AWA PCD-792 Instruction manual

AWA PCD-792 Instruction manual
PCD-792
MP3/CD/Radio
Audio System
INSTRUCTION MANUAL
Before use, please read the manual carefully.
WARNING
1. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or
moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall not be placed on apparatus.
2. WARNING: The battery (battery or batteries or battery pack) shall not be exposed to excessive heat
such as sunshine, fire or the like.
3. WARNING: Excessive sound pressure from earphones and headphones can cause hearing loss.
4. WARNING: The mains plug is used as disconnect device, the disconnect device shall remain
readily operable.
5. Do not install this equipment in a confined space such as a book case or similar unit.
The ventilation should not be impeded by covering the ventilation openings with items
such as newspaper, table-cloths, curtains etc.
6.
Invisible laser radiation when open and interlocks defeated. Avoid exposure to beam of laser.
7. No naked flame sources, such as lighted candles, should be placed on the apparatus.
8. Attention should be drawn to environmental aspects of battery disposal.
9. Use of the apparatus in moderate climates.
WARNING
TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING : SHOCK HAZARD-DO NOT OPEN
LIGHTNING FLASH WITH ARROWHEAD SYMBOL -
EXCLAMATION POINT - within an equilateral triangle,
within an equilateral triangle, is intended to alert the
is used to indicate that a specific component shall be
user to the presence of uninsulated dangerous
replaced only by the component specified in that
voltage within the products enclosure that may be of
documentation for safety reason.
sufficient magnitude to constitude a risk of electric
shock to persons.
The following label has been affixed to the unit, listing the proper procedure for working with the laser beam:
CLASS 1 LASER PRODUCT LABEL CLASS 1 LASER PRODUCT
KLASS 1 LASER APPARAT
LUOKEN 1 LAISERLAITE
KLASSE 1 LASER PRODUKT
This label is attached to the place as illustrated to inform that the
apparatus contains a laser component.
WARNING LABEL INFORMING OF RADIATION This label is placed inside the unit. As shown in the illustration. To
warn against further measures on the unit. The equipment contains
a laser radiating laser rays according to the limit of laser product of
class 1.
E-1
SAFETY INSTRUCTIONS
1. READ INSTRUCTIONS - All the safety and operating instructions should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instruction should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating instructions should be followed.
5. WATER AND MOISTURE - The appliance should not be used near water, for example, near a bathtub, washbowl,
kitchen sink, laundrytub, swimming pool or in a wet basement.
6. VENTILATION - The appliance should be situated so that its location or position does not interfere with its proper
ventilation. Do not place on bed, sofa, rug or similar surface that may block the ventilation openings, in a built-in
installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.
7. HEAT - The appliance should be situated away from heat sources such as radiators, stoves, or other appliances
(including amplifiers) that produce heat.
8. POWER SOURCE - The appliance should be connected to power supply only of the type described in the
operating instructions or as marked on the appliance.
9. GROUNDING - Precautions should be taken to ensure that the grounding means of an appliance is not defeated.
10. POWER CORD PROTECTION - Power supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them.
11. POWER LINES - An outdoor antenna should be located away from power lines.
12. OBJECT and LIQUID ENTRY - Care should be taken so that objects do not fall and liquids are not spilled into
the enclosure through openings.
13. ESD WARNING - The display does not function properly or no reaction to operation of any the control may due
to the electrostatic discharge. Switch off and unplug the set. Reconnect after a few seconds.
14. DAMAGE REQUIRING SERVICE - The appliance should be serviced by qualified service personnel when:
a. The power-supply cord or plug has been damaged.
b. Objects have fallen into, or liquid has been spilled into the appliance enclosure.
c. The appliance has been exposed to rain.
d. The appliance has been dropped, or the enclosure damaged.
e. The appliance does not appear to operate normally.
15. SERVICING - The user should not attempt to service the appliance beyond that described in the user operating
instructions. All other servicing should be referred to qualified service personnel.
Notes:
a. Dirty or scratched CD may cause a skipping problem. Clean or replace the CD.
b. If an error display or malfunction occurs, disconncet the AC cord and remove all the batteries. Then turn the power
back on.
BEFORE OPERATION
Notes: CONCERNING COMPACT DISCS.
Since dirty, damaged or warped discs may damage the appliance, care should be taken of the followings items:
a. Usable compact discs. Use only compact disc with the mark shown below.
b. CD compact disc only with digital audio signals.
E-2
LOCATION OF CONTROL
17
1
2
3
4
5
6
7
16
15
14
13
12
8
9 10 11
18
19
26
25
20
24
23
21
22
1. LCD DISPLAY
2. REMOTE SENSOR
3. STANDBY
4. TIME
5. HOUR
6. MINUTE
7. VOLUME 8. SKIP 9. SKIP +
10. STOP
11. PLAY / PAUSE
12. VOLUME +
13. MODE
14. PROGRAM
15. ALBUM +
16. EJECT
17. CD DOOR
18. FM ANTENNA
19. BAND SELECTOR
20. TUNING CONTROL
21. BATTERY BACKUP
22. AC CORD
23. PHONES JACK
24. AUX IN
25. BASS SELECTOR
26. FUNCTION SELECTOR
POWER SOURCE
AC POWER
You can power your appliance by plugging the AC power cord at the back of the appliance into a wall
AC power outlet. Check that the rated voltage of your appliance matches your local voltage.
E-3
REMOTE CONTROL
1. STANDBY
2. VOLUME 3. PLAY / PAUSE
4. SKIP 5. MODE
6. STOP
7. OPEN / CLOSE
8. VOLUME +
9. SKIP +
10. ALBUM +
1
7
2
3
8
4
9
5
10
6
BATTERY INSTALLATION
Insert 2 x “AAA” size batteries into the battery compartment. Be sure that the batteries are inserted
correctly to avoid damage to the remote control. Always remove the batteries when the remote
control will not be used for a long period of time, as this will cause leakage to the batteries a nd
subsequently damage to your set.
Notes:
- Use batteries of the same type. Never use different types of batteries together.
- If the distance required between the remote control and the appliance decreases, the batteries
are exhausted. In this case replace the batteries with new one.
SENSOR WINDOW OF THE RECEIVER
- Even if the remote control is operated within the effective range, its operation may be impossible if
there are any obstacies between the appliance and the remote control.
- If the remote control is operated near other appliances which generate infrared rays, or if other
remote control devices using infrared rays are used near the appliance, it may operate incorrectly.
E-4
RADIO OPERATION
GENERAL OPERATION
1.
2.
3.
4.
Set the “FUNCTION” selector to “RADIO” mode.
Select desired band by using the “BAND” selector.
Adjust radio frequency to your desired station by using the “TUNING” control.
Adjust the “VOLUME” control to the desired level.
FM / FM-STEREO RECEPTION
- Set the “BAND” selector to FM mode for MONO reception.
- Set the “BAND” selector to FM ST. mode for FM STEREO reception. The Stereo indicator light up
to show FM ST. mode.
FOR BETTER RECEPTION
FM - This appliance has a FM antenna located at the rear cabinet. This wire is completely unraveled
and extended for better reception.
AM - This appliance is equipped with a built - in directional ferrite AM antenna. Rotate the appliance
to get better reception.
E-5
CD / MP3 OPERATION
GENERAL OPERATION
PLAY / PAUSE
Press to start playing CD / MP3 disc.
Press again to stop playing CD / MP3 operation temporarily.
Press again to resume playback.
SKIP +
SKIP -
Press to go to the next track or back to the previous track.
Press and hold while playing until you find the point of the sound.
&
STOP
Press to stop all CD / MP3 operation.
EJECT
Press to open / close the CD door.
PLAYBACK
1.
2.
3.
4.
5.
6.
7.
8.
Set the “FUNCTION” selector to “CD” mode.
Open the CD door and place a CD / MP3 disc with the label up in the CD compartment.
Close the CD door.
Focus search is performed if disc is inside. Total number of tracks is read and appears on the
display.
Playbak will start automatically from the first track.
Adjust the “VOLUME” control to the desired level.
Press the “PLAY / PAUSE” button again when you want to stop temporarily.
Press the “STOP” button when finished.
E-6
CD / MP3 OPERATION
PROGRAM
Be sure to press the “STOP” button before use.
1. Press the “PROGRAM” button, the display will show “P01” and flash.
2. Select desired track by using the “SKIP +” or “SKIP -” button. ( You may select a desired album by
pressing “ALBUM +” button. )
3. Press the “PROGRAM” button again to confirm desired track into the program memory.
4. Repeat step 2 and 3 to enter additional tracks into the program memory.
5. When all the desired tracks have been programmed, press the “PLAY / PAUSE” button to
play the disc in the order you have programmed.
6. Press the “STOP” button twice to terminate programmed playback.
MODE
Press the “MODE” button during playing CD / MP3 disc,
each press switches the mode function as follows:
1 - REPEAT 1
2 - REPEAT ALBUM ( *MP3 ONLY )
3 - REPEAT ALL
4 - RANDOM
5 - NORMAL PLAYBACK
REP
REP
ALBUM
REP
ALL
REPEAT 1
REPEAT
ALBUM
REPEAT
ALL
RAND
NORMAL
PLAYBACK
E-7
RANDOM
OTHER FEATURES
CLOCK SETTING
To adjust clock setting, make sure not in radio mode.
1. Press the “TIME SET” button. (Do not release “TIME SET” button during time setting)
2. Press the “HOUR” button to set hour.
3. Press the “MIN” button to set minute.
4. Release all button to confirm setting. Confirmed setting will on the display.
E-8
CARE AND MAINTENANCE
COMPACT DISCS
Treat compact discs carefully. Handle them only by their edges. Never allow your fingers to touch the
shiny, unlabelled side of the disc.
Do not put adhesive tape, stickers etc. on either side of a disc.
Clean discs periodically with soft, lint-free, dry cloth. Never use detergents or abrasive cleaners to clean
discs. If necessary, use a CD cleaning kit.
If a disc skips or gets stuck during playback it is probably dirty or damaged (scratched).
When cleaning a disc, wipe in straight lines from the centre of the disc to its edge. Never wipe in circular
motions.
When removing a disc from its storage case, press down on the centre of the case and lift the disc out,
holding it carefully by its edges.
Fingerprints and dust should be carefully wiped off the disc’s recorded side with a soft cloth. Unlike
conventional records, compact discs have no grooves to collect dust, so gently wiping with a piece of
soft cloth should remove most particles.
CLEANING THE UNIT
To prevent fire or electric shock hazard, ensure that the unit is unplugged from the AC power supply
when cleaning it.
If the unit’s casing gets dusty, wipe it clean with a soft, dry dust cloth. Do not use any wax or polish
sprays on the unit.
If the unit’s casing gets dirty or smudged with fingerprints it can be cleaned with a soft cloth,
slightly damp with a mild soap and water. Never use abrasive cloths or polishes as these can
damage the casing.
CAUTION:
Never allow any water or other liquids to get inside the unit while cleaning.
E-9
TROUBLESHOOTING GUIDE
If you have a problem, please check the following chart to see if you can fix it before consulting a
servicing professional.
Symptom
Possible Cause
Radio
Noise or sound is distorted Channel is not tuned properly
on AM or FM broadcasts
for AM or FM
FM: The FM antenna wire is not
extended
AM : The built-in ferrite bar
antenna is not positioned
correctly
FM STEREO indicator
Band in mono mode
does not light up
You have tuned to a mono
station
The station signal is too weak
No sound in AM or FM
The unit is not in TUNER mode
CD Player
CD player does not play
CD skips while playing
Volume is at the minimum
position
The unit is not in CD mode
CD is not placed or placed
incorrectly
Disc is dirty or scratched
Solution
Fine tune the AM or FM broadcast
station
Extend the FM wire antenna fully
Reposition/rotate the unit until the best
reception is obtained
Press ST/MO button to enter STEREO
mode
Retune to another FM station
Retune to another FM station
Press TUNER / BAND button to enter
TUNER mode
Adjust the volume level
Press “CD” button to enter CD mode
Load disc with unlabelled side facing
downwards
Clean disc with cloth or use another
disc
RESETTING THE UNIT
If the system does not respond, you may have experienced a severe electric shock or a power surge
that triggered the internal computer to automatically shut down. If this occurs, disconnect the unit from
the AC power outlet and reconnect it again after a few seconds.
E-10
SPECIFICATIONS
GENERAL
Power source ---------------------------------- AC ~240V 50Hz
Remote control---------------------------------- DC 3V(1.5V x 2 “AAA” SIZE) not included
Power Consumption ------------------------ 21 W
Dimension ------------------------------------- Main Unit: 400(W) x 254(H) x 121(D) mm
TUNER
Frequency range ----------------------------AUDIO
Power Output --------------------------------Speaker impedance ------------------------Headphone impedance --------------------AUX input level ------------------------------ACCESSORIES
Instruction Manual --------------------------Remote Control---------------------------------
FM: 88 – 108 MHz
AM: 540 – 1620 KHz
2 Watts x 2
4 ohms
32 ohms
350 mV ~ 500mV
1 pc
1 pc
E-11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement