Boxlight Cinema 20HD Projector User Guide

Boxlight Cinema 20HD Projector User Guide

DRAFT

USER'S GUIDE

CINEMA 20HD

HOME THEATER

PROJECTOR

Downloaded from ProjectorsManual.com Manuals

TO THE OWNER

Before operating this projector, read this manual thoroughly and operate the projector properly.

This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time.

Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.

If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center.

SAFETY PRECAUTIONS

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

This projector produces intense light from the projection lens. Do not stare directly into the lens as possible.

Eye damage could result. Be especially careful that children do not stare directly into the beam.

This projector should be set in the way indicated. If not, it may result in a fire hazard.

SIDE and TOP ●

Take appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector.

Minimum distance should be taken. If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous.

20cm

50cm 50cm

REAR

50cm

Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes.

If the projector is not to be used for an extended time, unplug the projector from the power outlet.

READ AND KEEP THIS USER'S GUIDE FOR LATER USE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS

VOLTAGE CONSTITUTING A RISK OF ELECTRIC

SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT

OPERATING AND MAINTENANCE INSTRUCTIONS IN THE

USER'S GUIDE WITH THIS UNIT.

2

Downloaded from ProjectorsManual.com Manuals

SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before the product is operated.

Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.

Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table.

The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the projector.

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the projector.

c. If the projector has been exposed to rain or water.

d. If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has been damaged.

f. When the projector exhibits a distinct change in performance-this indicates a need for service.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

Voor de klanten in Nederland

Bij dit product zijn batterijen geleverd.

Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.

Downloaded from ProjectorsManual.com Manuals

3

COMPLIANCES

Federal Communication Commission Notice

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Number

Trade Name

Responsible party

Address

Telephone No.

: CINEMA 20HD

: Boxlight

: BOXLIGHT

: 19332 Powder Hill Place Poulsbo, WA 98370-7407 USA

: (800)762-5757

AC POWER CORD REQUIREMENT

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters

Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician.

GROUND

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

4

Downloaded from ProjectorsManual.com Manuals

TABLE OF CONTENTS

FEATURES AND DESIGN

PREPARATION

NAME OF EACH PART OF PROJECTOR

SETTING-UP PROJECTOR

CONNECTING AC POWER CORD

POSITIONING PROJECTOR

ADJUSTABLE FEET

MOVING PROJECTOR

6

7

7

8

8

9

10

10

COMPUTER MODE

SELECTING INPUT SOURCE

SELECTING COMPUTER SYSTEM

PC ADJUSTMENT

AUTO PC ADJUSTMENT

MANUAL PC ADJUSTMENT

COMPATIBLE COMPUTER SPECIFICATIONS

PICTURE IMAGE ADJUSTMENT

IMAGE LEVEL SELECT

IMAGE LEVEL ADJUSTMENT

PICTURE SCREEN ADJUSTMENT

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR

CONNECTING TO COMPUTER

CONNECTING TO VIDEO EQUIPMENT

BEFORE OPERATION

OPERATION OF REMOTE CONTROL

LASER POINTER FUNCTION

REMOTE CONTROL BATTERIES INSTALLATION

TOP CONTROLS AND INDICATORS

OPERATING ON-SCREEN MENU

HOW TO OPERATE ON-SCREEN MENU

FLOW OF ON-SCREEN MENU OPERATION

MENU BAR

BASIC OPERATION

TURNING ON / OFF PROJECTOR

ADJUSTING SCREEN

ZOOM ADJUSTMENT

FOCUS ADJUSTMENT

LENS SHIFT ADJUSTMENT

KEYSTONE ADJUSTMENT

PICTURE FREEZE FUNCTION

NO SHOW FUNCTION

SOUND ADJUSTMENT

11

11

12

13

14

VIDEO MODE

SELECTING INPUT SOURCE

SELECTING VIDEO SYSTEM

PICTURE IMAGE ADJUSTMENT

IMAGE LEVEL SELECT

IMAGE LEVEL ADJUSTMENT

PICTURE SCREEN ADJUSTMENT

14

14

15

16

17

17

17

18

SETTING

SETTING MENU

19

19

20

20

20

20

20

21

21

21

APPENDIX

MAINTENANCE

WARNING TEMP. INDICATOR

AIR FILTER CARE AND CLEANING

CLEANING PROJECTION LENS

LAMP REPLACEMENT

LAMP REPLACE COUNTER

TROUBLESHOOTING

TECHNICAL SPECIFICATIONS

37

37

39

39

39

39

39

40

41

42

44

22

27

27

28

30

22

22

23

23

24

26

31

31

32

33

33

34

36

TRADEMARKS

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.

IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

Windows and PowerPoint are registered trademarks of Microsoft Corporation.

Each name of corporations or products in the user's guide is a trademark or a registered trademark of its respective corporation.

Downloaded from ProjectorsManual.com Manuals

5

FEATURES AND DESIGN

This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.

Compact Design

This projector is extremely compact in size and weight.

It is designed to carry and work anywhere you wish to use.

Compatibility

This projector widely accepts various video and computer input signals including;

Computers

IBM-compatible or Macintosh computer up to 1280 x 1024 resolution.

6 Color Systems

NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL-

N color system can be connected.

Component Video

Component video signal, such as a DVD player output high definition TV signals including 480i,

480p, 575i, 575p, 720p, 1035i or 1080i, can be connected.

S-Video

S-Video signal, such as a S-VHS VCR output signal, can be connected.

High Resolution Image

This projector provides 1366 x 768 dots resolution for computer input and 800 horizontal TV lines. Resolution from a computer between XGA (1024 x 768) and SXGA

(1280 x 1024) is compressed into 1024 x 768 dots. This projector cannot display image of over 1280 x 1024 dots.

When resolution of your computer is over than 1280 x

1024, reset a computer output for lower resolution.

Multi-Scan System

This projector has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for troublesome manual adjustment of frequency and other settings.

Digital Zoom (for Computer)

Digital Zoom function adjusts image size to approx. 1/4 ~

49 times of original image size, allowing you to focus on crucial information at a presentation.

Keystone Correction

Positioning of a projector may result in distorted image being displayed in a trapezoid shape. Keystone

Correction solves this problem by digitally altering projection to produce undistorted images.

Power Management

Power Management function is provided to reduce power consumption while a projector is not in use.

This Power Management function operates to turn

Projection Lamp off when a projector detects signal interruption and any button is not pressed over 5 minutes. Projection Lamp is automatically turned on again when a projector detects signal or any operation button is pressed.

This projector is shipped with this function ON.

Digital Visual Interface

This projector is equipped with DVI 24-pin terminal for connecting DVI output from a computer.

Multilanguage Menu Display

Operation menu is displayed in; English, German,

French, Italian, Spanish, Portuguese, Dutch, Swedish,

Chinese, Korean or Japanese.

Network connection (Optional)

Network connection is an optional product to control and set up a projector via the network cable. By accessing to the connected projector using the web browser on your computer. It can be controlled and set up the projector remotely. Contact the sales dealer where you purchased this projector for optional parts.

One-Touch Auto PC Adjustment

Incoming computer video signals are recognized and best adjustment is automatically set by Auto PC

Adjustment. No complicated setup is necessary and projection is always precise.

Motor-driven Lens Shift

Projection lens can be moved up and down with motordriven lens shift function. This function makes it easy to provide projected image where you want.

Zoom and focus can be also adjusted with motor-driven operation.

6

Downloaded from ProjectorsManual.com Manuals

PREPARATION

NAME OF EACH PART OF PROJECTOR

FRONT OF CABINET

TOP CONTROLS

AND INDICATORS

PROJECTION LENS

AIR INTAKE

VENT

LENS COVER

SPEAKERS

INFRARED

REMOTE RECEIVER

BACK OF CABINET

EXHAUST VENT

POWER CORD

CONNECTOR

TERMINALS

AND CONNECTORS

INFRARED

REMOTE RECEIVER

HOT AIR EXHAUSTED !

Air blown from exhaust vent is hot. When using or installing a projector, following precautions should be taken.

Do not put a flammable object near this vent.

Keep rear grills at least 3’(1 m) away from any object, especially heat-sensitive object.

Do not touch this area, especially screws and metallic parts. This area will become hot while a projector is used.

This projector detects internal temperature and automatically controls operating power of Cooling Fans.

LAMP COVER

When attached the network connection to the projector, remove the these parts.

CARRYING

HANDLE

BOTTOM OF CABINET

AIR INTAKE VENTS

This projector is equipped with cooling fans for protection from overheating. Pay attention to following to ensure proper ventilation and avoid a possible risk of fire and malfunction.

Do not cover vent slots.

Keep side clear of any objects. Obstructions may block cooling air.

ADJUSTABLE FEET

AND

FEET LOCK LATCHES

Downloaded from ProjectorsManual.com Manuals

7

PREPARATION

SETTING-UP PROJECTOR

CONNECTING AC POWER CORD

This projector uses nominal input voltages of 100-120 V or 200-240

V AC. This projector automatically selects correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system.

Consult your authorized dealer or service station if you are not sure of type of power supply being in use.

Connect a projector with a peripheral equipment before turning a projector on. (Refer to pages 11 ~ 13 for connection.)

CAUTION

For safety, unplug AC Power Cord when an appliance is not used.

When this projector is connected to outlet with AC Power Cord, an appliance is in Stand-by Mode and consumes a little electric power.

Connect AC Power Cord (supplied) to a projector.

AC outlet must be near this equipment and must be easily accessible.

NOTE ON POWER CORD

AC Power Cord must meet requirement of country where you use a projector.

Confirm AC plug type with chart below and proper AC power cord must be used.

If supplied AC Power Cord does not match AC outlet, contact your sales dealer.

Projector side AC Outlet side

For U.S.A. and Canada

For Continental Europe

Ground

To POWER CORD

CONNECTOR on a projector.

To AC Outlet.

(120 V AC)

To AC Outlet.

(200 - 240 V AC)

8

Downloaded from ProjectorsManual.com Manuals

PREPARATION

POSITIONING PROJECTOR

This projector is designed to project on a flat projection surface.

Projector can be focused from 5.0’ (1.5m) ~ 51.3’

(15.6m).

Refer to figure below to adjust screen size.

ROOM LIGHT

Brightness in room has a great influence on picture quality. It is recommended to limit ambient lighting in order to provide best image.

12.7’(3.9m)

5.0’(1.5m)

40”

100”

77”

31”

25.6’(7.8m)

200”

154”

38.4’(11.7m)

300”

51.3’(15.6m)

Max. Zoom

400”

308”

231”

Min. Zoom

Screen

Size

Max. Zoom

Min. Zoom

Distance

40”

31”

5.0’ (1.5m)

100”

77”

12.7’ (3.9m)

150”

115”

19.1’ (5.8m)

200”

154”

25.6’ (7.8m)

250”

192”

32.0’ (9.8m)

300”

231”

38.4’ (11.7m)

400”

308”

51.3’ (15.6m)

LENS SHIFT ADJUSTMENT

Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to provide projected image where you want. Refer to P 20 for operation.

Highest Lens Shift Lowest Lens Shift

H3

H1

H1 : H2 = 6 : 1

H2

H4

H3 : H4 = 1 : 1

NOTE

Screen size and lens shift ratio on the above charts are standard values and they may change by positioning conditions.

Downloaded from ProjectorsManual.com Manuals

9

PREPARATION

ADJUSTABLE FEET

Picture tilt and projection angle can be adjusted by rotating ADJUSTABLE FEET. Projection angle can be adjusted to 10.5 degrees.

1

2

3

Lift front of a projector and pull FEET LOCK LATCHES on both sides of a projector.

Release FEET LOCK LATCHES to lock ADJUSTABLE

FEET and rotate ADJUSTABLE FEET to fine tune position and tilt.

To shorten ADJUSTABLE FEET, lift front of a projector and pull and undo FEET LOCK LATCHES.

Position and keystone distortion of image can be adjusted using Menu Operation. (Refer to P 20 and 37.)

ADJUSTABLE FEET

NOTE :

THIS PROJECTOR SHOULD BE SET IN THE WAY

INDICATED. PROJECTION LAMP MAY MALFUNCTION.

MOVING PROJECTOR

Use Carry Handle when moving a Projector.

When moving a projector, replace lens cover and retract feet to prevent damage to lens and cabinet.

When this projector is not in use for an extended period, put it into case (dust cover) supplied with this projector.

FEET LOCK

LATCHES

CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR

Do not drop or bump a projector, otherwise damages or malfunctions may result.

When carrying a projector, use a suitable carrying case.

Do not transport a projector by using a courier or transport service in an unsuitable transport case. This may cause damage to a projector. To transport a projector through a courier or transport service, consult your dealer for best way.

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR

This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on pages 11 to 13 and connect properly.

COMPUTER AUDIO

INPUT (1 and 2) JACKS

Connect an audio output

(stereo) from computer to these jacks.

(Refer to P12.)

COMPUTER INPUT

TERMINALS (DIGITAL/ANALOG)

Connect computer (digital/analog) output to one of these terminals.

(Refer to P12.)

ANALOG

INPUT 1

DIGITAL(DVI-D)

R/C JACK

R/C JACK

When using Wired/Wireless

Remote Control Unit as Wired

Remote Control, Connect

Wired Remote Control Unit to this jack with Remote Control

Cable (supplied).

AUDIO 1

RESET

AUDIO 2

CONTROL PORT

RESET BUTTON

This projector uses a micro processor to control this unit, and occasionally, this micro processor may malfunction and need to be reset. This can be done by pressing RESET button with a pen, which will shut down and restart unit. Do not use RESET function excessively.

Do not press this button. This button is used for our optional accessories.

G B R H/V

INPUT 3

(MONO)

V

VIDEO/Y Cb/Pb

VIDEO/Y Cb/Pb Cr/Pr

Cr/Pr

INPUT 2

R–AUDIO–L

S–VIDEO

CONTROL PORT CONNECTOR

When controlling this projector by computer, connect your computer to this terminal.

(Refer to P12.)

5 BNC INPUT JACKS

Connect component video output (Y, Cb, Cr or Y, Pb, Pr) from video equipment to

VIDEO/Y, Cb/Pb and Cr/Pr jacks or connect computer output {5 BNC Type (Green,

Blue, Red, Horiz. Sync and

Vert. Sync.)} from computer to G, B, R, H/V and V jacks.

(Refer to P12 and 13.)

VIDEO INPUT JACKS

Connect composite video output from video equipment to VIDEO/Y jack or connect component video outputs to

VIDEO/Y, Cb/Pb and Cr/Pr jacks. (Refer to P13.)

AUDIO INPUT JACKS

Connect an audio output from video equipment to these jacks.

(Refer to P13.)

S-VIDEO INPUT JACK

Connect S-VIDEO output from video equipment to this jack. (Refer to P13.)

Downloaded from ProjectorsManual.com Manuals

11

CONNECTING PROJECTOR

CONNECTING TO COMPUTER

Cables used for connection

(

= Cable or adapter is not supplied with this projector.)

• VGA Cable (HDB 15 pin)

• DVI-Digital Cable (for Single Link T.M.D.S.)

• BNC Cable

• Control Cable for Serial Port

• MAC Adapter (When connecting to Macintosh computer)

• Audio Cable {Mini Plug (stereo) x 1}

IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)

Desktop type Laptop type

Monitor Output Audio Output

Serial port

Monitor Output

BNC

Cable

MAC Adapter

Set slide switches according to chart below.

VGA Cable

DVI

Cable

Audio

Cable

(stereo)

COMPUTER

AUDIO IN 1 or 2

COMPUTER IN ANALOG

COMPUTER IN DIGITAL

ANALOG

INPUT 1

DIGITAL(DVI-D)

R/C JACK

AUDIO 1

RESET

AUDIO 2

CONTROL PORT

G B R H/V V

VIDEO/Y Cb/Pb

VIDEO/Y Cb/Pb Cr/Pr

Cr/Pr

INPUT 2

R–AUDIO–L

S–VIDEO

INPUT 3

(MONO)

Terminals of a Projector

Control Cable for Serial Port

Terminal

CONTROL

PORT

MAC ADAPTER

Set switches as shown in table below depending on RESOLU-

TION MODE that you want to use before you turn on projector and computer.

ON

OFF

13" MODE (640 x 480)

16" MODE (832 x 624)

19" MODE (1024 x 768)

21" MODE (1152 x 870)

1 2

ON ON

OFF ON

OFF

ON

ON

ON

ON DIP

1 2 3 4 5 6

3

OFF

OFF

ON

ON

4 5 6

OFF OFF OFF

ON OFF OFF

OFF OFF OFF

ON OFF OFF

NOTE :

When connecting cable, power cords of both a projector and external equipment should be disconnected from AC outlet. Turn a projector and peripheral equipment on before computer is switched on.

CONNECTING PROJECTOR

CONNECTING TO VIDEO EQUIPMENT

Cables used for connection

(

= Cable is not supplied with this projector.)

• Video Cable (RCA x 1), or (RCA x 3)

• BNC Cable

• S-VIDEO Cable

• Audio Cable (RCA x 2)

Video Source (example)

Video Cassette Recorder Video Disc Player

Component video output equipment.

(such as DVD player or high-definition TV source.)

Composite

Video Output

Component Video Output

(Y, Cb/Pb, Cr/Pr)

Composite

Video Output

Component Video Output

(Y, Cb/Pb, Cr/Pr)

Audio Output S-VIDEO Output

Video Cable

(

RCA x 1

)

Video Cable

(

RCA x 3

)

BNC Cable

Audio Cable

(RCA x 2)

S-VIDEO

Cable

VIDEO

Y - Cb/Pb - Cr/Pr VIDEO

Y - Cb/Pb - Cr/Pr AUDIO IN S-VIDEO

NOTE :

When connecting cable, power cords of both a projector and external equipment should be disconnected from AC outlet.

ANALOG

INPUT 1

DIGITAL(DVI-D)

R/C JACK

AUDIO 1

RESET

AUDIO 2

CONTROL PORT

G B R H/V V

VIDEO/Y Cb/Pb

VIDEO/Y Cb/Pb Cr/Pr

Cr/Pr

INPUT 2

R–AUDIO–L

S–VIDEO

INPUT 3

(MONO)

Terminals of a Projector

Downloaded from ProjectorsManual.com Manuals

13

BEFORE OPERATION

OPERATION OF REMOTE CONTROL

Left Side

LENS SHIFT BUTTON

Used to select LENS

SHIFT function. (P20)

MENU BUTTON

Used to select MENU operation. (P17, 18)

LENS SHIFT

LENS

KEYSTONE

ON-OFF

KEYS

MENU SCREEN

E

M

O

V

SELECT

V

O

L

LIGHT SWITCH

Slide this switch, to illuminate key on remote control unit for 10 seconds.

INPUT BUTTON

Used to select input source. (P22)

MUTE BUTTON

Used to mute sound. (P21)

AUTO PC ADJ. BUTTON

Used to operate AUTO PC

Adjustment function. (P23)

INPUT

INPUT

1

IMAGE

1

IMAGE

2

2 3 4

3

MUTE

Z

ZOOM

Z

F

FOCUS

F

NO SHOW

FREEZE

AUTO PC ADJ.

AUTO COLOR.M

D

D.ZOOM

D

POWER ON-OFF BUTTON

Used to turn projector on or off. (P19)

POINT (VOLUME + / – )

BUTTONS

SELECT BUTTON

Used to select an item or adjust value in ON-SCREEN

MENU. They are also used to pan image in DIGITAL ZOOM

+/– mode. (P30)

POINT LEFT/RIGHT buttons are also used as VOLUME +/– buttons.

When pressing center of this button, it works as SELECT button.

SELECT BUTTON

Used to execute item selected. It is also used to expand / compress image in DIGITAL ZOOM mode.

(P30)

FREEZE BUTTON

Used to freeze picture.

(P21)

BEFORE OPERATION

KEYSTONE BUTTON

Used to correct keystone distortion.

(P20, 37)

LENS SHIFT

LENS

KEYSTONE

ON-OFF

KEYS

MENU SCREEN

E

M

O

V

SELECT

V

O

L

SCREEN BUTTON

Used to select screen.

(P30, 36)

Operating Range

Point Remote Control Unit toward projector (Receiver Window) whenever pressing any button.

Maximum operating range for

Remote Control Unit is about 16.4’

(5m) and 60° in front and rear of a projector.

ZOOM BUTTON

Used to adjust zoom.

(P20)

IMAGE BUTTON

Used to select image level. (P27, 33)

FOCUS BUTTON

Used to adjust focus.

(P20)

16.4’

(5 m)

60°

NO SHOW BUTTON

Used to turn picture into black image. (P21)

INPUT

INPUT

1

IMAGE

1

IMAGE

2

2 3 4

3

MUTE

Z

ZOOM

Z

F

FOCUS

F

NO SHOW

FREEZE

AUTO PC ADJ.

AUTO COLOR.M

D

D.ZOOM

D

D.ZOOM BUTTON

Used to select DIGITAL

ZOOM +/– mode and resize image. (P30)

COLOR MANAGEMENT

BUTTON

Used to operate COLOR

MANAGEMENT.

(P28, 34)

16.4’

(5 m)

WIRED REMOTE JACK

When using as Wired

Remote Control, connect

Remote Control Cable to this jack.

Battery installation is required when using as

Wired Remote Control.

60°

1

Remove battery compartment lid.

Pull up lid and remove it.

Remote Control Batteries Installation

2

Slide batteries into compartment.

Two AA size batteries

For correct polarity (+ and

–), be sure battery terminals are in contact with pins in compartment.

3

Replace compartment lid.

To insure safe operation, please observe following precautions :

Use (2) AA, UM3 or R06 type alkaline batteries.

Replace two batteries at same time.

Do not use a new battery with an used battery.

Avoid contact with water or liquid.

Do not expose Remote Control Unit to moisture, or heat.

Do not drop Remote Control Unit.

If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.

Danger of explosion if battery is incorrectly replaced.

Dispose of used batteries according to batteries manufacturers instructions and local rules.

Downloaded from ProjectorsManual.com Manuals

15

BEFORE OPERATION

TOP CONTROLS AND INDICATORS

This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.

LAMP REPLACE INDICATOR

Turns to yellow when life of projection lamp draws to an end. (P40)

WARNING TEMP. INDICATOR

Flashes red when internal projector temperature is too high. (P39)

READY INDICATOR

Lights green when a projector is ready to be turned on. And it flashes green in Power

Management mode.

(P37)

LAMP INDICATOR

Becomes dim when a projector is turned on.

And bright when a projector is in stand-by mode.

POWER ON–OFF BUTTON

Used to turn a projector on or off. (P19)

MENU BUTTON

Used to open or close

MENU operation. (P17,

18)

INPUT BUTTON

Used to select input source. (P22)

ZOOM BUTTON

Used to adjust zoom.

(P20)

FOCUS BUTTON

Used to adjust focus.

(P20)

LENS SHIFT BUTTON

Used to select LENS

SHIFT function. (P20)

POINT (VOLUME + / – ) BUTTONS

Used to select an item or adjust value in ON-SCREEN MENU. They are also used to pan image in

DIGITAL ZOOM

+/– mode. (P30)

POINT LEFT/RIGHT buttons are also used as VOLUME +/– buttons.

SELECT BUTTON

Used to execute item selected. It is also used to expand / compress image in DIGITAL

ZOOM mode. (P30)

IMAGE BUTTON

Used to select image level. (P27, 33)

AUTO PC ADJ. BUTTON

Used to operate AUTO PC

Adjustment function. (P23)

BEFORE OPERATION

OPERATING ON-SCREEN MENU

HOW TO OPERATE ON-SCREEN MENU

You can control and adjust this projector through ON-SCREEN

MENU. Refer to following pages to operate each adjustment on

ON-SCREEN MENU.

1 DISPLAY MENU

Press MENU button to display ON-SCREEN MENU.

WIRELESS REMOTE CONTROL

POINT BUTTON

Used to move Pointer

UP/ DOWN/ RIGHT/

LEFT.

2 MOVING POINTER

Move pointer (

✽ see below) or adjust value of item by pressing

POINT button(s) on Top Control or on Remote Control Unit.

SELECT BUTTON

Center of point button used to select item.

Pointer is icon on ON-SCREEN MENU to select item. See figures on section "FLOW OF ON-SCREEN MENU OPERATION" below.

3 SELECT ITEM

Select item or set selected function by pressing SELECT button.

TOP CONTROL

POINT BUTTONS

Used to move Pointer

UP/ DOWN/ RIGHT/

LEFT.

SELECT BUTTON

Used to select item.

FLOW OF ON-SCREEN MENU OPERATION

MENU BAR

Display ON-SCREEN MENU

1

Press MENU button to display ON-SCREEN MENU (MENU

BAR). A red frame is POINTER.

POINTER (red frame)

Press POINT DOWN button to move POINTER.

2

Select Menu to be adjusted

Move POINTER (red frame) to MENU ICON that you want to select by pressing POINT RIGHT / LEFT buttons.

ITEM

3

Control or adjust item through ON-SCREEN MENU

Press POINT DOWN button and move POINTER (red frame or red arrow) to ITEM that you want to adjust, and then press

SELECT button to show ITEM DATA.

4

Adjust ITEM DATA by pressing POINT RIGHT / LEFT buttons.

Refer to following pages for details of respective adjustments.

SELECT

BUTTON

32

32

Mid

32

32

32

MENU ICON

POINTER

(red frame)

ITEM DATA

Press POINT LEFT/RIGHT buttons to adjust value or set function.

Downloaded from ProjectorsManual.com Manuals

17

BEFORE OPERATION

MENU BAR

Press MENU BUTTON while connecting to PC input source.

FOR PC SOURCE

GUIDE WINDOW

Shows selected item of ON-

SCREEN MENU.

PC SYSTEM MENU

Used to select computer system.

(Refer to P22, 23)

IMAGE SELECT MENU

Used to select image level among

Standard, Real and Image 1 ~ 4.

(Refer to P27)

SCREEN MENU

Used to adjust size of image. [Normal

/ Full / True / Digital zoom +/–]

(Refer to P30)

SETTING MENU

Used to change settings of projector or reset Lamp

Replace Counter.

(Refer to P37, 38)

INPUT MENU

Used to select input source (Input

1, Input 2 or Input

3). (Refer to P22)

PC ADJUST MENU

Used to adjust parameters to match with input signal format.

(Refer to P23-25)

IMAGE ADJUST MENU

Used to adjust computer image.

[Contrast / Brightness

/ Color temp.

/ White Balance (R/G/B)

/ Color management

/ Auto picture control

/ Gamma]

(Refer to P28-29)

SOUND MENU

Used to adjust volume or mute sound.

(Refer to P21)

FOR VIDEO SOURCE

Press MENU BUTTON while connecting to VIDEO input source.

INPUT MENU

Used to select input source

(Input 1, Input 2 or Input 3).

(Refer to P31)

IMAGE SELECT MENU

Used to select image level among

Standard, Cinema and Image 1 ~ 4.

(Refer to P33)

SCREEN MENU

Used to set size of image to Full, Zoom,

Normal or Wide zoom.

(Refer to P36)

Same function as

Menu for PC source.

AV SYSTEM MENU

Used to select system of selected video source.

(Refer to P32)

IMAGE ADJUST MENU

Used to adjust picture image.

[Contrast / Brightness / Color

/ Tint / Color management

/ Auto picture control / Color temp.

/ White balance (R/G/B)

/ Sharpness / Gamma / Noise

Reduction / Progressive]

(Refer to P34-36)

Same function as

Menu for PC source.

BEFORE OPERATION

TURNING ON / OFF PROJECTOR

1

2

3

TURNING ON PROJECTOR

Complete peripheral connections (with Computer, VCR, etc.) before turning on projector. (Refer to "CONNECTING TO

PROJECTOR" on pages 11~13 for connecting that equipment.)

Connect a projector's AC Power Cord into an AC outlet. LAMP

Indicator lights RED, and READY Indicator lights GREEN.

NOTE : When “On start” function is ON, this projector is turned on automatically by connecting AC Power Cord to an

AC outlet. (Refer to pages 37, 38.)

Press POWER ON-OFF button on Top Control or on Remote

Control Unit to ON. LAMP Indicator dims, and Cooling Fans start to operate. Preparation Display appears on a screen and count-down starts. Signal from PC or Video source appears after

30 seconds.

Current Input position is also displayed on screen for 5 seconds.

Input 1

Input position

30

Preparation Display disappears after 30 seconds.

TURNING OFF PROJECTOR

1

2

Press POWER ON-OFF button on Top Control or on Remote

Control Unit, and a message "Power off?" appears on a screen.

Press POWER ON-OFF button again to turn off projector. LAMP

Indicator lights bright and READY Indicator turns off. After projector is turned off, Cooling Fans operate (for 90 seconds).

During this "Cooling Down" period, this appliance cannot be turned on.

3

When projector has cooled down, READY Indicator lights

GREEN again and you can turn projector on. After cooling down completely, disconnect AC Power Cord.

Power off?

Message disappears after 4 seconds.

TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN

PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE

TURNING IT OFF.

When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically.

Refer to “Power Management” on page 37.

When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on projector again.

When WARNING TEMP. Indicator continues to flash, follow procedures below:

1. Press POWER ON-OFF button to turn a projector off and disconnect AC Power Cord from an AC outlet.

2. Check Air Filters for dust accumulation.

3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 39.)

4. Turn a projector on again.

If WARNING TEMP. Indicator should still continue to flash, call Boxlight Corporation at 1-800-762-5757 or 360-779-7901.

Downloaded from ProjectorsManual.com Manuals

19

BASIC OPERATION

ADJUSTING SCREEN

ZOOM ADJUSTMENT

1

Press ZOOM button on Top Control or ZOOM

/

▼ button on

Remote Control Unit. Message “Zoom” is displayed.

2

Press ZOOM

▲ button or POINT UP button to make image larger, and press ZOOM

▼ button or POINT DOWN button to make image smaller.

Zoom

Message disappears after 4 seconds.

FOCUS ADJUSTMENT

1

Press FOCUS button on Top Control or FOCUS

/

▼ button on

Remote Control Unit. Message “Focus” is displayed.

2

Adjust focus of image by pressing FOCUS

/

▼ button or

POINT UP/DOWN button(s) .

Focus

NOTE;

Focus adjustment may not function properly if the image is corrected by KEYSTONE adjustment.

Message disappears after 4 seconds.

LENS SHIFT ADJUSTMENT

1

Press LENS SHIFT button on Top Control or on Remote Control

Unit. Message “Lens shift” is displayed.

2

Press POINT UP button to move image up, press POINT DOWN button to move image down.

Lens shift

KEYSTONE ADJUSTMENT

If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment.

1

Press KEYSTONE button on Remote Control Unit or select

Keystone on SETTING menu. (Refer to page 37.) Keystone dialog box appears.

2

Correct keystone distortion by pressing POINT

UP/DOWN/LEFT/RIGHT button(s). Press POINT UP button to reduce the upper part of the image, and press POINT DOWN button to reduce the lower part. Press POINT LEFT button to reduce the left part, and press POINT RIGHT button to reduce the right part.

• Arrows are white in no correction.

• Arrow(s) of direction being corrected turn(s) red.

• Arrow(s) disappear(s) at the maximum correction.

Reduce the upper width with POINT UP button.

Reduce the lower width with POINT DOWN button.

Reduce the left part with

POINT LEFT button.

Reduce the right part with

POINT RIGHT button.

BASIC OPERATION

PICTURE FREEZE FUNCTION

Press FREEZE button on Remote Control Unit to freeze picture on-screen. To cancel FREEZE function, press FREEZE button again or press any other button except POINT / SELECT button.

NO SHOW FUNCTION

Press NO SHOW button on Remote Control Unit to black out image.

To restore to normal, press NO SHOW button again or press any other button except POINT / SELECT button.

No show

Message disappears after 4 seconds.

SOUND ADJUSTMENT

DIRECT OPERATION

Volume

Press VOLUME (+/–) button(s) on Top Control or on Remote Control

Unit to adjust volume. Volume dialog box appears on screen for a few seconds.

(+) button to increase volume, and (–) button for decreasing.

Mute

Press MUTE button on Remote Control Unit to cut off sound. To restore sound to its previous level, press MUTE button again or press

Volume (+/–) button(s).

Indicates roughly level of volume.

Press MUTE button to set

Mute function On or Off.

Display disappears after 4 seconds.

1

2

MENU OPERATION

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT buttons to move a red frame pointer to

SOUND Menu icon.

Press POINT DOWN button to move a red frame pointer to item that you want to select, and then press SELECT button.

Volume

To increase volume, press POINT RIGHT button, and press POINT

LEFT button for decreasing.

Mute

Press POINT LEFT/RIGHT button(s) to cut off sound. Dialog box display is changed to “On” and sound is cut off. To restore sound to its previous level, press POINT LEFT/RIGHT button(s) again.

SOUND MENU

Close SOUND Menu.

Indicates roughly level of volume.

SOUND Menu icon

Downloaded from ProjectorsManual.com Manuals

21

COMPUTER INPUT

SELECTING INPUT SOURCE

DIRECT OPERATION

Choose Input by pressing INPUT button on Top Control.

Choose Input by pressing INPUT, INPUT 1, INPUT 2 or INPUT 3 button on Remote Control Unit.

If projector cannot reproduce proper image, select correct input source through MENU OPERATION (see below).

INPUT button

INPUT 1

INPUT 2

INPUT 3

1

MENU OPERATION

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT buttons to select Input and press SELECT button. Another dialog box INPUT SELECT Menu will appear.

INPUT Menu icon

2

Press POINT DOWN button and a red-arrow icon will appear.

Move arrow to INPUT source that you want to select, and then press SELECT button.

SELECTING COMPUTER SYSTEM

WHEN SELECT INPUT 1 (COMPUTER INPUT TERMINALS )

INPUT MENU

1

2

3

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to

INPUT Menu icon.

Press POINT DOWN button to move a red arrow pointer to Input

1 and then press SELECT button. Source Select Menu will appear.

Move a pointer to either Digital or Analog and then press

SELECT button.

Digital

Analog

When your computer is connected to COMPUTER

INPUT (DIGITAL) terminal, select RGB (Digital).

When your computer is connected to COMPUTER INPUT

(ANALOG) terminal, select RGB (Analog).

Input 1

INPUT Menu icon

Move a pointer (red arrow) to

Input 1 and press SELECT button.

Source Select Menu

Move a pointer to Digital or

Analog and press SELECT button.

WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )

When connect a computer output [5 BNC Type (Green, Blue, Red,

Horiz. Sync and Vert. Sync.)] from a computer to G, B, R, H/HV and V jacks.

INPUT MENU

INPUT Menu icon

1

2

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to

INPUT Menu icon.

Press POINT DOWN button to move a red arrow pointer to Input

2 and then press SELECT button. Source Select Menu will appear.

Input 2

Move a pointer (red arrow) to

Input 2 and press SELECT button.

3

Press POINT DOWN button and a red-arrow icon will appear.

Move arrow to "RGB", and then press SELECT button.

Source Select Menu

Move a pointer to RGB and press SELECT button.

COMPUTER INPUT

AUTOMATIC MULTI-SCAN SYSTEM

This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to

“COMPATIBLE COMPUTER SPECIFICATION” on page 26). When selecting Computer, this projector automatically tunes to incoming signal and projects proper image without any special setting. (Some computers need setting manually.)

Note : Projector may display one of following messages.

Auto

––––

When projector cannot recognize connected signal as PC system provided in this projector, Auto PC Adjustment function operates to adjust projector and message “Auto” is displayed on SYSTEM Menu icon.

When image is not provided properly, manual adjustment is required. (Refer to P24 and 25.)

There is no signal input from computer. Make sure connection of computer and a projector is set correctly.

(Refer to TROUBLESHOOTING on page 42.)

PC SYSTEM MENU

PC SYSTEM Menu icon

Displays system being selected.

D-VGA, D-SVGA or D-XGA

When digital computer signal is received on DVI terminal, above message is displayed on PC SYSTEM Menu icon.

PC SYSTEM MENU

SELECT COMPUTER SYSTEM MANUALLY

This projector automatically selects PC system among those provided in this projector and PC system can be also selected manually.

1

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT buttons to move a red frame pointer to PC

SYSTEM Menu icon.

2

Press POINT DOWN button to move a red arrow pointer to system that you want to set, and then press SELECT button.

PC SYSTEM Menu icon

Displays system being selected.

Systems on this dialog box can be selected.

Custom Mode (1~5) set in PC

ADJUST Menu. (P24, 25)

PC ADJUSTMENT

AUTO PC ADJUSTMENT

Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your computer. Auto PC Adjustment function can be operated as follows.

1

Auto PC Adj.

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to PC

ADJUST Menu icon.

PC ADJUST MENU

2

Press POINT DOWN button to move a red frame pointer to

AUTO PC Adj. icon and then press SELECT button twice.

This Auto PC Adjustment can be also executed by pressing

AUTO PC ADJ. button on Top Control or on Remote Control

Unit.

PC ADJUST Menu icon

Store adjustment parameters.

Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, setting can be done just by selecting Mode in PC SYSTEM Menu (P23). Refer to step 3 of MANUAL PC ADJUSTMENT section (P25).

Move a red frame pointer to AUTO PC

Adj. icon and press SELECT button.

NOTE

Fine sync, Total dots and Picture Position of some computers can not be fully adjusted with this Auto PC Adjustment function. When image is not provided properly through this function, manual adjustments are required. (Refer to page 24,

25.)

Auto PC Adjustment function cannot be operated in Digital Signal input on DVI terminal and “RGB”, “720p (HDTV)”,

“1035i (HDTV)” or “1080i (HDTV)” is selected on PC SYSTEM Menu.

Downloaded from ProjectorsManual.com Manuals

23

COMPUTER INPUT

MANUAL PC ADJUSTMENT

This projector can automatically tune to display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system of this projector. If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.

This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This enables you to recall setting for a specific computer whenever you use it.

Note : This PC ADJUST Menu cannot be operated when in digital signal input on DVI terminal and “RGB” is selected on PC

SYSTEM MENU (P23).

1

2

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to PC

ADJUST Menu icon.

Press POINT DOWN button to move a red frame pointer to item that you want to adjust and then press SELECT button.

Adjustment dialog box will appear. Press POINT LEFT/RIGHT button to adjust value.

Fine sync

Adjusts an image as necessary to eliminate flicker from display.

Press POINT LEFT/RIGHT button to adjust value.(From 0 to 31.)

PC ADJUST MENU

PC ADJUST Menu icon

Move a red frame icon to item and press

SELECT button.

Total dots

Number of total dots in one horizontal period. Press POINT

LEFT/RIGHT button(s) and adjust number to match your PC image.

Selected Mode

Shows status

(Stored / Free) of selected Mode.

Horizontal

Adjusts horizontal picture position. Press POINT LEFT/RIGHT button(s) to adjust position.

Press POINT LEFT/RIGHT button to adjust value.

Vertical

Adjusts vertical picture position. Press POINT LEFT/RIGHT button(s) to adjust position.

Current mode

Press SELECT button to show information of computer selected.

Clamp

Adjusts clamp position. When image has a dark bar(s), try this adjustment.

Press SELECT button at this icon to adjust “Clamp,” “Display area (H/V)” or set “Full screen.”

Current mode

Press SELECT button at

Current mode icon to show information of computer connected.

COMPUTER INPUT

Display area

Selects area displayed with this projector. Select resolution at

Display area dialog box.

Display area H

Adjustment of horizontal area displayed with this projector. Press

POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button.

Display area V

Adjustment of vertical area displayed with this projector. Press

POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button.

Full screen

Press POINT LEFT/RIGHT button(s) to switch Full screen function to

“On” or “Off.” Set “On” to resize image to fit the horizontal size of the screen.

NOTE : Display area (H/V) and Full screen cannot be adjusted when

“1035i (HDTV)” or “1080i (HDTV)” is selected on PC

SYSTEM Menu (P23).

Press SELECT button at

Display area icon and Display area dialog box appears.

Press POINT LEFT

/RIGHT button(s) to adjust value and then press SELECT button.

Display area

To store adjustment data.

This Mode has parameters being stored.

3

Store

To store adjustment parameters, move a red frame pointer to

Store icon and then press SELECT button. Move a red arrow pointer to any of Mode 1 to 5 that you want to store and then press SELECT button.

Mode free

To clear adjustment parameters previously set, move a red frame pointer to Mode free icon and then SELECT button. Move a red arrow pointer to Mode that you want to clear and then press SELECT button.

Other icons operates as follows.

Reset

Reset all adjust parameters on adjustment dialog box to previous figure.

Quit

Closes PC ADJUST MENU.

Vacant Mode

Store icon

Shows values of “Total dots,”

“Horizontal,” “Vertical,” “Display area H,” and “Display area V.”

To clear adjustment data.

Downloaded from ProjectorsManual.com Manuals

Mode free icon

Close this dialog box.

25

COMPUTER INPUT

COMPATIBLE COMPUTER SPECIFICATIONS

Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less than 140 MHz of Dot Clock.

ON-SCREEN

DISPLAY

VGA 1

VGA 2

VGA 3

VGA 4

VGA 5

VGA 6

VGA 7

RESOLUTION

640 x 480

720 x 400

640 x 400

640 x 480

640 x 480

640 x 480

640 x 480

MAC LC13 640 x 480

MAC 13

RGB

RGB

SVGA 1

640 x 480

––––––––

(Interlace)

––––––––

(Interlace)

800 x 600

SVGA 2 800 x 600

SVGA 3

SVGA 4

SVGA 5

SVGA 6

SVGA 7

800 x 600

800 x 600

800 x 600

800 x 600

800 x 600

SVGA 8

SVGA 9

800 x 600

800 x 600

SVGA 10 800 x 600

SVGA 11 800 x 600

MAC 16 832 x 624

XGA 1

XGA 2

XGA 3

XGA 4

XGA 5

XGA 6

XGA 7

XGA 8

XGA 9

1024 x 768

1024 x 768

1024 x 768

1024 x 768

1024 x 768

1024 x 768

1024 x 768

1024 x 768

1024 x 768

(Interlace)

46.875

53.674

48.08

37.90

34.50

38.00

38.60

32.70

38.00

49.72

H-Freq.

(kHz)

31.47

31.47

31.47

37.86

37.86

37.50

43.269

34.97

35.00

15.734

15.625

35.156

37.88

48.36

68.677

60.023

56.47

60.31

48.50

44.00

63.48

36.00

75.00

85.06

72.19

61.03

55.38

60.51

60.31

51.09

60.51

74.55

V-Freq.

(Hz)

59.88

70.09

70.09

74.38

72.81

75.00

85.00

66.60

66.67

30

25

56.25

60.32

60.00

84.997

75.03

70.07

74.92

60.02

54.58

79.35

43.59

ON-SCREEN

DISPLAY

XGA 10

XGA 11

XGA 12

XGA 13

XGA 14

XGA15

MAC 19

MAC 21

RESOLUTION

1024 x 768

1024 x 768

1024 x 768

(Interlace)

1024 x 768

1024 x 768

1024 x 768

1024 x 768

1152 x 870

SXGA 1 1152 x 864

SXGA 2 1280 x 1024

SXGA 3 1280 x 1024

SXGA 4 1280 x 1024

SXGA 5 1280 x 1024

SXGA 6 1280 x 1024

SXGA 7 1280 x 1024

SXGA 8 1280 x 1024

SXGA 9 1280 x 1024

SXGA 10 1280 x 960

SXGA 11 1152 x 900

SXGA 12 1152 x 900

SXGA 13

SXGA 14

1280 x 1024

(Interlace)

1280 x 1024

(Interlace)

SXGA 15 1280 x 1024

SXGA 16 1280 x 1024

SXGA 17 1152 x 900

SXGA 18

1280 x 1024

(Interlace)

SXGA 19 1280 x 1024

MAC

MAC

720p (HDTV)

1035i (HDTV)

1080i (HDTV)

1280 x 960

1280 x 1024

––––––––

(Progressive)

––––––––

(Interlace)

––––––––

(Interlace)

H-Freq.

(kHz)

62.04

61.00

35.522

46.90

47.00

58.03

60.24

68.68

64.20

62.50

63.90

63.34

63.74

71.69

81.13

63.98

79.976

60.00

61.20

71.40

50.00

50.00

63.37

76.97

61.85

46.43

63.79

75.00

80.00

45.00

33.75

33.75

V-Freq.

(Hz)

77.07

75.70

43.48

58.20

58.30

72.0

75.08

75.06

70.40

58.60

60.00

59.98

60.01

67.19

76.107

60.02

75.025

60.00

65.20

75.60

43.00

47.00

60.01

72.00

66.00

43.35

60.18

75.08

75.08

60.00

30.00

30.00

When a input signal is digital from DVI terminal, refer to chart below.

ON-SCREEN

DISPLAY

D-VGA

D-SVGA

RESOLUTION

640 x 480

800 x 600

H-Freq.

(kHz)

31.469

37.879

V-Freq.

(Hz)

59.940

60.317

NOTE : Specifications are subject to change without notice.

ON-SCREEN

DISPLAY

D-XGA

RESOLUTION

1024 x 768

H-Freq.

(kHz)

48.363

V-Freq.

(Hz)

60.004

COMPUTER INPUT

PICTURE IMAGE ADJUSTMENTS

IMAGE LEVEL SELECT (DIRECT)

Select image level among Standard, Real, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE button on Top Control or on Remote

Control Unit.

Select Image 1-4 by pressing IMAGE 1-4 buttons on Remote Control

Unit.

IMAGE button

Standard

Real

Image 1

Standard

Normal picture level preset on this projector.

Real

Picture level with improved halftone for graphics.

IMAGE 1~4

User preset picture adjustment in IMAGE ADJUST Menu (P28-29).

Image 2

Image 3

Image 4

IMAGE LEVEL SELECT (MENU)

IMAGE SELECT MENU

1

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to

IMAGE SELECT Menu icon.

2

Press POINT DOWN button to move a red frame pointer to level that you want to set and then press SELECT button.

Standard

Normal picture level preset on this projector.

Real

Picture level with improved halftone for graphics.

IMAGE 1~4

User preset picture adjustment in IMAGE ADJUST Menu (P28-29).

IMAGE SELECT

Menu icon

Move a red frame icon to level and press SELECT button.

Level being selected.

Downloaded from ProjectorsManual.com Manuals

27

COMPUTER INPUT

1

IMAGE LEVEL ADJUSTMENT

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT buttons to move a red frame pointer to

IMAGE ADJUST Menu icon.

IMAGE ADJUST MENU

2

Press POINT DOWN button to move a red frame pointer to item that you want to adjust and then press SELECT button. Level of each item is displayed. Adjust each level by pressing POINT

LEFT/RIGHT button(s).

Move a red frame pointer to item to be selected and then press SELECT button.

Contrast

Press POINT LEFT button to decrease contrast, and POINT RIGHT button to increase contrast. (From 0 to 63.)

Brightness

Press POINT LEFT button to adjust image darker, and POINT

RIGHT button to adjust brighter. (From 0 to 63.)

IMAGE ADJUST

Menu icon

Selected Image level

Color temp.

Press either POINT LEFT button or POINT RIGHT button to Color temp. level that you want to select. (XLow, Low, Mid or High)

White balance (Red)

Press POINT LEFT button to lighten red tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

White balance (Green)

Press POINT LEFT button to lighten green tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

White balance (Blue)

Press POINT LEFT button to lighten blue tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

Color Management

The Color management function can be used to adjust the level, phase and gamma of the selected display colors on the screen, and to replace these colors with other colors if required.

The projector lets you replace up to eight colors for each image.

There are four preset images for VIDEO mode and four preset images for PC, giving a total of eight images.

1

Press the POINT DOWN button to move the red frame pointer to

"COLOR MANAGEMENT", and then press the SELECT button.

The COLOR MANAGEMENT menu will appear and pointer mode will be enabled. The image that was being projected when the button was pressed will be paused, and the COLOR MAN-

AGEMENT POINTER will appear.

2

Use the POINT buttons to move the pointer to a section of the paused image that contains the color that you would like to adjust, and then press the SELECT button. The mode will change to COLOR SELECTION mode, and the color in the center of the pointer will be selected and adjustment will be possible.

3

Use the POINT buttons to adjust the level and phase of the color, and then press the SELECT button to confirm the setting.

Next, use the POINT buttons to adjust the gamma correction for the color, and then press the SELECT button to accept the setting. When the SELECT button is pressed, the mode will change to LIST mode.

32

32

Mid

32

32

32

L1

8

POINTER MODE

Press POINT LEFT/RIGHT buttons to adjust value.

Store icon

Press SELECT button at this icon to store adjustment.

COLOR

MANAGEMENT

POINTER

NOTE;

Press the COLOR M. button on the remote control to display the COLOR MANAGEMENT menu.

If you would like to check or re-adjust a color management setting that has already been made, press the COLOR M. button on the remote control once more to change to LIST mode.

VIDEO INPUT

4

To move the red frame pointer to "MENU", and then press the

SELECT button. The message "OK"? is displayed. Move the pointer to [Yes] and then press SELECT button. The COLOR

MANAGEMENT menu will be exited and the display will return to the IMAGE ADJUST menu. (At this time, the image will stop being paused and normal projection will resume.) After changing the COLOR MANAGEMENT settings, use the IMAGE

ADJUST menu to store the changed settings.

COLOR SELECTION MODE

CANCEL

The mode will return to the pointer mode (even if you press the

MENU key on the projector or the remote control). (You will need to reselect and re-adjust the color in this case.)

QUIT

The COLOR MANAGEMENT menu will be exited and the display will return to the normal projection screen, but any settings that have been changed will not be stored. To store the changed settings, be sure to select "LIST" using the POINT buttons and change to the next mode (LIST mode).

LIST MODE

COLOR SELECTION

MODE

Level and phase adjustment palette.

LIST

LIST MODE

Gamma adjustment palette.

CANCEL QUIT

COLOR PALETTE

DEL

The check mark will be cleared and the effect of the setting adjustment for that line on the projected images will be momentarily canceled.

COLOR PALETTE

The mode will return to COLOR SELECTION mode so that you can re-adjust the setting for the color in that line. This option is not available if the check mark has been cleared by the operation immediately above.)

DEL

The setting adjustment for the color in that line will be canceled.

ALL DEL

The setting adjustment for the colors in all lines will be canceled.

COLOR M.

The mode will return to POINTER mode.

Auto picture control

Press either POINT LEFT button or POINT RIGHT button to Auto picture control position that you want to select . (Off, L1 or L2)

Off ······· Auto picture control OFF position.

L1 ········ Auto picture control LEVEL 1 position.

L2 ········ Auto picture control LEVEL 2 position.

Gamma

Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast. (From 0 to 15.)

Store

To store manually preset image, move a red frame pointer to Store icon and press SELECT button. Image Level Menu will appear.

Move a red frame pointer to Image 1 to 4 where you want to set and then press SELECT button.

Other icons operates as follows.

Reset

Reset all adjustment to previous figure.

Quit

Closes IMAGE MENU.

Downloaded from ProjectorsManual.com Manuals

ALL DEL MENU COLOR M.

NOTE;

If you press the COLOR M. button on the remote control, the COLOR MANAGEMENT menu will be exited and the display will return to the normal projection screen, but any settings that have been changed will not be stored. To store the changed settings, be sure to select "MENU" using the

POINT buttons and store the settings.

32

32

Mid

32

32

32

L1

8

Image Level Menu

Move a red frame pointer to any of Image 1 to 4 where you want to set and then press SELECT button.

29

COMPUTER INPUT

PICTURE SCREEN ADJUSTMENT

This projector has a picture screen resize function, which enables you to display desirable image size.

PICTURE SCREEN SELECT (DIRECT)

Select picture screen among Normal, Full, True, Digital zoom + and

Digital zoom - by pressing SCREEN button on Remote Control Unit.

SCREEN button

Normal

Full

True

Digital zoom +

Digital zoom -

1

2

PICTURE SCREEN SELECT (MENU)

SCREEN MENU

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button(s) to move a red frame pointer to

SCREEN Menu icon.

Press POINT DOWN button and move a red frame pointer to function that you want to select and then press SELECT button.

SCREEN Menu icon

Move red frame to function and press

SELECT button.

Normal

Provides image to fit the panel size of the screen.

Full

Provides image to fit the horizontal size of the screen.

True

Provides image in its original size. When the original image size is larger than screen size (1366 x 768), this projector enters “Digital

Zoom +” mode automatically.

Digital zoom +

When Digital zoom + is selected, ON-SCREEN MENU disappears and message “D. Zoom +” is displayed. Press SELECT button to expand image size. And press POINT UP/DOWN/LEFT/RIGHT button(s) to pan image. Panning function can work only when image is larger than screen size.

A projected image can be also expanded by pressing D.ZOOM

▲ button on Remote Control Unit.

NOTE

True and Digital zoom +/– cannot be operated when “RGB”, “1035i (HDTV)” or “1080i (HDTV)” is selected on PC SYSTEM Menu (P23).

Full cannot be selected when “720p (HDTV)”,

“1035i (HDTV)” or “1080i (HDTV)” is selected on

PC SYSTEM Menu (P23).

This projector cannot display any resolution higher than 1280 X 1024. If your computer’s screen resolution is higher than 1280 X 1024, reset resolution to lower before connecting projector.

Image data in other than XGA (1024 x 768) is modified to fit screen size in initial mode.

Panning function may not operate properly if computer system prepared on PC ADJUST Menu is used.

Digital Zoom –

When Digital zoom – is selected, ON-SCREEN MENU disappears and message “D. Zoom –” is displayed. Press SELECT button to compress image size.

A projected image can be also compressed by pressing D.ZOOM

▼ button on Remote Control Unit.

To cancel Digital Zoom +/– mode, press any button except D.ZOOM

/

, SELECT, POINT and AUTO PC ADJ. buttons.

VIDEO INPUT

SELECTING INPUT SOURCE

WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )

When connecting to those equipment, select a type of Video source in SOURCE SELECT Menu.

INPUT MENU

1

2

3

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to

INPUT Menu icon.

Press POINT DOWN button to move a red arrow pointer to Input

2 and then press SELECT button. Source Select Menu will appear.

Move a pointer to source that you want to select and then press

SELECT button.

Input 2

INPUT Menu icon

Move a pointer (red arrow) to

Input 2 and press SELECT button.

Source Select Menu

Move a pointer to Video or

Y, Pb/Cb, Pr/Cr and press

SELECT button.

Video

When video input signal is connected to VIDEO jack, select Video.

Y,Pb/Cb,Pr/Cr

When video input signal is connected to Y-Pb/Cb-

Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.

WHEN SELECT INPUT 3 (AV TERMINALS )

INPUT MENU

When connecting to those equipment, select a type of Video source in SOURCE SELECT (VIDEO) Menu.

1

2

3

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to

INPUT Menu icon.

Press POINT DOWN button to move a red arrow pointer to Input

3 and then press SELECT button. Source Select Menu will appear.

Move a pointer to source that you want to select and then press

SELECT button.

Input 3

INPUT Menu icon

Move a pointer (red arrow) to

Input 3 and press SELECT button.

Source Select Menu (VIDEO)

Move a pointer to source and press SELECT button.

Video

When video input signal is connected to VIDEO jack, select Video.

Y,Pb/Cb,Pr/Cr

S-Video

When video input signal is connected to Y-Pb/Cb-

Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.

When video input signal is connected to S-VIDEO jack, select S-Video.

Downloaded from ProjectorsManual.com Manuals

31

VIDEO INPUT

1

2

SELECTING VIDEO SYSTEM

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT buttons to move a red frame pointer to AV

SYSTEM Menu icon.

Press POINT DOWN button to move a red arrow pointer to system that you want to select and then press SELECT button.

VIDEO JACK OR S-VIDEO JACK

Auto

Projector automatically detects incoming Video system, and adjusts itself to optimize its performance.

When Video System is PAL-M or PAL-N, select system manually first.

PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N

If projector cannot reproduce proper video image, it is necessary to select a specific broadcast signal format among PAL, SECAM, NTSC,

NTSC 4.43, PAL-M, and PAL-N.

AV SYSTEM MENU (VIDEO OR S-VIDEO)

AV SYSTEM Menu icon

This box indicates system being selected.

Move pointer to system and press SELECT button.

Y, Pb/Cb, Pr/Cr JACKS

Auto

Projector automatically detects incoming Video signal, and adjusts itself to optimize its performance.

When Video System is 1035i or 1080i, select system manually first.

AV SYSTEM MENU (COMPONENT VIDEO)

COMPONENT VIDEO SIGNAL FORMAT

If projector cannot reproduce proper video image, it is necessary to select a specific component video signal format among 480i, 575i,

480p, 575p, 720p, 1035i and 1080i.

AV SYSTEM Menu icon

This box indicates system being selected.

Move pointer to system and press SELECT button.

VIDEO INPUT

PICTURE IMAGE ADJUSTMENTS

IMAGE LEVEL SELECT (DIRECT)

Select image level among Standard, Cinema, Image 1, Image 2,

Image 3 and Image 4 by pressing IMAGE button on Top Control or on

Remote Control Unit.

Select Image 1-4 by pressing IMAGE 1-4 buttons on Remote Control

Unit.

Standard

Normal picture level preset on this projector.

Cinema

Picture level adjusted for picture with fine tone.

IMAGE 1~4

User preset picture adjustment in IMAGE ADJUST Menu (P34-36).

IMAGE button

Standard

Cinema

Image 1

Image 2

Image 3

Image 4

1

2

IMAGE LEVEL SELECT (MENU)

IMAGE SELECT MENU

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button to move a red frame pointer to

IMAGE SELECT Menu icon.

Press POINT DOWN button to move a red frame pointer to level that you want to set and then press SELECT button.

Standard

Normal picture level preset on this projector.

Cinema

Picture level adjusted for picture with fine tone.

IMAGE 1~4

User preset picture adjustment in IMAGE ADJUST Menu (P34-36).

Level being selected.

IMAGE SELECT

Menu icon

Move red frame pointer to level and press SELECT button.

Downloaded from ProjectorsManual.com Manuals

33

VIDEO INPUT

1

IMAGE LEVEL ADJUSTMENT

Press MENU button and ON-SCREEN MENU will appear.

Press POINT LEFT/RIGHT button(s) to move a red frame pointer to IMAGE ADJUST Menu icon.

IMAGE ADJUST MENU

2

Press POINT DOWN button to move a red frame pointer to item that you want to adjust and then press SELECT button.

Level of each item is displayed. Adjust each level by pressing

POINT LEFT/RIGHT button(s).

Move a red frame pointer to item to be selected and then press SELECT button.

Contrast

Press POINT LEFT button to decrease contrast, and POINT RIGHT button to increase contrast. (From 0 to 63.)

Brightness

Press POINT LEFT button to adjust image darker, and POINT

RIGHT button to adjust brighter. (From 0 to 63.)

Color

Press POINT LEFT button to lighten color, and POINT RIGHT button to deeper color. (From 0 to 63.)

Tint

Press POINT LEFT button or POINT RIGHT button to obtain proper color. (From 0 to 63.)

Color Management

The Color management function can be used to adjust the level, phase and gamma of the selected display colors on the screen, and to replace these colors with other colors if required.

The projector lets you replace up to eight colors for each image.

There are four preset images for VIDEO mode and four preset images for PC, giving a total of eight images.

1

Press the POINT DOWN button to move the red frame pointer to

"COLOR MANAGEMENT", and then press the SELECT button.

The COLOR MANAGEMENT menu will appear and pointer mode will be enabled. The image that was being projected when the button was pressed will be paused, and the COLOR MAN-

AGEMENT POINTER will appear.

2

Use the POINT buttons to move the pointer to a section of the paused image that contains the color that you would like to adjust, and then press the SELECT button. The mode will change to COLOR SELECTION mode, and the color in the center of the pointer will be selected and adjustment will be possible.

3

4

Use the POINT buttons to adjust the level and phase of the color, and then press the SELECT button to confirm the setting.

Next, use the POINT buttons to adjust the gamma correction for the color, and then press the SELECT button to accept the setting. When the SELECT button is pressed, the mode will change to LIST mode.

To move the red frame pointer to "MENU", and then press the

SELECT button. The message "OK"? is displayed. Move the pointer to [Yes] and then press SELECT button. The COLOR

MANAGEMENT menu will be exited and the display will return to the IMAGE ADJUST menu. (At this time, the image will stop being paused and normal projection will resume.) After changing the COLOR MANAGEMENT settings, use the IMAGE

ADJUST menu to store the changed settings.

COLOR SELECTION MODE

CANCEL

The mode will return to the pointer mode (even if you press the

MENU key on the projector or the remote control). (You will need to reselect and re-adjust the color in this case.)

32

32

32

32

L1

POINTER MODE

COLOR

MANAGEMENT

POINTER

NOTE;

Press the COLOR M. button on the remote control to display the COLOR MANAGEMENT menu.

If you would like to check or re-adjust a color management setting that has already been made, press the COLOR M. button on the remote control once more to change to LIST mode.

COLOR SELECTION

MODE

Level and phase adjustment palette.

Gamma adjustment palette.

LIST

IMAGE ADJUST

Menu icon

Press POINT LEFT/RIGHT buttons to adjust value.

Press SELECT button at this icon to display other items.

CANCEL

QUIT

VIDEO INPUT

QUIT

The COLOR MANAGEMENT menu will be exited and the display will return to the normal projection screen, but any settings that have been changed will not be stored. To store the changed settings, be sure to select "LIST" using the POINT buttons and change to the next mode (LIST mode).

LIST MODE

LIST MODE

COLOR PALETTE

DEL

The check mark will be cleared and the effect of the setting adjustment for that line on the projected images will be momentarily canceled.

COLOR PALETTE

The mode will return to COLOR SELECTION mode so that you can re-adjust the setting for the color in that line. This option is not available if the check mark has been cleared by the operation immediately above.)

DEL

The setting adjustment for the color in that line will be canceled.

ALL DEL

The setting adjustment for the colors in all lines will be canceled.

COLOR M.

The mode will return to POINTER mode.

Auto picture control

Press either POINT LEFT button or POINT RIGHT button to Auto picture control position that you want to select . (Off, L1 or L2)

Off ······· Auto picture control OFF position.

L1 ········ Auto picture control LEVEL 1 position.

L2 ········ Auto picture control LEVEL 2 position.

Color temp.

Press either POINT LEFT button or POINT RIGHT button to Color temp. level that you want to select. (XLow, Low, Mid or High)

White balance (Red)

Press POINT LEFT button to lighten red tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

White balance (Green)

Press POINT LEFT button to lighten green tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

White balance (Blue)

Press POINT LEFT button to lighten blue tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

Sharpness

Press POINT LEFT button to soften image, and POINT RIGHT button to sharpen image. (From 0 to 15.)

Gamma

Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast. (From 0 to 15.)

Noise reduction

Press POINT LEFT/RIGHT button(s) to change noise reduction mode. Dialog box display is changed to “On” to reduce noise (rough parts) of image. Press POINT LEFT/RIGHT button(s) again, to change noise reduction mode to off.

Downloaded from ProjectorsManual.com Manuals

ALL DEL MENU COLOR M.

NOTE;

If you press the COLOR M. button on the remote control, the COLOR MANAGEMENT menu will be exited and the display will return to the normal projection screen, but any settings that have been changed will not be stored. To store the changed settings, be sure to select "MENU" using the

POINT buttons and store the settings.

Press SELECT button at this icon to display previous items.

Mid

32

32

32

15

8

On

On

Press POINT LEFT/RIGHT buttons to adjust value.

Press SELECT button at this icon to store value.

Progressive scan

Press POINT LEFT/RIGHT button(s) to change progressive scan mode. Dialog box display is changed to “Off” and progressive scan mode to off.

Press POINT LEFT/RIGHT button(s) again, progressive scan mode to on.

NOTE :

Tint cannot be adjusted when video system is PAL,

SECAM, PAL-M or PAL-N.

Progressive cannot be operated when “480p”,

“575p” or “720p” is selected on AV SYSTEM MENU

(P32).

35

VIDEO INPUT

Store

To store adjustment data, move a red frame pointer to Store icon and press SELECT button. Image Level Menu will appear. Move a red frame pointer to Image Level 1 to 4 and then press SELECT button.

Other icons operates as follows.

Reset

Reset all adjustment to previous figure.

Quit

Closes IMAGE MENU.

Mid

32

32

32

15

8

On

On

Image Level Menu

Move a red frame pointer to image icon to be set and then press SELECT button.

Store icon

PICTURE SCREEN ADJUSTMENT

PICTURE SCREEN SELECT (DIRECT)

Select picture screen among Full, Zoom, Normal and Wide zoom by pressing SCREEN button on Remote Control Unit.

SCREEN button

Full

Zoom

Normal

Wide zoom

PICTURE SCREEN SELECT (MENU)

This projector has a picture screen resize function, which enables you to display desirable image size.

1

2

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button(s) to move a red frame pointer to

SCREEN Menu icon.

Press POINT DOWN button and move a red frame pointer to function that you want to select and then press SELECT button.

SCREEN MENU

SCREEN Menu icon

Full

Provides image to fit width of screen by expanding image width uniformly. This function can be used for providing a squeezed video signal at wide video aspect ratio of 16 : 9.

When your video equipment (such as DVD) has 16 : 9 output mode, select 16 : 9 and select Full on this SCREEN Menu to provide better quality.

Move the red frame to the function and press SELECT button.

NOTE : SCREEN Menu cannot be operated when

“720p,” “1035i,” or “1080i” is selected on AV

SYSTEM Menu (P32).

Zoom

Provides image to fit screen size (16 : 9 aspect ratio) by expanding image width and height uniformly. This function can be used for providing a letter box mode picture (4 : 3 aspect picture with black bar on top and bottom edges) at wide video aspect of 16 : 9.

Normal

Provides image at the normal video aspect ratio of 4 : 3.

Wide zoom

Provides image to fit width of screen by expanding both sides of image. This function is suitable to provide a normal video signal (4 :

3 aspect ratio) at wide video aspect ratio of 16 : 9.

SETTING

SETTING MENU

1

2

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT button(s) to move a red-frame pointer to

SETTING icon.

Press POINT DOWN button to move a red-frame pointer to item that you want to set and then press SELECT button. Setting dialog box appears.

Language

Language used in ON-SCREEN MENU is selectable from among

English, German, French, Italian, Spanish, Portuguese, Dutch,

Swedish, Chinese, Korean and Japanese.

Keystone

When image is distorted, select Keystone. ON-SCREEN MENU disappears and Keystone dialog box is displayed. Correct keystone distortion by pressing POINT UP/DOWN/LEFT/RIGHT button(s).

Refer to KEYSTONE ADJUSTMENT on page 20.

Blue back

When this function is “On,” this projector will produce a blue image instead of video noise on screen when any input source is unplugged or turned off.

Display

This function decides whether to display On-Screen Displays.

On ··· shows all On-Screen Displays.

Off ···· sets On-Screen Displays disappeared except;

ON-SCREEN MENU

“Power off?” message

Logo

When this function is “On,” projector displays our logo when starting up.

SETTING MENU

Set a red frame pointer to item and press SELECT button.

SETTING Menu icon

When pressing SELECT button at Language,

Language Menu appears.

Move a pointer to item and then press POINT

LEFT/RIGHT button(s).

Ceiling

When this function is “On,” picture is top / bottom and left / right reversed. This function is used to project image from a ceiling mounted projector.

Rear

When this function is “On,” picture is left / right reversed. This function is used to project image to a rear projection screen.

Ceiling function

Power management

This function turns Projection Lamp off when this projector detects signal interruption and is not used for a certain period in order to reduce power consumption and maintain Lamp-life. (This projector is shipped with this function ON.)

Power Management function operates to turn Projection Lamp off when input signal is interrupted and any button is not pressed over 5 minutes. This function operates as follows;

1. When any input signal is interrupted, “No signal” and counting down display appears (for 5 minutes).

2. After counting down for 5 minutes, projector lamp and READY indicator are turned off.

3. When READY indicator flashing, Projection Lamp can be turned on again (Power Management mode).

In this Power Management mode, Projection Lamp is automatically turned on when input signal connected or projector is operated with any button on Top Control or on Remote Control

Unit again.

Rear function

Time left until Lamp off.

Downloaded from ProjectorsManual.com Manuals

37

SETTING

On start

When this function is “On,” projector is automatically turned on just by connecting AC Power cord to a wall outlet.

Note ; Be sure to turn projector off properly (refer to section

“TURNING OFF PROJECTOR” on P19). If projector is turned off in wrong steps, On Start function does not operate properly.

Remote control

This projector has two different remote control codes; factory-set normal code (Code 1) and secondary code (Code 2). This switching function prevents remote control operation mixture (jam) when operating several projectors or video equipment together.

When operating projector in “Code 2,” both projector and Remote

Control Unit must be switched to “Code 2.”

To change code of Projector;

Set Remote control in SETTING MENU to “Code 2.”

To change code of Remote Control Unit;

Press both MENU and IMAGE buttons on Remote Control Unit together for over 10 seconds.

After changing code, make sure Remote Control operates properly.

To return to normal code (Code 1), operate both projector and

Remote Control in ways above again.

Network icon

This function cannot be adjusted when not attach the Network connection (optional part) to the projector.

Lamp counter reset

This function is used to reset Lamp Replace Counter. When replacing Projection Lamp, reset Lamp Replace Counter by using this function. Refer to page 40 for operation.

Quit

Closes SETTING MENU.

On start

On

Code 1

Lamp counter reset

On

Code 1

Press SELECT button at this icon to display other items.

Press SELECT button at this icon to display previous items.

Move pointer to item and then press

POINT LEFT/RIGHT button(s).

Move pointer to Lamp counter reset and then press

SELECT button. Message “Lamp replace counter reset?” is displayed.

APPENDIX

MAINTENANCE

WARNING TEMP. INDICATOR

1

2

3

WARNING TEMP. Indicator flashes red when an internal temperature of a projector exceeds normal temperature. This

Indicator stops flashing when temperature of a projector returns to normal.

When WARNING TEMP. Indicator continues to flash, check items listed below.

Ventilation Slots of a projector may be blocked. In such an event, reposition a projector so that Ventilation Slots are not obstructed.

Air Filter may be clogged with dust particles. Clean Air Filter by following section AIR FILTER CARE AND CLEANING below.

If WARNING TEMP. Indicator remains on after performing above checks, Cooling Fans or Internal Circuits may be malfunctioning. Contact service personnel from an authorized dealer or a service station.

AIR FILTER CARE AND CLEANING

3

4

Air Filter prevents dust from accumulating on surface of Projection Lens and Projection Mirror. Should Air Filter become clogged with dust particles, it will reduce Cooling Fans’ effectiveness and may result in internal heat build up and adversely affect life of a projector. Clean Air Filter following steps below:

1

2

Turn off a projector, and disconnect AC power cord from AC outlet.

Turn a projector upside down and remove Air Filter (2 used) by pulling latches upward.

Clean Air Filter with a brush or wash out dust and particles.

Replace Air Filter properly. Make sure that Air Filter is fully inserted.

CAUTION

Do not operate a projector with Air Filter removed. Dust may accumulate on LCD Panel and Projection Mirror degrading picture quality.

Do not put small parts into Air Intake Vents. It may result in malfunction of a projector.

AIR FILTER

Pull up and remove.

RECOMMENDATION

We recommend avoiding dusty/smoky environments when operating a projector. Usage in these environments may cause poor image quality.

When using under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical elements inside a projector. This condition may degrade quality of a projected image.

When above symptoms are noticed, contact a Boxlight Corporation at 1-800-762-5757 or 360-779-7901 for cleaning.

CLEANING PROJECTION LENS

2

3

Follow these steps to clean Projection Lens:

1

Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.

Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.

Lightly wipe a cleaning cloth over Projection Lens.

When a projector is not in use, replace Lens Cover.

Downloaded from ProjectorsManual.com Manuals

39

APPENDIX

LAMP REPLACE

When the life of the Projection Lamp of this projector draws to an end, the LAMP REPLACE indicator lights yellow. If this indicator lights yellow, replace the projection lamp with a new one promptly.

TOP CONTROL

This indicator lights yellow when the life of the projection lamp draws to an end.

Replace the Projection Lamp with a new one promptly.

Allow a projector to cool, for at least 45 minutes before you open Lamp Cover. The inside of a projector can become very hot.

CAUTION

For continued safety, replace with a lamp assembly of the same type.

Do not drop a lamp assembly or touch a glass bulb! The glass can shatter and may cause injury.

2

3

Follow these steps to replace lamp assembly.

1

Turn off a projector and disconnect AC plug. Allow a projector to cool for at least 45 minutes.

Loosen 2 screws with a screwdriver and open Lamp Cover.

4

Loosen 2 screws with a screwdriver and pull out Lamp Assembly by grasping Handle.

Replace Lamp Assembly with a new one and tighten 2 screws back. Make sure that Lamp Assembly is set properly. Replace

Lamp Cover and tighten 2 screws.

5

6

Connect AC Power Cord to a projector and turn it on.

Reset Lamp Replace Counter (refer to section “Lamp Replace

Counter” below).

NOTE : Do not reset Lamp Replace Counter when Projection

Lamp is not replaced.

LAMP

ASSEMBLY

LAMP COVER

HANDLE

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through Boxlight Corporation at 1-800-762-5757 or 360-779-7901. When ordering Projection Lamp, give following information to dealer.

Model No. of your projector

Replacement Lamp Type No.

:

:

STUDIO EXPERIENCE CINEMA 20HD

POA-LMP38

(Service Parts No. 610 293 5868)

APPENDIX

LAMP REPLACE COUNTER

Be sure to reset Lamp Replace Counter after the Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP

REPLACE Indicator stops lighting.

Lamp counter reset

1

2

Turn projector on, press MENU button and ON-SCREEN

MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SETTING Menu icon (refer to page 38).

Press POINT DOWN button to move a red frame pointer to

“Lamp counter reset” and then press SELECT button.

Message "Lamp replace counter reset?" is displayed. Move pointer to [Yes] and then press SELECT button.

3

Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter.

On

Code 1

Move pointer to Lamp counter reset and then press

SELECT button. Message “Lamp replace counter reset?” is displayed.

NOTE : Do not reset the Lamp Replace Counter until after the Projection Lamp is replaced.

LAMP HANDLING PRECAUTIONS

This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard.

● Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps.

● If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.

( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.

● A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

Downloaded from ProjectorsManual.com Manuals

41

APPENDIX

TROUBLESHOOTING

Before calling your dealer or service center for assistance, check matters below once again.

1. Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING

PROJECTOR" on pages 11 ~ 13.

2. Check cable connection. Verify that all computer, video and power cord are properly connected.

3. Verify that all power is switched on.

4. If a projector still does not produce an image, re-start your computer.

5. If an image still does not appear, unplug a projector from your computer and check your computer monitor's display.

Problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to turn computer and monitor off before you power up a projector. Power equipment back on in order of : Projector and computer.)

6. If problem still exists, check following chart.

Problem:

No power.

Image is out of focus.

Try these Solutions

Plug a projector into your AC outlet.

Make sure READY Indicator lights.

Wait 90 seconds after a projector is turned OFF when turning a projector back on.

NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as follows:

1. LAMP indicator lights bright and READY indicator turns off.

2. After 90 seconds, READY indicator lights green again and a projector may be turned on by pressing Power ON-OFF button.

Check WARNING TEMP. indicator. If indicator flashes red, a projector cannot be turned on.

(See "TURNING ON/OFF PROJECTOR" section on page 19.)

Check Projection Lamp. (Refer to page 40.)

Adjust focus of a projector.

Make sure a projection screen is at least 5.0’ (1.5m) from a projector.

Check Projection Lens to see if it needs cleaning.

NOTE : Moving a projector from a cool temperature location to a warm temperature location may result in moisture condensation on Projection Lens. In such an event, leave a projector OFF and wait until condensation disappears.

Check Ceiling / Rear feature. (See “SETTING” section on page 37.)

Picture is Left/Right reversed.

Picture is

Top/Bottom reversed.

Some displays are not seen during

Operation.

No image.

No sound.

Check Ceiling feature. (See “SETTING” section on page 37.)

Check Display feature.(See “SETTING” section on page 37.)

Check connection between your computer or video equipment and a projector.

When turning a projector on, it takes about 30 seconds to display an image.

Check system that you select is corresponding with your computer or video equipment.

Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).

Check audio cable connection from audio input source.

Adjust audio source.

Press VOLUME (+) button.

Press MUTE button.

APPENDIX

Problem:

Remote Control Unit does not work.

Try these Solutions

Check batteries.

Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.

Make sure you are not too far from a projector when using Remote Control Unit.

Maximum operating range is 16.4’ (5m).

Check transmitted signal mode from Remote Control Unit.

(See“SETTING” section on page 38.)

SERVICE

WARNING: High voltages are used to operate this projector. Do not attempt to open the cabinet.

Boxlight Service is easily obtained. If after following instructions above, you find that service is necessary, contact Boxlight for assistance at 1-800-762-5757 or 360-779-7901.

Give the model number and explain the difficulty. We will advise you how to obtain service.

Please have the following information available:

Serial Number of Projector.

Resolution of Computer.

Refresh rate of Computer.

This symbol on the nameplate means the product is Listed by Underwriters

Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards.

The CE Mark is a Directive conformity mark of the European Community (EC).

Downloaded from ProjectorsManual.com Manuals

43

APPENDIX

TECHNICAL SPECIFICATIONS

Projector Type

Dimensions

(W x H x D)

Net Weight

LCD Panel System

Panel Resolution

Number of Pixels

Color System

High Definition TV Signal

Scanning Frequency

Projection Lens

Throw distance

Motorized Lens Shift

Projection Image Size (Diagonal)

Horizontal Resolution

Projection Lamp

Input 1 Jacks

Input 2 Jacks

Input 3 Jacks

Other Jacks

Built-in Speakers

Feet Adjustment

Voltage and

Power Consumption

Operating Temperature

Storage Temperature

Accessories

Multi-media Projector

12.6" x 6.6" x 16.8" (319 mm x 168 mm x 429.5 mm)

17.4 lbs (7.9 kg)

1.21" TFT Active Matrix type, 3 panels

1366 x 768 dots

3,147,264 (1366 x 768 x 3 panels)

PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N

480i, 480p, 575i, 575p, 720p, 1035i and 1080i

H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz

F1.8 ~ 2.1 lens with f=48.4 mm ~ 62.8 mm Motor zoom and focus

5.0' (1.5 m) ~ 51.3' (15.6 m)

Up and Down

Adjustable from 31" to 400"

800 TV lines (HDTV)

200 watt type

DVI Terminal (Digital), HDB 15-pin Terminal (Analog) and Stereo Mini Type Jack (Audio)

BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H and V), Stereo Mini

Type Jack (Audio)

RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L) and DIN 4-pin (S-Video)

DIN 8-pin (Control port), Wired Remote Jack and Network Connector

INT. SP. Stereo (R and L), 2 watt RMS (T.H.D. 10%)

0˚ to 10.5˚

AC 100 ~ 120 V (3.6 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)

AC 200 ~ 240 V (1.8 A Max. Ampere), 50 / 60 Hz (Continental Europe)

41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)

14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)

User’s Guide

AC Power Cord

Wireless/Wired Remote Control Transmitter and Batteries

Remote Control Cable

Video Cable (RCA x 1)

Audio Cable (RCA x 2)

S-Video Cable

Control (Serial) port Cable

Protective Dust Cover

Lens Cover

Specifications are subject to change without notice.

LCD panels are manufactured to the highest possible standards. At least 99.99% of the pixels are effective, however a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.

APPENDIX

CONFIGURATIONS OF TERMINALS

COMPUTER INPUT-1 TERMINAL (ANALOG)

Terminal : HDB15-PIN

Connect display output terminal of computer to this terminal with VGA Cable (not supplied). When connecting Macintosh computer, MAC Adapter (not supplied) is required.

Pin Configuration

5

15

4 3

10

9

14 13

8

2

12

1

7

11

6

6

7

4

5

8

1

2

3

Red Input

Green Input

Blue Input

Sense 2

Ground (Horiz.sync.)

Ground (Red)

Ground (Green)

Ground (Blue)

12

13

14

15

9

10

11

+5V Power

Ground (Vert.sync.)

Sense 0

DDC Data

Horiz. sync.

Vert. sync.

DDC Clock

COMPUTER INPUT-1 TERMINAL (DIGITAL)

Terminal : DVI 24-pin

Connect display output terminal of computer to this terminal with DVI cable (for Single Link T.M.D.S. / not supplied).

Pin Configuration

1

9

2

10

3

11

4

12

5

13

6

14

7

15

17 18 19 20 21 22 23

8

16

24

6

7

4

5

8

1

2

3

T.M.D.S. Data2–

T.M.D.S. Data2+

T.M.D.S. Data2 Shield

No Connect

No Connect

DDC Clock

DDC Data

No Connect

12

13

14

15

16

9

10

11

T.M.D.S. Data1–

T.M.D.S. Data1+

T.M.D.S. Data1 Shield

No Connect

No Connect

+5V Power

Ground (for +5V)

Hot Plug Detect

20

21

22

23

24

17

18

19

T.M.D.S. Data0–

T.M.D.S. Data0+

T.M.D.S. Data0 Shield

No Connect

No Connect

T.M.D.S. Clock Shield

T.M.D.S. Clock+

T.M.D.S. Clock–

CONTROL PORT CONNECTOR

Terminal : Mini DIN 8-PIN

Connect serial port on your computer to this connector with Control Cable (supplied).

Pin Configuration

5

8 7 6

4 3

2

1

7

8

5

6

3

4

1

2

PS/2

-----

CLK

DATA

GND

-----

-----

GND

-----

Serial

R X D

-----

-----

GND

RTS / CTS

T X D

GND

GND

ADB

-----

ADB

-----

GND

-----

-----

-----

GND

Downloaded from ProjectorsManual.com Manuals

45

Downloaded from ProjectorsManual.com Manuals

47

LIMITED WARRANTY

BOXLIGHT Corporation (“BOXLIGHT”) warrants that each Cinema 20HD (“the Product”) sold hereunder will conform to and function in accordance with the written specifications of BOXLIGHT. Said limited warranty shall apply only to the first person or entity that purchases the Product for personal or business use and not for the purpose of distribution or resale.

Said warranty shall continue for a period of three (3) years from the date of such purchase. The standard limited warranty excludes the lamps in projectors after 120 days and the accessories after one year. BOXLIGHT does not warrant that the

Product will meet the specific requirements of the first person or entity that purchases the Product for personal or business use. BOXLIGHT’s liability for the breach of the foregoing limited warranty is limited to the repair or replacement of the

Product or refund of the purchase price of the Product, at BOXLIGHT’s sole option. Replacement Product may be refurbished in “like-new” condition, at BOXLIGHT’s sole discretion. To exercise the Purchaser’s rights under the foregoing warranty, the Product must be returned at the Purchaser’s sole cost and expense, to BOXLIGHT or to any authorized

BOXLIGHT service center provided, and the Product must be accompanied by a written letter explaining the problem and which includes (i) proof of date of purchase; (ii) the dealer’s name; and (iii) the model and serial number of the Product.

When sending your unit in for repair, please ship your unit in its original packing material or a BOXLIGHT approved ATA

Shipping Case, or have a professional packaging company pack the unit. Please insure your shipment for its full value. A return authorization number, issued by the BOXLIGHT customer service department, must also be clearly displayed on the outside of the shipping carton containing the Product.

WARRANTY LIMITATION AND EXCLUSION

BOXLIGHT shall have no further obligation under the foregoing limited warranty if the Product has been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized modifications, tampering, alterations, or service other than by BOXLIGHT or its authorized agents, causes other than from ordinary use or failure to properly use the Product in the application for which said Product is intended.

DISCLAIMER OF UNSTATED WARRANTIES

THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MER-

CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES

THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE EXTENDED,

ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY BOXLIGHT. SOME STATES DO NOT

ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT

APPLY TO YOU.

LIMITATION OF LIABILITY

IT IS UNDERSTOOD AND AGREED THAT BOXLIGHT’S LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER ANY

WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE

PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL BOXLIGHT BE LIABLE FOR

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS, LOST REVENUES OR

LOST SAVINGS. THE PRICE STATED FOR THE PRODUCT IS A CONSIDERATION IN LIMITING BOXLIGHT’S

LIABILITY. NO ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO PURCHASE THE

PRODUCT MAY BE BROUGHT BY PURCHASER MORE THAN ONE YEAR AFTER THE CAUSE OF ACTION HAS

ACCRUED. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS

LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT

VARY FROM STATE TO STATE.

Boxlight

19332 Powder Hill Place

Poulsbo, WA 98370-7407 USA www.boxlight.com

U.S. and Canada 800-762-5757

International 1-360-779-7901

Printed in Japan

Part No. 610 303 0365 (1AA6P1P3653-- M4LE)

Downloaded from ProjectorsManual.com Manuals

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement