MonnitLink Cellular Gateway
™
Quick Start Guide For Use With iMonnit Online Software
MonnitLink Cellular Gateway Quick Start
1. Create and setup your iMonnit™ account.
2. Connect and power on the gateway.
(International cellular gateways require additional
configuration. Please see International Cellular
Gateway quickstart guide.)
IMPORTANT!
DO NOT power up your cellular gateway until after you have created an
account on iMonnit.com and added your cellular gateway and wireless
sensors to the account. Also, when setting up your sensing network,
please make sure your sensors are at least 3-5 feet away from the gateway, and the sensors are at least 1 foot apart from each other.
Create and Setup Your iMonnit Account
• Visit http://www.imonnit.com to create an iMonnit online
sensor monitoring account.
MonnitLink Cellular Gateway Setup
• Attach the Antenna’s to the gateway (Sensor RF
antenna on left, Cellular antenna on right).
Sensor RF
Cellular
• Plug the power supply into a power outlet then connect
to the gateway.
• Turn the power switch on (battery backup models only)
• Check that the three LED lights on the front of the gateway change to green. Once all three lights turn green,
your network is ready to use.
• Follow the on-screen instructions to enter your account
and contact information.
Using Your Wireless Sensors
• You will be prompted to create your first sensor network.
Simply enter a name for your network.
• From the Overview Page of iMonnit, click “View
Gateways” and check that your gateway status has
changed to active.
• Next you will be prompted to add a wireless gateway
and wireless sensors to your network.
Contains FCC ID: ZTL-RFSC1
and IC: 9794A-RFSC1
• Enter the information from your MonnitLink™
gateway then click the “Assign Gateway” button.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful
interference and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
Pe
• Click on a sensor’s information to access detailed information for that sensor.
+
_
el
ID: ######
Code: XXXXXX
• From the Overview Page of iMonnit, click “View sensors” to return to the sensors overview page.
• Enter the information from your first wireless
Back of
Sensor
sensor then click the “Assign Sensor” button.
Contains: FCC ID: ZTL-RFSC1
IC: 9794A-RFSC1
Sensor ID: ######
Sensor Code: XXXXXX
• On the next screen, enter a name for the wireless sensor and use the drop down to tell us how you are going
to be using the wireless sensor. (This allows us to suggest settings for your sensor.) When finished, click the
“Continue” button.
•
Repeat these steps to add any additional wireless
sensors to your network.
• Click the “Edit” tab from a sensor’s detail view, to
change sensor settings.
• Insert batteries into the wireless sensors.
• Check that the sensors change to active as batteries are
inserted. (You may need to click the refresh button at
the top, right side of overview.)
• People to Notify - Select the user(s) to receive the
notification and click the arrow button to add them to the
recipient list. By default, email notifications are activated.
Clicking the notification delivery method icon toggles
them on and off (green is on, grey is off).
• The iMonnit online software is now collecting your
sensor data.
Note: Any change made to a sensor’s settings will be downloaded to
the sensor on the next sensor heartbeat (check-in). Once a change
has been made and “Saved,” you will not be able to edit that sensor’s
configurations again until the sensor has downloaded the new setting.
If you want to force a sensor to download new settings, you can power
cycle the sensor by removing the battery, waiting 30 seconds, then
reinsert the battery.
• Sent From - Assign devices (sensors and gateways) that
will cause the notification to be sent. When a notification
is sent from the system, it will automatically include the
device name and the data that caused the notification to
be sent. A single notification can be assigned to multiple
sensors or gateways.
Setting Up Sensor Notifications
• Notifications can be created, deleted or edited for any
sensor or group of sensors by clicking on “Notifications”
in the main menu.
Toggle On/Off
Click to Open Detail View
Send Test
Edit Delete
• Devices to Notify - If you have a Monnit Control or
Notifier A/V on your network, you will see a “Devices to
Notify” tab. This allows the notification to interact with
these devices. Add a device and click the control icons
to toggle their settings.
• When creating a notification, you will need to select the
type of notification to create.
• Sensor Reading Notification - Alert based on sensor reading
or sensing activity.
• Battery Notification - Alert based on battery power remaining.
• Inactivity Notification - Alert when a sensor has not checked in.
• Advanced Notifications - Alerts based on advanced rules, such
as comparing past data points with current ones.
• Existing Notifications - Use notifications that have already
been created on your account with the selected sensor.
• Notification Settings - Set notification parameters such
as name, message and sensor conditions that will cause
the notification to be sent.
Note: Control devices have two relays per device that are controlled
separately. You can turn a relay on, off or toggle the state. You can
also set a duration by clicking on the timer icon. This will perform the
selected toggle (on/off/toggle) for a set duration, then change back.
For more detailed instructions, documentation,
“how-to” guides and video demonstrations on using
Monnit wireless sensors, wireless gateways and
iMonnit software, visit our support page at
http://www.monnit.com/support/.
Monnit Corporation
4403 South 500 West
Murray, UT 84123
801-561-5555
www.monnit.com
Monnit, Monnit Logo, MonnitLink and iMonnit are trademarks of Monnit, Corp.
© 2009-2015 Monnit Corp. All Rights Reserved.
MQS-023-2D (09/15)
">
