KOBE Brand Range Hood
KOBE Brand Range Hood
CH-100 Series (18” Height)
Model No.:
CH0030SQB-1 (30”)
CH0036SQB-1 (36”)
CH0042SQB-1 (42”)
CH0048SQB-1 (48”)
RA-02 Series (18” Height)
Model No.:
RA0230SQB-1 (30”)
RA0236SQB-1 (36”)
RA0242SQB-1 (42”)
RA0248SQB-1 (48”)
INSTALLATION INSTRUCTIONS
AND OPERATION MANUAL
IMPORTANT
READ THIS
FIRST
READ BEFORE INSTALLATION
1. Carefully check all contents of packages; 2. Thoroughly inspect the unit for any cosmetic damages or defects; 3. Test the unit before installation; 4. Have a certified contractor/electrician do the installation. IF THERE IS ANY PROBLEM:
1. DO NOT INSTALL THE UNIT AND KEEP ALL ORIGINAL PACKAGING MATERIAL. 2. Have your original proof of purchase and product serial number ready. 3. Call 1‐877‐BUY‐KOBE (289‐5623); or e‐mail to [email protected] to report the problem. NO RETURN, NO REFUND, NO EXCHANGE IF:
1. PRODUCT HAS BEEN INSTALLED 2. KNOCK‐OUT HOLES HAVE BEEN PUNCTURED 3. MISSING ORIGINAL PACKAGING MATERIAL AND/OR PARTS 1
- READ AND SAVE THESE INSTRUCTIONS -
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ...................................................................................... 3 COMPONENTS OF PACKAGE .................................................................................................... 5 INSTALLATION ............................................................................................................................. 7 OPERATION INSTRUCTIONS ................................................................................................... 17 MAINTENANCE .......................................................................................................................... 18 SPECIFICATIONS ...................................................................................................................... 19 MEASUREMENTS & DIAGRAMS .............................................................................................. 21 PARTS LIST ................................................................................................................................ 24 CIRCUIT DIAGRAM .................................................................................................................... 30 TROUBLE SHOOTING ............................................................................................................... 31 WARRANTY................................................................................................................................ 32 PRODUCT REGISTRATION....................................................................................................... 34 - READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN ACCORDANCE WITH
NATIONAL AND LOCAL ELECTRICAL CODES.
2
IMPORTANT SAFETY INSTRUCTIONS
- PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION -
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, OBSERVE THE FOLLOWING:
1) Installation and electrical wiring must be done by qualified professionals and in accordance with all
applicable codes and standards, including fire-rated construction.
2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden
utilities.
3) Ducted fans must be vented to the outside.
a) Before servicing or cleaning unit, open the light panel and SWITCH POWER OFF AT SERVICE
PANEL.
b) Clean all grease laden surfaces frequently. To reduce the risk of fire and to disperse air
properly, make sure to vent air outside. DO NOT vent exhaust air into wall spaces, attics, crawl
spaces or garages.
NOTE
-
This warranty is invalid without an authorized agent’s receipt or if unit is
damaged due to misuse, poor installation, improper use, mistreatment,
negligence or any other circumstances beyond the control of KOBE
RANGE HOODS authorized agents. Any repair carried out without the
supervision of KOBE RANGE HOODS authorized agents will
automatically void the warranty.
-
KOBE RANGE HOODS will not be held responsible for any damages to
personal property or real estate or any bodily injuries whether caused
directly or indirectly by the range hood.
WARNING:
TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE
TOP GREASE FIRE:
1. Keep all fan, baffle/spacer/filter/oil tunnel/oil container and grease-laden surfaces clean. Grease
should not be allowed to accumulate on fan, baffle/spacer/filter/oil tunnel/oil container.
2. Always turn hood ON when cooking.
3. Use high settings on cooking range ONLY when necessary.
4. Do not leave cooking range unattended when cooking.
5. Always use cookware and utensils appropriate for the type and amount of food prepared.
6. Use this unit only in the manner intended by the manufacturer.
7. Before servicing, switch power off at service panel and lock service panel (if possible) to prevent
power from switching on accidentally.
8. Clean ventilating fan frequently.
3
What to Do In The Event Of a Range Top Grease Fire
•
•
•
•
SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner.
KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not
go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911.
NEVER PICK UP A BURNING PAN – You May Get Burned.
DO NOT USE WATER, including wet dishcloths or towels – a violent steam blast will result.
Use an extinguisher ONLY if:
a) You have a Class A, B, C extinguisher and know how to operate it.
b) The fire is small and contained in the area where it started.
c) The fire department has been called.
d) You can fight the fire with your back to an exit.
What to Do If You Smell Gas
-
Extinguish any open flame.
Do not try to turn on the lights or any type of appliance.
Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and
Fire Department right away.
CAUTION
1) For general ventilation use only. Do not use to exhaust hazardous or explosive materials and
vapors.
2) To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustion
and exhausting of gases through the flue (chimney) to prevent back drafting.
3) Follow the heating equipment manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities.
4) Activating any switch on may cause ignition or an explosion.
5) Due to the size and weight of this hood, two people installation is recommended.
ELECTRICAL SHOCK HAZARD – Can result in serious injury or death.
Disconnect appliance from electric power before servicing. If equipped,
the fluorescent light bulb contains small amounts of mercury, which
must be recycled or disposed of according to Local, State, and Federal
Codes.
4
COMPONENTS OF PACKAGE
(Must keep all material for returns or refunds)
CH-100 Series
RANGE HOOD BOX
{A} KOBE Range Hood – 1
{B} Warranty Registration Card –1
{C} Instructions Manual – 1
{D} Oil Tunnel – 1
{E} Baffle Filter
- 2 (30” & 36”)
- 3 (42” & 48”)
{F} Spacer – 2
{G} 8” Round Exhaust Plate – 1
{H}
(42” & 48” only)
{H}
{I}
{J}
Screws Package – 1
Hood-Mounting Bracket – 2
Screws Package – 1
{I}
{J}
{A}
Duct Cover
(Sold Separately)
Option Of:
Model No. CH0030DC-12 for 30'' hood
KOBE Duct Cover – 1
Screw Package for Duct Cover – 1
{B}
{C}
Model No. CH0036DC-12 for 36'' hood
KOBE Duct Cover – 1
Screw Package for Duct Cover – 1
Model No. CH0042DC-12 for 42'' hood
KOBE Duct Cover – 1
Screw Package for Duct Cover – 1
{D}
{E}
{F}
{G}
Model No. CH0048DC-12 for 48'' hood
KOBE Duct Cover – 1
Screw Package for Duct Cover – 1
5
RA-02 Series
RANGE HOOD BOX
(BOX 1 OF 2)
{A} KOBE Range Hood – 1
{B} Warranty Registration Card –1
{C} Instructions Manual – 1
{D} Oil Tunnel – 1
{E} Baffle Filter
2 (30” & 36”)
3 (42” & 48”)
{F} Spacer – 2
{G} 8” Round Exhaust Plate – 1
{F}
{G}
{H}
(42” & 48” only)
{H} Screws Package – 1
{I} Hood-Mounting Bracket – 1
{J} Screws Package – 1
{A}
{I}
{B}
{J}
{C}
BOX 2 OF 2
ITEM NO.: RA02DC
{K}
{D}
Duct Cover
{E}
{K}
-
FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE www.KOBERangeHoods.com OR
CONTACT KOBE RANGE HOODS AT (626) 775-8880.
6
INSTALLATION
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING
Calculation before Installation
Calculate the length of the installation, before installing the hood. (All calculation is measure in inches.)
- FOR UNDER THE CABINET TABLE 1
CH-100 Series
A = Height of Floor to Ceiling
B = Height of Floor to Counter Top
(Standard: 36”)
C = Preferred Height of Counter Top to Hood
Bottom
30” & 36” Hood (Recommended 27” to 30”)
42” & 48” Hood (Recommended 30” to 36”)
D = Height of Hood
E = Height of the Cabinet
- FOR STAND ALONE TABLE 2
CH-100 Series
A = Height of Floor to Ceiling
B = Height of Floor to Counter Top
(Standard: 36”)
C = Preferred Height of Counter Top to Hood
Bottom
30” & 36” Hood (Recommended 27” to 30”)
42” & 48” Hood (Recommended 30” to 36”)
[(A – B] – (D + E)]
D = Height of Hood
E = Height of Duct Cover
7
RA-02 Series
SAFETY WARNING
HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS
NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING.
NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD
MAY OCCUR.
CH-100 SERIES – UNDER THE CABINET INSTALLATION ................................................................... 9 CH-100 SERIES – STAND ALONE INSTALLATION ............................................................................. 11 RA-02 SERIES - INSTALLATION ........................................................................................................... 14 8
CH-100 SERIES – UNDER THE CABINET INSTALLATION
Figure 1
Preparation before Installation
NOTE:







TO AVOID DAMAGE TO YOUR HOOD,
PREVENT DEBRIS FROM ENTERING
THE VENT OPENING.
Decide the location of the venting pipe from the
hood to the outside. Refer to Figure 1.
A straight, short venting run will allow the hood
to perform more efficiently.
Try to avoid as many transitions, elbows, and
long run as possible. This may reduce the
performance of the hood.
Temporarily wire the hood to test for proper
operation before installing.
Important: Peel protective film off the hood
(if any).
For installing under the cabinet with recessed
bottom, attach 4-inch wide wood filler strips (not
included) on each side. Refer to Figure 2.
Measure and create access opening for
electrical wires under the cabinet.
Figure 2
Hood Installation
CAUTION: If required to move the cooking
range to install the hood, turn off the power on
an electric range at the main electrical box.
SHUT OFF THE GAS BEFORE MOVING A GAS
RANGE.
Figure 3
1. Puncture the knockout holes on the hood as
shown in Figure 3.
2. (This step only applies to 42” and 48”
models.) Attach exhaust plate on hood with
four (3/16” x 3/8”) screws (included). Shown
in Figure 4.
3. Using
references
on
Table
1
and
measurements on page 21 center the hood in
place beneath the cabinet and flush with the
front of the cabinet.
4. Draw electrical wires through cabinet access
opening. Refer to Figure 6.
5. From the bottom of the hood, place screw (not
provided) into the exact center of each
knockout hole. Make sure all screws are in
place before tightening screws. CAUTION:
MAKE SURE THE HOOD IS SECURE
BEFORE RELEASING.
6. For safety purpose, pre-drilled mounting holes
are provided through the back of the hood. For
a more secure installation, use as many
mounting holes as needed to secure from the
inside of hood (screws not included).
Figure 4
9
Figure 5
Ductwork Installation
7. Use 6” round steel pipe for 30” and 36”
models or 8” round steel pipe for 42” and 48”
models (follow building codes in your area) to
connect the exhaust on the hood to the
ductwork above. Use duct tape to make all
joints secure and air tight. Refer to Figure 5.
Wiring to Power Supply
SAFETY WARNING
RISK OF ELECTRICAL SHOCK. THIS RANGE
HOOD MUST BE PROPERLY GROUNDED.
MAKE SURE THIS IS DONE BY SPECIALIZED
ELECTRICIAN IN ACCORDANCE WITH ALL
APPLICABLE
NATIONAL
AND
LOCAL
ELECTRICAL CODES. BEFORE CONNECTING
WIRES, SWITCH POWER OFF AT SERVICE
PANEL AND LOCK SERVICE PANEL TO
PREVENT POWER FROM BEING SWITCHED
ON ACCIDENTALLY.
8. Connect the electrical wires.
- Connect three wires (black, white and
green) to house wires and cap with wire
connectors. Connect according to color:
black to black, white to white, and green to
green as shown on Figure 6.
- If necessary to hide the electrical wire
connections, push wires back into the
wiring box. Access the wire connections
underneath the hood. To prevent any
damage, make sure wires do not slip
between motor or any moving parts.
Figure 6
Figure 7
Install Accessories
9. Attach Oil Tunnel. Refer to Figure 7.
10. Refer to Figure 8. c Slide the baffle filter into
the hood. d Push the baffle filter upward. e
Slide forward. f Pull downward. g Fit into
place.
11. Repeat until all baffle filters and spacers are
resting against oil tunnel. Refer to page 22.
Final Assembly
12. Turn power ON in control panel. Check all
lights and fan operation.
13. Make sure to leave this manual for the
homeowner.
10
Figure 8
CH-100 SERIES – STAND ALONE INSTALLATION
***This installation only applies with the purchase
of an optional duct cover:
Figure 9
Preparation before Installation
NOTE:







TO AVOID DAMAGE TO YOUR HOOD,
PREVENT DEBRIS FROM ENTERING
THE VENT OPENING.
Decide the location of the venting pipe from the
hood to the outside. Refer to Figure 9.
A straight, short venting run will allow the hood
to perform more efficiently.
Try to avoid as many transitions, elbows, and
long run as possible. This may reduce the
performance of the hood.
Temporarily wire the hood to test for proper
operation before installing.
Important: Peel protective film off the hood
and the duct cover (if any).
If necessary, prepare back wall frame with
cross framing lumber for secure installation.
Using
references
on
Table
2
and
measurements on page 21-22, decide the level
of the lumber. Refer to Figure 10.
Figure 10
Hood Installation
CAUTION: If required to move the cooking
range to install the hood, turn off the power on
an electric range at the main electrical box.
SHUT OFF THE GAS BEFORE MOVING A GAS
RANGE.
1. (This step only applies to 42” and 48” models.)
Attach exhaust plate on hood with four (3/16” x
3/8”) screws (included). Shown in Figure 11.
2. If necessary, remove the rubber stand on the
back of the hood.
3. Use twelve (3/16” x 3/8”) screws (included) to
attach the two hood-mounting brackets
(included) to the top of the hood.
4. Using references in Table 2 and Measurements
and Diagrams on pages 21-22, mark the
leveling point of the hood.
Position six
mounting screws (not included) on the wall,
leaving 1/8” away from the wall.
11
Figure 11
5. Align hood-mounting bracket to the six screws
on the wall and hook hood into place. Tighten
screws to secure hood to the wall.
6. For safety purpose, pre-drilled mounting holes
are provided through the back of the hood. For
a more secure installation, use as many
mounting holes as needed to secure from the
inside of hood (screws not included).
CAUTION: MAKE SURE HOOD
SECURE BEFORE RELEASING.
Figure 12
IS
Wiring to Power Supply
SAFETY WARNING
RISK OF ELECTRICAL SHOCK. THIS RANGE
HOOD MUST BE PROPERLY GROUNDED.
MAKE SURE THIS IS DONE BY SPECIALIZED
ELECTRICIAN IN ACCORDANCE WITH ALL
APPLICABLE
NATIONAL
AND
LOCAL
ELECTRICAL CODES. BEFORE CONNECTING
WIRES, SWITCH POWER OFF AT SERVICE
PANEL AND LOCK SERVICE PANEL TO
PREVENT
POWER FROM BEING SWITCHED ON
ACCIDENTALLY.
7. Connect the electrical wires.
- Connect three wires (black, white and
green) to house wires and cap with wire
connectors. Connect according to color:
black to black, white to white, and green to
green as shown on Figure 12.
- If necessary to hide the electrical wire
connections, push wires back into the
wiring box. Access the wire connections
underneath the hood. To prevent any
damage, make sure wires do not slip
between motor or any moving parts.
12
Figure 13
Duct Cover Installation
8. Use 6” round steel pipe for 30” and 36” models
or 8” round steel pipe for 42” and 48” models
(follow building codes in your area) to connect
the exhaust on the hood to the ductwork
above. Use duct tape to make all joints secure
and air tight. Refer Figure 13. Slide the duct
cover onto the hood.
9. Use 3/16” x 3/8” screws (included) to attach
duct cover to hood.
Figure 14
Install Accessories
10. Attach oil tunnel. Refer to Figure 14.
11. Refer to Figure 15. c Slide the baffle filter into
the hood. d Push the baffle filter upward. e
Slide forward. f Pull downward. g Fit into
place.
12. Repeat until all baffle filters and spacers are
resting against oil tunnel. Refer to page 20.
Final Assembly
13. Turn power ON in control panel. Check all
lights and fan operation.
14. Make sure to leave this manual for the
homeowner.
13
Figure 15
RA-02 SERIES - INSTALLATION
Figure 17
Preparation before Installation
NOTE:








TO AVOID DAMAGE TO YOUR HOOD,
PREVENT DEBRIS FROM ENTERING
THE VENT OPENING.
Decide the location of the venting pipe from the
hood to the outside. (Figure 16)
A straight, short venting run will allow the hood
to perform more efficiently.
Try to avoid as many transitions, elbows, and
long run as possible. This may reduce the
performance of the hood.
Temporarily wire the hood to test for proper
operation before installing
Important: Peel protective film off the hood
and the duct cover (if any).
If necessary, prepare back wall frame with cross
framing lumber for secure installation. Refer to
Table 2 and measurements on Page 23 to
decide the level of the lumber. (Figure 17)
Loosen hood-mounting brackets at the back of
the hood, adjust brackets and tighten screws.
If necessary, remove the rubber stand on the
back of the hood. (Figure 18)
Figure 16
14
Figure 18
Figure 19
Hood Installation
CAUTION: If required to move the cooking
range to install the hood, turn off the
power on an electric range at the main
electrical box.
SHUT OFF THE GAS
BEFORE MOVING A GAS RANGE.
1. Using references in Table 2 and measurements
on Page 23, mark the leveling locations point for
hood-mounting bracket on the wall.
2. Secure two mounting screws (not provided) to
the wall, leaving an 1/8” space from the wall.
3. Align the hood-mounting bracket to the
mounting screws on the wall and hang hood into
place.
4. Secure and tighten the mounting screws.
Figure 20
CAUTION: MAKE SURE HOOD IS SECURE
BEFORE RELEASING.
Wiring to Power Supply
SAFETY WARNING
RISK OF ELECTRICAL SHOCK. THIS RANGE
HOOD MUST BE PROPERLY GROUNDED.
MAKE SURE THIS IS DONE BY SPECIALIZED
ELECTRICIAN IN ACCORDANCE WITH ALL
APPLICABLE
NATIONAL
AND
LOCAL
ELECTRICAL CODES. BEFORE CONNECTING
WIRES, SWITCH POWER OFF AT SERVICE
PANEL AND LOCK SERVICE PANEL TO
PREVENT POWER FROM BEING SWITCHED ON
ACCIDENTALLY.
5. Connect the electrical wires.
- Connect three wires (black, white and
green) to house wires and cap with wire
connectors. Connect according to color:
black to black, white to white, and green to
green as shown on Figure 19.
- If necessary to hide the electrical wire
connections, push wires back into the wiring
box.
Access the wire connections
underneath the hood. To prevent any
damage, make sure wires do not slip
between motor or any moving parts.
15
Figure 21
Figure 22
Duct Cover Installation
6. Use 6” round steel pipe for 30” and 36” models
or 8” round steel pipe for 42” and 48” models
(follow building codes in your area) to connect
the exhaust on the hood to the ductwork above.
Use duct tape to make all joints secure and air
tight. Refer Figure 20.
7. Use four 4mm x 8mm screws (included) to attach
duct cover to hood. Refer to Figure 21.
Install Accessories
8. Attach oil tunnel. Refer to Figure 22.
9. Refer to Figure 23. c Slide the baffle filter into
the hood. d Push the baffle filter upward. e
Slide forward. f Pull downward. g Fit into
place.
10. Repeat until all baffle filters and spacers are
resting against oil tunnel. Refer to page 23.
Final Assembly
11. Turn power ON in control panel. Check all lights
and fan operation.
12. Make sure to leave this manual for the
homeowner.
16
Figure 23
OPERATION INSTRUCTIONS
This KOBE hood is equipped with two rotary controls with powerful centrifugal squirrel cage, baffle
filters, and bright LED lights.
The two rotary controls are Light Control & Speed Control. Refer to Figure 28.
Figure 28
Note: For best results, turn hood to QuietMode™ prior to preparation or cooking to establish
airflow in the kitchen. Adjust speed as needed.
•
Rotate the Speed Control clockwise to cycle from QuietMode™, Low, High, and Off;
and rotate counterclockwise to cycle from High, Low, QuietMode™, and off
•
Rotate the Light Control clockwise to turn on the light.
17
MAINTENANCE
For the optimal level of operation, clean the range hood surface and baffles regularly.
To Clean Hood Surface
CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS.
*** Regular care will help preserve its fine appearance.
1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth.
2. If hood looks splotchy (stainless steel hood), use an orange base cleaner to clean the surface of
the hood. Avoid cleaner to get on the control switches. Only spread a light coating over the
surface of the hood and leave on for a few minutes (do not leave on too long or this may cause
damage to hood finish). Use soft towel to wipe off the cleaning solution, gently rubs any
stubborn spots. Use a slightly damp towel to get rid of any cleaning solution. Use dry soft towel
to dry the hood.
3. To bring the glow back into a stainless steel finish, use a stainless steel cleaner.
4. DO NOT allow deposits to remain for long periods of time.
5. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface
causing rust.
6. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in
contact with stainless steel for extended periods. Many of these compounds contain chemicals,
which may be harmful. Rinse with water after exposure and wipe dry with a clean cloth.
To Clean Baffle Filters & Oil Tunnel
CAUTION: DRAIN BAFFLE FILTERS AND OIL TUNNEL BEFORE OIL WILL OVERFLOW.
1. Remove the baffle filters and oil tunnel.
2. Using a sponge, wash with warm soapy water. Dry completely before returning into place.
(Note: Baffle Filters are top rack dishwasher safe.)
18
SPECIFICATIONS
CH-100 Series
MODEL / SIZE
CH0030SQB-1 / 30” / Single Blower
CH0036SQB-1 / 36" / Single Blower
CH0042SQB-1 / 42” / Dual Blowers
CH0048SQB-1 / 48” / Dual Blowers
COLOR
Commercial Grade Stainless Steel
CONSUMPTION / AMPERE
CH0030SQB-1 – 320W / 2.86A
CH0036SQB-1 – 320W / 2.86A
CH0042SQB-1 – 350W / 3A
CH0048SQB-1 – 350W / 3A
VOLTAGE
120V 60Hz
NUMBER OF BLOWER
1 – 30”, 36”
2 – 42”, 48”
DESIGN
18-Gauge Seamless / Satin Finish
FAN TYPE: CENTRIFUGAL
Squirrel Cage
EXHAUST
Top 6” Round – 30”, 36”
Top 8” Round – 42”, 48”
CONTROLS
Rotary Switch
LIGHTS
3-Watt LED x 2 – 30”, 36”
3-Watt LED x 3 – 42”, 48”
HOOD DIMENSION
(W x D x H)
(CH0030SQB-1)
(CH0036SQB-1)
(CH0042SQB-1)
(CH0048SQB-1)
OPTIONAL ACCESSORIES
(W x D x H)
1) Duct Cover:
Model No. CH0030DC-12 (30” x 12” x 12”)
Model No. CH0036DC-12 (36” x 12” x 12”)
Model No. CH0042DC-12 (42” x 12” x 12”)
Model No. CH0048DC-12 (48” x 12” x 12”)
2) Model No. SSP30
30” Stainless Steel Back Panel (30” x 1/10” x 32”)
3) Model No. SSP36
36” Stainless Steel Back Panel (36” x 1/10” x 32”)
(CH0030SQB-1)
(CH0036SQB-1)
(CH0042SQB-1)
(CH0048SQB-1)
Net
70
75
108
112
Gross
85
93
128
135
QuietMode™
Low
High
Air Capacity (cfm)
Sone*
300
1.8
580
4.7
760
5.4
Air Capacity (cfm)
Sone*
450
2.5
800
6.0
1200
8.0
HOOD WEIGHT (lbs)
SPEED
SINGLE BLOWER
CH0030SQB-1
CH0036SQB-1
DUAL BLOWERS
CH0042SQB-1
CH0048SQB-1
29-3/4” x 24” x 18”
35-3/4” x 24” x 18”
41-3/4” x 24” x 18”
47-3/4” x 24” x 18”
*One sone is equivalent to the sound of a refrigerator at 40 decibels.
**Specifications subject to change without notice.
19
RA-02 Series
MODEL / SIZE
RA0230SQB-1 / 30” / Single Blower
RA0236SQB-1 / 36" / Single Blower
RA0242SQB-1 / 42” / Dual Blowers
RA0248SQB-1 / 48” / Dual Blowers
COLOR
Commercial Grade Stainless Steel
CONSUMPTION / AMPERE
RA0230SQB-1 – 320W / 2.86A
RA0236SQB-1 – 320W / 2.86A
RA0242SQB-1 – 350W / 3A
RA0248SQB-1 – 350W / 3A
VOLTAGE
120V 60Hz
NUMBER OF BLOWER
1 – 30”, 36”
2 – 42”, 48”
DESIGN
18-Gauge Seamless / Satin Finish
FAN TYPE: CENTRIFUGAL
Squirrel Cage
EXHAUST
Top 6” Round – 30”, 36”
Top 8” Round – 42”, 48”
CONTROLS
Rotary Switch
LIGHTS
3-Watt LED x 2 – 30”, 36”
3-Watt LED x 3 – 42”, 48”
HOOD DIMENSION
(W x D x H)
(RA0230SQB-1)
(RA0236SQB-1)
(RA0242SQB-1)
(RA0248SQB-1)
OPTIONAL ACCESSORIES
(W x D x H)
1) Model No. RA02DC-24
1-Piece Extension Duct Cover (15” x 12” x 24-1/2”)
2) Model No. SSP30
30” Stainless Steel Back Panel (30” x 1/10” x 32”)
3) Model No. SSP36
36” Stainless Steel Back Panel (36” x 1/10” x 32”)
Net
Gross
(RA0230SQB-1)
(RA0236SQB-1)
(RA0242SQB-1)
(RA0248SQB-1)
RA02DC
46
53
65
72
66
73
87
94
5
7
QuietMode™
Low
High
Air Capacity (cfm)
Sone*
300
1.8
580
4.7
760
5.4
Air Capacity (cfm)
Sone*
450
2.5
800
6.0
1200
8.0
HOOD WEIGHT (lbs)
SPEED
SINGLE BLOWER
RA0230SQB-1
RA0236SQB-1
DUAL BLOWERS
RA0242SQB-1
RA0248SQB-1
29-3/4” x 24” x 18”
35-3/4” x 24” x 18”
41-3/4” x 24” x 18”
47-3/4” x 24” x 18”
*One sone is equivalent to the sound of a refrigerator at 40 decibels.
**Specifications subject to change without notice.
20
MEASUREMENTS & DIAGRAMS


All measurements in ( ) are millimeters.
All inch measurements are converted from millimeters. Inch measurements are
estimated.
CH-100 Series
MODEL NO.: CH0030SQB-1 (30”)
CH0036SQB-1 (36”)
CH0042SQB-1 (42”)
CH0048SQB-1 (48”)
- FOR UNDER THE CABINET -
- FOR STAND ALONE -
21
- FOR STAND ALONE (WITH OPTIONAL DUCT COVER) CH-100 Series
MODEL NO.: CH0030SQB-1 (30”)
CH0036SQB-1 (36”)
CH0042SQB-1 (42”)
CH0048SQB-1 (48”)
***Hood-Mounting Bracket
Baffle Filters & Stainless Steel Spacer
22
 All measurements in ( ) are millimeters.
 All inch measurements are converted from millimeters. Inch measurements are
estimated.
RA-02 Series
MODEL NO.: RA0230SQB-1 (30”)
RA0236SQB-1 (36”)
RA0242SQB-1 (42”)
RA0248SQB-1 (48”)
23
PARTS LIST
CH-100 Series
MODEL NO.: CH0030SQB-1 (30”)
CH0036SQB-1 (36”)
CH0042SQB-1 (42”)
CH0048SQB-1 (48”)
NO.
1
2
3
DESCRIPTION
Screw (3/16” x 3/8” )
Hood Mounting Bracket
6” Round Plastic Exhaust
8” Round Exhaust Plate
4
Air Chamber & Motor
5
LED Light
6
Metal Oil Tunnel
7
8
9
10
11
12
A
B
C
D
LED Driver
Capacitor
Valve Stem
Knob
Baffle Filter
Spacer
1-5/16” wide
4-5/16” wide
15/16” wide
3-7/8” wide
MODEL /SIZE
CH0030SQB-1 / CH0036SQB-1
CH0042SQB-1 / CH0048SQB-1
CH0030SQB-1 / CH0036SQB-1
CH0042SQB-1 / CH0048SQB-1
CH0030SQB-1
CH0036SQB-1
CH0042SQB-1
CH0048SQB-1
CH0030SQB-1
CH0036SQB-1
CH0042SQB-1
CH0048SQB-1
PART NO.
L1-0707-0002
L1-0221-1630
L1-0505-0001
L1-0242-3630
L1-0302-0120-802SS
L1-0302-0120-802S
L1-0403-0301
B101-9130-15
B101-9136-15
B101-9142-15
B101-9148-15
L1-0402-D001
L1-0401-0120-24
L1-0405-0404-B
L1-0405-0400-A
L1-0214-0191
B101-2130-09
B101-2136-09
B101-2142-09
B101-2148-09
(Optional Duct Cover)
ORIGINAL KIT
NO.
DESCRIPTION
01
Duct Cover
02
Screw (3/16” x 3/8”)
MODEL /SIZE
CH0030DC-12
CH0036DC-12
CH0042DC-12
CH0048DC-12
24
PART NO.
B102-0030-12
B102-0036-12
B102-0042-12
B102-0048-12
L1-0707-0002
CH-100 Series
MODEL NO.: CH0030SQB-1 (30”)
CH0036SQB-1 (36”)
25
CH-100 Series
MODEL NO.: CH0042SQB-1 (42”)
CH0048SQB-1 (48”)
26
RA-02 Series
MODEL NO.:
NO.
RA0230SQB-1 (30”)
RA0236SQB-1 (36”)
RA0242SQB-1 (42”)
RA0248SQB-1 (48”)
2
DESCRIPTION
6” Round Plastic Exhaust
8” Round Exhaust Plate
Duct Cover
3
Hood Mounting Bracket
4
5
6
7
8
LED Light
Valve Stem
Knob
Capacitor
LED Driver
9
Air Chamber & Motor
10
Oil Tunnel
11
12
A
B
C
D
Baffle Filter
Spacer
1-5/16” wide
4-5/16” wide
15/16” wide
3-7/8” wide
1
MODEL /SIZE
RA0230SQB-1 / RA0236SQB-1
RA0242SQB-1 / RA0248SQB-1
RA02DC
RA0230SQB-1 / RA0236SQB-1
RA0242SQB-1 / RA0248SQB-1
RA0230SQB-1 / RA0236SQB-1
RA0242SQB-1 / RA0248SQB-1
RA0230SQB-1
RA0236SQB-1
RA0242SQB-1
RA0248SQB-1
RA0230SQB-1
RA0236SQB-1
RA0242SQB-1
RA0248SQB-1
27
PART NO.
L1-0505-0001
L1-0242-3630
12-02000-012-61
L1-0201-0230
L1-0201-0242
L1-0403-0301
L1-0405-0404-B
L1-0405-0400-A
L1-0401-0120-24
L1-0402-D001
L1-0302-0120-802SS
L1-0302-0120-802S
B101-9130-14
B101-9136-14
B101-9142-14
B101-9148-14
L1-0214-0191
B101-9130-15
B101-9136-15
B101-9142-15
B101-9148-15
RA-02 Series
MODEL NO.:
RA0230SQB-1 (30”)
RA0236SQB-1 (36”)
28
RA-02 Series
MODEL NO.:
RA0242SQB-1 (42”)
RA0248SQB-1 (48”)
29
CIRCUIT DIAGRAM
CH-100 Series
MODEL NO.: CH0030SQB-1 (30”)
CH0036SQB-1 (36”)
CH0042SQB-1 (42”)
CH0048SQB-1 (48”)
RA-02 Series
MODEL NO.:
RA0230SQB-1 (30”)
RA0236SQB-1 (36”)
RA0242SQB-1 (42”)
RA0248SQB-1 (48”)
30
TROUBLE SHOOTING
Issue
After Installation,
both motors and
lights are not
working.
Possible Cause
The power is not on.
The wire connection is not secure.
The control panel is defective.
Solution
Make sure the circuit breaker and the unit’s power is
ON. Use a voltage meter to check the power supply.
Check and tighten wire connection.
Replace the control panel.
Lights are
working, but
motor(s) is not.
The motor(s) is defective.
The capacitor(s) is defective.
The control panel is defective.
Replace the motor.
Replace capacitor(s).
Replace the control panel.
The range
hood is
vibrating.
The blower system is not secure.
The motor is
working, but
the lights are
not working.
LED Light(s) is defective.
Tighten the turbine impeller/squirrel cage and air
chamber.
Replace the squirrel cage.
Check the installation of hood, tighten the
mounting bracket.
Replace the LED light.
The squirrel cage is not balanced.
Hood is not secured in place.
The light wiring(s) is loose.
Light transformer is defective.
The range
hood is not
venting out
correctly.
The control panel is defective.
The range hood is installed outside of
the manufacture recommended
clearance.
There is no make-up air inside the
house.
Obstacle blocking the pipe work.
The pipe size is smaller than the
suggested pipe size.
Cold air is
The pipe connection is not properly
coming into the sealed.
home.
The damper is not properly installed or
is missing from the installation.
The damper is not installed.
31
Check wire continuity from light transformer to
LED light housing(s).
Check power input and power output on the light
transformer. If it’s needed, replace the light
transformer.
Replace the control panel.
Adjust the clearance between the range hoods
and cook top to 27” to 30”. For Island range
hood, the clearance between the range hoods
and cook top is 30” to 36”.
Open the window to enhance the performance
of the range hood by creating a sufficient makeup air.
Remove all obstacles from the duct work.
Change the ducting according to the
manufacture suggestion.
Check the pipe installation.
Check the damper installation.
By installing the damper, it will help to eliminate
air backflow.
WARRANTY
WARRANTY CERTIFICATE
KOBE Range Hoods (referred to herein as “we” or “us”) warrants to the original purchaser (referred to
herein as “you” or “your”) all products manufactured or supplied by us to be free from defect in
workmanship and materials as follows:
TWO-YEAR LIMITED WARRANTY FOR PARTS AND LABOR ON KOBE PREMIUM SERIES:
For two years from the date of your original invoice from a KOBE authorized dealer, we will, at our sole
discretion, choose to repair or replace the product free of charge that failed due to manufacturing
defects.
It is your sole responsibility to ensure the product is readily accessible for the service technician to
perform repairs. The service technician will not, under any circumstance, remove, alter or modify
any fixture built around and/or connected to the product to gain access to perform repairs.
During the two-year Limited Warranty period, additional charges may apply which include but are not
limited to:
•
•
•
Service technician travel charges if the requested service location is 30-miles out of
KOBE’s authorized service area
Parts shipping expenses
Un-installation of defective product and Installation of replacement product
ONE-YEAR LIMITED WARRANTY FOR PARTS ON KOBE BRILLIA SERIES:
For one year from the date of your original invoice from a KOBE authorized dealer, we will provide, free
of charge, parts to replace those that failed due to manufacturing defects. It is our sole discretion to
choose to repair or replace defective parts. It is your sole responsibility for all labor costs associated
with this warranty.
Warranty Exclusions:
This warranty does not cover, including but not limited to the following:
a.
b.
c.
d.
e.
f.
g.
h.
i.
j.
k.
l.
m.
Improper installation.
Any repair, alteration, modification not authorized by KOBE.
Duct alteration, modification and connection.
Incorrect electric current, voltage or wiring.
Normal maintenance and service required for the product.
Consumable parts such as light bulbs and carbon filters.
Improper usage of the product that it is not intended for, such as commercial use,
outdoor use and multi-family use.
Normal wear and tear.
Chips, scratches or dents by abuse or misuse of the product.
Damages caused by accident, fire, flood and other Acts of God.
Expenses incurred for service located outside of the designated service area.
Purchases from unauthorized dealers.
Removal fees of defective product and Installation fees associated with replacement
product.
If we determine that the warranty exclusions listed above apply or if you fail to provide all necessary
documentation for warranty service, you will be responsible for all expenses associated with the
requested service, including parts, labor, shipping, travelling and any other expense related to the
service request.
32
To qualify for warranty service, you must:
1.
2.
3.
4.
5.
Have the ORIGINAL proof of purchase
Be the ORIGINAL purchaser of the product
Have the model number
Have the serial number
Have a description of the nature of any defect in the product or part
TO REQUEST WARRANTY SERVICE, PLEASE CONTACT THE KOBE RANGE HOODS SERVICE
CENTER:
KOBE SERVICE CENTER
Tel:
1-855-800-KOBE (5623)
E-mail: [email protected]
33
WARRANTY INFORMATION FORM
Fill in the blanks and keep this paper with the original invoice in a
safe place for future service purpose.
1. Date of purchase
:
2. Model No.
:
3. Serial No.
:
For warranty service or spare parts purchase contact:
KOBE Service Center
Toll Free: 1-855-800-KOBE (5623)
Email: [email protected]
To report a problem, please contact:
Toll Free: 1-877-BUY-KOBE (289-5623)
Email: [email protected]
For product information contact:
Toll free: 1-877-BUY-KOBE (289-5623)
Email: [email protected]
Your notes:
34
KOBE Range Hoods
11775 Clark Street
Arcadia, CA 91006 USA
http://www.KOBERangeHoods.com
This KOBE hood is made for use in the USA and CANADA only. We do not recommend
using this hood overseas as the power supply may not be compatible and may violate
the electrical code of that country. Using a KOBE hood overseas is at your own risk
and will void your warranty.
Information subject to change without notice.
VER.131008
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement