60695-2-11
N/A
Approved components
N/A
Test not carried out on material having a glow-wire
ignition temperature according to IEC 60695-2-13 as
specified
N/A
Where an non-metallic material is within 3 mm of a
current carrying connection, but is shielded from the
connection by a different material, then the
interposed shielding material in place but not
directly to the shielded material shall comply with
IEC 60695-2-11 (IEC 60335-1/A2)
N/A
Glow-wire test of IEC 60695-2-11, the temperature being:
P
-750°C, for connections carrying a current exceeding
0,2A during normal operation
-650°C, for other connections
N/A
Approved components
N/A
Parts that during the test produce a flame persisting
longer than 2 s, tested as specified
N/A
If a flame persists longer than 2 s during the test,
parts above the connection, as specified, subjected
to the needle-flame test of annex E, unless
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 54 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
the material is classified as V-0 or V-1 according to
IEC 60695-11-10, no thicker than the relevant part
of the appliance.
(IEC 60335-1/A2)
30.2.4
Base material of printed circuit boards subjected to
needle-flame test of annex E
Test not applicable to conditions as specified
(IEC 60335-1/A2)
31
32
A
B
3.1.9
Verdict
N/A
P
N/A
RESISTANCE TO RUSTING
P
Relevant ferrous parts adequately protected against
rusting
P
RADIATION, TOXICITY AND SIMILAR HAZARDS
N/A
Appliance does not emit harmful radiation
N/A
Appliance does not present a toxic or similar hazard
due to their operation in normal use.
(IEC 60335-1/A2)
N/A
Compliance is checked by the limits or tests
specified in Part 2. (IEC 60335-1/A2)
N/A
However, if no limits or tests are specified in Part 2,
then the appliance is deemed to comply with the
requirement without testing.
(IEC 60335-1/A2)
N/A
ANNEX A (INFORMATIVE)
ROUTINE TESTS
N/A
Description of routine tests to be carried out by the
manufacturer
N/A
ANNEX B (NORMATIVE)
APPLIANCES POWERED BY RECHARGEABLE BATTERIES
N/A
The following modifications to this standard are
applicable for appliances powered by batteries that
are recharged in the appliance
N/A
This annex does not apply to battery chargers
N/A
Appliance operated under the following conditions:
N/A
-the appliance, supplied by its fully charged battery,
operated as specified in relevant part 2
N/A
-the battery is charged, the battery being initially
discharged to such an extent that the appliance
cannot operate
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 55 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
-if possible, the appliance is supplied from the supply
mains through its battery charger, the battery being
initially discharged to such an extent that the
appliance cannot operate. The appliance is operated
as specified in relevant part 2
N/A
If the appliance incorporates inductive coupling
between two parts that are detachable from each
other, the appliance is supplied from the supply
mains with the detachable part removed
N/A
3.6.2
Part to be removed in order to discard the battery is
not considered to be detachable
N/A
5.101
Appliances supplied from the supply mains tested as
specified for motor-operated appliances
N/A
7.1
Battery compartment for batteries intended to be
replaced by the user, marked with battery voltage
and polarity of the terminals
N/A
7.12
The instructions for appliances incorporating
batteries intended to be replaced by the user includes
required information
N/A
Details about how to remove batteries containing
materials hazardous to the environment given
N/A
7.15
Markings placed on the part of the appliance
connected to the supply mains
N/A
8.2
Appliances having batteries that according to the
instruction may be replaced by the user need only
have basic insulation between live parts and the inner
surface of the battery compartment
N/A
If the appliance can be operated without batteries,
double or reinforced insulation required
N/A
11.7
The battery is charged for the period described
N/A
19.1
Appliances subjected to tests of 19.101, 19.102 and
19.103
N/A
19.101
Appliances supplied at rated voltage for 168 h, the
battery being continually charged
N/A
19.102
Short-circuiting of the terminals of the battery, being
fully charged, for appliances having batteries that can
be removed without the aid of a tool
N/A
19.103
Appliances having batteries replaceable by the user
supplied at rated voltage under normal operation with
the battery removed or in any position allowed by the
construction
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 56 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
21.101
Appliances having pins for insertion into socketoutlets have adequate mechanical strength, checked
according to procedure 2 of IEC 68-2-32
N/A
Part of the appliance incorporating the pins subjected to the free fall test, procedure 2,
of IEC 60068-2-32, the number of falls being:
N/A
- 100, the mass of part does not exceed 250 g
N/A
- 50, the mass of part exceeds 250 g
N/A
After the test, the requirements of 8.1, 15.1.1, 16.3
and clause 29 are met
N/A
22.3
Appliances having pins for insertion into socketoutlets tested as fully assembled as possible
N/A
25.13
An additional lining or bushing not required for
interconnection cords operating at safety extra-low
voltage
N/A
30.2
For parts of the appliance connected to the supply
mains during the charging period, 30.2.3 applies
N/A
For other parts, 30.2.2 applies
N/A
ANNEX C (NORMATIVE)
AGEING TEST ON MOTORS
N/A
Tests, as described, carried out when doubt with
regard to the temperature classification of the
insulation of a motor winding
N/A
ANNEX D (NORMATIVE)
ALTERNATIVE REQUIREMENTS FOR PROTECTED MOTORS
N/A
Applicable to motors that incorporate thermal motor
protectors (IEC 60335-1/A1)
N/A
Applicable to protected motors for unattended use,
test of 19.7 carried out on a separate sample
according to the specification
N/A
C
D
E
7
9
Result - Remark
Verdict
ANNEX E (NORMATIVE)
NEEDLE-FLAME TEST (IEC 60335-1, A2: 2006)
P
Needle-flame test carried out in accordance with
IEC 60695-11-5, with the following modifications:
P
Severities
P
The duration of application of the test flame is
30 s ± 1 s
P
Test procedure
P
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 57 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
9.1
The specimen so arranged that the flame can be
applied to a vertical or horizontal edge as shown in
the examples of figure 1
P
9.2
Application of needle-flame, modification:
P
The first paragraph does not apply
9.3
If possible, the flame is applied at least 10 mm from
a corner
P
The test is carried out on one specimen
P
If the specimen does not withstand the test, the test
may be repeated on two additional specimens, both
withstanding the test
11
Evaluation of test results
The duration of burning not exceeding 30 s
However, for printed circuit boards, the duration of
burning not exceeding 15 s
F
N/A
P
N/A
P
ANNEX F (NORMATIVE)
CAPACITORS
N/A
Capacitors likely to be permanently subjected to the
supply voltage, and used for radio interference
suppression or voltage dividing, comply with the
following clauses of IEC 60384-14, with the following
modifications:
N/A
1.5
Terminology
N/A
1.5.3
Class X capacitors tested according to subclass X2
N/A
1.5.4
This subclause is applicable
N/A
1.6
Marking
N/A
Items a) and b) are applicable
N/A
3.4
Approval testing
N/A
3.4.3.2
Table II is applicable as described
N/A
4.1
Visual examination and check of dimensions
N/A
This subclause is applicable
N/A
4.2
Electrical tests
N/A
4.2.1
This subclause is applicable
N/A
4.2.5
This subclause is applicable
N/A
4.2.5.2
Only table IX is applicable
N/A
Values for test A apply
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 58 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
However, for capacitors in heating appliances the
values for test B or C apply
N/A
Damp heat, steady state
N/A
This subclause is applicable
N/A
Only insulation resistance and voltage proof are
checked
N/A
Impulse voltage
N/A
This subclause is applicable
N/A
Endurance
N/A
Subclauses 4.14.1, 4.14.3, 4.14.4 and 4.14.7
applicable
N/A
Only insulation resistance and voltage proof are
checked
N/A
Visual examination, no visible damage
N/A
Passive flammability test
N/A
This subclause is applicable
N/A
Active flammability test
N/A
This subclause is applicable
N/A
ANNEX G (NORMATIVE)
SAFETY ISOLATING TRANSFORMERS
N/A
The following modifications to this standard are
applicable for safety isolating transformers:
N/A
7
Marking and instructions
N/A
7.1
Transformers for specific use marked with:
N/A
-name, trademark or identification mark of the
manufacturer or responsible vendor
N/A
-model or type reference
N/A
Overload protection of transformers and associated circuits
N/A
Fail-safe transformers comply with subclause 15.5 of
IEC 61558-1
N/A
Construction
N/A
Subclauses 19.1 and 19.1.2 of IEC 61558-2-6 are
applicable
N/A
Clearances, creepage distances and solid insulation
N/A
4.12
4.13
4.14
4.14.7
4.17
4.18
G
17
22
29
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 59 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
29.1 and
29.2
The distances specified in items 2a, 2c and 3 in table
13 of IEC 61558-1 apply
N/A
H
ANNEX H (NORMATIVE)
SWITCHES
N/A
Switches comply with the following clauses of IEC 61058-1, as modified:
N/A
-The tests of IEC 61058-1 carried out under the
conditions occurring in the appliance
N/A
-Before being tested, switches are operated 20 times
without load
N/A
Marking and documentation
N/A
Switches are not required to be marked
N/A
However, switches that can be tested separately
from the appliance marked with the manufacturer’s
name or trade mark and the type reference
N/A
Mechanism
N/A
The tests may be carried out on a separate sample
N/A
15
Insulation resistance and dielectric strength
N/A
15.1
Not applicable
N/A
15.2
Not applicable
N/A
15.3
Applicable for full disconnection and microdisconnection
N/A
17
Endurance
N/A
Compliance is checked on three separate appliances
or switches
N/A
For 17.2.4.4, the number of cycles is 10 000, unless
otherwise specified in 24.1.3 of the relevant part 2 of
IEC 60335
N/A
Switches for operation under no load and which can
be operated only by a tool and switches operated by
hand that are interlocked so that they cannot be
operated under load, are not subjected to the tests
N/A
Subclause 17.2.5.2 is not applicable
N/A
Temperature rise of the terminals not more than 30 K
above the temperature rise measured in clause 11 of
IEC 60335-1
N/A
Clearances, creepage distances, solid insulation and coatings of rigid printed board
assemblies
N/A
8
13
20
TRF No. IEC60335_2_80C
Result - Remark
Verdict
TRF originator: KEMA
Page 60 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
This clause is applicable to clearances and creepage
distances for functional insulation, across full
disconnection and micro-disconnection, as stated in
table 24
N/A
ANNEX I (NORMATIVE)
MOTORS HAVING BASIC INSULATION THAT IS INADEQUATE FOR THE RATED
VOLTAGE OF THE APPLIANCE
N/A
The following modifications to this standard are
applicable for motors having basic insulation that is
inadequate for the rated voltage of the appliance:
N/A
8
Protection against access to live parts
N/A
8.1
Metal parts of the motor are considered to be bare
live parts
N/A
11
Heating
N/A
11.3
Temperature rise of the body of the motor is
determined instead of the temperature rise of the
windings
N/A
11.8
Temperature rise of the body of the motor, where in
contact with insulating material, not exceeding values
in table 3 for the relevant insulating material
N/A
16
Leakage current and electric strength
N/A
16.3
Insulation between live parts of the motor and its
other metal parts not subjected to the test
N/A
19
Abnormal operation
N/A
19.1
The tests of 19.7 to 19.9 not carried out
N/A
19.101
Appliance operated at rated voltage with each of the following fault conditions:
N/A
- short circuit of the terminals of the motor, including
any capacitor incorporated in the motor circuit
N/A
- short circuit of each diode of the rectifier
N/A
- open circuit of the supply to the motor
N/A
- open circuit of any parallel resistor, the motor being
in operation
N/A
Only one fault simulated at a time, the tests carried
out consecutively
N/A
Construction
N/A
I
22
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 61 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
22.101
For class I appliances incorporating a motor supplied
by a rectifier circuit, the d.c. circuit being insulated
from accessible parts of the appliance by double or
reinforced insulation
N/A
Compliance checked by the tests specified for double
and reinforced insulation
N/A
J
5.7
5.7.1
5.7.3
5.9
ANNEX J (NORMATIVE)
COATED PRINTED CIRCUIT BOARDS
Result - Remark
Verdict
N/A
(IEC 60335-1/A2)
Testing of protective coatings of printed circuit
boards carried out in accordance with IEC 60664-3
with the following modifications:
N/A
Conditioning of the test specimens
N/A
When production samples are used, three samples
of the printed circuit board are tested
N/A
Cold
N/A
The test is carried out at -25°C
N/A
Rapid change of temperature
N/A
Severity 1 is specified
N/A
Additional tests
N/A
This subclause is not applicable
K
ANNEX K (NORMATIVE)
OVERVOLTAGE CATEGORIES
P
The information on overvoltage categories is
extracted from IEC 60664-1
P
Overvoltage category is a numeral defining a
transient overvoltage condition
P
Equipment of overvoltage category IV is for use at
the origin of the installation
N/A
Equipment of overvoltage category III is equipment in
fixed installations and for cases where the reliability
and the availability of the equipment is subject to
special requirements
N/A
Equipment of overvoltage category II is energy
consuming equipment to be supplied from the fixed
installation
If such equipment is subjected to special
requirements with regard to reliability and availability,
overvoltage category III applies
TRF No. IEC60335_2_80C
According to the subclause
29.1
P
N/A
TRF originator: KEMA
Page 62 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
N/A
Equipment of overvoltage category I is equipment for
connection to circuits in which measures are taken to
limit transient overvoltages to an appropriate low level
L
M
ANNEX L (INFORMATIVE)
GUIDANCE FOR THE MEASUREMENT OF CLEARANCES AND CREEPAGE
DISTANCES
P
Sequences for the determination of clearances and
creepage distances
P
ANNEX M (NORMATIVE)
POLLUTION DEGREE
P
The information on pollution degrees is extracted
from IEC 60664-1
P
Pollution
P
The microenvironment determines the effect of
pollution on the insulation, taking into account the
microenvironment
P
Means may be provided to reduce pollution at the
insulation by effective enclosures or similar
P
Minimum clearances specified where pollution may
be present in the microenvironment
P
Degrees of pollution in the microenvironment
P
For evaluating creepage distances, the following degrees of pollution in the
microenvironment are established:
P
- pollution degree 1: no pollution or only dry, nonconductive pollution occurs. The pollution has no
influence
N/A
- pollution degree 2: only non-conductive pollution
occurs, except that occasionally a temporary
conductivity caused by condensation is to be
expected
N/A
- pollution degree 3: conductive pollution occurs or
dry non-conductive pollution occurs that becomes
conductive due to condensation that is to be
expected
N
According to the subclause
29.2 of IEC 60335-2-80
P
- pollution degree 4: the pollution generates
persistent conductivity caused by conductive dust or
by rain or snow
N/A
ANNEX N (NORMATIVE)
PROOF TRACKING TEST
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 63 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
The proof tracking test is carried out in accordance
with IEC 60112 with the following modifications:
N/A
5
Test apparatus
N/A
5.1
Electrodes
N/A
The note does not apply
N/A
Test solutions
N/A
Test solution A is used
N/A
6
Procedure
N/A
6.3
Proof tracking test
N/A
5.4
Voltage is 100V, 175V, 400V or 600V......................:
N/A
-
Note 3 of clause 3 applies
N/A
The test is carried out on five specimens
N/A
In case of doubt, additional test with voltage reduced
by 25V, the number of drops increased to 100
N/A
Report
N/A
The report stating if the PTI value was based on a
test using 100 drops with a test voltage of (PTI-25) V
N/A
10.1
The proof voltage is 100 V, 175 V, 400 V or 600 V
N/A
10.2
The report shall state if the PTI value was based on a
test using 100 drops with a test voltage of (PTI-25) V
(IEC 60335-1/A1)
N/A
O
ANNEX O (INFORMATIVE)
SELECTION AND SEQUENCE OF THE TESTS OF CLAUSE 30 (IEC 60335-1/A2)
P
Description of tests for determination of resistance
to heat and fire
P
7
P
ANNEX P (INFORMATIVE)
GUIDANCE FOR THE APPLICATION OF THIS STANDARD TO APPLIANCES
USED IN WARM DAMP EQUABLE CLIMATES
5.7
Ambient temperature during tests of clause 11 and
13 is 40 +/- 3 °C (IEC 60335-1/A1)
N/A
7.1
The appliance shall be marked with the letters
WDaE (IEC 60335-1/A1)
N/A
7.12
The instructions shall state that the appliance is to
be supplied trough a residual current device (RCD)
not exceeding 30 mA (IEC 60335-1/A1)
N/A
15.3
The value of t is 37 °C (IEC 60335-1/A1)
N/A
19.13
The leakage current test of clause 16.2 is applied
N/A
TRF No. IEC60335_2_80C
N/A
TRF originator: KEMA
Page 64 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
(IEC 60335-1/A1)
R
ANNEX R (INFORMATIVE) SOFTWARE EVALUATION ACCORDING TO
60730-1
H.2
Only definitions H.2.16 to H.2.20 are applicable
(IEC 60335-1/A1)
N/A
H.11.12
All the subclauses of H.11.12 as modified are
applicable (IEC 60335-1/A1)
N/A
H.11.12.7.
1
For appliances using software class C having a
single channel with self-test monitoring structure,
the manufacturer shall provide measures
(IEC 60335-1/A1)
N/A
H.11.12.8
Software fault/error detection shall occur before
compliance with clause 19.13 is impaired
(IEC 60335-1/A1)
N/A
H.11.12.13 Software and safety related hardware under its
control shall initialize and terminate before
compliance with clause 19.13 is impaired
(IEC 60335-1/A1)
TRF No. IEC60335_2_80C
IEC
N/A
N/A
TRF originator: KEMA
Page 65 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
10.1
TABLE: Power input deviation
Input deviation of/at:
Result - Remark
Verdict
P
P rated (W)
P measured
(W)
dP
Required dP
Remark
VENTS 100 MVTH
14
16
2W
+ 2,8 W
See below
VENTS 125 M1
16
17,7
1,7 W
+ 3,2 W
See below
VENTS 150 M3TP Q
24
23
–1W
+ 4,8 W
See below
Remark: Maximum value of deviation can be measured at 240 V.
10.2
TABLE: Current deviation
Current deviation of/at:
I rated (A)
N/A
I measured (A)
dI
Required dI
Remark
-
11.8
TABLE: Heating test, thermocouples
P
Test voltage (V) ........................................................:
254

