American Standard 6540145.002 Monterrey 8 in. Widespread 2-Handle 0.5 GPM Gooseneck Bath Faucet with Vandal Resistant Lever Handles in Polished Chrome Installation instructions

1

6500

6501

6502

6530

6531

6532

SPREAD LAVATORY

FAUCETS

Thank you for selecting American-Standard...

the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

CAUTION

Turn off water at main supply.

CONVENTIONAL SPOUT

CONVENTIONAL OR GN SPOUT ASSEMBLY

Insert SPOUT SHANK (1, 1a) through center hole of SINK, making sure

RUBBER GASKET (2, 2a) is properly positioned.

Assemble RUBBER WASHER (3),

RETAINER (4) and LOCKNUT (5) onto threads of SPOUT SHANK (1, 1a) from underside of SINK.

Align SPOUT and tighten LOCKNUT (5).

Be sure slot in BRASS WASHER (4) is positioned to the rear as shown.

Insert LIFT ROD (6, 6a) through SPOUT and slot of BRASS WASHER (4).

SINK

6

2

SLOT

1

3

4

5

GOOSE NECK

SPOUT (POP-UP)

6a

SINK

2a

SLOT

Certified to comply with ANSI A112.18.1

60186 REV.1.5 (2/15)

GOOSE NECK

SPOUT

1a

3

4

5

2

VALVE ASSEMBLY

Install LOCKNUTS (1), BRASS WASHERS (2) and RUBBER WASHERS (3) onto valve shanks.

Push TUBING (4) ends into VALVE (5) side outlets. Insert VALVES (5) into mounting holes from underside of ledge.

Press TEE (6) onto SPOUT SHANK (7) making certain that the O-RING (8) is properly seated on SHANK (7). Push COUPLING (9) into TEE (6) and attach to SPOUT SHANK (7) and tighten.

Place RUBBER RING (11) into DECK ADAPTERS (10) and thread onto valves until snug against internal stop.

Tighten LOCKNUT (1) to secure VALVE (5) position.

10

11

Slide FERRULE (13) and COUPLING NUT (14) to outlet of VALVE (5) and tighten

COUPLING NUT (14) firmly.

Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of right VALVE using appropriate connector.

3

5/16'' MIN.

11

5

10

2

1

HOT

5

13

14

MOUNTING SURFACE

3

2

1

4

6

9

10

11

MOUNTING

LEDGE

8

7

14

13

COLD

5

3

DRAIN INSTALLATION

(Models 6801 and 6831 only)

Push TAILPIECE (1) down into TRAP (2)

(threaded end up).

Thread LOCKNUT (3), WASHER (4) and

GASKET (5) onto DRAIN BODY (6).

SINK

Apply a bead of PUTTY to underside of FLANGE (7).

Feed DRAIN BODY (6) up through SINK and thread FLANGE (7) fully onto BODY (6).

7

Tighten LOCKNUT (3) firmly, keeping the

PIVOT ROD (8) pointed towards the back of the SINK.

Drop STOPPER (9) into DRAIN BODY (6).

3

6

Pull TAILPIECE (1) up and thread tightly into DRAIN BODY (6).

4

DRAIN ASSEMBLY (6542.140/.170)

Apply a bead of PUTTY around underside of DRAIN FLANGE (1) flange. Insert DRAIN

PLUG (2) into SINK drain hole.

PUTTY

Hold DRAIN PLUG (2) to prevent turning and assemble GASKET (3), WASHER (4), and

LOCKNUT (5) from underneath sink.

Apply sealant to threaded end of TAILPIECE and thread into lower end of DRAIN PLUG.

Connect other end to trap.

3

4

5

6

6

TEST INSTALLED FAUCET

Remove AERATOR.

With handle in OFF position, turn on water supplies and check all connections for leaks.

Operate both handles to flush water lines thoroughly. Check spout mounting and TEE connections for leaks.

Turn handles into OFF position and replace AERATOR.

9

PUTTY

5

4

Position EXTENSION ROD (10) onto POP-UP

ROD (11) and tighten THUMBSCREW (12).

Remove one end of CLIP (13) from PIVOT ROD (11) by squeezing ends together while sliding.

Insert PIVOT ROD (14) into second or third hole in EXTENSION (10) and reassemble CLIP (13).

(EXTENSION (10) may need to be bent.)

14

12

11

10

13 8

1

2

1

SINK

2

SEALANT

5

Adjust STOPPER (9) height by repositioning

EXTENSION (10) and tightening THUMBSCREW (12).

INSTALL HANDLES

7

6

2

Turn VALVES (1) to off position.

Insert ADAPTOR (8) with larger diameter over the VALVE STEM (4).

Align LEVER (2) or WRIST

BLADE HANDLE (3) and install onto VALVE STEM (4).

Insert BLUE INDEX (5) into cold valve (right side) and red

INDEX (6) into hot valve (left side).

Insert HANDLE SCREW (7) into

HANDLES and tighten with screwdriver.

8

4

1

7

5

3

AERATOR

7

SERVICE STOP

WASHER

90°

To change direction of handle rotation, proceed as follows:

Turn valve to OFF position.

Remove HANDLE and BONNET NUT.

Remove SPRING CLIP.

Lift STOP WASHER, turn 90° and replace.

Replace SPRING CLIP.

Replace BONNET NUT, HANDLE, SCREW, and INDEX.

SPRING

CLIP

AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean.

If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°.

Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow. To clean, first turn off hot and cold water supplies, then:

Remove HANDLE and BONNET NUT.

Remove CARTRIDGE by pulling up.

Thoroughly rinse plastic SCREEN at base of CARTRIDGE.

Replace CARTRIDGE until flange is tight against valve body.

Turn valves OFF.

SCREEN

Replace BONNET NUT, HANDLE, SCREW and INDEX.

CARTRIDGE

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A

CLOTH WITH A COARSE SURFACE.

60186 REV.1.5 (2/15)

912711-0070A

O-RING

A911748-0020A

SPOUT GASKET

030256-0070A

SPOUT

MOUNTING KIT

000690-0020A

HANDLE SCREW

051211-0070A

INDEX KIT (PAIR)

M918014-0070A

ADAPTER

051217-0020A

WRIST BLADE

HANDLE

904939-0020A

BONNET NUT

951764-0070A

CARTRIDGE

051212-0020A

ESCUTCHEON KIT

051213-0070A

VALVEMOUNTING KIT

012086-0020A

POP-UP ROD

M922880-0020A

AERATOR,

1.5gpm/5.7L/min.

066074-0070A

VR AERATOR,

0.5gpm/1.9L/min.

M922858-0020A

VR AERATOR,

0.35gpm/1.3L/min.

051210-0020A

LEVER HANDLE

051322-0020A

VANDAL PROOF SCREW

000690-0020A

HANDLE SCREW

051211-0070A

INDEX KIT

M918014-0070A

ADAPTER

028757-0070A

SPOUT GASKET

030256-0070A

SPOUT MOUNTING KIT

SPREAD LAVATORY

FAUCETS

MODEL NUMBERS

6500

6501

6502

6530

6531

6532

M922880-0020A

AERATOR, 1.5gpm/5.7L/min.

066074-0070A

VR AERATOR, 0.5gpm/1.9L/min.

M922858-0020A

VR AERATOR, 0.35gpm/1.3L/min.

912711-0070A

O-RING

A911748-0020A

SPOUT GASKET

015025-YYY0A

DRAIN COMPLETE

030256-0070A

SPOUT

MOUNTING KIT

070532-0040A

TAILPIECE

028617-0020A

POP-UP ROD

912711-0070A

O-RING

012683-0020A

CONVENTIONAL SPOUT

WITH POP-UP DRAIN

012683-0020A

CONVENTIONAL SPOUT

LESS DRAIN

M922881-0020A

AERATOR 1.5 GPM

066508-0020A

AERATOR 0.5VR GPM

M922286-0020A

AERATOR 0.35 GPM

066497-0020A

COMPLETE

DRAIN BODY

066116-YYY0A

DRAIN STOPPER

012112-0070A

TUBE SEAL &

COUPLING KIT

012111-0070A

TUBE & TEE KIT (8" CENTERS)

066064-0070A

TUBE & TEE KIT (12" CENTERS)

066117-YYY0A

FLANGE KIT

033757-0070A

TEE MOUNTING KIT

070847-0070A

CLIP

066118-0070A

PIVOT ROD

072574-0070A

EXTENSION ROD

900864-0070A

DRAIN BODY

TAILPIECE INSERT

070532-0070A

TAILPIECE

024220-0070A

COUPLING NUT

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1-800-442-1902

Weekdays 8:00 a.m. to 6:00 p.m. EST

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

IN MEXICO 01-800-839-1200

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .

© A S A m e r i c a , I n c . 2 0 0 9 60186 REV.1.5 (2/15)