TVS Diode Arrays Lightning Surge Protection - SP3051 Series (SPA Diodes)

TVS Diode Arrays Lightning Surge Protection - SP3051 Series (SPA Diodes)
TVS Diode Arrays (SPA® Diodes)
Lightning Surge Protection - SP3051 Series
SP3051 Series 6V 20A Diode Array
RoHS
Pb GREEN
The SP3051 integrates low capacitance rail-to-rail diodes
with an additional zener diode to protect each I/O pin
against ESD and high surge events. This robust device can
safely absorb 20A of current per IEC61000-4-5 (tP=8/20µs)
without performance degradation and a minimum ±30kV
ESD per IEC61000-4-2. Their very low loading capacitance
also makes them ideal for protecting high speed signal pins.
Features
I/O 4
GND
VCC
I/O 2
I/O 3
Functional Block Diagram
6
5
4
Applications
•
•
•
•
•
•
•
•
LCD/PDP TVs
Monitors
Notebooks
10/100/1000 Ethernet
Firewire
Set Top Boxes
Flat Panel Displays
Portable Medical
10/100 Ethernet Differential Protection
Application Examples
10/100
Ethernet
PHY
Unused
TX +
USB Dual Port Protection
1
RT
TX -
USB
RX +
Controller
RT
2
5
3
4
3
D+
DGND
VCC
R
VCC
75
CT
VBUS
T
D+
D-
CT
RJ45
Unused
TX +
RX +
USB
Port
GND
10/100/1000 Ethernet Protection
TX -
Unused
75 VBUS75
RT
GND
10/100/1000
Ethernet
PHY
USB
Port
RX RX +
Unused
75
2
VBUS
SP3051-04HTG
CT
RX -
1
TX -
VBUS
6
SP3051-04HTG
VBUS
CT
RJ45
Unused
TX +
Unused
TX +
TX -
1
6
2
5
3
4
RX +
RX -
SP3051-04HTG
Unused
Unused
75
RX VCC
Life Support Note:
Not Intended for Use in Life Support or Life Saving Applications
The products shown herein are not designed for use in life sustaining or life saving
applications unless otherwise expressly indicated.
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/26/15
VCC
GND
To Twisted-Pair Network
I/O 1
• L
ow capacitance of 3.8pF
(TYP) per I/O
• Low leakage current of
0.5μA (MAX) at 5V
• Small SOT23-6 (JEDEC
MO-178AB) packaging
75
75
75
To Twisted-Pair Network
Pinout
• ESD, IEC61000-4-2,
±30kV contact, ±30kV air
• EFT, IEC61000-4-4, 40A
(5/50ns)
• Lightning, IEC61000-4-5,
20A (8/20μs)
SP3051
Description
TVS Diode Arrays (SPA® Diodes)
Lightning Surge Protection - SP3051 Series
Thermal Information
Absolute Maximum Ratings
Symbol
Parameter
Value
Parameter
Rating
Units
-55 to 150
°C
Maximum Junction Temperature
150
°C
Maximum Lead Temperature
(Soldering 20-40s)
260
°C
Units
IPP
Peak Current (tp=8/20μs)
20
A
PPK
Peak Pulse Power (tp=8/20μs)
400
W
TOP
Operating Temperature
-40 to125
°C
TSTOR
Storage Temperature
-55 to 150
°C
1
Storage Temperature Range
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress only rating and operation of the device
at these or any other conditions above those indicated in the operational sections of this
specification is not implied.
Electrical Characteristics (TOP=25ºC)
Parameter
Reverse Standoff Voltage
Symbol
Test Conditions
VRWM
IR ≤ 1µA
VR
IR = 1mA
ILEAK
VR=5V
Breakdown Voltage
Reverse Leakage Current
Min
Typ
Clamp Voltage
VC
RDYN
ESD Withstand Voltage1
VESD
Diode Capacitance1
CI/O-GND
Diode Capacitance1
CI/O-I/O
V
V
0.1
0.5
µA
2
9.0
10.5
V
IPP=10A, tp=8/20µs, I/O to GND
11.5
15.0
V
IPP=20A, tp=8/20µs, I/O to GND
14.3
17.0
V
(VC2 - VC1) / (IPP2 - IPP1)
0.3
2
2
Dynamic Resistance
Units
6.0
8.0
IPP=1A, tp=8/20µs, I/O to GND
1
Max
Ω
IEC61000-4-2 (Contact)
±30
kV
IEC61000-4-2 (Air)
±30
kV
Reverse Bias=0V
3.8
4.2
pF
Vcc=5V, Reverse Bias=2.5V
1.7
2.0
pF
Reverse Bias=0V
2.0
pF
Notes: 1 Parameter is guaranteed by design and/or device characterization.
2
Repetitive pulse per waveform shown on page 3.
Capacitance vs. Reverse Voltage
Clamping Voltage vs. Peak Pulse Current
5.0
15.0
Clamp Voltage (VC)
Capacitance (pF)
4.0
Vcc=0V
3.0
Vcc=5V
Vcc=3.3V
2.0
1.0
0.0
0.0
1.0
2.0
3.0
Bias Voltage (V)
4.0
5.0
10.0
5.0
0.0
1
5
10
15
20
Peak Pulse Current -IPP (A)
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/26/15
TVS Diode Arrays (SPA® Diodes)
Lightning Surge Protection - SP3051 Series
Product Characteristics
110%
Lead Plating
Matte Tin
100%
Lead Material
Copper Alloy
90%
Lead Coplanarity
0.0004 inches (0.102mm)
80%
Substitute Material
Silicon
Body Material
Molded Epoxy
Flammability
UL 94 V-0
70%
60%
50%
40%
30%
20%
10%
0%
0.0
5.0
10.0
15.0
20.0
25.0
30.0
Notes :
1. All dimensions are in millimeters
2. Dimensions include solder plating.
3. Dimensions are exclusive of mold flash & metal burr.
4. Blo is facing up for mold and facing down for trim/form, i.e. reverse trim/form.
5. Package surface matte finish VDI 11-13.
6. All specifications comply to JEDEC Spec MO-178AB Issue C
Time (μs)
Soldering Parameters
Transmission Line Pulsing(TLP) Plot
20
18
Pre Heat
TLP Current (A)
16
14
12
10
8
6
2
0
3
6
9
12
15
TLP Voltage (V)
Part Numbering System
SP 3051 – 04 H T G
TVS Diode Arrays
(SPA® Diodes)
Package
H: SOT23-6
Y* 4
Product Series
60 – 180 secs
3°C/second max
- Temperature (TL) (Liquidus)
217°C
- Temperature (tL)
60 – 150 seconds
Peak Temperature (TP)
260+0/-5 °C
Time within 5°C of actual peak
Temperature (tp)
20 – 40 seconds
Ramp-down Rate
6°C/second max
Time 25°C to peak Temperature (TP)
8 minutes Max.
Do not exceed
260°C
tP
TP
Critical Zone
TL to TP
Ramp-up
TL
TS(max)
tL
Ramp-do
Ramp-down
Preheat
TS(min)
tS
Number of Channels
25
Assembly Site
(Varies)
Ordering Information
Part Number
Package
Marking
Min. Order Qty.
SP3051-04HTG
SOT23-6
YH4
3000
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/26/15
200°C
- Time (min to max) (ts)
G= Green
Part Marking System
Y*4
- Temperature Max (Ts(max))
TS(max) to TL - Ramp-up Rate
Temperature
Number of
Channels
150°C
3°C/second max
T= Tape & Reel
Series
- Temperature Min (Ts(min))
Average ramp up rate (Liquidus) Temp
(TL) to peak
Reflow
4
0
Pb – Free assembly
Reflow Condition
time to peak temperature
Time
SP3051
Percent of IPP
Pulse Waveform
TVS Diode Arrays (SPA® Diodes)
Lightning Surge Protection - SP3051 Series
Package Dimensions — SOT23-6
Package
SOT23
Pins
6
JEDEC
MO-178AB
Millimeters
Min
Max
Max
Notes
A
0.900
1.450
0.035
0.057
-
0.000
0.150
0.000
0.006
-
A2
0.900
1.300
0.035
0.051
-
b
0.350
0.500
0.0138
0.0196
-
C
0.080
0.220
0.0031
0.009
-
D
2.800
3.000
0.11
0.118
3
E
2.600
3.000
0.102
0.118
-
E1
1.500
1.750
0.06
0.069
3
e
0.95 Ref
0.0374 ref
e1
1.9 Ref
0.0748 Ref
0.30
a
0.600
0.012
8º
0º
6
N
M
Min
A1
L
Recommended Solder Pad Layout
Inches
0º
-
0.023
6
4,5
6
8º
-
M
2.590
0.102
-
O
0.690
.027 TYP
-
P
0.990
.039 TYP
-
R
0.950
0.038
-
Notes:
1. Dimensioning and tolerancing Per ASME Y14.5M-1994.
2. Package conforms to EIAJ SC-74 (1992).
3. Dimensions D and E1 are exclusive of mold flash, protrusions, or gate burrs.
4. Foot length L measured at reference to seating plane.
5. “L” is the length of flat foot surface for soldering to substrate.
6. “N” is the number of terminal positions.
7. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact.
P
R
O
Embossed Carrier Tape & Reel Specification — SOT23-6
8mm TAPE AND REEL
1.5mm
DIA. HOLE
ACCESS HOLE
14.4mm
4.0mm
1.75mm
2.0mm
CL
8mm
4.0mm
13mm
180mm
GENERAL INFORMATION
SOT-23 (8mm POCKET PITCH)
1. 3000 PIECES PER REEL.
2. ORDER IN MULTIPLES OF FULL REELS ONLY.
3. MEETS EIA-481 REVISION "A" SPECIFICATIONS.
60mm
8.4mm
USER DIRECTION OF FEED
PIN 1
© 2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/26/15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement