NEC NEAX2000 IVS2 General Description (1)

NEC NEAX2000 IVS2 General Description (1)
NDA-24293
ISSUE 2
STOCK # 152017
®
General Description
SEPTEMBER, 2000
NEC America, Inc.
LIABILITY DISCLAIMER
NEC America, Inc. reserves the right to change the specifications, functions, or
features, at any time, without notice.
NEC America, Inc. has prepared this document for use by its employees and
customers. The information contained herein is the property of NEC America,
Inc. and shall not be reproduced without prior written approval from NEC
America, Inc.
NEAX® and Dterm® are registered trademarks of NEC Corporation.
All other brand or product names are or may be trademarks or registered
trademarks of, and are used to identify products or services of their respective
owners.
Copyright 2000
NEC America, Inc.
Printed in the U.S.A
NDA-24293
ISSUE 2
SEPTEMBER, 2000
NEAX2000 IVS2
General Description
TABLE OF CONTENTS
Page
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
x
xi
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xiii
Regulatory Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCC Part 15 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCC Part 68 Registration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Company Notification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Location of FCC Compliance Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FCC Requirements for Private Line Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct-Inward Dialing (DID) Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regulatory Information On Single-line Analog Telephones . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hearing Aid Compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Industry Canada CS-03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1
xiii
xiii
xiv
xiv
xiv
xv
xv
xvii
xviii
xviii
xviii
xx
xx
xxi
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Feature Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Modularity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flexible Interface Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fusion of RAM and ROM Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Feature Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Feature Package Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Licensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Advantages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
1
1
3
4
4
4
5
5
5
5
6
6
7
7
7
10
Page i
TABLE OF CONTENTS (CONTINUED)
Page
Chapter 2
System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trunking Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Layout of PIM (SN1480 PIMF). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Card Mounting Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 3
11
12
13
15
16
17
18
Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
Dterm Series III . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Advantages of Dterm Series III . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dedicated Feature Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dterm Series III Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dterm Series III Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Line Conditions of Each Dterm Series III Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
term
D
Series E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dterm Series E Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Line Conditions of Each Dterm Series E Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SN716 DESKCON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SN716 DESKCON Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Line Conditions of the SN716 DESKCON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
19
20
20
21
25
26
26
27
30
31
32
32
Chapter 4
Equipment Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Common Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog C.O. Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog DID Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Tie Line Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Station. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Trunk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CCIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ISDN/ECCIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IP Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Miscellaneous Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System I/O, OAI, ACD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voice Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optical Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page ii
33
33
33
34
34
34
34
35
35
35
35
36
36
36
37
37
37
38
38
38
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
TABLE OF CONTENTS (CONTINUED)
Page
Chapter 5
Feature Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Account Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Add-On Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarm Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alphanumeric Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Port Adapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Announcement Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Answer Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Assisted Calling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Camp-on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SN716 DESKCON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Called/Calling Name Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Called/Calling Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Call Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Console Lockout - Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Do Not Disturb Setup And Cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Interposition Calling/Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Lamp Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Listed Directory Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Loop Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Training Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audible Indication Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Processing Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Queuing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Splitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Waiting Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Common Route Indial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialed Number Identification Service (DNIS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Incoming Call Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Individual Trunk Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multi-Function Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiple Console Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pushbutton Calling - Attendant Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Time Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trunk Group Busy Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unsupervised Trunk-to-Trunk Transfer By Attendant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Delay Announcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Overflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Override. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Authorization Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automated Attendant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
39
39
39
39
39
40
40
40
40
40
40
40
41
41
41
41
41
41
41
41
41
41
41
42
42
42
42
42
42
42
42
42
42
43
43
43
43
43
43
43
43
43
44
44
Page iii
TABLE OF CONTENTS (CONTINUED)
Page
Automatic Call Distribution (ACD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Busy In/Busy Out - ACD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Waiting Indication - ACD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delay Announcement - ACD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hunt Past No Answer - ACD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Immediate Overflow - ACD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Priority Queuing - ACD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Queue Size Control - ACD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Silent Monitor - ACD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Call Distribution with Management Information System (MIS) . . . . . . . . . . . . . . . . . .
Automatic Camp-on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Number Identification (ANI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Wake-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Background Music . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boss / Secretary Calling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Broker's Call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Call Forwarding Set-up and Cancel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Forwarding - All Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Forwarding - Busy Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Forwarding - No Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Forwarding - Destination. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiple Call Forwarding - All Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiple Call Forwarding - Busy Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiple Call Forwarding - No Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Split Call Forwarding - All Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Split Call Forwarding - Busy Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Split Call Forwarding - No Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Forwarding - Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Group Diversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Park - System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Park - Tenant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Pickup - Direct. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Pickup - Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Pickup - Designated Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Redirect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Transfer - Al lCalls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Transfer - Attendant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caller ID Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caller ID Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Camp-on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page iv
44
44
44
44
44
44
44
45
45
45
45
45
45
45
46
46
46
46
46
47
47
47
47
47
47
47
47
47
47
48
48
48
48
48
48
48
48
48
48
49
49
49
49
49
49
49
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
TABLE OF CONTENTS (CONTINUED)
Page
Centrex Compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Check In / Check Out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Class of Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Code Restriction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conference (Three/Four Party) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conference (Six/Ten Party) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Consecutive Speed Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Consultation Hold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Customer Administration Terminal (CAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Line Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delayed Ringing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dial By Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dial Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct Data Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct Digital Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct Inward Dialing (DID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DID Call Waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DID Digit Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct Inward System Access (DISA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct Inward Termination (DIT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct Outward Dialing (DOD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct Station Selection/Busy Lamp Field (DSS/BLF) Console . . . . . . . . . . . . . . . . . . . . . . . . . .
Busy Out Status Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Do Not Disturb Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Message Waiting Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Room Cutoff Console. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wake Up No Answer Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distinctive Ringing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Do Not Disturb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Do Not Disturb - Hotel/Motel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Do Not Disturb-System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Elapsed Call Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enhanced 911 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Executive Calling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Executive Override. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Paging with Meet-Me . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fax Arrival Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Feature Activation from Secondary Extension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flexible Line Key Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flexible Numbering Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flexible Ringing Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Forced Account Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Group Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Conference (6/10 Party) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Way Calling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
49
50
50
50
50
50
50
51
51
51
51
51
51
51
52
52
52
52
52
52
52
52
53
53
53
53
53
53
54
54
54
54
54
54
54
55
55
55
55
55
55
55
56
56
56
56
Page v
TABLE OF CONTENTS (CONTINUED)
Page
Group Listening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hands-free Answerback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hands-free Dialing and Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dual Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exclusive Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-exclusive Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hotel/Motel Attendant Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hotel/Motel Front Desk Instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hotline - Inside/Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
House Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Individual Attendant Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intercept Announcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dial Intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Tone/Voice Signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Zone Paging with Meet-Me . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Last Number Redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Least Cost Routing - 3/6 Digit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Line Lockout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Line Pre-selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maid Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance Administration Terminal (MAT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Message Center Interface (MCI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Message Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Message Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Message Waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Miscellaneous Trunk Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CCSA Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Code Calling Equipment Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dictation Equipment Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Foreign Exchange (FX) Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Paging Equipment Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wide Area Telephone Service (WATS) Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiline Terminal Attendant Position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Music on Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nailed-down Connection - Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Night Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attendant Night Transfer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Rerouting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Day / Night Mode Change by Attendant Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Day / Night Mode Change by Station Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Night Connection - Fixed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page vi
56
56
56
56
56
57
57
57
57
57
57
57
57
57
58
58
58
58
58
58
58
59
59
59
59
59
59
59
60
60
60
60
60
60
60
60
61
61
61
61
61
61
61
61
62
62
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
TABLE OF CONTENTS (CONTINUED)
Page
Night Connection - Flexible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trunk Answer Any Station (TAS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Off-hook Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Off-Premises Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Open Application Interface (OAI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pad Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Periodic Time Indication Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pooled Line Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Failure Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Priority Call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Privacy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct Privacy Release. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Privacy Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Private Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Property Management System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Proprietary Multiline Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Idle Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Called Station Status Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calling Name and Number Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dynamic Dial Pad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Handsfree Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I-Hold / I-Use Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Microphone Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiple Line Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mute Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Off-Hook Voice Announcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Prime Line Pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recall Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Relay Control Function Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ring Frequency Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ringing Line Pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Soft Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Volume Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q-SIG Circuit Switched Basic Call - ETSI Version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reserve Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resident System Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Return Message Schedule Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Room Cutoff. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Room Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Route Advance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save and Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Relocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Single Digit Dialing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
62
62
62
62
62
62
63
63
63
63
63
63
63
63
64
64
64
64
64
64
64
64
64
64
65
65
65
65
65
65
65
65
65
66
66
66
66
66
66
66
67
67
67
67
67
67
Page vii
TABLE OF CONTENTS (CONTINUED)
Page
Software Line Appearance (Virtual Extensions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stack Dial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Station Hunting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Station Hunting - Circular. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Station Hunting - Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Station Hunting - Secretarial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Station Message Detail Recording (SMDR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Station Speed Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supervisory Control of Peripheral Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Speed Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tenant Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tie Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tie Line Tandem Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timed Queue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timed Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trunk - Direct Appearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trunk Queuing - Outgoing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trunk-to-Trunk Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Uniform Call Distribution (UCD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Busy In/Busy Out-UCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Waiting Indication-UCD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delay AnnouncementUCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hunt Past No Answer-UCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Immediate Overflow-UCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Priority Queuing-UCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Queue Size Control-UCD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Silent Monitor-UCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Uniform Numbering Plan (UNP) -Voice and Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Variable Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voice Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voice Mail Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voice Mail Private Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voice Mail Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Whisper Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 6
Installation Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Items to be Provided at Site. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heat Dissipation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page viii
67
68
68
68
68
68
68
68
69
69
69
69
69
69
70
70
70
70
70
70
71
71
71
71
71
71
71
71
71
72
72
72
72
72
73
73
75
75
76
76
76
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
TABLE OF CONTENTS (CONTINUED)
Page
Chapter 7
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trouble Reporting and Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 8
System Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rotary Dial Pulse and DTMF Signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audible Tones and Ringing Signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audible Tones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ringing Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Built-In Modem on MP Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BHCA (Busy Hour Call Attempts) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
77
77
78
78
79
79
79
80
81
81
81
81
82
Page ix
LIST OF FIGURES
Figure
Title
Figure 2-1
Figure 2-2
Figure 2-3
Figure 2-4
Figure 3-1
Figure 3-2
Figure 3-3
Figure 3-4
Figure 3-5
Figure 3-6
Figure 3-7
Figure 3-8
Floor Standing Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wall-Mounting Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rack Mounting Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MP/FP Card Mounting Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dterm S IIID SLT (ETJ-1DT-1) - Single Line Digital Instrument . . . . . . . . . . . . . . . . . .
Dterm 8 (ETJ-8-1) - 8 Button Digital Instrument without LCD Display . . . . . . . . . . . . . .
Dterm 8IS (ETJ-8IS-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dterm 16DC (ETJ-16DC-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dterm 16DD (ETJ-16DD-I) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dterm 24DS (ETJ-24DS-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dterm Series IIIA (ETJ-1-1) - Single Line Analog Telephone . . . . . . . . . . . . . . . . . . . .
Dterm Series IIIH (ETJ-1HM) - Single Line Analog Telephone
with 8 Speed Dial Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EDW-48-2 DSS/BLF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Dterm III Adapters - ADA-J, APA-J, APR-J, LLA-J and CTA-J . . . . . . . . . . . . .
DTP-8-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTP-8D-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTP-16D-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTP-32D-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTP-2DT-1 (WH) TEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DCU-60-1 Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SN716 DESKCON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-9
Figure 3-10
Figure 3-11
Figure 3-12
Figure 3-13
Figure 3-14
Figure 3-15
Figure 3-16
Figure 3-17
Page x
Page
13
14
14
18
21
22
22
22
23
23
23
24
24
24
27
27
28
28
29
29
31
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
LIST OF TABLES
Table
Table 3-1
Table 3-2
Table 3-3
Table 6-1
Table 7-1
Table 8-1
Title
Page
term
Line Conditions of Each D
Series III Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . .
term
Line Conditions of Each D
Series Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Line Conditions of the SN716 DESKCON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications for Heat Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault Detection Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications of Audible Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
25
30
32
76
77
81
Page xi
This page is for your notes.
Page xii
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Regulatory Information
Regulatory Requirements
The Federal Communications Commission (FCC) has established rules that permit the
PBX to be directly connected to the telephone network. A jack is provided on party
lines or coin lines.
The telephone company may make changes in its technical operations and procedures.
If such changes affect the compatibility or use of the PBX, the telephone company
must provide adequate notice of the changes.
This equipment complies with the requirements in Part 15 of FCC Rules for a Class A
computing device. Operation of this equipment in a residential area may cause
unacceptable interference to radio and TV reception requiring the operator to take
whatever steps are necessary to correct this interference.
FCC Part 15 Requirements
In compliance with FCC Part 15 Rules, the following statement is provided:
Warning:
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
This equipment generates, uses, and can radiate radio frequency energy
and if not installed and used in accordance with the instruction manual,
may cause interference to radio communications. It has been tested and
found to comply with the limits for a Class A computing device pursuant to
Subpart J of Part 15 of FCC Rules, which are designed to provide
reasonable protection against such interference when operated in a
commercial environment. Operation of this equipment in a residential
area is likely to cause interference in which case the user at his own
expense will be required to take whatever measures may be required to
correct the interference.
Page xiii
FCC Part 68 Registration
Regulatory Information
FCC Part 68 Registration
Company
Notification
Before installing the PBX to the telephone network, the telephone company must be
provided with the following:
•
Your telephone number
•
The FCC registration numbers:
JAPAN
USA
PBX
AY5JPN-20542-PF-E
AY5USA-21582-PF-E
Hybrid
AY5JPN-20543-MF-E
AY5USA-21583-MF-E
Key System
AY5JPN-20586-KF-E
AY5USA-21584-KF-E
The Ringer Equivalence Number is 1.6B; the required USOC jacks are RJ21X,
RJ2EX, RJ2GX, and RJ49C.
Note:
Service
Requirements
Limitations on features exist if the system is registered as a KF system. Refer
to Features and Specifications for details.
In the event of equipment malfunction, all repairs will be performed by NEC or an
authorized distributor. It is the responsibility of users requiring service to report the
need for service to NEC or to one of their authorized distributors.
If trouble is experienced with this equipment, please contact NEC America, Inc., at
800-TEAM NEC (800-832-6632) for repair and/or warranty information. If the
trouble is causing harm to the telephone network, the telephone company may request
that you remove the equipment from the network until the problem is resolved.
If the equipment causes harm to the telephone network, the telephone company will
notify you in advance that temporary discontinuance of service may be required. If
advance notice is not practical, the telephone company will notify the customer as
soon as possible. Also, you will be advised of your right to file a complaint with the
FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations, or
procedures that affect the operation of the equipment. If this happens, the telephone
company will provide advance notice so that you can make necessary modifications in
order to maintain uninterrupted service.
NO REPAIRS CAN BE DONE BY THE CUSTOMER.
Page xiv
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Regulatory Information
Location of FCC Compliance Labels
Location of FCC Compliance Labels
Labels stating the NEAX2000 IVS2 FCC registration number and compliance with
FCC Parts 15 and 68 are attached on the inside of the system's front cover. Label
examples are as follows:
“This equipment complies with the
requirements in Part 15 of FCC Rules for a
Class A computing device. Operation of
this equipment in a residential area may
cause unacceptable interference to radio
and TV reception requiring the operator to
take whatever steps are necessary to
correct the interference.”
FCC Requirements
for Private Line
Operations
NEAX2000 IVS2
Complies With Part 68 FCC Rules
FCC Registration Numbers:
Ringer Equivalence: 1.6B
NEC America, Inc. MADE IN USA
In order to connect this system to the private line network, provide the telephone
company with:
•
The quantities and USOC numbers of the required jacks (See the following table.)
•
The sequence in which the trunks are to be connected
•
The facility interface codes by position
•
The Ringer Equivalence Number or service order code, as applicable, by position
MFG'S PORT ID
FACILITY
INTERFACE CODE
NETWORK
JACKS
PN-4COTB
02LS2
RJ21X
PN-4COTB
02GS2
RJ21X
PN-4COTG
02LS2
RJ21X
PN-4COTG
02ES2
RJ21X
PN-AUCA
02RV2-T
RJ21X
PN-4DITB
02RV2-T
RJ21X
PZ-8PFTA
02LS2
RJ21X
PN-8COTQ
02LS2
RJ21X
PN-8COTS
02LS2
RJ21X
PN-8COTS
02GS2
RJ21X
PN-AUCA
0L13A, 0L13B, 0L13C
RJ21X
9.0F
PN-20DTA
TL11M
RJ2EX
9.0F
PN-20DTA
TL31M
RJ2GX
9.0F
PN-24DTA
04DU9-BN
N/A
6.0P
PN-24DTA
04DU9-DN
N/A
6.0P
PN-24DTA
04DU9-1KN
N/A
6.0P
PN-24DTA
04DU9-ISN
N/A
6.0P
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
SERVICE ORDER
CODE
Page xv
Location of FCC Compliance Labels
Page xvi
Regulatory Information
MFG'S PORT ID
FACILITY
INTERFACE CODE
NETWORK
JACKS
SERVICE ORDER
CODE
PN-24DTA
04DU9-IZN
N/A
6.0P
PN-BRTA
02IS5
RJ49C
6.0Y
PN-DAIA
04DU9-BN
N/A
6.0N
PN-DAIA
04DU9-DN
N/A
6.0N
PN-DAIA
04DU9-1KN
N/A
6.0N
PN-DAIA
04DU9-1SN
N/A
6.0N
PN-DAIA
04DU9-1ZN
N/A
6.0N
PN-DAIA
04DU9-BN
N/A
6.0N
PN-DAIB
04DU9-BN
N/A
6.0N
PN-DAIB
04DU9-DN
N/A
6.0N
PN-DAIB
04DU9-1KN
N/A
6.0N
PN-DAIB
04DU9-1SN
N/A
6.0N
PN-DAIB
04DU9-1ZN
N/A
6.0N
PN-24PRT-A
05DU9-BN
N/A
6.0P
PN-24PRT-A
04DU9-BN
N/A
6.0P
PN-24PRT-A
04DU9-1KN
N/A
6.0P
PN-24PRT-A
04DU9-1SN
N/A
6.0P
PN-24PRT-A
04DU9-1ZN
N/A
6.0P
PN-24CCT-A
04DU9-BN
N/A
6.0P
PN-24CCT-A
04DU9-DN
N/A
6.0P
PN-24CCT-A
04DU9-1KN
N/A
6.0P
PN-24CCT-A
04DU9-1SN
N/A
6.0P
PN-24CCT-A
04DU9-1ZN
N/A
6.0P
PN-24DTA-C
04DU9-BN
N/A
6.0P
PN-24DTA-C
04DU9-DN
N/A
6.0P
PN-24DTA-C
04DU9-1KN
N/A
6.0P
PN-24DTA-C
04DU9-1SN
N/A
6.0P
PN-24DTA-C
04DU9-1ZN
N/A
6.0P
PN-2BRTC
02IS5
N/A
6.0Y
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Regulatory Information
Direct-Inward Dialing (DID) Calls
Direct-Inward Dialing (DID) Calls
Allowing this equipment to be operated in such a manner as to not provide for proper
answer supervision is a violation of Part 68 of the FCC's rules.
PROPER ANSWER SUPERVISION IS WHEN:
a.) This equipment returns answer supervision to the PSTN when DID calls are:
•
Answered by the called station
•
Answered by the attendant
•
Routed to a recorded announcement that can be administered by the CPE user
•
Routed to a dial prompt
b.) This equipment returns answer supervision on all DID calls forwarded to the
PSTN.
•
Permissible exceptions are:
•
A call is unanswered
•
A busy tone is received
•
A reorder tone is received
EQUAL ACCESS REQUIREMENTS
This equipment is capable of providing users access to interstate providers of operator
services through the use of access codes. Modification of this equipment by call
aggregators to block access dialing codes is a violation of the Telephone Operator
Consumers Act of 1990.
Caution:
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
The use of a monitoring, recording or listening devices to eavesdrop,
monitor or record telephone conversations or other sound activities,
whether or not contemporaneous with its transmission, may be illegal in
certain circumstances under federal or state laws. Legal advice should be
sought prior to implementing any practice that monitors or records any
telephone conversation. Some federal and state laws require some form of
notification to all parties to the telephone conversation, such as using a
beep tone or other notification methods or require the consent of all
parties to the telephone conversation, prior to monitoring or recording a
telephone conversation. Some of these laws incorporate strict penalties.
Page xvii
Regulatory Information On Single-line Analog Telephones
Regulatory Information
Regulatory Information On Single-line Analog Telephones
NEC single-line telephones comply with Part 68 of FCC Rules. On the bottom of the
equipment is a label that states, among other information, the FCC registration
number and ringer equivalence number (REN) for the equipment. If requested, this
information should be provided to the telephone company.
The equipment uses the following USOC jacks: RJ11C.
The equipment should be used only behind a PBX or KTS. The REN is used to
determine the number of devices that may be connected to the telephone line.
Excessive RENs on the telephone line may result in the devices not ringing in
response to an incoming call. In most, but not all, areas, the sum of RENs should not
exceed five (5.0). To be certain of the number of devices that may be connected to the
line as determined by the total RENs, contact the telephone company to determine the
maximum REN for the calling area.
Hearing Aid Compatibility
The Dterm terminals provided for the NEAX2000 IVS2 are hearing aid compatible.
FCC rules prohibit the use of non-hearing aid compatible telephones.
NEC-type single-line telephone sets used in conjunction with the NEAX2000 IVS2
are hearing aid compatible. If other than NEC-type single-line telephone sets are to be
used with this system, ensure that these are hearing aid compatible.
Industry Canada CS-03
Certification number: 140 5976 A
Load Number of the equipment: 1.0
NOTICE: The Industry Canada label identifies certified equipment. The certification
means that the equipment meets certain telecommunications network protective
operational and safety requirements. The department does not guarantee the
equipment will operate to the user's satisfaction.
Page xviii
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Regulatory Information
Industry Canada CS-03
Before installing the equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The equipment
must also be installed using an acceptable method of connection. In some cases, the
company's inside wiring associated with a single line individual service may be
extended by means of a certified connector assembly (telephone extension cord). The
customer should be aware that compliance with the above conditions might not
prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or installations made by
the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request that the user disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines, and internal metallic water pipe system, if present,
are connected together. This protection may be particularly important in rural areas.
Caution:
Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as
appropriate.
NOTICE: The Load Number assigned to each terminal device denotes the percentage
of the total load to be connected to a telephone loop which is used by the device, to
prevent overloading. The termination on a loop may consist of any combination of
devices subject only to the requirement that the total of the load numbers of all the
devices does not exceed 100.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page xix
Safety Certifications
Regulatory Information
Safety Certifications
This equipment has been listed by Underwriters Laboratories and found to comply
with all the applicable requirements of the standard for telephone equipment U.L.
1459. This equipment complies with Canadian Standards Association's standard
C 22.2 No. 225.
Safety
Considerations
When using telephone equipment, basic safety precautions should always be followed
to reduce the risk of fire, electric shock, and injury. Precautions include the following:
•
Never install telephone wiring during a lightning storm.
•
Never install a telephone jack in a wet location, unless the jack is specifically
designed for wet locations.
•
Never touch an uninsulated telephone wire or terminal, unless the telephone line
has been disconnected at the network interface.
•
Use caution when installing or modifying telephone lines.
Note:
Page xx
More detailed precautions are included in this manual.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Regulatory Information
Safety Instructions
Safety Instructions
1. Never install telephone wiring during a lightning storm.
2. Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
3. Never touch un-insulated telephone wires or terminals unless the telephone line
has been disconnected at the network interface.
4. Use caution when installing or modifying telephone lines.
5. Read and understand all instructions.
6. Follow all warnings and instructions marked on the product.
7. Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
8. Do not use this product near water, for example, under water pipes near a bathtub,
sink, or laundry tub, in a wet basement, or near a swimming pool.
9. Do not place this product on an unstable cart, stand, or table. The product may
fall, causing serious damage to the product.
10. Slots and openings in the cabinet and the back or bottom are provided for
ventilation, to protect it from overheating, these openings must not be blocked or
covered. The openings should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should never be placed near or
over a radiator or heat register. This product should not be placed in a built-in
installation unless proper ventilation is provided.
11. This product should be operated only from the type of power source indicated on
the marking label. If you are not sure of the type of power source available,
consult with your local power company.
12. This product is normally connected with a three-wire grounding type plug, a plug
having a third (grounding) pin. This plug will only fit into a grounding type power
outlet. This is a safety feature. If you are unable to insert the plug into the outlet,
contact an electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the grounding type plug. SAFETY INSTRUCTIONS
13. Do not allow anything to rest on the power cord. Do not locate this product where
the cord will be abused by persons walking on it.
14. Do not overload wall outlets and extension cords as this can result in the risk of
fire or electric shock.
15. Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a risk of fire
or electric shock. Never spill liquid of any kind on the product.
16. To reduce the risk of electric shock, do not disassemble this product, but take it to
a qualified serviceman when some service or repair work is required. Opening or
removing covers may expose you to dangerous voltages or other risks. Incorrect
reassembly can cause electric shock when the appliance is subsequently used.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page xxi
Safety Instructions
Regulatory Information
17. Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a.) When the power supply cord or plug is damaged or frayed.
b.) If liquid has been spilled into the product.
c.) If the product has been exposed to rain or water.
d.) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions, because improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal operation.
e.) If the product has been dropped or the cabinet has been damaged.
f.) If the product exhibits a distinct change in performance.
18. Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning.
19. Do not use the telephone to report a gas leak in the vicinity of the leak.
Page xxii
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 1
Introduction
This manual provides an overview of the NEAX2000 IVS2 (Integrated Voice Server2)
stored program control digital electronic PBX. An introduction to the technical
characteristics is included, along with a description of available system applications.
System Overview
The NEAX2000 IVS2 is a full-featured PBX providing a rich feature set of both Key
and PBX features. It is positioned to provide a more cost effective solution for the
small to medium size business, hotel property or networked environment. This system
allows users to purchase just the station and trunk capacity that they need, yet expand
that capacity by simply adding modules to accommodate added demand. The modular
design of the NEAX2000 IVS2 allows the system to grow from 24 to 512 stations.
Hardware modularity results in one of the most reliable, flexible, and powerful
systems available.
The NEAX2000 IVS2 is a microprocessor-based, stored-program-controlled, digital
communication system using the Pulse Code Modulation (PCM) technique. The
system is comprised of central equipment cabinets and telephones located throughout
the installation site. The central equipment cabinet is composed of Port Interface
Modules (PIMs). One to Eight PIMs may be installed, depending on the requirements
of the individual customer. The PIMs are designed for modular growth, stack
mounting (4 PIMs high), and quick interconnection. Each PIM provides 64 ports. The
universal port design minimizes the hardware required for a system, and provides
greater flexibility in the number and types of devices that can be installed.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 1
System Overview
Chapter 1 Introduction
The NEAX2000 IVS2 is based on a universal port concept. A total of 768 ports can be
equipped, a maximum of 512 stations/analog trunks plus 256 Virtual extensions.
These ports support Dterm Series III/E, Electra Elite, Dterm Cordless, and Dterm PSII
(Wireless) Multiline Terminals, single line telephones, outside lines, and other circuits
and devices. While port assignment is flexible, the maximum capacities for each
device are as follows:
DEVICES
WITHOUT
MEM-MODULE
WITH
MEM-MODULE
Analog + Digital + Trunks + Wireless lines
384
768
DID Number Conversions
500
1000
1 (16 IP CH)
8 (128 IP CH)
Analog lines
256
512
Digital lines
256
512
Analog + Digital + Wireless lines
256
512
Virtual lines
256
512
Virtual + Digital lines
512
768
Wireless PS lines
128
256
ISDN-BRI lines
64
128
Data lines
64
128
Call Forward Outside
240
496
Auth/Forced/DISA ID Code
1000
3000 (on MP)
Message Reminder
512
1024
Name Display (My-Line + Virtual)
256
512
Station Speed Dial
4000
10,000
Built-In SMDR (Standalone)
256
1280
Digital Trunks (T1)
240 ch
240 ch
ISDN PRI
192 ch
192 ch
CCIS #7
192 ch
192 ch
IP Trunks
Page 2
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 1 Introduction
Feature Overview
Feature Overview
The Primary design objective of our NEAX2000 IVS 2 is to offer affordable
communications and features designed to enhance your company’s performance. A
comprehensive feature package is provided including both business and Hotel/Motel
features.
•
Business – concentrates on call processing to streamline daily business
communication operations.
•
Hotel/Motel – designed to provide your administration station with the most
effective features for optimum guest service. Guest stations are offered
features to provide them with optimum hospitality.
Throughout the use of the NEAX2000 IVS2 features, your company can control costs,
enhance productivity, save time, and take advantage of flexible resources.
The NEAX2000 IVS2 employs techniques such as resident system programming and
maintenance (both online and remote). These techniques ensure the installation and
maintenance is quick and efficient.
Cost control is served by features such as:
Account Codes, Forced Account Codes, Direct Inward System Access (DISA), Least
Cost Routing (LCR), Route Advance, Station Message Detail Recording (SMDR),
Code Restriction, Elapsed Call Timer, Periodic Time Indication Tone, Off-Premises
Extensions, and Tandem Switching of E&M Tie Lines.
Productivity is served by features such as:
Incoming Call Identification (transfers, DIT, DID, DDD, FX, WATS and internal
calls), Authorization Code, Automated Attendant, Camp-On, Group Listening,
Hands-free Answerback, Call Park, Do Not Disturb, Callback, Call Forward, Call
Pickup, Conference, Data, Return Message Schedule Display, Timed Reminder, Trunk
Queuing, and Set Relocation.
Time saving is served by features such as:
Speed Dial, Save and Repeat, Callback Message, Last Number Redial, Answer Key,
Ringing Line Pickup, VoiceMail Integration, Broker's Call, Step Call, Trunk to Trunk
Transfer, Timed Queue, Boss/Secretary Calling, Intercoms, Remote Maintenance,
Voice Mail Soft-Keys and Dial by Name.
Flexibility is served by the universal port concept, which allows a high variable trunk
to station ratio, Flexible Line Key Assignment, Flexible Ringing Assignment, Direct
Trunk Appearance, as well as Flexible Numbering Plan. The variety of telephones
(detailed in Section 3) also adds to the system's flexibility.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 3
Hardware Architecture
Chapter 1 Introduction
Hardware Architecture
The NEAX2000 IVS2 employs the latest advancements in Large Scale Integration
(LSI) circuits and component manufacturing techniques to create a highly reliable and
serviceable communications system.
The NEAX2000 IVS 2 architecture consists of three major functional components:
Distributed Controller, Digital Switching Network, and Port Interface.
1. Distributed Controller
The Distributed Controller is composed of distributed multiprocessing units,
generic memory, database instructions, system interface, and interface ports for
system maintenance and administration.
2. Digital Switching Network
The Digital Switching Network consists of a non-blocking digital time division
switch, allowing all ports to be used simultaneously.
3. Port Interface
The Port Interface provides access to the public and private network for various
types of terminal devices, including digital and analog telephones, data terminals,
computers and subsystems such as Voice Mail Systems, Data Switch Networks,
and related communication and information services.
Hardware
Modularity
The NEAX2000 IVS 2 continues with the modular design employing interface
modules in groups of 64 ports. The system allows users to purchase just the station
and trunk capacity that they need, yet expand that capacity by simply adding modules
to accommodate added demand. The modular design of the NEAX2000 IVS 2 allows
the system to grow from 24 to 512 ports. Hardware modularity results in one of the
most reliable, flexible, and powerful systems available.
Flexible Interface
Port
The IVS2 uses a Universal Port architecture that has the flexibility to accommodate
station terminals, trunks, and adjunct processors. This universal digital back plane
allows the NEAX2000 IVS2 to maximize slot space utilization and lower expansion
costs.
Page 4
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 1 Introduction
Cabling
Software Architecture
As more and more computers and communications devices use twisted-pair
technology, the use of today’s cabling systems continues to rise. This is of special
concern when the customers’ needs require that the cabling system be expanded
where facilities are close to their capacity. The NEAX2000 IVS2 provides solutions
that significantly reduce overall cabling requirements.
The Dterm Series III and Series E digital telephones offer cost-effective use of cabling
systems by requiring only a single twisted pair. This new technology provides the
power and function of the previous Dterm telephones with 50% less cabling.
Software Architecture
The NEAX2000 IVS2 software design is as advanced as its hardware. It ensures that
your system will support the evolving applications and have the reliability needed to
take your organization into the future.
Fusion of RAM and
ROM Programs
The NEAX2000 IVS2 incorporates the flexibility of Random Access Memory (RAM)
for Office Data Memory, and Flash ROM which contains the operating system. This
fusion of divergent memory technologies results in high performance 32-bit
processing reliability in system operation as well as fast recovery time in case of
system power loss. This unique configuration provides improved efficiency for
updates to the generic program by floppy disk, and simplifies upgrades for system
features and capabilities throughout its life.
Application
Processors
The processing architecture of the NEAX2000 IVS 2 allows the system to be
configured with Application Processors that provide processing capacity for a specific
application or multiple applications. These EPROM-based processors support
applications such as:
•
Open Applications Interface (OAI) which connects to outboard computing
devices to support a wide range of host computer-supported features.
•
ACD Processor for call center applications.
•
Hotel Processor for Hospitality applications.
This same processor is used for SMDR for call accounting, and Message Center
Interface (MCI)
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 5
Software Architecture
Chapter 1 Introduction
Feature Packages
The NEAX2000 IVS2 introduces a new software and hardware approach, which is
designed with modularity in mind. This approach allows customers a greater degree of
cost control for new installations and for upgrades.
Feature Package
Designations
The NEAX2000 IVS 2 basic operation requires Basic Business/HM Software. In
addition to the Basic Software there are several Feature Packages, each for Business or
Hotel applications. Their applications and feature package numbers are listed below:
DESCRIPTION
DESCRIPTION
24 Port Basic System Package
• ICS VS PIMF (UA)
• ICS VS Base/Top-UB
• SPN-CP14 MP (UA)
Business/Hotel/Motel Features and Generic 2000 Load for 24 Ports.
1 per System required, supports 1 T1/E1 interface
48 Port System Software 2000 Series (FD)
Basic Business/Hotel/Motel Features and Generic 2000 Load for 48 Ports.
Provides support for 48 LT Ports, 5 T1s, ISDN, 3 Remote PIMs, 5 ISDN-PRI
DCHs, 48ISDN-BRI Trunk Spans, 128 BRI Station Ports
EXPANSION KEY (FD)
Parent Part Number that includes selected Capacity Options below
LT PORTS (48 to 128)
Expands LT Port Capacity from 48 Ports to 128 Ports
LT PORTS (48 to 256)
Expands LT Port Capacity from 48 Ports to 256 Ports
LT PORTS (48 to 512)
Expands LT Port Capacity from 48 Ports to 512 Ports
LT PORTS (128 to 256)
Expands LT Port Capacity from 128 Ports to 256 Ports
LT PORTS (128 to 512)
Expands LT Port Capacity from 128 Ports to 512 Ports
LT PORTS (256 to 512)
Expands LT Port Capacity from 256 Ports to 512 Ports
DTI SPANS (5 to 11)
Expands DTI Capacity from 5-Spans to 10.5-Spans
REMOTE PIMs (3 to 6)
Expands Remote PIM capacity from 3 to 6 Remote PIMs
ISDN-DCH LINK (5 to 8)
Expands ISDN-DCH capacity from 5 to 8 D-Channels
(PRI/DCHQ/DCH-QSIG
CCIS LINK (0 to 1)
Expands CCIS CCH capacity from 0-Links to 1-Link
CCIS LINK (0 to 4)
Expands CCIS CCH capacity from 0-Links to 4-Links
CCIS LINK (0 to 8)
Expands CCIS CCH capacity from 0-Links to 8-Links
CCIS LINK (1 to 4)
Expands CCIS CCH capacity from 1-Link to 4-Links
CCIS LINK (1 to 8)
Expands CCIS CCH capacity from 1-Link to 8-Links
CCIS LINK (4 to 8)
Expands CCIS CCH capacity from 4-Links to 8-Links
Ext. FCCS LINK (0 to 1)
Expands FCCS Link capacity from 0-Links to 1-Link
WIRELESS DEMO
Provides Capacity support for 2-ZTs & 4-PSs
WIRELESS
Provides Capacity support for 128-ZTs & 255-PSs
IPT x 1
Expands IP Trunk capacity from 0 to 1 (max. 16 channels)
IPT x 2
Expands IP Trunk capacity from 0 to 2 (max. 32 channels)
IPT x 4
Expands IP Trunk capacity to 4 IPT (max 64 channels)
IPT x 8
Expands IP Trunk capacity to 8 IPT (max 128 channels)
Page 6
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 1 Introduction
Advantages
Software
Licensing
Each system is accompanied by an NEC Customer Software License Agreement. This
agreement grants the customer a non-exclusive license to use the software (including
any related documentation and any upgrades and enhancements to the system
software) for the useful life of the system solely to operate and maintain the system
purchased under the agreement.
Integration
In addition to the application processors manufactured by NEC, the NEAX2000 IVS 2
also delivers an open architecture for integration with other manufacturers’
application processors. This integration is supported by interface processors and
specifications for communicating with computing devices such as network and
facilities management, call center applications, call accounting, property management,
voice mail, and management information systems for ACD reports and monitoring, as
well as maintenance access terminals.
Advantages
The NEAX2000 IVS 2 provides a unique set of advantages to users who seek an
advanced information system that is both flexible and dependable. Through the use of
state-of-the-art computer controlled telecommunications technology, NEC is able to
provide the following advantages:
1. Full-Featured System - NEAX2000 IVS2 station users have access to more than
300 service features that enhance user productivity, reduce operating costs, and
improve communication efficiency. In addition, the control, network and interface
positions of the NEAX2000 IVS2 can accommodate features, services and subsystems as required by specific applications.
2. Network Integration - The NEAX2000 IVS2 offers business, industries, hospitals
and hotel/motels the ability to access an extensive array of information processing
and management services by serving as the central controller of an integrated
information network. The NEAX2000 IVS 2 reflects the philosophy of NEC
Corporation to integrate C&C technology, and can provide many voice and
non-voice services.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 7
Advantages
Chapter 1 Introduction
3. Flexible Line Size-Innovative Modular hardware and software design allows the
NEAX2000 IVS2 to efficiently serve from 24 ports up to 512 ports. Modularity
gives the system the ability to expand from its minimum configuration to its
maximum capacity as the need arises. This unique expansion capability allows the
system to grow in a cost affective manner as the user requirements expand. Your
initial system investment is protected through growth capability.
4. Energy Saving and Space Savings - Through employment of state-of-the-art
technology in the system circuitry design, NEC has been able to reduce power
consumption. As a result, the current consumption of the system has been reduced
to 50% of that of any conventional electronic PBX systems. This energy saving
oriented system design allows for the use of much smaller capacity main power
equipment and air conditioning equipment. In parallel with the energy savings, the
space requirement for the system has been reduced to one third when compared
with that of a conventional electronic PBX system.
5. Building Block Configuration - In a conventional switching system, various kinds
of equipment are mounted in a cabinet group and are connected to each other by
use of connecting cables. The NEAX2000 IVS2, however, uses a building block
modular design. When installing the system, the required blocks are placed on top
of each other in a building block formation and interconnected by round bus
cables.
6. Flexible Interface Ports - The NEAX2000 IVS2 employs a Universal Port
architecture that has the flexibility to accommodate station terminal equipment,
trunks and adjunct processors. This universality allows the NEAX2000 IVS2 to
maximize slot space use and lower expansion costs.
7. High Reliability - The NEAX2000 IVS2 is designed and manufactured to provide
the highest level of system reliability. The NEAX2000 IVS2 is designed with such
features as: remote maintenance, distributed call processing, error-correcting
memory, battery backup, and automatic system alarm indications to ensure
unsurpassed reliability. Only the finest components have been used. In addition,
through the employment of LSI and custom LSI and VLSI technology, the
number of component parts has been greatly reduced, thus lessening possible
failures and insuring continuous operation.
8. Intelligent Attendant Console - The NEAX2000 IVS2 attendant console, SN716
Desk Console, is a compact, desktop unit equipped with non-locking keys, Light
Emitting Diodes, and a 4 x 40 character Liquid Crystal Display.
Page 8
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 1 Introduction
Advantages
The LED's provide continuous information relative to the status of calls in
progress. The display provides station and trunk identification, class of service
and the number of calls waiting. The LCD changes with different call states and
instructs the user which Multifunction keys are available for each state. Keys such
as Busy Verify, DND Override, etc. only appear when needed. The Multi-function
Keys reduce the number of different buttons and greatly simply operation.
9. Intelligent Digital Multifunction Terminal - In addition to supporting
conventional station equipment, the NEAX2000 IVS2 can be equipped with the
Dterm series digital electronic multifunction terminals. The Dterm terminals are
intelligent microprocessor controlled terminals, which enhance the feature
capabilities offered by the system and provide the service of conventional key
telephones over 1-pair wiring. The D term instrument may be equipped with an
interface adapter to allow simultaneous voice and data switching, without
compromising the voice communication system.
10. Ease of Installation - Because the NEAX2000 IVS2 uses pre-assembled modules
and plug-in type circuits packs, it is easy to install. Wiring connections, both
internal and external, are made through simple-to-use standard plug-ended cables.
In addition, with each unit and system having been fully factory tested prior to
shipment, potential obstacles to easy installation have been held to a minimum.
11. Ease of Maintenance - Because the system is constructed with first quality
components, reliability is high and operation is trouble free. However, should a
minor fault occur, the self diagnostic programs will detect the fault, and
automatically make the needed corrections. If the problem is beyond the internal
correction capabilities of the system, the self diagnostic programs will
automatically print the nature of the fault and the involved unit is identified on the
man-machine interface equipment. The faulty plug-in unit can then be quickly
replaced with little or no interruption of service.
12. Flexible Numbering Plan - The NEAX2000 IVS2 provides flexible numbering
assignment to meet all forms of network integration service.
13. Future Capabilities - Because the NEAX2000 IVS2 uses a stored program control,
performance enhancements and new features can be easily incorporated by simple
changes in software. The NEAX2000 IVS2 can be upgraded by using the most
current software release and, when necessary, additional hardware. This means
that the system will not become obsolete.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 9
Advantages
Chapter 1 Introduction
14. Cost Controls - With telecommunications costs growing, it is becoming
increasingly important to control them. The NEAX2000 IVS2 makes it possible
for you to get a firm grasp on telecommunications costs. Through the use of such
features as least cost routing, class of service and detail call recording, cost
reduction and control are possible.
Hardware Design
The NEAX2000 IVS2 hardware is designed to meet the following parameters:
•
Flexibility
•
Capacity
•
Reliability
•
Optimum space use
•
Minimal environmental requirements
•
Ease of installation and maintenance
A unique modular design is employed throughout the NEAX2000 IVS2. As additional
equipment modules are required, they are stacked on top of each other, rather than
mounting the equipment in conventional frames or cabinets. This innovative method
reduces installation time, avoids the use of bulky frames and provides for manageable
future expansion, virtually eliminating the possibility of outgrowing your
NEAX2000 IVS2.
Page 10
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 2
System Configuration
The NEAX2000 IVS2 consists of 1 to 8 Port Interface Modules (PIMs), each PIM will
support up to 64 interface ports to give a maximum capacity of 512 ports per system.
The PIMs are all the same with a universal back plane, which accommodates station
ports, trunk ports, I/O processors, and power supply boards. Each PIM measures 16.9
inches across by 16.4 inches high by 8.8 inches deep (includes front cover). This
compact frame allows the system to be mounted on a wall, in a 19 inch rack, on a
desk/bench, or bolted to the floor.
PIM units contain the following components.
1. Line/Trunk Interface Slots
Line and trunk interface slots house the digital and analog interface cards. The
NEAX2000 IVS2 uses the PIM-F.
•
The PIM-F has 15 slots. 12 slots (LT00-LT11) each can be used for either LT
or AP cards. 1 dedicated slot (MP12) for MP or FP, 1 dedicated slot (PFT) for
Power Failure Transfer card, and 1 dedicated slot (VM) for voice mail card. 8
port Line/Trunk cards can be mounted in LT00 to LT07 slots. 4 port
Line/Trunk cards can be mounted in LT00 to LT10 slots. LT11 slot is
available for 4 port Line/Trunk cards only when the system is configured with
two or less PIMs.
2. Power Supply Board
Each PIM is equipped with a Main Power Supply card (PZ-PW121) which
converts AC120V/240V (50Hz/60Hz) to -27V DC (4.4A), +5V (7.2A), CR
(38mA), +90V (80MA).
3. Application Processor (AP) and Common Control Slots
Application processor cards use AP slots in each PIM. The number of available
AP slots depends on the PIM number and which common control cards are needed
for that PIM. The PIM-F has up to 12 AP slots. AP Slots are used to house the
processor boards for SMDR, OAI, T1, ISDN, CCIS, and others. Common control
cards such as the CPU, Bus cards, and local processors occupy only a set number
of AP slots.
4. Power Failure Transfer (PFT)
Two methods are used to provide Power Failure Transfer: (1) Using the
designated circuit card (PZ-8PFTB) which mounts in PFT slot of each PIM to
provide up to 64 trunk to station switch over points and (2) Utilizing the front
edge cable and connecting between 4COT card and AUC card.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 11
Module Configuration
Chapter 2 System Configuration
Module Configuration
PIM (3)
PIM (2)
PIM (2)
PIM (1)
PIM (1)
PIM (1)
PIM (0)
PIM (0)
PIM (0)
PIM (0)
BASE
1 PIM (64 ports)
BASE
2 PIM (128 ports)
BASE
3 PIM (192 ports)
BASE
4 PIM (256 ports)
PIM (3)
PIM (3)
PIM (2)
PIM (2)
PIM (1)
PIM (1)
PIM (5)
PIM (0)
PIM (4)
PIM (0)
PIM (4)
BASE
BASE
5 PIM (320 ports)
BASE
BASE
6 PIM (384 ports)
PIM (3)
PIM (3)
PIM (7)
PIM (2)
PIM (6)
PIM (2)
PIM (6)
PIM (1)
PIM (5)
PIM (1)
PIM (5)
PIM (0)
PIM (4)
PIM (0)
PIM (4)
BASE
BASE
7 PIM (448 ports)
Page 12
BASE
BASE
8 PIM (512 ports)
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 2 System Configuration
Installation Methods
Installation Methods
The NEAX2000 IVS2 provides three installation methods as follows:
•
Floor Standing Installation
•
Wall Mounting Installation
•
19-inch Rack Mounting Installation
Figure 2-1 Floor Standing Installation
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 13
Installation Methods
Chapter 2 System Configuration
Figure 2-2 Wall-Mounting Installation
Figure 2-3 Rack Mounting Installation
Page 14
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 2 System Configuration
Technical Terms
Technical Terms
SYMBOL
DESCRIPTION
SYMBOL
AMP
Amplifier Trunk Card
AP00
SMDR/Hotel Application Card
AP01
OAI Interface Card
LDT
LD Trunk Card
AUC
Analog Universal Circuit Card
(Long Line Circuit, DID Trunk)
M03
V.35 DTE Interface Card
BGM
External Music Source for Dterm
Back Ground Music Service
M10
Optical Interface Card
BRT
Basic Rate Interface Trunk Card
MAT
Maintenance Administration Terminal
CCH
Common Channel Handler Card
MDF
Main Distribution Frame
CFT
6/10 Party Conference Trunk Card
MEM
Main Memory
CIS
Call Information System
MFR
MF Receiver/ MFC
Receiver/Sender Card
CIR
CALLER ID Receiver Trunk Card
COT
C.O. Trunk Card
CSI
CS/ZT Interface Card
MP
Main Processor Card
Cell Station (For Australia/Others) Zone
Transceiver (For North America/ Latin
America)
PFT
Power Failure Transfer
DAT
Digital Announcement Trunk Card
PMS
Property Management System
DCH
D-channel Handler Card
OAI
Open Application Interface
DIT
DID Trunk Card
ODT
OD Trunk Card (2/4 wire E&M)
DK
External Relay/Key Interface Card
PBR
PB Receiver Card
DLC
Digital Line Circuit Card
(for Dterm, ATTCON, DESKCON)
PBSND
DPC
Data Port Controller Card
DSS
DSS Console
DTE
Data Terminal Equipment
DTI
Digital Trunk Interface Card
SMDR
Station Message Detail Recording
DTG
Digital Tone Generator
TDSW
Time Division Switch
ETHER
Ethernet Control Card
TNT
Tone/Music Source Interface Card
VCT
CODEC Card
VM
Voice Mail Card
CS/ZT
EXPMEM Memory Expansion Card
ICH
ISDN-channel Handler Card
ILC
ISDN Line Circuit Card
IPT
IP Trunk Card
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
KEY
DESCRIPTION
LC
MLDT
MODEM
PLO
PS
PRT
16CFT
KEY
External Key
Line Circuit Card
(for Single Line Telephone)
Melody Trunk
Modem
PB Sender
Phase Locked Oscillator
Personal Station
ISDN Primary Rate Interface Trunk Card
16 Circuit Four Party Conference Trunk
External Key
Page 15
Trunking Diagram
Chapter 2 System Configuration
Trunking Diagram
This figure shows a typical trunking diagram of the NEAX2000 IVS2 system.
Page 16
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 2 System Configuration
Layout of PIM (SN1480 PIMF)
Layout of PIM (SN1480 PIMF)
The NEAX2000 IVS2 consists of Port Interface Modules (PIMs) which contain lines,
trunks, interfaces, switching circuitry, control processors and power equipment. The
following diagrams show the physical layout of elements within the PIM.
LT00-LT11: Line/Trunk card
mounting slots
VM: PZ-VM00-M mounting slot
System Capacity for Line/Trunk Card
Max. 64 ports per PIM
Max. 512 ports per system
AP00-AP11:
Application Processor card mounting
slots
PFT: PZ-8PFTB mounting slot
System Capacity for Application
Processor Card
Max. 24 cards per system
Max. 256 ports per system
MP: PN-CP14 mounting slot
AC/DC PWR: PZ-PW121 mounting slot
FP: PN-CP15 mounting slots
DC/DC PWR: PZ PW122 mounting slot
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 17
Control Card Mounting Conditions
Chapter 2 System Configuration
Control Card Mounting Conditions
1. PN-CP14 (MP)
Mount the PN-CP14 card in the MP slot (Slot 12) of PIM0.
2. PN-CP15 (FP)
When the system is configured with three PIMs or more, mount one PN-CP15
card in the FP slot, PIM 0: Slot 11 and PIM 2, 4, 6: Slot 12. When the system is
configured with one or two PIMs, the PN-CP15 card does not need to be mounted.
PIM 3
PIM 7
PIM 2
PIM 6
PIM 1
PIM 5
PIM 0
PIM 4
Figure 2-4 MP/FP Card Mounting Slots
Page 18
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 3
Terminals
The NEAX2000 IVS2 can accommodate both Dterm Series III and Dterm Series E
terminals to provide a variety of desktop solutions. In addition to the Dterm Series III/E
terminals, the SN716 DESKCON is used for the Attendant Answering Position.
Dterm Series III
The D term Series III terminals are intelligent, microprocessor-controlled,
multi-function telephones that enhance the feature capabilities offered by the system.
They provide access to sophisticated features, beyond those of conventional key
telephones, over one-pair wiring.
Advantages of
Dterm Series III
In physical operation, as well as functionally, the Dterm Series III terminals assure
effortless, comfortable handling.
•
Call Indicator Lamp
When a call comes in, a small but highly visible light on the corner of the terminal
flashes. Because the light can be seen from every direction, it helps assure that the
user won't miss important calls.
•
Electronic Volume Control
A single set of control keys for adjusting LCD contrast, speaker/receiver volume,
and ringer volume is located on the front panel of the terminal. These universal
keys increase operational efficiency and eliminate the need to have a number of
different volume control keys.
•
Tilt-Up Legs
The terminal adjusts to the user's operating environment. Information on the LCD
screen is easy to see, and key operations are more comfortable.
•
Programmable Line Keys and Dedicated Feature Keys
Dterm Series III terminals offer 8- or 16-line keys with dual-color LEDs for line
status indication. Line keys are flexible for line, trunk or feature access. This flexibility allows the terminal to fit the user's individual needs. Call screening functions between executives and secretaries, call pickup to another station, message
waiting indication of voice mail and fax arrival indication can all be programmed
on the line keys of the terminal.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 19
Dterm Series III
Dedicated Feature
Keys
Dterm Series III
Accessories
Chapter 3 Terminals
•
40-Character Display
For better call handling, the Dterm Series III terminals with 16 line keys feature an
easy-to-read, 20-character, 2-line LCD screen. The LCD screen provides information on calling number with name, call back message, return schedule messages,
dialed digit information, service feature indications, called station status, and
elapsed call time.
•
Hands-free Operation
Dterm Series III terminals offer hands-free operation as a standard feature. The
built-in microphone and speaker let users keep their hands available for work
while speaking on the phone.
•
ANSWER: Answers any incoming ringing call
•
CONFERENCE: Simplifies access to Three-way Calling
•
DOWN/UP: Controls speaker/handset volume, display contrast, ringer volume
•
FUNCTION: Provides special functions (ex; MIC-ON/OFF, COT gain control)
•
HOLD: Provides Exclusive and Non-Exclusive Hold of line appearances
•
LAST NUMBER REDIAL/SPEED CALLING-STATION: Provides for Stack
Dial or Speed Calling-Station
•
RECALL: Terminates a call in progress and immediately seizes dial tone
(Line Reconnect – Same Line)
•
SPEAKER: Controls the built-in speaker which can be used for Hands-free Dialing/Monitoring and Voice Call
•
TRANSFER: Facilitates Call Transfer, Consultation Hold and Call Splitting
•
DSS/BLF Console
The Dterm Series III can be equipped with a DSS/BLF Console. This provides 48
Direct Station Selection keys which allow the user to call another station with one
touch key operation. Also, it shows the busy status of the stations assigned on
each DSS key by LED lamp indication.
The DSS/BLF Console requires an extra interface to the PABX and an AC-DC
Adapter.
Page 20
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Dterm Series III
Chapter 3 Terminals
Dterm Series III
Terminals
•
Data Adapter
For the data user, Dterm III terminals can be used to transmit digital information at
speeds up to 19.2 kbps (asynchronous or synchronous) by adding the Data
Adapter.
•
Long Line Adapter
The Long Line Adapter provides a cable length (max. 4000 feet/1200 m) between
the Main System and a Dterm III terminal.
•
Wall Mount Unit
The Wall Mount Unit allows a Dterm III to be conveniently mounted vertically
when desk space is not available.
•
Ancillary Devices Adapter
The Ancillary Devices Adapter provides Dterm III terminals with a connection for
a head set or External Hands-free Unit or provides a recording jack.
•
Analog Port Adapter
The Analog Port Adapter provides a Dterm III terminal with a connection for a PC
with a modem.
•
Analog Port Adapter with Ringing
The Analog Port Adapter with Ringing provides Dterm III terminals with a connection for a facsimile, cordless telephone, etc. The Dterm Series III family of terminals is shown following. These multiline Digital Terminals are available in soft
white (SW) or in black.
The following illustrations show the features and accessories of the Dterm systems.
•
2 dedicated functions keys
•
8 additional programmable feature keys
•
call/message indicator
Figure 3-1 Dterm S IIID SLT (ETJ-1DT-1) - Single Line Digital Instrument
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 21
Dterm Series III
Chapter 3 Terminals
•
8 dedicated function keys
•
hands-free operation
•
call/message indicator
•
tilt leg
Figure 3-2 Dterm 8 (ETJ-8-1) - 8 Button Digital Instrument without LCD Display
•
8 dedicated function keys
•
8 line/feature access keys
•
40 character, 2 lines LCD display
•
call/message indicator
•
tilt leg
Figure 3-3 Dterm 8IS (ETJ-8IS-1)
•
8 dedicated function keys
•
16 line/feature access keys
•
40 character, 2 lines LCD display
•
hands-free operation
•
call/message indicator
•
tilt leg
Figure 3-4 Dterm 16DC (ETJ-16DC-1)
Page 22
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Dterm Series III
Chapter 3 Terminals
•
8 dedicated function keys
•
16 line/feature access keys
•
40 character, 2 lines LCD display
•
20 additional programmable
feature keys
•
hands-free operation
•
call/message indicator
•
tilt leg
Figure 3-5 Dterm 16DD (ETJ-16DD-I)
•
8 dedicated function keys
•
24 line/feature access keys
•
40 character, 2 lines LCD display
•
12 additional programmable
feature keys
•
hands-free operation
•
call/message indicator
•
tilt leg
Figure 3-6 Dterm 24DS (ETJ-24DS-1)
•
2 dedicated function keys
•
call/message indicator
Figure 3-7 Dterm Series IIIA (ETJ-1-1) - Single Line Analog Telephone
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 23
Dterm Series III
Chapter 3 Terminals
•
2 dedicated function keys
•
8 additional programmable feature
keys
•
call/message indicator
Figure 3-8 Dterm Series IIIH (ETJ-1HM) - Single Line Analog Telephone with
8 Speed Dial Keys
•
48/60 Direct Station Selector/Busy
Lamp Field
•
Add-On Module for Dterm Series III
Figure 3-9 EDW-48-2 DSS/BLF
Figure 3-10 Typical Dterm III Adapters - ADA-J, APA-J, APR-J, LLA-J and CTA-J
Page 24
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Dterm Series III
Chapter 3 Terminals
Line Conditions of
Each Dterm
Series III Terminal
The cable length between the DLC card and terminal varies depending on the type of
terminal. This table shows the line conditions of each Dterm and DSS/BLF Console.
Table 3-1
TERMINAL TYPE
Dterm Series III (8 button)
Dterm Series III
(16 button)
Dterm Series III
(24 button)
DSS/BLF Console
Note 2
Line Conditions of Each Dterm Series III Terminal
CARD TYPE
CABLE LENGTH*
(CABLE 0.5φ
φ /24 AWG)
PN-8DLCL/8DLCP
(STANDARD)
984 ft.
PN-4DLCM/4DLCQ
(STANDARD)
984 ft. (300 m)
[3937 ft. (1200 m)]
PN-2DLCB/2DLCN
(LONG)
2788 ft. (850 m)
[3937 ft. (1200 m)]
PN-8DLCL/8DLCP
(STANDARD)
492 ft. (150 m)
PN-4DLCM/4DLCQ
(STANDARD)
492 ft. (150 m)
[3937 ft. (1200 m)]
PN-2DLCB/2DLCN
(LONG)
2788 ft. (850 m)
[3937 ft. (1200 m)]
PN-8DLCL/8DLCP
(STANDARD)
492 ft. (150 m)
PN-4DLCM/4DLCQ
(STANDARD)
492 ft. (150 m)
[3937 ft. (1200 m)]
PN-2DLCB/2DLCN
(LONG)
2788 ft. (850 m)
[3937 ft. (1200 m)]
PN-8DLCL/8DLCP
(STANDARD)
984 ft.
(300 m)
PN-4DLCM/4DLCQ
(STANDARD)
984 ft.
(300 m)
PN-2DLCB/2DLCN
(LONG)
2788 ft.
REMARKS
(300 m)
Note 1
Note 1
Note 1
Note 1
(850 m)
*The value in brackets [ ] shows the cable length when local power is supplied.
Note 1: When using PN-8DLCL or PN-8DLCP card, the long-line function is not available, even if Dterm is
equipped with Long Line Adapter.
Note 2: The DSS/BLF Console requires local AC/DC power supply.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 25
Dterm Series E
Chapter 3 Terminals
Dterm Series E
The Dterm Series E line of telephone terminals is strategically designed to provide
ergonomically form and user-friendly functions. With advanced digital circuitry, the
Dterm Series E terminals consist of six distinct models to meet users' diverse telephone
terminal needs. The new Dterm Series E family of terminals offers adjustable display
and non-display units with menu-driven soft key operation, allowing users to program
terminals at the desktop. The display units are equipped with large LCD panels, which
can carry 24 characters via three lines of display. Each terminal offers full duplex
speaker phone operation for two-way conversation. Standard features include headset
jacks, wall mount units and adjustable base units.
Features
Page 26
•
Built-in LLA function
•
Four Local Soft Key Controls (Detail functions are depending on PBX.)
•
Large Message Waiting LED
•
24 Character, 3 line LCD
•
Tilt & Detachable LCD Unit
•
Adjustable legs
•
Built-in Wall Mount Unit
•
Built-in Headset Jack connector
•
Speed Dial/DSS Buttons
•
Programmable Line Keys with 2 color LED
•
Eight dedicated function keys (Feature, Recall, Conf, Redial, Hold, Transfer,
Answer, & Speaker)
•
Built-in Half Duplex Handsfree unit
•
Optional: Full Duplex HFU (consist of HFU-U Unit, External Microphone Unit
and AC adapter)
•
Snap-in Options available:
•
Ancillary Device Adapter (ADA-U)
•
Analog Port Adapter (APA-U)
•
Analog Port Adapter with Ringing (APR-U) External Wallmount Unit
(WMU-U)
•
AC Adapter Unit (ACA-U)
•
CTI Adapter (CTA-U)
•
External Handsfree Unit, includes an External Microphone (HFU-U)
•
Directory Designation Card Holder (DCU-U)
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Dterm Series E
Chapter 3 Terminals
Dterm Series E
Terminals
The following illustrations shows the Dterm Series E family of terminals.
This digital Multiline Terminal is equipped with 8 programmable line keys
(each with a two-color LED), built-in speakerphone, ADA compatibility, and
a large LED to indicate incoming calls and messages.
This terminal comes in two colors: black (BK) and white (WH).
Figure 3-11 DTP-8-1
This digital Multiline Terminal is equipped with 8 programmable line keys
(each with a two-color LED), built-in speakerphone, ADA compatibility, and
a large LED to indicate incoming calls and messages.
This terminal is also equipped with a 24-character, 3-line, adjustable Liquid
Crystal Display (LCD). It also provides four soft keys.
This terminal comes in two colors: black (BK) and white (WH).
Figure 3-12 DTP-8D-1
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 27
Dterm Series E
Chapter 3 Terminals
This digital Multiline Terminal is equipped with 16 programmable line keys
(each with a two-color LED), a built-in speakerphone, ADA compatibility,
and a large LED to indicate incoming calls and messages.
This terminal is also equipped with a 24-character, 3-line, adjustable Liquid
Crystal Display (LCD). It also provides four soft keys.
This terminal comes in two colors: black (BK) and white (WH).
Figure 3-13 DTP-16D-1
This digital Multiline Terminal is equipped with 32 programmable line keys
(each with a two-color LED), a built-in speakerphone, ADA compatibility,
and a large LED to indicate incoming calls and messages.
This terminal is also equipped with a 24-character, 3-line, adjustable Liquid
Crystal Display (LCD). It also provides four soft keys.
This terminal comes in two colors: black (BK) and white (WH).
Figure 3-14 DTP-32D-1
Page 28
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Dterm Series E
Chapter 3 Terminals
This digital terminal has 2 Flexible line/Feature Access keys, 8 dedicated
Function Keys, Handsfree Speakerphone Operation (Half Duplex), Large
Call/Message indicator and optional Wall Mount Unit (730112). This
terminal has no built-in LLA.
This terminal comes in White (WH) only.
Figure 3-15 DTP-2DT-1 (WH) TEL
This Console is equipped with 60 programmable line keys (each with a
two-color LED). These keys can be programmed as Direct Station keys,
function keys, or outside line keys. It interfaces to the NEAX1000 system via
existing 4DLC cards and the new 8DLCH card and uses single pair cabling.
This console comes in two colors: Black (BK) and Ivory White (WH).
Figure 3-16 DCU-60-1 Console
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 29
Dterm Series E
Line Conditions of
Each Dterm
Series E Terminal
Chapter 3 Terminals
The cable length between the DLC card and terminal varies depending on the type of
terminal. This table shows the line conditions of each Dterm and DSS/BLF Console.
Table 3-2
TERMINAL TYPE
Dterm Series E
(8 button)
Dterm Series E
(16 button)
Dterm Series E
(32 button)
DSS/BLF Console
Note 2
Line Conditions of Each Dterm Series E Terminal
CARD TYPE
CABLE LENGTH*
(CABLE 0.5φ
φ /24 AWG)
PN-8DLCL/8DLCP
(STANDARD)
984 ft.
(300 m)
PN-4DLCM/4DLCQ
(STANDARD)
984 ft. (300 m)
[3937 ft. (1200 m)]
PN-2DLCB/2DLCN
(LONG)
2788 ft. (850 m)
[3937 ft. (1200 m)]
PN-8DLCL/8DLCP
(STANDARD)
656 ft.
PN-4DLCM/4DLCQ
(STANDARD)
656 ft. (200 m)
[3937 ft. (1200 m)]
PN-2DLCB/2DLCN
(LONG)
2788 ft. (850 m)
[3937 ft. (1200 m)]
PN-8DLCL/8DLCP
(STANDARD)
656 ft.
PN-4DLCM/4DLCQ
(STANDARD)
656 ft. (200 m)
[3937 ft. (1200 m)]
PN-2DLCB/2DLCN
(LONG)
2788 ft. (850 m)
[3937 ft. (1200 m)]
PN-8DLCL/8DLCP
(STANDARD)
984 ft.
(300 m)
PN-4DLCM/4DLCQ
(STANDARD)
984 ft.
(300 m)
PN-2DLCB/2DLCN
(LONG)
2788 ft.
(200 m)
(200 m)
REMARKS
Note 1
Note 1
Note 1
Note 1
(850 m)
*The value in brackets [ ] shows the cable length when local power is supplied.
Note 1: When using PN-8DLCL or PN-8DLCP card, the long line function is not available, even if Dterm is
equipped with Long Line Adapter.
Note 2: The DSS/BLF Console requires local AC/DC power supply.
Page 30
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 3 Terminals
SN716 DESKCON
SN716 DESKCON
The SN716 Desk Console has an ergonomic design and provides full access to all
PBX Console features. It connects to the NEAX2000 IVS2 using the same circuit
cards as the Dterm Series E and Series III terminals. The SN716 Desk Console has
ATT Interface (ATI) to connect to the PBX. This interface is 6-core Modular Jack;
inner 1 pair for signal and outer 2 pairs are for power supply.
The SN716 Desk Console operates on a switched-loop basis with a maximum of 6
Attendant loops terminating at each console on the associated Interface card. The
Attendant uses these loops for answering, originating, holding, extending, and
reentering calls. When Attendant loop release is used, the number of loops is
effectively increased to a maximum of 12 for each console.
The NEAX2000 IVS2 supports a maximum of eight SN716 DESK Consoles.
Figure 3-17 SN716 DESKCON
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 31
SN716 DESKCON
SN716 DESKCON
Features
Line Conditions of
the SN716
DESKCON
Chapter 3 Terminals
•
Character LCD (4x40 characters)
•
LCD designation strips
•
Software-controlled LCD loop key
•
Full access to PBX features
•
Headset connectivity
•
Recorder connectivity
The cable length between the DLC card and terminal varies depending on the type of
terminal. Table 3-1 shows the line conditions of the Attendant Console.
Table 3-1
TERMINAL TYPE
SN716
DESKCON
Page 32
Line Conditions of the SN716 DESKCON
CARD TYPE
CABLE LENGTH*
(CABLE 0.5 φ /24
AWG)
PN-8DLCL/8DLCP And
PN-PW00 or AC Adapter
1000 ft.
(304 m)
PN-4DLCM/4DLCQ and
PN-PW00 or AC Adapter
1500 ft.
(457 m)
REMARKS
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 4
Equipment Description
Modules
EQUIPMENT NAME
FUNCTIONAL NAME
IVS VS PIMF (UA)
PIM
ICS VS BASE (UA)
BASE/TOP ASSEM
ICS VS BATT (UA)
BATTM
FUNCTION
Port Interface Module (PIM)
Base/Top Cover Assembly
Battery Module for housing PIM
or CS (ZT) backup batteries
Installation Hardware
EQUIPMENT NAME
FUNCTION
HANGER ASSEM (B)
Wall Hanger Assembly
MOUNTING BRACKET
Safety Mounting Bracket
19" RACK BRACKET (A)
19-inch Rack Mounting Bracket Type A
19" RACK BRACKET (B)
19-inch Rack Mounting Bracket Type B
I/F BRACKET ASSEM
Inter Frame Bracket Assembly
BASE TRAY ASSEM
Base Tray Assembly
Common Control
EQUIPMENT NAME
PN-CP14
FUNCTIONAL NAME
FUNCTION
MP
Main Processor & BUS interface
for PIM 0 to PIM 1
FP
Firmware Processor & BUS
interface for PIM Expansion
EXPMEM
Memory Expansion Card for
MP/AP00 Card
PN-PW00
EXTPWR
Power Supply card for DESKCON
PZ-PW121
AC/DC PWR
Main Power Supply card
DC/DC PWR
Power Supply card for Cell Station
(Zone Transceiver)
PN-CP15
PZ-M537
PZ-PW122
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 33
Analog C.O. Trunk
Chapter 4 Equipment Description
Analog C.O. Trunk
EQUIPMENT
NAME
FUNCTIONAL
NAME
FUNCTION
PN-4COTB
COT
4-line Central Office Trunk Card (Ground Start
Trunk)
PN-4COTG
COT
4-line Central Office Trunk Card (Loop Start
trunk)
PN-8COTS
COT
8-line Central Office Trunk Card (Ground Start
Trunk)
PN-8COTQ
COT
8-line Central Office Trunk Card (Loop Start
Trunk)
Analog DID Trunk
EQUIPMENT
NAME
FUNCTIONAL
NAME
FUNCTION
PN-AUCA
AUC
2-line Analog Long Line Circuit Card provided
with Power Failure Transfer (PFT) Function, or
2-line Direct Inward Dialing Trunk Card
PN-4DITB
DIT
4-line Direct Inward Dialing Trunk Card
Analog Tie Line Trunk
EQUIPMENT
NAME
PN-2ODTA
FUNCTIONAL
NAME
ODT
FUNCTION
2-line Out Band Dialing Trunk Card
Analog Station
Page 34
EQUIPMENT
NAME
FUNCTIONAL
NAME
PN-4LCD-A
LC
4-Line Analog Line Circuit Card for Single Line
Telephones
PN-8LCAA
LC
8-line Analog Line Circuit Card for Single Line
Telephones
PN-AUCA
AUC
2-line Analog Long Line Circuit Card provided
with Power Failure Transfer (PFT) Function, or
2-line Direct Inward Dialing Trunk Card
FUNCTION
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 4 Equipment Description
Digital Station
Digital Station
EQUIPMENT
NAME
FUNCTIONAL
NAME
PN-2DLCB/
PN-2DLCN
DLC
2-line Digital Long Line Circuit Card for
Dterm Series E/III, Elite, Electra Pro,
DSS Console, DESKCON
PN-4DLCM
DLC
4-line Digital Line Circuit Card for
Dterm Series E/III, Elite, Electra Pro,
DSS Console, DESKCON
PN-4DLCQ
DLC
4-line Digital Line Circuit Card for
Dterm Series E/III, DSS Console, DESKCON
PN-8DLCP
DLC
8-line Digital Line Circuit Card for
Dterm Series E/III, DSS Console, DESKCON
FUNCTION
Digital Trunk
EQUIPMENT
NAME
FUNCTIONAL
NAME
PN-24DTA-C
DTI
Digital Trunk Interface (23B+D, 1.5 Mbps) Card
(T1)
PN-30DTC-A
DTI
Digital Trunk Interface (2 Mbps) Card (E1)
FUNCTION
Data
EQUIPMENT
NAME
FUNCTIONAL
NAME
FUNCTION
PN-2DPCB
DPC
2-line Data Port Controller Card for 48K,
64 Kbps, V110, V11
SPN-V35
ADP
V.35 Data Terminal Equipment Interface Card
CCIS
EQUIPMENT
NAME
FUNCTIONAL
NAME
PN-24DTA-C
DTI
Digital Trunk Interface (23B+D, 1.5 Mbps) Card
(T1)
PN-SC00
CCH
Common Channel Handler Card
PN-30DTC-A
DTI
Digital Trunk Interface (2 Mbps) Card (E1)
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
FUNCTION
Page 35
ISDN/ECCIS
Chapter 4 Equipment Description
ISDN/ECCIS
EQUIPMENT
NAME
FUNCTIONAL
NAME
FUNCTION
PN-BRTA
BRT
1-line Basic Rate (2B+D) Interface Trunk card
PN-2BRTC
BRT
2-line Basic Rate (2B+D) Interface Trunk card
PN-2ILCA
ILC
2-line BRI Station card
PN-SC03
8ICH
BRI (station), one 8ICH needed for every four
2ILCA cards
DTI
Digital Trunk Interface (23B+D, 1.5Mbps)
Card (T1)
PRT
ISDN Primary Rate (23B+D) Interface Card
(Built-in D-Channel)
PN-SC01
DCH
D-channel Handler Card
SPN-SC01
QSIG
QSIG Protocol Handler
PN-24DTA-C
PN-24PRTA
IP Trunk
EQUIPMENT
NAME
FUNCTIONAL
NAME
FUNCTION
PN-IPTA
IPT
IP Trunk Interface card (16 ch)
PN-4VCTH
VCT
4-channel CODEC Card for IP Trunk
Registers
EQUIPMENT
NAME
PN-8RSTA
FUNCTION
PBR
8-line PB Receiver Card
MFR
4-line MF Receiver, MFC Receiver/Sender
Card
PN-4RSTC
CIR
4-line Caller ID Receiver Trunk Card
PN-4RSTB-911
MFR
4-line Register Sender for 911
PN-4RSTB
Page 36
FUNCTIONAL
NAME
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 4 Equipment Description
Miscellaneous Trunk
Miscellaneous Trunk
EQUIPMENT
NAME
FUNCTIONAL
NAME
FUNCTION
PN-DK00
DK
8-circuit External Relay Control/External Key
Scan Card
PN-CFTA
CFT
6/10 Party Conference Trunk Card
PN-CFTB
CFT
6 Party Conference Trunk Card
PN-2DATA
DAT
2-line Digital Announcement Trunk Card
PN-4DATC
DAT
4-line Digital Announcement Trunk Card
PZ-8PFTB
PFT
8-line Power Failure Transfer Card
PN-TNTA
TNT
2-line Tone/Music Source Interface Card
PN-2AMPA
AMP
2-line Amplifier Trunk Card
PN-CFTB
CFT
6/10 Party Conference Trunk Card
System I/O, OAI, ACD
EQUIPMENT
NAME
FUNCTIONAL
NAME
PN-AP00-B
MRC
SPN-AP01
IP
PN-CC01
ETHER
FUNCTION
Provides four RS-232C ports, and is used for
SMDR, Hotel Printer, CIS, PMS, MCI, CS report
functions.
Provides one RS-232C port and one Ethernet
interface port. Used for OAI function, ID code
expansion.
Ethernet Control Card
Voice Mail
EQUIPMENT
NAME
FUNCTIONAL
NAME
PZ-VM00-M
VM
4-port Voice Mail Card (NEAXMail AD-8)
PZ-VM01
VM
4-port Voice Mail Extension Card
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
FUNCTION
Page 37
Wireless
Chapter 4 Equipment Description
Wireless
EQUIPMENT
NAME
FUNCTIONAL
NAME
FUNCTION
PN-2CSIA
CSI
2-line Zone Transceiver Interface Card
PN-SC03-A
CSH
CS (ZT) Handler Card
PN-AP00-A
DBM
Data Base Module Card for WCS Roaming
function One card per WCS system.
SPN-SC01
DCH-Q
Q931 Protocol Handler for Wireless Roaming
Remote PIM
EQUIPMENT
NAME
FUNCTIONAL
NAME
FUNCTION
PN-DAIA
DAI
Digital Trunk Interface (23B+D, 1.5Mbps) Card
for Remote PIM
PN-DAIB
DAI
Digital Trunk Interface (23B+D, 1.5Mbps) Card
for Remote PIM
PN-DAIC
DAI
Digital Trunk Interface (23B+D, 1.5Mbps)
Channel Expansion Card for Remote PIM
PN-DAID*
DAI
Digital Trunk Interface (2Mbps) Card for Remote
PIM
PN-DAIE*
DAI
Digital Trunk Interface (2Mbps) Card for Remote
PIM
PN-DAIF*
DAI
Digital Trunk Interface (2Mbps) Channel
Expansion Card
*These cards are subject to availability.
Optical Interface
Page 38
EQUIPMENT
NAME
FUNCTIONAL
NAME
PN-M10
M10
FUNCTION
Optical Interface Card
Provides internal optical modem to T1/E1
network or Remote PIM
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5
Feature Description
Account Code
This feature, when used with Station Message Detail Recording (SMDR), allows
station users and Attendants to enter a cost accounting or client billing code (up to 16
digits) into the system.
Add-On Module
This feature allows the Add-On Module to be combined with a Multiline Terminal
when there are insufficient line or trunk keys provided at the Multiline Terminal.
When the EDW-48-2 unit keys are programmed as line/trunk keys, the additional 25
lines/trunks and the existing lines/trunks set for the Multiline Terminal can be
accessed directly (maximum of 49 lines/trunks). The station speed dialing function
can be assigned for all keys on the EDW-48-2 unit. Also, one of the last 3 keys can be
used as a Day/Night change key.
Alarm Indications
Faults are indicated by the Major/Minor (MJ/MN) lamps located on the AC/DC
Power Supply and, optionally, an external alarm display unit. Station Application not
applicable.
Alphanumeric Display
The ETJ-16DC-1 Multiline Terminals are each equipped with a 2-line, 20-character
Liquid Crystal Display (LCD). These displays are used to provide alphanumeric
information including clock/calendar and call processing information.
Station Application All Multiline Terminals with an LCD display.
Analog Port Adapter
This feature allows an APR-J or APA-J unit combined with a Multiline Terminal to
connect to an analog terminal such as an analog telephone, Modem, and PC with
built-in Modem. There are two communication modes for the terminal connected via
the Analog Port Adapter as shown below:
1. Single Port Mode
A Multiline Terminal and an analog terminal share the same port. In this mode,
the Multiline Terminal and the analog terminal cannot be used simultaneously.
2. Dual Port Mode
A Multiline Terminal and an analog terminal use different ports. In this mode, the
Multiline Terminal and the analog terminal can be used simultaneously.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 39
Announcement Service
Chapter 5 Feature Description
Announcement Service
This feature allows station users to record messages on Digital Announcement Trunk
(DAT) cards. When a station user dials the feature access code for this feature, the
user receives the corresponding message from the system.
Answer Key
An Answer Key is provided on all Multiline Terminals. The Answer Key can be used
to answer incoming calls on outside lines, and primary or secondary extensions. When
the Answer Key is used to answer an incoming call with a call in progress, the first
party is placed on hold and the second party is connected. If the Answer Key is
depressed while in a three-party call, the user can alternate between each party and a
Broker's Call is established.
Attendant Assisted Calling
This feature allows a station user to ask an Attendant for assistance in originating a
call. Three methods are available: non-delay, delay, and passing dial tone.
Attendant Camp-on
This feature permits the Attendant to hold an incoming call in a special mode when
the desired station for the transfer is busy. The Attendant sends a Camp-On tone to the
busy station. When that station becomes idle, it is automatically alerted and connected
to the waiting party.
Attendant Console
SN716 DESKCON
The Attendant Console (SN716 DESKCON) operates on a switched-loop basis with a
maximum of 6 Attendant loops terminating at each console on the associated Interface
card. The Attendant uses these loops for answering, originating, holding, extending,
and reentering calls. When Attendant loop release is used, the number of loops is
effectively increased to a maximum of 12 for each console.
Attendant
Called/Calling
Name Display
This feature provides a display of the calling/called party's name on the Attendant
Console LCD for Attendant Called/Calling Name Display. On attendant-to-station
calls, the LCD display the name assigned to the primary extension of the station. On
attendant-to-trunk calls, the LCD displays the name assigned to the trunk route of the
trunk.
Page 40
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Attendant Console
Attendant
Called/Calling
Number
This feature provides a display of the station number and station name on the
Attendant Console during an Attendant-to-station connection. During an
Attendant-to-trunk connection, the same display shows the trunk route designation
and a trunk identification code (4 digits).
Attendant Call
Selection
This feature allows assignment of keys on the Attendant Console to particular types of
trunk routes (such as WATS or FX) and particular types of service calls (such as
Attendant recalls, intercept calls, etc.). LEDs indicate the type of incoming call and
pressing the associated key allows the Attendant to answer the calls in any order.
Attendant Console
Lockout Password
This feature allows the Attendant Console to be set into a lockout mode. This disables
the console from originating or receiving calls and setting or resetting service features.
To return the Console to its manual operating condition a password is required.
Attendant Do Not
Disturb Setup And
Cancel
The Attendant has the ability to enter and remove individual stations from Do Not
Disturb (DND). Additionally, the Attendant can set one preassigned group of stations
into, or out of, Do Not Disturb.
Attendant
Interposition
Calling/Transfer
This feature allows any Attendant to directly converse with another Attendant and
also allows Attendants to transfer calls from their console to another Attendant's
console in systems where Multiple Console Operation has been provided.
Attendant Lamp
Check
This function is used to check the status of keys, lamps, and LCDs mounted on the
Attendant Console to verify that various operations of the Attendant Console are
functioning normally. The check is done by a preset procedure.
Attendant Listed
Directory Number
This feature provides a display of the Listed Directory Number on the Attendant
Console when the operator has answered a Listed Directory Number call.
Attendant Loop
Release
This feature allows an Attendant Console loop to become available for a second call
as soon as the Attendant has directed the first call to a station, even if that station does
not answer.
Attendant
Programming
This function is allowed only for the Attendant Console (SN610) and is used to
execute DISA code set up, speed dial programming, and system clock set up
operations.
Attendant Training
Jacks
The Attendant Console can be equipped with two headset/handset jacks using an
optional adapter. Two jacks are equipped on the adapter and can be used for training
new operators.
Audible Indication
Control
This feature allows the Attendant to adjust the volume of audible indications received
at the Attendant Console.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 41
Attendant Console
Chapter 5 Feature Description
Call Processing
Indication
This feature provides visual indications of all calls being processed or awaiting
processing at the Attendant Console.
Call Queuing
This feature provides the Attendant the ability to handle a series of exchange network
calls in the order of their arrival, (first in, first out) thereby eliminating unnecessary
delays.
Call Splitting
This feature allows the Attendant to confer privately with one party on an Attendant
handled connection without the other party overhearing.
Call Waiting
Display
This feature provides a visual indication to the Attendant when one or more calls are
waiting to be answered.
Common Route
Indial
This feature allows assignment of incoming DID calls to different Attendant Call
Selection keys based on the last 4 digits dialed into the system. Up to eight individual
Listed Directory Numbers can be assigned in system programming. When an
incoming call to any of these trunks is received, an Attendant Call Selection key will
flash and the LCD display will indicate the Listed Directory Number associated with
that trunk route.
Dialed Number
Identification
Service (DNIS)
This feature provides a display of the company name on the Attendant Console when
the Attendant has answered a Listed Directory Number or a Tie Line call.
Incoming Call
Identification
Incoming calls are identified by various means. Refer to Attendant Called/Calling
Number, Attendant Call Selection, Attendant Source Key, Attendant Listed Directory
Number and Common Route Indial Features and Specifications.
Individual Trunk
Access
The Attendant Console is provided with the ability to access each individual trunk by
dialing an associated identification code. This allows detection of faulty trunks during
regular testing or after complaints. The Customer Administration Terminal (CAT) or
Maintenance Administration Terminal (MAT) has the capability to then busy out the
trunk until repair is made.
Multi-Function Key
This feature allows the top row of keys on the Attendant Console to perform and
display multiple functions in accordance with the status of call processing.
Multiple Console
Operation
This feature allows more than one Attendant Console to operate within the same
system.
Page 42
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Attendant Delay Announcement
Pushbutton
Calling - Attendant
Only
This feature permits an operator to place all calls over Dual-Tone, Multi-Frequency
(DTMF) lines from the pushbutton keypad on the Attendant Console.
Serial Call
This feature is activated by the Attendant when an incoming calling party wishes to
speak with more than one internal party. When the internal station subsequently
disconnects from the Central Office line call, the Central Office party automatically
rings back to the same Attendant.
Time Display
This feature provides a digital time display on the Attendant Console (SN610) LCD.
Trunk Group Busy
Display
A visual indication is supplied to the Attendant when all trunks in a particular trunk
group are busy.
Unsupervised
Trunk-to-Trunk
Transfer By
Attendant
This feature allows an Attendant to transfer an incoming or outgoing call on one trunk
to an outgoing trunk and exit the connection before the called party answers.
Attendant Delay Announcement
This feature provides an announcement, via a Digital Announcement Trunk Card, to
external calls that are not answered by the attendant within a predetermined time.
Attendant Lockout
This feature denies an Attendant the ability to reenter an established trunk or station
connection without being recalled by that station after the call is put in consultation
hold.
Attendant Overflow
When an incoming call, which has terminated from a trunk to the Attendant Console,
remains unanswered after a predetermined time period, this feature provides a change
to Night Service for that particular trunk.
Attendant Override
This feature permits an Attendant to enter a busy connection (station or trunk) using
the Attendant Console. When this feature is activated, a warning tone is sent to the
connected parties after which, they are connected with the Attendant in a three-way
bridge.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 43
Authorization Code
Chapter 5 Feature Description
Authorization Code
An Authorization Code is a numerical code which will temporarily change a station’s
Class of Service to a Class of Service assigned to that Authorization Code. This new
Class of Service allows access to trunks, dialing patterns, and/or features that would
otherwise be restricted.
Automated Attendant
This feature allows the system to answer incoming trunk calls. The system will supply
a message and/or dial tone to the caller. The caller can then dial the desired extension
number and be directed to that station.
Automatic Call Distribution (ACD)
The Automatic Call Distribution (ACD) feature permits incoming calls to terminate to
a prearranged group of stations. Calls are distributed in the order of arrival to idle
terminals within the group, based on which terminal has been idle the longest period
of time. Stations may log on/log off from the ACD group. Supervisor stations may
monitor conversations of agents.
Busy In/Busy Out ACD
This feature allows an agent in an ACD group to log their station onto or off of the
group. This allows the system to control whether a call directed to the pilot number of
the ACD group goes to that station or not. This prevents incoming calls from being
directed to stations at which no agent is available.
Call Waiting
Indication - ACD
This feature provides a visual indication when an incoming call to an ACD group is
placed in queue, due to an “all agents busy” condition. On external relay controlled
indicator or an LED on a Multiline Terminal can be used to provide Call Waiting
Indication.
Delay
Announcement ACD
This feature allows the system to provide a recorded announcement to an incoming
caller placed in queue to an ACD group. A single announcement, or two separate
announcements, can be provided.
Hunt Past No
Answer - ACD
This feature allows calls targeted at an ACD group to hunt past an agent’s station,
after a no answer condition, if the agent forgets to log off of the group and the agent is
unable (or not available) to answer the call.
Immediate
Overflow - ACD
This feature allows a call directed to an ACD group to immediately overflow to
another ACD group, upon encountering an “all agents busy” condition.
Priority Queuing ACD
This feature allows the system to prioritize incoming calls by trunk route and on a per
station basis, when the call enters an ACD queue. When a call is considered as a
priority, it is placed at the beginning of the queue.
Page 44
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Automatic Call Distribution with Management Information System (MIS)
Queue Size
Control - ACD
On incoming DID/Tie line calls, the system can be assigned a threshold which limits
the number of calls in queue. When the queue size threshold is exceeded, incoming
callers are connected to busy tone.
Silent Monitor ACD
This feature provides the ACD group supervisor with the ability to monitor a call to an
ACD agent. The silent monitor function gives no indication (as an option) to either the
agent or the calling party.
Automatic Call Distribution with Management Information System
(MIS)
The Automatic Call Distribution (ACD) with Management Information System (MIS)
feature provides a management information system to be used in conjunction with the
built-in ACD features of the system. The MIS incorporates a supervisor's terminal for
real-time monitoring of agent activity, amber and red alarms, and hard-copy summary
reports.
Automatic Camp-on
An incoming Direct Inward Termination (DIT) call which has been terminated to a
busy station can be Camped-On automatically. When the busy station becomes idle,
the station is automatically called and connected to the camped on incoming trunk
call.
Automatic Number Identification (ANI)
This feature receives the calling subscriber's number automatically sent from T1
network using MF signaling and displays the calling number on the LCD of a
Multiline Terminal and an Attendant Console.
Automatic Recall
This feature works as a timed reminder. When a call remains on Hold, Camp-On or
ringing unanswered for a fixed interval after being transferred, the station that initiated
the hold, transfer, or Camp-On is automatically alerted. Station Application All
stations.
Automatic Wake-up
This feature allows the system to be programmed to automatically call guest rooms or
administration stations at specified times. Upon answering, the guest is connected to a
recorded announcement or music source. A printout of unanswered or blocked
Automatic Wake-Up attempts for each guest room is provided using the Hotel/Motel
printer.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 45
Background Music
Chapter 5 Feature Description
Background Music
Background Music can be provided on a dial-up basis over Multiline Terminal
speakers. Incoming voice announcements, ringing and recalls override Background
Music. Up to 10 music programs can be offered.
Boss / Secretary Calling
A secretary with a Multiline Terminal can use an appearance of the boss' extension to
screen calls for that extension, and announce and/or transfer calls to that extension.
Additionally, the secretary can call the boss during a busy condition and send a
Message Waiting Indication to the boss' station.
Broker's Call
This feature allows a Multiline Terminal or Single Line Telephone user to alternate
between two parties, talking to one party while the other party remains on Hold on the
same line. The Multiline Terminal user uses the TRF or ANS key to alternate between
the two parties. The Single Line Telephone user uses the Hold feature to alternate
between the two parties.
Call Back
This feature allows a calling party to set an automatic Call Back when a busy or no
answer condition is encountered. When the busy station becomes idle, the station that
set the Call Back will be called. In case of Call Back no answer, the Call Back to the
setting station is initiated immediately after the called station goes on hook after
making a call or accessing a feature.
Call Forwarding
Call Forwarding allows calls directed to a station to be routed to another station, an
Attendant, an outside number or voice mail equipment. The types of Call Forwarding
provided are:
•
•
•
•
•
•
•
•
•
•
•
•
•
Page 46
Call Forwarding - All Calls
Call Forwarding - Busy Line
Call Forwarding - No Answer
Call Forwarding - Destination
Multiple Call Forwarding - All Calls
Multiple Call Forwarding - Busy Line
Multiple Call Forwarding - No Answer
Split Call Forwarding - All Calls
Split Call Forwarding - Busy Line
Split Call Forwarding - No Answer
Attendant Call Forwarding Setup and Cancel
Call Forwarding - Override
Group Diversion
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Call Forwarding
Attendant Call
Forwarding Set-up
and Cancel
All of the various types of Call Forwarding can be set up or canceled from both
Attendant Consoles.
Call Forwarding All Calls
This feature allows all calls directed to a particular extension to be rerouted to an
alternate destination, regardless of the busy or idle status of the extension. Call
Forwarding - All Calls can be set by an Attendant Console, the individual station user,
a Multiline Terminal with a secondary appearance of the station's extension, or from
another station (which can program itself to be the destination of the rerouting).
Call Forwarding Busy Line
This feature permits a call to a busy extension to be routed to a pre-designated station,
Attendant Console, or voice mail equipment. Call Forwarding - Busy Line can be set
or canceled by an Attendant Console, the individual station user, or a Multiline
Terminal with a secondary appearance of the station's extension.
Call Forwarding No Answer
This feature reroutes calls to extensions which do not answer. These calls can be
rerouted to another station, an Attendant Console or voice mail equipment. Call
Forwarding - No Answer can be set by the individual station user, an Attendant
Console, or by a Multiline Terminal with a secondary appearance of the station's
extension.
Call Forwarding Destination
This feature allows a station (A) user to set Call Forwarding - All Calls from another
station (B) within the system, to the user's station (A).
Multiple Call
Forwarding - All
Calls
When a forwarded call is rerouted to a station that has also set a Call Forward, the call
can be forwarded to another station. A call can be forwarded up to a maximum of five
times, as specified in system programming.
Multiple Call
Forwarding - Busy
Line
This feature permits a call to a busy station to be forwarded, multiple times, to a
pre-designated idle station.
Multiple Call
Forwarding - No
Answer
This feature permits a call to an unanswered station, the ability to be forwarded
multiple times to a pre-designated station that does not have Call Forwarding - No
Answer set or to the Attendant Console.
Split Call
Forwarding - All
Calls
This feature allows all internal and external calls to a busy extension to be rerouted to
different destinations individually, regardless of the busy or idle status of the
extension.
Split Call
Forwarding - Busy
Line
This feature allows internal and external calls to a busy extension to be rerouted to
separate destinations. Destinations may be an internal station, Attendant Console, or
voice mail.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 47
Call Park
Chapter 5 Feature Description
Split Call
Forwarding - No
Answer
This feature allows internal and external calls, to extensions that do not answer, to be
rerouted to separate destinations individually.
Call Forwarding Override
This feature allows the call forward destination station to call the station which set call
forward. The call forward setting will be ignored.
Group Diversion
This feature allows all calls terminated to an extension that are not answered within a
predetermined time to be forwarded to a pre-designated station.
Call Park
This feature enables a station user or attendant to place a call into pre-designated Call
Park locations. The station user or attendant is then free to process other calls. This
feature is available system wide and for individual tenants.
Call Park - System
When a call is parked by Call Park-System, the call can be retrieved from Call Park by
any station in the system.
Call Park - Tenant
When a call is parked by Call Park - Tenant, the call can be retrieved from Call
Park-Tenant by any station within the tenant from which the call was originally
parked.
Call Pickup
This feature enables a station user to answer any call directed to another station, to a
station within the user's own Call Pickup Group, or to a station within a different Call
Pickup Group. Three Call Pickup methods are available: Call Pickup - Direct, Call
Pickup - Group, and Call Pickup - Designated Group.
Call Pickup - Direct
This method permits a station user to pickup a call to any other station in the system
by dialing a specific Call Pickup feature access code and the number of the called
extension.
Call Pickup Group
This method permits a station user to answer any calls directed to other extensions in
their preset pickup group by dialing a Call Pickup - Group feature access code.
Call Pickup Designated Group
This method permits a station user to answer an incoming call directed to another
group by dialing the Call Pick-up - Designated Group feature access code and any
station within the group to which the ringing station belongs.
Page 48
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Call Redirect
Call Redirect
Without answering incoming calls or held calls that terminate to the line keys of a
Multiline Terminal, the calls can be transferred to a pre-programmed station or Voice
Mail System. Two transferring destination number can be designated per tenant, in
system data programming. This feature can be used together with the Caller ID
Display feature.
Call Transfer
This feature permits a station user to transfer a call to another station in the system
directly, or with assistance from the attendant.
Call Transfer All Calls
This feature permits a station user to transfer incoming or outgoing calls to another
station within the system without attendant assistance.
Call Transfer Attendant
This feature permits a station user, while connected to an internal or outside call, to
signal the Attendant and have the Attendant transfer the call to another station within
the system or to an outside connection.
Caller ID Class
This feature receives the calling subscriber’s name and number sent from a public
network using a MODEM signal and displays the name or number on an LCD of a
Multiline Terminal and Attendant Console.
Caller ID Display
Without answering incoming calls or held calls which terminate to the line keys of a
Multiline Terminal, the calling party's information can be confirmed by the
indications on the LCD. The following information is indicated according to the kind
of the calls.
Camp-on
This feature provides selected stations or outside calls with Camp-On capability to a
busy internal station. Two Camp-On methods are provided. The call waiting method
allows a station or an outside party to camp itself on to a busy station. The transfer
method allows a transferred outside call to be camped-on to a busy station.
Centrex Compatibility
A combination of features allows full integration of the NEAX2000 IVS 2 with
Centrex service.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 49
Check In / Check Out
Chapter 5 Feature Description
Check In / Check Out
When this feature is activated, the following operations occur:
•
Check In
•
Room Cutoff is cleared.
•
Check Out
•
Room Status printout is supplied.
•
Do Not Disturb is reset.
•
Room Cutoff is set.
•
Message Waiting is reset.
•
Automatic Wake Up is cleared.
Class of Service
This feature permits all stations to be assigned a Class of Service in accordance with
the degree of system use desired. The Class of Service is used to assign restrictions for
trunk access and feature access.
Code Restriction
This feature allows the NEAX2000 IVS2 to be programmed to restrict outgoing calls
according to specific area and/or Central Office codes. This restriction is controlled on
the basis of a three-digit area code or six-digit area and office code numbering plan.
Conference (Three/Four Party)
This feature provides a station user the ability to add-on another party (trunk or
station) to a call already in progress. Single Line Telephone users can add up to one
additional party and Multiline Terminal users can add up to two additional parties.
Conference (Six/Ten Party)
This feature permits a station user or Attendant (conference leader) to establish a
Conference among as many as six or ten parties (including the Conference leader).
Consecutive Speed Dialing
For Speed Dialing, all digits are registered as a Speed Dialing Code. In the case of
Consecutive Speed Dialing, the common portion of the number is registered as a
speed calling code, and the remaining digits of each number are dialed by each
individual calling station or by using a Station Speed Dial key on a Multiline
Terminal.
Page 50
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Consultation Hold
Consultation Hold
This feature permits a station user to hold any incoming or outgoing CO call, tie line
call, or any intra-office call while originating a call to another station user within the
system.
Customer Administration Terminal (CAT)
In addition to the Maintenance Administration Terminal (MAT), programming of the
NEAX2000 IVS2 can be done from selected Multiline Terminals with LCD. The
designated Multiline Terminals can be placed in program mode, and system data can
then be changed. To prevent unauthorized changes, password levels are assigned,
providing authorization for access to certain areas of programming and denying
access to others.
Data Line Security
This feature allows line circuits that are used for data transmission to be protected
from interruptions such as Attendant Camp-On, Executive Override, and Attendant
Override.
Delayed Ringing
This feature enables trunks and station lines to ring immediately at the terminating
station, but also, after a programmable period of time has elapsed, to ring at secondary
Multiline Terminals with that trunk or line appearance.
Diagnostics
To assist maintenance personnel, the NEAX2000 IVS 2 provides diagnostic
capabilities such as fault code generation, device status information and alarm
information recording which can be accessed from the Maintenance Administration
Terminal (MAT) or Customer Administration Terminal (CAT).
Dial By Name
This feature allows a Multiline Terminal user to search for a desired number by name.
The number and name are registered in the system and they are shown on Multiline
Terminal LCD. The Multiline Terminal user can search for the desired number by
name using up or down soft keys. When the Multiline Terminal user finds the desired
number, the call can be originated by pressing the Line/Trunk key or going off hook.
Dial Conversion
The system can be assigned to use rotary Dial Pulse (DP) or Dual Tone
Multi-frequency (DTMF) trunks and stations. This feature provides for the repeating
of digits dialed by the station user onto the C.O. trunks.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 51
Direct Data Entry
Chapter 5 Feature Description
Direct Data Entry
This feature allows a maid or other hotel personnel to enter numeric data to the
Property Management System (PMS), using the guest room station for entry through
dial operation. The same numerical data can be output to a Hotel/Motel Printer by
system data programming.
Direct Digital Interface
This service feature provides the capability to connect trunks from the NEAX2000
IVS2 directly to T1 carrier links using either a private or public network.
Direct Inward Dialing (DID)
This feature provides for incoming calls from the exchange network (except FX or
WATS) to reach any station within the system without attendant assistance.
DID Call Waiting
This feature allows an incoming call on a DID trunk or a tie line to automatically be
Camped-On to the destination station if the destination station is busy.
DID Digit
Conversion
This feature allows the NEAX2000 IVS 2 to convert the digits received from the
serving C.O. to valid station numbers when the C.O. numbering plan differs from the
desired station numbering plan.
Direct Inward System Access (DISA)
This feature allows an outside caller to access the system using an exchange network
connection without Attendant or station assistance. The outside user may originate
calls over any or all of the system's facilities such as WATS, FX, Tie Line or CCSA.
The outside user can also directly call stations and access miscellaneous trunks for
such features as dictation access.
Direct Inward Termination (DIT)
This feature automatically routes incoming network exchange calls directly to a
pre-selected station without Attendant assistance. The call can then be processed by
the called party. Three-party Conference, Call Transfer, etc., are handled in the same
manner as any normal trunk call.
Direct Outward Dialing (DOD)
This feature permits any station user the ability to gain access to the exchange network
by dialing an access code and receiving new dial tone. The user may then proceed to
dial the desired exchange network number.
Page 52
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Direct Station Selection/Busy Lamp Field (DSS/BLF) Console
Direct Station Selection/Busy Lamp Field (DSS/BLF) Console
This feature allows an EDW-48-2A unit associated with a Multiline Terminal to be
used as a Direct Station Selection/Busy Lamp Field (DSS/BLF) Console. When the
buttons on the EDW-48-2A unit are programmed for Direct Station Selection (DSS)
buttons, up to 60 stations can be directly accessed in addition to those already
appearing on the Multiline Terminal. Busy status for each station is indicated by a red
LED associated with each button. In addition, the DSS console can provide the
following functions:
•
•
•
•
•
•
Message Waiting - Set/Cancel/Status Display
Do Not Disturb - Set/Cancel/Status Display
Automatic Wake Up No Answer - Status Display/Cancel
Agent Busy Out - UCD - Status Display
Line Lockout - Status Display
Room Cutoff - Set/Cancel/Status
Busy Out Status
Console
This feature allows an EDW-48-2A unit associated with a Multiline Terminal to be
used as a Busy Out Status Console. This feature is activated by use of a Function
Mode key on a DSS/BLF Console. Busy Out Status for each station is indicated by a
red LED associated with each button.
Do Not Disturb
Console
This feature allows an EDW-48-2A unit associated with a Multiline Terminal to be
used as a Do Not Disturb (DND) Console. This feature is activated by the use of a
Function Mode key on a DSS/BLF Console. DND set status for each station is
indicated by a green LED associated with each button. In addition, the Multiline
Terminal user can set/cancel the DND status of other stations using the DND Console.
Message Waiting
Console
This feature allows an EDW-48-2A unit associated with a Multiline Terminal to be
used as a Message Waiting (MW) Console. This feature is activated by the use of a
Function Mode key on a DSS/BLF Console. The Message Waiting status for each
station is indicated by a green LED associated with each button. In addition, the
Multiline Terminal user can set/reset MW status using the MW Console.
Room Cutoff
Console
This feature allows an EDW-48-2A unit associated with a Multiline Terminal to be
used as a Room Cutoff Console. This feature is activated by the use of a Function
Mode key on a DSS/BLF Console. The Room Cutoff status for each station is
indicated by a green LED associated with each button. In addition, the Multiline
Terminal user can set/cancel Room Cutoff to another station using the Room Cutoff
Console.
Wake Up No
Answer Console
This feature allows an EDW-48-2A unit associated with a Multiline Terminal to be
used as a Wake Up No Answer (WU) Console. This feature is activated by a function
mode key on a DSS/BLF Console. The No Answer status for each station is indicated
by a flashing green LED associated with each button.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 53
Distinctive Ringing
Chapter 5 Feature Description
Distinctive Ringing
This feature provides Distinctive Ringing patterns to the station so that the station user
can distinguish between internal and external incoming calls. This feature also enables
the LED associated with the line key of the Multiline Terminal to flash in two colors
according to the kind of incoming call.
Do Not Disturb
This feature restricts incoming calls to a station and can be set by an individual station
or from the Attendant Console. Placing a station in Do Not Disturb (DND) does not
prevent a station from originating a voice or data call or from receiving a data call.
This feature also allows a station to ensure privacy from telephone interruptions while
on an outgoing call. Additionally, the Attendant Console can place a group of stations
in the Do Not Disturb condition.
Do Not Disturb Hotel/Motel
This feature allows the Attendant Console(s), Hotel/Motel Front Desk Instrument(s),
guest stations or Property Management System (PMS) terminal(s) to place individual
stations into Do Not Disturb. Calls can be placed from stations set in DND.
Do Not
Disturb-System
This feature simultaneously restricts incoming calls to a pre-assigned group of stations
by operation from the Hotel/ Motel Front Desk Instrument(s). Attendant Console(s)
and Hotel/Motel Front Desk Instruments can use the DND OVR key to override this
Do Not Disturb setting.
Elapsed Call Timer
This feature provides a display of the elapsed time while a Multiline Terminal with
LCD is connected to any trunk.
Enhanced 911
This feature allows the PBX to transmit a caller’s emergency service identification
information to an Enhanced 911 Emergency system.
Executive Calling
This feature allows a station to be assigned a VIP class. This provides special ringing
to a called station when that station is idle, and automatic sending of three tone bursts
to a called station when that station is busy, provided the call was originated from a
station assigned as VIP class.
Page 54
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Executive Override
Executive Override
This feature allows selected users to override a busy condition on a called station. A
warning tone is transmitted to both stations in the busy call before the busy condition
is overridden, and a three-party Conference is then established.
External Paging with Meet-Me
This feature allows a station user or attendant dial-access to local voice paging
equipment and connects both parties automatically after the paged party has answered
the page by dialing an access code.
Fax Arrival Indicator
When a call from a C.O. line (Direct-Inward-Termination, Direct-Inward-Dialing,
Automated Attendant), station or tie line has terminated to a facsimile machine, a
related lamp on a pre-designated Multiline Terminal is caused to light, indicating
reception of a facsimile call.
Feature Activation from Secondary Extension
This feature allows the Multiline Terminal user to access an appearance of another
extension and program certain features from that extension.
Flexible Line Key Assignment
Multiline Terminals can have any desired line-key assignment. This feature permits
assignments to be tailored to each individual's needs. (The terminal's primary
extension line appearance is the only line key that cannot be reassigned.)
Flexible Numbering Plan
The NEAX2000 IVS2 has a Flexible Numbering Plan. All access codes and station
numbers and can be assigned in system programming. Refer also to the Single Digit
Dialing Features and Specifications, which further increases the flexibility of the
system.
Flexible Ringing Assignment
This feature allows lines on Multiline Terminals to be individually programmed to
ring or not ring.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 55
Forced Account Code
Chapter 5 Feature Description
Forced Account Code
This feature forces the user to enter an Account Code (up to 8 or 10 digits) for all
outgoing calls. The Account Code must be dialed before dialing the outgoing number.
Calls are processed only when the dialed Account Codes are valid.
Group Call
Automatic
Conference (6/10
Party)
This feature allows a Multiline Terminal user or single line telephone user within the
system to establish a conference among as many as six or ten parties. From a Multiline
Terminal /Single Line Telephone, a maximum of 9 stations can be paged
simultaneously plus the originator. The stations are assigned to the simultaneous
paging groups as participants by the system data beforehand.
2 Way Calling
This feature allows a Multiline Terminal/Single Line Telephone to page a maximum
of fifteen parties simultaneously including the originator. After one of paged parties
answers, the paging becomes the 2 Way Calling between the originator and the first
answered party, automatically stops paging other parties. The stations are assigned to
the simultaneous paging groups as participants by the system data beforehand.
Group Listening
When a Multiline Terminal user makes a call using the handset, pressing the SPKR
key will allow others to listen through the built-in speaker of the Multiline Terminal.
The user may continue talking on the handset at the same time.
Hands-free Answerback
This feature allows the station user to answer a voice call without lifting the handset.
Hands-free Dialing and Monitoring
This feature allows the station user to dial or monitor a call without lifting the handset.
Hold
This feature permits a user to Hold a call in progress. After Hold has been set, the
station user can make or answer new calls.
Call Hold
Page 56
This feature permits a user to Hold a call in progress by sending a hookflash and
dialing the Call Hold feature access code, or by pressing the Call Hold key. This line
can then be used for originating another call or returning to a previously held call.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Hotel/Motel Attendant Console
Dual Hold
This feature permits a station user who is placed on Hold by another station to place
that station on Hold also.
Exclusive Hold
This feature allows a Multiline Terminal user to place a call on Hold and to exclude all
other station users from retrieving the held call.
Non-exclusive
Hold
This feature allows a Multiline Terminal user to place a call on Hold that may be
retrieved by any station that has an appearance of the held line.
Hotel/Motel Attendant Console
The Attendant Console can be programmed to function as a Hotel/Motel Attendant
Console. In addition to the business features and functions of the Attendant, the
Hotel/Motel Attendant Console can set Room Cutoff (individual and group),
Automatic Wake Up, Message Waiting, and Do Not Disturb (individual and group).
Hotel/Motel Front Desk Instrument
A Multiline Terminal with LCD can be programmed to function as a Hotel/Motel
(H/M) Front Desk Instrument. This can be used to set and cancel standard H/M
features such as Message Waiting, Do Not Disturb, Automatic Wake Up, and Room
Cutoff.
Hotline - Inside/Outside
This feature causes the terminal to place a call to another station or to an outside party
automatically when the user selects the Hotline extension.
House Phone
This feature allows selected stations to reach the Attendant simply by going off-hook.
Individual Attendant Access
This feature permits a user to call a specific Attendant by dialing an Attendant call
code.
Intercept Announcement
This feature provides the automatic interception of Direct Inward Dialing (DID) and
Tie Line calls which cannot be completed due to unassigned station or level. The
caller hears a recorded Intercept Announcement that informs the caller that an
inoperative number was reached, and may supply the number for information.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 57
Intercom
Chapter 5 Feature Description
Intercom
Three types of Intercoms are available: Manual Intercom, Automatic Intercom, and
Dial Intercom. Each type of Intercom provides access to a small group of Multiline
Terminals with simplified calling methods.
Manual Intercom
The Manual Intercom groups have up to six Multiline Terminals sharing a common
signal path. Users can call other members of the Manual Intercom group by pressing a
Manual Intercom key; each press sends a tone burst over the speakers of all the
terminals in the group. When another user answers the call, a speech path is activated.
Automatic
Intercom
Automatic Intercom provides a path for Voice Announcement Calls with Handsfree
Answerback between two Multiline Terminals using a line key. Private conversations
can be held by using the Multiline Terminal handsets. The Busy/Idle status of the
associated Multiline Terminal is displayed on the Automatic Intercom line key LED.
Dial Intercom
Dial Intercom comprises up to 10 Multiline Terminals which can call each other using
a dedicated Dial Intercom line key with abbreviated dialing. Dial Intercom calls can
be Voice Announce with Handsfree Answerback or ringing calls.
Internal Tone/Voice Signaling
Multiline Terminals can signal incoming internal calls by Voice Announcement or by
ringing according to the programmed mode (Voice first or Ring first) of the called
terminal. The caller can dial the digit 1 to change from Voice Announcement to Ring
Tone or vice versa. The Multiline Terminal assigned this feature can program the
following two modes:
•
•
Voice Mode:
allows an incoming call to terminate with Voice Announcement.
Tone Mode:
allows an incoming call to terminate with ringing.
Internal Zone Paging with Meet-Me
This feature allows the Attendant Console and system users to page over the built-in
speakers of the Multiline Terminals within the assigned zone or all zones.
Last Number Redial
This feature allows users to redial the last station-to-station or outside number they
dialed using a feature access key or a feature access code. This is useful when the
called station is busy or does not answer.
Page 58
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Least Cost Routing - 3/6 Digit
Least Cost Routing - 3/6 Digit
This service feature allows the NEAX2000 IVS 2 to be programmed to route outgoing
calls over the most economical facility (WATS, FX, DDD). Based on the individual
area code and office code dialed (6-digit analysis), the system examines the
programmed tables and uses the trunk in the order specified.
Line Lockout
This feature automatically releases a station from the common equipment if the station
remains off-hook for longer than a programmed interval before dialing. Howler tone
may be programmed to be sent to the station in Line Lockout.
Line Pre-selection
This feature provides the station user with two ways to select an idle, held, recalling,
or ringing line before going off-hook.
Maid Status
This feature allows the Hotel/Motel (H/M) Front Desk Instrument, Property
Management System (PMS) terminal, or guest room station (using special access
code) to register the condition of each guest room.
Maintenance Administration Terminal (MAT)
The Maintenance Administration Terminal (MAT) is a Personal Computer (PC) used
for programming and maintenance of the NEAX2000 IVS2. The MAT can provide a
Maintenance Printout, Peg Count information and fault message output. Additionally,
the MAT can be used to Remove and Restore to Service any station in the system and
can read or save system data from disks. The MAT can assign the Key Data for the
Attendant Console.
Message Center Interface (MCI)
This feature provides an interface with a customer supplied Voice Mail System
(VMS) which can send Message Waiting lamp control data to the NEAX2000 IVS2.
Message Registration
This feature provides output from the system to a call accounting system using an
RS-232C connector. This allows the Hotel/Motel clerk to retrieve the information
needed to charge for local and toll calls.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 59
Message Reminder
Chapter 5 Feature Description
Message Reminder
This feature allows a user or Attendant to turn on the message waiting (MW) lamp of
a Single Line Telephone, or the Message Reminder (MSG) LED of a Multiline
Terminal (if assigned).
Message Waiting
This feature allows the Attendant Console, Hotel/Motel (H/M) Front Desk Instrument,
administrative station, or Property Management System (PMS) terminal to light a
lamp (on an uninterrupted or interrupted basis) on a Single Line Telephone or
Multiline Terminal to indicate a message is waiting.
In addition to the lamp indication control, this feature also provides the Voice
Message Waiting service that an originating station user can set to Message Waiting
with a prerecorded message by using the Digital Announcement Trunk card
(PN-2DATA).
Miscellaneous Trunk Access
This feature allows the connection of various types of external facilities. In addition to
Loop and Ground Start Trunks, the following can also be interfaced with the
NEAX2000 IVS 2: CCSA Lines Code Calling Equipment, Dictation Equipment,
Foreign Exchange (FX) Lines, Radio Paging Equipment, and Wide Area Telephone
Service (WATS) lines. Refer to separate features, Direct Inward Dialing (DID), and
Tie Line Access for more applications of Miscellaneous Trunk Access.
CCSA Access
This feature allows connection to or from a Common Control Switching Arrangement
(CCSA) network. A CCSA network is a special, privately-leased network constructed
for one customer's exclusive use that replaces or augments the public switched
network services.
Code Calling
Equipment Access
Code Calling Equipment consists of external paging units and external dialers
requiring dial access from the NEAX2000 IVS2.
Dictation
Equipment Access
This feature permits dial access to customer provided Dictation Equipment, and in
some instances allows them to maintain telephone dial control of normal dictation
system features.
Foreign Exchange
(FX) Access
An FX line is a line that is extended and terminated at a distant Central Office. With
this feature, outgoing calls over the FX line become a local call at the distant C.O.
Radio Paging
Equipment Access
This feature provides station users dial access to Radio Paging Equipment, and to
selectively tone - or voice/ tone-alert individuals carrying pocket paging devices. The
paged party (when on premises) can be connected to the paging party by going to the
nearest station and dialing an answer back code.
Page 60
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Wide Area
Telephone Service
(WATS) Access
Multiline Terminal Attendant Position
This feature allows any station user direct dial access to outgoing WATS lines.
Multiline Terminal Attendant Position
A Multiline Terminal with LCD can be programmed to function similar to an
Attendant position. This Attendant position has limited access to Attendant related
features and functions and can be substituted where an Attendant is required but an
Attendant Console is not necessary. When an EDW-48-2A unit is associated with this
Attendant Multiline Terminal enhanced operation is available.
Music on Hold
This feature plays music when a line is placed on hold. Music is provided by a circuit
board memory chip or a local music source, such as a CD player or a radio.
Nailed-down Connection - Data
This feature provides a fixed connection between two internal Data Adapters or an
internal Data Adapter and an external Data Communication Device.
Night Service
This feature provides a variety of methods for handling incoming calls when the
system is in night mode. These include:
•
•
•
•
•
•
•
Attendant Night Transfer
Call Rerouting
Day/Night Mode Change by Attendant Console
Day/Night Mode Change by Station Dialing
Night Connection-Fixed
Night Connection-Flexible
Trunk Answer Any Station
Attendant Night
Transfer
When the Attendant Console is in Night Service, any operator directed calls (dial 0
calls) are automatically routed to a preprogrammed station. Priority Calls and
Off-Hook Alarms which terminate to an Attendant are also routed by this feature.
Call Rerouting
This feature provides flexible reroute capabilities for a variety of calls when the
system is in night mode.
Day / Night Mode
Change by
Attendant Console
This feature provides activation of DAY/NIGHT Mode Change by depressing a
predetermined key from the Attendant Console.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 61
Off-hook Alarm
Chapter 5 Feature Description
Day / Night Mode
Change by Station
Dialing
This feature allows selected stations to activate a change from day mode to night
mode by dialing a special code.
Night Connection Fixed
This feature allows incoming calls normally terminated to the Attendant to reroute to a
predetermined station when the system is placed in Night Service.
Night Connection Flexible
This feature provides incoming calls normally terminated to the fixed night station to
be Call Forwarded to another station.
Trunk Answer Any
Station (TAS)
This feature allows any station, other than one with incoming restrictions, to answer
incoming calls when the system is in the night mode. When this feature is activated,
incoming exchange network calls will activate a common alert signal at the customer
premises. By dialing a specified code, any station may answer the call and then extend
it to any other station by means of the Call Transfer feature.
Off-hook Alarm
This feature allows a station user to call the Attendant, or a pre-designated station, by
simply staying off-hook for a preprogrammed period of time. The calling number is
automatically displayed at the Attendant Console, or the pre-designated station if
equipped with an LCD.
Off-Premises Extensions
This feature allows the connection of a single line telephone in an off-premises
location. The connection to the Off-Premises Extension can be through direct copper
or through the local telephone company.
Open Application Interface (OAI)
Provides a computer-to-PBX interface, allowing a computer to control the function of
the NEAX2000 IVS2. The NEAX2000 IVS2 can be customized to accommodate most
customer applications. Application software can be provided by NECAM, an outside
software house, or a customer.
Pad Lock
This feature temporarily restricts telephones from making unauthorized calls by
dialing special access code when station users are away from their seats.
Page 62
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Periodic Time Indication Tone
Periodic Time Indication Tone
This feature provides a periodic tone to the station user who has made an outgoing
call. This feature can be allowed or denied for each station.
Pooled Line Access
A line key can be assigned to access Pooled Lines. Each line key will allow incoming,
outgoing, or both-way access to a trunk route.
Power Failure Transfer
This feature provides for specified trunks to be automatically connected to designated
Single Line Telephones in the event of AC power loss. It is normally used when the
system is not equipped with reserve power.
Priority Call
This feature allows the Attendant to answer a call before other calls, at the Attendant's
discretion.
Privacy
This feature restricts Multiline Terminal users from depressing a busy line button and
entering a conversation unless permitted by the Multiline Terminal user currently on
that line button or if the line button is assigned for Direct Privacy Release.
Direct Privacy
Release
This feature allows a station user with a secondary appearance of another extension in
the system to access that extension when it is being used by someone else. This feature
allows for a simplified method for establishing a conference. In addition, this feature
can be used to emulate PC dialing, where a single line extension connected to a PC
can appear on a Multiline Terminal and be accessed by the Multiline Terminal user
after the PC is completed dialing.
Manual Privacy
Release
This feature allows a Multiline Terminal user to enter a conversation on a busy line
button if the Multiline Terminal user already in the conversation allows them by
releasing Privacy.
Private Lines
Only a C.O. trunk assigned to that specific station is seized when a station user
originates an outgoing C.O. call or when an incoming C.O. call is terminated at the
station designated by Direct-In-Termination. In this manner, stations and C.O. trunks
are to be associated on a 1-to-1 basis.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 63
Property Management System Interface
Chapter 5 Feature Description
Property Management System Interface
The NEAX2000 IVS 2 provides a data interface to a locally provided Property
Management System (PMS). This enables communication between the NEAX2000
IVS2 and the PMS in order to provide computer control of Hotel/ Motel features.
Proprietary Multiline Terminal
There are two Multiline Terminals available which can be used with the NEAX2000
IVS2.
•
•
•
ETJ-8-1: 8 line keys.
ETJ-16DC-1: 16 line keys with a Liquid Crystal
Display (LCD).
Automatic Idle
Return
This feature returns a station to the idle state after 3 seconds of reorder tone is received
due to the distant end disconnecting.
Called Station
Status Display
This feature provides a display on the status of a called station on the LCD of the
calling Multiline Terminal.
Calling Name and
Number Display
This feature provides a display on the LCD of the Multiline Terminal receiving a call,
indicating the station number or trunk number of the incoming call.
Dynamic Dial Pad
This feature allows to make an outgoing call at first hand by pressing a ten key of
Multiline Terminal, without pressing a Speaker key or going off-hook.
Handsfree Unit
The built-in Handsfree Unit enables full Handsfree operation for both internal and
external calls (No optional Handsfree Unit is required).
I-Hold / I-Use
Indication
Multiline Terminals provide indication of which line keys have been placed on Hold,
or are in use by that Multiline Terminal. The LED associated with the line key will
give the appropriate indication.
Microphone
Control
All Multiline Terminals are equipped with a Microphone Control button with an
associated LED.
Multiple Line
Operation
This feature allows for the appearance of multiple lines on the Flexible Line Keys and
feature keys of all Multiline Terminals.
Page 64
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Proprietary Multiline Terminal
Mute Key
This feature allows the distant extension user, of a station user that presses a mute key
during conversation, not to hear the station user's voice though the station user can
hear the distant extension user's voice. By pressing the mute key again, the mute status
returns to original conversation.
Off-Hook Voice
Announcement
This feature provides a secondary voice path to the Multiline Terminal with an APR-J
or APA-J unit. This allows the station to receive a voice call through the speaker while
on a handset call on the Primary Extension, a secondary extension, or a Direct Trunk
Line Appearance.
Prime Line Pickup
This feature allows a Multiline Terminal user to go off hook and originate a call from
the line assigned as the Prime Line without depressing the associated line key.
Recall Key
Each Multiline Terminal is equipped with a Recall Key that is used to generate a
hookflash to access features provided by the outside exchange, or to abandon a call
while retaining the line for origination of another call.
Relay Control
Function Key
This feature provides a Multiline Terminal with the ability to activate/deactivate
relays (on a PN-DK00) to control external devices.
Ring Frequency
Control
The ring frequency of the Multiline Terminal can be controlled on a station basis in
system programming (four frequencies are available) or by use of a function key on
the Multiline Terminal.
Ringing Line
Pickup
This feature provides the ability to answer any call ringing into a Multiline Terminal
by just lifting the handset.
Soft Keys
According to the status of the Multiline Terminal, function keys (Soft Keys) are
displayed in the third line on the LCD. If the status of Multiline Terminal changes, the
Soft Keys will change automatically. Also if the Help key is pressed, explanation of
indicated Soft Keys are shown on the LCD.
Volume Control
Multiline Terminals are equipped with common Volume Control keys for:
•
•
•
•
•
Built-in Speaker / Handset Receiver Volume.
Ring Volume.
C.O. Transmission Level.
LCD contrast.
Ring Tone Frequency
The Volume Control keys are located on the lower front side of Multiline Terminals
(UP and DOWN).
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 65
Q-SIG Circuit Switched Basic Call - ETSI Version
Chapter 5 Feature Description
Q-SIG Circuit Switched Basic Call - ETSI Version
This feature provides a tie-line connection between NEAX2000 IVS2 and the other
Q-SIG PBX using the ISDN protocol in conformity with ETS 300 172 standardized
by ETSI (European Telecommunications Standards Institute).
Remote Hold
This feature allows a Multiline Terminal user to hold it on the line button of
transferred terminal, by pressing the Hold key.
Remote PIM
When the system has two or more PIMs, the PIMs can be installed separately by T1
digital interface. A maximum of 3 PIMs can be installed apart at the remote site.
Reserve Power
This feature provides backup power from a 24V battery source in the event of a
commercial power failure.
Resident System Program
This feature provides the installers a simple procedure to have the system generate
system data according to the system hardware configuration, thereby providing
immediate operation and shorter programming time. When activated, the system scans
hardware configuration (such as line/trunk card slot location) and assigns system data
(such as extension numbers, trunk numbers, etc.) according to a predetermined
generic program assignment.
Return Message Schedule Display
This feature permits any station user to register his Return Schedule from his phone
when he leaves his desk or the premises, and have the Return Schedule displayed on a
calling Multiline Terminal with a Liquid Crystal Display (LCD) during his absence.
Room Cutoff
This feature allows the Attendant Console, Hotel/Motel (H/M) Front Desk Instrument,
or Property Management System (PMS) terminal, or guest room telephones using a
special access code, to temporarily restrict guest room telephones from making
unauthorized calls when guests are away from their room, and when rooms are in
Check Out status.
Page 66
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Room Status
Room Status
This feature provides the Hotel/Motel (H/M) Front Desk Instrument with a visual
display of the guest's room status. A supplementary print out (individual and
summary) can be provided.
Route Advance
This feature automatically routes outgoing calls over alternate facilities when the first
choice trunk group is busy. Users select the first choice route by dialing the
corresponding access code, and the equipment then advances through alternate trunk
groups only if the first choice is busy.
Save and Repeat
This feature allows a Multiline Terminal to save a specific dialed number and then
redial that number at a later time.
Security Alarm
This feature provides an indication on the Attendant Console when a contact closure
occurs.
Set Relocation
This feature enables two stations to be moved from one location to another without
reprogramming station data at MAT.
Single Digit Dialing
This feature provides the station user the ability to dial single digit codes to access
certain features while still allowing the same digit dialed to be used as the first digit of
guest room station numbers.
Software Line Appearance (Virtual Extensions)
This feature permits assignment of circuits which do not physically exist, to be used as
secondary extensions on Multiline Terminals. There are 256 software lines that can be
assigned to line keys and used as desired.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 67
Stack Dial
Chapter 5 Feature Description
Stack Dial
This feature enables a Multiline Terminal or an Attendant Console to remember the
numbers dialed in the preceding five calls, including the last number dialed. The stack
dial numbers are sequentially displayed on the LCD display, thus allowing the station
user to make an outgoing call by selecting the desired dialed number from the display.
Station Hunting
Three Station Hunting arrangements are available. Station Hunting - Circular
processes the call no matter which station in the hunt group is called. Station Hunting
- Terminal initiates a hunt only when the pilot number of a hunt group is called.
Station Hunting - Secretarial is initiated when a busy secretarial station in a Station
Hunting - Circular group or Station Hunting - Terminal group is reached.
Station Hunting Circular
When a busy station in a hunt group is called, this feature permits the call to be
processed automatically through the hunt group in a preprogrammed order from that
station's position within the hunt group.
Station Hunting Terminal
When a pilot number is dialed and that number is busy, sequential Station Hunting
will be initiated. However, if a number other than the pilot number is dialed and that
number is busy, busy tone will be provided rather than initiate Station Hunting.
Station Hunting Secretarial
This feature allows assignments to be given to members of Terminal and Circular
Hunting groups to reroute calls (when their hunting group is all busy) to a back-up
hunting group.
Station Message Detail Recording (SMDR)
This feature provides a call record for outgoing station-to-trunk calls and incoming
trunk-to-station calls (including Data Call). This facilitates cost control by identifying
trunk use and misuse by individual stations. Station Message Detail Recording
(SMDR) enables call billing to customers and clients, and provides a means for
checking local telephone bills.
Station Speed Dialing
This feature allows a station user to dial frequently called numbers by dialing an
access code and an abbreviated code, or by depressing a feature key or line key
assigned for Station Speed Dialing capability.
Page 68
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Step Call
Step Call
This feature allows the Attendant or station user, after calling a busy station, to call an
idle station by simply dialing an additional digit. This feature will operate only if the
number of the idle station is identical to that of the busy station in all respects, except
the last digit.
Supervisory Control of Peripheral Equipment
When various types of peripheral equipment (such as facsimiles, dictation equipment,
Voice Mail, etc.) are connected to the line circuits of the NEAX2000 IVS 2, this
feature allows the loop of the line circuit concerned to open for a programmable
interval, and send a release signal to the peripheral equipment when the calling party
disconnects.
System Speed Dialing
This feature provides all users the ability to dial frequently called numbers using an
abbreviated call code.
System Traffic
The NEAX2000 IVS 2 is the stored program controlled digital electronic PABX
employing PCM time division switching technique. Single stage time division
switching is employed for all configurations of NEAX2000 IVS2 up to its maximum
line and trunk configuration. Traffic capacity is expressed in Busy Hour Call Attempts
(BHCA). This value is the number of call attempts that can be generated in the busiest
hour of the day.
Tenant Service
This feature provides for more than one organization (tenant) to share the same
NEAX2000 IVS2 system. Through system programming, each organization may be
restricted to its own Central Office trunks, Attendant Consoles and extension group.
In addition, incoming calls are directed to the specific tenant.
Tie Lines
This feature allows any station user dial access or direct access to an E&M Tie Line.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 69
Tie Line Tandem Switching
Chapter 5 Feature Description
Tie Line Tandem Switching
This feature allows trunk-to-trunk connections through the NEAX2000 IVS2 without
the need for any Attendant assistance or control. The major use of this feature is in
association with a dial tandem tie line network to allow tie line connections and
incoming tie line calls automatic access to, and completion of, local Central Office
calls.
Timed Queue
When a user originates an outgoing trunk call and the called party is busy or does not
answer, the caller can set the Timed Queue feature. When this feature is set, the trunk
seizure is repeated and the number is redialed after a predetermined time interval.
Timed Reminder
This feature allows the system to be programmed to automatically call stations at
specified times. Upon answering, the station is connected to a recorded announcement
or music source.
Trunk - Direct Appearances
This feature allows Multiline Terminal users the ability to access a CO line or E&M
Tie Line without dialing an access code. For this feature, trunks must be assigned to
the line keys on the Multiline Terminal. Incoming calls on CO lines can be answered
on the appropriate trunk line appearance.
Trunk Queuing - Outgoing
This allows a station user, upon encountering a busy signal on a trunk, to dial a feature
access code and enter a first-in, first-out queue. As soon as an outgoing trunk becomes
available, stations in the queue will be called back on a first-in, first-out basis.
Trunk-to-Trunk Connection
This feature provides any station user with the ability to conference together two
outside trunk calls and abandon the connection without dropping the Trunk-to-Trunk
Connection.
Page 70
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Uniform Call Distribution (UCD)
Uniform Call Distribution (UCD)
The Uniform Call Distribution (UCD) feature permits incoming calls to terminate to a
prearranged group of stations. Calls are distributed in the order of arrival to idle
terminals within the group, based on which terminal has been idle the longest period
of time. Stations may log on/log off from the UCD group. Supervisor stations may
monitor conversations of agents.
Busy In/Busy
Out-UCD
This feature allows an agent in a UCD group to log their station onto or off of the
group. This allows the system to control whether a call directed to the pilot number of
the UCD group goes to that station or not. This prevents incoming calls from being
directed to stations at which no agent is available.
Call Waiting
Indication-UCD
This feature provides a visual indication when an incoming call to a UCD group is
placed in queue, due to an “all agents busy” condition. An external relay controlled
indicator or an LED on a Multiline Terminal can be used to provide Call Waiting
Indication.
Delay
AnnouncementUCD
This feature allows the system to provide a recorded announcement to an incoming
caller placed in queue to a UCD group. A single announcement, or two separate
announcements, can be provided.
Hunt Past No
Answer-UCD
This feature allows calls targeted at a UCD group to hunt past an agents station, after a
no answer condition, if the agent forgets to log off of the group and the agent is unable
(or not available) to answer the call.
Immediate
Overflow-UCD
This feature allows a call directed to a UCD group to immediately overflow to another
UCD group, upon encountering an “all agents busy” condition.
Priority
Queuing-UCD
This feature allows the system to prioritize incoming calls by trunk route and on a per
station basis, when the call enters a UCD queue. When a call is a considered as
priority it is placed at the beginning of the queue.
Queue Size
Control-UCD
On incoming DID/Tie line calls, the system can be assigned a threshold that limits the
number of calls in queue. When the queue size threshold is exceeded, incoming callers
are connected to busy tone.
Silent
Monitor-UCD
This feature provides the UCD group supervisor with the ability to monitor a call to a
UCD agent. The silent monitor function gives no indication (as an option) to either the
agent or the calling party.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 71
Uniform Numbering Plan (UNP) -Voice and Data
Chapter 5 Feature Description
Uniform Numbering Plan (UNP) -Voice and Data
In the numbering plan for a network to be configured through the use of Tie Lines, a
Uniform Numbering Plan (UNP) is employed. When UNP is employed, a station user
from any PBX within the network can call a desired party by using a uniform dialing
method based on the UNP.
Variable Timing Parameters
This feature gives the IVS the versatility to change timing duration using the
Maintenance Administration Terminal (MAT) or the Customer Administration
Terminal (CAT). All timing parameters are set initially in the Resident System
Program. These timing parameters can be changed according to the customer's
requirements.
Voice Guide
This feature provides a station user with an announcement that informs:
1. The result of the operation when the station user set or canceled the service feature, instead of service set tone.
2. Which service has been set to the station; such as, Call Forwarding - All Calls, Do
Not Disturb or Message Waiting, when the station goes off-hook, instead of
special dial tone.
Voice Mail Integration
This feature is used to interface the NEAX2000 IVS 2 with a locally provided
stand-alone type Voice Mail System (VMS). The VMS, connected to the NEAX2000
IVS2 single line circuit (LC), is controlled by sending/receiving DTMF signals using
this LC.
The VMS’s voice mail feature can be used by accessing this VMS directly from an
extension. If a station sets its call forwarding destination to the VMS, calls to this
station are connected to the VMS, and the messages can be registered according to the
VMS instruction. In addition, the Message Waiting lamp of the station can be turned
on automatically by the VMS.
Voice Mail Private Password
Voice Mail Password can be prevented from displaying in LCD of Multiline
Terminals when connected to the Voice Mail System.
Page 72
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 5 Feature Description
Voice Mail Transfer
Voice Mail Transfer
This feature has two functions that provide streamlined transfer access to voice mail.
1. One touch access to VMS: When an Attendant transfers an external call to a station, and if the station is busy or unanswered, the Attendant can transfer the call to
a VMS by dialing “9” or by pressing a function key provided for this feature.
2. Transferring Camp-On call to VMS: When an Attendant sets Camp-On to a busy
destination station for an external call, and if the destination station does not
answer by predetermined time, the call can be automatically transferred to a VMS.
Whisper Page
This feature allows a secretary to interrupt the boss in a private way. By pressing a
feature key or dialing an Access Code, the secretary station can voice override the
conversation between the boss and another party (station or trunk). When the
conversation is interrupted, the boss can hear the secretary but the other party is
unaware of the Voice Override.
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 73
Page 74
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 6
Installation Procedure
Installation Steps
The installation of the NEAX2000 IVS2 is performed according to the following
steps.
Unpacking
Installation of PIM
Cabling
Mounting Cards
System Data Entry
Operation Test
In Service
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 75
Items to be Provided at Site
Chapter 6 Installation Procedure
Cabling inside the unit, between the switching equipment and the MDF, can all be
done by plug-and-jack connections, while printed circuit cards can easily be plugged
into the edge connectors.
On all installations, a special provision for plug-and-jack connections completely
eliminates possible errors in wiring. This allows the installation to be done easily and
smoothly.
Items to be Provided at Site
The following items are required for correct operation.
a.) Adequate space accommodation
b.) Adequate ventilation
c.) Commercial AC power
Dimensions and Weight
1. Dimensions: 16.9 in. x 8.8 in. x 14 in. (43 cm x 22.3 cm x 35.6 cm)
2. Weight (: Weight varies depending on the system configuration)
PIM: Approx. 41 lbs. (18.5 kg)/PIM (including PWR and 19 Cards)
Heat Dissipation
Table 6-1
Page 76
Specifications for Heat Dissipation
PIM NO.
MAX. AC POWER
CONSUMPTION (W/H)*
MAX BTU (BTU/H)
1
360
1226
2
720
2452
3
1080
3678
4
1440
4904
5
1800
6130
6
2160
7356
7
2520
8582
8
2880
9805
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 7
Maintenance
Trouble Reporting and Diagnosis
The urgency of a fault is indicated by the MJ/MN lamp provided on the Power Card
and optional external alarm indicator. Details of the alarm indications are shown in
Table 7-1.
Faulty plug-in cards are quickly replaced with a spare providing minimum disruption
of service and no loss of system memory.
Table 7-1
ITEM
DESCRIPTION
Fault Detection Items
ALARM INDICATION POWER
CARD/EXTERNAL
ALARM INDICATOR
(OPTION)
MJ
MN
1
Reset Initial
Available
Available
2
Data Transmission Error
between MP and FP/AP
Available
Available
3
FP/AP Card Down
Available
Available
4
Digital Interface Fault
Available
Available
5
BUS Card Fault
Available
Available
6
Dterm
Available
Available
Line Fault
7
Station Line Fault
Available
Available
8
D-channel Circuit Down
Available
Available
9
Common Channel Down
Available
Available
10
Number of lockout station
exceeds a predetermined
value
Not Available
Available
11
SMDR Memory overflow
Available
Available
12
AC Power Down
Available
Available
13
DC Output Down
Available
Available
14
Fuse Blown
Available
Available
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
REMARKS
Indication of MJ or
MN alarms is
software-controlled
on a per fault basis.
Page 77
System Administration
Chapter 7 Maintenance
System Administration
System data, which varies from installation to installation and which is subject to
continual change during service, is readily entered or changed from the Dterm or MAT
(Maintenance Administration Terminal).
The system data can be downloaded to, or uploaded from, a floppy disk in the MAT
computer.
Remote Maintenance
Access to the NEAX2000 IVS2, for the purpose of system diagnosis, status reporting,
and database reconfiguration, can be performed from remote locations (e.g.,
Maintenance Centers, Technical Assistance Service Centers, etc.). By taking
advantage of the built-in modem on the NEAX2000 IVS 2 CPU, the following
maintenance administration functions can be accomplished by a remotely located
MAT via a modem over a central office network or a tie line network.
Page 78
•
System Data Correction/Upload/Download
•
MP/FP Software Upgrade
•
Control of Battery Disconnection
•
Display of Line/Trunk Connections
•
Detection of open or short circuit in the line cables for both analog and D term telephones
•
Fault Message Display
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 8
System Performance
Operating Conditions
Ambient Temperature: 32°F ~ 104°F (0°C ~ 40°C)
Relative Humidity:
90% max (non-condensing)
Transmission Characteristics
a.) Cross Talk Attenuation: More than 70 dB at 1000 Hz
b.) Idle Circuit Noise: Less than -65 dBm
c.) Insertion Loss (relative to 1KHz-10 dBm):
•
•
•
Station-to-Station
Station-to-Trunk
Trunk-to-Trunk
- Typical 6 dB
- Typical 0.5 dB
- Typical 0.5 dB at 0 dB PAD control
d.) Longitudinal Balance
Trunk Side: Better than 58 dB
e.) PCM Characteristics:
•
Line Rate - 1.544 Mbps
•
µ-Law
•
Meets North America TI-04 Standards
f.) Return Loss: More than 15 dB (300 ~ 3,400 Hz)
•
Line Impedance:
Trunk:
Station: 600 Ω
600 or 900 Ω
g.) Leakage Resistance: More than 20,000 Ω
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Page 79
Rotary Dial Pulse and DTMF Signaling
Chapter 8 System Performance
Rotary Dial Pulse and DTMF Signaling
1. Receiving Conditions:
Dial Speed:
9 ~ 11 pps
Break Ratio:
55 ~ 77% (10 pps)
Minimum Interdigital
Pause:
192 ms
Switch Hook Flash:
Detection:
310 ~ 1610 ms
2. Sending Conditions
Dial Speed:
Break Ratio:
Minimum Interdigital
Pause:
10 pps (±0.8 pps)
67 ± 3%
800 ms
3. DTMF Signaling
Frequency Combinations
HIGH/LOW
1209 HZ
1336 HZ
1477 HZ
697 Hz
1
2
3
770 Hz
4
5
6
852 Hz
7
8
9
941 Hz
*
0
#
1. Receiving Conditions
(Measured at Receiver Input)
Signal Duration:
Interdigital Pause:
Signal Level:
More than 40 ms
More than 40 ms
0 ~ -25 dBm
2. Sending Conditions
Signal Duration:
Inter-digital Pause:
Signal Level:
Page 80
More than 64 ms
More than 64 ms
Low Frequency: -10 dBm
High Frequency: -9 dBm
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Chapter 8 System Performance
Audible Tones and Ringing Signal
Audible Tones and Ringing Signal
Audible Tones
Table 8-1
Specifications of Audible Tone
TONE
FREQUENCY
INTERRUPTION
Dial Tone (DT)
350 Hz mixed with 440 Hz
Continuous
Special Dial Tone (SDT)
350 Hz mixed with 440 Hz
0.125 sec. ON, 0.125 sec. OFF
Busy Tone (BT)
480 Hz mixed with 620 Hz
0.5 sec. ON, 0.5 sec. OFF
Reorder Tone (ROT)
480 Hz mixed with 620 Hz
2.5 sec. ON, 0.25 sec. OFF
Howler Tone (HWT)
2,400 Hz interrupted by 16 Hz
Continuous
Service Set Tone (SST)
350 Hz mixed with 440 Hz
Continuous
Ring Back Tone (RBT)
440 Hz mixed with 480 Hz
1 sec. ON, 3 sec. OFF
Hold Tone (HDT)
480 Hz mixed with 620 Hz
0.25 sec. ON, 0.25 sec. OFF 0.25
sec. ON, 1.25 sec. OFF
Second Dial Tone
440 Hz mixed with 480 Hz
0.25 sec. ON, 0.25 sec. OFF 0.25
sec. ON, 1.25 sec. OFF
Call Waiting Ring Back Tone
440 Hz mixed with 480 Hz
1 sec. ON, 1 sec. OFF
Ringing Signal
Frequency:
20 Hz (Nominal)
Signal Voltage:
75 Vrms (Nominal)
Interruption:
•
2 sec. ON,
4 sec. OFF (for external call)
•
1 sec. ON and
2 sec. OFF (for internal call)
Built-In Modem on MP Card
MODEM:
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
33.6 kbps
Page 81
BHCA (Busy Hour Call Attempts)
Chapter 8 System Performance
BHCA (Busy Hour Call Attempts)
The BHCA of the NEAX2000 IVS2 is shown below.
MAIN PROCESSOR
WITHOUT FP
(1 PIM)
ONE FP
(1~2 PIM)
TWO FP
(3~4 PIM)
THREE FP
(5~6 PIM)
FOUR FP
(7~8 PIM)
Business or
Hotel/Motel without
ACD/OAI
2000
2500
5000
7000
8000
Business or
Hotel/Motel with
ACD/OAI
1000
2000
4000
5000
5500
Page 82
NEAX2000 IVS2 General Description
NDA-24293, Issue 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement