MX-206 Data Sheet

MX-206 Data Sheet
MX-206 Stereo Microphone Mixer
TECHNICAL NOTES & SPECIFICATIONS
Features
ARCHITECTS SPECIFICATIONS
MX-206
The unit shall be a six input stereo microphone mixer with TRS stereo outputs as well
as a transformer-isolated +24 dBm , 600 ohm
balanced XLR mono output. There shall be
+48 volts of phantom power available for condenser microphones, with gradual power-up
and down of this phantom power to eliminate
any transient spikes. Total voltage gain measured from each microphone input to the Main
Outputs shall be a minimum of 84dB. Each of
the six microphone channels shall have 40dB
of adjustable gain via a front panel 3 position
slide switch. Each input shall also have a 20dB
pad switch on the rear of the unit, making
a total of 60dB of possible gain/attenuation.
Each channel shall have a continuously variable pan control. There shall be a peak Clip
LED indicator on each input channel which
shall illuminate when the input is 3dB below
true clipping, and another Clip indicator on
the output of the mixer which shall illuminate
when the output is within 3dB of actual clipping. Two 6-segment LED meters must be
provided to monitor the mixer output, calibrated for 0 VU to equal +4 dbu. There shall
be a separate stereo aux input with front
panel level control, having rear panel connection via RCA phono jacks. There shall also
be a separate stereo aux output available on
the rear panel with access via RCA phono
jacks. Distortion shall be less than 0.02 %
Total Harmonic Distortion at +20dBu (20Hz to
20kHz) and less than 0.05% Intermodulation
Distortion (SMPTE) at +20 dBu (input switch
at -40dB). Hum and Noise shall be less than
-100dBu residual output noise when all levels
are set at minimum. Frequency Response shall
be +0/-.5dB, 20 Hz-20 kHz. Crosstalk of the
unit shall be less than -60dB when measuring
adjacent inputs or input to output at 20kHz.
Dimensions of the model shall be 19” wide
x 1.75” high x 6.6” deep. The mixer shall be
made in America, with a 10 pound shipping
weight.
The mixer shall be the model MX-206,
manufactured by Ashly Audio, Inc. of Webster,
New York. No other unit shall be acceptable
unless data submitted from an independent
test laboratory verifies that the above specifications are met.
• High Gain (84dB Channel Input to
Program Output) Ensures Full Output
with Low Level or Distant Mics
• Transformer Isolated +24dBm 600
ohm Balanced XLR Mono Output
• Pan Control on Each Channel
• +48V Phantom Power for Condenser
Mics
• Auxillary Tape/CD Inputs and Outputs
• Front Panel 3.5mm Stereo Line In Jack
• Stereo Headphone Jack with Level
Control
• Safety/Compliance: cTUVus/CE, RoHS, FCC
Specifications MX-206:
(unless otherwise stated, specification conditions are 150Ω source, all levels nominal, outputs into 2.7KΩ or greater)
Total Harmonic Distortion:
< 0.05 % @ +20 dBu, 20 Hz-20 KHz; input switch at -40dB
IMD (SMPTE IM distortion):
< 0.02 % @ +20 dBu, input switch at -40dB
HUM & NOISE: (20 Hz-20 KHz noise bandwidth, input switch at -60dB)
< -127 dBu equivalent input hum and noise
< -100 dBu residual output noise TRS all level controls minimum
< -90 dBu residual output noise XLR all level controls minimum
< -84 dBu Main Out, Main Level at nominal, all Ch. Level controls at min
< -80 dBu Main Out; Main Level and one Ch. Level at nominal
FREQUENCY RESPONSE:
20 Hz-20 KHz, +0/-0.5 dB
MAXIMUM VOLTAGE GAIN:
84 ± 2 dB: MIC INPUT to MAIN OUTPUT
34 ± 2 dB: AUX INPUT to MAIN OUTPUT
CROSSTALK:
< -60 dB @ 20KHz, between any inputs or outputs
VU METER:
Two 6-segment LED meters, 0 VU = +4 dBu
PEAK INDICATORS:
Peak CLIP indicator on each input channel and on outputs, illuminating 3 dB below clipping
PHANTOM POWER:
+48 VDC applied to all MIC INPUTS, switchable on back panel
80mA maximum total current draw
14mA maximum single current draw
Gradual power-up and down to eliminate “pops.”
POWER REQUIREMENTS:
100 - 240VAC, 50-60 Hz, 30 watts.
DIMENSIONS:
19”L x 1.75”H x 8.0”D
SHIPPING WEIGHT:
13 lbs. maximum
MX-206 Rear Panel
Applications:
Live Sound Reinforcement, Conference Rooms, Lecture Halls, Houses of Worship, Broadcast, Recording, and
Film/Video Production.
Ashly manufactures a complete and comprehensive line of Analog and Digital Signal Processors, Power
Amplifiers, Mixers, and Amplifier Input Options. Please call, write or visit our web site for information on
any of these Ashly Products.
Ashly Audio Inc., 847 Holt Road, Webster, NY 14580-9103
Toll Free (800) 828-6308, Tel: (585) 872-0010, Fax: (585) 872-0739
www.ashly.com, e-mail: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement