ASK Proxima C110 DLP User Guide

ASK Proxima C110 DLP User Guide
™
DLP Projector
USER’S
USER’S
GUIDE
GUIDE
Downloaded from ProjectorsManual.com Manuals
WARNING: This product contains chemicals, including lead, known to the State of California to cause
birth defects or other reproductive harm. Wash hands after handling.
WARNING: This product has a lamp which contains a very small amount of mercury. Dispose of it as
required by local, state, or federal ordinances and regulations. For more information, see www.eiae.org
Downloaded from ProjectorsManual.com Manuals
This entire user’s guide is available on the enclosed CD as an Adobe Acrobat pdf file in the following languages: English, French, German, Italian, Norwegian, Portuguese, Spanish, Russian, Japanese, Korean, Traditional Chinese, Simplified Chinese. Before using this projector, please read these instructions.
Le mode d'emploi complet est disponible sur le CD joint sous forme de fichier pdf d'Adobe Acrobat dans les langues suivantes : anglais, français,
allemand, italien, norvégien, portugais, espagnol, russe, japonais, coréen, chinois traditionnel, chinois simplifié. Avant d'utiliser ce projecteur, veuillez
lire ces instructions.
Die vollständige Benutzeranleitung ist auf der im Lieferumfang enthaltenen CD als Adobe Acrobat PDF-Datei in den folgenden Sprachen verfügbar:
Englisch, Französisch, Deutsch, Italienisch, Norwegisch, Portugiesisch, Spanisch, Russisch, Japanisch, Koreanisch, Traditionelles Chinesisch und
Vereinfachtes Chinesisch. Bitte lesen Sie diese Anweisungen vor der Verwendung des Projektors.
La presente guida è disponibile sul CD allegato, come file Adobe Acrobat pdf, nelle seguenti lingue: inglese, francese, tedesco, italiano, norvegese,
portoghese, spagnolo, russo, giapponese, coreano, cinese tradizionale e cinese semplificato. Prima di usare questo proiettore, leggere le seguenti istruzioni.
Hele denne brukerhåndboken finnes på den vedlagte CD-en som en Adobe Acrobat pdf-fil på følgende språk: Engelsk, fransk, tysk, italiensk, norsk,
portugisisk, spansk, russisk, japansk, koreansk, tradisjonell og forenklet kinesisk. Les diss anvisningene før projektoren tas i bruk.
Este guia do usuário completo está disponível no CD anexo, como um arquivo pdf do Adobe Acrobat nos seguintes idiomas: inglês, francês, alemão, italiano,
norueguês, português, espanhol, russo, japonês, coreano, chinês tradicional, chinês simplificado. Antes de utilizar este projetor, leia estas instruções.
Este manual de uso está disponible en su totalidad en el CD incluido, como archivo pdf de Adobe Acrobat, en los siguientes idiomas: inglés, frances, alemán,
italiano, noruego, português, español, ruso, japonés, coreano, chino tradicional, chino simplificado. Antes de usar el proyector, lea estas instrucciones.
Ⱦɚɧɧɨɟ ɪɭɤɨɜɨɞɫɬɜɨ ɩɨɥɶɡɨɜɚɬɟɥɹ ɜ ɩɨɥɧɨɦ ɨɛɴɟɦɟ ɩɪɟɞɫɬɚɜɥɟɧɨ ɧɚ ɩɪɢɥɚɝɚɟɦɨɦ ɤɨɦɩɚɤɬ-ɞɢɫɤɟ ɜ ɜɢɞɟ pdf-ɮɚɣɥɚ Adobe Acrobat ɧɚ ɫɥɟɞɭɸɳɢɯ
ɹɡɵɤɚɯ: ɚɧɝɥɢɣɫɤɨɦ, ɮɪɚɧɰɭɡɫɤɨɦ, ɧɟɦɟɰɤɨɦ, ɢɬɚɥɶɹɧɫɤɨɦ, ɧɨɪɜɟɠɫɤɨɦ, ɩɨɪɬɭɝɚɥɶɫɤɨɦ, ɢɫɩɚɧɫɤɨɦ, ɪɭɫɫɤɨɦ, ɹɩɨɧɫɤɨɦ, ɤɨɪɟɣɫɤɨɦ,
ɬɪɚɞɢɰɢɨɧɧɨɦ ɢ ɭɩɪɨɳɟɧɧɨɦ ɤɢɬɚɣɫɤɨɦ. ɉɟɪɟɞ ɢɫɩɨɥɶɡɨɜɚɧɢɟɦ ɩɪɨɟɤɬɨɪɚ, ɩɪɨɱɢɬɚɣɬɟ ɞɚɧɧɵɟ ɢɧɫɬɪɭɤɰɢɢ.
ŘųKПП .ŴЕ<R$Ű֞ඤŜūʼnƐ CD Ű Adobe Acrobat ų PDF :P཯༜ŭŜūऄⲟŚƑūʼnƃŞЖᜑų➸⠰ųKПП .Ɨřߓ᰻ʼnŤťŖƃŞЖ␣⠰Е:NX⠰Е.)⠰Е$O⠰Е3PП⠰ЕBP-P⠰Е?X⠰ЕR⠰ЕᎣᒍ⠰Е⺩ઞ⠰Е‱‫ת‬
Ԟઞ⠰Е↭‫ת‬Ԟઞ⠰ЖŘų<R$Ɨ‫؃‬᰻ŞƐ߰ŰЕKПП .Ɨ྿şŏ⠿ƄŔťŚʼnЖ
&'
$GREH$FUREDWSGI
Adobe Acrobat (PDF)
동봉된 CD에는 Adobe Acrobat pdf 파일 형식의 사용 설명서가 영어, 프랑스어, 독일어, 이탈리아어, 노르웨이어, 포르투갈어, 스페인어, 러시아어, 일본어, 한국
Downloaded from ProjectorsManual.com Manuals
어, 중국어(번체 및 간체)로 제공됩니다. 이 프로젝터를 사용하기 전에 다음 지침을 읽으십시오.
Declaration of Conformity
FCC Warning
We declare under our sole responsibility that this projector conform to the following
directives and norms:
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000
February, 2004
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple
Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered
trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or
registered trademarks of Adobe Systems Incorporated.
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This User’s Guide applies to model GEN101.
Agency Approvals
UL, CUL, GOST
Other specific Country Approvals may apply. Please see product certification label.
We reserve the right to alter product offerings and specifications at any time without
notice.
Downloaded from ProjectorsManual.com Manuals
3
If you are experienced in setting up projection systems, use the Quick Setup
card that is included with the projector. For complete details on connecting
and operating the projector, refer to this User’s Guide.
Table of Contents
Introduction
Positioning the projector
Projector and Device Connector Guide
Computer connections
Video connections
Connecting a computer source
Required computer connections
Optional computer connections
Displaying a computer source image
Adjusting the image
Using the projector with Windows 98 for the first time
Connecting a video device
Video device connections
Composite video connection
S-video connection
VGA connection
Displaying video
Adjusting the image
Shutting down the projector
Troubleshooting your setup
Using the remote control
Using the audio
Using the keypad buttons
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
Using the menus
Picture menu
Settings menu
Maintenance
Cleaning the Lens
Replacing the Projection Lamp
Cleaning the Lamp Housing Screens
Using the security lock
Appendix
Projected Image Size
Downloaded
from ProjectorsManual.com
Red LED Behavior
and Projector Errors Manuals
6
8
9
9
9
12
12
12
13
14
15
17
18
18
18
19
20
20
22
22
30
31
32
33
33
34
34
35
36
39
42
42
42
44
44
45
45
45
4
Important Operating Considerations for Safety
•
Place the projector in a horizontal position no greater than 15 degrees
off axis.
•
Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
•
Locate the projector at least 4' (1.2 m) away from any heating or cooling
vents.
•
Use only the power cord provided. A surge-protected power strip is
recommended.
•
Refer to this manual for proper startup and shutdown procedures.
•
In the unlikely event of the lamp rupturing, discard any edible items
placed in the surrounding area and thoroughly clean the area along all
sides of the projector. Wash hands after cleaning the area and handling
the ruptured lamp. This product has a lamp which contains a very
small amount of mercury. Dispose of it as required by local, state or
federal ordinances and regulations. For more information see
www.eiae.org.
.6m)
2 ft (
Do not place objects or people in the 2 foot (.6m) area along the front of the projector.
For ceiling mount applications, this area should be 5 feet (1.5m).
Follow these instructions to help ensure image quality and lamp life over
the life of the projector.
5 ft (1.5m)
Downloaded from ProjectorsManual.com Manuals
5
Introduction
speaker
keypad
Your new digital projector is simple to connect, easy to use, and straightforward to maintain. It is a versatile projector that is flexible enough for business presentations and home video viewing too. It has native SVGA
800x600 resolution and is compatible with a wide variety of computers and
video devices, including:
•
power cord
connector
power switch
Most standard VCRs, DVD players (progressive and interlaced), progressive DVD, HDTV sources, TV and satellite tuners, camcorders,
video games, and laser disc players.
•
IBM-compatible computers, including laptops, up to 1024x768 resolution.
•
Apple® Macintosh® and PowerBook® computers up to 1024x768 resolution.
remote control
receiver (IR)
adjustable foot release
focus (thin ring)
zoom (thick ring)
tethered lens cap
Accessories
The standard accessories that came with your projector can be found on the
included packing list.
lamp
housing
door
security lock
connector
panel
adjustable
foot
Downloaded from ProjectorsManual.com Manuals
6
Connector Panel
The projector provides both computer and video connection options,
including:
•
M1 for computer and video
•
S-video
•
Composite RCA audio/video
RCA
audio/visual
The projector also provides the following connectors:
•
Monitor out
•
Audio out
•
12 volt DC output (see below)
12 volt
DC output
12 volt DC output
+12v
The 3.5mm mini-jack trigger provides a 12 volt DC output. It provides a
constant output while the projector is on. It has numerous uses. For example, if you connect your projection screen to the 12 volt DC output with the
cable that came with your screen, when you turn on the projector the screen
will move down; when you turn the projector off, the screen will return to
the storage position. To use the 12 volt DC output, you must first remove
the safety plug.
M1computer monitor
audio
out
S-video
ground
3.5mm plug
12 volt DC output
to, for example, screen relay (see screen manufacturer
for details)
Downloaded from ProjectorsManual.com Manuals
7
Positioning the projector
12
•
•
ft.
•
f t.
Position the projector within 10 feet (3m) of your power source and
within 6 feet (1.8m) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector
within 6 inches (.15m) of a wall or other object.
4.8 ft.
Projection angle in 4:3 mode (default)
Position the projector the desired distance from the screen. The distance
from the lens of the projector to the screen, the zoom setting, and the
video format determine the size of the projected image. The top illustration to the right shows three projected image sizes. For more information about image sizes at different distances, see “Projected Image
Size” on page 45.
bottom of image
1.22 ft above center
of lens
•
See “Connecting a video device” on page 17 for additional information
on 16:9 and 4:3 modes.
lens center
10 ft high
image
The image exits the projector at a given angle. This image offset is
112.2% when the projector is in 4:3 mode (default mode). This means
that if you have an image 10’ high, the bottom of the image will be 1.22’
above the center of the lens.
This image offset is 132.9% when the projector is in 16:9 mode. This
means that if you have an image 10’ high, the bottom of the image will
be 3.29’ above the center of the lens.
19 ft.
7.5 ft.
10 ft high
image
If you are installing the projector on the ceiling, refer to the installation
guide that comes with the Ceiling Mount Kit for more information. To
turn the image upside down, see “Ceiling” on page 39. We recommend
using an authorized ceiling mount.
•
ft.
•
5
Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 4.9 feet (1.49m) from the projection screen.
3
3.
•
.5
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between
the projector and the rest of your equipment. Here are some general guidelines:
Projection angle in 16:9 mode
bottom of image
3.29 ft above center
of lens
Downloaded from ProjectorsManual.com Manuals
8
lens center
Projector and Device Connector Guide
The following illustration and table should help you find the connectors to use and obtain the best resolution possible from your input devices, such as computers, standard VCRs, DVD players (progressive and interlaced), HDTV sources, TV and satellite tuners, camcorders, video games (progressive and interlaced), and laser disc players.
Computer connections
Computer connections involve attaching the VGA and USB ends of the provided computer cable to a computer and connecting the other end (M1) to the
Computer In input on the projector. The USB part of the computer cable allows you to advance slides in a PowerPoint™ presentation via a remote control.
See page 12 for computer/projector setup information.
Video connections
The first step for connecting video is deciding what type of output connector you want to connect to the projector. If there is more than one output on your
video device, select the one with the highest quality. Your options are S-video (higher quality) and Composite video (lesser quality).
If you are connecting the projector to HDTV sources, the projector’s M1 computer connector, labeled Computer In, should be used. Keep in mind that
HDTV and progressive sources should only be handled through the projector’s computer connector. You can also use an M1 to Component adapter (available as an optional accessory) to connect a progressive source’s component connectors to the projector. The S-video port does not function with progressive
sources.
audio/visual
(composite)
projector input connectors
12 volt
DC output
computer in
monitor
S-video
(HDTV and
(out)
audio out
progressive
sources)
Downloaded from ProjectorsManual.com Manuals
9
Video Device
Standard Broadcast TV (not
HDTV) via: cable, digital
cable, satellite TV, DVD, or
VCR
Standard Video Camera
Video
Compatibility
If Your Device
Connector Is
Attach to Adapter
or Labeled
Connector on
Projector
For Setup Instructions, see
Comments
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Composite video
or S-video
Composite video connection on
page 18.
Not for progressive
(i.e. HDTV) sources.
See page 11.
S-video connection on page 18
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Composite video
or S-video
Composite video connection on
page 18.
Not for progressive
(i.e. HDTV) sources.
See page 11.
S-video connection on page 18
Standard Video Game
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Composite video
or S-video
Composite video connection on
page 18.
S-video connection on page 18
Downloaded from ProjectorsManual.com Manuals
10
Not for progressive
(i.e. HDTV) sources.
See page 11.
Video Device
Video
Compatibility
If Your Device
Connector Is
Attach to Adapter
or Labeled
Connector on
Projector
For Setup Instructions, see
Comments
1080i, 720p
VGA
Computer In
VGA connection on page 19
Not for Component
480i.
Component video
Computer In via
optional M1 to Component adapter
M1 to Component adapter on
page 19
1080i, 720p
VGA
Computer In
VGA connection on page 19
Component 480p
Component video
Computer In via
optional M1 to Component adapter
M1 to Component adapter on
page 19
1080i, 720p
VGA
Computer In
VGA connection on page 19
Component 480p
Component video
Computer In via
optional M1 to Component adapter
M1 to Component adapter on
page 19
HDTV
(High Definition TV)
Progressive DVD
Progressive Video Game
Downloaded from ProjectorsManual.com Manuals
11
Not for Component
480i.
Not for Component
480i.
Connecting a computer source
Required computer connections
connect computer cable
Connect one end of the provided computer cable (see page 17 for connecting video devices) to the blue M1 Computer In connector on the projector.
Connect the other ends (USB and VESA) to the USB and VGA ports on your
computer. If you are using a desktop computer, you will need to disconnect
the monitor cable from the computer’s video port first.
This connection allows you to advance slides in a PowerPoint presentation
using the remote. USB drivers must be installed to use the USB feature.
For more information, see page 16.
connect power cable
Connect the black power cord to the Power connector on the side of the projector and to your electrical outlet.
NOTE: Always use the power cord that shipped with the projector.
Optional computer connections
connect audio cable
To have sound with your presentation, connect an audio cable (not
included) to your computer and to the red and/or white Audio In connectors on the projector.
connect monitor cable
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, connect the computer’s
monitor cable to the Monitor Out connector on the projector.
Downloaded from ProjectorsManual.com Manuals
12
Displaying a computer source image
remove lens cap
Remove the lens cap.
Toggle the Power switch on the side of the projector to the On position.
toggle Power switch
The LED flashes green and the fans start to run. When the lamp comes on,
the start up screen displays and the LED is steady green. It can take a
minute for the image to achieve full brightness.
? No start up screen? Get help on page 22.
Turn on your computer.
turn on computer
The computer’s image should appear on the projection screen. If it doesn’t,
press the Computer button on the projector’s keypad.
If your computer has Windows 98 as its operating system, see “Using the
projector with Windows 98 for the first time” on page 15 regarding the
driver setup process.
Make sure your laptop’s external video port is active.
activate laptop’s external port
monitor key
or LCD/CRT key
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/LCD
key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the
labeled function key simultaneously. Refer to your laptop’s documentation to learn your laptop’s key combination.
FN key
? No laptop image? Try pressing the Auto Image button on the keypad. Get help on page 23.
Downloaded from ProjectorsManual.com Manuals
13
Adjusting the image
adjust height
If necessary, adjust the height of the projector by pressing the release button
to extend the foot.
rotate
leveling
foot
If necessary, rotate the leveling foot located at the rear of the projector.
elevator
foot
Avoid placing your hands near the hot exhaust vent in front of the projector.
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
release button
adjust distance
See page 45 for a table listing screen sizes and distances.
Adjust the zoom or focus.
adjust zoom or focus
focus
(thin ring)
If the image is not square, adjust the keystone using the buttons on the keypad.
adjust keystone
Press the top Keystone button to reduce the upper part of the image, and
press the bottom Keystone button to reduce the lower part.
Adjust the Contrast or Brightness in the Picture menu.
adjust Picture menu
See page 36 for help with these menu adjustments.
Downloaded from ProjectorsManual.com Manuals
14
zoom
(thick ring)
Using the projector with Windows 98 for the first
time
a
The first time you connect a computer running Windows 98 to the projector,
the computer recognizes the projector as “new hardware” and the Add
New Hardware Wizard appears. Follow these instructions to use the Wizard to load the correct driver (which was installed with your Windows
operating system).
If you are running Windows 2000 or Windows ME, skip these steps and go
to “Adjusting the image” on page 14.
b
a Click Next to begin searching for the driver.
b Make sure “Search for the best driver” is selected, then click Next.
c
c Uncheck any checked boxes, then click Next. Windows automatically
locates the driver. If this driver has been removed, reload the driver using
your Windows operating system CD.
d
d When Windows finds the driver, you are ready to install it. Click Next.
Downloaded from ProjectorsManual.com Manuals
15
Skip this page if you did not connect a USB mouse cable
For Windows 98:
•
If you connected the USB cable, the Add New Hardware Wizard
appears again. Drivers must be installed to use the USB functionality.
•
The Wizard launches three times.
The first time it detects a USB Composite Device.
The second time a USB Human Interface Device (for the keyboard).
The third time it detects a USB Human Interface Device (for the
mouse).
For Windows 2000, Windows ME, and Windows XP:
•
The USB drivers are automatically installed.
Downloaded from ProjectorsManual.com Manuals
16
Connecting a video device
4:3 screen
You can connect video devices such as VCRs, DVD players, camcorders,
digital cameras, video game consoles, HDTV receivers, and TV tuners to the
projector. There is also an audio input via the red and white A/V connectors. You can connect the audio directly to the projector to get sound from
the built-in speaker, or you can connect the audio to your stereo system via
the Audio Out connector.
16:9 screen
Do Not Use
4:3
mode
You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a
cable or satellite company, the signal must pass through a tuner first. Examples of tuners are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can change channels is considered
a tuner.
Before connecting your projector, you should decide which aspect ratio you
want to use. The projector’s Aspect Ratio setting is accessed through the
projector’s Picture Menu. See page 36 for more information.
16:9
mode
What is Aspect Ratio?
Aspect ratio is the ratio of the image width to image height. TV screens are
usually 4:3, which is the default for this projector. HDTV and most DVDs
are 16:9. If you’re projecting onto a screen, the size/shape of the screen may
determine which aspect ratio to use. If you are projecting onto a blank wall,
you don’t have the screen size restriction. What you plan to project will also
help you choose between 4:3 and 16:9. Most TV shows are 4:3, while most
movies are 16:9.
Native
mode
(NTSC
only)
If a have a 16:9 screen then you should select an aspect ratio of 16:9 for
anamorphic movies or HDTV, and Native for 4:3 content. If you have a 4:3
screen you should still use 16:9 for anamorphic movies or HDTV, but you
also have the option of using either 4:3 (to fill the screen) or Native (for
direct pixel mapping) for 4:3 content. Keep in mind that anamorphic movies
only appear correctly if the DVD player is set to output to a 16:9 television.
Downloaded from ProjectorsManual.com Manuals
17
Video device connections
Composite video connection
Plug the provided A/V cable’s yellow connector into the video-out connector on the video device. Plug the other yellow connector into the yellow
Video 2 connector on the projector.
connect A/V cable
Plug a white connector into the left audio out connector on the video device
and plug a red connector into the right audio out connector on the video
device. Plug the remaining white connector into the white audio in connector on the projector, and plug the remaining red connector into the red
audio in connector on the projector.
Keep in mind that video output from composite connections are not as high
quality as S-video.
S-video connection
If your video device uses a round, seven-prong S-video connector, plug an
S-video cable (available as an optional accessory) into the S-video connector
on your video device and into the S-video connector on the projector. Use
the A/V cable’s red and white audio connectors as described directly above
(the yellow connectors on the A/V cable are not used).
Keep in mind that S-video delivers higher quality video output than composite.
connect S-video and A/V cables
Downloaded from ProjectorsManual.com Manuals
18
VGA connection
If your video device has a 15-pin VGA output, plug one end of the included
computer cable into the VGA connector on your video source. This connector may be labeled “To Monitor” on the video source. Plug the M1 computer
end of the cable into the Computer In connector on the projector. Do not
plug the USB end of this cable into the video device.
connect computer and
A/V cables
Use the A/V cable’s red and white audio connectors as described on the
previous page (the yellow connectors on the A/V cable are not used).
M1 to Component adapter
To connect a progressive scan DVD or HD source, use an M1 to Component
adapter (available as an optional accessory). Connect one end of a component cable (not provided) into the adapter. Connect the M1 end of the
adapter into the Computer 1 connector on the projector.
connect power cable
Connect the power cord to the Power connector on the side of the projector
and to your electrical outlet.
NOTE: Always use the power cord that shipped with the projector.
Downloaded from ProjectorsManual.com Manuals
19
Displaying video
remove lens cap
Remove the lens cap.
Toggle the Power switch on the side of the projector to the On position.
toggle Power switch
The LED flashes green and the fans start to run. When the lamp comes on,
the start-up screen is displayed and the LED is steady green. It can take a
minute for the image to achieve full brightness.
? No start up screen? Get help on page 23.
Plug in and turn on your video device.
turn on video device
The video device’s image should appear on the projection screen. If it
doesn’t, press the Video button on the keypad.
? No image? Try pressing the Source or Auto Image Get help on
page 23.
Adjusting the image
adjust height
rotate
leveling
foot
Adjust the height of the projector by pressing the release button to extend
the foot.
Rotate the leveling foot at the rear of the projector, if necessary.
elevator
foot
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
adjust distance
See page 45 for a table listing screen sizes and distances to the screen.
Downloaded from ProjectorsManual.com Manuals
20
release button
Adjust the zoom and focus.
adjust zoom and focus
focus
(thin ring)
If the image is not square, adjust the keystone using the buttons on the keypad. Press the top Keystone button to reduce the upper part of the image,
and press the bottom Keystone button to reduce the lower part.
adjust keystone
adjust volume
Adjust the volume on the keypad or remote.
Adjust the Contrast, Brightness, Color, Tint, or Aspect Ratio in the Picture
menu. See page 36 for help with the menus and these adjustments.
adjust Picture menu options
including Aspect Ratio
For Aspect Ratio, keep in mind that DVD players must be configured for
16:9 in order to view the highest quality image. For more information
regarding Aspect Ratio, see page 17.
Downloaded from ProjectorsManual.com Manuals
21
zoom
(thick ring)
Shutting down the projector
Troubleshooting your setup
The projector automatically displays a black screen after no active source is
detected for 30 minutes. This black screen helps preserve the life of the projector. The image returns when an active source is detected or a remote or
keypad button is pressed.
If your image appears correctly on the screen, skip to the next section. If it
does not, troubleshoot the setup.
The LED on top of the projector indicates the state of the projector and can
help you troubleshoot.
Screen Save
Table 1: LED behavior and meaning
You can make the black screen appear after a preset number of minutes by
turning on the Screen Save feature in the Settings>System menu. See
page 39.
Power Save
The projector also has a Power Save feature that automatically turns the
lamp off after no active sources are detected and no user interaction with
the projector is performed for 20 minutes. By default, this feature is off. See
page 39.
LED color/behavior
Meaning
solid green
The power switch has been toggled on
and the software has initialized or the projector has been powered off via the
remote.
blinking green
The power switch has been toggled on
and the software is initializing, or the projector is powering down and the fans are
running to cool the lamp.
blinking red
A fan or lamp failure has occurred. Make
sure the vents aren’t blocked (see
page 28). Turn off the projector and wait
one minute, then turn the projector on
again. If the projector has been working
exceeded its lamp life (page 42), replace
the lamp and reset the lamp timer. Contact your dealer if the problem persists.
Turning off the projector
You can turn the projector off simply by toggling the power switch to the off
position.
You can also press the remote’s Power button to place the projector in the
Off state while it is running. When the Power button is pressed twice (once
to start the power-down process and a second time to verify that you want
to power the projector off), the lamp turns off and the LED blinks green for
one (1) minute while the fans continue to run to cool the lamp. While the
LED is blinking green, the projector does not accept any keypad and remote
control input.
see page 45 for more information
solid red
When the lamp has cooled, the LED lights solid green and the fans slow
down to minimal speed. To turn off the projector, toggle the power switch to
the off position.
An unidentifiable error: please contact
your dealer
The following tables show common problems. In some cases, more than one
possible solution is provided. Try the solutions in the order they are presented. When the problem is solved, you can skip the additional solutions.
NOTE: Once the projector has been toggled off, you must wait for one (1)
minute before turning the projector on again. This allows the lamp to properly cool. However, if the remote was used to power the projector to the Off
state you do not need to wait one minute to turn it on again.
Downloaded from ProjectorsManual.com Manuals
22
Problem
Solution
Result
no start up screen
plug power cord in projector’s left side
remove lens cap
toggle power switch
correct image
toggle power switch
on side
press the Computer button
activate laptop’s external port
only start up screen appears
A
Startu
p
Scree
n
Start
u
Scre p
en
computer image projected
A
restart laptop
Downloaded from ProjectorsManual.com Manuals
23
A
Problem
Solution
Result
no computer image, just the words “Signal out of
range”
press the Auto Image button on keypad
computer image projected
A
Signa
l
rang out of
e
adjust computer refresh rate in Control
Panel>Display>Settings>Advanced>Adapter
(location varies by operating system)
you may also need to set a different
resolution on your computer, as shown
in the following problem, “image fuzzy
or cropped”
Downloaded from ProjectorsManual.com Manuals
24
A
A
Problem
Solution
Result
image fuzzy or cropped
set your computer’s display resolution to
the native resolution of the projector
(Start>Settings>Control
Panel>Display>Settings tab)
select 800x600
image clear and not cropped
AA
A
A
For a laptop,
disable laptop
monitor
or turn-on dualdisplay mode
move projector, adjust zoom, adjust height
image not centered on screen
correct image
adjust horizontal or
vertical position in
Picture>Advanced
menu
Downloaded from ProjectorsManual.com Manuals
25
Problem
Solution
Result
image not square
adjust Keystone on keypad
square image
image not sharp
adjust Sharpness (video sources only) in the
Picture>Advanced menu
correct image
AB
AB
image does not fit 4:3 or 16:9 screen
change aspect ratio to 4:3 or 16:9 in
Picture>Aspect ratio menu
Downloaded from ProjectorsManual.com Manuals
26
correct image
Problem
Solution
Result
image upside down
turn off ceiling in Settings>System menu
correct image
AB
image reversed left to right
AB
turn off rear in Settings>System menu
correct image
A
projected colors don’t match source
AB
adjust color, tint, color temperature,
brightness, contrast in the menus
COLOR
correct image
COLOR
Downloaded from ProjectorsManual.com Manuals
27
Problem
Solution
Result
The video embedded in my PowerPoint
presentation does not play on the screen
Turn off the internal LCD display on your
laptop
Embedded video plays correctly
A
B
A
A
B
lamp won’t turn on, LED blinking red
make sure vents aren’t blocked, turn off the
projector and allow it to cool for one
minute
LED
lamp turns on
Start
u
Scre p
en
Downloaded from ProjectorsManual.com Manuals
28
B
Problem
Solution
Result
“Change lamp” message appears at startup or lamp
won’t turn on and LED blinking red
lamp must be replaced (see page 42)
lamp turns on
Start
u
Scre p
en
LED
replace lamp
Downloaded from ProjectorsManual.com Manuals
29
Using the remote control
previous button
next button
The remote uses two (2) provided AA batteries. They are easily installed by
sliding the cover off the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover.
Caution: When replacing the batteries, be aware that using batteries other
than the type provided with the projector may risk severe damage to the
remote. When disposing of the batteries, be sure to do so in an environmentally proper manner.
navigation
buttons
To operate, point the remote at the projection screen or at the projector (not
at the computer). The range of optimum operation is about 15 feet (4.5m).
Pressing the remote’s Power button when the projector’s Power toggle
switch is in the Off position does not cause the projector to power up. You
need to put the projector’s Power toggle switch in the On position to let the
remote power on the projector.
Troubleshooting the remote
•
When the projector is running, you can press the remote’s Power button to
place the projector in the Off state (see page 22 for shutdown info) and
power it off.
Make sure the batteries are installed in the proper orientation and are
not dead.
•
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 35 for more info on the menus.
Make sure you’re pointing the remote at the projector or the screen, not
the computer, and are within the remote range of 15 feet (4.5m). For
best results, point the remote at the screen.
•
If you are trying to advance PowerPoint slides, make sure the USB
cable is connected. If using a USB cable, make sure the correct drivers
are installed.
The remote also has Volume and Mute buttons to control the sound, and
Video and Computer buttons to switch between sources.
Two presentation-specific features are also provided. Use the Blank button
to display a blank screen instead of the current slide (you can choose which
color is displayed, see page 40); use the Effect button to invoke a user-definable action, such as freeze, or change your aspect ratio for viewing DVDs
(see page 40 to learn to program this button).
Previous and Next buttons allow you to navigate through your PowerPoint
presentation while in Slide Show mode. Connect the USB connector on the
provided computer cable to your computer to use these buttons. When you
do this for the first time, the Add New Hardware wizard may appear. See
ProjectorsManual.com
Manuals
pageDownloaded
16 for detailsfrom
on loading
the correct USB drivers.
30
Using the audio
connect audio cable
Using the projector’s speakers
To use the projector’s speaker, connect your source to the Audio In connectors (L and/or R) on the projector’s composite connectors.
To adjust the volume, press the Volume buttons on the keypad or remote.
To mute the sound, press the Mute button on the remote.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
•
Make sure the audio cable is connected.
•
Make sure mute is not active (press the Mute button on the remote).
•
Make sure the volume is turned up enough. Press the Volume button
on the keypad or remote.
•
Make sure the correct source is active.
•
Adjust the audio source.
•
If playing a video, make sure the playback has not been paused.
adjust volume
Connecting external speakers
The projector can be attached to external speakers that have their own
power source by plugging a speaker cable (not included) into the projector’s
Audio Out connector.
external speakers
with own power source
audio out
speaker
cable
Downloaded from ProjectorsManual.com Manuals
31
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of their functions:
Menu–opens the on-screen menus (page 35).
menu navigation
buttons
Select–confirms choices made in the menus (page 35).
Up/Down arrows–navigates to and adjusts settings in the menus (page 35).
Auto Image–resets the projector to the source.
Presets–cycles through the available preset settings (page 37).
Keystone–adjusts squareness of the image (page 14).
Volume–adjusts sound (page 31).
Video and Computer–changes the active source.
Downloaded from ProjectorsManual.com Manuals
32
Optimizing computer images
Presentation features
After your computer is connected properly and the computer’s image is on
the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 35.
Several features are provided to make giving presentations easier. Here is an
overview, details are found in the menu section.
•
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced menu (page 38).
The Effect button on the remote allows you to assign various features to
the button. The default effect is About, which displays information
about the projector and current source. You can select among Blank,
Mute, Aspect Ratio, Source, Auto Image, Freeze, and About. See
page 40 for details. The freeze effect allows you to freeze the displayed
image. This is useful if you want to make changes on your computer
without your audience seeing them. The mask effect allows you to
cover part of the image with a black curtain.
•
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
settings later (page 37).
The Blank button on the remote allows you to display a blank screen
instead of the active source. You can determine the color of this screen
(page 40).
•
The Startup Logo option lets you change the default start up screen to a
blank or default screen (page 40).
•
Two options, Power Save and Screen Save, are provided to automatically shut down the projector after several minutes of inactivity or display a black screen. This helps preserve lamp life (page 39).
•
Adjust the Keystone, Contrast, or Brightness in the Picture menu
(page 36).
•
Change the Aspect Ratio. Choose the option that best fits your input
source (page 36).
•
Adjust the Color Temperature in the Advanced menu (page 38).
•
•
Downloaded from ProjectorsManual.com Manuals
33
Optimizing video images
Customizing the projector
After your video device is connected properly and the image is on the
screen, you can optimize the image using the onscreen menus. For general
information on using the menus, see page 35.
You can customize the projector for your specific setup and needs. See
page 39 to page 41 for details on these features.
•
For rear projection, turn rear mode on in the Settings>System menu.
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
menu (page 36).
•
For ceiling mounted projection, turn ceiling mode on in the Settings>System menu.
•
Change the Aspect Ratio. Choose the option that best fits your input
source (page 36).
•
Specify which source the projector checks first for active video during
power-up.
•
The remote’s Effect button allows you to assign various features to the
button. The default effect is About, which displays information about
the projector and current source. You can select among Blank, Mute,
Aspect Ratio, Source, Auto Image, Freeze, and About. See page 40 for
details.
•
Specify the function of the Effect button on the remote.
•
Turn the projector’s display messages on and off.
•
Turn on power saving features.
•
Specify blank screen colors and start up logos.
•
Select a Sharpness setting (page 38).
•
Specify the language viewed on the menus.
•
Use the Color Control to adjust the color gain (page 38).
•
Save settings for the active source as a preset.
•
Adjust the Color Temperature. Select a listed warmth value (page 38).
•
Turn on Overscan to remove noise on the edges of the image.
Downloaded from ProjectorsManual.com Manuals
34
Using the menus
keypad navigation
buttons
Main menu
To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to highlight the desired submenu, then press the Select button.
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio buttons, or turn the feature on or off using check boxes. Press Select to confirm
your changes. Use the arrows to navigate to another setting. When your
adjustments are complete, navigate to Previous or Exit, then press Select to
go to the previous menu; press the Menu button at any time to close the
menus.
Settings
menu
Picture
menu
Dots appears before the menu name. The number of dots indicate menu’s
level, ranging from one (the Main menu) to four (the most nested menus).
dots
The menus are grouped by usage:
•
The Picture menu provides image adjustments.
•
The Settings menu provides set-up type adjustments that are not
changed often.
•
The About menu provides a read-only display of information about the
projector and source.
Certain menu items may not be visible or may be grayed depending upon a
particular source being connected. For example, Sharpness is only available
for video sources and is not visible when a computer source is active. Menu
options are grayed out only if the source if selected but no signal is present.
For example, if the projector is set to a video source but the source, such as a
DVD player, is turned off video menu options are grayed out.
About menu
Downloaded from ProjectorsManual.com Manuals
35
Picture menu
Picture menu
To adjust the following settings, highlight the setting, press Select, use the
up and down arrows to adjust the values, then press Select to confirm the
changes.
Keystone: adjusts the image vertically and makes a squarer image. You can
also adjust keystone from the keypad.
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
increasing keystone
decreasing keystone
Brightness: changes the intensity of the image.
Color: adjusts a video image from black and white to fully saturated color.
The color setting applies to video sources only.
Tint: adjusts the red-green color balance in the image of NTSC video
images. The tint setting applies to NTSC video sources only.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
TV screens are usually 4:3. HDTV and most DVDs are 16:9. The default is
4:3.
Select Native to see the unmodified input with no resizing by the projector.
Select 16:9 to watch enhanced widescreen DVDs.
For more information regarding Aspect Ratio, see page 17.
Aspect ratio
Downloaded from ProjectorsManual.com Manuals
36
Presets: Presets are provided that optimize the projector for displaying
computer presentations, photographs, film images, and video images. Film
input is material originally captured on a film camera, like a movie; video
input is material originally captured on a video camera, like a TV show or
sporting event. You can use the preset as a starting point, then further customize the settings for each source. The settings you customize are saved in
the preset for each source. To restore the factory default settings, choose Factory Reset in the Settings>Service menu (page 41).
Presets
Save
User
Settings
There is also a user-definable preset. To set a preset for the current source,
adjust the image, select Save User in the Presets menu, then select Yes. You
can recall these settings in the future by selecting the User 1 preset.
Downloaded from ProjectorsManual.com Manuals
37
Advanced menu
Sharpness: (video sources only) changes the clarity of the edges of a video
image. Select a sharpness setting.
Advanced menu
Color Space: This option applies to computer and component video
sources. It allows you to select a color space that has been specifically tuned
for the input signal. When Auto is selected, the projector automatically
determines the standard. To choose a different setting, turn off Auto, then
choose RGB for computer sources, choose either SMPTE240, REC709 or
REC601 for component video sources.
Sharpness
Color Temperature: changes the intensity of the colors. Select a listed relative warmth value.
Color
Space
Color
Temperature
Color Control: allows you to individually adjust the gain (relative warmth
of the color) and the offset (the amount of black in the color) of the red,
green, and blue colors.
Video Standard: when it is set to Auto, the projector attempts to automatically pick the video standard based on the input signal it receives. (The
video standard options may vary depending on your region of the world.) If
the projector is unable to detect the correct standard, the colors may not
look right or the image may appear “torn.” If this happens, manually select
a video standard by selecting NTSC, PAL, or SECAM from the Video Standard menu.
Overscan: (video sources only) removes noise around the video image.
Color Control
Sync Threshold Adjust: If a hardware device, such as a DVD player, is not
syncing properly with the projector, select this option to help it to sync
when connected to the projector.
The following four (4) options are for computer sources only.
Phase: adjusts the horizontal phase of a computer source.
Tracking: adjusts the vertical scan of a computer source.
Video Standard
Horizontal/Vertical Position: adjusts the position of a computer source.
White Peaking: increases the brightness of whites that are near 100%.
Downloaded from ProjectorsManual.com Manuals
38
Settings menu
Settings menu
Audio: allows adjustments to Volume of the internal speaker and allows a
chime to play when starting the projector. Adjustments can also be made
from the projector’s keypad and the remote.
Audio
Sources: Power-up Source determines which source the projector checks
first for active video during power-up. When the Autosource feature is On,
the projector automatically finds the active source, checking the selected
Power-up Source first. The source options are Computer 1 for a computer,
progressive DVD, or HDTV source, and Video 1 (for S-video connections),
and Video 2 (for composite video connections) for video sources. When this
feature is Off, the projector defaults to the source selected in Power-up
Source. To display another source, you must manually select one by pressing the Computer or Video button on the remote or keypad.
Sources
Power-up
Source
System>Rear: reverses the image so you can project from behind a translucent screen. Ceiling: turns the image upside down for ceiling-mounted projection. Low Power: toggles between on and off. Turn it on to lower the light
output of the lamp. This also lowers the fan speed, making the projector
quieter. Display Messages: displays status messages (such as “Searching” or
“Mute”) in the lower-left corner of the screen. Screen Saver Off: prevents
your computer from going into Screen Save mode. Power Save: automatically turns the lamp off after no signals are detected for 20 minutes. After 10
additional minutes with no signal, the projector powers down. If an active
signal is received before the projector powers down, the image will be displayed. After an additional 10 minutes with no signal, the projector powers
down and can be toggled off. If an active signal is received before the projector powers down, the image will be displayed. When Power Save is
enabled, Screen Save is disabled. Screen Trigger controls the 12 volt DC
output switch on the connector panel. Screen Save automatically blanks
the screen with a black color after no signals are detected for a preset number of minutes. The image returns when an active source is detected or a
remote or keypad button is pressed.
System menu
Screen Save
Downloaded from ProjectorsManual.com Manuals
39
Startup Logo: allows you to display a blank screen instead of the default
screen at startup, and when no source is detected.
Startup Logo
Blank Screen: determines what color is displayed when you press the
Blank button on the remote.
Blank Screen
Effect Key: allows you to assign a different function to the Effect button on
the remote, allowing you to quickly and easily use the effect. Highlight an
effect and press Select to choose a different one.
•
Blank: displays an empty screen.
•
Mute: turns off all sound.
•
Aspect Ratio: toggles among 4:3, 16:9, and Native (see page 17 and
page 36). Set as the Effect Key, it can allow you to switch the Aspect
Ratio for DVDs.
•
Source: cycles through available sources.
•
Auto Image: resets the projector to the source (page 32).
•
Freeze: pauses the projected image.
•
About: the default effect. It opens a window with projector and source
information.
Effect Key
Downloaded from ProjectorsManual.com Manuals
40
Language: allows you to select a language for the onscreen display.
Language menu
Service: To use these features, highlight them and press Select.
Service menu
Factory Reset: restores all settings to their default.
Lamp Reset: resets the lamp hours used counter in the About menu to
zero. Do this only after changing the lamp.
Service Code: only used by authorized service personnel.
About: provides information about the projector and the active source.
Showing the About box is the default action assigned to the Effect button.
About menu
Downloaded from ProjectorsManual.com Manuals
41
Maintenance
Cleaning the Lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you
don’t intend to use the projector immediately, replace the lens cap.
Replacing the Projection Lamp
The lamp hours used timer in the About menu counts the number of hours
the lamp has been in use. Twenty hours before the lamp life expires, the
message “Change lamp” appears on the screen at startup. If the maximum
lamp time is exceeded, the lamp will not light. In this case, after replacing
the lamp you must reset the lamp hours by simultaneously pressing both
Volume buttons on the keypad and holding them for 10 seconds.
Lamp hours used
turn off and unplug
projector
wait 30 minutes
NOTE: You can order new lamp housings from your dealer. See the Packing
list for information. Use only a replacement lamp with the same type and
rating as the original lamp.
1 Turn off the projector and unplug the power cord.
2 Wait 30 minutes to allow the projector to cool thoroughly.
3 Turn the projector on its side so that the lamp door is facing you. Using a
flat-blade screwdriver, gently pry the lamp door from the projector by
placing the screwdriver blade into the space between the top of the lamp
door and the projector.
lamp door
Downloaded from ProjectorsManual.com Manuals
42
4 Loosen the two captive screws that attach the lamp housing to the projector.
lamp
connector
5 Detach the lamp connector from the projector by depressing the locking
lamp cable
tab on the connector and lightly pulling it free.
WARNING:
To avoid burns, allow the projector to cool for at least 30 minutes
before you replace the lamp.
Do not drop the lamp housing or touch the glass bulb! The glass
may shatter and cause injury.
lamp
housing
Be extremely careful when removing the lamp housing. In the
unlikely event that the bulb ruptures, small glass fragments may be
generated. The lamp housing is designed to contain these fragments, but use caution when removing the lamp housing. Before
replacing the lamp, clean the lamp compartment and dispose of
cleaning materials. Wash hands after lamp replacement. This product has a lamp which contains a very small amount of mercury. Dispose of it as required by local, state or federal ordinances and
regulations. For more information see www.eiae.org.
captive screw
connector
6 Carefully remove the lamp housing. Dispose of the lamp in an environ-
lamp cable
locking tab
mentally proper manner.
7 Install the new lamp housing and tighten the screws.
lamp
housing
8 Re-attach the lamp connector to the projector. The locking tab should
captive screw
engage when the connector is fully plugged in.
9 Replace the lamp door.
10 Plug in the power cord and toggle the Power switch to turn the projector
back on.
11 To reset the lamp hour timer, navigate to the Settings>Service menu
Service menu
and select Lamp Reset. See page 41 for details.
Downloaded from ProjectorsManual.com Manuals
43
Cleaning the Lamp Housing Screens
In dirty or dusty environments, the two dust filter screens in the lamp housing can become clogged, causing high temperatures and premature lamp
failure. Routine maintenance to remove dust from the screens lowers the
lamp operating temperature and prolongs lamp life. To maximize lamp life
you should clean the screen every 250 hours.
lamp housing
lamp
1 Remove the lamp housing.
two screens
(one on each
side of the
lamp housing)
2 Examine the dust filter screens on the lamp housing. If necessary, use a
vacuum cleaner set on low power to clean the screens. Be careful not to
disturb any internal components when cleaning the screens.
3 Replace the lamp housing and lamp door.
Using the security lock
The projector has a security lock for use with a cable lock system. Refer to
the information that came with the lock for instructions on how to use it.
security
lock
Downloaded from ProjectorsManual.com Manuals
44
Appendix
Red LED Behavior and Projector Errors
Projected Image Size
If the projector is not functioning properly and the LED is blinking red, consult Table 3 to determine a possible cause. There are two-second pauses
between the blinking cycles.
Table 3:
Table 2:
Range of distance to the screen for a given screen size for the projector
Red LED Behavior
Explanation
One (1) blink
The lamp won't strike after five (5)
attempts. Check the lamp and lamp door
installations for loose connections.
Two (2) blinks
The lamp counter hours have exceeded
lamp life hours. Replace the lamp and
reset the lamp hours counter.
Three (3) blinks
The projector has shut down. Check to
see if the lamp door is open. If the lamp
door is closed, toggle off the projector
and wait one minute, then toggle the projector on again. If the lamp does not strike
after one minute, replace the lamp. Contact your dealer (see page 30) for repair if
replacing the lamp does not solve the
problem.
Four (4) blinks
The fan has failed. Contact your dealer
(see page 30) for repair or replacing the
fan.
Five (5) blinks
The projector is overheating. Check for a
blocked air vent. Contact your dealer (see
page 30) for repair if clearing the air vents
does not solve the problem.
Distance to screen
Diagonal
Screen Size
(inches/m)
40/1
50/1.3
60/1.5
100/2.5
150/3.8
200/5.1
Image Width
(inches/m)
32/0.8
40/1
48/1.2
80/2
120/3.1
160/4.1
Maximum
distance
(feet/m)
5.8/1.8
7.8/2.4
8.8/2.7
14.6/4.5
22.6/6.9
30.5/9.3
Minimum
Distance
(feet/m)
4.8/1.5
6,5/2.0
7.5/2.3
12.4/3.8
19.03/5.8
25.2/7.7
Downloaded from ProjectorsManual.com Manuals
45
16x9 vs 4x3 screen aspect 17
800x600 resolution 6
connectors on projector 10, 11
Contrast 36
customizing the projector 34
A
D
About 40, 41
Accessories 6
Advance menu 38
advancing slides 12
Aspect Ratio 40
Aspect ratio 36
aspect ratio 17
Audio 39
Audio In connector 12, 18, 31
audio input 17
Audio Out 17
Autosource 39
Display Messages 39
Drivers
USB 16
Windows 98 16
DVDs 36
B
HDTV 6, 9, 36
Horizontal 38
Numerics
E
Effect button 33, 34
Effect Key 40
F
Factory Reset 41
focus 14, 21
H
Blank button 33
Blank Screen 40
blinking green 22
blinking red 22
Brightness 36
I
IBM-compatible computers 6
image
size 8
image optimization 33
image size
projected 45
C
cable box 17
Color 36
Color Control 38
Color Space 38
Color Temperature 38
compatibility
IBM-compatible 6
Macintosh 6
video devices 6
Computer In connector 12
connecting
video device 17
connector
panel 7from ProjectorsManual.com Manuals
Downloaded
K
keypad buttons
projector 32
keystone adjustment 14, 21
L
Lamp Housing Screens
cleaning 44
lamp replacement 42
Lamp Reset 41
Language 41
LED 22
46
blinking green 22
solid green 22
LED Behavior
red 45
LED behavior 22
leveling foot 20
Low Power 39
keypad buttons 32
maintenance 42
positioning 8
setting up 8
troubleshooting problems 22
turning off 22
R
M
M1 to Component adapter 19
Macintosh computers
compatibility 6
maintaining the projector 42
Menu button 35
menu usage 35
Monitor Out connector 12
Mute button 31
Rear 39
Red LED behavior 45
remote control
advancing slides 12, 30
Effect key 30
laser pointer 30
Previous/Next buttons 30
usage 30
replacing the lamp 42
O
S
optimizing images 33
optimizing video 34
Overscan 38
Screen Aspect 17
Screen Save 22, 39
Screen Saver Off 39
Screen Trigger 39
security lock 44
Service 41
Service Code 41
Settings menu 39
sharpness 38
solid green 22
solid red 22
Sources 39
standard accessories 6
Startup Logo 40
S-video connector 18
Sync Threshhold Adjust 38
System 39
P
Phase 38
Picture menu 36
Power connector 12
power cord 12, 19
Power Save 22, 39
Power switch 13
Power-up Source 39
presentation
features 33
Presets 37
projection distance 8
projector
connecting video devices 17
connector panel 7
customization
34 ProjectorsManual.com Manuals
Downloaded
from
47
T
Tint 36
Tracking 38
troubleshooting 22
turning off
projector 22
TV tuner 17
U
USB, connecting 12
Using 30
V
Vertical 38
video optimizing 34
Video Standard 38
volume adjustment 21
Volume button 31
W
Windows 2000 16
Windows 98 15
Windows ME 16
Windows XP 16
Z
zoom 14, 21
Downloaded from ProjectorsManual.com Manuals
48
™
DLP Projector
Downloaded from ProjectorsManual.com Manuals
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement