Avocent ACS 6000 console server Installation/Administration/User Guide
Реклама
Реклама
For Technical Support: www.avocent.com/support
590-767-501C
Cyclades
®
ACS 6000
Installation/Administration/User Guide
FCC Warning Statement
The Cyclades ACS advanced console server has been tested and found to comply with the limits for Class A digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the Installation and Service Manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user is required to correct the problem at his or her own expense.
Notice about FCC Compliance for All Cyclades ACS Advanced Console Server Models
To comply with FCC standards, the Cyclades ACS advanced console server requires the use of a shielded CAT
5 cable for the Ethernet interface. Notice that this cable is not supplied with either of the products and must be provided by the customer.
Canadian DOC Notice
The Cyclades ACS advanced console server does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
L’Cyclades ACS advanced console server n’émete pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le règlement sur le brouillage radioélectrique edicté par le Ministère des Communications du Canada.
Safety and EMC Approvals and Markings
FCC Class A (USA), CE Class A (EU), ICES-003 (Canada), VCCI (Japan), C-Tick (Australia), A-Tick (Australia, with internal modem), UL 60950-1 (USA), cUL (Canada), EN-60950-1 (EU), CB
Cyclades
®
ACS 6000
Advanced Console Server
Installation/Administration/User
Guide
Avocent, the Avocent logo, The Power of Being There, DSView and
Cyclades are registered trademarks of Avocent Corporation or its affiliates in the US and other countries. All other marks are the property of their respective owners.
© 2009 Avocent Corporation. 590-767-501C
Instructions
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Dangerous Voltage
This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Power On
This symbol indicates the principal on/off switch is in the on position.
Power Off
This symbol indicates the principal on/off switch is in the off position.
Protective Grounding Terminal
This symbol indicates a terminal which must be connected to earth ground prior to making any other connections to the equipment.
iii
T A B L E O F C O N T E N T S
Table of Contents
iv Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager ............ 17
Table of Contents v
Appendix C: Accessing a Console Server with a DSView 3 Software Installation via Dial-up ...... 64
vi Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
vii
L I S T O F F I G U R E S
List of Figures
viii Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
ix
L I S T O F T A B L E S
List of Tables
x Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
C H A P T E R
1
Introduction
The Cyclades ACS 6000 advanced console server is a 1U appliance that serves as a single point for access and administration of connected devices, such as target device consoles, modems and power devices. ACS 6000 console servers support secure remote data center management and out-of-band management of IT assets from any location worldwide.
NOTE: Unless noted, references to the ACS 6000 console server refer to all models in the 60XX series.
ACS 6000 console servers provide secure local (console port) and remote (IP and dial-up) access.
The console servers run the Linux ® operating system with a persistent file system in Flash memory, and can be upgraded from either FTP or a DSView ® 3 management software server.
Multiple administrators can be logged into the console server at the same time and can use the Web
Manager, the Command Line Interface (CLI utility) or DSView 3 software (version 3.6.0.152 and greater) to access and configure the ACS 6000 console server.
Two PC card/slots support modem (V.92 and Wireless GSM/CDMA), Ethernet, fast Ethernet (fiber optic) and storage PC cards (16 bit and 32 bit). One USB port supports modem (V.92 and Wireless
GSM/CDMA), storage devices and USB hubs. Two fast Ethernet ports support connections to more than one network or configuration of Ethernet bonding (failover) for redundancy and greater reliability. For dial-in and secure dial-back with Point-to-Point Protocol (PPP), optional internal modems can be factory installed, or you can use external modems or wireless modem CardBus devices.
Features and Benefits
Access options
Secure access is available through the following local (analog console port) and remote (digital IP and dial-up) options:
• LAN/WAN IP network connection.
• Dial-up to a factory-configured internal modem (optional), a modem connected either to a serial port or the AUX port (which is only possible when an internal modem is not installed), or to a PC phone card (modem, GSM or CDMA) installed in one of the PC card slots or in the
USB port.
1
2 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
• Target device connection. An authorized user can make a Telnet, SSH v1 or SSH v2 connection to a target device through the Web Manager. For Telnet or SSH to be used for target device connections, the Telnet or SSH service must be configured in the security profile that is in effect.
• ACS 6000 console server console connection. An administrator can log in either from a local terminal or from a computer with a terminal emulation program that is connected to the console port and can use the CLI utility. The CLI utility prompt (--|- cli>) displays at login.
More than one administrator can log into the console server and have an active CLI or Web
Manager session. All sessions receive the following warning message when the configuration is changed by another administrator or by the system: The appliance configuration has been altered
from outside of your session. Upon receipt of this message, each administrator needs to verify that changes made during the session were saved.
Web Manager
Users and administrators can perform most tasks through the Web Manager (accessed with HTTP or HTTPS). The Web Manager runs in Internet Explorer ® 6.0 and 7.0, and Firefox ® 2 and 3 on any supported computer that has network access to the console server.
An administrator can use the Web Manager to create user accounts, authorize groups and configure security and ports. Authorized users can access connected devices through the Web Manager to troubleshoot, maintain, cycle power, reboot connected devices and change their password. For more information on the Web Manager, see Chapters 3 and 4.
IPv4 and IPv6 support
The ACS 6000 console server supports dual stack IPv4 and IPv6 protocols. The administrator can use the Web Manager or CLI to configure support for IPv4 addresses only or for both IPv4 and
IPv6 addresses. The following list describes the IPv6 support provided in the console server:
• DHCP
• Dial-in sessions (PPP links)
• DSView software integration
• eth0 and eth1 Ethernet interfaces
• Firewall (IP tables)
• HTTP/HTTPs
• Linux kernel
• Remote authentication: Radius, Tacacs+, LDAP and Kerberos servers
• SNMP
• SSH and Telnet access
• Syslog server
NOTE: Remote authentication NFS, NIS and IPSec are not supported with IPv6.
Chapter 1: Introduction 3
Flexible users and groups
An account can be defined for each user on the console server or on an authentication server. The admin and root users have accounts by default, and either can add and configure other user accounts. Access to ports can be optionally restricted based on authorizations an administrator can assign to custom user groups. For more information, see Users Accounts and User Groups on page
70.
Security
Security profiles determine which network services are enabled on the console server.
Administrators can either allow all users to access enabled ports or allow the configuration of group authorizations to restrict access. You can also select a security profile, which defines which services (FTP, ICMP, IPSec and Telnet) are enabled and SSH and HTTP/HTTPS access. The administrator can select either a preconfigured security profile or create a custom profile. For more information, see Security Configuration on page 65.
Authentication
Authentication can be performed locally, with One Time Passwords (OTP), a remote Kerberos,
LDAP, NIS, RADIUS, TACACS+ authentication server or a DSView 3 server. The console server also supports remote group authorizations for the LDAP, RADIUS and TACACS+ authentication methods. Fallback mechanisms are also available.
Any authentication method configured for the console server or the ports is used for authentication of any user who attempts to log in through Telnet, SSH or the Web Manager. For more information, see Authentication on page 67.
VPN based on IPSec with NAT traversal
If IPSec is enabled in the selected security profile, an administrator can use the VPN feature to enable secure connections. IPSec encryption with optional NAT traversal (which is configured by default) creates a secure tunnel for dedicated communications between the console server and other computers that have IPSec installed. ESP and AH authentication protocols, RSA Public Keys and
Shared Secret are supported. For more information, see IPSec(VPN) on page 81.
Packet filtering
An administrator can configure an ACS 6000 console server to filter packets like a firewall. Packet filtering is controlled by chains, which are named profiles with user-defined rules. The console server filter table contains a number of built-in chains that can be modified but not deleted. An administrator can also create and configure new chains.
SNMP
If SNMP is enabled in the selected security profile, an administrator can configure the Simple
Network Management Protocol (SNMP) agent on the console server to send notifications or traps to an SNMP management application.
4 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
The console server SNMP agent supports SNMP v1/v2 and v3, MIB-II and Enterprise MIB. For more information, see SNMP Configuration on page 82.
NOTE: The text files with the Enterprise MIB (ACS6000-MIB.asn) and the TRAP MIB (ACS6000-TRAP-MIB.asn) are available in the appliance under the /usr/local/mibs directory.
Data logging, notifications, alarms and data buffering
An administrator can set up data logging, notifications and alarms to alert administrators of problems with email, SMS, SNMP trap or DSView 3 software notifications. An administrator can also store buffered data locally, remotely or with DSView 3 management software. Messages about the console server and connected servers or devices can also be sent to syslog servers.
Power management
The ACS 6000 console server enables users who are authorized for power management to turn power on, turn power off and reset devices plugged into a connected power distribution unit (PDU).
The power devices can be connected to any ACS serial port or to the AUX/Modem port (if an internal modem is not installed). For more information, see Power Management on page 86.
Auto discovery
An administrator can enable auto discovery to find the hostname of a serial port. Auto discovery’s default probe and answer strings have a broad range. An administrator can configure site-specific probe and answer strings. Auto discovery can also be configured through DSView 3 software.
Configuration Example
The following graphic and table illustrate a typical ACS 6000 console server configuration.
Chapter 1: Introduction 5
3
4
2
4
5
1
6
7
10
11
8
9
13
12
14
Figure 1.1: Typical ACS 6000 Advanced Console Server Configuration
Table 1.1: Typical ACS 6000 Advanced Console Server Configuration Descriptions
6
7
4
5
2
3
Number Description
1 ACS 6000 advanced console server
Target devices
PDU (one or more)
Serial port connection
PC card (modem, Ethernet or storage)
11
12
Either AUX/Modem or any serial port 13
Modem ordered and configured internally at the factory
-or-
External modem (on a device in one of the PC card slots or USB port, or connected to a serial port or the AUX port)
14
Number Description
8 Phone line
9
10
Remote dial-in client
Local Area Network (LAN)
LAN firewall
Remote authentication server
DSView client/server
Remote/local Windows/Linux computer
6 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
C H A P T E R
2
Installation
Getting Started
Before installing your ACS 6000 console server, refer to the following list to ensure you have all items shipped with the console server, as well as other items necessary for proper installation.
Supplied with the ACS 6000 console server
• Quick Installation Guide (QIG)
• Power Cord
• RJ-45 to RJ-45 straight-through CAT 5 cable
• RJ-45 to DB-9F straight-through adaptor
• Mounting brackets, screws and cord retention clips
• Keyhole mounting kit
• Software License Agreement
Additional items needed
If you are configuring the consoler server in a standalone configuration, you will also need the following items:
• One or more RJ-45 to RJ-45 CAT 5 straight-through cables
• An RJ-45 to DB-9F straight-through adaptor
• A PC running a terminal emulation program
Rack Mounting
You can mount the ACS 6000 console server in a rack or cabinet, or place it on a desktop or other flat surface. For rack or cabinet mounting, two mounting brackets are supplied.
To rack mount the console server:
1.
Install the brackets at the front or back edges of the ACS 6000 console server with the screws provided with the mounting kit.
2.
Mount the console server in a secure position.
7
8 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Figure 2.1: Bracket Connections for Front Mount Configuration
Connecting the Hardware
ACS console server connectors
The following figure shows the connectors on the front of the ACS 6000 console server.
1 2 3
Figure 2.2: Front of the Console Server (ACS 6032 Console Server Shown)
Table 2.1: Connectors on the Console Server Front
2
3
Number
1
Description
USB connector.
PC card slots.
Chapter 2: Installation 9
Table 2.2: LEDs on the Console Server Front
Label
PWR/CPU
ETH 0/ETH 1
AUX/MODEM
Description
Blue
• Blinks - During unit boot
• Solid - During operation
• Off - Power is off
• Amber - Link at 10BaseT speed
• Yellow - Link at 100BaseT speed
• Green - Link at 1000BaseT speed
• Off - No link/cable disconnected/Ethernet fault
Dual LED: Yellow on top, green on bottom
• Yellow - DTR/DCD activity
• Green - TXD and RXD activity
• Off - No activity
[One LED for each serial port] Green
• Blinks - Ready, with activity
• Solid - Ready
• Off - Not ready
The following figure shows the rear connectors on the console server.
3
4
5 6
1 2
Figure 2.3: Rear of the Console Server (ACS 6032 Console Server Shown)
Table 2.3: Connectors on the Console Server Rear
2
3
Number
1
Description
Power supplies (dual AC shown).
Serial ports (32 ports shown). Models come with 4, 8, 16, 32 or 48 serial ports.
ETH 1 10/100M/1G Ethernet port. Can be connected to a second network or used for failover.
10 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Table 2.3: Connectors on the Console Server Rear (Continued)
Number
4
5
6
Description
AUX/Modem port. If an optional internal modem is ordered, this port is defined as a V.92 modem at the factory; otherwise, the port is factory-defined as RS-232 with an RJ-45 ACS console server pinout and can be used to connect either an external modem or a power device.
ETH0 10/100M/1G Ethernet port for remote IP access.
Console port. Allows for local administration and access to connected devices through a terminal or a computer with a terminal emulator.
Connecting device consoles or modems to serial ports
Use CAT 5 or greater cables and DB-9 or DB-25 console adaptors as needed to connect target device consoles or modems to the serial ports on the console server.
The ACS 6000 console server supports the Cisco ® serial port pinout configuration, which is disabled by default. If a Cisco cable is connected to a port, an administrator must enable the Cisco pinout for the port. An administrator can select Expert - Ports - Serial Ports - (SetCAS or
SetPower) - Physical to open the Physical Settings screen, then check Enable Cisco RJ Pin-Out.
The following tables show serial port pinout information.
Table 2.4: ACS Console Server Serial Port Pinout
6
7
4
5
8
2
3
Pin No.
1
Signal Name
RTS
DTR
TxD
GND
CTS
RxD
DCD/DSR
Not Used
Input/Output
OUT
OUT
OUT
N/A
IN
IN
IN
N/A
Table 2.5: Cisco Serial Port Pinout
Pin No.
1
2
Signal Name
CTS
DCD/DSR
Input/Output
IN
IN
Chapter 2: Installation 11
Table 2.5: Cisco Serial Port Pinout (Continued)
7
8
5
6
Pin No.
3
4
Signal Name
RxD
GND
Not Used
TxD
DTR
RTS
Input/Output
IN
N/A
N/A
OUT
OUT
OUT
To connect devices, modems and PDUs to serial ports:
Make sure the crossover cable used to connect a device has the same pinout type that is configured in the software for the port (either Cyclades or Cisco).
1.
Make sure the devices to be connected are turned off.
2.
Use CAT 5 or greater crossover cables to connect the devices to the console server, using an adaptor, if necessary.
3.
To connect modems, use straight-through CAT 5 or greater cables, with an appropriate connector or adaptor (USB, DB-9 or DB-25) for the modem.
NOTE: To comply with EMC requirements, use shielded cables for all port connections.
WARNING: Do not turn on the power on the connected devices until after the console server is turned on.
Daisy chaining power devices
The following figure shows two daisy-chained Cyclades PDUs connected to serial port 2 on a console server.
12 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Figure 2.4: Example: Daisy-chained Cyclades PDUs
To daisy-chain Cyclades PDUs to the console server:
This procedure assumes that you have one Cyclades PM PDU connected to a serial port on the console server.
NOTE: Daisy chaining is not possible with SPC PDUs. ServerTech PDUs will allow only one level (Master and
Slave) of daisy chaining.
1.
Connect one end of a UTP cable with RJ-45 connectors to the OUT port of the connected
Cyclades PDU.
2.
Connect the other end of the cable to the IN port of the chained Cyclades PDU. Repeat both steps until you have connected the desired number of Cyclades PDUs.
NOTE: For performance reasons, Avocent recommends connecting no more than 128 outlets per serial port.
Turning On the Console Server
The console server is supplied with single or dual AC or DC power supplies.
WARNING: Always execute the reboot or shutdown command through the Web Manager, CLI or DSView 3 software under the Overview/Tools node before turning the console server off, then on again. This will ensure the reset doesn't occur while the file system in Flash is being accessed, and it helps avoiding Flash memory corruptions.
Chapter 2: Installation 13
To turn on an ACS with AC power:
1.
Make sure the console server is turned off.
2.
Plug the power cable into the console server and into a power source.
3.
Turn the console server on.
4.
Turn on the power switches of the connected devices.
To turn on an ACS with DC power:
DC power is connected to DC-powered console servers by way of three wires: Return (RTN),
Ground (GND) and -48 VDC.
WARNING: It is critical that the power source supports the DC power requirements of your console server. Make sure that your power source is the correct type and that your DC power cables are in good condition before proceeding. Failure to do so could result in personal injury or damage to the equipment.
The following diagram shows the connector configuration for DC power.
1 2 3 4
Figure 2.5: DC Power Connection Terminal Block
Table 2.6: DC Power Connection Details
Number
1
2
Description
Power switch
RTN (Return)
Number
3
4
Description
GND (Ground)
-48 VDC
1.
Make sure the console server is turned off.
2.
Make sure DC power cables are not connected to a power source.
3.
Remove the protective cover from the DC power block by sliding it to the left or right.
4.
Loosen all three DC power connection terminal screws.
5.
Connect your return lead to the RTN terminal, your ground lead to the GND terminal and your
-48 VDC lead to the -48 VDC terminal and tighten the screws.
14 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
6.
Slide the protective cover back into place over the DC terminal block.
7.
If your console server has dual-input DC terminals, repeat steps 3-6 for the second terminal.
8.
Connect the DC power cables to the DC power source and turn on the DC power source.
9.
Turn on the console server.
10. Turn on the power switches of the connected devices.
Configuring an ACS 6000 Console Server
An ACS 6000 console server may be configured at the appliance level through the Console menu interface accessed through the SETUP, CONSOLE or Ethernet port. All terminal commands are accessed through a terminal or PC running terminal emulation software.
NOTE: To configure using DSView 3 software, see the DSView 3 Installer/User Guide. To configure using
ACS 6000 Command Reference Guide.
To connect a terminal to the console server:
1.
Using a null modem cable, connect a terminal or a PC that is running terminal emulation software (such as HyperTerminal ® ) to the SETUP, CONSOLE or Ethernet port on the back panel of the console server. For models that support an RJ-45 port, an RJ-45 to DB9 (female) adaptor is provided.
The terminal settings are 9600 bits per second (bps), 8 bits, 1 stop bit, no parity and no flow control.
2.
Turn on each target device and then turn on the console server. When the console server completes initialization, the Console menu will display the following message: Press any key to continue.
Using Telnet/SSH
An authorized user can use a Telnet or SSH client to make a connection directly to the console of a device if all of the following are true:
The Telnet or SSH:
• protocol is enabled in the selected security profile
• protocol is configured for the port
• client is available, and it is enabled on the computer from which the connection is made
To use Telnet to connect to a device through a serial port:
For this procedure, you need the username configured to access the serial port, the port name (for example, 14-35-60-p-1), device name (for example, ttyS1), TCP port alias (for example, 7001) or
IP port alias (for example, 100.0.0.100) and the hostname of the console server or its IP address.
Chapter 2: Installation 15
To use a Telnet client, enter the information in the dialog boxes of the client.
-or-
To use Telnet in a shell, enter the following command:
# telnet [hostname | IP_address] login: username:[portname | device_name]
-or-
# telnet [hostname | IP_address] TCP_Port_Alias login: username
-or-
# telnet IP_Port_Alias login: username
To close a Telnet session:
Enter the Telnet hotkey defined for the client. The default is Ctrl ] + q to quit, or enter the text session hotkey for the CLI prompt and then enter quit .
To use SSH to connect to a device through a serial port:
For this procedure, you need the username configured to access the serial port, the port name (for example, 14-35-60-p-1), TCP port alias (for example, 7001), device name (for example, ttyS1), and the hostname of the console server, IP address or IP Port alias (for example, 100.0.0.100).
To use an SSH client, enter the information in the dialog boxes of the client.
-or-
To use SSH in a shell, enter the following command:
ssh -l username:port_name [hostname | IP_address]
-or-
ssh -l username:device_name [hostname | IP_address]
-or-
ssh -l username:TCP_Port_Alias [hostname | IP_address]
-or-
ssh -l username IP_Port_Alias
To close an SSH session:
At the beginning of a line, enter the hotkey defined for the SSH client followed by a period. The default is ~ . Or, enter the text session hotkey for the CLI prompt and then enter quit .
16 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Pluggable Devices Installation and Configuration
Before pluggable devices (PC cards and/or USB devices) can be inserted and configured, Pluggable
Device Detection must be enabled.
NOTE: Go to http://www.avocent.com to see the current list of supported pluggable devices. When a pluggable device is not in the current list of supported pluggable devices, the console server may attempt to configure the device with standard settings, allowing it to work normally.
NOTE: When a pluggable device is not listed in the internal database, the Device Info column may show no text at all or show different text based on the type of card. One example is Unknown device f024 (rev 01).
To enable Pluggable Device Detection:
1.
Select Pluggable Devices in the Web Manager.
2.
Click Enable Pluggable Device Detection.
To install and configure a pluggable device:
1.
Insert the PC card into an available slot or connect the USB device.
2.
Select Pluggable Devices in the Web Manager. The Pluggable Devices table is displayed and all detected pluggable devices are shown.
3.
Click on the pluggable device name and configure the pluggable device parameters.
NOTE: Storage devices are automatically mounted and configured. Configuration of wireless devices takes effect only after the device is ejected and re-inserted.
To eject a pluggable device:
NOTE: Always use the Web Manager to eject a pluggable device. Any other method may cause a kernel panic.
1.
Select Pluggable Devices in the Web Manager.
2.
Select the checkbox next to the pluggable device you want to eject, click Eject and remove the pluggable device.
To rename a pluggable device (available for LAN devices):
1.
Select Pluggable Devices in the Web Manager.
2.
Check the box next to the pluggable device name you want to rename, then click Rename.
3.
Enter the new name and click Save.
C H A P T E R
3
Accessing the ACS 6000 Console
Server via the Web Manager
17
Once you’ve connected your ACS 6000 console server to a network, you can access the console server via the Web Manager. The Web Manager provides direct access to the console server via a graphical user interface instead of a command-based interface.
NOTE: For instructions on accessing the console server via the CLI or DSView 3 software see the Cyclades ACS
6000 Command Reference Guide or the DSView 3 Installer/User Guide.
Web Manager Overview for Administrators
To log into the Web Manager:
1.
Open a web browser and enter the console server IP address in the address field.
2.
Log in as either admin with the password avocent or as root with the password linux .
Figure 3.1 shows a typical Web Manager screen for an administrator and descriptions follow in
Table 3.1.
18 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
1
2
3
4
Figure 3.1: Administrator Web Manager Screen
Table 3.1: Web Manager Screen Areas
2
3
Number Description
1 Top option bar. The name of the appliance and of the logged in user appear on the left side. Refresh, Print, Logout and Help buttons appear on the right.
Tab bar. Displays whether the admin is in Expert or Wizard mode.
Side Navigation Bar. Menu options for configuration, viewing of system information and access to devices. The options change based on user rights.
4 Content area. Contents change based on the options selected in the side navigation bar.
Wizard Mode
The Wizard mode is designed to simplify the setup and configuration process by guiding an administrator through the configuration steps. An administrator can configure all ports in the CAS
Profile and set the Security Profile, Network and Users Settings using the Wizard.
By default, the first time an administrator accesses the console server through the Web Manager, the Wizard will be displayed. Subsequent log-ins will open in Expert mode, and once the console server has been configured, Expert mode becomes the default mode. An administrator can toggle between Expert and Wizard modes by clicking the tab bar on the Web Manager administrator screen.
Figure 3.2 shows a typical screen when an administrator is in Wizard mode.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 19
Figure 3.2: Wizard screen
The following procedures describe how to configure the console server from the Wizard.
To configure security parameters and select a Security Profile:
1.
Select the Security link in the content area.
2.
Select the desired Security Profile. If using a Custom Security Profile, click the checkboxes and enter values as needed to configure the services, SSH and HTTP and HTTPS options to conform with your site security policy.
3.
If you are not using DSView 3 software to manage the appliance, uncheck the Allow Appliance
to be Managed by DSView box.
4.
Click Next to configure the Network or click the Network, Ports or Users link to open the appropriate screen.
To configure network parameters:
1.
Select the Network link in the content area.
2.
Enter the Hostname, Primary DNS and Domain in the appropriate fields.
3.
Select the IPv4 or IPv6 method for the ETH0 interface. If using Static, enter the Address, Mask and Gateway in the appropriate fields.
4.
Click Next to configure ports or click on the Security, Ports or Users link to open the appropriate screen.
20 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
To configure Ports:
1.
Select the Ports link in the content area.
2.
Check the box(es) to enable all ports and/or to enable Cisco RJ45 Pin-Out to change the pinout when a Cisco cable is connected.
3.
Use the appropriate drop-down menus to select the values for Speed, Parity, Data Bits, Stop
Bits, Flow Control, Protocol, Authentication Type and Data Buffering Status.
4.
Select the Data Buffering Type. If using NFS, enter the NFS Server and NFS Path information in the appropriate fields.
5.
Click Next to configure users or click on the Network, Security or Users link to open the appropriate screen.
To configure users and change the default user passwords:
WARNING: For security reasons, it is recommended you change the default password for both root and admin users immediately.
1.
Select the Users link in the content area.
2.
Click a username (admin or root) and enter the new password in the Password and Confirm
Password fields.
-or-
Click Add to add a user. Enter the new username and password in the appropriate fields.
3.
(Optional) To force the user to change the default password, select the User must change
password at next login checkbox.
4.
Assign the user to one or more groups.
5.
(Optional) Configure account expiration and password expiration.
6.
Click Next.
7.
Repeat steps 3-7 as needed to configure new user accounts and assign them to default groups.
NOTE: By default, all configured users can access all enabled ports. Additional configuration is needed if your site security policy requires you to restrict user access to ports.
8.
Click Save, then click Finish.
Expert Mode
The following tabs are available in the Side Navigation Bar of the Web Manager when an administrator is in Expert mode.
Access
Click Access to view all the devices connected to the ACS 6000 console server.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 21
To view and connect to devices using the Web Manager:
1.
Select Access in the Side Navigation Bar. The content area displays the name of the console server and a list of names or aliases for all installed and configured devices the user is authorized to access.
2.
Select Serial Viewer from the Action column. A Java applet viewer appears. In a gray area at the top of the viewer, the Connected to message shows the IP address of the console server followed by the default port number or alias.
3.
Log in if prompted.
The following table describes the available buttons in the Java applet.
Table 3.2: Java Applet Buttons for Connecting to the Console Server
Button
SendBreak
Disconnect
Purpose
To send a break to the terminal
To disconnect from the Java applet
Select the left icon to reconnect to the server or device; or select the right icon to end the session and disconnect from the Java applet
System Tools
Click System Tools to display icons which can be clicked to reboot or shut down the console server, upgrade the console server’s firmware, save or restore its configuration or open a terminal session with the console server.
System
Click System to display information about the console server and allow an administrator to configure the console server’s system parameters. The following tabs are listed under System in the
Side Navigation Bar.
Security
Security Profiles determine which network services are enabled on the console server.
During initial configuration, the console server administrator must configure security parameters to conform with the site security policy. The following security features can be configured either in the Web Manager, CLI or the DSView 3 software:
• Configure the session idle time-out
• Enable or disable RPC
• Allow all users to access enabled ports or allow the configuration of group authorizations to restrict access
22 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
• Select a Security Profile, which defines:
• Enabled services (FTP, ICMP, IPSec and Telnet)
• SSH and HTTP/HTTPS access
The administrator can select either a preconfigured Security Profile or create a custom profile.
All the services and the SSH and HTTP/HTTPS configuration options that are enabled and disabled for each Security Profile are shown in the Wizard - Security and the System - Security - Security
Profile pages.
To configure the Security Profile:
1.
Select System - Security - Security Profile.
2.
In the Idle Timeout field, enter the number of seconds before the console server times out open sessions.
NOTE: This value applies to any user session to the appliance via HTTP, HTTPS, SSH, Telnet or CONSOLE port. The new idle time-out will be applied to new sessions only.
3.
Under the Enabled Services section, enable or disable the RCP checkbox.
4.
Under the Serial Devices heading, enable or disable the Port access is controlled by
authorizations assigned to user groups checkbox.
5.
Select the checkbox for Custom, Moderate, Open or Secure under the Security Profile heading.
6.
Click Save.
You can also configure DSView 3 software security settings. When the console server is managed by the DSView 3 software, the DSView 3 server will supply the certificate to the console server.
Under normal conditions, the DSView 3 software will manage the certificate to clear and replace it with a new certificate as needed. If communication with the DSView 3 software is lost, the
DSView server will be unable to clear the certificate and the console server cannot be used. Click the Clear DSView Certificate button to configure the console server in Trust All mode.
To configure DSView 3 software security settings:
1.
Select System - Security - DSView.
2.
Click the Allow appliance to be managed by DSView checkbox and click Save.
Date and Time
The ACS 6000 console server provides two options for setting the date and time. It can retrieve the date and time from a network time protocol (NTP) server, or you can set the date and time manually so that the console server’s internal clock is used to provide time and date information.
NOTE: The Current Time displayed in the Date & Time screen shows only the time when the screen was opened. It does not continue to update in real time.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 23
To set the time and date using NTP:
1.
Click System - Date And Time.
2.
Select Enable network time protocol.
3.
Enter the NTP server site of your choice and click Save.
To set the time and date manually:
1.
Click System - Date And Time.
2.
Select Set manually.
3.
Using the drop-down menus, select the required date and time and click Save.
To set the time zone using a predefined time zone:
1.
Click System - Date And Time - Time Zone.
2.
Select Predefined.
3.
Select the required time zone from the drop-down menu and click Save.
To define custom time zone settings:
1.
Click System- Date And Time - Time Zone.
2.
Select Define Time Zone.
3.
Enter the Time Zone Name and Standard Time Acronym of your choice.
4.
Enter the GMT Offset.
5.
Select Enable daylight savings time if needed.
6.
Select or enter the required values for daylight savings time settings and click Save.
Help and Language
Click System - Help And Language and use the drop-down menu to select the console server’s language. Enter the full URL of the online help, ending in /index.html, on the local web server in the Online Help URL field. Click Save.
Online help
When the online help feature is configured for your console server, clicking the Help button from any form on the Web Manager opens a new window and redirects its content to the configured path for the online help product documentation.
NOTE: Using the online help feature from the Avocent/Cyclades server is not always possible due to firewall configurations, nor is it recommended. It is generally advisable for you to use the online help system provided with the product or download the online help .zip file and run it from a local server.
The system administrator can download the online help from Avocent. For more information on downloading the online help, contact Technical Support.
24 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Once the online help file is obtained (in zip format), the files must be extracted and put in to a userselected directory under the web server’s root directory. The web server must be publicly accessible.
NOTE: The default URL for online help is http://global.avocent.com/us/olh/acs6000/v_2.0.0/en/index.html.
Boot Configuration
Boot configuration defines the location from which the console server loads the operating system.
The console server can boot from its internal firmware or from the network. By default, the console server boots from Flash memory. Clicking System- Boot Configuration will display the Boot
Configuration screen.
If you need to boot from the network, make sure the following prerequisites are met:
• A TFTP or BootP server must be available on the network
• An upgraded console server boot image file must be downloaded from Avocent and made available on the TFTP or BootP server
• The console server must be configured with a fixed IP address
• The boot filename and the IP address of the TFTP or BootP server is known
To configure boot configuration:
1.
Click System - Boot Configuration.
2.
Under Boot Mode, select From Flash, and select Image 1 or Image 2.
-or-
Select From Network and enter the following information:
• Appliance IP Address: Enter the fixed IP address or a DHCP assigned IP address to the console server.
• TFTP Server IP: Enter the IP address of the TFTP boot server.
• Filename: Enter the filename of the boot firmware.
3.
Using the drop-down menu, select whether the Watchdog Timer is enabled. If the Watchdog
Timer is enabled, the console server reboots if the software crashes.
4.
Using the drop-down menu, select one of the following speeds for both Ethernet 0 Mode and
Ethernet 1 Mode: 100BT full, 100BT half, 10BT full, 10BT half or Auto.
5.
Using the drop-down menu, select the console port speed and click Save.
NOTE: Ethernet Mode will be affected after saving. The rest of the configuration will be applied after rebooting.
Information
Click System-Information to view the console server’s identity, versions, power and CPU information.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 25
Usage
Click System-Usage to view memory and Flash usage.
Network
Click Network to view and configure the network options for Hostname, DNS, IPv6, Bonding, IPv4 and IPv6 static routes, Hosts, Firewall, IPSec (VPN) and SNMP.
Settings
Click Network - Settings to make changes to the configured network settings.
Devices
An administrator can select, enable and configure the IP addresses assigned to the network interfaces and view the MAC address. Besides the two standard Ethernet interfaces, the list of network interfaces includes entries for any Ethernet PC cards that may be installed.
To configure a network device:
1.
Select Network - Devices. The Devices screen appears with a list of network interfaces and their status (enabled or disabled).
2.
Click the name of the network device to configure.
3.
Select the status (either Enabled or Disabled) from the drop-down menu.
4.
Select one of the following IPv4 method options:
• Select DHCP to have the IPv4 IP address set by the DHCP server.
• Select Static to enter the IPv4 IP address and subnet mask manually.
• Select IPv4 address unconfigured to disable IPv4.
5.
Select one of the following IPv6 method options:
• Select Stateless if the link is restricted to the local IP address.
• Select DHCPv6 to have the IPv6 IP address set by the DHCP server.
• Select Static to enter the IPv6 IP address and prefix length manually.
• Select IPv6 address unconfigured to disable IPv6.
6.
Select the Ethernet Mode for the built-in interface (ETH0 and ETH1).
NOTE: The MAC Address for the device will be displayed after this option.
NOTE: The following step is only active for mounted Ethernet PC cards.
7.
Enter the following Wireless LAN information: a.
Select MyPrivateNet (ESSID) to enter the unique identifier for the wireless access point.
b.
Select Channel to enter the communication channel with the access point.
c.
Select Encrypted to enable data encryption during transmission.
26 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide d.
Enter the key or password to decode incoming encrypted data, then click Save.
IPv4 and IPv6 static routes
To add static routes:
1.
Select Network - IPv4 Static Routes or IPv6 Static Routes. Any existing static routes are listed with their Destination IP/Mask, Gateway, Interface and Metric values shown.
2.
Click Add.
3.
Select Default to configure the default route.
-or-
Select Host IP Or Network to enter custom settings for Destination IP/Mask.
Enter the required Destination IP/Mask Bits with the syntax <destination IP>/<CIDR> in the
Destination IP/Mask Bits field.
4.
Enter the IP address of the gateway in the Gateway field.
5.
Enter the number of hops to the destination in the Metric field, then click Save
Hosts
An administrator can configure a table of host names, IP addresses and host aliases for the local network.
To add a host:
1.
Select Network - Hosts.
2.
Click Add to add a new host.
3.
Enter the IP address, hostname and alias of the host you want to add, then click Save.
To edit a host:
1.
Select Network - Hosts.
2.
Click on the IP address of the hostname you want to edit.
3.
Enter a new hostname and alias, as applicable, then click Save.
Firewall
Administrators can configure the ACS 6000 console server to act as a firewall. By default, three built-in chains accept all INPUT, FORWARD and OUTPUT packets. Select the Add, Delete or
Change Policy buttons to add a user chain, delete user added chains and to change the built-in chains policy. Default chains can have their policy changed (Change Policy) to accept or drop, but cannot be deleted. Clicking on the Chain Name allows you to configure rules for chains.
Firewall configuration is available by clicking on Network - Firewall. Separate but identical configuration screens are available from either the IPv4 Filter Table or IPv6 Filter Table menu options.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 27
Only the policy can be edited for a default chain; default chain policy options are ACCEPT and
DROP.
When a chain is added, only a named entry for the chain is created. One or more rules must be configured for a chain after it is added.
Configuring the firewall
For each rule, an action (either ACCEPT, DROP, RETURN, LOG or REJECT ) must be selected from the Target pull-down menu. The selected action is performed on an IP packet that matches all the criteria specified in the rule.
If LOG is selected from the Target pull-down menu, the administrator can configure a Log Level, a
Log Prefix and whether the TCP sequence, TCP options and IP options are logged in the Log
Options Section.
If REJECT is selected from the Target pull-down menu, the administrator can select an option from the Reject with pull-down menu; the packet is dropped and a reply packet of the selected type is sent.
Protocol options
Different fields are activated for each option in the Protocol pull-down menu.
If Numeric is selected from the Protocol menu, enter a Protocol Number in the text field.
If TCP is selected from the Protocol menu, a TCP Options Section is activated for entering source and destination ports and TCP flags.
If UDP is selected from the Protocol menu, the UDP section is activated for entering source and destination ports.
Table 3.3: Firewall Configuration - TCP and UDP Options Fields
Field/Menu Option Definition
A single IP address or a range of IP addresses. Source Port
- or -
Destination Port
TCP Flags [TCP only] SYN (synchronize), ACK (acknowledge), FIN (finish), RST (reset),
URG (urgent) and PSH (push). The conditions in the pull-down menu for each flag are: Any, Set or Unset.
If ICMP is selected from the Protocol menu, the ICMP Type pull-down menu is activated.
If an administrator enters the Ethernet interface (eth0 or eth1) in the input or output interface fields and selects an option (2nd and further packets, All packets and fragments or Unfragmented packets
and 1st packets) from the Fragments pull-down menu, the target action is performed on packets from or to the specified interface if they meet the criteria in the selected Fragments menu option.
28 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
To add a chain:
1.
Select Network - Firewall.
2.
Select either IPv4 Filter Table or IPv6 Filter Table as needed.
3.
Click Add.
4.
Enter the name of the chain to be added.
5.
Click Save.
NOTE: Spaces are not allowed in the chain name.
6.
Add one or more rules to complete the chain configuration.
To change the policy for a default chain:
NOTE: User-defined chains cannot be edited. To rename a user-added chain, delete it and create a new one.
1.
Select Network - Firewall.
2.
Select either IPv4 Filter Table or IPv6 Filter Table as needed.
3.
Select the checkbox next to the name of the chain you want to change (FORWARD, INPUT,
OUTPUT).
4.
Click Change Policy and select Accept or Drop from the drop-down menu.
5.
Click Save.
To add a rule:
1.
Select Network - Firewall.
2.
Select either IPv4 Filter Table or IPv6 Filter Table as needed.
3.
From the chain list, click the name of the chain you want to add a rule to.
4.
Click Add and configure the rule as needed, then click Save.
To edit a rule:
1.
Select Network - Firewall.
2.
Select either IPv4 Filter Table or IPv6 Filter Table as needed.
3.
From the chain list, click the name of the chain with the rule you want to edit.
4.
Select the rule you want to edit and click Edit.
5.
Modify the rule as needed and click Save.
IPSec(VPN)
Virtual Private Network (VPN) enables a secure communication between the console server and a remote network by utilizing a gateway and creating a secured connection between the console server and the gateway. The IPSec protocol is used to construct the secure tunnel and provides encryption and authentication services at the IP level of the protocol stack.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 29
NOTE: IPSec(VPN) is not supported with IPv6.
When Network - IPSec(VPN) is selected, the IPSec(VPN) screen is displayed.
Use the Add button to add a VPN connection or click on an existing connection name to edit one already in the list. Click the Delete button to delete an existing connection. If NAT settings need to be changed, click the Configure NAT button.
When you click the Add button, the IPSec(VPN) - Add screen is displayed.
The remote gateway is referred to as the remote or right host and the console server is referred to as the local or left host. If left and right are not directly connected, then you must also specify a
NextHop IP address.
The next hop for the remote or right host is the IP address of the router to which the remote host or gateway running IPSec sends packets when delivering them to the left host. The next hop for the left host is the IP address of the router to which the console server sends packets to for delivery to the right host.
A Fully Qualified Domain Name should be indicated in the ID fields for both the Local (Left) host and the Remote (Right) host where the IPSec negotiation takes place.
The following table describes the fields and options on the IPSec(VPN) - Add screen. The information must match exactly on both ends for local and remote.
Table 3.4: Field and Menu Options for Configuring IPSec(VPN)
Field Name
Connection Name
Authentication Protocol
Boot Action
Authentication Method
Definition
Any descriptive name you wish to use to identify this connection.
The authentication protocol used, either ESP (Encapsulating Security
Payload) or AH (Authentication Header).
The boot action configured for the host, either Ignore, Add or Start.
Authentication method used, either RSA Public Keys or Shared Secret.
30 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Table 3.4: Field and Menu Options for Configuring IPSec(VPN) (Continued)
Field Name
Remote (Right) Side
- and -
Local (Left) Side
Definition
Enter the required address or text for each of the four fields for both
Remote Side and Local Side:
ID: This is the hostname that a local system and a remote system use for
IPSec negotiation and authentication. It can be a fully qualified domain name preceded by @. For example, [email protected]
IP Address: The IP address of the host.
NextHop: The router through which the console server (on the left side) or the remote host (on the right side) sends packets to the host on the other side.
SubNet: The netmask of the subnetwork where the host resides.
Use CIDR notation. The IP number followed by a slash and the number of
‘one’ bits in the binary notation of the netmask. For example, 192.168.0.0/
24 indicates an IP address where the first 24 bits are used as the network address. This is the same as 255.255.255.0.
RSA Key (If RSA Key is selected) For IPSec(VPN) authentication, you need to generate a public key for the console server and find out the key used on the remote gateway. Copy and paste for copying the RSA key from another source is supported.
Pre-Shared Secret (If Secret is selected)
Pre-shared password between left and right users.
SNMP Configuration
An administrator can configure SNMP, which is needed if notifications are to be sent to an SNMP management application.
NOTE: The Avocent ACS 6000 Enterprise MIB text file is available in the appliance at: /usr/local/mibs/ACS6000-
MIB.asn. The Avocent ACS 6000 Enterprise TRAP MIB text file is available in the appliance at: /usr/local/mibs/
ACS6000-TRAP-MIB.asn. Both files are also available at www.avocent.com.
To configure SNMP:
1.
Click Network - SNMP.
2.
Click the System button.
a.
Enter the SysContact information (email address of the console server’s administrator, for example, [email protected]
).
b.
Enter the SysLocation information (physical location of the console server, for example,
Cyclades_ACS6000 ), then click Save to go back to the SNMP screen.
3.
Click Add to add a new community or v3 user.
4.
Enter the community name for SNMP v1/v2 or the user name for SNMP v3 in the Name field and enter the OID.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 31
5.
Select the desired permission from the pull-down menu. Choices are Read and Write or Read
Only.
6.
If the required SNMP version is v1 or v2, click the Version v1, v2 button, then enter the source
(valid entry is the subnet address).
-or-
If the required SNMP version is v1 or v2 using an IPv6 network, click the Version v1,v2 for
IPv6 network button, then enter the source (valid entry is the subnet address).
-or-
If the required SNMP version is v3, click the Version v3 button, then select the Authentication
Type (MD5 or SHA), enter the authentication passphrase or password, enter the privacy passphrase for DES and select the Minimum Authentication Level (NoAuthNoPriv,
AuthNoPriv, AuthPriv).
7.
Click Save.
Ports
An administrator can enable and configure serial ports, auxiliary ports, the CAS Profile and the
Dial-in Profile from the Ports tab in the Side Navigation Bar. On the auxiliary ports screen, you can enable the auxiliary port and configure it based on the type of connected device.
Serial ports
On the Serial Ports table, you can specify the connection profile (CAS, Dial-In or Power) based on the type of connected device and you can clone the port, reset to factory defaults and enable/disable ports.
To enable or disable one or more serial ports:
1.
Select Ports - Serial Ports.
2.
Click the checkbox for each port you want to enable or disable.
3.
Click the Enabled or Disabled button.
To configure or edit one or more serial ports with the CAS Profile:
1.
Select Ports - Serial Ports.
2.
Click the checkbox for each port you want to configure.
3.
Click the Set CAS button.
a.
To change the default pinout when a Cisco cable is connected to the selected port(s), select the Enable Cisco from the RJ-45 pinout checkbox. b.
Use the drop-down menus to enable or disable the port and set the speed, parity, data bits, stop bits and flow control.
4.
Click Next or click the CAS link.
32 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide a.
Enter the port name (when only one port was selected) or the port name prefix (when more than one port were selected). The port name will be <port name prefix>-p-<port number>.
b.
Check the box to enable auto discovery. In this case, the port name will be used when auto discovery fails to discover the server name. Check the box to enable speed auto detection.
NOTE: Auto speed detection requires additional configuration in the CAS Profile-Auto Discovery Settings screen. c.
Use the appropriate drop-down menus to set the protocol and authentication type.
d.
Enter the text session hotkey and power session hotkey in the appropriate fields. e.
Enter the TCP port alias in the appropriate field. f.
Enter the IPv4 or IPv6 alias and its interface in the appropriate field. g.
To allow a session only if DCD is on and to enable auto answer, check the appropriate boxes. h.
Use the drop-down menu to select the DTR mode and enter the DTR off interval.
i.
Use the drop-down menus to enable or disable line feed suppression and NULL after CR suppression.
j.
Enter the transmission interval, break sequence and break interval in the appropriate fields.
k.
Use the drop-down menus to enable or disable log in/out multisession notification and informational message notification.
5.
Click Next or click the Data Buffering link and use the drop-down menus to enable and configure data buffering.
6.
Click Next or click the Alerts link.
a.
Click Enable Alerts to enable detection of alerts.
b.
Click Add to add an alert string. Enter the string in the Alerts String field and click Next to return to the Alerts screen. c.
Check the box next to an existing alert and click Delete to delete the string.
d.
Click Delete Any to delete all strings whether selected or not.
NOTE: Clicking Delete Any will delete all alert strings. Selecting all the alert strings and clicking Delete is not the same functon as it will not delete alert strings not shown in the table.
7.
Click Next or click the Power link.
a.
Click Add to add a new outlet. Click Selected PDU and select a PDU from the list of detected PDUs. Enter the outlet(s) in the Outlets field, and click Next. b.
Check the box next to an existing merged outlet and click Delete to delete it.
NOTE: Power is only available when a single serial port is selected.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 33
8.
Click Save.
Table 3.5: CAS Profile Parameters
Parameter
Physical
Enable Cisco RJ-45
Pin-Out
Status
Description
Defines the serial port pinout. Default setting: Disabled.
Speed
Parity
Data Bits
Stop Bits
Flow Control
Protocol
Authentication Type
Defines the status of the serial port as either enabled or disabled.
Default: Disabled.
Defines the speed as 300, 1200, 2400, 4800, 9600, 19200, 38400,
57600 or 115200. Default: 9600.
Defines the parity as either Even, Odd or None. Default: None.
Defines the data bits as either 5, 6, 7 or 8. Default: 8.
Defines the stop bits as either 1 or 2. Default: 1.
Defines the flow control as none, hardware, software, RxON software or TxON software. Default: None.
CAS
Port Name Name associated with the serial port (as an alias). Default: <appliance mac address>-p-<port number>.
Enable Auto Discovery The target name will be discovered and will be associated with this serial port. If it fails, the Port Name will be used. Default: Disabled.
Enable Speed Auto
Detection
Tries to discover the speed of the serial port. This feature requires additional configuration under the CAS Profile / Auto Discovery /
Settings page. Default: Disabled.
The protocol that will be used to access the serial port/target.
• SSH - SSH session.
• Telnet - Telnet session.
• SSH/Telnet - allow SSH session and/or Telnet session.
Default: SSH/Telnet.
Authentication type that will be used to authenticate the user during target session. Default: Local.
Text Session Hot Key Hotkey to suspend the target session and go to the CLI prompt.
Default: ^Z ( Ctrl-Z ).
Power Session Hot Key Hotkey to suspend the target session and display Power Management
Menu to control the outlets merged to the target. Default: ^P ( Ctrl-P) .
34 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Table 3.5: CAS Profile Parameters (Continued)
Parameter
TCP Port Alias
Port IPv4/IPv6 Alias
Description
For a Telnet session: TCP port to connect directly to a serial port.
For SSH session: Alias of the port similar to ttySxx. Default: 70XX, where XX is the serial port number.
IPv4/IPv6 address used to connect directly to a serial port. Default: not configured (empty).
Interface (ETH0/ETH1) associated with the IPv4/IPv6 alias. Default:
ETH0.
Port IPv4/IPv6 Alias
Interface
Allow Session Only if
DCD is On
Enable Auto Answer
When the DCD is OFF, the appliance will deny access for this serial port. Default: Disabled (allow access if DCD is OFF).
When the input data matches one input string configured in Auto
Answer, the output string will be transmitted to the serial port. Default:
Disabled.
DTR Mode DTR Mode can be set to the following:
• Always On.
• Normal - the DTR status will depend on the existence of a CAS session.
• Off Interval - when the a CAS session is closed, the DTR will stay down during this interval.
Default: Normal.
DTR Off Interval Interval in seconds used by DTR Mode Off Interval in milliseconds.
Default: 100.
Line Feed Suppression Enables the suppression of the LF character after the CR character.
Default: Disabled.
Null After CR
Suppression
Transmission Interval
Enables the suppression of the NULL character after the CR character. Default: Disabled.
The interval the port waits to send data to a remote client in milliseconds. Default: 20.
Break Sequence Sequence used to send a break signal to the serial port. Default:
~break.
Interval for the break signal in milliseconds. Default: 500.
Break Interval
Log In/Out Multi
Session Notification
Enables the notification to multi-session users when a new user logs in or a user logs out. Default: Disabled.
Informational Message
Notification
Displays an information message when a target session is opened.
Default: enabled.
Data Buffering
Status Enables or disables data buffering. Default: Disabled.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 35
Table 3.5: CAS Profile Parameters (Continued)
Parameter
Type
Description
Displays the type of data buffering:
• Local - stores the data buffering file in the local file system.
• NFS - stores the data buffering file in the NFS server.
• Syslog - sends the data to the syslog server.
• DSView - sends the data to the DSView 3 software.
Default: Local.
Time Stamp
Log-in/out Message
When enabled, adds the time stamp to the data buffering line for a
Local or NFS database. Default: Disabled.
Includes special notification for logins and logouts in data buffering.
Default: Disabled.
Serial Session Logging • Enabled - stores data at all times.
• Disabled - stores data when a CAS session is not opened.
Default: Enabled.
Alerts
Status
Alert Strings
A special event notification will be generated when input data matches one of the alert strings. Default: Disabled.
Strings used to generate event notifications. Default: Empty.
To configure the Dial-in Profile for a serial port with a connected modem:
1.
Select Ports - Serial Ports.
2.
Click the checkbox for a serial port with a connected modem.
3.
Click the Set Dial button and use the drop-down menus to configure the dial-in settings.
4.
Configure the PPP parameters (address, authentication and so on) and click Save.
Table 3.6: Dial-in Parameters
Parameter
Status
Speed
Init Chat
PPP Address
Description
Enables or disables the port. Default: Disabled.
The speed that will be used by mgetty to configure the serial device.
Default: 38400 bps.
Chat for modem initialization. Default: "" \d\d\d+++\d\d\dATZ OK.
Configures the local and the remote IP address for the the PPP link. If
Accept Configuration from Remote Peer is selected, the remote peer should send both IP addresses (local and remote) during negotiation.
Default: No Address.
36 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Table 3.6: Dial-in Parameters (Continued)
Parameter
Local IPv4/IPv6
Address
Remote IPv4/IPv6
Address
PPP Authentication
Protocol
Description
Configures the local IPv4/IPv6 address for this PPP connection.
Configures the remote IPv4/IPv6 address for this PPP connection.
CHAP
PPP Idle Timeout
Uses the radio button to select: none, PAP, CHAP or EAP.
• None - no authentication.
• PAP - use PAP protocol and the authentication type configured in the PPP authentication type (it is configured in the Authentication /
Unit Authentication page).
• CHAP - use CHAP protocol. The configuration of the CHAP secrets should be done while editing the file /etc/ppp/chap-secrets.
• EAP - use EAP protocol. Available authentications: CHAP, SRP-
SHA1 and TLS. The configuration of the secrets for CHAP should be done while editing the file /etc/ppp/chap-secrets. The configuration of the secrets for SRP-SHA1 should be done while editing the file /etc/ppp/srp-secrets.
Default: None.
Configure the CHAP-interval, CHAP-max-challenge and CHAPrestart.
Default values:
CHAP Interval = 0.
CHAP Max Challenge = 10.
CHAP Restart = 3.
Number of seconds being idle before PPP times out. Default: 0 (no time-out).
To configure or to edit one or more serial ports with a connected PDU:
1.
Select Ports - Serial Ports.
2.
Click the checkbox for one or more serial ports with a connected PDU.
3.
Click the Set Power button and use the drop-down menus to configure the physical settings.
4.
Click Next or click the Power link.
a.
Use the drop-down menu to select the PDU type.
b.
Check the box to enable speed auto detection. c.
Configure the polling rate.
d.
For Avocent/Cyclades PDUs, enter the power cycle interval and then use the drop-down menus to enable or disable Syslog, Buzzer and SW Overcurrent Protection.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 37
5.
Click Save.
Table 3.7: Power Parameters
Parameter
Physical
Enable Cisco RJ-45
Pin-Out
Status
Description
Defines the serial port pinout. Default setting: Disabled.
Speed
Parity
Data Bits
Stop Bits
Flow Control
Defines the status of the serial port as either enabled or disabled.
Default: Disabled.
Defines the speed as 300, 1200, 2400, 4800, 9600, 19200, 38400,
57600 or 115200. Default: 9600.
Defines the parity as either Even, Odd or None. Default: None.
Defines the data bits as either 5, 6, 7 or 8. Default: 8.
Defines the stop bits as either 1 or 2. Default: 1.
Defines the flow control as none, hardware, software, RxON software or TxON sofware. Default: None.
Power
PDU Type Defines the type or vendor of the PDU connected to the serial port.
• Auto - the vendor will be detected.
• Avocent-Cyclades - Avocent-Cyclades PM PDU family.
• SPC - SPC power control device family.
• Server Tech - Server Tech family.
Default: Auto.
When enabled, detects the speed of the port. Default: Disabled.
Enable Speed Auto
Detection
Pooling Rate
For Avocent/Cyclades
PDUs
Power Cycle Interval The interval in seconds between Off and On actions for the power cycle command. Default: 15.
Syslog
The interval in seconds to update information from the PDU. Default:
20.
When enabled, the PDU will send syslog messages to the appliance.
Default: Enabled.
Enables or disables the PDU’s buzzer. Default: Enabled.
Buzzer
SW Overcurrent
Protection
When enabled, the software’s overcurrent protection is on. Default:
Disabled.
38 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
To copy/clone the configuration of one port to other ports:
1.
Select Ports - Serial Ports.
2.
Click the checkbox for the serial port you want to clone.
3.
Click the Clone button.
4.
Enter the serial port(s) to be configured in the Copy Configuration To field and click Save.
NOTE: If the selected port is configured as a CAS Profile, the following parameters will not be copied: Port
Name, TCP Port Alias, IPv4 Port Alias, IPv6 Port Alias and Power (merged outlets).
To reset one or more serial ports to their factory configuration:
1.
Select Ports - Serial Ports.
2.
Click the checkbox for one or more serial ports you want to reset to their factory configuration, then click the Reset To Factory button.
NOTE: Serial ports are set to the CAS Profile and disabled in the factory configuration.
Auxiliary ports
On the Auxiliary Ports screen, you can enable the auxiliary port and configure it based on the type of connected device.
To configure an appliance with an internal modem:
1.
Select Ports - Auxiliary Ports.
2.
Use the drop-down menus to configure the Dial-in settings.
3.
Configure the PPP parameters (address, authentication, and so on) and click Save.
To configure or edit auxiliary port with connected PDU:
1.
Select Ports - Auxiliary Ports.
2.
Click the Set Power button and use the drop-down menus to configure the physical settings.
3.
Click Next or click the Power link.
a.
Use the drop-down menu to select the PDU type.
b.
Check the box to enable speed auto detection. c.
Configure the polling rate.
d.
For Avocent/Cyclades PDUs, enter the power cycle interval and then use the drop-down menus to enable or disable Syslog, Buzzer and SW Overcurrent Protection.
4.
Click Save.
To configure or edit auxiliary port with a connected modem:
1.
Select Ports - Auxiliary Ports.
2.
Click the Set Dial-In button and use the drop-down menus to configure the Dial-in settings.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 39
3.
Configure the PPP parameters (address, authentication, and so on).
4.
Click Save.
CAS Profile
An administrator can configure settings for auto discovery and for auto answer features.
Auto discovery
The auto discovery feature will discover the target name of the server connected to the serial port.
This name will be used as the alias of the serial port.
When auto discovery is active for a certain serial device, upon target connection (DCD ON event), the appliance will send probe strings and start analyzing target device answers using regular expressions. There will be predefined probe and match strings as well as customer-defined ones.
For each probe string sent, all regular expressions defined by the match strings will be tested. After the last cycle, the sequence restarts. This procedure will run for a certain period (given by the auto discovery time-out parameter) or until the target is successfully detected. If auto discovery fails, the target name will be reset to the corresponding unique default target name.
The probe strings will be used to stimulate the server (such as “\n”: a single newline).
The match strings are regular expressions where “%H” is a placeholder for the target name you want to detect, such as:
“ \\(.*\\)(%H)\\(.*\\)” or just “xxx%Hyyy”.
The first one will extract target name from things such as: nanana(myTarget): à results: myTarget jhdsgjhas(tg2)kjafja à results: tg2
But would match for: hsagdfjhagfxxxTARGETyyyyyy à resulting: TARGET
To configure the strings for probe/match used by auto discovery:
Perform this procedure to change the default settings or the probe or match strings used in auto discovery.
1.
Select Ports - CAS Profile - Auto Discovery. The Settings, Probe Strings and Match Strings options appear in the Side Navigation Bar.
2.
To change the default auto discovery time-out or probe time-out, perform the following steps.
a.
Select Settings.
b.
Enter a new value in the Auto Discovery Timeout and Probe Timeout fields.
c.
Select a speed from the Default Speed on Auto Discovery Failure drop-down menu and
Probe Speed List.
d.
Click Save.
40 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
3.
To add a new probe or match string or delete an existing string, perform the following steps.
a.
Select Probe Strings or Match Strings. b.
To add a string, click Add, enter a new string in the New Probe String or New Match
String field and click Save.
c.
To delete a string, select the checkbox for the string and click Delete.
4.
Click Save.
To configure the input/output strings used by auto answer:
1.
Select Ports - CAS Profile - Auto Answer.
2.
To add an auto answer input and output string, click Add. Enter a new string in the Input String or Output String fields and click Save.
-or-
To delete an auto input and output string, select the checkbox next to the string you want to delete. Click Delete, then click Save.
Dial-in Profile
An administrator can configure secure dial-in settings such as OTP login, PPP connections, PPP/
PAP authentication, callback and OTP users for PPP connections.
NOTE: If pluggable devices are being used for dial-out, dial-in should be disabled.
To configure secure dial-in settings for ports with the Dial-in Profile:
1.
Select Ports - Dial-In Profile - Settings.
2.
To enable logging in to the console server through the modem and select a condition for which logging in is allowed, perform the following steps.
a.
To allow callback connections only, select Callback.
b.
To allow any connection, select Enable.
3.
To enable OTP authentication, select Enable from the OTP Login Authentication menu.
4.
To enable and select a condition for PPP connections, perform the following steps.
a.
To allow PPP callback connections only, select Callback.
b.
To allow any connection, select Enable.
5.
When the PAP authentication protocol is configured for the port, select the authentication type from the PPP/PAP Authentication menu.
6.
Click Save.
To configure callback users and phone numbers for ports with the Dial-in Profile:
1.
Select Ports - Dial-In Profile - Secure Dial-In - Callback Users.
2.
Click Add.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 41
3.
Enter the name and phone number used to perform the callback in the appropriate fields and click Save.
To configure PPP OTP users for ports with the Dial-in Profile:
1.
Select Ports - Dial-In Profile - Secure Dial-In - PPP OTP Users.
2.
Click Add.
3.
Enter the username and passphrase in the appropriate fields and click Save.
NOTE: This PPP OPT user will establish PPP connection after being successfully authenticated.
To configure EAP-TLS as PPP authentication for ports with the Dial-in Profile:
1.
Select Ports - Serial Ports.
-or-
Select Ports - Auxiliary Ports.
2.
Check the box next to the port where the modem is connected and click Set Dial-In.
NOTE: If using an auxiliary port, the modem can be internal.
3.
Configure the PPP Address settings. For example, set the PPP Address to Local Configuration using 10.0.0.1 as the Local IPv4 Address and 10.0.0.2 as the Remote IPv4 Address.
4.
For PPP Authenticaion, select the button next to By Appliance, and then select the button next to EAP for the protocol. Click Save.
5.
Select Ports - Dial-In Profile - Settings.
6.
Use the drop-down menu to enable the PPP Connection and click Save.
7.
Copy the certificates and keys to /etc/ppp/cert. They must be named server.crs (the ACS 6000 console server certificate), ca.crt (the Certificate Authority’s certificate), server.key (the ACS
6000 console server asymmetric key).
Pluggable Devices
To manage pluggable devices:
1.
If Pluggable Device Detection is enabled, select Pluggable Devices.
-or-
If it is disabled, click Enable Pluggable Device Detection.
2.
Select the checkbox next to the pluggable device you wish to configure, or select the checkbox above the list of pluggable devices to select them all.
3.
Click Insert All, Eject or Rename.
4.
To disable detection, click Disable Pluggable Devices Detection.
42 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
To view and change pluggable device information:
1.
Select Pluggable Devices and select a pluggable device name.
2.
If the pluggable device type is Network, the Network/Device section will be visible to allow the configuration of the network parameters.
-or-
If the pluggable device type is Modem (V.92 or wireless), the dial-in section will be visible to allow the configuration of the dial-in parameters.
Authentication
Authentication can be performed locally, with OTP, or on a remote Kerberos, LDAP, NIS, Radius or TACACS+ authentication server. If the ACS 6000 console server is managed by a DSView 3 server, DSView authentication is also supported. The console server also supports remote group authorizations for the LDAP, Radius and TACACS+ authentication methods.
Fallback mechanisms of the following types are available:
Local authentication can be tried first, followed by remote, if the local authentication fails (Local/
Remote_Method)
-or-
Remote authentication may be tried first, followed by local (Remote_Method/Local)
-or-
Local authentication may be tried only if a remote authentication server is down
(Remote_Method_Down_Local).
An administrator can configure authentication using the CLI utility and the Web Manager. The default authentication method for the console server and the serial ports is Local. Any authentication method that is configured for the console server or the ports is used for authentication of any user who attempts to log in through Telnet, SSH or the Web Manager.
Appliance authentication
The ACS 6000 console server authenticates for the console server and the ports, either in groups or individually.
NOTE: It is advised when using group authorization that you use the same authorization for both the console server and all serial ports, or use Single Sign-on Authentication to facilitate group authorization.
When Single Sign-on Authentication is disabled, the console server uses the individual port configurations. Users must use their password each time they access an individual port. If enabled,
Single Sign-on Authentication will use the authentication server you choose from the pull-down menu for all ports and no further authentication will be needed when accessing the port after that.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 43
NOTE: Selecting unconfigured from the pull-down menu will allow the ports to continue to use individual authentication servers, and will require your password the first time you access any port. After that, the port will not require password authentication if Single Sign-on Authentication is enabled.
To set authentication for the console server:
1.
Click Authentication - Appliance Authentication.
2.
Select the desired authentication server from the Authentication Type drop-down menu.
3.
Select Enable single sign-on to enable single sign-on authentication, and select the desired authentication server from the Authentication Type drop-down menu.
4.
Click Save.
Authentication servers
When using an authentication server, you must configure its IP address and in most cases other parameters before it can be used. The following authentication servers require configuration:
RADIUS, TACACS+, LDAP(S)|AD, Kerberos, NIS and DSView 3 servers.
To configure a RADIUS authentication server:
1.
Select Authentication - Authentication Servers - RADIUS.
2.
Enter the IP addresses of the First Authentication Server and First Accounting Server.
3.
If used, enter the IP addresses for the Second Authentication Server and Second Accounting
Server.
4.
Enter your secret word or passphrase in the Secret field (applies to both first and second authentication and accounting servers), then re-enter the secret word or passphrase in the
Confirm Secret field.
5.
Enter the desired number of seconds for server time-out in the Timeout field.
6.
Enter the desired number of retries in the Retries field.
7.
If you select the Enable Service-Type attribute to specify the authorization group checkbox, enter the authorization group name for each of the following Service Types: Login, Framed,
Callback Login, Callback Framed, Outbound and Administrative.
8.
Click Save.
To configure a TACACS+ authentication server:
1.
Select Authentication - Authentication Servers - TACACS+.
2.
Enter the IP addresses for the First Authentication Server and First Accounting Server.
3.
If used, enter the IP addresses of the Second Authentication Server and Second Accounting
Server.
4.
Select the desired service (PPP or raccess) from the Service drop-down menu.
44 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
5.
Enter your secret word or passphrase in the Secret field (applies to both first and second authentication and accounting servers), then re-enter the secret word or passphrase in the
Confirm Secret field.
6.
Enter the desired number of seconds for server time-out in the Timeout field.
7.
Enter the desired number of retries in the Retries field.
8.
If you select the Enable User-Level attribute to specify the authorization group checkbox, enter the authorization group name for up to 15 User-Levels.
9.
Click Save.
To configure an LDAP(S)|AD authentication server:
1.
Select Authentication - Authentication Servers - LDAP(S)|AD.
2.
Enter the IP address of the server.
3.
Enter the Base.
4.
At the Secure drop-down menu, select Off, On or Start_TLS.
5.
Enter the Database User Name.
6.
Enter your Database Password, then re-type the database password in the Confirm Password field.
7.
Enter your desired Login Attributes.
8.
Click Save.
To configure a Kerberos authentication server:
1.
Select Authentication - Authentication Servers - Kerberos.
2.
Enter the IP address (Realm) of the server.
3.
Enter the Realm Domain Name (example: avocent.com
).
4.
Enter the Domain Name (example: avocent.com
).
5.
Click Save.
To configure an NIS authentication server:
1.
Select Authentication - Authentication Servers - NIS.
2.
Enter the NIS Domain Name of the server (example: corp.avocent.com
).
3.
Enter the NIS Server Address or broadcast (default is broadcast).
4.
Click Save.
To configure a DSView authentication server:
1.
Select Authentication - Authentication Servers - DSView.
2.
Enter IP Address 1 - 4 for the DSView servers in the relevant fields.
3.
Click Save.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 45
Users Accounts and User Groups
Access to ports can be optionally restricted, based on authorizations that an administrator can assign to custom user groups. Groups can also be authorized to manage power while connected to devices. The ACS 6000 console server has two default users (admin and root) and four pre-defined user groups: admin, appliance-admin, shell-login-profile and user.
A user account must be defined for each user on the console server or on an authentication server.
The admin and root users have accounts by default, and either administrator can add and configure other user accounts. Each local user account is assigned to one or more of the user groups.
CAUTION: Change the default passwords for root and admin before you put the console server into operation.
Local accounts
The admin and root are equivalent users but named differently to address users familiar with either
Avocent equipment or the Cyclades families of ACS console servers. Regular users can be granted permissions by administrators at any time. The ACS 6000 console server has three user account types:
• admin: Performs the initial network configuration. The factory default password for admin is avocent . The admin user is a member of the admin group and can configure the console server and ports as well as user and group authorizations.
• root: Has the same permissions as the admin user. The factory default password for root is linux . In the ACS 6000 console server, the root user is a member of the admin group and shelllogin-profile groups. When a root user logs in via the CONSOLE port, SSH or telnet, the session is pre-defined by the login profile to go directly to shell. The login profile can be customized so that it does not go directly to shell.
• Administrator-added regular users: Have limited access to the Web Manager features based on the group(s) to which they are assigned. Users can change their own passwords. By default, all users have access to all enabled ports.
To add new users:
1.
Click Users - Local Accounts - User Names. The User Names screen is displayed with a list of all users.
2.
Click Add. The Local User Information screen is displayed.
3.
Enter the new username and enter a password, then confirm the password.
4.
Select or deselect User must change password at the next login checkbox.
5.
If you wish to add the user to an available user group, select the user group name in the box on the left and click Add (user is the default group). You can remove a user group from the box at right by selecting it and clicking Remove.
6.
Enter the desired parameters for Password Expiration.
46 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
• Min Days: Enter the minimum number of days allowed between password changes.
Password changes attempted sooner will be rejected. If not specified, -1 is the default which disables the restriction.
• Max Days: Enter the maximum number of days a password is valid. After this period, a password change will be forced. If not specified, -1 is the default which disables the restriction.
• Warning Days: Enter the number of days that a warning is issued to the user prior to expiration. Entering 0 will cause the warning to be issued on the expiration day. A negative value or no value means that no warning will be issued.
7.
Enter the desired Account Expiration date ( YYYY-MM-DD ).
8.
Click Save.
To configure password rules:
1.
Click Users - Local Accounts - Password Rules.
2.
If password complexity is desired (recommended), make sure Check Password Complexity is selected.
3.
If password complexity is enabled, enter the desired values for password complexity.
4.
Enter the desired values for Default Expiration.
5.
Click Save.
User groups
User groups are given access and authorizations either by default or as assigned by an administrator. Administrators can alter the permissions and access rights of users belonging to the appliance-admin or user groups or create additional groups with custom permissions and access rights. Administrators can add, delete or modify permissions and access rights for users from any group at any time.
If an administrator configures the console server to restrict user access to ports, the administrator can assign users to groups that are authorized for port access. The administrator can also authorize groups for power management and data buffer management.
This document and the software refer to users whose accounts are configured on remote authentication servers as remote users. Remote users do not need local accounts.
Radius, TACACS+ and LDAP authentication services allow group configuration. If a remote user is configured as a member of a remote group, the authentication server provides the group name to the console server when it authenticates the user. A local group by the same name must also be configured on the console server. If an authentication server authenticates a remote user but does not return a group, then the remote user is, by default, assigned to the user group.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 47 admin group
Members of the admin group have full administrative privileges that cannot be changed, the same access and configuration authorizations as the default admin user. Administrators can configure ports, add users and manage power devices connected to the console server.
NOTE: The only configuration allowed for the admin group is adding or deleting members.
To view admin Appliance Access Rights:
1.
Click Users - Authorization - Groups. The Group Names screen is displayed, showing the three default user groups along with any groups that have been created.
2.
Click on admin under the Group Name heading. The content area will display the Members screen listing all members belonging to the admin group (default members are admin and root users).
NOTE: When any Group Name is selected, both the content area and side navigation bar change. The side navigation bar will display specific menu options for Members and Access Rights (which include Serial, Power and Appliance rights).
3.
In the side navigation bar, click Access Rights - Serial or Access Rights - Power to access the screens displaying the fixed access rights and permissions for members of the admin group pertaining to serial ports and power management.
NOTE: The Serial and Power screens are read-only and cannot be changed.
4.
In the Side Navigation Bar, click on Access Rights - Appliance. The Appliance Access Rights screen appears and lists all access rights available to a member belonging to the admin group.
All appliance access rights are shown enabled (checked). Available appliance access rights are:
• View Appliance Information
• Disconnect Sessions and Reboot Appliance
• Appliance Flash Upgrade and Reboot Appliance
• Configure Appliance Settings
• Configure User Accounts
• Backup/Restore Configuration
• Shell Access
• Transfer Files
NOTE: The Appliance Access Rights screen for the admin and appliance-admin user groups is read-only and cannot be changed. Unchecking any box and clicking Save will result in an error message. The console server will maintain all rights selected.
appliance-admin group
Members of the appliance-admin group have access restricted to tasks for managing only the appliance. Appliance-admin user group members have no access to the serial ports or power
48 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide management options, and share all of the appliance access rights as admin except for Configure
User Accounts and Shell Access, which are permanently disabled for this group.
user group
Members of the user group have access to target devices unless they are restricted by an administrator but have no access rights for the console server. Administrators can add appliance access rights and permissions, or can add users to custom user groups to add permissions and access rights as needed. By default, all selections on the Appliance Access Rights screen will be disabled.
NOTE: The Appliance Access Rights screen for the user group can be changed at any time by an administrator.
This will change the access rights for all members of the console server’s user group.
shell-login-profile
Members of the shell-login-profile group have access to the shell after logging in. By default, the root user belongs to this group. This is not a protected group and can be deleted.
Managing user groups
Administrators and members of the admin group can create custom user groups that contain any users. Permissions and access for custom user groups will be determined by the top-level user group permissions.
To create a custom user group:
1.
Click Users - Authorization - Groups. The Groups screen is displayed and contains a list of the three default user groups and any additional custom user groups that have been created.
2.
Click Add in the content area.
3.
Enter the name of the new user group you are creating.
4.
Click Save.
To add members to a user group:
1.
Click Users - Authorization - Groups.
2.
Click the user group name.
3.
Click Add. The Members Assignment screen is displayed showing a list of available users in the left box and an empty box on the right.
4.
Move users from the Available Users box on the left to the box on the right by double-clicking on the username, or by selecting the name and clicking the Add button. You can remove any names from the box on the right by double-clicking on the name or by selecting the name and clicking the Remove button.
5.
If you want to add remote users to the new user group (these must be valid names in your remote authentication server), add them in the New Remote Users field.
6.
Click Save.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 49
To remove members from a user group:
1.
Click Users - Authorization - Groups.
2.
Click the user group name.
3.
Check the box(es) of the member(s) you want to remove. Click Delete to delete the selected members.
To configure a login profile for a user group:
1.
Click Users - Authorization - Groups.
2.
Click on the name of the group whose login profile you want to set. In the Side Navigation Bar, click Login Profile.
3.
Check the Enable Log-In Profile box.
4.
Click ts_menu to use the ts_menu application when a member of the selected user group opens a session in the console server. Enter the ts-menu options in the Options field.
-or-
Click CLI to use CLI when opening a session. Enter the CLI command in the CLI cmd field and check the box if you want to exit after executing the command.
5.
Click Save.
NOTE: If the user belongs to multiple groups, the login profile used will be the first enabled login profile based on alphabetical order of the group.
Table 3.8: ts_menu Options
Command
-p
-i
-i6
-u <name>
-e <[^]char>
-l
-ro
<portname>
-t
Description
Displays TCP port
Displays local IPv4 assigned to the serial port
Displays local IPv6 assigned to the serial port
Username to be used in the target session
Escape character used to close the target session
Sorted lists ports and exit
Read-Only mode
Connect directly to a serial port
Idle time-out in seconds to choose the target
50 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
To add access to serial ports for a user group:
1.
Click Users - Authorization - Groups.
2.
Click the new user group name.
3.
In the Side Navigation Bar, click Access Rights.
4.
In the content area, click Add.
5.
Move serial target devices from the Available Target box on the left to the box on the right by double-clicking on the serial target name, or by selecting the target and clicking the Add button. You can remove any targets from the box on the right by double-clicking on the target or by selecting the target and clicking the Remove button.
6.
Select the desired access rights.
7.
Click Save. The Serial screen will appear and show the serial target devices you have authorized for use by the user group with configured permission(s).
8.
Edit the access rights by selecting the checkbox next to one or more of the target names in the list as needed and click Edit. The Target Access Rights screen is displayed with the access rights. Select the desired access rights and click Save.
To assign PDU access for a user group:
NOTE: Assigning PDU access to a user group gives them full access to all power management functions for that
PDU. If you want the user group to have access to outlets only, use the procedure To assign outlet access for a
new custom user group below.
1.
Click on Users - Authorization - Groups.
2.
Click on the user group name.
3.
In the Side Navigation Bar, click Access Rights - Power.
4.
In the content area, click Add. The PDU Assignment screen appears with the list of available
PDUs in the left box.
5.
Move PDU devices from the Available PDU box on the left to the box on the right by doubleclicking on the PDU name, or by selecting the PDU and clicking the Add button. You can remove any PDUs from the box on the right by double-clicking on the PDU name or by selecting the PDU and clicking the Remove button.
6.
You can specify a custom PDU ID in the field at bottom and assign it a custom PDU ID.
NOTE: The custom PDU ID is for assigning user group authorization to manage PDUs that have not yet been connected to the console server.
7.
Click Save.
To assign outlet access for a new custom user group:
NOTE: Assigning outlet access to user groups allows group members to turn outlets on or off, and enable locking and power cycle capabilities on compatible PDUs.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 51
1.
Click Users - Authorization - Groups.
2.
Click on the new user group name.
3.
In the Side Navigation Bar, click Access Rights - Power - Outlets.
4.
Click Add. The Add Outlet screen is displayed.
5.
For connected PDUs, click the Select PDU button to activate the Connected PDUs and Outlets fields.
6.
Select Connected PDU from the pull-down menu.
7.
Enter the outlets assigned to the user group.
NOTE: Outlets can be specified individually, (for example 1,3,6,8) or as a range (for example 1-4) or a combination of both, (for example 1-4,6,8 which assigns access to outlets 1, 2, 3, 4, 6 and 8).
8.
If a custom PDU ID has been created for future use, and you want to pre-assign outlets, click the Custom button to enter the custom PDU ID name and specify the outlets.
9.
Click Save.
To assign appliance access rights for custom user groups:
1.
Click Users - Authorization - Groups.
2.
Click the new user group name.
3.
In the Side Navigation Bar, click Access Rights - Appliance.
4.
Select the desired appliance access rights and click Save.
Event Notifications
The ACS 6000 console server will generate notifications for a wide variety of events. You can configure the console server to direct or store those event notifications to various destinations for immediate use or for analysis later.
Event List
The Event List screen lists ACS 6000 console server events, each of which can be configured for
SNMP Traps, Syslog, DSView, Email and SMS.
To configure Events:
1.
Click Events and Logs - Events.
2.
Locate the events for which you want notification sent and select the checkbox or checkboxes next to the event number(s).
3.
Click Edit.
4.
If you want an event notification sent for any configured event destination type, click its associated Send checkbox.
5.
Click Save. The Events page appears with an X in the column below the destination type if the
Send box was checked on the Events Settings screen.
52 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Event Destinations
The ACS 6000 console server will generate notifications for a wide variety of events. You can configure the console server to direct or store those event notifications to various destinations for immediate use or for analysis later.
To configure Event Destinations:
1.
Click on Event and Logs - Event Destinations.
2.
Under the Syslog heading, use the drop-down menu to select the Facility.
3.
Select Remote Server - IPv4 to enable syslog messages to be sent to one or more remote IPv4 syslog servers, and enter the IPv4 Address or Hostname. Separate multiple server addresses by commas.
-or-
Select Remote Server - IPv6 to enable syslog messages to be sent to one or more remote IPv6 syslog servers, and enter the IPv6 Address or Hostname. Separate multiple server address by commas.
4.
Select Appliance Console to send messages to the ACS 6000 console server’s console.
5.
Select Root Session to send syslog messages to all sessions where you are logged in as root user.
6.
Under the SNMP Trap heading, enter the name of the community defined in one or more of the
SNMP trap servers in the Community field then enter the IP addresses of up to five servers in the server fields.
7.
Under the SMS heading, enter the SMS Server, Port and Pager Number information in the appropriate fields.
8.
Under the Email heading, enter the Server, Port and Destination Email information in the appropriate fields.
9.
Under the DSView heading, enter the IP address of the DSView 3 server where event notifications will be sent in the DSView 3 server field. Enter the syslog server port number for the DSView 3 server, the SSH information and the buffer warning information in the appropiate fields.
10. Click Save.
Data Buffering
To configure Data Buffering:
1.
Select Events and Logs - Data Buffering.
2.
Enter the segment size in kilobytes and spare segments in the Local Data Buffering Settings section.
3.
In the NFS Data Buffering Settings section, enter the following information: NFS Server, NFS
Path, Segment Size (Kbytes) and Spare Segments.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 53
NOTE: RPC service must be enabled in the Security Profile screen before configuring NFS Data Buffering
Settings. NFS does not support IPv6.
4.
To configure data buffer storage on a syslog server in the Syslog Data Buffering Settings section; select a facility number from the drop-down menu: Log Local 0, Log Local 1, Log
Local 2, Log Local 3, Log Local 4 or Log Local 5.
5.
Click Save.
Appliance Logging
To configure Appliance Logging:
1.
Click Enable appliance session data logging.
a.
Select the destination for appliance session data logs from the pull-down menu. Choices are Local, NFS, Syslog and DSView.
b.
Enable or disable timestamping the appliance session data logs.
2.
Click Enable appliance session data logging alerts.
3.
Enter the desired alert strings (up to ten) in the fields provided.
4.
Click Save.
Sensors
The console server has sensors that monitor the internal temperature. You can specify an operating range for the console server that fits its environment.
CAUTION: Do not use values that exceed the maximum and minimum temperatures listed in Techical
To configure the temperature sensors:
1.
Click Events and Logs - Sensors.
2.
In the Maximum Temperature field, enter the temperature in degrees Celsius that, if exceeded, will generate an event notification.
3.
In the Maximum Temperature Threshold field, enter the temperature threshold in degrees
Celsius below the maximum temperature.
NOTE: The Maximum Temperature Threshold field will define a region around the maximum temperature. When the temperature exceeds the Maximum Temperature plus Threshold, an event notification will be generated.
When the temperature falls below the Maximum Temperature minus Threshold, an even notification that the console server has returned to normal operating temperature will be generated. This is also true for setting the minimum temperature threshold.
4.
In the Minimum Temperature field, enter the temperature in degrees Celsius that, if the console server’s temperature falls below, will generate an event notification.
5.
In the Minimum Temperature Threshold field, enter the temperature threshold in degrees
Celsius above the minimum temperature.
54 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
6.
Click Save.
Power Management
Connected power devices can be used for remote power management. The ACS 6000 console server enables users who are authorized for power management to turn power on, turn power off and reset devices that are plugged into a connected PDU.
The following types of power devices can be connected to any serial port or to the AUX/Modem port (if an internal modem is not installed):
• Avocent Power Management Power Distribution Unit (PM PDU).
• Cyclades PM Intelligent Power Distribution Units (IPDUs) - With Cyclades PM IPDUs, up to
128 outlets can be daisy-chained and managed from a single serial port.
• Avocent SPC power control devices.
• Server Technology Sentry™ family of Switched Cabinet Power Distribution Units (CDUs) and switched CDU Expansion Module (CW/CX) power devices. One additional level of power devices can be daisy-chained with ServerTech Expansion modules.
• Server Technology Sentry Power Tower XL™ (PTXL) and Power Tower Expansion Module
(PTXM) power devices.
NOTE: The term PDU refers to any of these types of power devices.
PDUs
The ACS 6000 console server automatically recognizes and supports Avocent PM PDUs, Cyclades
PM IPDUs or Avocent SPC devices when the corresponding serial port is configured for power management.
For supported Server Technology PDUs, the ACS 6000 console server must be managed by a
DSView 3 server (version 3.6.0.152 or greater), the needed power device license must be present and the power device must be added to the DSView 3 software.
The license is automatically downloaded from the DSView 3 server onto the ACS 6000 console server, and then configuration and management can be performed either through the DSView software or through the Web Manager.
To manage a PDU:
1.
Select Power Management - PDUs.
2.
Select the checkbox next to the PDU for which you want to manage power.
3.
Click On, Off, Cycle, Reboot PDU, Reset HW Overcurrent Protection or Factory Defaults if desired. A confirmation appears. Click OK.
NOTE: The power controls (On, Off and Cycle) will be applied to all outlets of the PDU.
4.
To change the PDU ID, click Rename and enter the name in the New PDU ID field.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 55
5.
Click Save.
To view a PDU’s information:
1.
Select Power Management - PDUs.
2.
Click the name of the PDU you want to view or manage.
3.
The Outlet Table with power controls window appears and the Side Navigation Bar displays a list of options.
4.
To manage outlets of PDU: a.
Check the box(es) of the outlet number(s) you want to manage.
b.
Click On, Off, Cycle, Lock or Unlock to perform that function for the selected outlet(s).
5.
Click Information in the Side Navigation Bar to view a PDU’s information.
6.
Click Current, Voltage, Power Consumption, Cumulative Power or Environment in the Side
Navigation Bar to view a table with appropriate information. Click Reset Values to clear Max,
Min and Average values.
To upgrade firmware (Cyclades PM PDU only):
1.
Click Overview in the Side Navigation Bar and click on Upgrade Firmware.
2.
Fill all fields with correct information and click Download to download the firmware to the
ACS 6000 console server.
3.
When the download finishes, the Install PM Firmware screen appears. If the version information is correct, click Upgrade Now to start the upgrade of the firmware in the PDU.
4.
When the upgrade finishes, the Finish Upgrade screen appears with the result of the upgrade action. Click Finish.
To manage outlets on a PDU:
1.
Click Settings to expand the Side Navigation Bar.
2.
Click Outlets.
3.
Click on an outlet number to change its settings. You can change the Name, Post On Delay,
Post Off Delay, Current Critical Threshold, Current Warning Threshold and Current Low
Warning Threshold.Click Save, then click Close.
-or-
Check two or more boxes next to the outlets for which you want to change settings. Click Edit.
You can change the Prefix Name (the outlet name will be Prefix Name and the Suffix), Post
On Delay, Post Off Delay, Current Critical Threshold, Current Warning Threshold and Current
Low Warning Threshold. Click Save.
4.
Click PDU to see PDU settings. You can change the Nominal Voltage, Power Factor and
Current Threshold(s). Click Save when finished.
5.
Click Phases or Banks.
56 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide a.
Click on the name of a phase or bank to change its settings, or click one or more boxes next to the phase(s) or bank(s) you want to change. You can change the Current Critical
Threshold, Current Warning Threshold and Current Low Warning Threshold. b.
Click Save to save the settings and click Close to return to the Phase screen.
NOTE: The PDU model defines available parameters in the Settings window.
Login
An administrator can change the login password for a supported PDU type. This password is used by the console server to communicate with the PDU. (Only one password is supported for all PDUs of the same type.)
To change a PDU password:
1.
Select Power Management - Login.
2.
To change the password for an Avocent or Cyclades PDU, an Avocent SPC power control device or a Server Tech PDU, enter the password in the appropriately labeled section.
3.
Click Save.
Outlet Groups
By selecting the Outlet Groups tab, you can view status, outlet and power consumption for outlet groups, as well as configure them. You can also turn on, turn off or cycle selected outlet groups.
To manage outlet groups:
1.
Select Power Management - Outlet Groups.
2.
Check the box next to the name of the Outlet Group you want to manage.
3.
Click the On, Off or Cycle radio button, if desired.
-or-
4.
Click Add to add an outlet group. The Add Group screen appears. Enter the name in the Group
Name field.
5.
Click Save.
To view and change outlet group information:
1.
Select Power Management - Outlet Groups.
2.
Click the name of the outlet group you want to view or manage.
3.
To add outlets, click Add to add a new outlet to the group. Fill the fields and click Save to return to the Outlet Group Details table.
4.
To delete outlets, check one or more boxes next to the outlet(s) you want to remove from the group. Click Delete, then click Close when finished.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 57
Active Sessions
The ACS 6000 console server allows multiple users to log in and run sessions simultaneously. The
Active Sessions feature allows you to view all active sessions and to kill any unwanted sessions.
Click Active Sessions to view all open sessions on the console server.
NOTE: If you start another session with the console server while viewing this screen, it will not be visible until you click Refresh at the top of the Web Manager window.
To kill an active session:
1.
Click Active Sessions. The Active Sessions screen appears and lists all open sessions to the console server by the user’s workstation IP.
2.
Select the checkbox next to the session you want to kill, then click the Kill button. After a few seconds, the Active Session screen will redisplay the open sessions, minus the one you killed.
Monitoring
When you click Monitoring, a variety of network and console port information is available for viewing. The screens are only for viewing and have no interactivity with the user. The following table shows the types of information available.
Table 3.9: Monitoring Screens
Screen Name
Network - Devices
Definition
Shows Ethernet ports and PC card Device Name, Status (enabled/disabled),
IPv4 Address, IPv4 Mask and IPv6 Address.
Network - IPv4 Routing Table Shows Destination, Gateway, Genmask, Flags, Metric, Ref, Use and lface.
Network - IPv6 Routing Table Shows Destination, NextHop, Flags, Metric, Ref, Use and lface.
Serial Ports Shows Device Name, Profile, Settings, Signals, TX Bytes, RX Bytes, Frame
Error, Parity Error, Break and Overrun.
Change Password
An admin or user can change his or her own password from this screen.
To change your own password:
1.
Select Change Password.
2.
Enter the old password and new password in the appropriate fields.
3.
Confirm the new password, then click Save.
58 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Web Manager Overview for Regular Users
The following figure shows features of the Web Manager for a regular user.
1
2
3
Figure 3.3: Web Manager Regular User Screen
Table 3.10: Web Manager Regular Users Screen Functional Areas
2
3
Number Description
1 Top option bar. The name of the appliance and the name of the logged in user appears on the left side and Refresh, Print, Logout and Help buttons appear on the right.
Side navigation bar. Menu options appear that are available for regular users.
Content area. Contents change based on the options selected in the side navigation bar.
The following table provides an overview of the options for regular users.
Table 3.11: Web Manager Options for Regular Users
Menu Option
Access
Description
Displays all the devices the user can access. Click on Serial Viewer in a device’s
Action column to launch a terminal session with that device.
Chapter 3: Accessing the ACS 6000 Console Server via the Web Manager 59
Table 3.11: Web Manager Options for Regular Users (Continued)
Menu Option
Power Management
• PDUs
• Outlet Groups
Change Password
Description
• Click PDUs to turn on, turn off, cycle, reboot, reset the HW overcurrent protection, returnt to factory defaults or rename PDUs connected to the console server.
• Click Outlet Groups to manage groups of outlets on connected PDUs.
Change your own password.
60 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
A P P E N D I C E S
Appendices
Appendix A: Techical Specifications
Table A.1: Technical Specifications for the ACS 6000 Console Server Hardware
General Information
CPU
Memory
Interfaces
PPC440EPx @ 533 MHz (PowerPC with Security Acceleration Engine)
256 MB DDR-2 / 128 MB NAND Flash (embedded ICs on motherboard)
2 Ethernet 10/100/1000BT on RJ-45
1 RS232 Console on RJ-45
1 AUX RS232 on RJ-45 or internal MODEM V.92 on RJ-45 (RJ11 compatible)
RS232 Serial Ports on RJ-45
1 USB 2.0 Host on Type A connector
2 PC Card / CardBus with ejector (dual Type II or single Type III)
Power Information
Power Supply
Power Consumption
Height x Width x Depth
Weight
Internal 100-240 VAC, 50/60 Hz
Optional Dual entry, redundant power supplies
-48 VDC option available
Nominal voltage 120 VAC:
Typical 0.17 A, 20 W
Maximum 0.25 A, 30 W
Nominal voltage 230 VAC:
Typical 0.1 A, 23 W
Maximum 0.15 A, 35 W
Nominal voltage -48 VDC (20% tolerance)
Typical 0.5 A
Ambient Atmospheric Condition Ratings
Operating Temperature 32
o
F to 122
o
F (0 o
C to 50 o
C)
Storage Temperature -4
o
F to 158
o
F (-20 o
C to 70 o
C)
20% to 80% relative humidity (non-condensing) across the operating temperature range Humidity
Dimensions
1.715 x 17.250 x 9.50 in
(4.3561 x 43.815 x 24.13 cm)
6.6 pounds (2.994 kg)
61
62 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Table A.1: Technical Specifications for the ACS 6000 Console Server Hardware (Continued)
Certifications
Emissions and Immunity: FCC Class A (USA), CE Class A (EU), ICES-003 (Canada), VCCI
(Japan), C-Tick (Australia, no internal modem), A-Tick (Australia)
Safety: UL 60950-1 (USA), cUL (Canada), EN-60950-1 (EU), CB
Appendices 63
Appendix B: Recovering an ACS 6000 Console Server Password
To recover the ACS 6000 console server root password:
1.
Connect directly to the console server’s CONSOLE port.
2.
Turn the console server off, then on again.
3.
Press the Spacebar to access the uboot prompt.
4.
Type hw_boot single and press Enter .
5.
The console server will boot into single-user mode. Type passwd and press Enter .
6.
Enter the new password and confirm.
7.
Type reboot and let the console server boot normally.
64 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Appendix C: Accessing a Console Server with a DSView 3
Software Installation via Dial-up
When a DSView 3 software user establishes a serial session, the following events occur:
• The user selects a serial port to access.
• A viewer is downloaded from the DSView 3 server to the user's workstation.
• The DSView 3 software passes information to the viewer, such as an authorization key, the console server's IP address and serial port.
• The viewer then accesses the console server's serial port through an SSH session by passing the authorization key obtained from the DSView 3 server.
• The serial session begins.
To ensure constant connectivity, a DSView 3 server can be configured with an out of band (OOB)
“back door” that will allow it to call a console server via modem in the event of a network or
Internet failure.
Installing DSView 3 software with an OOB back door
The DSView 3 server must be running on hardware that has a connected modem, and the console server must have a built-in modem or access to a modem via a PCMCIA card, USB or serial port.
For this installation, the DSView 3 server must be the central point of reception of both the packets leaving the downloaded viewer and the console server. To ensure this, Proxy mode must be configured within the DSView 3 software. The viewer will then point to the DSView 3 server (not the console server) to establish the SSH connection. The DSView 3 server would then route the packets by changing both the source and destination IP addresses and act as a middle point of communication.
Under normal operating conditions, packets received from the Video Viewer would route through the DSView 3 server via Ethernet. In an error state, the DSView 3 server would detect that the normal path to the console server was interrupted and would dial out to the console server, pass authentication and establish a PPP connection. Packets that would normally pass via Ethernet would instead be routed via PPP.
Because of the speed differences between Ethernet and dial-up, performance would be notably slower, but still present. Multiuser connections would further degrade performance and are not recommended. For this reason, dial-up backup is recommended as an emergency backup feature only.
Configuring dial-up for an ACS 6000 console server
To configure dial-up to a console server within the DSView 3 software:
1.
In a Units view window containing appliances, select the ACS 6000 console server you want to configure. For dial-in with callback, you must first select DSView Server - Properties -
DSView Modem Sessions under the System tab and enter the the phone number assigned to the
DSView 3 server in the Analog Phone Number field.
Appendices 65
2.
Select DSView Settings - Dial-up.
3.
Select Modem Type - Analog.
4.
Enter the phone number for the ACS 6000 console server you want to use.
5.
Enter the PPP User and select the PPP Auth Protocol in the appropriate fields.
6.
For dial-in with callback, enable the dial-back checkbox.
7.
Select DSView Settings - Dial-up - PPP Password, then enter and confirm the password needed to access the ACS 6000 console server.
8.
Select DSView Settings - Dial-up - IP Addresses.
9.
Click Generate Automatically to set the IP address automatically, or enter the PPP Local IP address and Appliance IP address manually.
To configure a console server to receive the dial-up connection within the DSView
3 software:
1.
In a Units view window containing appliances, select the ACS 6000 console server you want to configure.
2.
For a modem attached to a serial port, select Ports - Serial Ports, then select the port that contains the attached modem. Click Set Dial-In.
-or-
For a modem attached to an auxiliary port, select Ports - Auxiliary Ports, then select the port.
Click Set Dial-In.
-or-
For an internal modem, select Ports - Auxiliary Ports and select the modem.
-or-
For a pluggable device modem, select Pluggable Devices and select the modem.
3.
For dial-in with callback, click Ports - Dial-in Profile - Devices and select the modem to be used for dial-in.
-or-
For dial-in with a one-time password (OTP), click Ports - Dial-in Profile - Secure Dial-in -
Settings and select Enable next to the Log In To Appliance field.
4.
Select Accept Configuration from Remote Peer in the PPP Address field.
5.
Select By Appliance in the PPP Authentication field and set the protocol.
-or-
For dial-in with callback, select By Remote Peer in the PPP Authentication field and select the protocol.
6.
Click Ports - Dial-in Profile - Settings and select Disable in the Log In To Appliance field.
(You may select Enable if you want to get terminal access besides PPP or Callback if you want terminal access only for callback.)
66 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
-or-
For dial-in with OTP, click Ports - Dial-in Profile - Settings and select Enable if you want the console server to receive non-OTP connections.
7.
Select Disable in the OTP Login Authentication field.
-or-
For dial-in with OTP, select Enable in the OTP Login Authentication field.
8.
Select Enable in the PPP Connection field.
-or-
For dial-in with OTP, select Disable in the PPP Connection field if you want the console server to receive non-OTP connections.
9.
Select Local in the PPP/PAP Authentication field.
10. For dial-in with callback, click Ports - Dial-In Profile - Callback Users and add the PPP user and callback number in the appropriate fields.
-or-
For dial-in with OTP, click Ports - Dial-In Profile - Secure Dial-In - PPP - OTP Users and add the OTP user.
11. Click Users - Local Accounts - User Names and add the PPP User and password in the appropriate fields.
NOTE: The following step is only required if CHAP was selected in the PPP Auth Protocol field in the DSView 3 software Settings Dial-up window.
12. Log in to the console server’s CLI and access the Linux shell. Edit the /etc/ppp/chap-secrets and add a line in the format, where the first column should have the PPP user and the third column should have the PPP password as is shown in the following example: pppuser * "ppppassword" *
Appendices 67
Appendix D: Internal Modem
Some models of the ACS 6000 advanced console server come equipped with an internal modem.
This modem is used to originate and answer phone calls and establish communication with other modems to transmit data.
Controlling the modem’s functions is done by using the “AT” commands. These commands are used to instruct the modem to perform functions such as dialing or answering calls and are normally automatically issued by communication software. However, for some applications, custom software may have to be written due to the absence of a normal operating system.
The modem will automatically accept and process AT commands at most standard DTE (Data
Terminal Equipment) speeds and parity settings. For each command issued, the modem will respond with a result code to inform you of the modem’s status. The format of a basic AT command and result code is as follows:
AT<Command><CR>
OK
AT = Attention.
<Command> = any valid command
<CR> = Carriage Return or Enter key
OK = Result Code
Table D.1: Sample Command String
Command
ATDT7678900<CR>
ATS0=2<CR>
Description
Instructs the modem to dial the number 7678900 and attempt to connect to the remote device.
Enables auto answer option. When the modem detects a ring, it will attempt to answer after two rings.
Table D.2: Basic AT Commands
Command
ATA/
ATA
ATB0
ATB1
ATD
ATD0-9
Description
Repeat the previous command.
Answer.
CCITT operation at 300 or 1200 bps.
Bell operation at 300 or 1200 bps (default).
Dial.
Dial the DTMF digits 0 to 9.
68 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
ATL0
ATL1
ATL2
ATL3
ATM0
ATM1
ATD;
ATE0
ATE1
ATH0
ATH1
ATI0
ATI2
ATI3
Table D.2: Basic AT Commands (Continued)
Command
ATDA-D
ATDP
ATDT
ATD!
ATDW
ATD@
ATD,
ATM2
ATM3
ATQ0
Description
Dial the DTMF digits A, B, C and D.
Select pulse dialing; effects current and subsequent dialing.
Select tone dialing; effects current and subsequent dialing.
Flash: go on-hook by time defined by S29.
Wait for dial tone detection before dialing a number. If no dial tone is detected within the time specified by S7, the modem aborts the rest of the sequence, goes on-hook and generates an error message.
Wait for five seconds of silence before proceeding with next dialing string and then complete handshake sequence.
Pause. The modem pauses for a time specified by S8 before dialing the number.
Most often used when dialing an outside line through a PBX.
Return to the command mode after processing the command.
Disables the command echo.
Enables the command echo (default).
Hang up.
Forces the modem off-hook.
Reports product code.
Reports OK (for software compatibility).
Reports the firmware version of the modem. Example: CX810801-V90.
Sets the speaker volume off.
Sets the speaker volume low (default).
Sets the speaker volume medium.
Sets the speaker volume high.
Speaker is always off.
Speaker is on during call establishment but goes off when carrier is detected
(default).
Speaker is always on.
Speaker if off during dialing and when receiving carrier but on during answering.
Enables result codes to the DTE (default).
Appendices 69
Table D.2: Basic AT Commands (Continued)
Command
ATQ1
ATSr
ATSr=n
ATSr?
ATV0
ATV1
ATW0
ATW1
ATW2
ATX0
ATX1
ATX2
ATX3
ATX4
ATZ0
AT&C0
AT&C1
AT&D0
Description
Disables result codes to the DTE.
Establishes S-register “r” as the default register.
Sets S-register “r” to the value “n.”
Reports the value of S-register “r.”
Enables short-form result codes.
Enables long-form result codes.
Upon connection, the modem reports only the DTE speed (for example,
CONNECT 9600). Subsequent responses are disabled (default).
Upon connection, the modem reports the modulation type, line speed, the error correction protocol and the DTE speed. Subsequent responses are disabled.
Upon connection, the modem reports DCE speed (for example, CONNECT
2400). Subsequent responses are disabled.
Ignores dial and busy tone. Sends CONNECT message when a connection is established by blind dialing.
Disables monitoring of busy tones. Sends only OK, CONNECT, RING, NO
CARRIER and ERROR messages. If busy tone detection is enforced and busy tone is detected, NO CARRIER will be reported instead of BUSY. If dial tone detection is enforced or selected and dial tone is not detected, NO CARRIER will be reported instead of NO DIALTONE.
Disables monitoring of busy tones. Sends only OK, CONNECT, RING, NO
CARRIER, ERROR, NO DIALTONE and CONNECT XXXX. If busy tone detection is enforced and busy tone is detected, NO CARRIER, will be reported instead of BUSY. If dial tone detection is enforced or selected and dial tone is not detected, NO CARRIER will be reported instead of NO DIALTONE.
Enables monitoring of busy tones. Sends only OK, CONNECT, RING, NO
CARRIER, ERROR, NO DIALTONE and CONNECT or CARRIER XXXX. If dial tone detection is enforced and dial tone is not detected, NO CARRIER will be reported.
Enables monitoring of busy tones. Sends all messages (default).
Soft reset.
DCD remains on at all times.
DCD follows the state of the carrier (default).
Ignores DTR.
70 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
AT&P0
AT&P1
AT&P2
AT&P3
AT&Q0
AT&Q5
AT&Q6
AT&F
AT&G0
AT&G1
AT&G2
AT&K0
AT&K3
AT&K4
AT&K5
Table D.2: Basic AT Commands (Continued)
Command
AT&D1
AT&D2
AT&D3
AT&V
AT%C0
AT%C1
AT%C2
AT%C3
AT%E0
AT%E1
Description
Enters the escape mode when ON-to-OFF transition is detected on DTR.
Hangs up, assumes command state and disables auto answer upon detecting
ON-to-OFF transition of DTR (default).
ON-to-OFF transition causes the modem to perform a soft reset. It is the same as if an ATZ command is issued.
Restores factory configuration.
Disables guard tone (default).
Enables 550-Hz guard tone.
Enables 1800-Hz guard tone.
Disables flow control.
Enables RTS/CTS flow control (default for data modes).
Enables XON/XOFF flow control.
Supports transparent XON/XOFF flow control.
39/61 make/break ratio at 10 pulses per second (default).
33/67 make/break ratio at 10 pulses per second.
39/61 make/break ratio at 20 pulses per second.
33/67 make/break ratio at 20 pulses per second.
Selects direct asynchronous operation.
Modem will try an error-corrected link.
Selects asynchronous operation in normal mode (allows speed buffering and flow control but no error correction).
Displays modem’s current configuration. When this command is entered, the modem will display its current command and register settings.
Disables data compression.
Enables MNP 5 data compression.
Enables V.42 bis data compression (sets S46 bit 1).
Enables V.42 bis and MNP 5 data compression (default).
Disables line quality monitor and auto-retrain.
Enables line quality monitor and auto-retrain.
Appendices 71
Table D.2: Basic AT Commands (Continued)
Command
AT%E2
AT%L
AT%Q
AT+MS
Description
Enables line quality monitor and fallback/fall-forward (default).
Line signal level. Returns a value that indicates the received signal level.
Example, 009 = -9dBM.
Line signal quality. Reports line signal quality (DAA-dependent). Returns higher order byte of the EQM value. Based on EQM value, retrain or fallback/fallforward may be iniated if enabled with AT%E1 or AT%E2 commands.
Select/force modulation.
AT+MS modulation selection
This extended-format compound parameter controls the manner of operation of the modulation capabilities in the modem. It accepts six sub-parameters:
+MS=<carrier>, <automode>, <min_tx_rate>, <max_tx_rate>, <min_rx_rate),
<max_rx_rate><CR>.
To read the current settings, enter AT+MS?<CR>
Table D.3: +MS Command Supported Rates
Modulation Carrier
Bell 103 B103
Bell 212
V.21
B212
V21
V.22
V.22 bis
V.23
V.32
V.32 bis
V.34
V22
V22
V23C
V32
V32B
V34
V.90
K56flex
V90
K56
Possible Minimum, Maximum, Receive and Transmit Rates
300
1200
300
1200
2400 or 1200
1200rx/75tx or 75rx/1200tx
9600 or 4800
14400, 12000, 9600, 7200 or 4800
33600, 31200, 28800, 26400, 19200, 16800, 14400, 12000,
9600, 7200, 4800 or 2400
56000, 54667, 53333, 52000, 50667, 49333, 48000, 46667,
45333, 42667, 41333,, 40000, 38667, 37333, 36000, 34667,
33333, 32000, 30667, 29333, 28000
56000, 54000, 52000, 50000, 48000, 46000, 44000, 42000,
40000, 38000, 36000, 34000, 32000
72 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Table D.3: +MS Command Supported Rates (Continued)
Modulation Carrier
V92 downstream
V92
V92 upstream
V92
Possible Minimum, Maximum, Receive and Transmit Rates
56000, 54667, 53333, 52000, 50667, 49333, 48000, 46667,
45333, 42667, 41333,, 40000, 38667, 37333, 36000, 34667,
33333, 32000, 30667, 29333, 28000
48000, 46667, 45333, 42667, 41333,, 40000, 38667, 37333,
36000, 34667, 33333, 32000, 30667, 29333, 28000, 26667,
25333, 24000
Set telephone extension option
This command enables/disables “line-in-use” and “extension pickup” options.
Table D.4: Set Telephone Extension Options
1
2
-STE=n Value
0 (default)
3
Extension Pickup
Disabled
Disabled
Enabled
Enabled
Line-In-Use
Disabled
Enabled
Disabled
Enabled
If the line is in use and the modem receives an ATDT command to dial out, the modem will not go off hook and will display the “LINE-IN-USE” result code. If the modem is off hook and the extension is picked up, the modem will drop the connection and display the “OFF-HOOK
INTRUSION” result code.
AT S registers
The S registers use the following format: ATSr=n<CR> where the “r” is the S register number and
“n” is the parameter to set it to. To read the current contents of an S register, issue an ATSr?<CR> command where “r” is the register in question. The modem will then display the value of the S register.
Table D.5: AT S Registers
Register Range
S0 0-255
Units
Rings
S1
S2
0-255
0-127
Rings
ASCII
Default
0
0
43
Description
Ring to answer on. ATS0=1<CR> means answer call on first ring detected.
Number of rings counted.
Escape code character.
Appendices 73
Table D.5: AT S Registers (Continued)
S10
S11
S12
S24
S29
S30
S95
S5
S6
S7
S8
Register Range
S3
S4
0-127
0-127
0-127
2-255
1-255
0-255
1-255
50-255
0-127
0-255
0-255
0-255
Units
ASCII
ASCII
ASCII
Seconds
Seconds
Seconds
.1sec
.01sec
1/50 sec
1sec
10mS
10Sec
70
0
0
14
85
50
0
8
2
50
2
Default
13
10
Description
Command terminator<CR>.
Line feed character.
Backspace character.
Wait time for dial-tone detection.
Wait time for carrier.
Pause time for coma in dial string.
Loss of carrier to hang up delay.
DTMF tone duration.
Escape code guard time.
Sleep mode inactivity timer.
Hook flash dial modifier time.
Inactivity disconnect timer.
Result code control.
Basic modem result codes
There are basic codes the modem will issue in response to processing an AT command. Result codes may be displayed either in word (V1) or numeric (V0) format by using the Vn command.
The Qn command controls if result codes are issued (Q0) or not issued (Q1). The Xn, Wn commands and register S95 determines which result code format the modem will display to indicate the type of connection established. There are more than 300 codes. The most commonly used are listed in the table below.
Table D.6: Basic Result Code Listing
Numeric Verbose
0 OK
1 CONNECT
2
3
4
RING
NO CARRIER
ERROR
Description
The modem has received and acknowledged the command.
Connection made at 300bps or extended result codes are off
(X0).
An incoming ring signal has been detected.
This result code reflects either an intended disconnect or a failure to complete a connection.
An invalid command was issued to the modem.
74 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Table D.6: Basic Result Code Listing (Continued)
15
16
17
18
7
8
10
12
Numeric Verbose
5
6
CONNECT 1200
NO DIALTONE
Description
Indicates a 1200bps line or DTE connection.
The modem can not detect a dial tone.
BUSY
NO ANSWER
CONNECT 2400
CONNECT 9600
The modem has detected a busy tone.
After S7 time has elapsed, the remote server never answered.
Line speed or DTE connection at 2400bps.
Line speed or DTE connection at 9600bps.
CONNECT 14400 Line speed or DTE connection at 14400bps.
CONNECT 19200 Line speed or DTE connection at 19200bps.
CONNECT 38400 Line speed or DTE connection at 38400bps.
CONNECT 57600 Line speed or DTE connection at 57600bps.
Digital line guard
The modem has an optional Digital Line Guard Circuit that automatically detects an over current situation on the Tip and Ring pins. When the modem goes off hook, it will immediately check the current on the Tip and Ring pins. If the current exceeds 150 mA, the modem will display the
“DIGITAL LINE DETECTED” result code and then go back on hook. The modem will continue to display this result code until normal current is detected on the Tip and Ring pins during an off hook condition. The DLG feature will protect the modem in case it is accidentally connected to a Digital
Telephone Line.
Sleep mode operation
The modem can be set to enter the low power sleep mode by setting ATS24=n . In this case, “n” is time, in seconds, that the modem will operate in normal mode with no detected telephone line or
DTE line activity before entering low power sleep mode. The timer is reset upon any DTE or telephone line activity. If S24 is set to zero, the modem will never enter the low power sleep mode.
Disconnecting a call
There are several ways to disconnect a call. Below are the choices.
• Resetting the modem’s power or toggling the Reset Line (Pin #12) will disconnect and put the modem back into the OFF line state.
• An ON to OFF transition of the DTR signal (Pin #4) will also disconnect the modem. If you use this method, check to make sure that the DTR command is set to &D2 or &D3 and not forced (&D0).
Appendices 75
• The remote device can also cause the modem to disconnect. If the remote modem disconnects your modem will automatically sense the loss of the carrier signal and return to the OFF line state.
• The ATH or ATZ commands can also be used to disconnect a call. In order to issue a command to the modem when it is On Line, the modem must be placed into the On Line Command State.
This is accomplished by issuing a special escape sequence. The default value of this three digit escape sequence is the “+” character (see S2 to change). The “+++” is protected by a onesecond delay before and after it is sent (see S12 to change the time) When the modem detects the escape sequence, the OK result Result code will be displayed and the modem is in the On
Line Command State. The ATH or ATZ command can now be issued to disconnect the call.
Selecting country codes
Setting the modem’s country code is done by with the +GCI command. To change to one of the 30 available countries, issue the AT+GCI=n command where “n” is one of the two digit country codes.
This command must be issued each the modem is turned on. It will not automatically store or save this setting. It should be part of the Initialization string.
Example: AT+GCI=00<CR> Meaning: Change country code to Japan.
OK Meaning: The modem has accepted the command and is now configured to operate in Japan
AT+GCI?<CR> Meaning: Display current country code
+GCI:00 Meaning: (Japan is the current country selected).
OK
To view which countries are available in the modems firmware, enter AT+GCI=?<CR> .
The modem will display all of the possible two digit country codes available.
Table D.7: Country Codes List
Country
Australia
Austria
Belgium
Brazil
China
Denmark
Finland
France
Germany
16
26
31
3C
Code
09
0A
0F
3D
42
Country
Hong Kong
India
Ireland
Italy
Japan
Korea
Mexico
Netherlands
Norway
59
00
61
73
Code
50
53
57
7B
82
Country
Poland
Portugal
South Africa
Singapore
Spain
Sweden
Switzerland
Taiwan
TBR21
9C
A0
A5
A6
Code
8A
8B
9F
Fe
FD
76 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Table D.7: Country Codes List (Continued)
Country
United States
Code
B5
Country
United
Kingdom
Code
B4
Country Code
Using caller ID
The modem can be used to display certain information about incoming telephone calls. The modem can inform you of the date, time, telephone number and name associated with incoming calls.
When the CID option is enabled, information will be displayed between the first and second incoming “RING.” In order for this feature to work properly, the telephone line connected to the modem must subscribe to caller ID service offered by the local telephone company. A sample of the displayed information is shown below:
RING
DATE = 0513
TIME = 1346
NMBR = 408 767 8900
NAME = RADICOM RESEARCH
RING
The CID information can either be presented formatted as shown previously or unformatted. The
+VCID and +VRID commands control the modem CID option.
Table D.8: Caller ID Information
Command
+VCID?
+VCID=
+VCID=
+VCID+
+VRID=
+VRID+
Parameter
NA
0
1
2
0
1
Description
Display current +VCID setting (0-2)
Disable caller ID reporting (default).
Enable caller ID with formatted presentation to the DTE.
Enable caller ID with unformatted presentation to the DTE.
Displays the formatted caller ID of the last received call.
Displays the unformatted caller ID of the last received call.
Appendices 77
Appendix E: Safety, Regulatory and Compliance Information
Safety, regulatory and compliance information for the ACS 6000 console server is described in this appendix.
Safety and environmental guidelines for rack mounting the console server
The following considerations should be taken into account when rack mounting the Cyclades ACS
6000 advanced console server.
Temperature
The manufacturer's maximum recommended ambient temperature for the ACS 6000 console server is 122 ºF (50 ºC).
Elevated operating ambient temperature
If the console server is installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer’s maximum rated ambient temperature. See above.
Reduced air flow
Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.
Mechanical loading
Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
Circuit overloading
Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
Reliable earthing
Reliable earthing of rack mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit, such as power strips or extension cords.
78 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Safety precautions for operating the ACS 6000 console server
Please read all the following safety guidelines to protect yourself and your Cyclades ACS 6000 advanced console server.
WARNING: Do not operate your Cyclades ACS 6000 advanced console server with the cover removed.
CAUTION: To avoid shorting out your Cyclades ACS 6000 advanced console server when disconnecting the network cable, first unplug the cable from the Host Server, unplug external power (if applicable) from the equipment and then unplug the cable from the network jack. When reconnecting a network cable to the back of the equipment, first plug the cable into the network jack and then into the host server equipment.
CAUTION: To help prevent electric shock, plug the Cyclades ACS 6000 advanced console server into a properly grounded power source. The cable is equipped with a three-prong plug to help ensure proper grounding. Do not use adaptor plugs or remove the grounding prong from the cable. If you have to use an extension cable, use a three-wire cable with properly grounded plugs.
CAUTION: To help protect the Cyclades ACS 6000 advanced console server from electrical power fluctuations, use a surge suppressor, line conditioner or uninterruptible power supply. Be sure that nothing rests on the cables of the console server and that they are not located where they can be stepped on or tripped over. Do not spill food or liquids on console server.
CAUTION: Do not push any objects through the openings of the Cyclades ACS 6000 advanced console server.
Doing so can cause fire or electric shock by shorting out interior components.
CAUTION: Keep your Cyclades ACS 6000 advanced console server away from heat sources and do not block host’s cooling vents.
CAUTION: The Cyclades ACS 6000 advanced console server DC models are to be installed with a maximum
20A Listed circuit breaker or branch-rated fuse.
CAUTION: The Cyclades ACS 6000 advanced console server DC-powered models are only intended to be installed in restricted access areas (dedicated equipment rooms, equipment closets or the like) in accordance with Articles 110-18, 110-26 and 110-27 of the National Electrical Code, ANSI/NFPA 701, 1999 Edition. Use 18
AWG or 0.75 mm2 or above cable to connect the DC configured unit to the Centralized D.C. Power Systems.
Install the required double-pole, single-throw, DC rated UL Listed 20A listed circuit breaker or branch-rated fuse between the power source and the Cyclades ACS 6000 advanced console server DC version. Minimum Breaker
Rating: 2A. Required conductor size: 18 AWG or larger.
CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger UL Listed or CSA Certified
Telecommunication Line Cord (for example, 24 AWG).
Working inside the console server
Do not attempt to service the console server yourself, except when following instructions from
Avocent Technical Support personnel. In the latter case, first take the following precautions:
• Turn the console server off.
• Ground yourself by touching an unpainted metal surface on the back of the equipment before touching anything inside the unit.
Appendices 79
NOTE: To comply with FCC standards, the ACS 6000 console server requires the use of a shielded CAT 5 cable for all port connections. Notice that this cable is not supplied with either of the products and must be provided by the customer. See the inside cover for the FCC Warning Statement and Canadian DOC Notice.
Electrostatic Discharge (ESD) precautions
When handling any electronic component or assembly, you must observe the following antistatic precautions to prevent damage.
• Always wear a grounded wrist strap when working around printed circuit boards.
• Treat all assemblies, components and interface connections as static-sensitive.
• Avoid working in carpeted areas.
• Keep body movement to a minimum while removing or installing boards to minimize the buildup of static charge.
Replacing the battery
CAUTION: There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
FCC requirements for the internal modem
For models equipped with an internal modem, the Federal Communication Commission (FCC) has established rules, which permits this device to be directly connected to the telephone network. If this device is malfunctioning, it may also be causing harm to the telephone network; this device should be disconnected until the source of the problem can be determined and until repair has been made. If this is not done, the telephone company may temporarily disconnect service. The telephone company may make changes in its technical operations and procedures; if such changes affect the compatibility or use of this device, the telephone company is required to give adequate notice of the changes. If the telephone company request information on what equipment is connected to their lines, inform them of the following:
• The telephone number and the device it is connected to.
• The ringer equivalence number (REN).
• The device uses an RJ-45 type jack.
• The FCC Registration Number.
The REN (Ringer Equivalence Number) is used to determine the number of devices that may be connected to the telephone line. Excessive RENs on a telephone line may result in devices not ringing in response to an incoming call. In most, but not all areas, the sum of the REN should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or any other electronic device, including fax machines, to send any message unless such
80 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any number for which charges exceed local or long distance transmission charges.) This equipment must not be used on party lines. Connection to party line service is subject to state tariffs. Contact state public utility commission for information. In order to program this information into your fax machine or fax / modem, consult your fax machine’s user’s manual for setup instructions.
Aviso de Precaución
Por favor de leer todos los avisos de precaución como medida preventiva para el operador y el ACS
6000 console server.
IMPORTANTE: No hacer funcionar el ACS 6000 console server con la tapa abierta.
IMPORTANTE: Para prevenir un corto circuito en el ACS 6000 console server al desconectarlo de la red, primero desconectar el cable del equipo y luego el cable que conecta a la red. Para conectar el equipo a la red, primero conectar el cable a la red y luego al equipo.
IMPORTANTE: Asegurarse que el equipo este conectado a tierra, para prevenir un shock eléctrico. El cable eléctrico del equipo viene con tres clavijas para conectar asegurar conexión a tierra. No use adaptadores o quite la clavija de tierra. Si se tiene que utilizar una extensión, utilice una que tenga tres cables con clavija para conexión a tierra. Para proteger al ACS 6000 console server de fluctuaciones en corriente eléctrica, utilice una fuente eléctrica de respaldo. Asegurarse de que nada descanse sobre los cables del ACS 6000 console server, y que los cables no obstruyan el paso. Asegurarse de no dejar caer alimentos o bebidas en el Cyclades ACS
6000 Advanced Console Server Installation/Administration/User Guide. Si esto ocurre, avise a Avocent
Corporation.
IMPORTANTE: No empuje ningún tipo de objeto en los compartimientos del ACS 6000 console server. Hacer esto podría ocasionar un incendio o causar un corto circuito dentro del equipo.
IMPORTANTE: Mantenga el ACS 6000 console server fuera del alcancé de calentadores, y asegurarse de no tapar la ventilación del equipo.
Appendices 81
IMPORTANTE: El ACS 6000 console server con alimentación de corriente directa (CD) solo debe ser instalado en áreas con restricción y de acuerdo a los artículos 110-18, 110-26, y 110-27 del National Electrical Code,
ANSI/NFPA 701, Edición 1999. Para conectar la corriente directa (CD) al sistema, utilice cable de 0.75 mm (18
AWG). Instalar el interruptor corriente directa (CD) aprobado por UL entre la fuente de alimentación y el
Cyclades ACS 6000 advanced console server. El limite mínimo del interruptor deberá ser 2 amperes, con conductor de 0.75 mm (18 AWG).
Trabajar dentro del ACS 6000 console server
No intente dar servicio al ACS 6000 console server, solo que este bajo la dirección de Soporte
Técnico de Avocent. Si este es el caso, tome las siguientes precauciones:
Apague el ACS 6000 console server. Asegurase que este tocando tierra antes de tocar cualquier otra cosa, que puede ser al tocar la parte trasera del equipo.
Batería
IMPORTANTE: Una batería nueva puede explotar, si no esta instalada correctamente. Remplace la batería cuando sea necesario solo con el mismo tipo recomendado por el fabricante de la batería. Deshacerse de la batería de acuerdo a las instrucciones del fabricante de la batería.
82 Cyclades ACS 6000 Advanced Console Server Installation/Administration/User Guide
Appendix F: Technical Support
Our Technical Support staff is ready to assist you with any installation or operating issues you encounter with your Avocent product. If an issue should develop, follow the steps below for the fastest possible service.
To resolve an issue:
1.
Check the pertinent section of this manual to see if the issue can be resolved by following the procedures outlined.
2.
Visit www.avocent.com/support and use one of the following resources:
Search the knowledge base or use the online service request.
-or-
Select Technical Support Contacts to find the Avocent Technical Support location nearest you.
FCC Warning Statement
The Cyclades ACS advanced console server has been tested and found to comply with the limits for Class A digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the Installation and Service Manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user is required to correct the problem at his or her own expense.
Notice about FCC Compliance for All Cyclades ACS Advanced Console Server Models
To comply with FCC standards, the Cyclades ACS advanced console server requires the use of a shielded CAT
5 cable for the Ethernet interface. Notice that this cable is not supplied with either of the products and must be provided by the customer.
Canadian DOC Notice
The Cyclades ACS advanced console server does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
L’Cyclades ACS advanced console server n’émete pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le règlement sur le brouillage radioélectrique edicté par le Ministère des Communications du Canada.
Safety and EMC Approvals and Markings
FCC Class A (USA), CE Class A (EU), ICES-003 (Canada), VCCI (Japan), C-Tick (Australia), A-Tick (Australia, with internal modem), UL 60950-1 (USA), cUL (Canada), EN-60950-1 (EU), CB
For Technical Support: www.avocent.com/support
590-767-501C
Cyclades
®
ACS 6000
Installation/Administration/User Guide
Скачать
Общедоступная ссылка обновлена
Общедоступная ссылка на ваш чат была обновлена. Вы можете просматривать и управлять своими ссылками на чат после регистрации здесь.
Общедоступная ссылка на документ
Реклама