Ambient (°C).............................................................:
45

Thermocouple locations
dT (K)
Max. dT (K)
Terminal block
2
40
Internal wire
2
30
Enclosure
12
according to scl. 30.1
PCB
13
100
Terminal block
2
40
Internal wire
2
30
Enclosure
6
according to scl. 30.1
Terminal block
1
40
Internal wire
2
30
Enclosure
15
according to scl. 30.1
VENTS 100 MVTH
VENTS 125 M1
VENTS 150 M3TP Q
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 66 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Thermocouple locations
Verdict
dT (K)
Max. dT (K)
16
100
PCB
Note(s):
With a rated maximum ambient temperature of 45 °C, the max. temperature rise is calculated as follows:
Winding components:
- Class B (resistance method)
→ ∆Tmax = 95- (45-25) K = 75 K
Surface of components:
- Terminal block
→ ∆Tmax = 60- (45-25) K = 40 K
- Internal wire
→ ∆Tmax = 50- (45-25) K = 30 K
- PCB
→ ∆Tmax = 120- (45-25) K = 100 K
11.8
TABLE: Heating test, resistance method
P
Test voltage (V) ........................................................:
254,4

Ambient, t1 (°C) .........................................................:
45

Ambient, t2 (°C) .........................................................:
45

Temperature rise of winding
R1 (1)
R2 (1)
dT (K)
Max. dT (K)
Insulation
class
VENTS 100 MVTH
809
939
45
75
130
VENTS 125 M1
619
714
55
75
130
VENTS 150 M3TP Q
278
335
27
75
130
13.2
TABLE: Leakage current
P
Heating appliances: 1.15 x rated input ..................:
-

Motor-operated and combined appliances:
1.06 x rated voltage................................................:
254,4

Leakage current between
I (mA)
Max. allowed I (mA)
VENTS 100 MVTH
0,02
0,25
VENTS 125 M1
0,01
0,25
Live and enclosure wrapped with foil:
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 67 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
VENTS 150 M3TP Q
13.3
Verdict
0,02
0,25
TABLE: Electric strength
P
Test voltage applied between:
Voltage (V)
Breakdown
(Yes/No)
Live and motor surface
1000
No
Motor surface and enclosure wrapped with foil
1750
No
Live and enclosure wrapped with foil
3000
No
14
TABLE: Transient overvoltages
Clearance between:
Cl (mm)
N/A
Required
Cl (mm)
Rated impulse
voltage (V)
Impulse test
voltage (V)
Flashover
(Yes/No)
-
16.2
TABLE: Leakage current
P
Single phase appliances: 1.06 x rated voltage ......:
-

Three phase appliances 1.06 x rated voltage
divided by √3: .........................................................:
254,4

Leakage current between
I (mA)
Max. allowed I (mA)
VENTS 100 MVTH
0,01
0,25
VENTS 125 M1
0,01
0,25
VENTS 150 M3TP Q
0,01
0,25
Live and enclosure wrapped with foil:
16.3
TABLE: Electric strength
Test voltage applied between:
P
Voltage (V)
Breakdown
(Yes/No)
Live and motor surface
1250
No
Motor surface and enclosure wrapped with foil
1750
No
Live and enclosure wrapped with foil
3000
No
17
TABLE: Overload protection, temperature rise
TRF No. IEC60335_2_80C
N/A
TRF originator: KEMA
Page 68 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Temperature rise of part/at:
Verdict
dT (K)
Max. dT (K)
-
19.7
TABLE: Abnormal operation, locked rotor/moving parts
Test voltage (V) ........................................................:
240

Ambient, t1 (°C) .........................................................:
25

Ambient, t2 (°C) .........................................................:
25

Temperature of winding
R1 (1)
- (Thermal link operated)
-
19.9
R2 (1)
dT (K)
T (°C)
Max. T (°C)
TABLE: Abnormal operation, running overload
N/A
Test voltage (V) ........................................................:
-

Ambient, t1 (°C) .........................................................:
-

Ambient, t2 (°C) .........................................................:
-

Temperature of winding
19.13
N/A
R1 (1)
R2 (1)
dT (K)
T (°C)
Max. T (°C)
TABLE: Abnormal operation, temperature rises
Thermocouple locations
dT (K)
P
Max. dT (K)
VENTS 100 MVTH
Enclosure
30
According to scl. 30.1
24
According to scl. 30.1
33
According to scl. 30.1
VENTS 125 M1
Enclosure
VENTS 150 M3TP Q
Enclosure
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 69 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
24.1
TABLE: Components
Object / part No. Manufacturer/
trademark
Motor protector
Aupo Electronics
Ltd.
Terminal
SIMET S.A.
Terminal alt.
Heavy Power Co.
Ltd.
PCB
Lamitec - AG
- Capacitor
- Terminal
Switch
Engine
Engine
Engine
Engine
Engine
Engine
Engine
1)
Result - Remark
Verdict
P
Type / model
Technical data
Standard
Mark(s) of
conformity
P7
AC 250V, 150°C
EN 60691
VDE
LTA12-2,5
2,5mm2, 380V
IEC 60998
BBJ
PA8
1,5mm , 450V
2
EN 60998
VDE
LAMPLEX –
FR4
-
CKX
250 V~
DG 340
200, 200/328
Hunan Keli Motor
Ltd.
Chiefcon
Electronics
Degson
VLM S.p.a.
EN 60335-1
EN 60335-2-80
Tested in the
appliance
EN 60384-14
VDE
300 V; 10 A;
250V~ 2 A T 125
EN 60998
EN 61058
VDE
IMQ
BL 58-12A01
220-240V~ 50Hz
EN 60335-1
EN 60335-2-80
Tested in the
appliance
Hunan Keli Motor
Ltd.
BL 58-16A01
220-240V~ 50Hz
EN 60335-1
EN 60335-2-80
Tested in the
appliance
Hunan Keli Motor
Ltd.
BL 58-30A01
220-240V~ 50Hz
EN 60335-1
EN 60335-2-80
Tested in the
appliance
CIXI CITI
YIXIONG
ELECTROMOTO
R FACTORY
BL 58-12Y03
220-240V~ 50Hz
EN 60335-1
EN 60335-2-80
Tested in the
appliance
BL 58-16Y03
220-240V~ 50Hz
EN 60335-1
EN 60335-2-80
Tested in the
appliance
BL 58-30Y03
220-240V~ 50Hz
EN 60335-1
EN 60335-2-80
Tested in the
appliance
BL 58-20A01
220-240V~ 50Hz
EN 60335-1
EN 60335-2-80
Tested in the
appliance
CIXI CITI
YIXIONG
ELECTROMOTO
R FACTORY
CIXI CITI
YIXIONG
ELECTROMOTO
R FACTORY
Hunan Keli Motor
Ltd.
An asterisk indicates a mark which assures the agreed level of surveillance
28.1
TABLE: Threaded part torque test
TRF No. IEC60335_2_80C
P
TRF originator: KEMA
Page 70 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Threaded part identification
Result - Remark
Diameter of thread
(mm)
Column number
(I, II, or III)
Applied torque (Nm)
5,8
II
2,5
Motor holder screw
29.1
Verdict
TABLE: Clearances
P
Overvoltage category.... :

Type of insulation:
Rated impulse
voltage (V):
Min. cl
(mm)
330
0,5
500
0,5
800
0,5
1 500
1,0
2 500
2,0
4 000
3,5
6 000
6,0
8 000
8,5
10 000
11,5
29.2
Basic
Functional
Supplementary
3
2,5
4,6
Reinforced
Verdict / Remark
P
7,6
P / between live and
accessible part of enclosure
TABLE: Creepage distances, basic, supplementary and reinforced insulation
P
Creepage distance
(mm)
Pollution degree
Working voltage
(V)
1
2
3
Material group
Material group
I
II
IIIa/IIIb
I
II
Type of insulation
IIIa/IIIb
B*)
>50
0,2
0,6
0,9
1,2
1,5
1,7
1,9
>50
0,2
0,6
0,9
1,2
1,5
1,7
1,9

>50
0,4
1,2
1,8
2,4
3,0
3,4
3,8

>50 and ≤125
0,3
0,8
1,1
1,5
1,9
2,1
2,4
TRF No. IEC60335_2_80C
S*)
R*)


P
Verdict




TRF originator: KEMA
Page 71 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
>50 and ≤125
0,3
0,8
1,1
1,5
1,9
2,1
2,4

>50 and ≤125
0,6
1,6
2,2
3,0
3,8
4,2
4,8


>125 and ≤250
0,6
1,3
1,8
2,5
3,2
3,6
4,0
5


>125 and ≤250
0,6
1,3
1,8
2,5
3,2
3,6
4,0

9

P
>125 and ≤250
1,2
2,6
3,6
5,0
6,4
7,2
8,0


12
P
>250 and ≤400
1,0
2,0
2,8
4,0
5,0
5,6
6,3


>250 and ≤400
1,0
2,0
2,8
4,0
5,0
5,6
6,3

>250 and ≤400
2,0
4,0
5,6
8,0
10,0
11,2
12,6

>400 and ≤500
1,3
2,5
3,6
5,0
6,3
7,1
8,0
>400 and ≤500
1,3
2,5
3,6
5,0
6,3
7,1
8,0

>400 and ≤500
2,6
5,0
7,2
10,0
12,6
14,2
16,0

>500 and ≤800
1,8
3,2
4,5
6,3
8,0
9,0
10,0
>500 and ≤800
1,8
3,2
4,5
6,3
8,0
9,0
10,0

>500 and ≤800
3,6
6,4
9,0
12,6
16,0
18,0
20,0

>800 and ≤1000
2,4
4,0
5,6
8,0
10,0
11,0
12,5
>800 and ≤1000
2,4
4,0
5,6
8,0
10,0
11,0
12,5

>800 and ≤1000
4,8
8,0
11,2
16,0
20,0
22,0
25,0

>1000 and ≤1250
3,2
5,0
7,1
10,0
12,5
14,0
16,0
>1000 and ≤1250
3,2
5,0
7,1
10,0
12,5
14,0
16,0

>1000 and ≤1250
6,4
10,0
14,2
20,0
25,0
28,0
32,0

>1250 and ≤1600
4,2
6,3
9,0
12,5
16,0
18,0
20,0
>1250 and ≤1600
4,2
6,3
9,0
12,5
16,0
18,0
20,0

>1250 and ≤1600
8,4
12,6
18,0
25,0
32,0
36,0
40,0

>1600 and ≤2000
5,6
8,0
11,0
16,0
20,0
22,0
25,0
>1600 and ≤2000
5,6
8,0
11,0
16,0
20,0
22,0
25,0

>1600 and ≤2000
11,2
16,0
22,0
32,0
40,0
44,0
50,0

>2000 and ≤2500
7,5
10,0
14,0
20,0
25, 0
28,0
32,0
>2000 and ≤2500
7,5
10,0
14,0
20,0
25, 0
28,0
32,0

>2000 and ≤2500
15,0
20,0
28,0
40,0
50,0
56,0
64,0

>2500 and ≤3200
10,0
12,5
18,0
25,0
32,0
36,0
40,0
>2500 and ≤3200
10,0
12,5
18,0
25,0
32,0
36,0
40,0
TRF No. IEC60335_2_80C

(1)
(2)
































P


TRF originator: KEMA
Page 72 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark

>2500 and ≤3200
20,0
25,0
36,0
50,0
64,0
72,0
80,0
>3200 and ≤4000
12,5
16,0
22,0
32,0
40,0
45,0
50,0
>3200 and ≤4000
12,5
16,0
22,0
32,0
40,0
45,0
50,0

>3200 and ≤4000
25,0
32,0
44,0
64,0
80,0
90,0
100,0

>4000 and ≤5000
16,0
20,0
28,0
40,0
50,0
56,0
63,0
>4000 and ≤5000
16,0
20,0
28,0
40,0
50,0
56,0
63,0

>4000 and ≤5000
32,0
40,0
56,0
80,0
100,0 112,0
126,0

>5000 and ≤6300
20,0
25,0
36,0
50,0
63,0
71,0
80,0
>5000 and ≤6300
20,0
25,0
36,0
50,0
63,0
71,0
80,0

>5000 and ≤6300
40,0
50,0
72,0
100,0
126,0 142,0
160,0

>6300 and ≤8000
25,0
32,0
45,0
63,0
80,0
90,0
100,0
>6300 and ≤8000
25,0
32,0
45,0
63,0
80,0
90,0
100,0

>6300 and ≤8000
50,0
64,0
90,0
126,0
160,0 180,0
200,0

>8000 and ≤10000
32,0
40,0
56,0
80,0
100,0 110,0
125,0
>8000 and ≤10000
32,0
40,0
56,0
80,0
100,0 110,0
125,0

>8000 and ≤10000
64,0
80,0
112,0
160,0
200,0 220,0
250,0

>10000 and ≤12500 40,0
50,0
71,0
100,0
125,0 140,0
160,0
>10000 and ≤12500 40,0
50,0
71,0
100,0
125,0 140,0
160,0

>10000 and ≤12500 80,0
100,0
142,0
200,0
250,0 280,0
320,0

Verdict

























)
* , B=Basic, S=Supplementary and R=Reinforced
(1)
: between motor body and accessible part of enclosure
: Between live and accessible part of enclosure
(2)
29.2
TABLE: Creepage distances, functional insulation
P
Creepage distance
(mm)
Pollution degree
Working voltage
(V)
1
2
3
Material group
Material group
I
II
IIIa/IIIb
I
II
IIIa/IIIb
>50
0,2
0,6
0,8
1,1
1,4
1,6
1,8
>50 and ≤125
0,3
0,7
1,0
1,4
1,8
2,0
2,2
TRF No. IEC60335_2_80C
Verdict / Remark
TRF originator: KEMA
Page 73 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
>125 and ≤250
0,4
1,0
1,4
2,0
2,5
2,8
3,2
>250 and ≤400
0,8
1,6
2,2
3,2
4,0
4,5
5,0
>400 and ≤500
1,0
2,0
2,8
4,0
5,0
5,6
6,3
>500 and ≤800
1,8
3,2
4,5
6,3
8,0
9,0
10,0
>800 and ≤1000
2,4
4,0
5,6
8,0
10,0
11,0
12,5
>1000 and ≤1250
3,2
5,0
7,1
10,0
12,5
14,0
16,0
>1250 and ≤1600
4,2
6,3
9,0
12,5
16,0
18,0
20,0
>1600 and ≤2000
5,6
8,0
11,0
16,0
20,0
22,0
25,0
>2000 and ≤2500
7,5
10,0
14,0
20,0
25,0
28,0
32,0
>2500 and ≤3200
10,0
12,5
18,0
25,0
32,0
36,0
40,0
>3200 and ≤4000
12,5
16,0
22,0
32,0
40,0
45,0
50,0
>4000 and ≤5000
16,0
20,0
28,0
40,0
50,0
56,0
63,0
>5000 and ≤6300
20,0
25,0
36,0
50,0
63,0
71,0
80,0
>6300 and ≤8000
25,0
32,0
45,0
63,0
80,0
90,0
100,0
>8000 and ≤10000
32,0
40,0
56,0
80,0
100,0 110,0
125,0
>10000 and ≤12500 40,0
50,0
71,0
100,0
125,0 140,0
160,0
30.1
Verdict
P
TABLE: Ball pressure
Part
Enclosure
TRF No. IEC60335_2_80C
P
Test temperature (°C)
Impression diameter
(mm)
Allowed impression
diameter (mm)
75
0.8
2
TRF originator: KEMA
Page 74 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
Group/CENELEC Common Differences to IEC 60335-1:2001 (4. Edition)
6.1
Delete “class 0” and “class 01”
P
7.1
Single-phase appliances to be connected to the
supply mains: 230 V covered
P
25.6
25.7
25.7
Multi-phase appliances to be connected to the supply
mains: 400 V covered
N/A
Supply cords of single-phase portable appliances having a rated current not exceeding
16 A, fitted with a plug complying with the following standard sheets of
IEC 60083:1975:
N/A
- for Class I appliances: standard sheet C2b, C3b or
C4 ............................................................................:
-
N/A
- for Class II appliances: standard sheet C5 or C6..:
-
N/A
Additional type of supply cord:
N/A
- ordinary polychloroprene sheathed flexible cord
(60245 IEC 57)
N/A
Supply cords having high flexibility, not lighter than:
N/A
- rubber insulated and sheathed cord (60245 IEC 86)
N/A
- rubber insulated, crosslinked PVC sheathed cord
(60245 IEC 87)
N/A
- crosslinked PVC insulated and sheathed cord
(60245 IEC 88)
N/A
P
29.3
The third dashed item replaced by:
- an assessment of the thermal quality of the material
combined with an electric strength test, in
accordance with 29.3.3, and, for accessible
reinforced insulation consisting of a single layer,
measurement in accordance with 29.3.Z1
29.3.Z1
For accessible reinforced insulation consisting of a
single layer, the thickness of the layer complies with
table Z1; rated voltage (V); overvoltage category;
thickness (mm) .........................................................:
Annex ZC
ANNEX ZC (NORMATIVE)
NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH THEIR
CORRESPONDING EUROPEAN PUBLICATIONS
P
A list of referenced documents in this standard
P
Annex ZD
240 V; II; 2;
ANNEX ZD (INFORMATIVE)
IEC and CENELEC CODE DESIGNATIONS FOR FLEXIBLE CORDS
TRF No. IEC60335_2_80C
P
N/A
TRF originator: KEMA
Page 75 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
A list of code designations for different types of
flexible cords
Verdict
N/A
National Differences for Austria
25.6
Plugs according to standard sheet C3b not allowed
N/A
National Differences for Belgium
25.6
Plugs according to standard sheet C2b not allowed
TRF No. IEC60335_2_80C
N/A
TRF originator: KEMA
Page 76 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
National Differences for Denmark
7.12
Requirements regarding marking tag of power supply
cord and connection of earthing wire for class I
appliances delivered without a plug
N/A
25.6
Supply cords of single-phase portable appliances
having a rated current not exceeding 13 A provided
with a plug according to the following:
N/A
Class I appliances: Section 107-2-D1, ed.3 1998,
Standard Sheet DK 2-1a
N/A
For appliances covered by a Part 2 of EN 60335,
also plugs in accordance with Section 107-2-D1, ed.
3, 1998, Standard Sheet C2b, C3b or C4 are allowed
N/A
Class II appliances: Section 107-2-D1, ed.3 1998,
Standard Sheet C1b, C5, C6, DKA 2-1a and DKA 21b
N/A
Stationary single-phase appliances, having a rated
current not exceeding 13 A, and provided with a
supply cord and a plug, the plug is in accordance with
the requirements above
N/A
Multi-phase appliances and single-phase appliances
having a rated current exceeding 13 A, and provided
with a supply cord and a plug, the plug is in
accordance with the requirements below:
N/A
Class I appliances: Section 107-2-D1, Standard
Sheet DK 6-1a / EN 60309-2, Standard Sheet 2-II,
2-IV
N/A
Class II appliances: Section 107-2-D1, Standard
Sheet DK 6-1a / EN 60309-2, Standard Sheet 2-II,
2-IV, the earthing contact not being connected
N/A
The current for the plug not exceeding the values
specified; standard sheet (no.); current (A) ............:
-
N/A
National Differences for Finland
25.6
Plugs according to standard sheet C3b not allowed
TRF No. IEC60335_2_80C
N/A
TRF originator: KEMA
Page 77 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
National Differences for France
22.2
The second paragraph of this subclause, dealing with
single-phase, permanently connected class I
appliances having heating elements, is not applicable
due to the supply system
N/A
25.6
Plugs according to standard sheet C2b not allowed
N/A
National Differences for Germany
25.6
Plugs according to standard sheet C3b not allowed
29.3
Third dashed item not applicable for appliances
where the insulation is accessible. Additional
measures, such as a multi-layered insulation or
adequate thickness, taken.
N/A
P
National Differences for Iceland
25.6
Plugs according to standard sheet C3b not allowed
N/A
National Differences for Ireland
25.6
Plugs according to standard sheet C3b not allowed
N/A
25.6
Only plugs according to Standard Sheets B2 and C5
allowed
N/A
25.6
These regulations apply to all plugs for domestic use
at a voltage of not less than 200 V and allow only
plugs complying with I.S. 401:1997, or equivalent, to
be fitted to domestic appliances.
N/A
25.8
Replacement of figures (rated current/cross-sectional
area) in the table
N/A
National Differences for Italy
7.1
The voltage is 220 V/380 V
N/A
25.6
Plugs according to standard sheet C3b not allowed
N/A
25.6
Only plugs listed in CENELEC Report R0BT005:2001 allowed
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 78 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
National Differences for Luxembourg
25.6
Plugs according to standard sheet C3b not allowed
N/A
National Differences for Netherlands
25.6
Plugs according to standard sheet C3b not allowed
N/A
National Differences for Norway
19.5
The test is also applicable to appliances intended to
be permanently connected to fixed wiring
N/A
22.2
The second paragraph of this subclause, dealing with
single-phase, permanently connected class I
appliances having heating elements, is not applicable
due to the supply system
N/A
25.6
Plugs according to standard sheet C3b not allowed
N/A
National Differences for Portugal
25.6
Plugs according to standard sheet C3b not allowed
N/A
National Differences for Spain
25.6
Plugs according to standard sheet C2b not allowed
N/A
25.6
Plugs according to standard sheet C3b not allowed
N/A
25.6
For appliances for household use, only the following
plugs are allowed:
N/A
according to UNE 20315: ESC 10-1b, C2b, C4, C6 or
ESB 25-5b
N/A
according to UNE-EN 50075
N/A
N/A
National Differences for Sweden
25.6
Plugs according to standard sheet C3b not allowed
TRF No. IEC60335_2_80C
N/A
TRF originator: KEMA
Page 79 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
National Differences for Switzerland
4
Information about batteries with carbon-zinc and
alkali-manganese
N/A
25.6
Plugs according to standard sheet C3b not allowed
N/A
25.6
Supply cords of portable household and similar
electrical appliances having a rated current not
exceeding 10 A, provided with a plug complying with
SEV 1011 or IEC 60884-1 and one of the following
dimension sheets:
N/A
SEV 6532-2.1991, plug type 15, 3P+N+PE,
250/400 V, 10 A
N/A
SEV 6533-2.1991, plug type 11, L+N, 250 V, 10 A
N/A
SEV 6534-2.1991 plug type 12, L+N+PE, 250 V, 10 A
N/A
National Differences for United Kingdom
25.6
Plugs according to standard sheet C2b not allowed
N/A
25.6
Plugs according to standard sheet C3b not allowed
N/A
25.6
Only plugs according to Standard Sheets B2 and C5
allowed
N/A
25.6
These regulations apply to all plugs for domestic use
at a voltage of not less than 200 V and allow only
plugs to BS 1363 to be fitted to domestic appliances.
It also allows plugs to BS 4573 and standard sheet
C5 to be fitted to shavers and toothbrushes.
N/A
25.8
Replacement of figures (rated current/cross-sectional
area) in the table
N/A
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 80 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
Pictures of the appliances
VENTS 100 MVTH
VENTS 100 MVTH
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 81 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
VENTS 100 MVTH
VENTS 100 MVTH
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 82 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
VENTS 100 MVTH inside
VENTS 125 M1
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 83 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
VENTS 125 M1
VENTS 125 M1
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 84 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
VENTS 125 M1
VENTS 150 M3 TP Q
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 85 of 85
Report No.: 28210042 001
IEC 60335-2-80
Clause
Requirement + Test
Result - Remark
Verdict
VENTS 150 M3 TP Q
VENTS 150 M3 TP Q
TRF No. IEC60335_2_80C
TRF originator: KEMA
Page 1of 8
Report No.: 28210042 001
IEC60335_2_80C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
ATTACHMENT TO TEST REPORT IEC 60335-2-80
EUROPEAN GROUP DIFFERENCES AND NATIONAL DIFFERENCES
(Part 2: Particular requirements for Drives for fans)
Differences according to................:
EN 60335-2-80: 2003 +A1: 2004 + A2 :2009
EN 60335-1: 2002+A1: 2004 + A11: 2004 + A2: 2006 + A12: 2006 +
A13: 2008
EN 62233: 2008
Attachment Form No......................:
EU_GD_IEC60335_2_80C
Attachment Originator ...................:
KEMA Quality B.V.
Master Attachment .........................:
Dated 2009-10
Copyright © 2009 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
CENELEC COMMON MODIFICATIONS (EN)
P
6.1
Delete “class 0” and “class 01”
P
7.1
Single-phase appliances to be connected to the
supply mains: 230 V covered
P
Multi-phase appliances to be connected to the
supply mains: 400 V covered
N/A
21.101
Add: The test probe is applied with a force not
exceeding 5 N. (EN 60335-2-80/A2)
P
24.1.7
If the remote operation of the appliance is via a
telecommunication network, the relevant standards
for the telecommunication interface circuitry in the
appliance are EN 41003 and EN 60950-1:2006,
Subclause 6.3.
N/A
25.6
Supply cords of single-phase portable appliances having a rated current not
exceeding 16 A, fitted with a plug complying with the following standard sheets of
IEC 60083:1975:
N/A
- for Class I appliances: standard sheet C2b, C3b or C4 ....................................................................... :
N/A
- for Class II appliances: standard sheet C5 or C6 : -
N/A
Additional type of supply cord:
N/A
- ordinary polychloroprene sheathed flexible cord
(60245 IEC 57)
N/A
Supply cords having high flexibility, not lighter than:
N/A
- rubber insulated and sheathed cord
(60245 IEC 86)
N/A
25.7
25.7
Page 2of 8
Report No.: 28210042 001
IEC60335_2_80C – ATTACHMENT 1
Clause
29.3
Requirement + Test
Result - Remark
Verdict
- rubber insulated, crosslinked PVC sheathed cord
(60245 IEC 87)
N/A
- crosslinked PVC insulated and sheathed cord
(60245 IEC 88)
N/A
The third dashed item replaced by:
- an assessment of the thermal quality of the
material combined with an electric strength test, in
accordance with 29.3.3, and, for accessible
reinforced insulation consisting of a single layer,
measurement in accordance with 29.3.Z1
P
Page 3of 8
Report No.: 28210042 001
IEC60335_2_80C – ATTACHMENT 1
Clause
Requirement + Test
29.3.Z1
For accessible reinforced insulation consisting of a 240 V; II; 2;
single layer, the thickness of the layer complies
with table Z1; rated voltage (V); overvoltage
category; thickness (mm) ........................................ :
P
ZC
ANNEX ZC, NATIONAL DEVIATIONS (EN)
NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH THEIR
CORRESPONDING EUROPEAN PUBLICATIONS
P
A list of referenced documents in this standard
P
ZD
Result - Remark
Verdict
ANNEX ZD, INFORMATIONS(EN)
IEC and CENELEC CODE DESIGNATIONS FOR
FLEXIBLE CORDS
N/A
A list of code designations for different types of
flexible cords
N/A
National Differences for Austria
25.6
Plugs according to standard sheet C3b not allowed
N/A
National Differences for Belgium
25.6
Plugs according to standard sheet C2b not allowed
N/A
Page 4of 8
Report No.: 28210042 001
IEC60335_2_80C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
National Differences for Denmark
7.12
Requirements regarding marking tag of power
supply cord and connection of earthing wire for class
I appliances delivered without a plug
N/A
25.6
Supply cords of single-phase portable appliances
having a rated current not exceeding 13 A provided
with a plug according to the following:
N/A
Class I appliances: Section 107-2-D1, ed.3 1998,
Standard Sheet DK 2-1a
N/A
For appliances covered by a Part 2 of EN 60335,
also plugs in accordance with Section 107-2-D1, ed.
3, 1998, Standard Sheet C2b, C3b or C4 are
allowed
N/A
Class II appliances: Section 107-2-D1, ed.3 1998,
Standard Sheet C1b, C5, C6, DKA 2-1a and DKA 21b
N/A
Stationary single-phase appliances, having a rated
current not exceeding 13 A, and provided with a
supply cord and a plug, the plug is in accordance
with the requirements above
N/A
Multi-phase appliances and single-phase appliances
having a rated current exceeding 13 A, and provided
with a supply cord and a plug, the plug is in
accordance with the requirements below:
N/A
Class I appliances: Section 107-2-D1, Standard
Sheet DK 6-1a / EN 60309-2, Standard Sheet 2-II,
2-IV
N/A
Class II appliances: Section 107-2-D1, Standard
Sheet DK 6-1a / EN 60309-2, Standard Sheet 2-II,
2-IV, the earthing contact not being connected
N/A
The current for the plug not exceeding the values
specified; standard sheet (no.); current (A) ............:
N/A
National Differences for Finland
25.6
Plugs according to standard sheet C3b not allowed
N/A
Page 5of 8
Report No.: 28210042 001
IEC60335_2_80C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
National Differences for France
22.2
The second paragraph of this subclause, dealing
with single-phase, permanently connected class I
appliances having heating elements, is not
applicable due to the supply system
N/A
25.6
Plugs according to standard sheet C2b not allowed
N/A
National Differences for Germany
25.6
Plugs according to standard sheet C3b not allowed
29.3
Third dashed item not applicable for appliances
where the insulation is accessible. Additional
measures, such as a multi-layered insulation or
adequate thickness, taken.
N/A
P
National Differences for Iceland
25.6
Plugs according to standard sheet C3b not allowed
N/A
National Differences for Ireland
25.6
Plugs according to standard sheet C3b not allowed
N/A
25.6
Only plugs according to Standard Sheets B2 and C5
allowed
N/A
25.6
These regulations apply to all plugs for domestic use
at a voltage of not less than 200 V and allow only
plugs complying with I.S. 401:1997, or equivalent, to
be fitted to domestic appliances.
N/A
25.8
Replacement of figures (rated current/crosssectional area) in the table
N/A
National Differences for Italy
7.1
The voltage is 220 V/380 V
N/A
25.6
Plugs according to standard sheet C3b not allowed
N/A
25.6
Only plugs listed in CENELEC Report R0BT005:2001 allowed
N/A
Page 6of 8
Report No.: 28210042 001
IEC60335_2_80C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
National Differences for Luxembourg
25.6
Plugs according to standard sheet C3b not allowed
N/A
National Differences for Netherlands
25.6
Plugs according to standard sheet C3b not allowed
N/A
National Differences for Norway
19.5
The test is also applicable to appliances intended to
be permanently connected to fixed wiring
N/A
22.2
The second paragraph of this subclause, dealing
with single-phase, permanently connected class I
appliances having heating elements, is not
applicable due to the supply system
N/A
25.6
Plugs according to standard sheet C3b not allowed
N/A
National Differences for Portugal
25.6
Plugs according to standard sheet C3b not allowed
N/A
National Differences for Spain
25.6
Plugs according to standard sheet C2b not allowed
N/A
25.6
Plugs according to standard sheet C3b not allowed
N/A
25.6
For appliances for household use, only the following
plugs are allowed:
N/A
according to UNE 20315: ESC 10-1b, C2b, C4, C6
or ESB 25-5b
N/A
according to UNE-EN 50075
N/A
N/A
National Differences for Sweden
25.6
Plugs according to standard sheet C3b not allowed
N/A
Page 7of 8
Report No.: 28210042 001
IEC60335_2_80C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
National Differences for Switzerland
4
Information about batteries with carbon-zinc and
alkali-manganese
N/A
25.6
Plugs according to standard sheet C3b not allowed
N/A
25.6
Supply cords of portable household and similar
electrical appliances having a rated current not
exceeding 10 A, provided with a plug complying with
SEV 1011 or IEC 60884-1 and one of the following
dimension sheets:
N/A
SEV 6532-2.1991, plug type 15, 3P+N+PE,
250/400 V, 10 A
N/A
SEV 6533-2.1991, plug type 11, L+N, 250 V, 10 A
N/A
SEV 6534-2.1991 plug type 12, L+N+PE, 250 V,
10 A
N/A
National Differences for United Kingdom
25.6
Plugs according to standard sheet C2b not allowed
N/A
25.6
Plugs according to standard sheet C3b not allowed
N/A
25.6
Only plugs according to Standard Sheets B2 and C5
allowed
N/A
25.6
These regulations apply to all plugs for domestic use
at a voltage of not less than 200 V and allow only
plugs to BS 1363 to be fitted to domestic appliances.
It also allows plugs to BS 4573 and standard sheet
C5 to be fitted to shavers and toothbrushes.
N/A
25.8
Replacement of figures (rated current/crosssectional area) in the table
N/A
Page 8of 8
Report No.: 28210042 001
IEC60335_2_80C – ATTACHMENT 1
Clause
Requirement + Test
Result - Remark
Verdict
ANNEX EMF
The Tested product also complies to the requirements of EN 62233:2008

Limit ……………100%
P
Appliance is classified as
'benign' appliance based on
OSM/HA(WG-EMF)01/07
documents so the appliance is
in accordance with EMF
requirement according to EN
62233:2008 without testing.
Mér1eszköz lista
Measuring equipment list
www.tuv.com
Melléklet 2 / Attachment 2
Jegyz1könyv szám / Test report No. 28210042 001
Mér1eszköz
Measuring equipment
Gyártó
Manufacturer
Típus
Type
Oldal / Page 1 / 1
Leltári sz. / széria sz. Köv. kalibráció
Inventory / Serial No. Next calibration
Dielectric strength tester
ELABO
90-1F
23138
09. 2010.
Ohm meter
Ganz
DKE
0570632051
10. 2010.
Leakage current measurer
HIOKI
3156
2041/23317
08. 2011.
Wattmeter
Norma
D 1150
023066
08. 2011.
Data acquisition system
DATCON
DT9040
023268
11. 2010.
Torque screwdriver
Facom
A301A
60044
10. 2010.
Glow wire test equipment
PTL
MEEI KFT
T 03.34
22196
06. 2011.
-
023031
07. 2013.
Test probe 13 of IEC 61032 MEEI KFT
-
023031
07. 2013.
Caliper
Mitutoyo
CD-15B
0556014008
06. 2011.
Spring hammer
NEMKO
0,5Nm
22869
07. 2011.
Force meter spring
ERICHSEN
0-50N
0570550051
07. 2011.
Heating chamber
Heraeus
UT 6120
022308
03. 2011.
Test probe B of IEC 61032
Megjegyzés / Remark: –
F 27-X1_1_0
Page 1/1
2007.07.10-t1l
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement