Delfield 186114 BUC Installation manual

Delfield 186114 BUC Installation manual
International 18600 Series and CTP-NB
Service and Installation Manual
Please read this manual completely before attempting to install or operate this equipment! Notify carrier of damage! Inspect all
components immediately.
18600PTL
Pizza Tables with LiquiTec® Rail
18600PTB
Pizza Tables with Raised Rail
18600BST
Work Table with Backsplash
CAUTION
18600BUC
Work Tables
CTP-NB
Countertop Condiment Rail
Important Information
Read Before Use
Please Save These Instructions!
October 2013
International 18600 and CTP-NB Series Service and Installation Manual
Important Warning And Safety Information
WARNING
WARNING
WARNING
Failure To Follow Instructions In This Manual Can Cause Property Damage, Injury Or Death.
WARNING
Do Not Store Or Use Gasoline Or Other Flammable Vapors Or Liquids In The Vicinity Of This Or Any Other
Appliance.
WARNING
Unless All Cover And Access Panels Are In Place And Properly Secured, Do Not Operate This Equipment.
WARNING
This Appliance Is Not Intended For Use By Persons Who Lack Experience Or Knowledge, Unless They Have
Been Given Supervision Or Instruction Concerning Use Of The Appliance By A Person Responsible For Their
Safety.
WARNING
This Appliance Is Not To Be Played With.
WARNING
Do Not Clean With Water Jet.
WARNING
Do Not Use Electrical Appliances Inside The Food Storage Compartment Of This Appliance.
WARNING
Observe the following:
WARNING
WARNING
WARNING
WARNING
WARNING
Warning
WARNING
CAUTION
2
Read This Manual Thoroughly Before Operating, Installing, Or Performing Maintenance On The Equipment.
•
Minimum clearances must be maintained from all walls and combustible materials.
•
Keep the equipment area free and clear of combustible material.
•
Allow adequate clearance for air openings.
•
Operate equipment only on the type of electricity indicated on the specification plate.
•
Unplug the unit before making any repairs.
•
Retain this manual for future reference.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
International 18600 and CTP-NB Series Service and Installation Manual
Contents
Receiving & Inspecting Equipment............................................ 3
Serial Number Information......................................................... 4
Warranty Information.................................................................. 4
Regulatory Certifications............................................................. 4
Specifications.............................................................................. 5
Installation .................................................................................. 6
Operation
18600BUC & BST Series......................................................... 6
18600PTB & PTL Series.......................................................... 7
CTP-NB Series......................................................................... 7
Pressure Control Settings........................................................... 8
Temperature Control Settings..................................................... 8
Care And Cleaning..................................................................9-10
Wiring Diagram
18600PTB & PTL Series........................................................11
18600BUC & BST Series.......................................................12
CTP-NB Series.......................................................................12
Replacement Parts...............................................................13-20
Standard Labor Guidelines.......................................................21
Notes....................................................................................22-23
Receiving And Inspecting The Equipment
Even though most equipment is shipped crated, care should be
taken during unloading so the equipment is not damaged while
being moved into the building.
1. Visually inspect the exterior of the package and skid or
container. Any damage should be noted and reported to
the delivering carrier immediately.
2. If damaged, open and inspect the contents with the
carrier.
3. In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment
notify the carrier. Notification should be made verbally as
well as in written form.
4. Request an inspection by the shipping company of the
damaged equipment. This should be done within 10 days
from receipt of the equipment.
5. Check the lower portion of the unit to be sure legs or
casters are not bent.
6. Also open the compressor compartment housing and
visually inspect the refrigeration package. Be sure lines
are secure and base is still intact.
7. Freight carriers can supply the necessary damage forms
upon request.
8. Retain all crating material until an inspection has been
made or waived.
Uncrating the Equipment
First cut and remove the banding from around the crate.
Remove the front of the crate material, use of some tools will
be required. If the unit is on legs remove the top of the crate
and lift the unit off the skid. If the unit is on casters it can be
"rolled" off the skid.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
3
International 18600 and CTP-NB Series Service and Installation Manual
Serial Number Information
The serial number on 18600 Series units is located on the
electrical specifications tag affixed inside the compressor
section next to the pressure control.
The serial number on CTP-NB Series units is located on the
front of the unit.
Always have the serial number of your unit available when
calling for parts or service.
Warranty may be deemed invalid if other than
authorized OEM (original equipment manufacture)
replacement parts are used in Delfield equipment.
©2013 The Delfield Company. All rights reserved. Reproduction without
written permission is prohibited. “Delfield” is a registered trademark of The
Delfield Company.
Warranty Information
Visit http://www.delfield.com/minisite/service/warranty_info to:
• Register your product for warranty.
• Verify warranty information.
• View and download a copy of your warranty.
Regulatory Certifications
Models are certified by:
National Sanitation Foundation (NSF)
Technical Inspection Association
European Conformity
4
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
International 18600 and CTP-NB Series Service and Installation Manual
Specifications
18600PTB Pizza tables with raised rail
Custom
Model
1/3 Pan Size
Capacity
# Of Doors
# Of
Shelf Max
Shelf
Storage
Shelves Load (KG) Area CM2 Cap. L
BTU Load
Base/Rail
BTU Sys. Cap.
Base/Rail
H.P.
R404A
Charge
(oz/g)
Voltz/Hertz/
Phase
Amps
Ship Weight
LBS/KG
18648PTB-E
6
(1) 68.6cm
1
56
3670
290
470/441
2001/952
1/4
16/454
230-240/50/1
2.5
520/236
18660PTB-E
7
48.3cm &
68.6cm
2
32/56
6048
428
694/617
2409/1208
1/3
24/680
230-240/50/1
2.8
575/260
18672PTB-E
9
(2) 68.6cm
2
56
7339
513
776/794
2967/1587
1/2
40/1134 230-240/50/1
5.3
635/288
18691PTB-E
11
(2)68.6cm &
(1) 48.3cm
3
56/32
9560
693
1062/1058
3537/1865
1/2
40/1134 230-240/50/1
5.3
770/350
18699PTB-E
12
(3) 68.6cm
3
56
11009
778
1144/1147
3537/1945
1/2
40/1134 230-240/50/1
5.3
805/365
186114PTB-E
14
(3) 81.3cm
3
64
13434
936
1297/1323
5169/2433
3/4
48/1361 230-240/50/1
5.0
927/420
18600BUC Work tables
Custom
Model
# Of Doors
# Of
Shelf Max
Shelf
Storage
Shelves Load (KG) Area CM2 Cap. L
BTU Load
Base/Rail
BTU Sys. Cap.
Base/Rail
H.P.
R404A
Charge
(oz/g)
Voltz/Hertz/
Phase
Amps
Ship Weight
LBS/KG
18648BUC-E
(1) 68.6cm
1
56
3670
290
475/NA
1462/NA
1/4
16/454
230-240/50/1
2.5
390/177
18660BUC-E
48.3cm &
68.6cm
2
32/56
6048
428
686/NA
1462/NA
1/3
24/680
230-240/50/1
2.8
435/197
18672BUC-E
(2) 68.6cm
2
56
73390
513
856/NA
2261/NA
1/2
40/1134 230-240/50/1
5.3
495/225
18691BUC-E
(2)68.6cm &
(1) 48.3cm
3
56/32
9560
693
1169/NA
2261/NA
1/2
40/1134 230-240/50/1
5.3
535/243
18699BUC-E
(3) 68.6cm
3
56
11009
778
1220/NA
2591/NA
1/2
40/1134 230-240/50/1
5.3
594/269
186114BUC-E
(4) 61.0cm
4
48
13434
1055
1373/NA
2591/NA
3/4
48/1361 230-240/50/1
5.0
685/310
18600BST Work table with backsplash
Custom
Model
# Of Doors
# Of
Shelf Max
Shelf
Storage
Shelves Load (KG) Area CM2 Cap. L
BTU Load
Base/Rail
BTU Sys. Cap.
Base/Rail
H.P.
R404A
Charge
(oz/g)
Voltz/Hertz/
Phase
Amps
Ship Weight
LBS/KG
18648BST-E
(1) 68.6cm
1
56
3670
290
475/NA
1462/NA
1/4
16/454
230-240/50/1
2.5
390/177
18660BST-E
48.3cm &
68.6cm
2
32/56
6048
428
686/NA
1462/NA
1/3
24/680
230-240/50/1
2.8
435/197
18672BST-E
(2) 68.6cm
2
56
73390
513
856/NA
2261/NA
1/2
40/1134 230-240/50/1
5.3
495/225
18691BST-E
(2)68.6cm &
(1) 48.3cm
3
56/32
9560
693
1169/NA
2261/NA
1/2
40/1134 230-240/50/1
5.3
535/243
18699BST-E
(3) 68.6cm
3
56
11009
778
1220/NA
2591/NA
1/2
40/1134 230-240/50/1
5.3
594/269
186114BST-E
(4) 61.0cm
4
48
13434
1055
1373/NA
2591/NA
3/4
48/1361 230-240/50/1
5.0
685/310
18600PTL Pizza table with LiquiTec® rail
Custom
Model
1/3 Pan Size
Capacity
# Of Doors
# Of
Shelf Max
Shelf
Storage
Shelves Load (KG) Area CM2 Cap. L
BTU Load
Base/Rail
BTU Sys. Cap.
Base/Rail
H.P.
R404A
Charge
(oz/g)
Voltz/Hertz/
Phase
Amps
Ship Weight
LBS/KG
18648PTL-E
6
(1) 68.6cm
1
56
3670
290
470/441
2001/952
1/4
16/454
230-240/50/1
2.5
520/236
18672PTL-E
9
(2) 68.6cm
2
56
7339
513
776/794
2967/1587
1/2
40/1134 230-240/50/1
5.3
635/288
18699PTL-E
12
(3) 68.6cm
3
56
11009
778
1144/1147
3537/1945
1/2
40/1134 230-240/50/1
5.3
805/365
CTP-NB Counter top containment rail
Custom
Model
1/3 Pan Size
Capacity
# Of Adapter Bars
BTU Load
BTU System
Capacity
H.P.
R134A
Charge
(oz/g)
Voltz/Hertz/
Phase
Amps
Ship Weight
LBS/KG
CTP8146-NB-E
4
5
305
523
1/4
16/454
230-240/50/1
2.5
121/54.9
CTP8160-NB-E
6
7
462
653
1/4
16/454
230-240/50/1
2.5
158/71.7
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
5
International 18600 and CTP-NB Series Service and Installation Manual
Installation
Location
These units are intended for indoor use only. Be sure the location
chosen has a floor strong enough to support the total weight of the
cabinet and contents. A fully loaded 72” (183cm) long model may
weigh as much as 1200 pounds (544kg). Reinforce the floor as
necessary to provide for maximum loading.
Plumbing
Self-contained models are standard with a condensate evaporator. If,
for some reason, a unit does not have a condensate evaporator, or the
evaporator fails, the unit’s drain must have an outlet to an appropriate
drainage area or container.
For the most efficient refrigeration, be sure to provide good air
circulation inside and out.
CAUTION
Inside cabinet: Do not pack refrigerator so full that air cannot
circulate.
Outside cabinet: Be sure that the unit has access to ample air. Avoid
hot corners and locations near stoves and ovens.
It is recommended that the unit be installed no closer than 1” (25mm)
from any wall. PDL models also require 14” (36cm) clearance at the
top and 6” (15cm) clearance at the bottom (casters).
Electrical connection
Refer to the amperage data, the serial tag, your local code or the
National Electrical Code to be sure the unit is connected to the proper
power source. A protected circuit of the correct voltage and amperage
must be run for con­nec­tion of the line cord, or permanent connection
to the unit.
Leveling
A level cabinet looks better and will perform better because the drain
pan will drain properly, the doors will line up with the frames properly,
and the cabinet will not be subject to undue strain.
Some models have casters for your convenience, for ease of cleaning
underneath and for mobility. It is important that the unit be installed
in a stable condition with the front casters locked before operating.
Moisture collecting from improper drainage can create
a slippery surface on the floor and a hazard to
employees. It is the owner’s responsibility to provide
a container or outlet for drainage.
DANGER
The power switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service or maintenance functions.
Never operate the unit without the louvered panel in
place!
Operation: 18600BUC & BST Series
After turning the ON/OFF switch to ON, the units compressor will
begin operating. Delfield refrigerated bases are designed to maintain
an operational temperature of 36°F to 40°F (2°C to 4°C).
CAUTION
Product should be loaded into the unit with care.
Failure to heed these recommendations could result in
damage to the interior of the cabinet or the blower coil.
Overloading the storage area, restricting the air flow
and continuous opening and closing of the doors and
drawers will hamper the units ability to maintain
operational temperature.
Refrigerator Evaporator Fan Operation
When the refrigerator is initially powered up or immediately following
a power outage the unit will begin cooling after a 3-6 minute delay.
During normal operation the evaporator fan pulses independently of
the compressor as dictated by the controller as follows:
1.
During the cooling mode, compressor and evaporator fan run
simultaneously.
2.
During the compressor off mode, evaporator fan pulses three
minutes on and three minutes off.
3.
During an actual defrost event other than the off-cycle defrost,
compressor stays off but the evaporator fan runs continuously.
Cooling Cycle
Compressor On
Evap Fan
On
Evap Fan
Off
X
6
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Defrost Cycle
Compressor Off
Evap Fan
On
Evap Fan
Off
Cycles On 3-Min, Off
3-Min
Compressor Off
Evap Fan
On
X
Evap Fan
Off
International 18600 and CTP-NB Series Service and Installation Manual
Operation: 18600PTB & PTL Series
CAUTION
Product should be loaded into the unit with care.
Failure to heed these recommendations could result in
damage to the interior of the cabinet or the blower coil.
This unit is equipped with two on/off switches located behind the
louvered machine compartment panel. The unit’s com­pres­sor and all
evaporator fans will begin op­er­at­ing when the main power switch is
turned to the ON position. Tem­per­a­ture ranges for the base are 36°F
to 40°F (2°C to 4°C).
The switch labeled rail is for the raised rail. The rail switch is
accessible through a 1.5” (4cm) diameter hole in the louvered panel.
Turning this switch to the ON position will activate the refrigeration
for the rail. Temperature ranges for the raised rail are 33°F to 41°F
(1°C to 5°C).
Product located in the rail must be removed at the end
of day. This allows you to turn the rail off at night to
save energy and the rail will have time to defrost as
needed.
A minimum of one hour of off time per day with the pans removed
from the rail is required to properly defrost the rail.
DANGER
The power must be turned to OFF and the unit
disconnected from the power source whenever
performing service or maintenance functions.
Never operate the unit without the louvered panel in
place!
All R404A models have a high pressure limiting device. Under
severe overloading conditions, or in the event of a condenser fan
failure or a plugged or blocked condenser, this device may shut
down the refrigeration system. This device will automatically reset,
but determining the cause of the high pressure condition should be
investigated by a qualified refrigeration technician.
Refrigerator Evaporator Fan Operation
When the refrigerator is initially powered up or immediately following
a power outage the unit will begin cooling after a 3-6 minute delay.
During normal operation the evaporator fan pulses independently of
the compressor as dictated by the controller as follows:
1.
During the cooling mode, compressor and evaporator fan run
simultaneously.
2.
During the compressor off mode, evaporator fan pulses three
minutes on and three minutes off.
3.
During an actual defrost event other than the off-cycle defrost,
compressor stays off but the evaporator fan runs continuously.
Cooling Cycle
Compressor On
Evap Fan
On
X
Evap Fan
Off
Defrost Cycle
Compressor Off
Evap Fan
On
Evap Fan
Off
Cycles On 3-Min, Off
3-Min
Compressor Off
Evap Fan
On
Evap Fan
Off
X
Operation: ctp-nb Series
The unit is equipped with one on/off switch located on the right
end of the unit. The unit’s com­pres­sor will begin op­er­at­ing when
this switch is turned to the ON position. Tem­per­at­ure ranges for the
rail are 33°F to 41°F (1°C to 5°C).
Product located in the rail must be removed at the
end of day. This allows you to turn the rail OFF at
night to save energy and the rail will have time to
defrost as needed.
A minimum of one hour of off time per day with the pans removed
from the rail is required to properly defrost the rail.
CAUTION
The power switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service or maintenance functions.
Never operate the unit without the louvered panel in
place!
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
7
International 18600 and CTP-NB Series Service and Installation Manual
Pressure Control Settings
The factory recommended low-pressure control settings
for 18600PTB’s are: 55psi cut-in and 30psi cut-out to
maintain proper temperature for product in the rail. The
interior temperature is controlled by the thermostat mounted
in the mechanical compartment.
The factory recommended low-pressure control settings
for 18600PTL’s are: 20psi (1.38bar) cut-in and 10psi
(0.70bar) cut-out. The base and rail temperatures are
controlled by the thermostats mounted in the machine
compartment.
A pressure control is located in the machine compartment.
An adjustable control has the word COLDER on the knob,
with an arrow to indicate the adjustment direction. These
controls are field adjustable and do not require a service
agent.
In attempting to adjust the pressure control,
you can do damage to your unit by accidentally
adjusting the differential. Please make small
incremental adjustments if a temperature
adjustment is necessary. It may take an hour
or longer to realize the temperature change
depending on the application and location of the
unit.
Please contact the service department at Delfield
(800) 733-8829 or your local service agent.
Delfield is not responsible for charges incurred
while having the pressure control adjusted.
Temperature Control Settings
A thermostat controls temperature in the 18600PTB base,
18600PTL base, 18600PTL rail, BUC and BST.
Thermostats are located in the machine compartment. They
are field adjustable and do not require a service agent. The
factory setting is 2.5. Set toward 1 for higher temperatures
and toward 7 for lower temperatures.
8
Please make small incremental adjustments if
a temperature adjustment is necessary. It may
take an hour or longer to realize the temperature
change depending on the application and location
of the unit.
Contact the service department at Delfield +1
(989) 773-7981 or your local service agent
for additional assistance. Delfield is not
responsible for charges incurred while adjusting
the thermostat.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
International 18600 and CTP-NB Series Service and Installation Manual
Care & Cleaning
Door Gasket Maintenance
Door gaskets require regular cleaning to prevent mold and mildew
build up and also to retain the elasticity of the gasket. Gasket cleaning
can be done with the use of warm soapy water. Avoid full strength
cleaning products on gaskets as this can cause them to become
brittle and crack. Never use sharp tools or knives to scrape or clean
the gasket. Gaskets can be easily replaced and do not require the use
of tools or an authorized service person. The gaskets are “Dart” style
and can be pulled out of the groove in the door and new gaskets can
be “pressed” back into place.
in place automatically. Once all tracks are replaced, insert the drawer
box. Rest the drawer box bottom track on the front track roller. Then
push the drawer back in place SLOWLY. When the drawer box is about
half way in you will hit a STOP. You must lift the front of the drawer up
approximately ½” (1.3cm) to continue inward. Clean tracks as often
as possible. The cleaner the tracks are the better they will operate.
Caster Maintenance
Wipe casters with a damp cloth monthly to prevent corrosion.
The power switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service, maintenance functions or cleaning
the refrigerated area.
Drain Maintenance - Base
Each unit has a drain located inside the unit that removes the
condensation from the evaporator coil and routes it to an external
condensate evaporator pan. Each drain can become loose or
disconnected during normal use. If you notice water accumulation
on the inside of the unit be sure the drain tube is connected to the
evaporator drain pan. If water is collecting underneath the unit make
sure the end of the drain tube is in the condensate evaporator in the
machine compartment. The leveling of the unit is important as the
units are designed to drain properly when level. Be sure all drain lines
are free of obstructions.
Drawer Maintenance
Drawer Assembly Cleaning
The drawer assembly is designed to be cleaned easily. Both drawer
and tracks are removable without tools. The drawer tracks are
dishwasher safe or can be cleaned in a sink with detergents and a
soft bristle brush. Drawers and tracks should be cleaned on a weekly
basis.
Remove Drawers
Pull the drawer box out until it stops. Lift up on the drawer front and
pull the drawer box completely out. Using a soft bristle brush, clean
the track on the bottom of the drawer box. When finished, it should
be wiped clean of all food and debris.
Tracks
The drawer box assembly must be removed. Pull the drawer tracks
out until they hit a stop. Locate blue safety clips towards the back
of each drawer track. Blue safety clips have a tab on the top. Push
the tab back until it clicks.
Lift up and pull the drawer
tracks all the way out of the
drawer cage. The drawer
tracks are dishwasher safe
tab on top of
or can be cleaned in a sink
blue safety clip with detergents and a soft
bristle brush. Drawers and
tracks should be cleaned on a weekly basis. Using a soft bristle brush,
wash the track making sure each roller is thoroughly cleaned. The
drawer cage should be cleaned with a soft bristle brush, removing
any food and debris gathered on the bottom ledge. Once it’s cleaned
thoroughly with a soft bristle brush, wipe remaining debris clean with
a soft towel.
Reassembly
Push the drawer tracks into the drawer cage. The blue safety clip
must remain pushed towards the back. Lift up and slide the drawer
track all the way into the drawer cage. The blue safety clip will lock
Refrigerators and Freezers
The interior and exterior can be cleaned using soap and warm water.
If this isn’t sufficient, try ammonia and water or a nonabrasive liquid
cleaner. When cleaning the exterior, always rub with the “grain” of
the stainless steel to avoid marring the finish. Do not use an abrasive
cleaner because it will scratch the stainless steel and can damage the
breaker strips and gaskets.
Stainless Steel Care and Cleaning
To prevent discoloration of rust on stainless steel several important
steps need to be taken. First, we need to understand the properties
of stainless steel. Stainless steel contains 70- 80% iron, which will
rust. It also contains 12-30% chromium, which forms an invisible
passive film over the steels surface, which acts as a shield against
corrosion. As long as the protective layer is intact, the metal is still
stainless. If the film is broken or contaminated, outside elements
can begin to breakdown the steel and begin to form discoloration of
rust. Proper cleaning of stainless steel requires soft cloths or plastic
scouring pads.
NEVER USE STEEL PADS, WIRE BRUSHES OR SCRAPERS!
Cleaning solutions need to be alkaline based or non-chloride cleaners.
Any cleaner containing chlorides will damage the protective film of
the stainless steel. Chlorides are also commonly found in hard water,
salts, and household and industrial cleaners. If cleaners containing
chlorides are used be sure to rinse repeatedly and dry thoroughly.
Routine cleaning of stainless steel can be done with soap and water.
Extreme stains or grease should be cleaned with a non-abrasive
cleaner and plastic scrub pad. Always rub with the grain of the
steel. There are stainless steel cleaners available which can restore
and preserve the finish of the steels protective layer. Early signs of
stainless steel breakdown are small pits and cracks. If this has begun,
clean thoroughly and start to apply stainless steel cleaners in attempt
to restore the passivity of the steel.
CAUTION
Never use an acid based cleaning solution! Many food
products have an acidic content, which can deteriorate
the finish. Be sure to clean the stainless steel surfaces
of ALL food products. Common items include, tomatoes,
peppers and other vegetables.
Cleaning the Condenser Coil
In order to maintain proper refrigeration performance, the
condenser fins must be cleaned of dust, dirt and grease regularly.
It is recommended that this be done at least every three months.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
9
International 18600 and CTP-NB Series Service and Installation Manual
Care & Cleaning, continued
If conditions are such that the condenser is totally blocked in three
months, the frequency of cleaning should be increased. Clean the
condenser with a vacuum cleaner or stiff brush. If extremely dirty, a
commercially available condenser cleaner may be required.
Continuous opening and closing of the doors will hamper the unit’s
ability to maintain optimum refrigeration temperature. Top section is
not intended for overnight storage. Product should be removed from
pans. Pans can remain in unit while empty.
Failure to maintain a clean condenser coil can initially cause high
temperatures and excessive run times. Continuous operation with
a dirty or clogged condenser coil can result in compressor failure.
Neglecting the condenser coil cleaning procedures will void any
warranties associated with the compressor and cost to replace the
compressor.
CAUTION
Never use a high-pressure water wash for this
cleaning procedure as water can damage the electrical
components located near or at the condenser coil.
Doors/Hinges
Over time and with heavy use doors the hinges may become loose. If
this happens tighten the screws that mount the hinge brackets to the
frame of the unit. Loose or sagging doors can cause the hinges to pull
out of the frame, which may damage both the doors and the hinges. In
some cases this may require qualified service agents or maintenance
personnel to perform repairs.
Do not place hot pans on/against the blue ABS liner.
Do not throw items into the storage area. Failure to
follow these recommendations could result in damage
to the interior of the cabinet or to the blower coil.
Overloading the storage area, restricting the airflow,
and continuous opening and closing of the doors and
drawers will hamper the units ability to maintain
operational temperature.
Refrigerated rail units
Product in the rail should be removed to the refrigerated base at the
end of the day. This allows you to turn the rail off at night to save
energy and to defrost the rail. It also helps maintain product quality.
The standard wrapped refrigerated rail units are controlled by a lowpressure control that is set to maintain the proper rail temperature.
An on/off switch is also provided for the rail and is required to be shut
off at night. With a LiquiTec rail a thermostat is provided to maintain
rail temperature as well as the rail on/off switch. The LiquiTec rail
is required to be shut off at night as well to allow for defrosting. To
ensure product quality in the rail it is recommended that product be
rotated every four hours.
If adding any item to the unit, be sure to keep in mind
the location of the refrigeration lines on wrapped rail
units. A refrigeration leak in a rail is extremely difficult
and costly to repair. In some cases it cannot be repaired
at all.
Preventing blower coil corrosion
To help prevent corrosion of the blower coil, store all acidic items,
such as pickles and tomatoes, in sealable containers. Immediately
wipe up all spills.
DANGER
10
Units with pans should be operated with pans in place.
Operating the unit without all pans in place will lower
efficiency and may damage the unit.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
International 18600 and CTP-NB Series Service and Installation Manual
Wiring Diagram - 18600PTB Series
Wiring Diagram - 18600PTL Series
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
11
International 18600 and CTP-NB Series Service and Installation Manual
Wiring Diagram - 18600BUC & BST Series
Wiring Diagram - ctp-nb series
N
L1
Power Switch
Condensing Unit
Temperature Controls The Condensing Unit
12
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
G
International 18600 and CTP-NB Series Service and Installation Manual
18600PTB Replacement Parts
All 18600PTB Models
3234290
1" Shelf Support
9321132
1.5" Shelf Support Screw
3234198
Caster, 5, Plate ,Swivel
3234199
Caster, 5, Plate, Swivel, Break
3234392
Hinge, Pan Cover, Center
3234282
Hinge, Pan Cover, End, LH
3234266
Hinge, Pan Cover, End, RH
MCP00145
Low Pressure Control
2194400
Switch, Rocker, 20A/125V,
186114PTB
18699PTB
*000-BN5-003J
Assembly, 1/4 HP Condensing Unit
*000-BN5-003M
Assembly, 1/3 Condensing Unit
*000-BN5-003O
Assembly, 1/2 HP Condenser, Med
*000-BN5-003Q
Assembly, 3/4 HP Condenser, Med
*000-187-007Y
Assembly, Dr, Ref, 19X26, LT, 430
*000-187-007X
Assembly, Dr, Ref, 19X26, RT, 430
*000-187-0082
Assembly, Dr, Ref, 27X26, LT, 430
X
*000-187-0081
Assembly, Dr, Ref, 27X26, RT,430
X
*000-187-0084
Assembly, Dr, Ref, 32X26, LT, 430
X
*000-187-0083
Assembly, Dr, Ref, 32X26, RT, 430
X
*000-402-004Q
Assembly, Hinged Cover, 6 Pan, RT
*000-402-004V
Assembly, Hinged Cover, 8 Pan
*000-402-004U
Assembly, Hinged Cover, 8 Pan, RT
*000-402-004X
Assembly, Hinged Cover, 10 Pan, LT
X
*000-402-004Y
Assembly, Hinged Cover, 10 Pan, RT
X
*000-402-0050
Assembly, Hinged Cover, 12 Pan
*000-402-0051
Assembly, Hinged Cover, 12 Pan, LT
X
*000-402-0052
Assembly, Hinged Cover, 12 Pan, RT
X
*000-248-0033
Coil Assembly, R404A
*000-248-003D
Coil Assembly, R404A, Fan Lt
*359-478-003C
Panel, Louver, 14.0, PTB
*359-478-003E
Panel, Louver, 15.0, PTB
*359-478-003D
Panel, Louver, 18.0, PTB
3977984
Shelf, Wire, 19X32DP
3977983
Shelf, Wire, 32X32 DP
3978014
Shelf, Wire, Coated
18691PTB
18672PTB
18660PTB
18648PTB
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
*Exploded assemblies and part prints are on the following pages.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
13
International 18600 and CTP-NB Series Service and Installation Manual
18600BUC Replacement Parts
All 18600BUC Models
3234290
1" Shelf Support
9321132
1.5" Shelf Support Screw
3234198
Caster, 5, Plate, Swivel
3234199
Caster, 5, Plate, Swivel, Brake
000-282-007U
Control Assembly, Defrost, 220V, Ref
2194400
Switch, Rocker, 20A/125V,
*000-BN5-003I
Assembly, 1/5 Condensing Unit
*000-BN5-003J
Assembly, 1/4 HP Condensing Unit
*000-BN5-003M
Assembly, 1/3 Condensing Unit
*000-187-007Y
Assembly, Dr, Ref, 19X26, LT, 430
*000-187-007X
Assembly, Dr, Ref, 19X26, RT, 430
*000-187-0082
Assembly, Dr, Ref, 27X26, LT, 430
*000-187-0081
Assembly, Dr, Ref, 27X26, RT, 430
*000-187-0084
Assembly, Dr, Ref, 32X26, LT, 430
X
*000-187-0083
Assembly, Dr, Ref, 32X26, RT, 430
X
*000-248-0033
Coil Assembly, R404A
X
*000-248-003D
Coil Assembly, R404A, Fan Lt
*359-478-0040
Panel, Louver, 14, Hanging
*359-478-0042
Panel, Louver, 15, Hanging
*359-478-0041
Panel, Louver, 18, Hanging
3977984
Shelf, Wire, 19X32DP
3977983
Shelf, Wire, 32X32DP
3978014
Shelf, Wire, Coated
186114BUC
18699BUC
X
X
18672BUC
18660BUC
18648BUC
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
*Exploded assemblies and part prints are on the following pages.
14
18691BUC
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
X
X
X
X
International 18600 and CTP-NB Series Service and Installation Manual
18600BST & 18600PTL Replacement Parts
All 18600BST Models
3234290
1" Shelf Support
9321132
1.5" Shelf Support Screw
3234198
Caster, 5, Plate, Swivel
3234199
Caster, 5, Plate, Swivel, Brake
000-282-007U
Control Assembly, Defrost, 220V, Ref
2194400
Switch, Rocker, 20A/125V,
186114BST
*000-BN5-003I
Assembly, 1/5 Condensing Unit
*000-BN5-003J
Assembly, 1/4 HP Condensing Unit
18699BST
18691BST
18672BST
X
X
X
18660BST
18648BST
X
X
*000-BN5-003M
Assembly, 1/3 Condensing Unit
*000-187-007Y
Assembly, Dr, Ref, 19X26, LT, 430
X
*000-187-007X
Assembly, Dr, Ref, 19X26, RT, 430
*000-187-0082
Assembly, Dr, Ref, 27X26, LT, 430
X
X
X
*000-187-0081
Assembly, Dr, Ref, 27X26, RT, 430
X
X
X
X
*000-187-0084
Assembly, Dr, Ref, 32X26, LT, 430
X
*000-187-0083
Assembly, Dr, Ref, 32X26, RT, 430
X
*000-248-0033
Coil Assembly, R404A
X
X
X
X
X
*000-248-003D
Coil Assembly, R404A, Fan Lt
*359-478-0040
Panel, Louver, 14, Hanging
*359-478-0042
Panel, Louver, 15, Hanging
*359-478-0041
Panel, Louver, 18, Hanging
3977984
Shelf, Wire, 19X32DP
3977983
Shelf, Wire, 32X32DP
3978014
Shelf, Wire, Coated
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
All 18600PTL Models
3234290
1" Shelf Support
MCP00142
Coil, Solenoid, 240V, Danfoss
9321132
1.5" Shelf Support Screw
3234392
Hinge, Pan Cover, Center
*000-187-0082
Assembly, Dr, Ref, 27X26, LT, 430
3234282
Hinge, Pan Cover, End, LH
*000-402-0055
Assembly, Hinged Cover, 12 Pan, PTL
3234266
Hinge, Pan Cover, End, RH
263-ASB-0030
Bracket, Cutting Board, Center
3978014
Shelf, Wire, Coated
263-110-0034
Bracket, Cutting Board, LH
MCP00158
Solenoid Valve Connector
263-110-0036
Bracket, Cutting Board, RF
2194400
Switch, Rocker, 20A/125V,
3234198
Caster, 5, Plate, Swivel
MCP00140
Valve, Expansion, R404A, Danfoss
3234199
Caster, 5, Plate, Swivel, Brake
MCP00141
Valve, Solenoid, 24OV, Danfoss
18699PTL
18672PTL
*000-BN5-003J
Assembly, 1/4 HP Condensing Unit
*000-BN5-003O
Assembly, 1/2HP Condenser, MED
X
X
*000-187-0081
Assembly, Dr, Ref, 27X26, RT, 430
X
X
*000-402-0054
Assembly, Hinged Cover, 6 Pan, PTL
*000-248-0033
Coil Assembly, R404A
*000-248-003D
Coil Assembly, R404A, Fan Lt
18648PTL
X
X
X
X
X
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
15
International 18600 and CTP-NB Series Service and Installation Manual
CTP8000-NB Replacement Parts
All CTP8000-NB Models
243-ALS-0032
Divider, Bar, Cold
3234392
Hinge, Pan Cover, Center
3234282
Hinge, Pan Cover, End, LH
3234266
Hinge, Pan Cover, End, RH
9321374
Pin, Hinge, Salad Pan
*000-BN5-003J
Condensing Unit Assembly, 1/4HP, CTP
*223-016-Z000P
Cover, Hinged, CTP
*312-016-003U
Cover, Pan, Rail, 8 Pan
*312-016-003W
Cover, Pan, Rail, 12 Pan
243-ALS-0030
Divider, Bar, Cold
243-ALS-0036
Divider, Bar, Cold
*356-411-Z0009
Louver, Front, CTP-8100
*026-411-Z000A
Louver, Rear, CTP-8100
*356-411-0004
Panel, Louver, Front CTP-8100
CTP8160-NB
CTP8146-NB
X
X
X
X
X
X
X
X
*Exploded assemblies and part prints are on the following pages.
16
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
International 18600 and CTP-NB Series Service and Installation Manual
Replacement Parts - Condensing Unit Assemblies
2
2
3
3
4
1
4
1
5
5
6
6
7
7
8
8
-
000-BN5-003I
Assembly, 1/5 Condensing Unit, 220/50
Key
Part Number
Description
1
2160029
Fan, Axial, 5.5”, 230V
-
000-BN5-003J
Assembly, 1/4 HP Condensing Unit, 220V/50Hz
2
2160030
Guard, Fan, 6.0”
1
2160029
Fan, Axial, 5.5”, 230V
3
026-C58-0037
Shroud, Condenser Coil
2
2160030
Guard, Fan, 6.0”
4
3526994
Compressor, Danfoss, TL4CL
3
026-C58-0037
Shroud, Condenser Coil
5
3516451
Start Capacitor
4
3527013
Compressor, Danfoss, 220V, 50Hz
6
3516322
Filter Dryer
5
Danfoss #117U5015
Start Capacitor
7
039-231-0030
Condensate Pan
6
3516322
Filter Dryer
8
3516454
Condenser Coil
7
039-231-0030
Condensate Pan
8
3516454
Condenser Coil
2
3
4
1
5
7
6
8
9
Key
Part Number
Description
-
000-BN5-003M
Assembly, 1/3 Condensing Unit, 220V/50Hz
1
2160029
Fan, Axial, 5.5”, 230V
2
2160030
Guard, Fan, 6.0”
3
026-C58-0037
Shroud, Condenser Coil
4
3527012
Compressor, Danfoss, NL8.4CLX, 220V, 50Hz
5
Danfoss #117U5015
Start Capacitor
6
3516322
Filter Drier
7
3516458
Receiver tank
8
039-231-0030
Pan, Condensate
9
3516454
Condenser Coil
-
3516324
High Pressure Cutout
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
17
International 18600 and CTP-NB Series Service and Installation Manual
Replacement Parts - Condensing Unit Assemblies
6
7
5
2
1
3
4
2
4
3
1
8
5
9
6
-
000-BN5-003O
7
10
11
Assembly, 1/2HP Condenser, Med, 220/50
Key
Part Number
Description
000-BN5-003Q
Assembly, 3/4 HP Condenser, Med
1
026-C58-0031
Shroud
-
2
3516554
Condenser fan blade
1
026-C58-003A
Shroud
2160019
Guard, Fan, Wire
3
2160019
Condenser fan guard
2
4
2162721
Condenser fan motor, 230V
3
Danfoss #117U5015
Capacitor, Start, Run, Assembly
Capacitor, start-run assy
4
3527022
Compressor, 3/4 HP Med, 220V/50Hz
3516322
Drier, Filter, (2)Inlet
5
Danfoss #117U5017
6
3527045
Compressor, Danfoss, SC12MLX, 220V/50Hz
5
7
3516331
Hi pressure switch
6
3516360
Receiver Tank
3516456
Coil, Condenser, 3/4 HP
8
3516322
Filter Drier
7
9
3516459
Receiver
-
3516433
Blade, Fan, 25Deg, 10", CW
3516331
Hi Pressure Switch
10
039-231-0031
Pan, Condensate
-
11
3516455
Condenser coil
-
2162721
Motor, Fan, 16W, 230V
-
039-231-0031
Pan, Condensate, Sm
18
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
International 18600 and CTP-NB Series Service and Installation Manual
Replacement Parts - Evaporator Coil Assembly
1
1
4
2
4
2
3
3
5
6
6
5
9
7
9
8
8
7
Key
1
2
3
4
5
6
7
8
9
-
Part Number
000-248-0033
2160024
2160025
3516095
030-232-0003
MCP00140
030-233-0001
000-BNH-0030
030-234-0003
030-233-0002
2184317
2194808
2194809
Description
Coil Assembly, R404A, Refg, 220V
Guard, fan, 4.7"
Fan, axiel, 230V
Coil, evaporator
Back, evaporator, enclosure
Expansion valve, R-404a
Side, coil, angled, Rt
Drip pan, evaporator
Front, coil
Side, coil, angled, Lt
Harness, coil
Probe, Defrost, Danfoss, Control
Probe, Temp, Sensor, Danfoss
Key
Part Number
Description
1
2
3
4
5
6
7
8
9
-
000-248-003D
2160024
2160025
3516095
030-232-0003
000-BNH-0030
030-233-0038
MCP00140
030-234-0003
030-233-0039
2184317
2194808
2194809
Coil Assembly, R404A, 220V, Fan Lt
Guard, fan, 4.7"
Fan, axiel, 230V
Coil, evaporator
Back, evaporator, enclosure
Drip pan, evaporator
Side, coil, angled, Rt, Blank
Expansion valve, R-404a
Front, coil
Side, Coil, Angled, Lt, 2Fan
Harness, coil
Probe, Defrost, Danfoss, Control
Probe, Temp, Sensor, Danfoss
Replacement Parts - Louvered Panels
Description
Part Number
Description
Part Number
Description
026-411-Z000A
Louver, Rear, CTP-8100
359-478-003C
Panel, Louver, 14.0, PTB
359-478-0040
Panel, Louver, 14, Hanging
356-411-0004
Panel, Louver, Front CTP-8100
359-478-003D
Panel, Louver, 18.0, PTB
359-478-0041
Panel, Louver, 18, Hanging
356-411-Z0009
Louver, Front, CTP-8100
359-478-003E
Panel, Louver, 15.0, PTB
359-478-0042
Panel, Louver, 15, Hanging
Part Number
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
19
International 18600 and CTP-NB Series Service and Installation Manual
Replacement Parts - Door & Cover Assemblies
2
1
1
2
Key
Part Number
Description
Part Number
Description
-
000-187-007X
Assembly, Dr, Ref, 19X26, RT, 430
000-402-004Q
Assembly, Hinged Cover, 6 Pan, RT
1
1701183
Gasket, Dr, 19, Mark7
000-402-004U
Assembly, Hinged Cover, 8 Pan, RT
2
0160179
Hinge Kit
000-402-004V
Assembly, Hinged Cover, 8 Pan
-
000-187-007Y
Assembly, Dr, Ref, 19X26, LT, 430
000-402-004X
Assembly, Hinged Cover, 10 Pan, LT
Assembly, Hinged Cover, 10 Pan, RT
1
1701183
Gasket, Dr, 19, Mark7
000-402-004Y
2
0160179
Hinge Kit
000-402-0050
Assembly, Hinged Cover, 12 Pan
-
000-187-0081
Assembly, Dr, Ref, 27X26, RT,430
000-402-0051
Assembly, Hinged Cover, 12 Pan, LT
1
1701185
Gasket, Dr, 27, Mark7
000-402-0052
Assembly, Hinged Cover, 12 Pan, RT
2
0160179
Hinge Kit
000-402-0054
Assembly, Hinged Cover, 6 Pan, PTL
-
000-187-0082
Assembly, Dr, Ref, 27X26, LT, 430
000-402-0055
Assembly, Hinged Cover, 12 Pan, PTL
1
1701185
Gasket, Dr, 27, Mark7
223-016-Z000P
Cover, Hinged, CTP
Cover, Pan, Rail, 8 Pan
Cover, Pan, Rail, 12 Pan
2
0160179
Hinge Kit
312-016-003U
-
000-187-0083
Assembly, Dr, Ref, 32X26, RT, 430
312-016-003W
1
1701186
32" Door Gasket
2
0160179
Hinge Kit
-
000-187-0084
Assembly, Dr, Ref, 32X26, LT, 430
1
1701186
32" Door Gasket
2
0160179
Hinge Kit
20
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
International 18600 and CTP-NB Series Service and Installation Manual
Standard Labor Guidelines To Repair Or Replace Parts On Delfield Equipment
Advice and recommendations given by Delfield Service Technicians do not constitute or guarantee any special coverage.
• A maximum of 1-hour is allowed to diagnose a defective component.
• A maximum travel distance of 100 miles round trip and 2-hours will be reimbursed. Actual travel to be charged.
• Overtime, installation/start-up, normal control adjustments, general maintenance, glass breakage, freight damage, and/or correcting and
end-user installation error will not be reimbursed under warranty unless pre-approved with a Service Work Authorization from Delfield.
You must submit the number with the service claim.
• Actual repair time will be paid at or below guidline.
• Parts on the critcal stock list must be air freighted at the expense of the service agent.
Labor Up To 1-Hour Is Allowed To Replace
• Infinite Switch
• Contactor/Relay
• Door Jamb Switch
• Transformer
• Solenoid Coil
• Evaporator/Condenser Fan Motor and Blade
• Hi-limit/Thermal Protector Switch
• Circulating Fan Motor and Blade
• Fan Delay/Defrost Termination Switch
• Digital Control
• Compressor Start Components and Overload Protector
• Water Level Sensor/Probe
• Defrost Timer
• Door Hinges, Locks, and Gaskets
• Thermostat
• Condensate Element
• Thermometer
• Springs/Lowerator
• Gear Motor
Labor Up To 2 Hours To Replace
• Drawer Tracks/Cartridges
• Defrost Element
• Pressure Control
• Heating Element
• Solenoid Valve
• Locate/Repair Leak
Labor Up To3 Hours To Replace
• EPR or CPR Valve
• Condenser or Evaporator Coil
• Expansion Valve
• Cap Tube
Labor Up To 4 Hours To Replace
• Compressor
-- This includes recovery of refrigerant and leak check.
-- $55.00 maximum reimbursement for refrigerant recovery (includes recovery machine, pump, torch, oil, flux, minor fittings, solder,
brazing rod, nitrogen, or similar fees).
Refrigerants
• R22 A maximum of $4.00/lb. or 25¢/oz. will be reimbursed.
• R134A A maximum of $7.00/lb. or 44¢/oz. will be reimbursed.
• R404A A maximum of $16.00/lb. or $1.00/oz. will be reimbursed.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
21
International 18600 and CTP-NB Series Service and Installation Manual
Notes
22
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
International 18600 and CTP-NB Series Service and Installation Manual
Notes
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
23
Covington, TN
Mt. Pleasant, MI
Thank you for choosing Delfield!
Help is a phone call away. Help our team of professional, courteous customer
service reps by having your model number and serial number available at the time
of your call (800) 733-8829.
Model:________________________ S/N: _______________________
Installation Date:________________
For a list of Delfield’s authorized parts depots,
visit our website at www.delfield.com
Register your Delfield warranty
online. Go to www.delfield.com
under the service tab to complete.
980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (989) 773-7981 or (800) 733-8829 • Fax (989) 773-3210 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2013 The Delfield Company. All rights reserved. Printed in the U.S.A.
DM18PTB 10/13
XXXXXXX
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement