This machine must be used for welding only. It must not be
used to defrost pipes.
It is also essential to pay special attention to the chapter on
The symbols next to certain paragraphs indicate points
requiring extra attention, practical advice or simple information.
This manual must be stored carefully in a place familiar to
everyone involved in using the machine. It must be consulted whenever doubts arise and be kept for the entire lifespan of the machine; it will also be used for ordering
replacement parts.
B) Adjustment knob.
This knob varies the welding wire feed speed
C) Central connector.
For connecting the welding torch
D) Ground connector.
Connector for the machine ground terminal
E) Selector switch.
Sets welding voltage. In some versions it switches the
machine on or off.
F) Adjustment knob.
This knob sets spot welding time.
Press the torch pushbutton to start welding.
Spot welding time is controlled by the knob.
To restart the cycle, release the torch pushbutton and
then press it again.
G) Led (green).
This Led indicates that the machine is on.
H) Led (yellow).
This Led lights up if the thermostat trips and stops the
welding machine.
Unpack the machine and place it in an adequately ventilated
area, dust-free if possible, taking care not to block the air
intake and outlet from the cooling slots.
CAUTION: REDUCED AIR CIRCULATION causes overheating and could damage internal parts.
Keep at least 500 mm of free space around the machine.
Never place any filtering device over the air intake points of
this welding machine.
The warranty shall become void if any type of filtering device
is used.
Mount the parts supplied with the machine as shown in the
figure 1.
Fig. 2
Fig. 1
This welding machine allows welding of mild steel, stainless
steel and aluminium.
A) Switch.
Switches the machine on or off.
EN60974.1 The welding machine is built according to these
international standards.
Serial number, which must always be indicated in
any inquiry regarding the welding machine.
Single-phase Transformer - Rectifier
Three-phase Transformer - Rectifier
External characteristics of the unit.
Secondary no-load voltage (peak value)
The duty cycle expresses the percentage of
10 minutes during which the welding machine
can run at a certain current without overheating.
Example: X = 60% at I2 = 100 A
This means that the machine can weld with a
current I2 = 100A for 6 out of 10 minutes, thus
Welding current
Secondary voltage with welding current I2
Rated power voltage.
1~ 50/60 Hz 50-or 60-Hz single-phase power supply.
3~ 50/60 Hz 50 or 60 Hz three-phase power supply.
Current absorbed at the corresponding welding current I2
Degree of housing protection.
Grade one as the second digit means that this
device is not suitable for use outdoors in the
Suitable for use in increased hazard areas.
Make sure that the wire diameter corresponds to the one
indicated on the roller, and mount the wire reel. Make sure
that the welding wire passes through the wire feed roller
After the final inspection, the three-phase welding machines
are connected to the voltage stated on the mains cable.
To change the supply voltage (three-phase version only)
remove the fixed side panel and set the connections of the
voltage-changing terminal board as shown in the figure.
The mains cable must be equipped with a plug suitable for
the current input.
Fig. 3
NOTE: The welding machine has also been designed for use
in environments with grade 3 pollution (see IEC 664)
This device is protected by a normally closed thermostat on
the power transformer.
When the thermostat is tripped the machine stops welding,
while the motor-driven fan continues to run and the yellow
LED lights.
After it has been tripped, wait a few minutes to allow the
generator to cool down.
The machine must be installed by skilled personnel. All
connections must be made in compliance with current
regulations and in full respect of safety laws (see standards
CEI 26-10 and CENELEC HD 427).
Before connecting the power cable (16), make sure that the
power voltage corresponds to that of the welding machine,
then:a) for permanent connection to the power mains without a plug, you must insert a main switch having a
suitable capacity in compliance with the rated specifications.
b) for a plug-socket connection, use a plug having a
suitable capacity in compliance with the rated specifications. In this case the plug must be used to
completely disconnect the machine from the mains,
after setting the switch to “O” (off).
The yellow-green wire must be connected to the earth
terminal. Connect the earth clamp to the part to be welded.
The welding circuit must not be deliberately placed in direct
or indirect contact with the protection wire except in the
If the workpiece is deliberately grounded using the protection wire, the connection must be as direct as possible, using
a wire at least as large as the welding current return wire, and
connected to the workpiece at the same point as the return
wire, using the return wire clamp or a second grounding
clamp placed next to it.
All precautions must be taken to avoid stray welding currents.
Turn the machine on using the switch.
Remove the tapered gas tip (51) by turning it clockwise.
Unscrew the contact tip (50).
Do not press the torch trigger until you have read the
instructions carefully.
It is important to make sure the machine is turned off
whenever changing the wire reel and wire roller, to prevent
the wire feed motor from starting accidentally.
Press the torch trigger (46) and release it only when the
welding wire comes out.
welding wire can cause puncture wounds.
Never aim the torch at parts of the body, other people or
metals when loading the welding wire.
Screw the contact tip (50) back on, making sure that the hole
diameter corresponds to the wire used.
Slide the tapered gas welding tip (51) on, always turning
Select the welding current by means of the rotary switch (24).
Move the torch near the welding point and press the trigger (46).
Adjust the potentiometerl (53) knob 2 until the welding is
done with a constant, continuous noise.
If the speed is too fast, the wire tends to stick to the piece and
cause the torch to skip; if the speed is too low, the wire melts
in spaced drops or the arc does not remain lit.
When you have finished welding, turn off the machine and
close the gas cylinder.
For the correct welding angle see figure 6.
5.1.2 Without gas protection.
Connect the cables as shown in the figure 5.
● The gas cylinder must be equipped with a pressure
reducer and flow meter.
● If the cylinder is placed on the cylinder holder of the
machine, it must be held in place by the chain provided and
be of an appropriate size to avoid jeopardizing the stability
of the machine.
● Connect the gas hose leaving the back of the machine to
the pressure reducer only after the cylinder is in place.
● Open the gas cylinder and set the flow meter to approximately 8-10 lt./min.
CAUTION: Make sure the gas used is compatible with the
material to be welded.
Fig. 5
Before using this welding machine, carefully read the regulations CEI 26/9 or CENELEC HD 407 and CEI 26/11 or
CENELEC HD 433. Also make sure that the insulation on
cables, torch and earth cable is intact.
5.1.1 With gas protection.
Either 75% ARGON + 25% CO2 or 100% CO2 may be used
for welding mild steel.
Connect the cables as shown in the figure 4.
Use only diam. 0.9 flux cored wire that complies with the
standard AWS AS.20 E71 TII or E71 TGS, suitable for use
without gaseous protection.
Connect the earth cable clamp to the workpiece.
After connecting the cables, follow the instructions given in
paragraph 5.1.1.
NOTE: For compact, well-protected welds always work from
left to right and from top to bottom.
Remove all waste after each welding operation.
For the correct welding angle see figure 6.
The welding machine must be prepared as for welding mild
steel with gas protection, but with the following differences:
- 100% ARGON as the protection gas for welding.
- A wire having a composition suited to the base material to
be welded.
- For welding ALLUMAN: 3÷5% silicon wire
- For welding ANTICORODAL: 3÷5% silicon wire
- For welding PERALUMAN: 5% magnesium wire
- For welding ERGAL: 5% magnesium wire
Use grinding wheels and brushes specifically designed for
aluminium, and never use them on other materials.
REMEMBER that cleanliness is quality!
The wire reels must be stored in nylon bags with dehumidifying packets.
For the correct welding angle see figure 6.
The welding machine must be prepared as for welding mild
steel with gas protection, but with the following differences:
- Reel of stainless steel wire compatible with the composition
of the material to be welded.
- Cylinder containing 98% ARGON + 2% 02 (recommended
The recommended torch angle and welding direction are
shown in figure 6.
In addition, this protects the manufacturer from being held
liable for defects when the true fault lies elsewhere.
6.2.1 Instructions for performing repairs
● After rewinding the transformer or inductance, the welding
machine must pass the applied voltage tests as indicated in
table 2 of paragraph 6.1.3 of the standard EN 60974.1 (CEI
26.13). Compliance must be verified as specified in 6.1.3.
● If no rewinding has been done, a welding machine that has
been cleaned and/or revised must pass an applied voltage
test with test voltage values equal to 50% of the values given
in table 2 of paragraph 6.1.3. Compliance must be verified
as specified in 6.1.3.
● After rewinding and/or replacing parts, the no-load voltage
must not exceed the values given in paragraph 10.1 of EN
● If the repairs have not been performed by the manufacturer,
repaired welding machines in which some components have
been replaced or altered must be marked in such a way that
the person who performed the repairs is clearly identifiable.
● After making repairs, take care to re-order the wiring so that
there is certain insulation between the primary side and the
secondary side of the machine. Prevent the wires from coming
into contact with moving parts or parts that heat up during
operation. Replace all clamps as on the original machine to
prevent a connection from occurring between the primary and
secondary side if a conductor accidentally breaks or disconnects.
Maintenance must be performed by skilled personnel.
The welding machine
supplies limited current
Line fuse blown
Replace line fuse
Burnt out diode or diodes
Burnt out electronic board
Turn off the welding machine and unplug the power cord
from the socket before each checking and maintenance
● Moving parts can cause serious lesions
● Keep away from moving parts.
● INCANDESCENT SURFACES can cause serious burns.
● Let the unit cool before servicing.
● Periodically remove any dust or foreign matter that may
have deposited on the transformer or diodes; to do so, use
a jet of clean, dry air.
● When replacing the wire roller, make sure the groove is
aligned with the wire and corresponds to the diameter of the
wire used.
● Always keep the interior of the gas nozzle clean to avoid
metal bridges created by welding dross between the gas
nozzle and the contact tip. Make sure the outlet hole of the
contact tip has not expanded excessively; if so, replace.
● Strictly avoid striking the torch or allowing it to suffer violent
Loosened torch or earth connec- Tighten all connections
tions or any other electrical power
Welding with a lot of
metal spatter
The wire jams or
entangles between the
drive rolls and the torch
infeed wire guide
Replace the switch
Improper adjustment of
welding parameters
Select the correct parameters through the weldingvoltage switch and the wirespeed adjustment potentiometer
Insufficient grounding
Check grounding
Contact tip with wrong
Misalignment of the drive roll
Obstructed or clogged liner
Remove and clean
No wire feed or irregular Drive roll with too large a
wire feed
Experience has shown that many mortal accidents are
caused by repairs performed incorrectly. That is why it is just
as important to check a repaired welding machine carefully
and completely as it is for a new welding machine.
Voltage adjustment switch
has a loose contact
Porosity in the welding
Replace the drive roll
Obstructed or clogged
Remove and clean
Wire holding roller not
completely tightened
Tighten all the way
Clogged contact tip
Insufficient shielding gas
Increase gas delivery
Excess oxidation of the
edges to be welded
Thoroughly clean the
edges with a metal brush
Gas nozzle partially or
completely clogged by
Remove and clean or
replace being careful not
to clog the gas outlets
7.1 Fire
● Avoid causing fire because of sparks, slag,
hot metal or pieces.
● Make sure that suitable fire-fighting equipment is available close to welding area.
● Remove all flammable and combustible material from the
welding area and its surrounding (32 ft minimum).
● Do not weld containers of combustible or flammable
material, even when empty. These must be carefully cleaned
before being welded.
● Allow the welded material to cool down before touching it or
putting it in contact with combustible or flammable material.
● Do not weld parts with hollow spaces, containing
● Do not work under conditions with high concentrations of
combustible vapours, gases, or flammable dust.
● Always check the work area half an hour after welding so
as to make sure that no fire has started.
● Do not keep any combustible material such as lighters or
matches in your pockets.
7.2 Burns
● Wear fire-proof clothing all over your body in order to protect
your skin against burns caused by ultraviolet radiation given off
by the arc, and from weld metal sparks and slag.
● Wear protective clothing-gauntlet gloves designed for use
in welding, hat and high safety-toe shoes. Button shirt collar
and pocket flaps, and wear cuff-less trousers to avoid entry
of sparks and slag.
● Wear helmet with safety goggles and glasses with side
shields underneath, appropriate filter lenses or plates (protected by clear cover glass). This is a MUST for welding to
protect the eyes from radiant energy and flying metal.
Replace cover glass when broken, pitted, or spattered.
● Avoid oil or greasy clothing. A spark may ignite them.
Hot metal such as electrode stubs and workpieces should
never be handled without gloves.
● First-aid facilities and a qualified first-aid person should be
available for each shift unless medical facilities are close by for
immediate treatment of flash burns of the eyes and skin burns.
● Ear plugs should be worn when working on overhead or in
a confined space. A hard hat should be worn when others
work overhead.
● Flammable hair preparations should not be used by
persons intending to weld or cut.
7.3 Fumes
Welding operations give off harmful fumes and metal
dusts which may be hazardous to your health, therefore:
● Work in a well-ventilated area.
● Keep your head out of fumes.
● In closed areas, use suitable exhaust fans.
● If ventilation is not enough, use breathing sets approved
for this procedure.
● Clean the material to be welded of any solvents or halogen
degreasers giving rise to toxic gases. Some clorine solvents
may decompose with the radiation emitted by the arc, and
create phosgene gas.
Do not weld plated metals or those containing lead,
graphite, cadmium, zink, chrome, mercury or beryllium,
unless you have the proper breathing set.
● The electric arc creates ozone. A long exposure to high
concentrations may cause headaches, nasal, throat and eye
irritation as well as serious congestions and chest pains.
● Gas leaks in a confined space should be avoided. Leaked
gas in large quantities can change oxygen concentration
dangerously. Do not bring gas cylinders into a confined space.
● DO NOT WELD where solvent vapors can be drawn into
the welding atmosphere or where the radiant energy can
penetrate to atmospheres containing even minute amounts
of trichloroethylene or perchloroethylene.
7.4 Explosions
Do not weld above or near containers under pressure.
● Do not weld in environments containing explosive
dusts, gases or vapours.
This welding machine uses inert gases such as CO2, ARGON, or a mixture of ARGON + CO2 for the protection of the
arc, thus you should take special precautions:
● Do not directly connect cylinder to the machine gas hose
without a pressure regulator.
● Handle or use pressure cylinders in conformity with the
existing rules.
● Do not use leaking or damaged cylinders.
● Do not use cylinders which are not well secured.
● Do not carry cylinders without the protection of the
installed valve.
● Do not use cylinders whose content has not been clearly
● Never lubricate cylinder valves with oil or grease.
● Do not put the cylinder in electrical contact with the arc.
● Do not expose cylinders to excessive heat, sparks, molten
slags or flame.
● Do not tamper with the cylinder valves.
● Do not try to loosen tight valves by means of hammers,
keys, or any other object.
● NEVER DEFACE or alter name, number, or other markings on a cylinder. It is illegal and hazardous.
● Do not lift cylinders off the ground by their valves or caps,
or by chains, slings or magnets.
● Never try to mix any gases in a cylinder.
● Never refill any cylinder.
● Cylinder fittings should never be modified or exchanged.
Keep pressure regulators in good condition. Damaged
regulators may cause damages or accidents, they should
only be repaired by skilled personnel.
● Do not use regulators for gases other than those for which
they are manufactured.
● Never use a leaking or damaged regulator.
● Never lubricate regulators with oil or grease.
● Replace hoses which appear damaged.
● Keep hoses unwound in order to avoid bending.
● Keep the excess hose wound and out of the working area
in order to avoid any damage.
7.5 Radiations
Ultra-violet radiation created by the arc may damage your eyes and burn your skin. Therefore:
● Wear proper clothing and helmet.
● Do not use contact lenses!! The intense heat coming from
the arc may cause them to stick to the cornea.
● Use masks with grade DIN 10 or DIN 11 safety lenses at
the least.
● Protect people in the surrounding welding area.
Remember: the arc may dazzle or damage the eyes. It is
considered dangerous up to a distance of 15 meters (50
feet). Never look at the arc with the naked eye.
● Prepare the welding area so as to reduce reflection and
transmission of ultra-violet radiation. Paint walls and exposed surfaces in black to reduce reflection, install sheathings
or curtains to reduce ultra-violet transmissions.
● Replace mask lenses whenever damaged or broken.
Electric shock
Electric shock can kill.
All electric shocks are potentially fatal.
● Do not touch live parts.
● Insulate yourself from the piece to be cut and from the
ground by wearing insulated gloves and clothing.
● Keep garments (gloves, shoes, hats, clothing) and body dry.
● Do not work in humid or wet areas.
● Avoid touching the piece to be welded.
● Should you work close to or in a dangerous area, use all
possible precautions.
● If you should feel even the slightest electric shock sensation, stop welding immediately. Do not use the machine until
the problem is identified and solved.
● Always fit an automatic wall switch with adequate power,
possibly close to the machine, allowing you to immediately
switch the machine off in case of an emergency.
● Frequently inspect the power supply cable.
● Disconnect power supply cable from mains before replacing cables or before removing unit covers.
● Do not use the unit without protection covers.
● Always replace any damaged parts of the unit, with original
● Never disconnect unit safety devices.
● Make sure that the power supply line is equipped with an
efficient earth plug.
● Make sure that the work bench and the workpiece are
connected to an efficient earth plug.
● Any maintenance should only be carried out by qualified
personnel aware of the risks due to dangerous voltages
necessary for the operation of the unit.
7.7 Pace maker
● Magnetic fields from high currents can affect pacemaker
operation. Persons wearing electronic life support equipment (pacemaker) should consult their doctor before going
near arc welding, gouging or spot welding operations.
7.8.Caution! Welding wire can cause puncture wounds.
● Do not press gun trigger until instructed to do so.
● Do not point gun toward any part of the body, other people,
or any metal when threading welding wire.
7.9.Moving parts can cause injury.
Moving parts, such as fans, can cut fingers and hands and
catch loose clothing.
● Keep all doors, panels, covers, and guards closed and
securely in place.
● Have only qualified people remove guards or covers for
maintenance and troubleshooting as necessary.
● Keep hands, hair, loose clothing, and tools away from
moving parts.
● Reinstall panels or guards and close doors when servicing
is finished and before starting the machine.
These power source alone do not produce noise
levels exceeding 80 dB. The welding procedure,
however, may produce noise levels in excess of 80
dB. in which case the machine operator must take the
necessary safety precautions as prescribed by the national
safety regulation.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF