ASK Proxima M6 DLP User Guide

ASK Proxima M6 DLP User Guide
> > > > > > >
M6
Reference
Guide
Downloaded from ProjectorsManual.com Manuals
Declaration of Conformity
Canada
Manufacturer: InFocus Corporation, 27500 SW Parkway Avenue, Wilsonville,
Oregon 97070 USA
European Office: Louis Armstrongweg 110, 1311 RL Almere, The Netherlands
We declare under our sole responsibility that this projector conforms to the following
directives and norms:
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Agency Approvals
UL, CUL, TUV
Other specific Country Approvals may apply, please see product certification label.
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
This user’s guide applies to models IN10, M6, LP70+, and M2+.
InFocus reserves the right to alter product offerings and specifications at any time.
Safety: IEC 60950-1: 1st Edition
May, 2004
Trademarks
Microsoft, PowerPoint, Word, Excel and Windows are trademarks or registered trademarks of Microsoft Corporation. Digital Light Processing is a trademark or registered
trademark of Texas Instruments. Adobe and Acrobat are trademarks or registered
trademarks of Adobe Systems Incorporated. InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or trademarks of InFocus Corporation in the
United States and other countries.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by InFocus Corporation may void
authority to operate the equipment.
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interference,
in which case the user may be required to take adequate measures. The typical use is
in a conference room, meeting room or auditorium.
Downloaded from ProjectorsManual.com Manuals
1
Important Operating Considerations for Safety
Table of Contents
Introduction
3
•
Place the projector in a horizontal position no greater than 15 degrees
off axis.
Connecting a computer
5
Required computer connections5
Displaying a computer image
6
Adjusting the image
7
Connecting a video device
8
•
Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
•
Locate the projector at least 4' (1.2 m) away from any heating or cooling
vents.
Shutting down the projector
9
•
Use only the power cord provided. A surge-protected power strip is
recommended.
Troubleshooting your setup
9
•
Refer to this guide for proper startup and shutdown procedures.
Using the keypad buttons
Using the remote control
16
17
•
Warning: Hg – Lamp contains mercury. Manage in accordance
with local disposal laws. See www.lamprecycle.org.
•
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
18
18
18
18
In the unlikely event of a lamp rupture, particles may exit through the
projector side vents. When the projector is turned on, keep people,
food, and drinks out of the "keep out" area around the projector, as
indicated by the "X" area below.
Using the menus
Picture menu
Settings menu
19
20
23
3’
Maintenance
26
Cleaning the lens
26
Cleaning the lamp filter screens 26
Using the security lock
26
Replacing the projection lamp 27
Appendix
Projected image size
/1
m
6m
2’ / 0.
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty booklet.
29
29
Downloaded from ProjectorsManual.com Manuals
2
Introduction
Projector components and features
zoom ring
Your new XGA 1024x768 resolution digital projector is specifically
keypad
designed for portability, connectivity, and collaboration. It is easy to
connect, easy to use, easy to transport, and easy to maintain
Product specifications
To read the latest specifications on your multimedia projector, be sure to
visit our website at www.infocus.com, as specifications are subject to
change.
Accessories
focus ring
The standard accessories that came with your projector are listed in the
included user’s guide. Optional accessories can be found on our website at
www.infocus.com or at your retailer or dealer.
remote control sensor (IR)
Online Registration
connectors
Register your projector on our website at www.infocus.com/register to activate your warranty and receive product updates, announcements, and registration incentives.
remote control sensor (IR)
power connector security lock
foot release
speaker
lamp housing
adjustable foot
Downloaded from ProjectorsManual.com Manuals
leveling foot
3
Connector Panel
The projector provides computer and video connectors:
•
one M1-D/A (HD, DVI, and computer)
•
one S-video
•
one composite RCA video
•
one audio in
Connector panel
Computer
S-video
Audio in
Composite video
Downloaded from ProjectorsManual.com Manuals
4
Connecting a computer
Required computer connections
connect computer cable
Connect the black end of the computer cable to the Computer connector on
the projector. Connect the blue end to the video port on your computer. If
you are using a desktop computer, you first need to disconnect the monitor
cable from the computer’s video port.
Some Macintosh® computers do not have a standard VESA-out video port.
If the supplied computer cable will not connect to your computer, purchase
the appropriate adapter from your Apple® reseller.
computer
audio
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.
The LED turns amber.
NOTE: Always use the power cable that shipped with the projector.
Optional computer connections
To advance slides in a PowerPoint™ presentation using the up and down
arrow buttons on the remote, plug the USB connector on the computer cable
into the USB mouse connector on your computer.
To have sound with your presentation, connect an audio cable (sold separately) to your computer and to the Audio In connector on the projector.
Downloaded from ProjectorsManual.com Manuals
5
Displaying a computer image
Remove the lens cap.
remove lens cap
Press the Power button on the top of the projector or the remote.
press Power button
The LED blinks green and the fans start to run. When the lamp comes on,
the start up screen displays and the Power light is steady green. It can take a
minute for the image to achieve full brightness.
? No startup screen? Get help on page 9.
turn on computer
Turn on your computer.
The computer’s image should appear on the projection screen. If it doesn’t,
press the Source button.
Make sure your laptop’s external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/LCD
key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the
labeled function key simultaneously. Refer to your laptop’s documentation to learn your laptop’s key combination.
activate laptop’s external port
? No computer image? Get help on page 9.
Downloaded from ProjectorsManual.com Manuals
6
Adjusting the image
foot release button
adjust height
Adjust the height of the projector, if necessary, by pressing the release button to extend the elevator foot.
Rotate the leveling foot (located at the bottom back left corner), if necessary.
leveling foot
Position the projector the desired distance from the screen, so that the lens is
perpendicular to the screen.
22
.2
6. ft./
8m
adjust distance
9.9 ft./
3m
3.
3
33 ft./
10m
ft .
/1
m
6.
7
2 m ft /
See page 29 for a table listing screen sizes and distances.
4.9 ft./
1.5m
zoom
Adjust the zoom or focus rings by rotating them until the desired image size
and focus are produced.
adjust zoom and focus
If the image is not square, adjust the vertical digital keystone by using the
buttons on the keypad. Press the upper Keystone button to reduce the
upper part of the image, and press the lower Keystone button to reduce the
lower part.
You can also adjust the keystone via the menus. See page 20.
adjust keystone
Adjust the Contrast or Brightness in the Picture menu.
Downloaded from ProjectorsManual.com Manuals
See page 19 for help with the menus.
7
focus
Connecting a video device
connect S-video and audio cables
If your video device uses a round, four-prong S-video connector, plug the
S-video cable into the S-video Out connector on the video device and into
the Video 1 connector on the projector. If the device uses a composite video
connector, plug the composite video cable into the Composite Out connector on the video device and into the Video 2 connector on the projector.
S-video
audio
For audio, plug a mini-plug audio Y-cable into the Audio in connector on
the projector and into the video device’s left and right audio out connectors.
audio
S-video
connect composite video and audio cables
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.
NOTE: Always use the power cable that shipped with the projector.
video
audio
L
R
video
audio
Downloaded from ProjectorsManual.com Manuals
8
Shutting down the projector
LEDs
The Lamp LED on top of the projector (page 16) will alert you to certain
problems.
The projector automatically blanks the screen after no active source is
detected for 30 minutes. This blank screen helps preserve the life of the projector. The image returns when an active source is detected or a remote or
keypad button is pressed.
A solid red Lamp LED means it is time to change the lamp. See page 27.
A blinking red Lamp LED means different things based on the number of
“blinks”. After blinking 1-5 times, the light turns off for 2 seconds, then the
blinking repeats.
Screen Save
You can make the blank screen appear after five minutes by turning on
Screen Save in the Settings>System menu. See page 24. There are six time
options for the Screen Save feature. They range from five minutes to 30 minutes with five minute intervals.
• 1 blink, lamp won’t turn on: Turn the projector off for at least one
minute, then turn it on again. If the blinking continues, the lamp may
need to be replaced.
Power Save
• 2 blinks: Remaining lamp life is low. Replace the lamp, see page 27.
The projector also has a Power Save feature that automatically turns the
lamp off after no signal is detected for 20 minutes. After 10 additional minutes with no signal, the projector powers down. If an active signal is
received before the projector powers down, the image is displayed. You
must press the Power button to display an image after 30 minutes have
passed. When Power Save is enabled, Screen Save is disabled. See page 24.
• 3 or 4 blinks: Unexpected shut down (3 blinks) or fan failure (4
blinks). Turn the projector off for at least one minute, then turn it on
again. If the blinking continues, the projector may require service; go
to www.infocus.com/support.
• 5 blinks: The projector is overheating. Turn the projector off and
remove anything that may be blocking its air vents. Leave the projector off for at least one minute to let it cool before turning it on again.
Important: Continuous operation at high temperature may reduce the
lifetime of the lamp and/or projector.
Turning off the projector
To turn off the projector, press the Power button and verify that you want to
turn the projector off by pressing the Power button again within 3 seconds.
You can cancel the shutdown by not pressing the Power button a second
time. The lamp turns off and the LED blinks amber for 1 minute while the
fans continue to run to cool the lamp. When the lamp has cooled, the LED
lights amber and the fans stop. Unplug the power cable to completely
power off the projector.
The other LED on top of the projector indicates the normal operating state
of the projector.
• A solid green LED means the projector is on.
• A blinking green LED means the lamp is turning on. A green “blip”
means the projector is in Screen Save or Power Save mode.
• A blinking amber LED means the lamp is either warming up or cooling down to enter standby mode; a solid amber LED means the projector is in standby mode.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section
(page 17). If it does not, troubleshoot the setup.
Downloaded from ProjectorsManual.com Manuals
9
•
Source Troubleshooting
Problem
Solution
Result
No startup screen
Plug power cable in, press Power button.
Remove lens cap.
Correct image
Only startup screen appears
Press the Source button
Activate laptop’s external port
Computer image projected
or restart laptop
No computer image, just the words “Signal out of
range”
Downloaded from ProjectorsManual.com Manuals
Adjust computer refresh rate in Control
Panel>Display>Settings>Advanced>
Adapter (location varies by operating
system)
You may also need to set a different
resolution on your computer, as shown
in the following problem.
10
Computer image projected
For PC: Image fuzzy or cropped
A
A
Set your computer’s display resolution to
the native resolution of the projector
(Start>Settings>Control
Panel>Display>Settings tab, select
1024x768)
Image clear and not cropped
A
For a laptop,
disable laptop
monitor
or turn-on dualdisplay mode
For Macintosh: Image fuzzy or cropped
A
A
Set your computer’s display resolution to
the native resolution of the projector
(Apple menu>System
Preferences>Displays, choose 1024x768)
Downloaded from ProjectorsManual.com Manuals
11
Image clear and not cropped
A
Only my laptop’s background appears, not the
Desktop icons
Disable “Extend my Windows Desktop” in
Control Panel>Display>Settings>Display 2
(location varies by operating system)
Background and Desktop projected
Uncheck this
option, then
click Apply
The video embedded in my PowerPoint
presentation does not play on the screen
Turn off the internal LCD display on your
laptop
Downloaded from ProjectorsManual.com Manuals
12
Embedded video plays correctly
Projector troubleshooting
Problem
Solution
Result
Image not square
Adjust keystone on keypad or Picture menu
Square image
Image not sharp
Adjust the focus lens or Sharpness in the
Picture>Advanced menu
Correct image
AB
AB
Image does not fit 16:9 screen
Change aspect ratio to 16:9 in
Picture>Aspect ratio menu
Downloaded from ProjectorsManual.com Manuals
13
Correct image
Image reversed left to right
Turn off Rear in Settings>System menu
A
Projected colors don’t match source
AB
Adjust color, tint, color temperature,
brightness, contrast in the menus
COLOR
Image not centered on screen
Lamp won’t turn on, Lamp LED is blinking red (5
blinks)
Correct image
Correct image
COLOR
Move projector, adjust zoom, adjust height
Adjust horizontal or vertical position in
Picture>Advanced menu
Correct image
Make sure vents aren’t blocked; allow
projector to cool for one minute
Unplug projector; wait one minute; plug in
projector and turn it on: lamp lights
Downloaded from ProjectorsManual.com Manuals
14
“Change lamp” message appears at startup, lamp
won’t turn on, lamp won’t turn on, Lamp LED is
blinking red (2 blinks)
Lamp must be replaced (page 27)
Still having problems?
If you need assistance, visit the Service and Support section of our website
or call us.
This product is backed by a limited warranty. An extended warranty plan
may be purchased from your dealer. When sending the projector in for
repair, we recommend shipping the unit in its original packing material, or
having a professional packaging company pack the unit. Please insure your
shipment for its full value.
Downloaded from ProjectorsManual.com Manuals
15
Lamp turns on
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of their functions:
power–turns the projector on (page 6) and off.
LED
menu–opens the on-screen menus (page 19).
source/select–confirms choices made in the menus and selects sources
(page 19).
up/down/left/right arrows–navigates to and adjusts settings in the menus
(page 19).
keystone–vertical keystone adjusts the squareness of the image (page 7).
You can also adjust the keystone via the menus. See page 20.
volume–adjusts sound (page 18).
Downloaded from ProjectorsManual.com Manuals
16
Using the remote control
The remote uses two (2) AA batteries. They are easily installed by sliding
the cover off the remote’s back, aligning the + and - ends of the batteries,
sliding them into place, and then replacing the cover.
navigation
buttons
Caution: When replacing the batteries, be aware that using batteries other
than the type provided with the projector may risk severe damage to the
remote. When disposing of the batteries, be sure to do so in an environmentally proper manner.
To operate, point the remote at the front of the projector (not at the computer). The range of optimum operation is about 15 feet (4.5m).
Press the remote’s Power button to turn the projector on and off (see page 9
for shutdown info).
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 19 for more info on the menus.
The remote also has a Source button to switch between sources.
If you connect the USB portion of the M1-DA computer cable (page 5) you
can use the up and down arrow navigation buttons to advance slides in a
PowerPoint presentation.
Troubleshooting the remote
•
Make sure the batteries are installed in the proper orientation and are
not dead.
•
Make sure you’re pointing the remote at the projector or the screen, not
the computer, and are within the remote range of 15 feet (4.5m). For
best results, point the remote at the projector.
Downloaded from ProjectorsManual.com Manuals
17
Optimizing computer images
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
menu. See page 20.
After your computer is connected properly and the computer’s image is on
the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 19.
•
Change the Aspect ratio. Aspect ratio is the ratio of the image width to
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your
input source. See page 20.
•
Adjust the Keystone, Contrast, or Brightness in the Picture menu.
•
Change the Aspect Ratio. See page 20 for details.
•
•
Adjust the Color Space, Temperature or Control in the Advanced
menu.
Select a Sharpness, Color Temperature, or Video Standard setting. See
page 22.
•
Adjust the Color Control or White Peaking settings. See page 22.
•
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced menu.
Customizing the projector
•
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
settings later. See page 21.
You can customize the projector for your specific setup and needs. See
page 23 for details on these features.
•
For rear projection, turn Rear mode on in the Settings>System menu.
Presentation features
•
Specify which source the projector checks first for active video during
power-up.
Several features are provided to make giving presentations easier. The following is an overview, details are found in the menu section on page 19.
•
Specify the function of the Custom Key on the optional remote.
•
Turn the projector’s display messages on and off.
•
The Custom key, available on several optional remotes only, allows you
to assign various features to the button. See page 25 for details.
•
Turn on power saving features.
•
The Startup Logo menu option lets you change the default startup
screen to a black, white, or blue screen. See page 24.
•
Specify blank screen colors and startup logos.
•
Specify the menu language.
•
Two menu options, Power Save and Screen Save, are provided to automatically shut down the projector after several minutes of inactivity or
display a blank screen. This helps preserve lamp life. See page 24.
•
Control your projector using RS-232 commands.
Optimizing video images
After the video device is connected properly and the image is on the screen,
you can optimize the image using the onscreen menus. For general information on using the menus, see page 19.
Downloaded from ProjectorsManual.com Manuals
18
Using the menus
To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to highlight the desired submenu, then press the Select button.
Menu
button
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio buttons, or turn the feature on or off using check boxes. Press Select to confirm
your changes. Use the arrows to navigate to another setting. When your
adjustments are complete, navigate to Exit, then press Select to go to the
previous menu; press the Menu button at any time to close the menus.
Main menu
Dots appear before the menu name. The number of dots indicate the menu’s
level, ranging from one (the Main menu) to four (the most nested menus).
remote navigation
buttons
Dots
The menus are grouped by usage:
•
The Picture menu provides image adjustments.
•
The Settings menu provides set-up type adjustments that are not
changed often.
•
The Source Info menu provides a read-only display of information
about the projector and source.
Settings
menu
Certain menu items may be grayed out until a particular source is connected. For example, Sharpness is only available for video sources and will
be hidden when a computer source is active. Other menu items may be
grayed out when they are not available. For example, Brightness is grayed
out until an image is active.
Picture
menu
Source Info menu
Downloaded from ProjectorsManual.com Manuals
19
Picture menu
To adjust the following six settings, highlight the setting, press Select, use
the up and down arrows to adjust the values, then press select to confirm
the changes.
increasing keystone
Keystone: adjusts the image vertically and makes a squarer image. You can
also adjust keystone from the keypad.
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
Brightness: changes the intensity of the image.
Color: (video and component sources only) adjusts a video image from
black and white to fully saturated color.
Tint: (NTSC video sources only) adjusts the red-green color balance in the
image.
Auto Image: resynchs the projector to the source.
Aspect Ratio
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are
1.78:1, or 16:9. The default is 4:3, which displays the input resized up or
down to fill the display area.
The aspect ratio selection is saved for each source.
Downloaded from ProjectorsManual.com Manuals
20
decreasing keystone
Presets: Presets are provided that optimize the projector for displaying
computer presentations, film images, and video images. Film input is material originally captured on a film camera, like a movie; video input is material originally captured on a video camera, like a TV show or sporting event.
There are also user-definable presets. To set a preset for the current source,
adjust the image, select Save Settings in the Presets menu, then select Save
User 1 (or 2 or 3). You can recall these settings in the future by selecting the
User 1 preset.
Presets
If you make any adjusts the image, Presets Off will automatically be
selected in the Preset menu to indicate changes have been made.
To restore the factory default settings, choose Factory Reset in the Settings>Service menu.
Downloaded from ProjectorsManual.com Manuals
21
Advanced settings
Advanced
The following 4 options are for computer and component sources only.
Phase: adjusts the horizontal phase of a computer source.
Tracking: adjusts the vertical scan of a computer source.
Horizontal/Vertical Position: adjusts the position of a computer source.
Sync Threshold Adjust: (enhanced and high definition sources only) If a
hardware device, such as a DVD player, is not syncing properly with the
projector, select this option to help it sync.
White Peaking: (video sources only) adjusts the white level processed in
the image. It increases the brightness of whites that are near 100%.
Sharpness
Overscan: (video sources only) removes noise around the video image.
Sharpness: (video sources only) changes the clarity of the edges of a video
image. Select a sharpness setting.
Color Space: This option applies to computer sources. It allows you to
select a color space that has been specifically tuned for the video input.
When Auto is selected, the projector automatically determines the standard.
To choose a different setting, turn off Auto, then choose RGB for computer
sources, choose either REC709 or REC601 for component sources.
Color Temperature
Color Space
Color Temperature: changes the intensity of the colors. Select a listed
value.
Color Control: allows you to individually modify each color. Highlight the
color, press Select, then use the arrows to adjust the value.
Video Standard: (video sources only) When it is set to Auto, the projector
attempts to pick the video standard automatically based on the input signal
it receives. (The video standard options may vary depending on your region
of the world.) If the projector is unable to detect the correct standard, the
colors may not look right or the image may appear “torn.” If this happens,
manually select a video standard by selecting NTSC, PAL, or SECAM from
Downloaded
from
ProjectorsManual.com Manuals
the Video
Standard
menu.
Video Standard
22
Color Control
Settings menu
Audio: allows adjustments to the volume.
Sources: allows you to assign a particular input to a specific source key
when using an optional remote. Also allows selection of a default Power-up
Source and enables or disables Autosource.
Audio
Settings
Sources>Autosource: When Autosource is not checked, the projector
defaults to the source selected in Power-up Source. If no source is found, a
blank screen displays. When Autosource is checked, Power-up Source
determines which source the projector defaults to at startup. If no signal is
present, the projector checks the sources in order until a source is found or
until power down.
Sources>Power-up Source: this determines which source the projector
checks first for active video during power-up.
Sources>Source Enable: When Autosource is selected, the Source Enable
feature indicates which sources the projector attempts to lock onto. You can
use the Source Enable feature to eliminate certain sources from this search,
which will speed the search. By default, the check boxes for all sources are
checked.
Sources
System>OSD Offset: allows you to adjust the position of the OSD. By
default, the menus are positioned in the upper lefthand corner of the displayed image and the messages are positioned in the lower lefthand corner.
Adjust the offset to move these items more to the right and middle of the
display.
Power-up
Source
Rear: reverses the image so you can project from behind a translucent
screen.
Auto Power: When Auto Power is checked, the projector automatically
goes into the startup state after the projector is powered on.
Display Messages: displays status messages (such as “Searching” or
“Mute”) in the lower-left corner of the screen.
System
Downloaded from ProjectorsManual.com Manuals
23
PC Screen Saver Off: prevents your computer from going into Screen Save
mode. This feature is only available if the USB portion of the computer cable
is connected to your computer (page 5).
Power Save: automatically turns the lamp off after no signals are detected
for 20 minutes. After 10 additional minutes with no signal, the projector
powers down. If an active signal is received before the projector powers
down, the image will be displayed.
Screen Save: automatically blanks the screen with a black color after no signals are detected for a preset number of minutes. The image returns when
an active source is detected or a remote or keypad button is pressed. Screen
Save is disabled when Power Save is enabled.
Screen Save
System
Startup Logo: allows you to display a blank Black, White, or Blue screen
instead of the default screen at startup and when no source is detected.
Startup Logo
Blank Screen: determines what color is displayed when no source is
detected3.
Blank Screen
Downloaded from ProjectorsManual.com Manuals
24
Custom Key (for use with optional remote only): allows you to assign a different function to the Custom button on the remote to quickly and easily
use the effect. Only one effect can be enabled at a time. Highlight an effect
and press Select to choose a different one. The default effect is About.
•
Blank: displays an empty screen.
•
Mute: turns off all sound.
•
Aspect Ratio: toggles among 4:3, 16:9, and Native (see page 20).
•
Source: cycles through available sources.
•
Auto Image: resets the projector to the source.
•
Freeze: pauses the projected image.
•
Source Info: the default effect. It opens a window with projector and
source information.
•
Service Info: opens a window with projector and source information.
Custom Key
Language: allows you to select a language for the onscreen display of
menus and messages.
Language
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp Hours) to their default
after displaying a confirmation dialog box.
Reset Lamp Hours: resets the lamp hours counter in the Service Info menu
to zero. Do this only after changing the lamp. It displays a confirmation dialog box.
Test Pattern: allows you to display certain patterns to adjust the image.
This feature only works with an optional remote. To display test patterns,
click the Test Pattern check box, exit the menus, then press the Blank button
on the remote. To select the patterns, use the up/down arrows on the
remote or keypad. To exit the test patterns, press the Blank button again.
Service menu
Service Info: provides information about the projector and lamp.
Service Code: only used by authorized service personnel.
Downloaded from ProjectorsManual.com Manuals
25
Maintenance
Using the security lock
Cleaning the lens
The projector has a security lock for use with a cable lock system. Refer to
the information that came with the lock for instructions on how to use it.
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you
don’t intend to use the projector immediately, replace the lens cap.
Cleaning the lamp filter screens
In dirty or dusty environments, the dust filter screens on and
around the lamp module can become clogged, causing high temperatures inside the lamp module. These high temperatures can impact
lamp performance and operating life. Routine maintenance to remove
dust and dirt from the screens lowers the lamp operating temperature and prolongs lamp life. To maximize lamp life you will need to
clean the screens every 250 hours. Lamp screen maintenance may need to
occur more often than 250 hours depending on your installation/use environment.
1 Remove the lamp module. Refer to “Replacing the projection lamp”
on page 27 for instructions.
2 Examine the dust filter screens on the lamp module and in the
lamp housing area. If necessary, use a vacuum cleaner set on low
power to clean the screens. Be careful not to disturb any internal
components when cleaning the screens.
3 Replace the lamp module.
Downloaded from ProjectorsManual.com Manuals
26
Replacing the projection lamp
The lamp hour timer in the Service Info menu counts the number of hours
the lamp has been in use. Twenty hours before the specified end of the
lamp’s life, the message “Replace lamp” briefly appears on the screen at
each startup. When the expected lamp life has been reached, the Lamp indicator icon lights red.
Service Info menu
NOTE: You can order new lamp housings from www.infocus.com (in select
areas), your retailer or your dealer. Use only a replacement lamp with the
same type and rating as the original lamp.
turn off and unplug
the projector
1 Turn off the projector and unplug the power cable.
wait 60 minutes
2 Wait 60 minutes to allow the projector to cool thoroughly.
3 Turn the projector upside down and loosen the captive screw on the
loosen the screw on lamp door
lamp door. The lamp door is part of the lamp housing.
4 Insert the screwdriver in the tab on the lamp door and pry the door up.
WARNINGS:
•
To avoid burns, allow the projector to cool for at least 60 minutes before
you replace the lamp.
•
Unplug the power cord before replacing the lamp.
•
Do not drop the lamp module. The glass may shatter and cause injury.
•
Do not touch the glass lamp screen. Fingerprints can obscure projection
sharpness.
pry the lamp door off
tab
Downloaded from ProjectorsManual.com Manuals
27
•
Be extremely careful when removing the lamp housing. In the unlikely
event that the lamp ruptures, small glass fragments may be generated.
The lamp module is designed to contain most of these fragments, but
use caution when removing it. Before replacing a ruptured lamp, clean
the lamp compartment and dispose of cleaning materials. Wash hands
after lamp replacement.
remove lamp housing
Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
5 Carefully remove the lamp housing. Dispose of the lamp in an environmentally proper manner.
6 Install the new lamp housing. Be careful to attach the connector on the
lamp housing to the connector inside the projector. These connectors are
located near the leveling foot.
7 Tighten all three screws.
8 Plug in the power cable then press the Power button to turn the projector back on, then reset the lamp hour timer.
reset lamp time in Service menu
Resetting the lamp timer
To reset the lamp timer, navigate to the Settings>Service menu and select
Reset Lamp Hours.
Downloaded from ProjectorsManual.com Manuals
28
Appendix
Projected image size
Table 1:
Image Size, Width and Height for Lens at Maximum Image Size
Distance to
Screen (feet/m)
4.9/1.5
7.4/2.3
9.9/3.0
12.3/3.8
18.5/5.6
32.8/10.0
Diagonal
(inches/m)
40/1
60/1.5
80/2
100/2.5
150/3.8
266/6.8
Width
(inches/m)
32/.8
48/1.2
64/1.6
80/2
120/3
213/5.4
Height
(inches/m)
24/.6
36/.9
48/1.2
60/1.5
90/2.3
160/4.1
Table 2:
Image Size, Width and Height for Lens at Minimum Image Size
Distance to
Screen (feet/m)
4.9/1.5
7.4/2.3
9.9/3.0
12.3/3.8
18.5/5.6
32.8/10.0
Diagonal
(inches/m)
31/.8
47/1.2
63/1.6
79/2
118/3
209/5.3
Width
(inches/m)
25/.64
38/1
50/1.3
63/1.6
94/2.4
167/4.2
Height
(inches/m)
19/.48
28/.7
38/.8
47/1.2
71/1.4
125/3.3
NOTE: Visit our website for an interactive image size calculator.
Downloaded from ProjectorsManual.com Manuals
29
D
Display Messages 23
displaying, image 6
INDEX
Numerics
1024x768 resolution 3
A
Advanced setting 22
Aspect Ratio 20, 25
Audio In connector 5, 8
Auto Power 23
Autosource 23
E
elevator foot 7
F
Factory Reset 25
focus 7
fuzzy image 11
B
Blank screen 24
Brightness 7
I
image does not fit screen 13
image not centered 14
image not sharp 13
image not square 13
image reversed 14
image size matrix 29
image, displaying 6
C
cleaning the lamp filter screens 26
cleaning the lens 26
Color 20
Color Control 22
Color Space 22
Color Temperature 22
colors are incorrect 14
computer connections
optional 5
required 5
computer image
optimize 18
troubleshooting 10
connecting
computer 5
video device 8
connector panel 4
contacting InFocus 15
Contrast 7, 20
Custom key 18
customer service contact information 15
K
keypad buttons 16
keystone 7, 20
Downloaded from ProjectorsManual.com Manuals
30
L
lamp
cleaning filter screens 26
lamp replacement 27
Lamp Reset 25
lamp won’t turn on 14, 15
Language 25
laptop
connecting 5
external video port 6
LED 9
lens, cleaning 26
leveling foot 7
lock, security 26
Low Power 23
P
PC Screen Saver 24
Picture menu 20
Position 22
power cable 5, 8
Power Save 9, 24
Power-up Source 23
presentation features 18
projected image sizes 29
projector
adjusting the height 7
connector panel 4
customizing 18
positioning 7
registering 3
safety considerations 2
shutdown 9
troubleshooting problems 9
M
Macintosh troubleshooting 11
Main menu 19
menu system 19
R
Rear 23
remote control 17
replacing the lamp 27
Reset 25
resetting the lamp timer 28
resolution 3
N
no computer image 10
no startup screen 10
O
only startup screen appears 10
onscreen menus 19
Overscan 22
Downloaded from ProjectorsManual.com Manuals
31
S
Screen Save 9, 24
security lock 26
Service 25
Settings menu 23
Sharpness 22
shutting down the projector 9
Sources 23
Startup Logo 24
Sync Threshold Adjust 22
U
using the keypad buttons 16
T
Tint 20
Tracking 22
Troubleshooting 9
Turning off the projector 9
X
XGA 3
V
video connections 8
video images, optimizing 18
Video Standard 22
W
White Peaking 22
Z
zoom 7
Downloaded from ProjectorsManual.com Manuals
32
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement